Tech Problem Aggregator

Error 1075

Q: Error 1075

My computer is stuck on "Acquiring Network address". I have tried to go into the services, and turn on the DHCP Client, however I get an Error 1075: The dependency service does not exist or has been marked for deletion, and it will not start. I am running Windows XP Home Edition, SP3. I thank you in advance for the help.

A: Error 1075

Hi -See if this reset works first. Please read carefully -TCP/IP NetBIOS Helper error 1075 TCP/IP stack repair options for use with Windows XP with SP2/SP3.Start, Run, Type CMD to open a command prompt:In the command prompt window that opens, type the following commands, each followed by the Enter key:Note: Type only the text in bold for the following commands.Reset TCP/IP stack to installation defaults, type: netsh int ip reset reset.log Reset WINSOCK entries to installation defaults, type: netsh winsock reset catalogReboot the machine. Thank You - EDITED to reset commands -

12 more replies
Answer Match 58.38%

Avg found two trojans. It didn't seem like it removed them. Internet was working though. Ran malwarebytes it found nothing. Internet was still working. Started Having connectivity issues. My dhcp client service won't start. I got a 1075 error. my internet via wifi or wired won't work. I ran the following command prompts:
net start AFD (response: the requested has already been started)
netsh int ip reset reset.log (response: resetting echo request, failed. Access is denied. Rebooting interface, ok! A reboot is required to complete this action.
netsh winsock reset catalog (response: successfully reset the winsock catalog. You must restart the computer in order to complete the reset.
SFC /SCANNOW (scan finishes and shows this response: windows resource protection found corrupt files but was unable to fix some of them. Details are included in the cbs.log windir\logs\cbs\cbs.log

I can't run the programs you suggested as I have no internet access. What now? Please help.
 

A:Help 1075 Error

I will try to run the items above in the other thread in safe mode and paste results. Sorry about that.
 

2 more replies
Answer Match 58.38%

I recently had to reinstal Windows XP Media Center SP3 operating system on my Dell Inspiron 9300 laptop. When trying to install Pure Networks Net Magc Pro it will not run as it says the platform service is no running. When I try to start the platform service I get the following Error 1075: The dependency service does not exist or has been marked for deletion.
Does anyone know how to correct this situation.

Thanks.

A:ERROR 1075

Why not post to the NetMagic forum. You will have more luck there then in this
General Microsoft Forum

2 more replies
Answer Match 58.38%

My internet will not connect It Keeps saying Acquiring network address, I have tried everything even going into Services.msc to Start DHCP client and it gives me this error
Error 1075, The dependency service does not exist or has been marked for deletion

I am running Windows XP Home Edition SP3 and its Dell

A:Error 1075

First , you may have done this but ..... check if you can start the dependency service for DHCP client service.To view the dependency services registered for DHCP Client Service, try the following steps? Click on Start and them type cmd and press Enter? In the command prompt type: CMD /K SC QC DHCP - Please note the spaces -? Press Enter check if the dependency service is started.Verify that the Dependency Service / components are runningNext -To verify that the three dependency components are running. Follow the steps below:? Click Start, Run and type DEVMGMT.MSC - No spaces -? In the View menu, click Show hidden devices? Double-click Non-Plug and Play drivers section? Double-click the entry AFD, and click the Driver tab? Set the Startup type to System.? Start the service. Note down the error message if any.? Similarly start the two other drivers namely:? TCP/IP Protocol Driver? NetBios over Tcpip? Close Device Manager and restart Windows.? Now check if you can start the DHCP service.Let us know if you have done all this, and we can look for more ideas -

4 more replies
Answer Match 57.96%

When I try to connect my printer lexmark 4200 series I get the message no print spooler available error 1075 Please HELP!!!

A:[SOLVED] Error 1075

I would make sure the print spooler service is enabled.

Go to Start > Run... and type services.msc to open the service snap-in. Then Scroll down to Print Spooler. Right click on it and click Start. Then right click on it, select Properties, and set the startup type to Automatic.

9 more replies
Answer Match 57.96%

Hello,

I'm recently recovering from a mild virus infection on my computer, and noticed that after I had run Avast! and Malwarebytes to remove the virus, my computer lost its internet functionality. Upon running ipconfig in command prompt, I noticed that the computer was not being assigned an IP address, which lead me to believe there could be an issue with DHCP.

When running services.msc, I notice that both DHCP client and TCP/IP netbios are not running, and when I try to run them, I get an error 1075, that the files are "either non-existent or marked for deletion". I noticed that someone else had posted a very similar problem, but a few of the fixes were not available for viewing/download as they were specifically tailored for that issue.

I'm currently running Windows XP Media Center, Service Pack 3 on a Dell Inspiron E1505 laptop I had purchased in mid-2006.
 

A:DHCP and TCP/IP Error 1075

Below is a copy of the Hijack This log.

Logfile of Trend Micro HijackThis v2.0.4
Scan saved at 9:03:31 PM, on 12/26/2011
Platform: Windows XP SP3 (WinNT 5.01.2600)
MSIE: Internet Explorer v8.00 (8.00.6001.18702)
Boot mode: Normal

Running processes:
C:\WINDOWS\System32\smss.exe
C:\WINDOWS\system32\winlogon.exe
C:\WINDOWS\system32\services.exe
C:\WINDOWS\system32\lsass.exe
C:\WINDOWS\system32\Ati2evxx.exe
C:\WINDOWS\system32\svchost.exe
C:\WINDOWS\System32\svchost.exe
C:\Program Files\Alwil Software\Avast5\AvastSvc.exe
C:\WINDOWS\system32\Ati2evxx.exe
C:\WINDOWS\Explorer.EXE
C:\WINDOWS\system32\spoolsv.exe
C:\WINDOWS\ehome\ehtray.exe
C:\Program Files\Synaptics\SynTP\SynTPEnh.exe
C:\Program Files\ATI Technologies\ATI.ACE\cli.exe
C:\Program Files\SigmaTel\C-Major Audio\WDM\stsystra.exe
C:\Program Files\Microsoft Office\Office12\GrooveMonitor.exe
C:\Program Files\VERIZONDM\bin\sprtcmd.exe
C:\Program Files\Adobe\Reader 9.0\Reader\Reader_sl.exe
C:\Program Files\Alwil Software\Avast5\avastUI.exe
C:\Program Files\Java\jre6\bin\jusched.exe
C:\WINDOWS\system32\ctfmon.exe
C:\Program Files\Bonjour\mDNSResponder.exe
C:\Program Files\LogMeIn Hamachi\hamachi-2.exe
C:\Program Files\Java\jre6\bin\jqs.exe
c:\PROGRA~1\mcafee\SITEAD~1\mcsacore.exe
C:\Program Files\VERIZONDM\bin\sprtsvc.exe
C:\Program Files\VERIZONDM\bin\tgsrvc.exe
C:\WINDOWS\system32\rundll32.exe
C:\WINDOWS\system32\SearchIndexer.exe
C:\WINDOWS\system32\wuauclt.exe
C:\Documents and Settings\Shivang\Desktop\HijackThis.exe
C:\WI... Read more

2 more replies
Answer Match 57.96%

Hello all,

I've noticed that a few people have posted concerning this topic, so I've tried to read up on as many possible solutions before posting. I'm recently recovering from a mild virus infection on my computer, and noticed that after I had run Avast! and Malwarebytes to remove the virus, my computer lost its internet functionality. Upon running ipconfig in command prompt, I noticed that the computer was not being assigned an IP address, which lead me to believe there could be an issue with DHCP.

When running services.msc, I notice that both DHCP client and TCP/IP netbios are not running, and when I try to run them, I get an error 1075, that the files are "either non-existent or marked for deletion". I noticed that someone else had posted a very similar problem, but a few of the more advanced fixes seemed specifically tailored for their issue.

Below are the fixes I've attempted thus far -

1. Checked the registry for DHCP?s dependencies (3 are listed, Afd, Tcpip, and NetBT).
2. Reset TCP/IP stack to installation defaults by typing ?netsh int ip reset reset.log? into command prompt.
3. Reset WINSOCK entries to installation defaults by typing ?netsh winsock reset catalog? into command prompt.
4. Ran ?sfc /scannow? with an XP SP3 CD.

I'm currently running Windows XP Media Center, Service Pack 3 on a Dell Inspiron E1505 laptop I had purchased in mid-2006.

A:DHCP and TCP/IP Error 1075

Welcome aboard Please download Farbar Service Scanner and run it on the computer with the issue.Make sure the following options are checked:Internet ServicesWindows FirewallSystem RestoreSecurity CenterWindows UpdatePress "Scan".It will create a log (FSS.txt) in the same directory the tool is run.Please copy and paste the log to your reply.

7 more replies
Answer Match 57.96%

DHCP error 1075--can not start the DHCP client on local computer.Dependency service does not exist or has been marked for deletion..

Hi thanks for any help you can give.
Machine is a Dell dimension e520
Win XP Media center edition SP 2

I have the original dell discs and access to a working laptop also running win XP [this one]

During a routine virus scan by avira anti vir it quarentined c:\windowes\system32\drivers\netby.sys.

This disabled the DHCP client so no IP traffic
I restored the file but still no luck

After trying to renew the IP and some searching around I found that the HKEY local machine system currentcontrolset services NETbt registry key is missing

In services DHCP cannot be restarted --gives the warning above.
AFD and TCP/IP are in device manager -non plug & play show hidden devices NETbt is not

Can the registry be repaired from the original discs without having to reinstall everything else?
Or is it as easy as inserting the missing registry key?

Thanks Bob

A:DHCP error 1075

Hi see if this can help How to fix: Error 1075, The dependency service does not exist or has been marked for deletion | Kaliphonia.com

1 more replies
Answer Match 57.96%

My windows fire wall wont start Ive tried starting it in services and the action center but no luck, i know their might be a hardware change or virus or malware that has done this but im unable to pin point it the date of any change because Ive only just realized that the firewall was off because i wanted to block a game from accessing the Internet. Ive scanned countless times but it says its clean.  Also windows update wont install updates and system recovery doesn't work...Ive been trying to follow instructions that have been given to other people but with no luck, any help will be appreciated.
 
my PC: 

OptiPlex 760 (Late 2008)

Service Tag: 5M0YJ4J | Express Service Code: 12215778643
32 bit operating system win 7 home premium 
 

 
many thanks

A:!!firewall error 1075!!

Please download and install Speccy to provide us with information about your computer.  When  FileHippo opens, click on Download latest version in the upper right pane. When Speccy opens you will see a screen similar to the one below.  Click on File which is outlined in red in the screen above, and then click on Publish Snapshot. The following screen will appear, click on Yes.  The following screen will appear, click on Copy to Clipboard.  In your next post right click inside the Reply to Topic box, then click on Paste.  This will load a link to the Speccy log.  Please download MiniToolBox, save it to your desktop and run it. Checkmark the following checkbox: List Installed Programs Click on Go to start the scan.  Once it is finished highlight the text, copy it and paste it in your next post. Try the following.  Click on the Start orb, then type Services in the Search programs and files box. Services will appear above the search box under Programs, right click on Services and choose Run as administrator. When Services opens scroll down to until you find Windows Firewall, double click on it. Click the Startup type box and make sure it is set to Automatic, if it isn't click on Automatic. Look in the Service status to see if it is running, if it isn't click on Start, then click on Apply, then OK. Scroll down to Base Filtering Engine and doulbe click on it.... Read more

11 more replies
Answer Match 57.96%

I am having the same issues as the other thread that is currently going on regarding a virus that seems to have left me unable to connect to the internet , i have done the hijack this report and will post results . please help!!
Logfile of Trend Micro HijackThis v2.0.4
Scan saved at 9:17:51 PM, on 12/20/2011
Platform: Windows XP SP2 (WinNT 5.01.2600)
MSIE: Internet Explorer v6.00 SP2 (6.00.2900.2180)
Boot mode: Normal

Running processes:
C:\WINDOWS\System32\smss.exe
C:\WINDOWS\system32\winlogon.exe
C:\WINDOWS\system32\services.exe
C:\WINDOWS\system32\lsass.exe
C:\WINDOWS\system32\svchost.exe
C:\WINDOWS\System32\svchost.exe
C:\WINDOWS\system32\spoolsv.exe
C:\WINDOWS\Explorer.EXE
C:\Program Files\Adobe\Adobe Version Cue CS2\ControlPanel\VersionCueCS2Tray.exe
C:\Program Files\LeapFrog\LeapFrog Connect\Monitor.exe
C:\Program Files\Common Files\Java\Java Update\jusched.exe
C:\WINDOWS\system32\spool\drivers\w32x86\3\hpztsb10.exe
C:\Program Files\Google\GoogleToolbarNotifier\GoogleToolbarNotifier.exe
C:\Program Files\SUPERAntiSpyware\SUPERAntiSpyware.exe
C:\Program Files\Spybot - Search & Destroy\TeaTimer.exe
C:\Program Files\Hewlett-Packard\Digital Imaging\bin\hpotdd01.exe
C:\Program Files\NETGEAR\WG111T\wlan111t.exe
C:\WINDOWS\system32\netdde.exe
C:\Program Files\SUPERAntiSpyware\SASCORE.EXE
C:\WINDOWS\system32\CTsvcCDA.EXE
C:\Program Files\Java\jre6\bin\jqs.exe
C:\Program Files\LeapFrog\LeapFrog Connect\CommandService.exe
C:\WINDOWS\system32\svchost.exe
C:\WINDOWS\system32\Ms... Read more

A:Error 1075 no internet

help
 

1 more replies
Answer Match 57.96%

The full message is error 1075: The dependancy service either does not exist or has been marked for deletion

This started with a tidserv!inf infection. Norton End-Point seems to have deleted all related virus infections, however, I am now unable to start the DHCP service. I have to set a static IP in order to connect to the internet.

I believe tdx.dll was identified as a virus and deleted. it was listed as a dependancy of dhcp but had no descriptor. Currently it is not listed as a dependancy.

I cannot view network shares from this PC nor can I view shares that I host here on other PC's. Only this computer shows up in net places.

I did an sfc /scannow and it told me audiodev.dll and mofd.dll were corrupted and the files in the store have been corrupted.

I had to take ownership with the admin group in order to replace them with extracted copies from my windows cd, but I when I went back to reassign trustedinstaller as the owner it was not listed as an option.

my cd is without service pack and my installed service pack is sp2.

can anyone be of assistance.

A:DHCP error 1075

My dhcp was working for a day but its back down again. i dont know how to recreate the dependancy on tdx

2 more replies
Answer Match 57.96%

DHCP and TCP/IP can not be started from Services with out the following error.

Error 1075: The dependency service does not exist or has been marked for deletion.

I've checked the dependencies and all are running.

AFD is the only driver common to both DHCP and TCP/IP so I assumed it is either not running or is corrupt..yet when I try to start AFD from the CMD prompt I get...."service is already running.

I have since disabled my Lan Connection via Network Connections as it just sits there trying to acquire ip without ever timing out.

I also performed a registry scan with Registry Booster in Safe Mode. It reported:

1061 System Errors
205 User Errors, and
1 Third Party Error

A cursory review of the log tells me the majority have to do with poorly uninstalled programs. I did NOT let Registry Booster fix anything.

As per Forum Rules my HiJackThis log and others follow:

Logfile of Trend Micro HijackThis v2.0.4
Scan saved at 7:57:39 PM, on 11/26/2011
Platform: Windows XP SP2 (WinNT 5.01.2600)
MSIE: Internet Explorer v7.00 (7.00.6000.16791)
Boot mode: Normal

Running processes:
C:\WINDOWS\System32\smss.exe
C:\PROGRA~1\AVG\AVG10\avgchsvx.exe
C:\WINDOWS\system32\winlogon.exe
C:\WINDOWS\system32\services.exe
C:\WINDOWS\system32\lsass.exe
C:\WINDOWS\system32\svchost.exe
C:\WINDOWS\System32\svchost.exe
C:\WINDOWS\system32\spoolsv.exe
C:\WINDOWS\Explorer.EXE
C:\Program Files\Pure Networks\Network Magic\nmapp.exe
C:\Program Files\QuickTime\QTTask.exe
C:\Program Files\AVG\A... Read more

A:Error 1075 Can not Acquire Ip

16 more replies
Answer Match 57.96%

Hello All,

I've tried most of today to get rid of a nasty trojan. System-Check!

I'm almost there - or so I thought. Visually my laptop seems to looking okay, except, I can't seem to restart my Firewall within McAfee?

Here's a DDS:
**** EDITED ****

DDS removed - as I managed to solve issue by uninstalling MCafee and reinstlling.
Mods - please remove post or close. thanks

A:McAfee 1075 Error

Mods - please close post or remove.

thank you.

2 more replies
Answer Match 57.12%

Help me please, I have the same problem, and here is the SystemLook result:

SystemLook 30.07.11 by jpshortstuff
Log created at 09:34 on 18/12/2011 by USER
Administrator - Elevation successful

========== filefind ==========

Searching for "afd.sys"
C:\Windows\System32\drivers\afd.sys --a---- 338944 bytes [12:25 16/12/2011] [12:21 16/12/2011] 9EBBBA55060F786F0FCAA3893BFA2806
C:\Windows\winsxs\x86_microsoft-windows-winsock-core_31bf3856ad364e35_6.1.7600.16385_none_d7be98b5bfc0b4c1\afd.sys --a---- 338944 bytes [23:12 13/07/2009] [23:12 13/07/2009] DDC040FDB01EF1712A6B13E52AFB104C
C:\Windows\winsxs\x86_microsoft-windows-winsock-core_31bf3856ad364e35_6.1.7600.16802_none_d81220b5bf827af7\afd.sys --a---- 338944 bytes [10:52 17/06/2011] [02:35 25/04/2011] 0DB7A48388D54D154EBEC120461A0FCD
C:\Windows\winsxs\x86_microsoft-windows-winsock-core_31bf3856ad364e35_6.1.7600.20951_none_d864ad9ad8c98d1f\afd.sys --a---- 338944 bytes [10:52 17/06/2011] [02:27 25/04/2011] C114AB7A1550D42EA1700FFD4179CF5A
C:\Windows\winsxs\x86_microsoft-windows-winsock-core_31bf3856ad364e35_6.1.7601.17514_none_d9efac7dbcaf385b\afd.sys --a---- 338944 bytes [02:30 09/07/2011] [08:40 20/11/2010] 1151FD4FB0216CFED887BFDE29EBD516
C:\Windows\winsxs\x86_microsoft-windows-winsock-core_31bf3856ad364e35_6.1.7601.17603_none_d9f97e05bca8003a\afd.sys --a---- 338944 bytes [12:25 16/12/2011] [12:21 16... Read more

A:Cannot connect to internet - Error 1075

Can I see you FSS log again?

http://download.bleepingcomputer.com/farbar/FSS.exe

and run it on the computer with the issue.

* Press "Scan".
* It will create a log (FSS.txt) in the same directory the tool is run.
* Please copy and paste the log to your reply.

1 more replies
Answer Match 57.12%

When I try to start the DNS server service on a windows 2000 server it won't start and gives me an error 1075 and says "The dependency service does not exist or has been marked for deletion. Any suggestions, help or advice would be gratefully appreciated.
 

A:Server DNS Issue - Error 1075

Take a look at this see if it helps:

http://support.microsoft.com/kb/839089
 

1 more replies
Answer Match 57.12%

Need help solving Error #1075 problem in conjunction with CheckPoint VPN NGX R60 HFA3. I am using a Dell E6510 laptop computer running Windows 7 Ultimate 32-bit OS. I can get this VPN to run and connect when I use Microsoft's XP virtual machine sitting on the Windows 7 desktop but I cannot get it to run on the Windows 7 desktop by itself.

Although the VPN seems to load without incident the associated icon "key" does not appear in the notification tray at the lower right. It does appear in the XP virtual machine and on a separate HP desk top running Vista.

When I type services.msc at the Win 7 command prompt I get a list of all the loaded services including the CheckPoint VPN. It is at this point when I try to start the VPN I get the 1075 error. When I check the dependencies under the VPN I find the "CheckPoint Office Mode Module" and the "VPN-1 Module".

How do I determine if these dependencies are causing the 1075 error message? What steps do I need to take to resolve the error message so the VPN will start?

A:CheckPoint VPN Causing Error #1075

make sure your Firewall is allowing the following:
SR_SDS.EXE
SR_GUI.EXE
SR_WATCHDOG.EXE
SR_SERVICE.EXE


If you're running 3rd party software FW, disable or uninstall it.

1 more replies
Answer Match 57.12%

I have read through the original thread (now closed) and tried all it's suggestions. However, I am still having the same IP (on lack of) issues. I ended my efforts with the running of SFC /SCANNOW which took a considerable amount of time, but resulted in no errors of any kind.

I continue to get the Error 1075: the dependency service does not exist or has been marked for deletion, message when trying to start the DHCP Client.

I'm afraid searching the suggested logs for the dependency items it a little over my head.

A little background for my situation. The computer in question is my teenage daughters. A week ago she started having problems with the internet and I'm assuming this is some sort of virus. Whenever selecting a website to launch to, something intervenes and chooses some alternate website. Never the same one twice. I loaded AVAST free version and did a scan. I also updated Malware Bytes and did another scan. I then loaded Kaspersky TDDS killer and did a scan with that. After all that, and roughly 15 files quarantined and deleted, I now have this IP problem. I cannot restore the computer back to an earlier time.

Help would be greatly appreciated!
 

A:DHCP Error 1075 Cont.

16 more replies
Answer Match 57.12%

My computer is forever stuck on "Acquiring Network address". I have tried to go into the services, and turn on the DHCP Client, however I get an Error 1075: The dependency service does not exist or has been marked for deletion, and it will not start. Hopefully someone can help out. (Note: This is not the affected computer, the logs are from it, however) I am running Windows XP Home Edition, SP3. I thank you in advance for the help.

A:Cannot connect to internet - Error 1075

Hi -As long as you can understand the 'reasonably basic' directions, there is a solution here -http://www.google.com.au/url?sa=t&rct=j&q=error%201075&source=web&cd=1&ved=0CDsQFjAA&url=http%3A%2F%2Fkaliphonia.com%2Fcontent%2Fwindows%2Fhow-to-fix-error-1075-the-dependency-service-does-not-exist-or-has-been-marked-for-d&ei=jwvpTrX9K4fBiQfsoqHSCA&usg=AFQjCNGUfPzx_GkR2922eUot0LA67VjvMAThank You -

25 more replies
Answer Match 57.12%

My computer is forever stuck on "Acquiring Network address". I have tried to go into the services, and turn on the DHCP Client, however I get an Error 1075: The dependency service does not exist or has been marked for deletion, and it will not start. Attached is the logs you wished. Hopefully someone can help out. (Note: This is not the affected computer, the logs are from it, however) I am running Windows XP Home Edition, SP3. I thank you in advance for the help.

Logfile of Trend Micro HijackThis v2.0.4
Scan saved at 8:29:14 AM, on 12/13/2011
Platform: Windows XP SP3 (WinNT 5.01.2600)
MSIE: Internet Explorer v8.00 (8.00.6001.18702)
Boot mode: Normal

Running processes:
C:\WINDOWS\System32\smss.exe
C:\WINDOWS\system32\winlogon.exe
C:\WINDOWS\system32\services.exe
C:\WINDOWS\system32\lsass.exe
C:\WINDOWS\system32\Ati2evxx.exe
C:\WINDOWS\system32\svchost.exe
C:\WINDOWS\System32\svchost.exe
C:\WINDOWS\system32\spoolsv.exe
C:\Program Files\Bonjour\mDNSResponder.exe
C:\Program Files\Java\jre6\bin\jqs.exe
C:\Program Files\Common Files\Symantec Shared\PIF\{B8E1DD85-8582-4c61-B58F-2F227FCA9A08}\PIFSvc.exe
C:\Program Files\McAfee\SiteAdvisor\McSACore.exe
C:\Program Files\Common Files\Motive\McciCMService.exe
C:\Program Files\Common Files\McAfee\McSvcHost\McSvHost.exe
C:\WINDOWS\system32\mfevtps.exe
C:\WINDOWS\system32\HPZipm12.exe
C:\Program Files\Analog Devices\SoundMAX\SMAgent.exe
C:\WINDOWS\system32\svchost.exe
C:\Program Files\Yahoo!\SoftwareUpdate\YahooAUService.exe
C... Read more

A:Cannot connect to internet - Error 1075

Thanks for the quick response guys, You're a lifesaver. I shall be sure to recommend that all my friends come to http://www.bleepingcomputer.com for all their troubles too!
 

1 more replies
Answer Match 57.12%

DHCP Client will not start from services menu and neither will TCP/IP all other networking services appear to be started and working.

DHCP dependencies are:

AFD Networking Support Environment
TCP/IP Protocol
IPSEC driver
TCP/IP dependencies are:
AFD

Since the TCP/IP's only dependency is AFD I suspect it has been deleted or corrupted. How do I go about fixing that?

Paste SYSINFO.txt

Tech Support Guy System Info Utility version 1.0.0.2
OS Version: Microsoft Windows XP Professional, Service Pack 2, 32 bit
Processor: Intel(R) Pentium(R) 4 CPU 2.80GHz, x86 Family 15 Model 3 Stepping 4
Processor Count: 1
RAM: 1023 Mb
Graphics Card: NVIDIA Quadro NVS 280 SD, 64 Mb
Hard Drives: C: Total - 38099 MB, Free - 8667 MB; E: Total - 29313 MB, Free - 16148 MB; X: Total - 95393 MB, Free - 69980 MB;
Motherboard: Dell Computer Corp., 0W2563
Antivirus: AVG Anti-Virus Free Edition 2011, Updated: Yes, On-Demand Scanner: Enabled
I already reset the ip stack with the following to no avail.

Reset TCP/IP stack to installation defaults, type: netsh int ip reset reset.log

Reset WINSOCK entries to installation defaults, type: netsh winsock reset catalog

Reboot the machine.

I'd really like to avoid the nuclear option. Any assistance is greatly appreciated.

Thanks
 

A:Solved: Error 1075 Can not Acquire Ip

8 more replies
Answer Match 57.12%

Greetings,
I am having a major DHCP error on my girlfriend's laptop. I am primarily a Linux user so I'm kinda lost here as her machine is running XP. It's a Dell XPS M1210 which, conveniently, did not come with a recovery CD or even partition.
Anyway, a few weeks ago her wireless network device stopped working. It would look like it was connecting, but it would hang on "Acquiring network address." At first I thought maybe the device was shot, until I had the chance to test out the wired ethernet, which has the same problem.
After quite a bit of googling, I ran services.msc, and saw that DHCP is not running. When I try to start it from that menu, however, I get this message: "Could not start the DHCP Client service on Local computer. Error 1075: The dependency service does not exist or has been marked for deletion."
After more googling, I discovered that DHCP has only 3 dependencies: TCP/IP, AFD, and NetBt. I checked the registry, and those were the only ones listed.
After even more googling, I ran devmgmt.msc and selected "show hidden devices" and double clicked on "non plug and play devices." I TCP/IP and AFD are both there. NetBt, however, is not.
I've spent hours doing further googling and tried pretty much every fix I could find and nothing seems to work. If the PC had shipped with a recovery CD I imagine this would be easy to fix but alas no luck. I need to get this working so I can set up my new internets and I... Read more

A:Solved: DHCP Error 1075

15 more replies
Answer Match 56.7%

My PC is three years old and has been a great machine. I run Windows XP Home Edition, I.E. 7 and have all the protection installed I can find.

Quite by accident I discovered my System Restore is not working. I don't need it at the moment (!!!) but I like everything to be as near as perfect as possible on my PC so I have been trying to discover what the SR problem is and how I can resolve it.

I keep getting the message "S R is not able to protect your computer. Please restart and run SR again"............This advice does not work. for me!
I cannot turn off SR for the same reason.

I then checked out this section of the forum and discovered that many people have had this same problem. I have tried downloading Kelly's file 238 (I think that was the number) ; I have tried accessing services.msc ; I have tried accessing i386: nothing!

I did get the message "Error 1075: "Dependency service does not exist or has been marked for deletion". This error seeems to apply to many facilities on a PC.

I have my windows XP disk but cannot lay my hands on the SP2 one so I don't want to mess about without your professional advice to do so!! (apologies!)

As I said, if you solve my problem you will be miracle workers and worthy of your wings.

My thanks for any help you can offer me.

A:System Restore Won't Work : Error 1075

Right click My Computer > Manage > Expand Event Viewer > Look under Application and/or System to see if there is any event reporting on about System Restore.

Please do let us know if there is, a screenshot would be a great help.

Another workaround would be searching for sr.inf, right click it and select "Install". You might need Window XP install disc.

61 more replies
Answer Match 55.86%

This is my sister's netbook. The problems started with one of those new "fake antivirus" that puts up a ton of obviously fake results that claim your computer is highly infected*. She being... less technologically inclined apparently decided to run the "Antivirus scan" over and over again over night and then the next day gave it to me to try to figure out what was wrong. I can't find the links right now but I found a bunch of blogs that mentioned (Privacyprotection.exe) and among the most frustrating aspects what that it blocked pretty much everything from running. I did a bit of digging and eventually found out it was a rootkit causing the issues and the tools they gave me wouldn't run but I was able to follow the manual instructions. (remove the .exe, remove the alias, regedit and remove the key that matched privacyprotection.exe but not the other ones like the one underchrome etc).That took care of the major problem and I was able to get Microsoft Security Essentials running but everyscan kept turning up a few "Trojans" and that upon trying to clean would result in an error. The error would lead to 'restart to finish removel'. I tried safe mode and the same result. One top of that google results kept getting redirected (forget the site right now.. something like awesomesearch.com or what have you). I decided to try from another angle the redirect angle and found thishttp://www.bleepingcomputer.com/forums/topic422038.htmlI t... Read more

More replies
Answer Match 55.86%

Hey all!
I am really desperate. I've tried a few things that other people have posted here, especially Cookiegal and Lumpola but this issue persists.

I had a virus. I think I got rid of it. Avast scans and boot time scans and Super Anti Spyware and TDSS killer report all clear. However, the network shield of Avast and the Internet don't work.
Points to note:
1. In services, the DHCP and DNS cannot be started. I get the error 1075: service has been marked for deletion or one of it's dependancies are missing. (close to that)

I've checked the dependancies of both, and reinstated the ADF module in device manager after selecting the 'View Hidden' option.
 

A:DHCP Server Service -Error 1075 - not starting

2. I've tried deleting the winsock and winsock2 entries in the registry.
3. From the command prompt, SFC/scan now terminates at 82%. thrice.
4. I can see the network, both wired and wireless, I can connect, but it says I have limited connectivity.
 

3 more replies
Answer Match 55.86%

Hey Everyone.

Maybe someone could be of help. I have gone through several different forums and have attempted several ways to try to fix this but have had no luck.

I have tried the netsch winsock reset
I have tried the ipconfig /renew
My DNS service starts but my dchp client doesnt want to and gives me the error 1075.
I have removed NAV still nothing.

I have also tried many other alternatives but im just not remembering at the moment and I am just stumped.

Internet works on my other two computers, but my laptop is what seems to not want to connect wirelessly or routed. Something seems to be blocked or missing.

If anyone can please help me in any way possible it would greatly be appreciated. If you need me to provide some more details please let me know.

Thanks
Lewis B.
 

A:Error 1075/No Internet after Norton Anti Virus

16 more replies
Answer Match 55.86%

My computer (vista) was infected with a virus. So I first used rkill/iexplore then ran Malwarebytes Anti-Malware since my protection (Panda) doesn't seem to do its job correctly. The first time I did this, everything seemed to return to normal. Couple of days later, the same virus started up. I redid what I did...and it seemed to work again...until I tried using the internet. (I think Malwarebytes deleted something in the registry?)

There was an error saying that "DHCP error 1075: The dependancy service either does not exist or has been marked for deletion". I googled this on my laptop and followed some of the instructions found online. None of it worked...

I went into device manager->hiddle files->non plug and play drivers:
There was a problem with these with the same code for them: This device is not present, is not working properly, or does not have all its drivers installed. (Code 24)
App Filter Plugin
NetMon Filter Plugin
Panda Net Driver [TDI Layer]
VSCore mferkdk

Finally, I have included the last three logs from Malwarebytes showing which files were deleted by the program.

Thank you for looking over this!!

A:DHCP error 1075- Internet Doesn't Work

There is a dedicated forum for virus/malware issues regardless of your Windows version.
It's here: Virus/Trojan/Spyware Help - Tech Support Forum

(We aren't permitted to give virus removal help on the Windows forums)

2 more replies
Answer Match 55.44%

Avg found two trojans. It didn't seem like it removed them. Internet was working though. Ran malwarebytes it found nothing. Internet was still working. Started Having connectivity issues. My dhcp client service won't start. I got a 1075 error. my internet via wifi or wired. I ran the following command prompts:
net start AFD (response: the requested has already been started)
netsh int ip reset reset.log (response: resetting echo request, failed. Access is denied. Rebooting interface, ok! A reboot is required to complete this action.
netsh winsock reset catalog (response: successfully reset the winsock catalog. You must restart the computer in order to complete the reset.
SFC /SCANNOW (scan finishes and shows this response: windows resource protection found corrupt files but was unable to fix some of them. Details are included in the cbs.log windir\logs\cbs\cbs.log

What now? Please help.
 

A:Network issue dhcp client service error 1075

I'm thinking you're still infected.

----------------------------------------------------------------------

You need to start a thread in the Virus & Other Malware Removal section of this site.

Before you post though, you need to read THIS guide.
 

1 more replies
Answer Match 55.44%

I had a virus that would not allow me to get any icons, this was fixed after i ran avg in safe mode.

When i got back into the machine I received many pop ups one after another, ad-aware was run and after I cannot start any services, I have everything set to start in msconfig i have admin I cant change users, i cant do windows search, cant see any networks in network places nothing i cant even copy and paste the paste option is Grey when i try to copy then paste...

Every service I try to start i get error 1075 dependency service does not exist for all services.

also the Extended services tab give me nothing not list of any services only the standard tab.. I can click start and i get the error.

also Ad-aware gives me an error too when it tries to start system error 1810 has occurred service is not online.

Maybe i need to do a system restore i hope i don't lose all the pictures etc.. I cant copy and paste and its a laptop so i would need an adapter to put it on a desktop.. i think i will be OK with a system restore.

More replies
Answer Match 55.44%

I have a similar problem.... turn on print spooler, then go to add a printer and it says the print spooler is not running. round and round I go.

More replies
Answer Match 55.44%

This is really bad.. I cant copy and paste to backup files for reformat and this sony laptop is telling me that the recovery will delete all files, so no option to do a windows repair. I might need to buy a 2.5 to 3.5 adaptor for this mess im in, if you cant help.. I did many things so far nothing worked..

I had a virus that would not allow me to get any icons, this was fixed after i ran avg in safe mode.

When i got back into the machine I received many pop ups one after another, ad-aware was run and after I cannot start any services, I have everything set to start in msconfig i have admin I cant change users, i cant do windows search, cant see any networks in network places nothing i cant even copy and paste the paste option is Grey when i try to copy then paste...

Every service I try to start i get error 1075 dependency service does not exist for all services.

also the Extended services tab give me nothing not list of any services only the standard tab.. I can click start and i get the error.

also Ad-aware gives me an error too when it tries to start system error 1810 has occurred service is not online.

Maybe i need to do a system restore i hope i don't lose all the pictures etc.. I cant copy and paste and its a laptop so i would need an adapter to put it on a desktop.. i think i will be OK with a system restore.
 

More replies
Answer Match 55.44%

i have been fighting with this problem for ages.
my sound does not work, i dont know why, as far as i know, nothing was added before this started, everything was working, i got up the next day and there was no audio, it no longer registers my disc drive as being there, and i cant play an videos from youtube (other sites fine, though still no audio)
laptop tells me, theres no audio installed, but all drivers state everything present. tried on here before but with no luck

heres a run down from my last post:

i have no audio. if i click troubleshoot problems it says the audio service is not running
it says the windows audio and endpoint builder arent working
if i go into services, windows audio is set to automatic but its not on, when i click start it says "error:1075 the dependency service does not exist or has been marked for deletion"

medion akoya e6214 notebook
windows 7 64 bit sp1 home premium edition
intel core i3cpu [email protected]
4gb memory
2 ram i think
also, i have no system restore points, the windows repair disc doesnt work and i have no windows 7 install disc and cant burn one as my disc drive wont register

i have installed drivers for medion akoya as instructed but it did nothing

windows audio still states its not working, when i go to services, its set to automatic but wont stay on and i get the above error message!

im at my wits end, i cant back up anything so i dont lose it, cant restore, or repair, sfc scannow says i cant do it unless im admi... Read more

A:windows audio: error 1075 the dependency service does not exist or has

From your description there are many more problems than just the windows audio error.

I would suspect an Operating System problem. If you can find a friend to download the Windows 7 Home Premium ISO and burn it to a DVD, that would give you the needed disc to try and repair Windows. Although your DVD drive does not work in Windows, it should work for booting.

Here is the link to the forum post. There are links to the various versions. You can download the same version that you have.
Official Windows 7 SP1 ISO Image Downloads | Windows 7 Forums

4 more replies
Answer Match 55.44%

Hello,

On July 12th 2012, my computer installed updates. After rebooting and waiting for me on the login screen, I gave it a hard shutdown to check on the BIOS settings (for a little side project, in the end I did not save any changes). After booting and logging in again, I find that many services are not running. I ran a very thorough check for malware and viruses (took over 24 hours to complete), and still no solutions. I have uninstalled/reinstalled my Broadcom 802.11g Wireless Driver several times.
I now look in the Event Viewer and find that the DHCP Client service is not running! It is set to automatic start in Services.msc, but when I try to manually start it, it gives me error 1075 (some dependencies do not exist or are marked for deletion). Running ipconfig, I notice that my system is using an APIPA-formatted address (169.254.x.x), indicating that the computer couldn't find a DHCP server.

My Event Viewer is peppered with:
------------------------------------------------------------------------------------------------
Event 7003, Service Control Manager

The DHCP Client service depends the following service: Afd. This service might not be installed.
------------------------------------------------------------------------------------------------
Event 7001, Service Control Manager

The WinHTTP Web Proxy Auto-Discovery Service service depends on the DHCP CLient service which failed to start because of the following error: The dependcy service does not ex... Read more

A:DHCP Client Service FAILS TO START! (Error 1075)

It sure sounds like your computer is having its share of issues. Did you get the services started that you mentioned in your other thread?

7 more replies
Answer Match 54.6%

Hi when i try to run my windows XP sp2 windows firewall to stop it from disabling my connections. i get the message "Windows firewall cannot be displayed because the associated service is not running. Do you want to start the Windows firewall/internet connection Sharing (ICS) service?" i click yes then i get "Windows cannot start the Windows firewall/internet connection sharing (ICS) service.". i then went start>run>services.msc and found that when i try to manually run the Windows firewall/ICS i get this message "Could not start the WF/ICS service on Local Computer. Error 1075 the dependancy service either does not exist or has been marked for deletion." Please help me. I just want to be able to open my ports and host Warcraft 3 games.
 

A:Windows Firewall/Internet Connection Service cannot start...error 1075.

6 more replies
Answer Match 54.6%

Apparently something called print spooling is not working on my computer. I get error message 1075: the dependency service does not exist or has been marked for deletion. I believe this is why the installation won't go all the way to the end. The computer recognizes the printer but won't go ahead and finish installing it. Anybody got any suggestions?

A:Printer installation won't complete. Error 1075: the dependency service does not exis

Are you using Windows ME or Windows XP?

14 more replies
Answer Match 54.6%

Not sure why this problem is persisting. I appear to have all the dependent files. I have run SFC/ scannow to no avail. I cannot start the services in question. The 1075 error message continues. I have attached my system info.
 

A:Solved: DHCP client and TCPIP Netbios helper 1075 error

I was able to restart DHCP services by deleting the registry entry and rebooting. I went into the registry editor, located the DHCP subkey, right click on dependonservice and clicked on delete.
However TCPIP Netbios helper I could still not start, even after running sfc/scannow.
The solution for me was to restore the operating system to an earlier point in time. In windows xp, go to programs> accessories>disk utilities> system restore and follow the directions. I suppose I could have done that for both problems? At least I didnít have to reinstall XP!

Anyway I can connect to internet now
 

1 more replies
Answer Match 54.18%

After a Trojan attack, I used Kaspersky Virus Remover to remove them. It seems to have been successful, but now I can't access the internet.

Below are clues to resolving the problem. I just don't know what to do next.

Can you help? I'm using XP sp3.

=================

The following files are present in /Windows/System32/Drivers folder...
* afd.sys
* tcpip.sys
* netbt.sys (It was missing; so I copied to here from ServicePackFiles/i386)

=================

CMD /K SC QC DHCP reported this...

[SC] GetServiceConfig SUCCESS

SERVICE_NAME: dhcp
TYPE : 20 WIN32_SHARE_PROCESS
START_TYPE : 2 AUTO_START
ERROR_CONTROL : 1 NORMAL
BINARY_PATH_NAME : C:WINDOWS\system32\svchost.exe -k netsvcs
LOAD_ORDER_GROUP : TDI
TAG : 0
DISPLAY_NAME : DHCP Client
DEPENDENCIES : Tcpip
: Afd
: NetBT
SERVICE_START_NAME : LocalSystem

=================

In Device Manager,
* AFD Networking Support Environment is running successfully
* TCP/IP Protocol Driver is running successfully
* NetBios over Tcpip - DOES NOT EXIST

=================

In services when attempting to Start these services

* DHCP Client Properties (Local Computer) and
* TCP/IP NetBIOS Helper

I got these errors...

* Could not start the DHCP Client service on Local Computer
* Could not start the TCP/IP NetBIOS Helper service on Local Computer
* Error 1075: The dependency service does not exist or has been marked for deletion.
* Under the dependencies tab: No Dependencies in either box.

=================

Start, Run, SF... Read more

A:Cannot Access Internet after Virus Removal - Netbt.sys, NetBios missing - Error 1075

16 more replies
Answer Match 54.18%

Can someone please help, I can't connect to the internet whenever I connect it just connects local only and says the dhcp client isn't working on this computer when I go into services to manual start it says windows could not start the dhcp client on local computer error 1075 the dependency service does not exist or has been marked for deletion it happens on anyones internet I cant connect to wired and wireless, any help will be really appreciated as I have been trying to fix this for weeks now

A:windows could not start the dhcp client on local computer error 1075 the dependency s

Hello, lets do some cleaning up and see if that helps you out .
How to Flush DNS in Windows Using the Command Prompt

Step 1 ? Close all open web browsers and applications on your computer.

Step 2 ? Open the Windows command prompt by selecting the ?Start? menu and then go all programs, accessories, then right click command and run as admin.

Step 3 ? At the command prompt, enter ?ipconfig /flushdns? followed by pressing the ?enter? key. After a moment, Windows will display a message similar to: ?Successfully flushed the DNS Resolver Cache.? Once the message is displayed, the DNS will be flushed removing all incorrect entries.

Then , we want to get the IP reset, so, lets renew its settings and see if this also helps out :
you will type in the command box : ipconfig /release then enter, then next ipconfig /renew then enter, this will reset the IP , now restart and attempt to have it reconfigure its connections to your router. Post back results please.

3 more replies
Answer Match 44.1%

As of recently, I may have edited one registry after previously messing with a registry deletion using AVP cleaner. Now my LAN internet connection won't get past Acquiring Network and also my IP/Subnet are both 0.0.0.0 and my default gateway is blank. Someone please help me please
 

A:DHCP & TCP/IP getting #1075 Errors

16 more replies
Answer Match 43.26%

Recently purchased a new computer. I was having issues with installing Windows 7 and learned that HyperTransport is sometimes the cause of the issue and by turning it from "Auto" in the BIOS settings to "X1" can resolve the issue, and for me it did.

After installing Windows 7 and waiting to see if there were any other errors I went back to turn HyperTransport back to "Auto" I'm above computer savvy, but not far when it comes to hardware, I'm more of a software kind of guy. After doing so I was receiving consistent BSOD's. And after turning HyberTransport back to "X1" they went away narrowing it down to this being my issue.

I didn't know if updating my BIOS would help the issue so I decided to ask around first.

Computer Specs:

AMD Phenom II X6 1075T with HyperTransport
Gigabyte GA-870A-UD3
8Gig of Corsair Dominator
ATI Radeon HD 5770 1Gig

I have no idea about the power that any of these pieces should be receiving, nor if that would even be the cause of the problem. Also, windows freezes along with the BSODs saying that a video driver went out but was recovered, I just installed the latest video drivers. At the time of posting this the computer has been running for 2hours without HyperTransport set to "Auto"

Would updating the BIOS fix the problem?

Thank you!
 

More replies
Answer Match 26.04%

Try this link: http://support.microsoft.com/kb/836941
 

More replies
Answer Match 23.94%

I'm running Windows 7 Pro on my Dell laptop. This laptop has been in storage and hasn't been turned on in a year. Originally, all I wanted to do was use iTunes. The problem:
 
It made me update it in order to use it, but I got an error.
 
I un-installed it and tried downloading a fresh copy and I get the following error:
After some Googling, I read that not having the latest Windows .NET framework might be the problem. Sounded reasonable so I fired up Windows Update but that gave me an error and wouldn't start checking for updates.
 
I managed to get it to check for updates, but now when it starts the process, I get the following:
I Googled the error code "8007007E" and tried a few things to try and fix it.
 
I downloaded the windowsupdatediagnostic.diagcab, found on Microsoft's site, here:http://windows.microsoft.com/en-us/windows/troubleshoot-problems-installing-updates#1TC=windows-7
I tried resetting the Windows Update reset tool, using "MicrosoftFixit50202", found here:http://go.microsoft.com/?linkid=9665683
I download the system readiness tool, found here:https://www.microsoft.com/en-us/download/details.aspx?id=3132
I tried a clean boot.
 
I tried renaming the Windows Update Softwaredistribution folder.
 
None of this worked.
 
I ran the System File Checker tool (SFC.exe) and the results said I had bad files, but I don't know how to fix them. It generated a CBS log, which is too large for me to post (10MB) , so I've uploaded to dropbox,... Read more

A:Windows update error.. System File Checker integrity error..iTunes install error

Open the Command Prompt, copy and paste the commands below one at a time followed by pressing Enter after each command.
 
net stop wuauserv
 
rmdir /s %windir%\softwaredistribution\wuredir
 
net start wuauserv

9 more replies
Answer Match 23.94%

Symptom:
The URL of a shared folder on the LAN,  copied into Windows Explorer address bar produces the Network Error in the above title.
Network Error: WIndows cannot access
\\server.LAN.com\MySharedFolder   Error Code: 0x8004005 - Unspecified error.
But from a Dos terminal, Windows Explorer can open the same location just fine.  From DOS terminal:
start

More replies
Answer Match 23.94%

I had a very bizarre problem today. I downloaded about 50 .mpg files and put them into a folder on my desktop. I opened one of them, and it worked fine, but after that every time I even opened the folder that the files were in, only half of the thumbnails would appear and then it would tell me that I had a Visual C++ Runtime Error, from explorer.exe aborting. At the same time as this, windows would pop up a little message saying that my virtual memory was low. Later, it popped up a message saying that my Media Player needed to be reinstalled and that my Norton Antivirus needed to be reinstalled. Then it disabled my Norton Firewall and my Norton Antivirus. Lastly, I started getting error messages telling me that my soundcard needed to be configured to handle voice files, by enabling hardware acceleration. The only problem with that was that Windows would not let me access the advanced sound settings!

I am running Windows XP (all patches up to date), 256 MB Ram, 75 Gig HD - so I figured the "low" virtual memory had to be an error. I tried tripling the virual memory to 1GB and also tried letting Windows automatically set the virtual memory size, but neither of these fixed the problem. My immediate thought was that it was a virus or trojan, but Norton VirusScan, Swat-It Trojan Scanner, and System Suite VirusScan all failed to detect anything, and all of them have their definitions up to date.

I ran a Google search to see what other things I should try and none of the... Read more

More replies
Answer Match 23.52%

Ive just bought some new memory (TWIN2X4096-8500C5C G), the new memory doesnt seem to work unless I only add one stick, and even with that I get blue screen errors.

So from reading a few pages on teh internet I put my old memory back in, and ran windows driver verifier. Upon restarting I got and keep getting teh following BSOD.

IO SYSTEM VERIFICATION ERROR in wmiacpi.sys (WDM driver error 20e)

[wmiacpi.sys+152f at B7C5C52F]

A:Blue Screen IO Error. Verification Error In Wmiacpi.sys (WMD Driver Error 20e)

If the system ran fine...before you added RAM...then you need to see if the new RAM (by itself)...works.The new RAM may not be compatible with your old RAM, in which case the system will run fine with one or the other...but not both.The Driver Verifier tool is tricky to use, I would disregard that effort...for the moment.Remove your old RAM...put the new RAM in...see if the system works properly.FWIW: http://www.bleepingcomputer.com/forums/t/153175/blue-screen-io-error-verification-error-in-wmiacpisys-wmd-driver-error-20e/Louis

14 more replies
Answer Match 23.52%

The error onpage of Dell Start Page Trying to edit weather and the error message shows up. the error message is as follow: Line 2 Chasr 316 Error "HTML" is null osr not an object Code O URL HTTP:www google.com/IG/dell?HL=en&client=Del Would you send me an e-mail with the answer, please.

More replies
Answer Match 23.52%

I am getting a blue screen after I attempt to login to a pc.

Verification error in wmiacpi.sys (WMD driver error) 20e

wmiacpsi.sys = 152f at B9BAB852F

I have run the Dell diagnostic and everything passed.
This is a Dell laptop latitude D531. Dell just replaced the hard drive about 10 days ago. It worked fine until Monday.

Any any what this may be?

A:Blue Screen Io Error. Verification Error In Wmiacpi.sys (wmd Driver Error) 20e

Are you sure of the spelling of the 2nd file name? If so, Google doesn't give any results for it - which is suspicious.The first file name ( wmiacpi.sys ) is a Windows file that's used to help manage the ACPI settings in your system. http://www.bleepingcomputer.com/filedb/wmiacpi.sys-7763.htmlA BSOD error will usually point to the file that the error occured in, but this may not be the source of the error. Here's a link on how to find more info about the BSOD message: http://www.bleepingcomputer.com/forums/top...tml#entry409491Once you locate the .dmp files for the event, you can use this link to generate an analysis of the dump for us to have a look at ( http://forums.majorgeeks.com/showthread.php?t=35246 )

6 more replies
Answer Match 23.1%

I have got error 0x8007371 when I tried to install .netframework 3.5 which was required to install windows essentials.
I ran DISM command to fix 0x80073712 error, and received another error message in the command prompt: Error 14098 Component store has been corrupted.
THen I ran sfc/scannow which gave another error "An error occured during installation of assembly component".
This is such a bul grab, can someone help
Thankz

More replies
Answer Match 23.1%

Hey guys, having trouble getting XP to Update, well it did Update MSRT and failed on Flash as usual because I removed Flash.  The only thing I can think of that I changed was my Router settings to more aggressive, but it has not affected Windows 7?
 
This is the ms document on it: https://support.microsoft.com/en-us/kb/883820
 
I tried all the stuff they say there but none works.  I have SP3.
 
I am also being sent to this site, which don't look like it should.
http://windowsupdate.microsoft.com/
 
Thanks pcpunk

A:HTTP Error 500 - Internal Server Error, Error 0x8ddd0010

All good now!

1 more replies
Answer Match 23.1%

Hello there. I have been redirected here by jamanji, whom has been most helpful by the way.
My PC crashed a little over a week ago.
Rather than retype everything, I would like to give you the link to my post.
I am not 'Tech' per se, but I would like to try and resolve my problem myself,
To make a long story short... I had error 0xc000000f. I have 2 threads on the subject, but the first thread was useless.( I think)
I read gregrocker's tutorial.
I made a Kaspersky Disc. I have a Pop Up from Kaspersky.
saying if I continue...........

Here are the links.

confused by what type of disc to use

Error 0xc000000f

If you read this...Thank you for your time.

A:Burnt out from error error error! Time to go back to Paper.

Ok mate one thing straight up the Kaspersky only requires a CD you can use a DVD but seriously a waste of useable space. Have been using Kaspersky security and tis rescue disk for years now so just the CD mate.

Just follow the prompts when you run the disk. It will boot (of course) but will not need Windows to do anything.

There are other options -

Bootable AntiVirus Rescue CD for Windows: Free Download any are good and again do not require Wndows to run.

If you can get it going then I would try this
http://support.kaspersky.com/viruses/utility < the top scanner TDSS Killer

9 more replies
Answer Match 22.26%

Ok so my first problem was what I thought the sasser worm. I researched it online and I can't find any traces of it anywhere now. I ran a few spyware checkers and stuff and I think I may have messed with some registries.

Now I cannot access the internet and heaps of things are stuffing up. I disconnected my internet and upon startup get this.

A "Data Execution Prevention" window that closes "Generic Host Process for Win32 Services".

I press OK and that goes away. I found some suggestions online but none of them seem to work. That's my first problem.

My computer runs fine until I connect my internet. It runs alright for a minute or two before I get this error.

The instruction at "0x00401000" referenced memory at "0x00401000". The memory could not be "written". Which has recently been appearing at the same time as AVG saying a threat has been detected at "C:\WINDOWS\drivers\atimixx8.sys"

After this has come up I can press OK to terminate the stop error, or cancel to debug. Either one does nothing but stops my internet from working, and the internet on other computers in my house (we are all on a network). When I try to heal/move to vault/delete the AVG threat, it says I don't have permission.

I've thought about just formatting, but I have seen people who say that even with a format, the problem still persists.

Please help!
 

More replies
Answer Match 22.26%

My pc reboots for no reason when I try and access my network folders. I get the following errors in Event Viewer.


************************************************** ******

Event Type: Error
Event Source: ipnathlp
Event Category: None
Event ID: 31008
Date: 2004/11/10
Time: 07:33:55 PM
User: N/A
Computer: GIGS
Description:
The DNS proxy agent was unable to read the local list of name-resolution servers from the registry. The data is the error code.

For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.
Data:
0000: 6f 00 00 00 o...

************************************************** *******

Event Type: Error
Event Source: System Error
Event Category: (102)
Event ID: 1003
Date: 2004/11/10
Time: 02:40:01 PM
User: N/A
Computer: GIGS
Description:
Error code 00000051, parameter1 00000004, parameter2 00000001, parameter3 e12cfe18, parameter4 00008080.

For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.
Data:
0000: 53 79 73 74 65 6d 20 45 System E
0008: 72 72 6f 72 20 20 45 72 rror Er
0010: 72 6f 72 20 63 6f 64 65 ror code
0018: 20 30 30 30 30 30 30 35 0000005
0020: 31 20 20 50 61 72 61 6d 1 Param
0028: 65 74 65 72 73 20 30 30 eters 00
0030: 30 30 30 30 30 34 2c 20 000004,
0038: 30 30 30 30 30 30 30 31 00000001
0040: 2c 20 65 31 32 63 66 65 , e12cfe
0048: 31 38 2c 20 30 30 30 30 18, 0000
0050: 38 30 38 30 8080


**********************************... Read more

More replies
Answer Match 22.26%

Greetings!

I am having a problem with the above error message (error:syntax.error) when I'm running Firefox.

I have uninstalled Java and reinstalled it, but still the same problem.

OS Version: Microsoft Windows 7 Home Premium, Service Pack 1, 64 bit
Processor: Intel(R) Core(TM) i7-2670QM CPU @ 2.20GHz, Intel64 Family 6 Model 42 Stepping 7
Processor Count: 8
RAM: 8099 Mb
Graphics Card: Intel(R) HD Graphics Family, -238 Mb
Hard Drives: C: Total - 698475 MB, Free - 580394 MB;
Motherboard: TOSHIBA, PEQAA
Antivirus: avast! Antivirus, Updated and Enabled

Thanks,
Barbara
 

A:Error Message error:sytax.error - Firefox

See if you can find help here.

http://www.java.com/en/
 

1 more replies
Answer Match 22.26%

so i recently had this virus and someone on these boards helped me remove it. ty for that! but after 2 reboots it has come back..and with more errors this time like the explorer and drwatson. and also can you tell me why i have to do "open as" instead of just clicking on text documents? it says access is denied. i didnt do anything to get it again nor did i dl anything. anyway here are my logs any help is appreciated.
Gmer.txt
Hijackthis.txt
DDS.txt

A:Csrsc.exe error, Drwtsn32.exe error, explorer error

I have reasons to believe that you have a file infector onboard.
Please visit this website - http://virusscan.jotti.org
Submit the file for a comprehensive scan & then post the results back here.

C:\Windows\system32\cmd.exe

If it's virut, you need to wipe the machine immediately. Do not connect this machine to another one for you will infect that one too

7 more replies
Answer Match 22.26%

Just got a new computer and am trying to install my Philips Mini HiFi sytem. Contacted their support centre and they don't know what to do! The stereo system simply plugs into a usb port and plays your audio through their system. The only difference between the system it worked on a few days ago and now is that I am running Windows Professional x64.

The problem:

three things to install:

1. the Philips drivers. Philips support got me to download their drivers for Win XP.

When I install this the error rec'd is: "Install 2.15 setup. While installing drivers Plug and Play error detected. Please reboot and try again". I reboot and try again, same thing.

2. The program "Sound Agent" to run the show. When I install the Sound Agent program, the error rec'd is: "VDI32.exe has encountered a problem and needs to close".

3. MusicMatch to channel the audio through to it. (Seems ok but tells me it's out of date - no biggie I can deal with that).

In Device Manager there is "Unknown Device" listed under System Devices shown to be not installed (the yellow exlamation mark through it). When I try to Update Driver it says, "Cannot Install this hardware. The hardware was not installed because the Wizard cannot find the necessary software".

Finally, whenever I reboot I get the error message: "The QVE bus driver is not detected. Reinstall the Qsound Virtual Audio Devices Bus Enumerator driver".

I have reform... Read more

A:A Real Tough One. PnP error, VDI32.exe error and a QVE error. Help Please

Your link is not working, but many things don't have 64 bit drivers. Did the drivers say for XP or specifically for 64 bit?
 

2 more replies
Answer Match 21.84%

I am using a WD Proxkey DSC and while signing I am getting the following error"
"The Windows Cryptographic Service provider reported an error: The parameter is incorrect. Error Code: 2148073511"

More replies
Answer Match 21.42%

hi....
i have promblme , i do not know how to fix it..
i have kodak scnners i1220 plus
i have RD Web Access
the promblme is..
I have a system based on Oracle has been connted with one scanners( i connected with scanners) When i do a scan shows me this a message
(Scan Error Error while Scan::0::LEAD Error: Twain source manager no)
and
(Scan Error
Error while Scan::0::LEAD Error: Twain DS is connected to max possible apps)

Knowing that the scanner system has worked to windows xp but when we tray on Windows 7 does not work
why..............
i have pormission administrator and i setup the scnners drivers agine still same problme..
.......
i have windows 7 professional
service pack1
hp compaq 6200 pro MT PC
intel(R) core(TM)i5-2500 CPU @ 3.30GHz 3.29 GHz
4.00 GB
32-bit operating systme

A:Scan Error Error while Scan::0::LEAD Error: Twain source manager no

It's possible that TWAIN DSM is missing on your Win 7 machine. You can get it here and try again.

Catherine Sea
Dynamsoft: Provider of version control solutions & TWAIN SDKs

1 more replies
Answer Match 21%

Hey to all.
I am new to this forum and I want an answer with an ERROR.
My ERROR is "Fatal Error,NET_SendPacket ERROR : NO ERROR"(the same as title of the thread)
it occurs whenever i try to play counterstrike 1.6,counterstrike condition zero or half life 1 over LAN with another computer on the same network.But as soon as i start the game in this computer OR try to find any LAN server the Other PC which is the LAN server has this error and it exits the game on that computer only and as a result I get no LAN server.
I first thought of googling this error out but nothing worked out like the QoS uninstallation and tweeking the administrative tools>Local Security Policy.(honestly i just tried these two because i cold not understand or read any further)
Ohh and I have just re-installed the windows xp sp2 on this system.
If Any Additional Information is required please let me know.
So can anybody help me?
and please be simple i am not a geek or nerd ya know,so HOW?
 

More replies
Answer Match 21%

I've just install windows 7 home premium 64bit and got 4 times of BSOD.

for the first time error code is 0x0000001a
for the 2nd time error code is 0x0000003b
for the 3rd time error code is 0x0000003b
for the 4th time error code is 0x000000d1

I also attach minidump files and text files that I got from sf dianostic tool.



And another problem is I try to follow the instruction in this thread
How to fix BSOD caused by ntoskrnl.exe and ntkrnlmp.exe
and now I cannot start the normal window, I have to run in safe mode with network.



in the reply #4 that zigzag3413 post

Using Driver Verifier is an iffy proposition.
Most times it'll crash and it'll tell you what the driver is.
But sometimes it'll crash and won't tell you the driver.
Other times it'll crash before you can log in to Windows.
If you can't get to Safe Mode, then you'll have to resort to offline editing of the registry to disable Driver Verifier.

I'd suggest that you first backup your stuff and then make sure you've got access to another computer so you can contact us if problems arise.
Then make a System Restore point (so you can restore the system using the Vista/Windows 7 Startup Repair feature).

In Windows 7 you can make a Startup Repair disk by going to Start....All Programs...Maintenance...Create a System Repair Disc - with Windows Vista you'll have to use your installation disk or the "Repair your computer" option at the top of the Safe Mode menu .

Then, here... Read more

A:BSOD by ntoskrnl.exe, error d1, error 3b, error 1a

For now, I do a restore point and be able to run the normal window7.

1 more replies
Answer Match 21%

Hello there. Recently my computer have just randomly shutdown meanwhile i'm playing games like CS;GO, League of Legends. The screen will just turn black and it will start to make one hell of annoying noise untill it reboots.

I've updated all my drivers. Tested my memory. Tested my RAM. Run a virus scan. Checked the heat on my Graphic card and CPU. and all seems to work just fine.
This is the errors i get:


Code:
Log Name: System
Source: EventLog
Date: 25-12-2013 19:10:41
Event ID: 6008
Task Category: None
Level: Error
Keywords: Classic
User: N/A
Computer: Snaski-PC
Description:
The previous system shutdown at 19:08:21 on ‎25/‎12/‎2013 was unexpected.
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
<Provider Name="EventLog" />
<EventID Qualifiers="32768">6008</EventID>
<Level>2</Level>
<Task>0</Task>
<Keywords>0x80000000000000</Keywords>
<TimeCreated SystemTime="2013-12-25T18:10:41.000000000Z" />
<EventRecordID>2045</EventRecordID>
<Channel>System</Channel>
<Computer>Snaski-PC</Computer>
<Security />
</System>
<EventData>
<Data>19:08:21</Data>
<Data>‎25/‎12/‎2013</Data>
<Data>
</Data&... Read more

A:Error 41, Error 1001 and error 6008.

Hi Snaski.

It is some display/graphics related issue.

Are you overclocking? As you are getting BSODs, you should stop overclocking and run all the hardware components like CPU, GPU and RAM to their default settings.

Check if the Power Supply Unit (PSU) supplying adequate power to the computer or not.
eXtreme Power Supply Calculator
Also let us know the wattage of the PSU.

Stress test the Graphics Card using Furmark.
Video Card - Stress Test with Furmark
Let us see a screenshot of the furmark window, just before you close it.

Is the computer hot? Report us the heat of the computer after a couple of hours of your normal usage. Upload a screenshot of the summery tab of Speccy. Alternatively, you can publish a Speccy snapshot too: Speccy - Publish Snapshot of your System Specs .

Install the NVIDIA DRIVERS 314.22WHQL only.
Uninstall All nvidia items in Control Panel > Programs and features3D Vision Control Driver
3D Vision Driver
Graphics Driver
HD Audio Driver
PhysX
nvidia Update
(Are you using nvidia chipset drivers? If so, dont uninstall anything other than those are listed).
Now follow Drivers - Clean Left over Files after Uninstalling
Download 314.22 WHQL. While installing, Select Custom (Advanced) install. In the next page, follow this settings:
Let us know the results.
_____________________________________________________________________________________

Code:
*******************************************************************************
* ... Read more

7 more replies
Answer Match 21%

Hello,Ok so I have many issues with my laptop.First of all one day it failed and it was giving me the Hard drive not found (3F0) error.I decided to buy a new hard drive and still the same.Then I inserted a bootable usb (windows 7 pro 64bit) and tried to install windows.Then on the screen that I had to select the drive, the hard drive was shown.When I pressed to install windows a new error appeared. (ERROR CODE 0X8007045D).I devided to start over. Then again a new error appeared (Error 0x8004240f)I am really frustrated.What's wrong?Any advice?Thank you

A:3F0 Error, Error 0X8007045D , Error 0x8004240f

@ptheodoulou4abc? You need to partition the drive into one whole drive. You can use any free partition tool on-line. http://download.cnet.com/MiniTool-Partition-Wizard-Free-Edition/3000-2094_4-10962200.html REO  

9 more replies
Answer Match 20.16%

I have windows live mail 2008 Build 12.0.1606 installed on windows xp and everytime a few seconds after i close wlm i get a windows live mail encountered a ploblem and has to close error that tells me to send a report..this happens 80 percent of the time after i close the windows live mail application...By the way i have disable error reporting checked on advanced properties and disabled on services also ...i noticed on the task manager that the wlmail exe process is still running after i close the application and that seems to be the problem..Is there any way, fix or some program that i can get the wlmail.exe process to close at the same time i close the windows live mail application so i dont get this send error report message anymore ?

error i get ^

wlmail.exe still running after closing application ^

A:windows live mail 2008 (Build 12.0.1606) error report error

Hi gbp007,

Try to End Process the extra wlmail.exe file in the Task Manager Processes to see if it will stop the error for you next time.

Task Manager - Open and Close Applications and Processes

Shawn

13 more replies
Answer Match 20.16%

During Windows backup, which wants to backup the 'C' drive and my games drive 'E' (for some reason), I get the following error message after the 'C' backup has completed but not the 'E':

'The backup operation that started at '‎2015‎-‎12‎-‎20T06:00:25.459859400Z' has failed with following error code '0x8078012D' (The operation failed due to a device error encountered with either the source or the destination. If the source or destination volume is on a disk, run CHKDSK /R on the source or destination volume, and then retry the operation.). Please review the event details for a solution, and then rerun the backup operation once the issue is resolved.'

I ran CHKDSK \R and received several errors of the type: 'A disk read error occurred 0000185. The disk does not have enough space to replace bad clusters detected in file xxxxxx of name xxxxxx.'

My 'E' drive is 2TB with 205GB free. I really don't believe that the cluster(s) in error are bigger than 205G, but what do I know?

Anyone have experience with this problem?

Thanks.

More replies
Answer Match 20.16%

Hey guys, i want to thank you ahead of time for helping me.

This BSOD is a pain in the butt.

Intel Pentium 2.8GHZ
RAM 3.5
32 bit OS
Intel GG965 Express Chipset Family

I have already reinstalled the operating system multiple times, i think its a faulty graphics card, but i want to be 100% sure before i go and shell out the $$ for a new one

Please help The blue screen error points to igdkmd32.sys & it also says GRAPHICS_DRIVER_TDR_FAULT

A:BSOD error.. Restarts, but power button stays on, graphics card error?

STOP 0x00000116: VIDEO_TDR_ERROR (go to top of page)

Usual causes: Video driver, overheating, bad video card, ?BIOS, ?Power to card (see Significant Posts section below)

http://www.carrona.org/bsodindx.html#0x00000116

Incase you have overclocked your GPU reset it to the default.
Update your graphics driver to the latest stable version

1 more replies
Answer Match 20.16%

Agent.exe - Entry Point Not FoundThe Procedure entry point qsovt could not be located in the dynamic link library C:\Windows\SYSTEM32\apphelp.dll.I get this error whenever i try installing something new. I have a 128GB SSD that has my operating system, and a 3TB HDD that i use to store everything else in like movies, games, programs, etc.Whenever i try installing something, this error pops up multiple times, when i press "OK" it disappears and pops up again. It doesn't stop the program from successfully installing, but it's annoying. How do i fix this?

A:Agent.exe - Entry Point Not Found Error / Dynamic Link Library Error

It's for Forte's email client...and InstallSheild in some cases...

3 more replies
Answer Match 20.16%

This message now appears on an otherwise excellent computer.

Cannot connect to wireless broadband (I'm doing this on my Equium P200D)

Any ideas. I've tried the Toshiba help to no avail.

A:Qosmio E10 CFSServ Listen Error & Recv InitConnect Error appears on startup

Hi

Someone wrote in this forum that the CFSServ is part of ConfigFree utility.
Remove ConfigFree application from the system and try to use and configure your WLan again or try to use the LAN connectivity!

Check it out

1 more replies
Answer Match 20.16%

My System :
Windows XP Professional
Intel core 2 duo CPU T8100 @ 2.10GHz
1,99 gig of ram
Mobile Intel GMA X3100

My system sometimes restarts both in and out of games and so far have left these 2 events both 1003 and mini dumps as follows:

Event ID: 1003, Category: 102, Source: system error.

Error code 000000f4, parameter1 00000003, parameter2 87f91020, parameter3 87f91194, parameter4 805d297e.

Please help me, don't know what to do!
 

A:Random restarts -event id 1003 -system error- error code 000000f4

Your error is 0x000000F4: CRITICAL_OBJECT_TERMINATION
One of the many processes or threads crucial to system operation has unexpectedly exited or been terminated. As a result, the system can no longer function. Specific causes are many, and often best resolved by a careful history of the problem and the circumstances of the error message. One user, who experienced this on return from Standby mode on Win XP SP2, found the cause was that Windows was installed on a slave drive


The driver citted is crsss.exe and is an important part of your Windows OS.


See this link and read #2 to get some idea f what this driver does: http://www.liutilities.com/products/wintaskspro/processlibrary/csrss/


* It might pay you to do a security scan with your antivirus, etc.
 

1 more replies
Answer Match 20.16%

Hello,
 
Every time the computer reboots the message "GetEseDbInfo.exe has stopped working" appears. Checking for solutions yields no results.
 
Since this message has started:
 
- Windows search has quit working and states that "windows cannot access the specified device, path, or file. You may not have appropriate permissions to access them." 
 
- IE will only show a white screen and will not allow the tools option to be accessed. It keeps trying to recover and  cannot find any solution. Attempted downgrade to IE 9, re-install of IE10, use windows fix, and microsoft safety scanner.
 
-  Sticky Notes is unable to launch as it cannot access the file. 
 
I have run AVG, Advanced SystemCare, and Malware Anti-Malware but they all show up with nothing found. I don't know if these are all tied into together or are separate issues. 
 
The computer is a Windows 7 64bit operating system. 
 
Any help would be wonderful. Thank you!

A:GetEseDbInfo.exe error, IE White Screen, Search Access, & Sticky Notes Error

Open Task ManagerProcess (tab)Find GetEseDbInfo.exe, right-click and select "Disable"Reboot into Safe Mode with Networking. ADW CleanerPlease download AdwCleaner by Xplode onto your desktop.Close all open programs and internet browsers.Double click on adwcleaner.exe to run the tool.Click on Delete.Confirm each time with Ok.You will be prompted to restart your computer. A text file will open after the restart.Please post the contents of that logfile with your next reply.You can find the logfile at C:\AdwCleaner[S1].txt as well.   Last run ESET.Hold down Control and click on this link to open ESET OnlineScan in a new window.Click the button.For alternate browsers only: (Microsoft Internet Explorer users can skip these steps)Click on esetsmartinstaller_enu.exe to download the ESET Smart Installer. Save it to your desktop.Double click on the icon on your desktop.Check "YES, I accept the Terms of Use."Click the Start button.Accept any security warnings from your browser.Under scan settings, check "Scan Archives" and "Remove found threats" Click Advanced settings and select the following:Scan potentially unwanted applicationsScan for potentially unsafe applicationsEnable Anti-Stealth technologyESET will then download updates for itself, install itself, and begin scanning your computer. Please be patient as this can take some time.When the scan completes, click List ThreatsClick Export, and save the file to your desktop using a unique name, such as ESETScan. In... Read more

6 more replies
Answer Match 20.16%

I posted this earlier but reposted this and erased the old thread because I have more information now and have narrowed down the problem (I hope).This problem just happened yesterday after I had to manually shut down (used power button) my computer after it froze. Now when I try to load up IE, it "halfway" opens up (you can see parts of the interface) and just freezes. I thought maybe it was an IE problem, but if I try to load up Firefox (even without loading up IE first), nothing happens -- it won't load. I load up the Task Manager and firefox.exe is there as a process even though it hasn't loaded. The only way I did figure out to surf the net is to load up "My Computer" and enter a web address from there manually. But even when I do that, if I click on any link that opens up a new window, IE will try loading that new window up which freezes. Right after this happened, I get a "Generic Host Process for Win32 Services Error" (still do every now and then. I also d/l'd the "patch" for this from Microsoft's website to no avail) which says something about svchost.exe and some other exe's. I think it has something to do with networking because I loaded up "Event Viewer" from the Control Panel and I managed to track down the error I get *each* time my computer starts up These errors I get are *all* dated right after I had to manually shutdown the computer and when the problems began. Here it is:Source: DCOMEvent ID: 10005DCOM got e... Read more

A:Generic Host Process For Win32 Services Error / Dcom Networking Error -- Help!

Hi and welcome to Bleeping Computer! My name is Sam and I will be helping you. Please download ComboFix and save it to your desktop.Double click combofix.exe and follow the prompts.When it's done running it will produce a log for you. Please post that log in your next reply.Important Note - Do not mouseclick combofix's window whilst it's running. That may cause it to stall.

12 more replies
Answer Match 20.16%

I dont know how this started but i need major help please.... When I turn on my computer I receive an AutoIt Error, Line -1, Something went wrong with " Object" and when i dismiss the warning later on I receive Data Executive Win32 Prevention Errors and memory reference errors. I have read alot of forums for help. I have ran malware programs, virus scans, etc.... No luck its just getting worse and slowing down my computer and now I get a blue screen when I try to boot up in safe mode and the drivers loading screen comes up. What do I do?

I read the instructions for posting this type of post, and I have attached the logs requested.



.
DDS (Ver_2011-08-26.01) - NTFSx86
Internet Explorer: 8.0.6001.18702
Run by patesag at 16:03:47 on 2012-06-08
.
============== Running Processes ===============
.
.
============== Pseudo HJT Report ===============
.
uStart Page = hxxp://bakerhughesdirect.com/
mStart Page = hxxp://search.searchonme.com/
uInternet Settings,ProxyOverride = *.local
BHO: AcroIEHlprObj Class: {06849e9f-c8d7-4d59-b87d-784b7d6be0b3} - c:\program files\adobe\acrobat 7.0\activex\AcroIEHelper.dll
BHO: DivX Plus Web Player HTML5 <video>: {326e768d-4182-46fd-9c16-1449a49795f4} - c:\program files\divx\divx plus web player\ie\divxhtml5\DivXHTML5.dll
BHO: PlusIEEventHelper Class: {551a852f-39a6-44a7-9c13-afbec9185a9d} - c:\program files\nuance\pdf professional 7\bin\PlusIEContextMenu.dll
BHO: Groove GFS Browser Helper: {72853161-30c5-4d2... Read more

A:AutoIt Error, Data Prevention Win32 Error, and Memory Reference Errors.... Help!!!!!!

When the drivers loading screen comes up during safe mode boot the computer goes to a blue screen. I never faced this problem before. Please help....

19 more replies
Answer Match 20.16%

no matter how many times i clean the drive it will still come up with this error. i can't figure out what is going on. i am able to convert the movie just fine but when it comes times to write to blank dvd, it won't do it. this is the problem i am having on my laptop which i will include the log. for some reason on my pc the program convertxtodvd doesn't even acknowledge that i have a dvd drive , i believe it is the pcouffin, which i have uninstalled and reinstalled but i cannot get it to work. it says it is working fine but device no longer available. well here is the log from my laptop which will convert but will not finish the copy.

2/20/2008 1:29:47 AM info ********** Report session closed ***********
2/20/2008 1:29:30 AM error BURN: Write error at 0 (16) - Code 03 73 03 [Medium error, Power calibration fail (CD-burner is dirty)]
2/20/2008 1:28:14 AM info BURN: Write started 894784 sectors to write
2/20/2008 1:28:14 AM info BURN: Writing speed requested x4.0, effective x4.0
2/20/2008 1:28:13 AM info BURN: Available write speed: 8x, 6x, 4x, 2.4x
2/20/2008 1:28:13 AM info BURN: Media ID: SONY-D21-00
2/20/2008 1:28:13 AM info BURN: Media type: DVD+R
2/20/2008 1:28:13 AM info BURN: Multiword DMA Mode 2
2/20/2008 1:28:11 AM info BURN: Scanned files #8, folder #2 - total size 1831393280 b. (1.71 Gb.)
2/20/2008 1:28:11 AM info BURN: Inserted media type : DVD+R
2/20/2008 1:28:11 AM info BURN: Write started
2/20/2008 1:28:10 AM info --------... Read more

A:Write error at 0 (16) - Code 03 73 03 [Medium error, Power calibration fail (CD-burne

Replace the laptops burner... Laptop/notebook CD/DVD R/W's are very delicate and are more subject to failure than desktop writers
 

3 more replies
Answer Match 20.16%

Hi All
system info : HP LAPTOP DV6 -1256tx , windows vista sp1 32 bit
When I am trying to install windows vista sp1 from recovery disks/partition I am getting the error from recovery manager prompting me to choose either to retry or see the details for failure : CTOERROR.flg in form of notepad on my desktop. I have done retry 100 times but to no avail. I cannot restart after this recovery failure message as it shows dialog box on restart: windows security update is not installed successfully or is not trusted.So, i have to go through recovery process again to see the desktop (everything functioning - internet,video, music all) but only once.
Last time i got this message too . When i did installing windows from recovery disks few months back, that time i figured out to install all imp. updates through automatic windows update.All the updates were installed successfully and then it restarted and gone through process of language settings,time settings and all....
But this time when i am trying to update windows, i am getting windows update error 0x643 which is for security update for .net framewrok 3.5 sp1 and family update.I do know the answer how to get away with this error from "windows help" and also from this forum too, which asks for installing .net framework updates from windows update site directly. But the problem is:
Windows update ask me to restart after automatic or manual windows update installation takes place and restart causes problem as it shows d... Read more

A:Windows vista recovery error CTOERROR.f​lg and following that error 0x643 while insta

Do you have the original (no SP1 or SP2) Vista installed? You won't be able to install SP1 otherwise.

7 more replies
Answer Match 20.16%

Stop: c0000221 unknown Hard Error /system/system32\ntdll.dll

I get the above error while i try formating my computer. i restart my pc then i boot up xp cd, then it loads, and gets to say Starting Up Windows, cd stops, then goes black then blue and ntdll.dll error. Another error

Missing Operating System

I get this error when i try to start my computer.

I am using a compaq laptop......Please help me out.

A:Stop: c0000221 unknown Hard Error /system/system32\ntdll.dll ERROR

Hello ,

what you need to do is erase the harddrive then do the reinstall , you can get a free program that you can create a bootable cd to do this with from here

(http://www.majorgeeks.com/Dariks_Boo...uke_d4596.html)

or you can download the tools to do this from the manufacturer of the harddrive

either way you will have to make the bootable cd

make sur you read the instruction on the way to use the program

then start your system then put in the cd / reboot to load the cd and then erase your drive

depending on the size of your dive this can take from 1 to 5 hrs

this will write the drive to zero's and make it as if it never had software install on it ( like new from the factory)

Mike R.

2 more replies
Answer Match 20.16%

I am trying to install cakewalk SONAR 7 and I get this error when running the installation and start the small window on "c++ 2005":

"Error 1935. An error ocurred during the installation of assembly
'Microsoft.VC80.ALT.type="win 32", version="8.0.50727.762", publickey Token="1fc8b3b9a1e18e3b", processor Architecture="AMD64". Please refer to help and support for more information."
-------------------------------------

When I checked the event viewer, I have a Vista application event ID 33, with the description below,

"Microsoft.VC80.MFC,processorArchitecture="amd64",
publicKeyToken="1fc8b3b9a1e18e3b",type="win32",version="8.0.50727.762"
Could not be found. Please use sxstrace.exe for detailed diagnosis."
--------------------------------------

When I try to run the sxstrace.exe, I have then this message (the error message is in blank.):

"C:\Users\Xxxxx Comp>sxstrace parse -logfile:sxstrace.elt -outfile:sxstrace.txt
Parsing log file sxstrace.elt...
ProcessTrace failed. Error message is:"


I been google this problem and try different approaches for the last 3 days and nothing fix this problem. I try to install microsoft visual c++ 2008 and c++ 2005 and have similar errors.
Any help in this matter will be highly appreciated, right now is a "dead end"...

Thanks, guys in advance for the help in this matter...

A:"Error 1935. An error ocurred during the installation of assembly 'Microsoft.VC80.AL

Hi,

Just to confirm for us, install the Visual C++ redist 2005, then VC++ redist 2005 SP1, then VC++ redist 2008, then VC++ redist 2008 SP1. Only restart PC after last one has finished and do them in order, one at a time. This will take quite a long time, let them finish. Then run windows update and select everything, in particular the updates for the VC++ redists (mainly security updates) and restart PC again. Tell us if anything here fails and any error messages you get. Are any of your applications getting side by side configuration errors? Then try your program install again. Hopefully it will now work. Tell us what happens. Will try and post links later as this post sent off iPhone.

Hope this helps, though you may have already done this.

Richard

P.S. You could try sfc /scannow though I really doubt it will help.

EDIT:

Here are the web addresses in the correct order:

http://www.microsoft.com/downloads/d...displaylang=en

http://www.microsoft.com/downloads/d...displaylang=en

http://www.microsoft.com/downloads/d...displaylang=en

http://www.microsoft.com/downloads/details.aspx?familyid=BA9257CA-337F-4B40-8C14-157CFDFFEE4E&displaylang=en

2 more replies
Answer Match 20.16%

I get all those messages at start up, plus superfetch has stopped working, and sometimes windows explorer has stopped working. I know it's some type of virus from something. So far safe mode has been working (slowly). Yesterday I had a friend reinstall(?) vista on it so I'm not sure if it would qualify as a legal copy or not anymore but it was actually much worse before that. It couldn't even start up right normal or safe mode.

it is a hp G60t-200, and the OS is vista, I'm not sure what other info would be needed for this. Please help if you can.

More replies
Answer Match 20.16%

I posted this earlier but reposted this and erased the old thread because I have more information now and have narrowed down the problem (I hope).

This problem just happened yesterday after I had to manually shut down (used power button) my computer after it froze. Now when I try to load up IE, it "halfway" opens up (you can see parts of the interface) and just freezes. I thought maybe it was an IE problem, but if I try to load up Firefox (even without loading up IE first), nothing happens -- it won't load. I load up the Task Manager and firefox.exe is there as a process even though it hasn't loaded. The only way I did figure out to surf the net is to load up "My Computer" and enter a web address from there manually. But even when I do that, if I click on any link that opens up a new window, IE will try loading that new window up which freezes. Right after this happened, I get a "Generic Host Process for Win32 Services Error" (still do every now and then. I also d/l'd the "patch" for this from Microsoft's website to no avail) which says something about svchost.exe and some other exe's. I think it has something to do with networking because I loaded up "Event Viewer" from the Control Panel and I managed to track down the error I get *each* time my computer starts up These errors I get are *all* dated right after I had to manually shutdown the computer and when the problems began. Here it is:

Source: D... Read more

More replies
Answer Match 20.16%

Edit: Think my hard drive may be failing and was the cause of my file synchronizing crash. I use it mostly to stream music and video and access the hard drive a lot. Any advice thanks

HDDStatus - Tool to check hard disk status, health and reliability

Hey,

I've been using GoodSync for the past couple of months to chain synchronize 3 hard disk drives and ran into my first issue today. GoodSync stopped responding whilst synchronizing changes to files so I used task manager to manually end the process.

I'm not entirely sure how much damage has been caused but when I re-analyzed the file changes a lot of the changes prior to the crash was no longer listed.. So I'm unsure of the file integrity but have so far noticed some music video files are corrupt with cyclic redundancy check errors but is not easily visible to check corrupt files because they still play but parts of data are missing.

I think I've experienced cyclic redundancy check errors before when my external hard drive fell flat on it's side whilst it was playing music (3 years ago). It took me a long time to filter out the bad files because all the mp3 files worked but some songs would randomly play in others etc.. is their some type of automated CRC scanner or method to check all my files ?

Thanks

A:Error copying file: Data error (cyclic redundancy check). CRC Scan ?

If you are able, try this programme, it is VERY good. HDD Regenerator - Dmitriy Primochenko Online

1 more replies
Answer Match 20.16%

Help, can't print anything and can't find out how to fix that error code

A:Printer Spooler has a error message <Failed to Read Description. Error Code: 193 >

Hi, go to start search and type:- cmd, right click on the returned cmd.exe and select "run as administrator" at the prompt (copy paste)


Code:
sc queryex spooler > 0 & notepad 0
(press enter) I am guessing we will see error 1058.

Next still at cmd type:-


Code:
net start > 1 & notepad 1
(press enter)

Please post both notepad entry's here.

4 more replies
Answer Match 20.16%

Hi,I have fundamentally the same problem as Laura H from this thread http://www.bleepingcomputer.com/forums/topic342716.html.I've had problems with these fake antivirus programs before and they really did a number on my laptop. I treated the problem using various tools mostly malware bytes and deleting some suspect files.Been working fine for the most part however today out out of nowhere I was attacked by malware doctor. I deleted the suspect file from the temporary internet files folder and ran malware bytes that detected trojan and deleted. Shortly after drwatson ??? was shut down and some time later I think explorer shut down because my desktop went back to basics....no theme,desktop wallpaper etc. the windows 95 look if you grasp what I'm trying to get at. I thought it was no big issue and in my own time restarted laptop when I realized audio wasn't working after trying to play a film.Upon restart I get the blue screen with the same message as Lauras. So for the most part I'm in the same situation as Laura with some minor differences such as I didn't use Spy doctor etc.I have Kaspersky AV installed which has been inefficient in protecting my laptop lately, especially from these fake AV attacks. I am using Windows Firewall which I know is a bad idea.Myrti was helping Laura resolve the issue and I have followed her instructions upto the following actions:'locate this file and right click it > choose rename > rename it to userinit.txtnow we wi... Read more

A:Malware doctor infection removal and then error c000021a (fatal system error)

Hello,Please follow the instructions in ==>This Guide<==. If you cannot complete a step, skip it and continue.Once the proper logs are created, then make a NEW TOPIC and post it ==>HERE<== Please include a description of your computer issues and what you have done to resolve them.If you can produce at least some of the logs, then please create the new topic and explain what happens when you try to create the log(s) that you couldn't get. If you cannot produce any of the logs, then still post the topic and explain that you followed the Prep. Guide, were unable to create the logs, and describe what happens when you try to create the logs.Orange Blossom

6 more replies
Answer Match 20.16%

I did tried to update an old modem about a week ago and ever since I cannot connect to the internet. I have two laptops and works fine. I have a wireless set up.

I just tried plugging in the Ethernet connection to the laptop to no avail. Still no connection.

Info:

HP Compaq nc6230
Wireless setup

I tried connecting to other unsecured wireless networks in the area and still was not able to access the internet.

Please help.

Thank you.
 

A:Laptop cannot connect to Internet - DNS Failure, Gateway Error 0x2afc, Error 12007

8 more replies
Answer Match 20.16%

Hi,

I've been having Kernal data inpage error which I assume is from a faulty harddrive (or maybe the RAM?!). I occasionally get a disk check during bootup, which didn't seem to help. I was saving up to buy a hybrid SSD/HDD drive before replacing it, but now it seems a bit too late.

Yesterday after a windows update, I rebooted my computer and the desktop was running very slow, nothing would open, explorer.exe would crash, I would be stuck in desktop until I force shutdown by holding the power switch (Shutdown didnt work), after doing this once or twice, I now get a BSOD again with a registry error right after the desktop loads for 1-2 seconds. X051 error code I think.

What step should I take now to diagnose the problem?
Thanks!
 

More replies
Answer Match 20.16%

I have an Acer 6920, Vista, and I have taken the following actions after the computer would not boot:
a. ordered reinstall disk from Acer
b. reinstalled the system using the four disk
c. worked with computer normally for three weeks
d. encountered the original problem again of not booting
e. tried to go back to factory settings using the reinstall disk from Acer
f. after 65%, encountered the 0XD00000A error
g. tried again, and encountered the same error

Is this a Vista problem, an Acer problem, or something that happens often?

Any help would be greatly appreciated.

More replies
Answer Match 20.16%

Hello, i am having a problem i get
Stop: c0000221 unknown Hard Error /system/system32\ntdll.dll

What im trying to do is formating my computer i restart my pc then i boot up xp cd, then it loads, and gets to say Starting Up Windows, cd stops, then goes black then blue and ntdll.dll error. I tryed reisntlaling windows, overwiritng file, please help!


(i have readed all the posts about this error to but that didn't help in my case.)

A:Stop: c0000221 unknown Hard Error /system/system32\ntdll.dll ERROR

Quote:





Originally Posted by oshwyn5


Xceltron: It really would be helpful if you kept it all in one thread and told us all your symptoms.
I see you have more than one thread as well as asking for help in someone elses thread. THis makes it very hard to follow.

http://www.techsupportforum.com//mic...ard-error.html


http://www.techsupportforum.com//mic...ard-error.html

http://www.techsupportforum.com//mic...any-files.html



Let me start with analysis of this error.
http://aumha.org/win5/kbestop.php




If you are getting this error when trying to reinstall from your XP cd, then it sounds like you have a loose damaged or incorrect cable to either your cdrom or hard drive. I suggest replacing them both with quality 80 wire 40 pin IDE cables. It can also be caused by incorrect configuration if you have RAID or SATA drives.
Finally you may want to try with just one stick of RAM installed. If you have more than one now; you should try each in the slot nearest the processor all by itself until you rule out one of them being bad (If it works with one stick and not the other, you know the other is bad).

There is more information on possible causes of this error at ahuma ; but my first suspicion on seeing the image checksum mismatch is that the file in question has been replaced with something else, a trojan or virus.

Please download
Mcafee stinger multivirus removal tool
Install and run

Spybot search and ... Read more

9 more replies
Answer Match 20.16%

First my machine specs:

http://www.evga.com/community/ModsRi...asp?sysid=5160

Im using Windows 7 Ultimate x64.

Im having some issues with my computer freezing, this occurs while using a "patcher" to download content to a mmo game and sometimes while playing 3d games.

My event viewer has this all the time:

--------------------------------------------------------
A corrected hardware error has occurred.

Reported by component: Processor Core
Error Source: Corrected Machine Check
Error Type: Generic Cache Hierarchy Error
Processor ID: 0

The details view of this entry contains further information.
--------------------------------------------------------

[ Name] Microsoft-Windows-WHEA-Logger
[ Guid] {C26C4F3C-3F66-4E99-8F8A-39405CFED220}

EventID 19

Version 0

Level 3

Task 0

Opcode 0

Keywords 0x8000000000000000

- TimeCreated

[ SystemTime] 2010-04-20T19:25:49.490400000Z

EventRecordID 5406

- Correlation

[ ActivityID] {954A60D4-EFE5-4F8B-B054-8D11A7E15C9D}

- Execution

[ ProcessID] 1488
[ ThreadID] 2096

Channel System

Computer blabla-PC

- Security

[ UserID] S-1-5-19


- EventData

ErrorSource 1
ApicId 0
MCABank 3
MciStat 0x9020010c0320100e
MciAddr 0x0
MciMisc 0x0
ErrorType 7
TransactionType 256
Participation 256
RequestType 256
MemorIO 256
MemHierarchyLv... Read more

A:A corrected hardware error has occurred, Generic Cache Hierarchy Error

Please provide this information: http://www.techsupportforum.com/f217...ns-452654.html

Although you haven't mentioned any BSOD's, the info will provide us with some details so we can try to figure this out.

In general, a machine check is related to an error that's recognized by your CPU and reported to Windows. There's not usually much information in the error reports so we have to fiddle around trying to figure it out.

Most often these are either hardware problems (something's busted) or compatibility issues (either software or hardware).

1 more replies
Answer Match 20.16%

Mod Edit: Moved from Win8 to the Am I Infected forum ~~boopmeI randomly decided to look at McAfee and check my settings, etc.  When looking at the main screen, everything states its on and green.  I had the most current definitions loaded.  When I checked my McAfee firewall it stated on.  When I clicked to go into the McAfee firewall, the screen then changed and said it was off.  When clicking the Turn On button, it would immediately shut off.  I searched this issue and the blogs stated to look at the Windows Firewall under Services.  When I checked, it was not there.  I did a Windows Search for it and found it.  When it opens it gives tells me I need to Update the Firewall Settings.  When I click on Use Recommended Settings it gives me an error "Windows Firewall can't change some of your settings.  Error Code 0x8007042c." I've checked out some of the blog discussions and followed a few thread about creating new register.bat files and running them.  I've also tried merging some .dll files also per the bloggers.  After doing these actions, the Windows Firewall now appears in my Services but when I click to start it I get the error "Windows could not start the Windows Firewall Service on Local Computer.  Error 1068:  The dependency service or group failed to start"

A:Can not start Windows Firewall - Error Code 0x8007042c and Error 1068

McAfee has verified I have a virus.  Will post in the Virus Forum.

15 more replies
Answer Match 20.16%

I'm running a Windows XP Pro system, 2gb good RAM, AMD Athlon 64 3500+, nVidia GeForce 9800 GT. I attempted to install a copy of Oblivion (which I have had and used many times in the past). The disk is in very good condition, and can be used on another machine. I have tried it on multiple drives for this one PC, but now, it will not complete the loading of the InstallShield Wizard. It gives me this error:

Error Code: -5006 : 0x80070001
Error Information:
>SetupDLL\SetupDLL.cpp (1194)
PAPP:Oblivion
PVENDOR:Bethesda Softworks (http://www.bethsoft.com)
PGUID:35CB6715-41F8-4F99-8881-6FC75BF054B0
$11.0.0.28844

I have searched for a solution online, but have not found one that works yet. Any suggestions?
 

More replies
Answer Match 20.16%

I am using Windows 7 Home Edition 64-bit.

Hi there,

I installed MS Office Home and Student 2007 and it installed correctly with no errors.

After installing, I tried opening it in Start>All Programs>Microsoft Office>MS Word (and the other program shortcuts in the same list) and an installer window popped up and then I got this:



Solutions I have tried: I did a registry scan with CCleaner and Registry Mechanic to try to fix some corrupted .dll files, thought maybe it would help, but it didn't.

I also went to the MS Office folder in Program Files and opened the .exe files and that also would not work. (It told me I did not have enough memory to run this program, but I have 2x 1 TB HDD and 12 GB of RAM.)

- I am lost as to why it will not work...

A:MS Office 2007 Install Error - Error 25004 Config.Xml not specified A valid...(etc

Quote:





Originally Posted by Endlessly


I am using Windows 7 Home Edition 64-bit.

Hi there,

Solutions I have tried: I did a registry scan with CCleaner and Registry Mechanic to try to fix some corrupted .dll files, thought maybe it would help, but it didn't.




First of all this forum does not support Registry cleaners of any flavor as in this link for your information. Not even the registry option in CCleaner is wise in my opinion.

Are you sure you mean 12GB RAM on this system?Right click My Computer on your desktop
Properties
Please post back the information showing thanks....

I would suggest you run sfc/scannow, reboot and if no improvement, my only suggestion is to uninstall and reinstall MS Office Home and Student 2007.

You can use Revo uninstaller to do the above if you choose to do so, as I think it is a better utility than Add and Remove/Programs and Features in Windows 7.

My comment is I hope running those registry options has not damaged your OS.....

Let us know thanks..

kind regards,

6 more replies
Answer Match 20.16%

Hey,
 
Got this posted on a few other forums, so i'll just copy + paste it and list what i've tried so far.
 
SUMMARY OF PROBLEMS
 
UPDATE: The main problem at the moment seems to be linked with the Inetcpl.cpl in C:\Windows\System32
 
- Cannot open Internet Explorer: When I open IE 9, the process appears, and internet explorer starts up. As soon as the tab for my homepage loads, IE closes straight away, and leaves behind the download manager for IE, asking me if i want to download my homepage.
 
- Cannot open Internet Options through control panel: When i go to Control Panel > Networking > Internet Options and click on it, nothing appears on screen, no matter how many times i press it. Same thing happens with IE > Tools > Options; nothing appears
 
- Cannot open Skype (I found this was linked to the IE problems): When I open Skype, the login page stays on a white screen, and i am unable to click anywhere on skype / close it, I have to force close it by ending the process (Temporary solution found, look below)
 
- Cumulative Security Update for IE 9 won't install (Windows Update): This has been an on-going problem for around a year+ now, but still relevant. Whenever my Windows Update has a Cumulative Security Update for IE 9, I try to install it, however it fails and says updates were not configured correctly, reverting changes The error code I get is: 800719E4. As far as I am aware, there is no solution to this er... Read more

A:Internet Explorer + IE Options Issues / Inetcpl.cpl Error / Skype Error

I know it's not a virus problem, I have a clean system at the moment, I think it'll be more appropriate in the Vista forum

4 more replies
Answer Match 20.16%

Hello I keep getting this 3 errors (Error Code 0x8007042c, Error 1068 and (-5001 : 0x80070002), after installing:

Update for Windows 7 for x64-based Systems (KB2607576)

and

Update for Windows 7 for x64-based Systems (KB2603229)
Although both updates installed successfully I keep getting this errors since today when I installed those updates here are some pics:

http://i1178.photobucket.com/albums/...ewallerror.jpg

I cannot start windows firewall

not even from here

http://i1178.photobucket.com/albums/...artuperror.jpg

and I can't install games either

http://i1178.photobucket.com/albums/...stallerror.jpg
Help me please Is my computer ruined? I will provide all the information you need but please help me fix it I couldn't find any solutions on Google so please help me, I'm begging you

I cannot do a system rollback since it says there were no restore points but I could do a rollback before, I've uninstalled those updates also but the problem persist

A:Error Code 0x8007042c, Error 1068 and (-5001 : 0x80070002) after insta

Anyone? I'm really scared by the fact that my firewall does not work That means my computer is vulnerable

9 more replies
Answer Match 20.16%

Hi guys,

I was using my computer today and for the first time ever (had computer for 10 months) I had a BSOD. Here is what I found. Anyone have any thoughts?

FAULTING_MODULE: 81c00000 nt

DEBUG_FLR_IMAGE_TIMESTAMP: 0

WHEA_ERROR_RECORD: !errrec ffffffff849784e0

BUGCHECK_STR: 0x124_GenuineIntel

DEFAULT_BUCKET_ID: WRONG_SYMBOLS

STACK_TEXT:
WARNING: Stack unwind information not available. Following frames may be wrong.
81ceef84 81fa6f1f 00000124 00000000 849b3578 nt+0xd8681
81ceefa0 81cced6a 849b3578 84ac2de8 00000001 hal+0x5f1f
81ceefc0 81fa6ede 84ac2de8 84ac2f00 81ceeff4 nt+0xced6a
81ceefd0 81fa6fff 00000003 84ac2de8 00000000 hal+0x5ede
81ceeff4 81fa389f 8014a000 00000000 00000000 hal+0x5fff
00000000 00000000 00000000 00000000 00000000 hal+0x289f


STACK_COMMAND: kb

FOLLOWUP_NAME: MachineOwner

MODULE_NAME: hardware

IMAGE_NAME: hardware

BUCKET_ID: WRONG_SYMBOLS

Followup: MachineOwner

A:windows vista bsod STOP error (error posted)...any thoughts?

Quote:





Originally Posted by ajcool123


Hi guys,

I was using my computer today and for the first time ever (had computer for 10 months) I had a BSOD. Here is what I found. Anyone have any thoughts?

FAULTING_MODULE: 81c00000 nt

DEBUG_FLR_IMAGE_TIMESTAMP: 0

WHEA_ERROR_RECORD: !errrec ffffffff849784e0

BUGCHECK_STR: 0x124_GenuineIntel

DEFAULT_BUCKET_ID: WRONG_SYMBOLS

STACK_TEXT:
WARNING: Stack unwind information not available. Following frames may be wrong.
81ceef84 81fa6f1f 00000124 00000000 849b3578 nt+0xd8681
81ceefa0 81cced6a 849b3578 84ac2de8 00000001 hal+0x5f1f
81ceefc0 81fa6ede 84ac2de8 84ac2f00 81ceeff4 nt+0xced6a
81ceefd0 81fa6fff 00000003 84ac2de8 00000000 hal+0x5ede
81ceeff4 81fa389f 8014a000 00000000 00000000 hal+0x5fff
00000000 00000000 00000000 00000000 00000000 hal+0x289f


STACK_COMMAND: kb

FOLLOWUP_NAME: MachineOwner

MODULE_NAME: hardware

IMAGE_NAME: hardware

BUCKET_ID: WRONG_SYMBOLS

Followup: MachineOwner




Hi. . .

A bugcheck of 0x00000124 = 0x124 indicates that a fatal hardware error has occurred. The reference to WHEA is Windows Hardware Error Architecture. There is an event log for WHEA, under Applications and Services\Microsoft\Windows\Kernel-WHEA. It usually contains entries stating that WHEA was successfully initialized, that x# error sources are active and the record format of WHEA. I have never seen any other entries in it b... Read more

2 more replies
Answer Match 20.16%

I took apart my computer so I could build my new one, but the new motherboard was bad. I put my old computer back together and I get a 02b0: Diskette A error. I am not 100% sure the pci devices are in the same slots as they where before and I am not sure if I have HD, CDR, DVD, and TapeBack plug back in the same order I had them. Does anybody know what this error message means??? I need help asap. Below is a list of some basic info

Windows 2000 on Gateway G6-450 PII w/ 256 ram, 16.8 hd, 20gb tape back up, DVD player, CD-RW, 56k modem, lan card, scsi card, voodoo 3, sb512, and external zip. Email me directly if you have any good ideas. I am using my laptop that is luckily running win2000 with no problems but need the computer us asap.

Thanks
Robert Ward

 

A:{Moved from NT/2000 Forum} - Boot Error - 02b0 Diskette error

Sounds to me like you didn't plug the floppy drive back in correctly. If the cable is backwards the drive won't work for instance.

Is the tape drive IDE or is it on the floppy controller too?

------------------
Get free stuff and help out a poor computer tech
(4/29 free $5 added - free computer headset extended to 5/31!):
http://www.rkfdcore.com/ebaypics/referrals.htm
 

2 more replies
Answer Match 20.16%

Hi
 
I copied some files from my old HP laptop with xp, burnt them with burnaware onto a dvd. Now on my new laptop (lenovo g580 W7 64bit) I tried to take them off the DVD and move to my local drive, when I was moving them from disc to drive explorer gave me a message saying 'Invalid MS-dos function' and the usual try again or cancel option.
 
Thinking some of the files on disc might be corrupt I ran
 
xcopy F:\*.*/s > C:\test1
 
And got the message in my topic title File creation error - Data error (cyclic redundancy check).
 
Now I don't have clue what this means and I can only tell you I have an output file in C, as per the command instructions, with almost all the files listed, some are missing but some of the ones there are the corrupt ones and some of the ones missing I think are fine.
 
Doesn't really lead me to the issue unless someone can decipher the error message I got?
 
Thanks
 
Andrew
 

More replies