Tech Problem Aggregator

Router configuration problems

Q: Router configuration problems

For some time now, my home LAN has been experiencing some problems. The router (an ss2624 speedstream wireless) sometimes doesn't want to work, (or most of the time) and sometimes it does. I have three computers connected to it, and they all can access the router's web page. However, none of the computers recieve internet access.

One of my computers is able to connect the the cable modem directly and receive internet. I use all the numbers I see from running winipcfg on my directly connected computer when I setup the router, but for some reason the router will not work. I make it so that it uses a static IP address from the ISP (which I'm not entirely sure even is static, even though I always see that same IP address, I also see a DHCP server number) and also I put the DNS server I see, although I am able to choose between 4 different numbers. (I put the others as alternate.) Am I missing any information from my ISP?

A: Router configuration problems

Set your router back up to receive DHCP if your ISP requires it. Sometimes ISP's use private IP's for you, that conflict with your current router config. If your router IP is 192.168.1.1, then make sure the IP that you get from your ISP is not 192.168.1.(1-254) Earthlink is bad about this. If it is the case, just change your router (inside address, not the external ISP address) to 192.168.10.1 or something other than 192.168.1.1 just change the second to the last number to anything else.

Not the best at drawing a mental picture here. but

If WAN address is 192.168.1.1
and router is 192.168.1.1 , they conflict. Plus the router needs a different network like 192.168.2.1 for you to be NAT'd

Hope this helps.

2 more replies
Answer Match 63%

Hello everyone.
I just acquired a tablet (Transformer Prime) and wanted to add another wifi router to my network connection as a way to increase the signal on my room. I tried following the instructions on this Linksys help article:
http://www6.nohold.net/Cisco2/ukp.aspx?pid=80&login=1&app=search&vw=1&articleid=4579

I've tried the first method described and completed all steps and still couldn't connect the second router. when i connect both by the ethernet socket only the first one, unaldutered, worked providing internet access to my PC by wire but the second one didn't increased reception on the tablet at all.
Ipconfig shows no sign of any other device besides the working router when they are connected by the ethernet socket. When i connect only the second router ipconfig reveals there is no "Connection-specific DNS Suffix" and "Default Gateway". I cant change options back to normal in the web browser because i dont have a default gateway number anymore

What have i done wrong? how can i fix this and configure this damn router to give me my precious wifi speed?
Any help would be appreciated and I'm verry sorry for the long and badly explained post (im a noob with pcs, to say the least)

BTW: first post, but I'll introduce myself later on a proper post
 

A:Problems with second router configuration

Reset the second router to factory default settings and try the following procedure. It is the same as your linked article Option 1, but maybe it will be easier for you to follow.

JohnWill's procedure (Aug. 30, 2008) for configuring a secondary router as a switch and, optionally, wireless access point follows.

Connecting two (or more) SOHO broadband routers together.

Note: The "primary" router can be an actual router, a software gateway like Microsoft Internet Connection Sharing, or a server connection that has the capability to supply more than one IP address using DHCP server capability. No changes are made to the primary "router" configuration.

Configure the IP address of the secondary router(s) to be in the same subnet as the primary router, but out of the range of the DHCP server in the primary router. For instance DHCP server addresses 192.168.0.2 through 192.168.0.100, I'd assign the secondary router 192.168.0.254 as it's IP address, 192.168.0.253 for another router, etc.

Note: Do this first, as you will have to reboot the computer to connect to the router again for the remaining changes.

Disable the DHCP server in the secondary router.

Setup the wireless section just the way you would if it was the primary router, channels, encryption, etc.

Connect from the primary router's LAN port to one of the LAN ports on the secondary router. If there is no uplink port and neither of the routers have auto-sensing ports, use a cross-... Read more

1 more replies
Answer Match 61.74%

OK, I'll give a brief overview of what I'm working with and then describe my problem. I have a relatively new notebook (bought it about 2 months ago, I wouldn't think the exact specs are necessary but if they are let me know), a DSL connection and I have a Linksys Wireless-G router.

I've attempted to play two games online with a friend (Age of Empires 3 and Diablo 2), both of which resulted in nothing by headaches. In both games we attempted to directly connect to each other via IP. He also has a notebook and is using a wireless router. We've tried it both ways; me trying to connect to him and vice versa, same problem both times.

Now, I don't know a whole lot of anything about networking and routers and the such, but I'll put in what I do know. When I try hosting a Direct IP game, both games listed an IP at the top of the screen, but it wasn't my IP, it was what I think is called the local IP? It's 192.168.1.1; now I know that's the address to the router and if I type that in my browser address bar I can access the router's configuration and all that good stuff. I also noticed that if i go to that address one of the options under the router configuration is "Applications and Gaming". When I go there it lists a bunch of stuff about opening ports and triggering ports and some other stuff that I've never heard of.

I've talked to a few people and they tell me that I would need to open certain ports and... Read more

A:Online Gaming/Router Configuration Problems

7 more replies
Answer Match 53.76%

Hello Everyone,

I just wanna ask for some help regarding configuration of a vpn firewall router that is connected to a 4g modem/router combo.
I am new in setting up a vpn and not so much familiar with others things or what setup is necessary, kindly help the poor guy please???

This is what I need:
- I need to connect the VPN FIREWALL router and use its features at the same time connected to the internet ( the VPN FIREWALL will act as the security for the whole network and the 4G modem/router will be the one supplying the internet)
- Need to establish a VPN connection later after the configuration.
- The server and other lan pc's must be accessible outside the local network when connected to VPN (web server, local pc's shared folder and files, etc)

Here's some details that i hope might help:
- I am using a Quanta 1K5 4G LTE modem/router combo
- I am using a Dynamic public IP address,( but this is not a problem because i am using s DDNS)
- My VPN FIREWALL brand/model is Micronet SP881 B VPN FIREWALL router
- Right now i am already connected to the internet using the vpn firewall physical connection is:
4G modem/router-->hub-->VPN firewall router-->PC
my connection is 4G(LAN)-->VPN (WAN) set the connection type to Dynamic IP
-The remote connection and remote access (web server, ftp,RDP) is working fine on the 4G modem/router alone.

I attached some screenshots of the VPN firewall router
Looking forward to hear from you guys, Thanks in advance!
&nb... Read more

A:HELP! 4g modem/router combo to vpn firewall router configuration

7 more replies
Answer Match 48.72%

I am attempting to set up servers for various games on my PC. The only problem is the my system connects to the internet through a (wireless) router and others (non-LAN) cannot connect to me. I have read many articles on opening router ports and configuration settings but it is all too confusing for me to figure out and i dont want to screw up my low-latency connection! Does anyone know how to make this work?
 

A:Router Configuration

Go here
and find your router and it has good instructions to set up port forwarding. They might even have the game you use listed.
 

2 more replies
Answer Match 48.72%

I am trying to configure my router so that it will play Asheron's Call. I went onto portforward.com and my router is Linksys WRT54Gv6. I go to the default IP address for configuration and when it asks for my password/username, none of the ones that were given (i.e. blank or admin) work in any combination. I was wondering if anyone would know how to find out this information for this model/version or if there is another way to port forward the ranges 9000-9001, 9004-9005, and 9012-9013? Thank you!
 

A:Router Configuration

6 more replies
Answer Match 48.72%

I currently use a router with my isp connection through the cable provider in my area .The problem I am experiencing is when the computer is plugged DIRECTLY into the cable modem provided by my isp, bandwidth(via speed test) is at expected speeds .
(cable modem is a thompson dhg574)

HOWEVER once the router(dlink DLR-645) is plugged in to the cable modem the bandwidth essentially cuts in half (@7mbps)or more of the 20mbps service I subscribe to.

I know that the router can be successfully configured because it was set up in the past but I no longer have the information to do it anymore.


Tech Support Guy System Info Utility version 1.0.0.2
OS Version: Microsoft Windows 7 Home Premium, Service Pack 1, 64 bit
Processor: Intel(R) Core(TM) i3 CPU M 370 @ 2.40GHz, Intel64 Family 6 Model 37 Stepping 5
Processor Count: 4
RAM: 7988 Mb
Graphics Card: Intel(R) HD Graphics, -325 Mb
Hard Drives: C: Total - 476837 MB, Free - 395883 MB;
Motherboard: Dell Inc., 08VFX1
Antivirus: Microsoft Security Essentials, Updated and Enabled
 

A:router configuration help

11 more replies
Answer Match 48.72%

hi,

could anyone please let me know the router configuration steps.
 

A:router configuration

best place to look is in your router's user guide.
 

3 more replies
Answer Match 48.72%

I want to configure a wireless router on my compute

steps taken

wired conn- run the cd-put user/password and with wired connection I am able to go on line and once I am taking out the wire from the laptop it shows "page cann't dispaly"

A:router configuration

and welcome to the Forum

See how much this helps your understanding of networking:

http://www.homenethelp.com/web/howto/net.asp

1 more replies
Answer Match 48.72%

I would like to access my router to configure it for maximum internet connection speed. The router is a NetGear WGR614v4 with both wireless and hard wire connections . My operating system is Windows XP Professional and I use a cable high speed interenet service. My router is out of the warranty period and NetGear will not provide tech support.
 

A:Router configuration

14 more replies
Answer Match 48.3%

Hey guys i was wondering if you could help me Port forward and or Proxy my Wi-Fi router.... Im using a TP-LINK WR340G.. really need help.
 

A:Wi-Fi router proxy configuration help

Port forwarding has these requirements

the machine to which the forward will point to must have a static IP address
once port(s) are so configured, NO OTHER system will be able to use those ports.
(1) can be done manually on the target system, or more easily in the router by using IP Address Reservation.

Pg 33 of the manual describes (1)

Pg 34 describes the setup for port forwarding
 

3 more replies
Answer Match 48.3%

My Internet cable is rj45. If i connect that cable directly to my pc, and set up the connection (PPPoe, requires a username and pass), i can access the internet.
then i bought a tp-link wr841n router which has a Wan (rj45) i/p socket.
and i ran the tp-links setup software, configured the router with the username and pass, but still it wont connect to the internet.
and help please ?
 

A:Solved: Router configuration

6 more replies
Answer Match 48.3%

Hi, I am actually trying to configure a router, with a serial and fast ethernet interface..
now i have a network address of 192.168.50.1 and i have used 192.168.50.2 for the fast ethernet interface and 192.168.50.3 for the serial interface, but it giving me an error, saying its overlapping the fast ethernet address of 192.168.50.0, is there anything i'm doing wrong there? can anyone help me please...
 

A:Hi everyone i have router configuration error...

6 more replies
Answer Match 48.3%

I have a (hopefully rather basic) problem with the configuration of my new D-Link router DIR-657.

Now, what I had in mind was rather simple, but apparently I don't know the correct settings to
achieve it... (A lack of knowlegde on my side, I guess. I have some experience setting up simple
networks with a few windows computers and broadband modems, but the last time was some
time ago and this one here seems to be a bit more complicated than I thought...)

I have one PC (Win7 Ultimate 64) with a 3G modem (via USB) and want to use this computer (PC1)
and the 3G connection to act as the internet connection (using ICS) for my home network.
This computer now connects to the new D-Link router (via LAN).
I want to use this router to connect the other devices in this network (LAN/WLAN) with PC1 so they
can also use this internet connection (via ICS) and also for the other basic network uses (file sharing,
printing, ...).
The setup of ICS was not a problem (I think) and the local network (LAN/WLAN) is working alright,
but how do I have to configure the router so he "knows" that all internet traffic is going through the
3G connection (ICS) at PC1 (LAN port) and not its WAN port (which is empty) while maintaining
the functionality of the network (file sharing, printer,...) of course.

[FYI... I want to use PC1 (with 3G) for my internet connection because I want/need the VPN
connection I have installed on this PC. While there are a few (WLAN-)router out there that can
hand... Read more

A:ICS + LAN/WLAN Router configuration

9 more replies
Answer Match 48.3%

Hi guys!
I have a Wireless Router,Belkin F5D7230-4 Router.
Model: F5D7230-4 - Data Transfer Rate: 54 MBps - 2.4 GHz - Wireless Connection.

1)Previews we changed default ip address 192.168.2.1 to some thing.But now I forgot that default page ip address.How to get that page.I restarted that back side button.But it is not getting.Can any one any one?

2)How to configure it?

Thanks for Apperication.......
 

A:Wireless Router configuration

Hold the reset button for about 15 seconds. After that you should be able to use the 192.168.2.1 address to get back to the config page
 

1 more replies
Answer Match 48.3%

How can I find all the companies ip address for setting up wireless router? For example, Netgear, Linksys Dlink, and other compamies.
Thanks!!!!!
 

A:configuration of wireless router

How can I find all the companies ip address for setting up wireless routerClick to expand...

do you mean what default gateway they use
ie 192.168.0.1
or
192.168.254.254
etc

you could look in all the manuals - a lot of routers manuals are on the manufacturers sites - it would also give you the default username and password

why are you after so much info???
 

1 more replies
Answer Match 48.3%

I recently purchased and installed a Linksys RT31P2 wired router while converting to Vonage VoIP. I installed the RT31P2 behind an Actiontec GT-701 DSL Gateway (modem/router). I plugged a telephone into the RT31P2 and my VoIP phone service works great. Because my Actiontec GT-701 DSL Gateway only has 1ea Ethernet port, I had to remove my local computer from the Actiontec Ethernet port so that I could connect the RT31P2 to the same Ethernet port. After removing the local computer from the Ethernet port on the Actiontec GT-701, I moved it an open Ethernet port on the RT31P2. The local computer has Internet access and appears to work normally accept that it can no longer file or print share with the other computers on my home network. Prior to this change, I had 3ea wireless NIC-connected computers and the Ethernet-connected local computer configured onto my local network via the Actiontec GT-701 DSL Gateway. All of these computers were configured to file/print share and did so successfully. After the installation of the Linksys RT31P2 router, the local computer can no longer file/print share with the 3ea wireless NIC-connected computers. I have some basic networking knowledge and I understand that by adding the Linksys RT31P2, I have essentially created two networks. The problem appears to resolve around the fact that there two networks are currently not able to properly communicate in a manner that will allow file/print sharing between them. Is this problem solvable utilizing ... Read more

A:Multiple Router LAN Configuration

16 more replies
Answer Match 48.3%

I have 6 units of PC and i have 2 Internet Service Provider (ISP).

Using a dual WAN Router, how can i configure it to have my 3 PC connected to 1 ISP and the other 3 PC is connected to another ISP.
ISP 1 >>> >>> 3 Computers
>>> Dual WAN Router >>> Switch/HUB
ISP 2 >>> >>> 3 Computers
Just thinking if it is randomly get an access to net. If there is a way to configure or assign them on which connection them will be pls. guide me.
If can't get my illustration i will make a better one. ^_^

hmMm... and does this settings can connect my 6 Computers with each other? So, that i will have an access to them? Or in use of LAN Games or File sharing?
p.s.

what is the disadvantage and advantage of this settings?
 

More replies
Answer Match 48.3%

Hey all,

Not sure if I'm in the right forum. A couple months ago I had to switch providers, and had to get hooked up with a wireless router. Ever since then, my download speeds have crash landed.

I'm running XP. Any tips on where to go for help would be appreciated.

thanks!
 

A:need help with wireless router configuration

What bandwidth are you supposed to be getting?

What speeds do you get with a test such as Speakeasy connecting by wireless, by ethernet to the router and directly to the modem?
 

1 more replies
Answer Match 48.3%

I have a WNDR3700 connected to a wired network that I access through wireless. When I get pretty far away from the WNDR3700 I loose the ability to connect and I was thinking if I could extend the wireless network by adding a DAP-1522.

I want to have the WNDR3700 and the DAP-1522 connected via wireless and using a laptop I want to be able to access the wired network from anywhere in the facility.

Can this be done and could you guys tell me step by step how to do it, I will definitely appreciate.
 

A:Router plus Bridge Configuration Help......

Hi,

For best performance is good to have cable installed between WNDR3700 and d-link access point at remote location. All those repeaters, extenders and wireless distribution systems affects wireless performance.
 

3 more replies
Answer Match 48.3%

Hi folks,

Glad to be on board, this website came highly reccommended by to me by some fellow members of a Boston Red Sox fansite, and I must say, the info here is great.

I finally have a question to ask:

Recently, I set up a pretty complete wired home network so that I could work from home more often. In so doing, I added two laptops and another desktop to my office, which used to house just a single desktop. They are all connected to my cable modem through a router.

Over the past several months, my partners and I have been using AIM and MSN Messenger's talk programs (I believe this is called Voice-over-IP, is it not?) pretty regularly throughout the day to stay in touch.

When the single PC was connected to the internet without a router, these programs worked easily and flawlessly. Now, as the four PC's are connected to the internet through the router (and are therefore behind the router's firewall??) I can not use either application for voice conversations on any one of the four PC's. Simply put, they will not establish a connection to my peers on the other end.

I am now on my second router (switched from D-Link to Belkin). The tech support from both companies has been horrible, and neither has been able to help me connect using these apps at all. They are all pretty sure that I will eventually need to open the correct port or ports, and will need to configure the router accordingly, but none of them seems to know how to do so themselves, and as suc... Read more

A:Router Configuration Problem(s)

i think you have open the ports in the router setup,have a look in your manual
mine come under advanced features,coference and telephony
 

2 more replies
Answer Match 48.3%

My computer wouldn't wake from sleep mode a few days ago so I hard rebooted it. When it booted I no longer had internet access.

My local area connection was listed as an unidentified network with no network access. I used the troubleshoot tool on the connection and it returned "the router does not have a valid IP configuration". I could not change the network from public to home/private.

I am able to connect to the internet using the same router and cable on this laptop. The wireless is also working fine.

I have tried:
disabling and enabling the network adaptor, DHCP and the local connection
updating the network card drivers
disabling ipv6 in local connection
Resetting the router to factory settings
I disabling bonjour (I do not have and have never installed mcafee)
clearing the TCP/IP stack with netsh int ip reset
using ipconfig /release /flushdns /renew
system restoring to before the issue occurred
doing a clean install of windows (it saved my old files under windows.old - I assume this is still a clean install)

I am running windows 7 home premium 64, my network card is an Intel 82567LF-2 Gigabit, the router is a Thomson TG782T and I am using Bigpond ADSL2+.

It's been a couple of days and I'm well out of my depth. I didn't expect the issue to continue after a clean install. Any help would be really appreciated. Attached is the ipconfig I get. Attachment 288972

A:Router does not have a valid IP configuration

If you could attach your ipconfig please because I can't see it

This can help us determine possible causes

Josh

9 more replies
Answer Match 48.3%

Hi,

Been having problems with my router today, was working fine and then all of a sudden dropped out.With a notification that the Modem wasn't working. I plugged in my laptop via Ethernet to Modem and it worked as fine.

Contacted my ISP and they said it was the router just broke, therefore I purchased another Router today, to my disbelief, still the same problem,can connect via ethernet but not WLAN.

Devices will connect locally but not to the internet.

Any ideas?

Thanks, Russ
 

A:Help needed with Router Configuration

is this all wireless devices cannot connect to the internet
and thats with two different routers

whats the make and models of the routers

is there a modem involved ?
if so make and model

do a power cycle - see below

------------------------------------------------------------------------

How to power cycle

“power cycle” process to reboot or reset the modem/router

Switch off all the devices modem, router and computers also unplug their power cables.
Wait at least 1 to 5 minutes. We have found in some instances you need to wait at least 15 minutes
Plug the power cords back in, but don’t switch them on.
First turn on the modem and then wait for a few minutes for it to settle and all the lights to become stable.
Next switch on the router (if a separate device) and then wait for a few minutes for it to settle and all the lights to become stable.
Now turn on your computer, You should now be able to access the Internet.
------------------------------------------------------------------------
 

3 more replies
Answer Match 48.3%

I recently bought a NetGear Router to setup my lan to use internet access to more then one PC. I finally got everything working fine. However, I am curious on what is PPPoE use for?

Could some one tell me what this is use for and what it means.

Thanks in advance.
Charlton
 

A:NAT with PPPoE Configuration on router???

9 more replies
Answer Match 48.3%

Is there any security benefit (extra firewall, etc) from using two routers to connect to the internet. For example, this computer connects to port 1 on my Netgear. From the WAN port, a wire connects the port 4 of my Dlink. The WAN port of my DLink connects, of course, to my modem and the Internet. second question...how do I access the secondary router. Anytime I type in "192.168.0.1", I only access the DLink interface. (I was confused about configuring the Static IP on the secondary Netgear so I left it as is) Any ideas/ suggestions. Can I somehow use this dual router to my benefit?

I have a Netgear (RP614) and DLink (DI 714P+). Networking has always somewhat eluded me, and I was wondering what benefits/unique configurations may be derived from two routers.

Here is the setup.

Thanks in advance

-R
 

A:Dual Router Configuration

6 more replies
Answer Match 48.3%

In the past, I could access my routers set up by typing in 192.168.0.2 as the address in my web browser. Now I am not able to access the set up window. I have connectivity to the internet and everything has been working just fine. I usally go into the configuration to turn on and off the wireless portion of my router. The router is a netgear VPN. Can someone please assit with this issue. Thanks!
 

A:Can't Access Router Configuration

13 more replies
Answer Match 48.3%

Hi everyone, new here. I've just got a buffalo airstation WZR-1750HP and i cannot for the life of me configure it for internet access. I have entered my isp username/password but still no joy. I must admit i'm utterly hopeless with networking, but not bad with other computer matters. Hoping some wireless whizz kids can tell me what my settings must be.

A:router configuration woes

Dual band AC routers can be tricky as they sometimes are not compatible with older wireless N clients.

Best to upgrade any wireless n NIC's to AC NIC's if they can't connect consistently.

Also depends on if there are any other routers in the network, or if the modem is a modem/router or just stand alone modem, not enough information here for me to give directions.

2 more replies
Answer Match 48.3%

I am using an edimax 3G-6200n router with a 3G usb modem on the '3' network to connect to xbox live. I can connect easily and play most games and join most partys but sometimes i cannot join certain friends games and matchmaking is slow on some games such as modern warfare 2. I have tried DMZ and UpNp on the router but the NAT remains strict. Any help would be greatly appreciated. Thank you.
 

A:Edimax router configuration

Do not open multiple threads on the same topic. You already have replies here.
 

1 more replies
Answer Match 48.3%

I have been dealing with the same issue for the last couple months. I only need the router because I use my cable connection for TiVo. I am going to try your instructions.
 

A:Router configuration issues

11 more replies
Answer Match 48.3%

I sent over a Linksys DIR-615 router to a friend in Venezuela as he does not have any wireless internet, now from my understanding and what he has explained he has a modem to router connection already, however the router does not have wireless.

He got the router today and I told him to replace his current router with the one I sent him. Now the connection going from his modem to router wouldn't work in the WAN port. So we placed it in LAN ports along with his two PCs and great, he got internet on both computers but he can't access the router configuration to set the wireless.

Now I made sure it all worked before I sent it, I replaced the router I have at home with it and it worked with the IP 192.168.0.1
However when he enters that it doesn't bring him to the router configuration, nor with 192.168.1.1, 192.168.1.2, 192.168.0.2 and some others.

So I told him to use ipconfig to get the gateway IP and trying to use that to access the router, but still it won't work.
The Ipconfig looked like:

Adaptador Ethernet Conexión de área local :

Sufijo de conexión específica DNS : cantv.net
Dirección IP. . . . . . . . . . . : 201.210.21.98
Máscara de subred . . . . . . . . : 255.255.224.0
Puerta de enlace predeterminada : 201.210.0.1

So basically I have come here in search for help on how I can get to the router configuration and enable the wireless for them.
Anything you ask I can ask of him and report back.

Thanks in advance!
 

A:Need help with router configuration connection.

So.is there a default gateway listed in the ipconfig above ?
And you said linksys.Did you mean d link ?
Is the ISP cable or dsl ?The setup would be different I believe.
Might be a good idea to go back to basics,just to make sure that everything was done in the correct order.Like so.
Tips on setting up broadband connection, courtesy of Johnwill

You don't need any setup disk to configure a broadband router.
. The following procedure should get you a connection with any broadband modem that is configured to use DHCP for the router connection, such as cable modems, and many DSL modems. If you require PPPoE configuration for the DSL modem, that will have to be configured to match the ISP requirements.
• Turn off everything, the modem, router, computer.
• Connect the modem to the router's WAN/Internet port.
• Connect the computer to one of the router's LAN/Network ports.
• Turn on the modem, wait for a steady connect light.
• Turn on the router, wait for two minutes.
• Boot the computer.

When the computer is completely booted, let's see this.

Hold the Windows key and press R, then type CMD (COMMAND for W98/WME) to open a command prompt:

NOTE: For the items below in red surrounded with < >, see comments below for the actual information content, they are value substitutions from the previous command output!

In the command prompt window that opens, type type the following commands one at a ti... Read more

3 more replies
Answer Match 48.3%

Hi I have a D-Link DSL 604+ Router and modem conected to a 2mb broadband connection which works fine appart from me only getting 2kbs download speeds when using bittorrent. I have been told that this may be because i have not configured some ports on my router? Is anyone able to help me solve this problem Please
 

A:D-Link Router Configuration

Won't get much help with this issue due to the function of bittorrent....I doubt it is your router, however

http://forums.techguy.org/faq.php?faq=vb_read_and_post#faq_faq_p2p
[tsg=welcome]to TSG![/tsg]
 

1 more replies
Answer Match 48.3%

I am running a Netgear WGR614V5. I can connect fine to the internet and everything using the tourer but I cannot connect to the router configuration page. I did have a password setup on it, but I was connecting to it earlier today fine. For some reason the reset button does not seem to be working. When I ping 192.168.1.1 none of the packets are received. When I put in ipconfig /all this is what comes up.
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Unknown
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
DNS Suffix Search List. . . . . . : hsd1.mi.comcast.net.

Ethernet adapter Local Area Connection:

Connection-specific DNS Suffix . : hsd1.mi.comcast.net.
Description . . . . . . . . . . . : CNet PRO200 PCI Fast Ethernet Adapte
r
Physical Address. . . . . . . . . : 00-08-A1-31-A0-97
Dhcp Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
IP Address. . . . . . . . . . . . : 68.41.138.90
Subnet Mask . . . . . . . . . . . : 255.255.252.0
Default Gateway . . . . . . . . . : 68.41.136.1
DHCP Server . . . . . . . . . . . : 68.87.77.13
DNS Servers . . . . . . . . . . . : 68.87.77.130
68.87.72.130
 

A:Router Configuration - 192.168.1.1 Not Working

8 more replies
Answer Match 48.3%

my xbox 360 online runs through my pc i've just changed to a wireless connection for my pc and now my xbox wont regester with my pc sayin it doesn't hav th ip adress and tells me to go to my router configuartion web page where do i find this?
 

A:router configuration web page

9 more replies
Answer Match 48.3%

hi there. my name is fred and i heard about a router configuration panel that people with routers for their dsl and cable internet connections. is that true? if it is how do i get to it. i heard of one way but it doesnt work. i know my router/cable modem is from rca. and i know my ip address. since i dont know how private that is i will just leave it at that. any help??
 

A:router configuration panel????

The router configuration panel differs from brand to brand. Linksys, for example, has a default of 192.168.1.1, with a blank username and 'admin' as the password. DLink routers use 192.168.0.1.

Do you know what the IP of your router is?
 

2 more replies
Answer Match 47.88%

i have netgear FVS336 dual wanport vpn router. one wan port is connected to my company server through vsat and having static ip and gatway. second wan port is connected to isp dsl modem which is having dynamic ip. now i required configuration to use both wan ports same time. please help me
 

More replies
Answer Match 47.88%

I've been trying to solve this problem for over 4 months now by myself so any help would be appreciated. I don't like asking without trying to solve and search for this by myself first, but I just can't do it

Setup:
- Desktop Computer (works fine when directly connected)
- Laptop Computer (works fine when directly connected)
- Cable Modem
- Wireless-G Router (Model CWR-854) - Firewall enabled - All wired connections - No wireless enabled

Problems:
1) BitTorrent won't work properly. “Checking for firewall...” just keeps going
2) It won't allow access to internet banking sites completely. Accesses main pages, but times out when trying to log in.
3) Google Videos and YouTube slower.

Notes:
When I disable the firewall on the the Wireless-G Router, everything works fine. It's just the settings on my router firewall which is messing things up.

Attempted Solutions:

For 1) Allowed port 6881 for inbound and outbound TCP access on router firewall - didn't work - tried disabling Automatic port mapping (UPnP) - didn't work

For 2) Allowed port 443 (SSL) for outbound TCP - still didn't work

For 3) Haven't tried anything!
 

A:Configuration on Router Firewall - Painful :(

9 more replies
Answer Match 47.88%

HI GUYS,
I have a serious problem with cisco 2960 router,i am using a dell dimension 3000 running a microsoft windows xp proffessional.ANY HELP IS HIGHLY WELCOMED!
 

A:cisco 2960 router configuration

what problem are you having? Dunno if I can assist, but am curious as to your network setup.
 

3 more replies
Answer Match 47.88%

I can't seem to access the routers web configuration page, I get a Gateway Timeout message. I tried rebooting the router, then rebooted my system, but still nothing. It worked fine a few weeks ago. That was the last time I remember using it. I'm not sure what has happened. I checked the TCP/IP properties and everything is set to contain an IP address automatically. Plus in the ipconfig the default gateway is 192.168.0.1

I am running windows XP and my netgear router is PR114

I did look around the site to see if this question was posted before, but I didn't find anything off hand. If this question has been posted before, please post the link.. Thank you..
 

A:Can't access router web configuration page

14 more replies
Answer Match 47.88%

hi hope someone can help me.

How can i delete my nat entries where it says create protocol?

I am a beginner at this. I want to be able to make it more secure.

How can i do this?

Can i edit it using notepad and then import it using the browser?

Also my little network has 3 windows xp workstations and have been setup using windows xp networking ie. i created a disk and setup the other workstations on the network. Everything is working ok except for accessing files on the network. It takes about 2-3 minutes to connect to a share on another computer and access the files. Can someone tell my why?

Does the hostname in this firewall have to be the machine the modem/router is connected to?

here is a copy of my firewall

[ env.ini ]
set var="CONF_REGION" value="Australia" set var="CONF_PROVIDER" value="BigPond" set var="CONF_DESCRIPTION" value="BigPond defaults" set var="CONF_SERVICE" value="Router,PPPoA,DHCP,NAT,VPI/V* * CI 8/35" set var="CONF_DATE" value="Configuration modified manually" set var="HOST_SETUP" value="auto" set var="UPGRADE_URL" value="http://www.speedtouch.com/u* * pgrade500.htm" set var="COLUMNS" value="80" set var="ROWS" value="24" set var="SESSIONTIMEOUT" value="120" set var="HOST_MAC_ADDR" value="xxxxxxxxxxxx" set var="HOST_IP_A... Read more

More replies
Answer Match 47.88%

Ok quick question, i currently have 2 Dlink DSL 2640R's networked together and set up correctly, the Master router is assigning DCHP addresses and the secondary is forwarding to the relevant computer thats connected to it.

I have two PC's both connected to the secondary router, which are able to network together and use the master routers internet,

However, my girlfriend is buying a new laptop next week, and wants to be able to stream music from one of my PC's to her Laptop while connected to the Master router (so she isnt affected by any lags due to networking happening between my two pc's i regularly switch files between them, hence the second router)

so 2 questions:
Firstly, am i right in my above statement that if My 2 pc's are transferring via router number 2 router number 1 will serve her with no overlap between the 2?

and Secondly, DCHP is off on the 2nd router, and as far as i can see, the main router see's my pc's and the 2nd router is invisible, so am i right in thinking that her PC will be able to see both my PC's on the 2nd router? or will she just see router number 2? (i read somewhere that some routers see all clients connected to the 2nd router as one IP address and the 2nd router sorts it out when it gets there)
 

A:Solved: Multi Router Configuration

8 more replies
Answer Match 47.88%

Hi, I have the TP-Link wired TL-R600VPN router. I was able to access its configuration page from my PC and set the security so that only the PC's MAC address would be able to access it. Now my PC's monitor died and I tried accessing the router's configuration from my laptop, and obviously the access was denied as the MAC address is different. Is there a way to fix this? Thanks.

A:Unable to access router's configuration

If you have remote desktop setup on that computer you could remote into the the computer without a monitor other than that you may have to reset the router or if you have a computer running linux and you know the mac you could spoof it and logon

6 more replies
Answer Match 47.88%

Attached is a diagram of a network I’m trying to get configured. All devices are on the same subnet.

The Moden/Router “A” is WAN connected to the internet. Its LAN IP address is 10.0.0.1. Its DHCP server function is ON. Its DHCP range is 10.0.0.101 to 10.0.0.199.

Router B’s default address was 192.168.1.1 but I changed it to 10.0.0.2 and turned its DHCP OFF. It is assigned static IP address 10.0.0.2. It is wired LAN to LAN to Router A.

Router C’s default address was 192.168.1.1 but I changed it to 10.0.0.3 and turned its DHCP OFF. It is assigned static IP address 10.0.0.3. It is wired LAN to LAN to Router B.

Four devices connect wirelessly to Router A and do have internet access. One computer connects wirelessly to Router C. That computer has a local USB printer.

I have three network devices that I assigned static IP addresses to so they won’t be changed by Router A’s DHCP service. Two are connected to Router A and one to Router B.

Router C has three Linux computers wired to its LAN ports. One of those computers has two USB hubs wired to it and several USB devices are connected to each hub.

I want to be able to access the internet from any of the computers simultaneously and I need to be able to print to any of the four printers from any of the computers. I also want to be able to access the USB storage devices from any of the computers and access files on any computer from any other computer.

When I connect wirelessly to Router B I do have internet access. Rou... Read more

More replies
Answer Match 47.88%

Reuel,

Do you have any idea on setting up the Linkys Router with 4 port switch (besfr41)? I have followed the directions in the manual but I get nothing, no connection to the internet. The modem is connected to the router and the router is connected to the pc. Although I am using a straight cad 5 cable between modem & router. Use a crossover cable instead between the DSL modem and router? Any comments would be great.

Thanks
 

A:{Advice Given} - DSL/Router networking configuration

12 more replies
Answer Match 47.88%

My wireless linksys router is acting up on me again and i'm not sure how to handle this. I copied the error messages exactly as displayed. Sometimes the problem stops after i wait 30min or so but this is happening allot more frequently now.

I started getting these errors in this order

window failed to find domain name prpblems with DNS server
windows confirmed that ''primary DNS server'' is currently online, but is not responding to connection attempts at this time.

This usually means that a firewall is running somewhere between the two computers and is blocking ''domain''. windows has confirmed that windows firewall on this computer is correctly configured to allow this connection. However, a remote firewall might be blocking your connection.

The following policiy might need to be adjusted to allow windows to connect:

Policy provider: windows firewall firewall
filter name: query user

if the policy provider identified is windows firewall ,click for information about adjusting windows firewall settings. If a differnt policy provider has been identified, check the provider's documentation on how to adjust the policy settings.

Reset the network adaptor ''wireless network connection''
resetting the adaptors can sometimes resolve an intermittent problem.
 

A:Linksys router configuration issues

When Windows gives messages like that there are only two choices:

a. laugh; or

b. cry.

The problem goes away sometimes after 30 minutes with you doing nothing, right? Can you still access the router (ping it, or access its config or status pages)? Have you tried a reset or power cycle of the router? If so, does that clear the problem?

If it is a router problem about all you can do is make sure you have the latest firmware; then reset it to factory default settings and reconfigure it. Next step after that is to replace it.
 

1 more replies
Answer Match 47.46%

Hello,

Some of us don't use just a wireless router, but a combination of wireless and wired routers. In such cases the configuration of the devices can be a little tricky. But this thread it will be explained in depth, each step how to set up a wireless access points for laptops

This tutorial is going to explain how to set-up wireless for people who have setups similar to this model:

Modem -> Wired Router -> Wireless Router

Modem -> Wired Router -> Switch -> Wireless Router

***Note, there are pictures at the bottom of this post, use those for reference when going through this guide***

Supplies:

- Wireless router / power cord
- An ethernet cable to go from the router to the computer we'll be working with
- Oh, a computer with Internet Explorer or Firefox, no chrome yet lol

Step 1: Getting everything ready

- Take the wireless router, plug in the power, and take an ethernet cable from the back of the wireless router ***NOT THE INTERNET / WAN PORT but any port labled [1,2,3,4]*** plug the other end into the computer or laptop

- Now, once the laptop is booted up make sure its connected to the router
WIRED not WIRELESSLY

- Open up Internet Explorer or Firefox
- in the address bar type in the default router IP address which for dlink's is 192.168.0.1 for linksys products its usually 192.168.1.1 and hit enter
- if prompted for a username and password:
- dlink: username: admin password: blank
- linkys: username: admin password: admin

Step 2: Wirele... Read more

A:Wireless Router Configuration as a Access Point

I'm guessing its not too useful or it needs to be revised lol

5 more replies
Answer Match 47.46%

At work I am trying to figure out how to configure out wireless router. What I need to be able to do is to have people who use wifi to be able to also connect to our office file server (which will have shared printers so we can monitor usage amongst different departments). How can I do this? 90% of the office connects through wires using a static ip. Would I need to configure the router with a static ip as well? If so, would the wifi laptops need to have a static ip as well?
 

A:Wireless router configuration for use with file server

If there is a DHCP server on your office network, the following configuration for the router and allow the connections you seek. You could also use a wireless bridge if you haven't purchased yet.
Connecting two (or more) SOHO broadband routers together.

Configure the IP address of the secondary router(s) to be in the same subnet as the primary router, but out of the range of the DHCP server in the primary router. For instance DHCP server addresses 192.168.0.2 through 192.168.0.100, I'd assign the secondary router 192.168.0.254 as it's IP address, 192.168.0.253 for another router, etc.

Note: Do this first, as you will have to reboot the computer to connect to the router again for the remaining changes.

Disable the DHCP server in the secondary router.

Setup the wireless section just the way you would if it was the primary router, channels, encryption, etc.

Connect from the primary router's LAN port to one of the LAN ports on the secondary router. If there is no uplink port and neither of the routers have auto-sensing ports, use a cross-over cable. Leave the WAN port unconnected!

This procedure bypasses the routing function (NAT layer) and configures the router as a switch (or wireless access point for wireless routers).
 

1 more replies
Answer Match 47.46%

I had a couple of guests over and they were having problems getting online (actually they were on for a day but one laptop dropped) the problem was with the guest laptop itself. While troubleshooting we opened the router as an access point. It gave us a new address for configuration but did not get it all down. It is a Belkin Wireless G router and the previous config address was 192.168.2.1 the new one was 192.168. then 2 0r 1 follwoed by three number sequence I believe starting with 2 (I tried 245 and 254). When I right click on my wireless connection icon and go to properties none of the address work some now start with 70. Is the a way to find the address and if not how do I reset my router?
 

A:Solved: A Router Default Configuration Address?

6 more replies
Answer Match 47.46%

I am using Tenda wifi router. It has a problem, it is that it need configuration every time when I start my laptop or connecting with any mobile device. What is the problem with that?
 

A:Tenda wifi router need configuration every time

The Tenda wifi router's internal battery may be dead
 

1 more replies
Answer Match 47.46%

I apologize if I posted this in the wrong section.

I have been trying to achieve a Remote Desktop Connection with my office PC (Host -- Win XP Pro service pack 3) with my wireless laptop (Client -- Win XP Home) at my house.

The RDC works at my office in the LAN, when I have my laptop connected in the office network. However, from my home's LAN, I cannot access the Host over the Internet (WAN).

I have tried to open port 3389 for the RDC in the PortForwarding section on my Office's D-Link DIR-615 router setup and did the same for my home's belkin 54G router at home, under Virtual Server, in that setup.

Has anyone had this type of problem with Microsoft Remote Desktop?
 

A:Solved: Correct setup of DIR-615 router configuration for RDC

16 more replies
Answer Match 47.46%

Hi,

I have a D-Link Wireless N ADsl2+ 4-Port Wi-Fi router and my PC (running Windows OS) is connected to the router via. LAN cable
Other devices like Laptop, Tablet, etc. are connected to router via. WiFi

My ISP IP address, subnet mark and DNS Server IP address are configured in Router
And also a different DNS Server IP address is configured in Window OS as well in (TCP/IPv4)

I have few basic questions
a) What is the difference between configuring internet settings in Router and internet settings in PC ?
b) If I configure internet settings both in Router and OS, then which internet settings applies or takes precedence ?

Thanks

More replies
Answer Match 47.46%

I'm trying to run a server for a java application called mekwars. The program needs ports 2347 and 4867 open.

I have obtained an ip address from my ISP and registered with dyndns. I can ping my public ip address (my router)

I can access my server from any other computer in the LAN. My router is a Zyxel p660hn-T1a. I have configured port forwarding of both ports to my server.

I have disabled the firewall in the router and restarted it.

My server is running CentOS 6. I have opened the ports in the server iptables, I don't think this is the issue as I can connect from my lan to the server.

When I try to connect (from within my lan) to the public ip address of my server the program tells me it cannot find the server. I can't telnet to port 2347 and nmap tells me that the only ports that are open are 22, 23 and 80 ( I believe this are open by default on the router to allow remote management).

I can telnet from the lan. My networking isn't great and I'm used to having an "ip passthrough" option on the router to assign to my server. I do have it set as the default router in port-forwarding so I had hoped this would be a similiar option.

I've a funny feeling I'll have to telnet to the router to take care of some hidden options but I'm posting here first hoping some network guru will be able to say "Ah I ran into this problem back in 19dickity6... "

Can anyone give me any suggestions as to where I'm going wron... Read more

A:Help needed with router configuration for home server

When I try to connect (from within my lan) to the public ip address of my server the program tells me it cannot find the server.Click to expand...

You mean the public (WAN) IP address of the router, right? Some routers will "loop back" the way you want it to and others will not.
 

2 more replies
Answer Match 47.46%

hello guys,

good day! please i need your help on what to do's regarding wrh54g client configuration. i been setting up today the point of access for its secured network mode with WPA shared key on XP-SP3. tried successfully on a client with windows7 lappy, but then my problem was that my boss want me to set it on a manual mode. i mean, he wanted it that everytime he disconnect the wireless and decide to connect again later he likes to input again the password. but as ive see it everytime i tried to reconnect, the password is automatically inputted already and ready to connect. not unless u click the wpa box and the password will be deleted. boss wanted this kind of setup for security purposes. i hope u can help me on this matter. my other options also were not successful.

all comment and help will be highly appreciated.

regards,

twinx

A:[SOLVED] please help on WRH54G router client configuration..

Let me say this much. If that were the case with my wireless network, I would be entering my 64 character passkey every time I connected to my wireless network. I could just copy and paste it from a text file, but then what is the point of doing that over just letting the computer save it for me? If your boss wants to make sure his wireless security is strong, his efforts are much better spent doing what I have done by going to the website linked below, copying the "64 random hexadecimal characters (0-9 and A-F)", while using either WPA, or WPA2. The kind of authentication I think he is getting at, is something a radius server would be better at providing, provided your computers were part of a domain.

https://www.grc.com/passwords.htm

In Windows 7, I know it is possible to have it not remember your passkey provided that you do not check the checkbox during the connection setup. My memory is a little off with XP. Does it provide something similar?

5 more replies
Answer Match 46.62%

Our ISP provided a DSL modem/router (Netopia) that I connected to the Netgear wireless router with dd-wrt flashed. All I've done so far is connected the two. I have a connection, but I want to know if it's possible or advisable to configure everything from the Netgear router. But following the instructions herehttp://www.dd-wrt.com/wiki/index.php/Wireless_Access_Point, it seems I have to configure DNS and such using the Netopia router. I don't have a full grasp on how to use them together the correct way - like using the Netopia as an ethernet bridge. Thank you,

Brandon

Sent from my Motorola Electrify using Tapatalk 2
 

A:Netgear WNR2000 Router behind Netopia 2241N Configuration

6 more replies
Answer Match 46.62%

I have a Netgear MR814 router. I used to be able to access the configuration screen by entering 192.168.0.1 in the address bar and then inputting the default username (admin) and password (password).

That stopped working a while ago. I decided to reset the router to its default setting by pressing and holding the reset button on the unit. It didn't seem to work. I can still access the internet, but I can't get to the configuration screen. Sometimes it says that the server is busy without giving me the option to enter a username and password. Other times it does ask for the username and password. When I input them, it seems like it is going to work and the screen starts to load. Then it asks me enter the username and password again.

Can anyone help.

BTW the ISP is Comcast
 

A:Netgear MR814 Router can't access configuration screens

try resetting again, but hold the reset button in while unplugging, wait, and then re plugging the power supply to the router.
if that doesn't work, dropkick the router across the room. When I had this problem, my roommate did that (to my horror), and everything magically work, and has been working ever since.
 

1 more replies
Answer Match 46.62%

I have the following ethernet network configuration:

WAN

Router 1​
LAN
WAN

Router 2​
LAN
Computers
ISP Assigned Static IP
(W.X.Y.Z)
Static IP (A.B.C.1)
Static IP (A.B.C.2)
Static IP (P.Q.R.1)
DHCP Clients (P.Q.R.*)
ISP&#8217;s Gateway
No DHCP
Gateway = router 1 (A.B.C.1)
DHCP Server
Gateway = Router 2
ISP&#8217;s DNS

DNS = router 1 (A.B.C.1)

DNS = Router 2
One of my computers is set up as a web server and which I can access it from outside my network, but from inside my computer LAN, I cannot acccess it.

Can someone help me on how to configure the Router 2 DNS so that behind the router2, my website URL resolves to the local web server IP address?

Thanks in advance,
Moiz Tankiwala
 

A:Help needed for Router DNS configuration - Unable to access website from LAN

I ran into the same problem and had to use a proxy service so my
router didn't see it as a local connection attempt.
http://anon.inf.tu-dresden.de/index_en.html
 

3 more replies
Answer Match 46.62%

My computer is connected wirelessly to a Linksys router, which is connected to the internet through a modem/router that my ISP provided. When I enter 192.168.0.1, I am taken to the configuration page for my ISP's router. How do I access the Linksys router's configuration page?

I have tried all sorts of combinations of 192.168.x.x, but nothing has worked. Is there a way to figure out the address the Linksys router's configuration page? ...or is there a reason I am unable to access it?
 

A:Solved: Trouble accessing router's configuration page

9 more replies
Answer Match 46.62%

Hi everyone,

I recently tried setting up a Buffalo WHR-G54s router on my desktop (which has Windows XP on it) so that I can access the internet with my laptop as well. I have no problems accessing the internet on my desktop after connecting everything, but I can't access the configuration page to set a password and change the SSID.

The default IP address of the router config is supposedly 192.168.11.1. However, when I run ipconfig /all, the default gateway is listed as 67.186.14.1. This IP address also pings successfully. Nowhere is 192.168.11.1 seen after running ipconfig /all.

When I try accessing either of these IP addresses in IE or Firefox, nothing happens. I even temporarily disabled all PopUp Blockers and shields (as far as I can tell) to see if that would help as well. But nothing seems to work. Anyone have any ideas?

Thanks!!!!
 

A:Cannot access configuration page of Buffalo Router WHR-G54s

12 more replies
Answer Match 46.62%

I was a bit of a loss and maybe it's because I have been out of the game for a long time but I came across a disturbing development. I call century link because my router was not connecting at the proper speed of 7 mbps. That problem was easily remedied over the phone but the lady said she could see several devices connected. This lost me a bit because I have a double router configuration. The Actiontech PK5000 i turned into nothing more that an internet modem. I disabled the DHCP and configured my Linksys E1200 for all the internal DHCP so there is only one cable going to the PK5000. I should technically speaking look like one user on there network with natural protection from the second router. I may be kidding myself or man I'm getting old but if someone can tell me how that works it would be fun to know and what would even be funner to know is how to stop it!!!!!!!!

A:Interal network security with dual router configuration

Erm. Could you clarify what exactly you want? Your message is very... convoluted.

1 more replies
Answer Match 46.62%

Hi

I have a Dell 2350 wireless router which I have happily used in the UK for the last 12 months.

I have just relocated to Australia and am having real problems reconfiguring using the CD driver.

It acknowledges that there is an internet connection direct via the ethernet cable into the PC; following the steps the internet light is then on; then there are lots of flashing lights whilst it tries to configure; LAN port light flashes; but configuration fails; and there is no internet availability.

Please help if you can, I am at my wits end.

Thanks
 

A:Dell wireless router configuration / connectivity problem

I have had the same router for years, and in my personal and professional opinion, can it and buy a better one, it never worked well and was always laggy. but otherwise reset it to factory settings and begin setup from the ground up.
 

1 more replies
Answer Match 46.2%

my internet connection uses PPPoE to connect to the internet. i'm trying to set up the router for this configuration but it does not work. if there is anything else i need to post up pls tell me...help!!
 

A:Configuration problem for belkin adsl2+ modem with wireless router

the MODEM uses PPPoE, the router should not. the ADSL modem will hold the connection
regardless of anything being active on your router or systems, so imo, the router
should not be configured for PPPoE.
 

1 more replies
Answer Match 46.2%

Hi, I'm having a problem setting up my router. Whenever I connect my router to my modem, I get the error "Local Area Connection 2 doesn't have a valid IP Configuration."

How can I fix this?

This error goes away when I connect just my modem to my computer.

I know the router isn't broken, and I'm sure I have all the cables plugged in correctly.

Router Model: Netgear WNR2000

OS: Windows 7

Thanks for any help!

I've been trying to fix this for a week now!
 

A:Router Help! Local Area Connection Doesn't Have a Valid IP Configuration.

The following procedure should get you a connection with any broadband modem that is configured to use DHCP for the router connection, such as cable modems, and many DSL modems. If you require PPPoE configuration for the DSL modem, that will have to be configured to match the ISP requirements.

Note that the wireless encryption and channel selection will have to be done after the basic wired connection is established, the first step is to get wired connections working.

Reset the router to factory defaults by holding the reset button down for 15 seconds with power on.
Turn off everything, the modem, router, computer.
Connect the modem to the router's WAN/Internet port.
Connect the computer to one of the router's LAN/Network ports.
Turn on the modem, wait for a steady connect light.
Turn on the router, wait for two minutes.
Boot the computer.

When the computer is completely booted, let's see this.

Hold the Windows key and press R, then type CMD (COMMAND for W98/WME) to open a command prompt:

NOTE: For the items below in red surrounded with < >, see comments below for the actual information content, they are value substitutions from the previous command output!

In the command prompt window that opens, type type the following commands one at a time, followed by the Enter key:

IPCONFIG /ALL

PING <computer_IP_address>

PING <default_gateway_address>

PING <dns_servers>

PING 206.190.60.37

PING yahoo.com

Right click in the command ... Read more

1 more replies
Answer Match 46.2%

Hi Guys (and Gals?)

SUMMARY:
I want to add a second wireless router to my existing home network. Also I plan to upgrade to a "smart" (internet-connected) TV within the next year so I'm trying to plan ahead. I have a decent-sized house with many THICK walls (no drywall here!). Tech-oriented family of 4.

Other details:

1. Existing router is Linksys E3000 and has served well.

2. Four endusers in house: all technophiles and heavy data users, often simultaneously.
-- Son connects his self-built gaming monster machine via Ethernet. Hard core gamer thus streaming is critical. Also art student but I'd say his build has accommodated those needs well.
-- Hubby laptop PC and tablet and phone; streaming to tablet is critical, esp. from upper floor bedroom.
-- Daughter phone and laptop; streams to both, often from upper floor bedroom.
-- Yours truly mom, (and network admin)... heavy reliance on self-built desktop (Win 8.1), Asus laptop (Win 7), tablet, smartphone (often all simultaneously), streaming, bluetooth(s) (plural?) , whatever else I come up with.

3. 3 TV's that use the cable modem, but I plan (hope!) to swap one of these in next year to a smart TV (love the Roku I use now, which of course connects to my wonderful e3000 router) The TV to swap is on main floor, front of house.

4. Wiring: I live in an old house; translate: brick exterior (awesome), very thick plaster walls interior (they don't make em like this anymore, sooo cool), small-ish ro... Read more

A:Please advise on best router to add and configuration for house of heavy data users

Are you concerned about 'ac' vs. 'n' because of file copies (or streaming) on your LAN? Or is your internet access faster than you can handle with 'n' Wi-Fi?

If you use a SOHO router as wireless access point following is the complete procedure.

JohnWill's procedure (Aug. 30, 2008) for configuring a secondary router as a switch and, optionally, wireless access point follows.

Connecting two (or more) SOHO broadband routers together.

Note: The "primary" router can be an actual router, a software gateway like Microsoft Internet Connection Sharing, or a server connection that has the capability to supply more than one IP address using DHCP server capability. No changes are made to the primary "router" configuration.

Configure the IP address of the secondary router(s) to be in the same subnet as the primary router, but out of the range of the DHCP server in the primary router. For instance DHCP server addresses 192.168.0.2 through 192.168.0.100, I'd assign the secondary router 192.168.0.254 as it's IP address, 192.168.0.253 for another router, etc.

Note: Do this first, as you will have to reboot the computer to connect to the router again for the remaining changes.

Disable the DHCP server in the secondary router.

Setup the wireless section just the way you would if it was the primary router, channels, encryption, etc.

Connect from the primary router's LAN port to one of the LAN ports on the secondary rou... Read more

3 more replies
Answer Match 46.2%

Components involved in network
Dell Dimension 3000 Tower OS Win XP SP 2
Dynex Wireless G Router
HP Laserjet 4050 TN
What I'm trying to do.

Get the wireless router to recognize the Laserjet and assign it an IP address though DCHP.
The laser jet was originally configured on a physical Net Gear Route, thus it has RJ45 ehternet connection. When I connect the laser jet, Dell PC and the Dynex Wireless Router. The wireless network works fine as far as a laptop accessing the network, BUT the router does not recognize the laserjet and does not assign it an ip address. The laser jet had an static address with its old configuration. How do I get the router's DHCP to recognize the laserjet and assigne it an IP address? Any ideas or ways to configure the Laserjet to accept an IP assignment or lease?
 

A:Solved: HP Laser Jet 4050 configuration with Dynex wireless G Router

14 more replies
Answer Match 45.78%

Alright, heres the setup:

(1) DSL Modem
(1) WRT54G Router
(1) Desktop WinXP Pro SP2 machine, hardwired to router
(2) WinXP Pro SP2 laptops, wireless - one with built-in wireless, one with a Linksys WPC11 Instant Wireless Network Adapter, version 3.
(1) WinXP Media Center SP2 laptop, wireless
(1) Ubuntu Personal Edition - "Feisty Fawn" 7.04 laptop, wireless

The router has been set up to use WPA-TKIP encryption on channel 6 with an always-on PPPoE connection; it also has an IP of http://192.168.2.1 to avoid an IP conflict with the DSL Modem. DHCP Server is enabled with default settings, MAC Address Clone is disabled, and Operating Mode is set to Gateway. Access is set to allow both B and G, as one of the WinXP Pro laptops is an older model Toshiba that only recognizes the B protocol (that's the one with the WPC11 card).

Here's the problem:

Initially, the setup works flawlessly. All computers are able to see the SSID, connect to the network, and connect to the internet. The connection is fine, doesn't slow down, and is overall pretty healthy. All computers are able to access http://192.168.2.1, and are prompted with the username/password prompt, can change settings, port forwarding, etc.

Now, wait a few days. Usually about a week.

First, the Ubuntu laptop starts to get spotty with it's connection to the internet. After about 10 minutes, the connection to the network starts to fail. Sometimes it will see the SSID, sometimes it won't - and ... Read more

A:Linksys WRT45G > Unable to access router configuration, whole network degrades

I'd first upgrade to the latest firmware, and reset to factory defaults and reconfigure. If that fails, I'd have to suspect an issue with the router.

Many times heavy use of P2P does this to SOHO routers, something to consider.
 

3 more replies
Answer Match 45.78%

I have my main computer with the following setup

Windows Vista connected to the router then to the modem in Bridge Mode (so that I can use NAT1 with my PS3), thus internet works fine for both, my Main Comp (Desktop) using PPPoe and PS3 using a wireless connection between my router but also through PPPoe.

However, in terms of my secondary computer (Desktop), I have a USB Wireless Adapter, but I do not seem to be able to find the configuration for going on to the internet through the router but to use PPPoe.

The following are my products

Router - D-Link DIR-625
Adapter - D-Link USB Wireless Adapter DWL-G122
Modem - SpeedStream 5200

Thanks
 

A:Solved: Modem Bridge Mode + Router + USB Wireless Adapter Configuration

I'm a bit confused. If you're connecting PPPoE with two devices, that indicates you have two modems, which sure doesn't sound right. What are you really doing here?
 

3 more replies
Answer Match 43.68%

How do I make it so i can enable router forwarding?
Windows XP Home Edition-Westell Router Model E90-610014-06
 

More replies
Answer Match 42.84%

I'm trying to hook up a wireless connection in my home. When the DSL is connected regularly through the modem it works just fine. But when I hook up the Netgar router and try to set it up so that my son's laptop can have wireless, the internet will not connect. I get an error that gives me the option to redial but that never works either.

We tried a Belkin router (It just stopped working recently), then tried linksys, and now Netgar.

Thanks in advance.

Here's my hijackthis log:
Logfile of HijackThis v1.99.1
Scan saved at 6:24:33 PM, on 12/24/2008
Platform: Windows XP SP2 (WinNT 5.01.2600)
MSIE: Internet Explorer v7.00 (7.00.6000.16705)

Running processes:
C:\WINDOWS\System32\smss.exe
C:\WINDOWS\system32\winlogon.exe
C:\WINDOWS\system32\services.exe
C:\WINDOWS\system32\lsass.exe
C:\WINDOWS\system32\svchost.exe
C:\WINDOWS\System32\svchost.exe
C:\WINDOWS\system32\svchost.exe
C:\Program Files\Lavasoft\Ad-Aware\aawservice.exe
C:\WINDOWS\system32\spoolsv.exe
C:\WINDOWS\system32\dla\tfswctrl.exe
C:\WINDOWS\system32\rundll32.exe
C:\WINDOWS\system32\ctfmon.exe
C:\Program Files\Grisoft\AVG Anti-Spyware 7.5\guard.exe
C:\Program Files\Google\Common\Google Updater\GoogleUpdaterService.exe
C:\Program Files\Linksys\Linksys Updater\bin\LinksysUpdater.exe
C:\WINDOWS\system32\java.exe
C:\WINDOWS\system32\svchost.exe
C:\WINDOWS\system32\wscntfy.exe
C:\WINDOWS\System32\svchost.exe
C:\PROGRA~1\Yahoo!\browser\ycommon.exe
C:\Program Files\Internet Explorer\iexplore.exe
C:\WINDO... Read more

A:Wireless Problems: Internet works w/o router but not with router.

7 more replies
Answer Match 42.84%

Hey whats goin on to whoever reads this. I have a desktop HP pavilion with windows xp got it like in 2003 i believe never had a problem before but i have a laptop now so i hardly get on it, its the family computer really and it just carries the wireless router for internet thats all i worry about really. Anyways the computer was messing up and my mom told me that the screen kept turning red turns out i never really updated the virus software at all and "BLOODHOUND MORPHINE" found its way into the computer along with 30 other spywayre units, so i got new software at best buy not Norton dont worry i know better that Macafee and Norton. Anways the best thing to do really is restore the computer to factory settings...easy right ive done this thousands of times for friends or family to get them up and running in a hurry rather than searching and destroying a virus that hides itself very very well. So i figured no problem i ran the restore on the HP and it gets half way done and says "we need to restart your computer" that is normal so ok go ahead I carry on around the house and then i go back and this i have never seen ...the computer is booting and it stop on the loading windows XP page and a screen says " While trying to restore your computer a configuration problem occured, please contact your computers company and report the problem. Press 'ok' or hold down power key to restart computer "CODE PURPLE" So yea, ive never seen that scre... Read more

A:configuration problems please help never had this before!!!

Hey man! I know what it's like. I'm responsible for the maintenence of several pc's at work and home. Sometimes I'm stumped so I have to text for help here or call a couple people I know who are fairly amazing.

First of all, I'm presuming that your pc's still workable and not cooked in any way. So, at length, here goes:

• For starters, are you trying to run your pc through system restore or doing a fresh re- install? (I'm presuming that you probably have several things on your pc that you wish kept.)

• Do you have the OS disk? or was it installed and HP kept the disk?

• If you have the disk: Do you know anyone who would be willing to plug your HD into their pc temporarily as a slave drive? You may need them to run a virus scan & spyware scan then save your pertinent files onto a disk. Afterwards, they need to wipe out your HD completely: format it.

• Hook it back up into your pc, pop in your OS disk and go into your BIOS on boot: all my pc's use DEL when booting to get into it. Some use F2.

• Set your BIOS to Default: or Optimum or Performance, whatever. Any kind of default. Then before Exiting and saving the settings, set your Boot sequence: CD first, floppy 2nd and the HD next. Now save and exit. (Running the boot sequence CD first should bypass having to go into DOS hopefully. If not, I can't remember the typing sequence off hand. I have to actually do it to remember, but someone should be able to help you with i... Read more

1 more replies
Answer Match 42.42%

Hi, I use a COMPAQ Presario working off VISTA OS, and I seem to be getting configuration problems with peripherals. I don't know if it has anything to do with it but the problem started when I had my TALKTALK broadband upgraded to super broadband.
I discovered soon after that I could not communicate with my Kodak ESP 1.2 Printer across Wifi. I managed to redirect the printer to the new Wifi box, but can't cant communicate with it from the computer. I uninstalled the Kodak software and tried both downloading it and using the CD to reinstall the software, but the installation fails at the final stage.
I now find that some of the USB sockets do not respond when I plug something into them (so far a Galaxy 2 mobile and a SanDisk memory stick).
When I last corresponded with you July 2012, I had lost my DVD/CD drive and you provided a short piece of code to rectify a corrupt section of the registry, which had possibly been caused while installing some software, in this case probably iTunes. At the time the code solved the problem entirely.
I wonder whether I am having similar problems again in the registry area, and whether you can offer a solution.
Thank You
Roger Burch
 

More replies
Answer Match 42.42%

Hi all,
So, I recently installed a new OEM drive in my computer, the same as the previous one. It's an HP Pavilion dm4 3170se, and the drive is a hybrid Seagate Momentus XT (500 gb). This particular model has an SSD 16gb partition that's supposed to make startup a lot faster. When I upgraded to windows 8 on the old drive, and on Windows 8 on the new drive, this partition is not configured. A screen pops up before startup that says 'cache disabled' or something -- I can take a screenshot of that for more details.

How can I configure this SSD to do what it did before, that is, the intelligent hybird SSD startup?

Additionally, since I've replaced the drive, my fan has been running near-constantly, and once on startup I got an error that the fan was malfunctioning, though I haven't gotten that error since. I installed the hard drive exactly like the other one was -- is there something easy that may be causing this fan problem?

Thanks for your help -- software I'm pretty adept at, but hardware problems are generally beyond me. I appreciate it.

Andrew

More replies
Answer Match 42.42%

Hello anyone!!

I have had several bad experiences with linux before, but am still perseveering, and am sure that I am Beginning to see the end of this dark tunnel, my problems included 5 hard drive corruptions, randomly loosing my GUI, and just generally had problems, but as I said, I think this is the last set-up I will be doing for a while, I have got myself a far more reliable hard drive etc.

But my problem at the moment as the title may suggest is the configuration of Samba, I have tried all sorts of things, and then ended up resorting to pure trial and error, and can report 100% error, so I now have a messed up smb.conf file. Could someone please give me some advice on getting hold of a smb.conf file which has settings for just share level sharing, with an example share.

The thing that baffles me about the whole situation is that I managed to get hold of my smb.conf file from a previous installation (which worked), and now does not, I have a feeling I am blessed with bad luck!

If anyone could help, I will be eternally grateful (and in debt!)

Josh
 

A:Samba Configuration Problems

see this POST
 

1 more replies
Answer Match 42.42%

I have an Inspiron 1520 with Vista. A few days back I used Last Known Good Configuration after boot problems, and since then, the sites I use frequently (email, iGoogle, etc.) constantly log me out. All the passwords and logins are still stored, but as soon as I close the window or hibernate, I get logged out. It's getting really irritating. Anyone know what to do about this?
 

A:Problems after using Last Known Good Configuration

Make sure your web browser is set to allow cookies.
 

2 more replies
Answer Match 42.42%

I get a audio configuration error when I open itunes and I can't play the music when it opens. I uninstalled and reinstalled itunes and my audio driver. Any help would be appreciated. Thanks
 

More replies
Answer Match 42.42%

I've recently begun to have problems viewing some websites. For instance, from the MSN homepage when I click on any of the links under Sports by Fox Sports, I get "Page cannot be displayed". Also, I have a My MSN page that is customized with certain color scheme and news items. But when I go to that page, it does not display correctly. It's white and I can't see any images...just get the red x. Even in this forum, I can't see all of the images. It has to do with Zone Alarm Pro because when I disable that, I can view the sites and all images. I've checked and rechecked all of my settings in ZAP and they seem OK. I haven't tried uninstalling and reinstalling ZAP yet, if I need to do that will uninstalling through Add/Remove do the job? Any help is greatly appreciated.
 

A:Solved: ZAP Configuration Problems

14 more replies
Answer Match 42.42%

Hi there,

I'm having some problems with my computer and I was wondering if anyone could help me out.
Everytime I turn my computer on it won't connect to any wireless network. It says that the Wireless Zero Configuration is inactive. So I tried to activate it through services.msc and it gave me an error message ("Could not start the Wireless Zero Configuration service on Local Computer. Error 1068: The dependency service or group failed to start.")
After a lot of work looking for a solution to this problem, I found a way to fix it by going to the regedit, in HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Ndisuio and changing the Start value from 4 to 1. I thought I had solved all my problems, but everytime I turn off the computer and turn it back on I get the same problem, having to go to regedit and restart the computer for the internet to work.
Before this problem I always used Windows to connect to my wireless network and I don't have any other program for that purpose.
I tried to scan my PC for viruses and my antivirus (Symantec Corporate Edition) couldn't open properly, saying that it couldn't find a .exe file. I tried to install other antivirus programs like AVG and Avast and they both had problems during instalation, also saying that they couldn't find or create some .exe file. I used an online antivirus (Trend) and it did find some problems, and suposedly fixed them, but it changed nothing. I don't know what else to do! Please, help me! :)

Tha... Read more

More replies
Answer Match 42.42%

I have an Inspiron 1520 with Vista. A few days back I used Last Known Good Configuration after boot problems, and since then, the sites I use frequently (email, iGoogle, etc.) constantly log me out. All the passwords and logins are still stored, but as soon as I close the window or hibernate, I get logged out. It's getting really irritating. Anyone know what to do about this?

More replies
Answer Match 42%

Ok, I have Windstream DSL that connects through a Siemens 4200 modem that goes into my linksys wrt54g wireless router. So how exactly do I access the modem, if when I type in 192.168.1.1 goes to the router. How can I access the modem to port foward? The only current way I can get to access settings on my modem is to go to Windstream.net and go to configurations in the top right. From there I can access the modem. Is there any way to port foward with this modem?
 

A:[Siemens] Accessing Siemens 4200 configuration page with a Linksys router

11 more replies
Answer Match 42%

Our office currently has a Linksys 10/100 Router with assigned IP Address of 192.168.0.1 that our wired desktops connect through, as well as our printers, data storage server and cable modem. All of the connections have IP Address based upon the 192.168.0.xxx. All of the computers on this router, except for one of the printers and the data storage server, are DHCP assigned IP addresses.

We have a D-Link Wireless router attached through the Linksys Router with an assigned IP Address of 192.168.10.1 that we use for wireless access/hard wire access in the office for anyone that comes in and needs to have access to the internet or our data storage and printers.

I can connect a laptop wirelessly or wired to this router. The computers can browse the internet and see any computers on the network, but cannot connect to any. Specifically the data storage server. I am not too concerned with the laptops connecting to the desktops connected to the Linksys router, but I need them to connect to the data server especially and have the ability to print to at least one of our printers.

Any suggestions? I know that it's probably something really simple that I am missing or doing wrong, but I just can't put my finger on it.

Any help would be greatly appreciated.

Thanks!
 

A:Wireless Router and LAN Router Setup Problems

10 more replies
Answer Match 42%

alright here's my problem...

I have my house networked via two linksys BEFW11S4 routers. The first is connected directly to my modem and four connections go to other rooms in my home. No biggie, no problems...

...until I needed 2 more ports in my office. SO i got my other router out, same model, and plugged the wall connection into the back, and then proceeded to plug in my computers into the three ports in the back. I can get no connection at all unless I plug my computer back into the wall then everything works like it should, so i'm guessing I have to do something in the router to set it up as a switch only, but I'm not sure how to do that. I've disabled DHCP, and some other things but I'm still in the dark.

Here's my setup-

Cable Modem > First Router >

First Router > Ports 1-3 to other rooms , Port 4 to my office...

Port 4 (from the port in my office wall) > Second Router >

Second Router > 3 computers that all need a connection to the internet

Any help at all would be wonderful as i have no friggin clue what to do here, linksys support is vague on the subject, and the customer service is clueless.
 

A:MODEM > ROUTER > ROUTER Problems?? Any suggestions?

seraphin said:



alright here's my problem...

I have my house networked via two linksys BEFW11S4 routers. The first is connected directly to my modem and four connections go to other rooms in my home. No biggie, no problems...

...until I needed 2 more ports in my office. SO i got my other router out, same model, and plugged the wall connection into the back, and then proceeded to plug in my computers into the three ports in the back. I can get no connection at all unless I plug my computer back into the wall then everything works like it should, so i'm guessing I have to do something in the router to set it up as a switch only, but I'm not sure how to do that. I've disabled DHCP, and some other things but I'm still in the dark.

Here's my setup-

Cable Modem > First Router >

First Router > Ports 1-3 to other rooms , Port 4 to my office...

Port 4 (from the port in my office wall) > Second Router >

Second Router > 3 computers that all need a connection to the internet

Any help at all would be wonderful as i have no friggin clue what to do here, linksys support is vague on the subject, and the customer service is clueless.Click to expand...

The 3 computers on the second router needed their DNS specified to be 192.168.1.1, and the second router setting itself set for DHCP instead of typical PPOE.

The above is the simplest, least complicated config.
 

2 more replies
Answer Match 42%

These seem like they may be related, but when i go to "Run" and type in "ipconfig" it closes instantly. Also, when I type in my IP in my browser to go to the router config it loads fine, but clicking anything results in a 404 error, could anyone tell me what's going on?

*EDIT*

Forgot to mention, I'm using Windows XP. If any other info would be useful let me know.
 

A:Solved: Problem with router configuration and "ipconfig"

6 more replies
Answer Match 42%

Alright. I have been having problems with the internet for the past day.

Two nights ago, I couldn't connect to the internet, and like the fool I am, I thought something was wrong on the computer so I began clicking randoms settings on it. (As it turns out the modem just wasn't turned on.)

I ended up ACCIDENTALLY deleting the wireless network icon (or something to that effect) and the black netgear icon disappeared.

The icons are back (now is says 'wireless connection 2' and the internet works for a while then errors start popping up and when I click on 'network connections' it says:

"Windows cannot configure this wireless connection"

I called NETGEAR. No help. I called SBC. No help.

There is nothing wrong with the modem or router, they told me and the signal coming from the router is 'Excellent'.

Please, please help.
 

A:GOING INSANE: problems with Wireless configuration..

9 more replies
Answer Match 42%

I looked on the ZA site, but couldn't find an answer for this problem: ZA is blocking a lot of images on the internet, some animated, some not. And these are animated gifs, not Flash, etc.

Some of the images ZA blocks are signature graphics and avatars.

Do you guys know how to configure ZA to not block this? Also, I'm having trouble logging in to my forums with ZA running.
 

A:Zone Alarm configuration problems

12 more replies
Answer Match 42%

Okay, here is the scenario...

Drive #1 is split into two equal partitions

Partition C: has Vista Home Premium on it

Partition D: has XP home on it

Drive #2 (Drive E:) is for my data/games/etc, and has no OS on it.

I had the system set up where I could choose either OS upon boot.

Yesterday, for whatever reason I was greeted with...NTLDR is missing and I couldn't get into either OS.

Booting from the Vista DVD I repaired Vista, which is the only OS that appeared on the list and the system now boots straight into Vista, with no sign of XP.

I accomplished this by following the directions on THIS website under Step 3, but when I try and proceed as the administrator with step 4 I get...

"An error occurred. The system cannot find the file specified."

Out of curiosity, at command prompt I typed in "bcdedit" and under Windows Boot Manager, next to Device it says Partition=E:

Does this make sense? Drive E: has no OS on it. Why would the boot configuration be on it?

Any advice as to how I can get things back on track?

A:Dual Boot Configuration problems

Thought perhaps this would help....

5 more replies
Answer Match 42%

Ive been having a problem lately with my Firewire card. I own a 30GB IPod but i can't transfer music to it because there seems to be a problem with the configuration of the firewire card. Whenever i attempt to transfer music properly, my entire computer freezes halfway and no files make it to the IPod. This same problem occurs when using a firewire external hard drive. I tried using a different card but the problem persists. A friend of mine told me it must be something with the configuration but I am not too confident as far as messing with that myself. Could anyone please help me out here?
 

A:Firewire Card Configuration Problems

There seem to be hundreds of problems with firewire cards and IPod. Installation of "Ephpod, or XPlay with MacOpener on your Windows PC" appears to be needed also. Check here:

http://www.ipodlounge.com/

Check FAQ's and the forums.
 

1 more replies
Answer Match 42%

Just got a new Maxtor 320G PATA drive to replace my existing 40G. I installed it as the slave (cable select) and used the maxtor "Maxblast" utility to mirror my C: drive to my D: drive. All seemed fine and the utility formatted my D drive and mirrored my C drive. Because my C: drive was fat32, it formatted my new drive as fat32 as well.

I then removed the old C: drive, reconfigured the new drive as C: (swaped cable to C: position) and hooked up my old D: drive so I could copy it's contents as well. Everything went well, system booted on the new 320G drive, and I dragged the contents of D: over to the new drive.

I thought all was well except for the FAT32 format. I used the Microsoft "convert" utility to change from FAT32 to NTFS, said yes, yes, and rebooted. When I returned, the drive said it was still FAT32! I tried to convert it two more times with no luck!

I decided to put my old C: drive in as the primary and my new drive as the slave (swapped cables). When I rebooted, it showed my new drive as raw format and only having 128M capacity! I tried disconnecting the old C drive and hooking the new drive back as C and it would not boot, giving a windows error as soon as it tried. Could do nothing!

Then I tried to go back to the beginning and format my new drive again, but it is formatting it as a 128G drive only!

Help!! What did I do wrong?
 

A:Hard drive configuration problems! Help

16 more replies
Answer Match 42%

I recently purchased Norton Internet Security 2008 and can't get it installed properly. When I pull up the Norton screen, it says advanced firewall is at risk and other items secure. It also says Norton Internet Security configuration is not complete. When I click on configure or fix now, it won't ever connect to the account. I then do contol, alt, delete and it says the program is not responding.

I have talked to Norton live chat many many times. First I found the disk that I had purchased had problems so I was instructed to download it from their website. I have used their tool to remove both 2007 and the 2008 versions before reloading the 2008 from their website. I have tried removing the firewall and other spyware programs. I've removed my wireless router. Norton has run remote scans on my computer more than once. No viruses found. Now I am problems with IE7 freezing up which looks like it could be related ? Any ideas what could be wrong? I didn't have any problems with 2007 version. I have Windows XP.
 

More replies
Answer Match 42%

Hi
I have been using a Belkin Wireless Router on my XP Pro system for some time but now it will not connect to the web.

I think the problem has been caused by a virus but my system appears clean now.

As it stands I cannot access the Router Configuration because the message "Network Not Available" appears.

I have been in contact with my ISP, Belkin and have replaced the router with a new one all without success.

I have looked into the WZCSVC and other services and when checking the dependencis the nessage "WMI:Critical Error" appears.

All settings on the system are correct for setting up the router but it will not access the web. it seems the computer will not allow the router to "talk" to the web. Whatever caused the problem also appears to have deleted the system restore poits.

Does anybody have any suggestions for sorting this out.
Thanks in advance
Motters
 

A:Wireless Rouyer Configuration Problems

15 more replies
Answer Match 42%

SATA150 MAxtor 80g
ASUS P4X800D-X mobo
Corsair 512 3200 ram
P4 2.4c 800 fsb

Hi, I am trying to fix my moms computer, which has recently gotten a new motherboard. With the drive connected, it will not recognize it as an IDE master or slave, and it will not show in the main BIOS screen. However, it DOES show in bood device priority, and I can boot from the HD. I have messed with every setting remotely close to pertaining to the harddrive.

Now, When tryin to install windows on the HD, It will not find it, so that is impossible. The motherboard was sent back and replaced as well as the HD but it still will not see it.

I can install XP on it in my computer, which I did, and then put it back into my moms comp, and it is able to boot of the HD, still cant see it in BIOS. It will load the windows XP splash loading screen for a second, show an XP blue screen of death, you know the one im talking about. With the neat string of 0x0000002, 0x300000 whatever. BUT it just flashes for a split second and then it restarts. So I cannot see the string to pinpoint my problem.

I am stuck. Please help me this has gone on for far to long
 

A:Problems with motherboard and harddrive configuration HELP!

Gonna have to Bump
 

7 more replies
Answer Match 42%

I have done my best to configure Windows 2000 Server for active Directory; however, I am out of my element here so I'm not sure. I then went to the client and installed the snap-in for Active directory. The client is rinning Windows 2000 Professional.

Now when I click on Active Directory Sites and Services, I get the following error:
Naming information cannot be located because:
The specified domain either does not exist or could not be contacted. Contact your system administrator to verify your domain is properly configured and is currently on-lineClick to expand...

Can someone list some things I might check or places to look for an answer to this?
 

More replies
Answer Match 42%

I cannot restore my machine and wonder if it is because I am using raid 0 stripping? This is a laptop with dual 80 gig drives. Any thoughts on this , or do I perhaps have another issue to look at?

More replies
Answer Match 42%

What do you think about this HW configuration. I do not use my computer for playing games, thus no external GPA. Do you see any compatibility problems? Would you recommend changing some component?

INTEL CORE 2 E6750 2.66GHZ 1333/4M S775
ASUS S775 IG33 VGA DDR2 SATA-2 GLAN 8-CH
2GB 800MHZ DDR2 NON-ECC CL5 DIMM (KIT OF
LG DVDRW 20X DL BLACK LS SECURDISC NERO
WD CAVIAR SE16 320GB SATA2 7200RPM 16MB
COMPUCASE MIDI BLACK ATX W/O PSU
COMPUCASE ATX 350W PSU,RETAIL,2XSATA P4

Thanks for any help!
 

More replies