Tech Problem Aggregator

Satellite X - Where to get firmware update?

Q: Satellite X - Where to get firmware update?

I have a Toshiba Notebook with following internal DVD-RW drive: "TS L632D T004 Toshiba".

The problem is, this drive doesen't burn DVD+r DL without failures.
I made quite much attempts with 10 DL DVDs und five different burning suites, without success.
So I guess to fix this failure with a firmware update.

Can somebody tell me where I can get this update?

thanks :)

Best Regards,

A: Satellite X - Where to get firmware update?

Hi buddy,

Why should this issue related to the firmware?

In my opinion you should try removing the upper and lower filters in registry. Just follow this article:
http://support.microsoft.com/kb/314060

And firmware updates you can get from the Toshiba website.

1 more replies
Answer Match 73.5%

Hello,

My laptop is a Satellite PRO P100-383 with a DVD writer MAT****A UJ-850S.

The actual firmware of my DVD writer MAT****A UJ-850S is 1.10 and i can't write some DVD-R because they are not recognized as a DVD-R but as a CD-R. I think it's just the DVD-writer's firmware which is too much old.
Is there a way to update that firmware with a new one please ? because i've found anything in the download section for my laptop. Just drivers and motherboard BIOS, but nothing about the MAT****A UJ-850S firmware update.

Thank you very much for your reply.

Friendly.

Philip.

A:Satellite PRO P100-383 DVD UJ-850S Firmware update

Hi Philip

In my opinion you should not change anything but use high quality DVD-R medias like TDK or Verbatim.
Maybe you use ?some? cheap and no-name empty medias.

Have you tested it using well known brands?

2 more replies
Answer Match 73.5%

Hello! I have looking for newer firmware in this forum and i have not find anything...I have x200 25d model with this model of burner but i can?t truncate any dvd dl with imgburn software. the same model in acer laptop witn 1.61 firmware can truncate the dvd dl.

Is there any firmware update for my model? Thanks a lot!!

A:Satellite X200-25D: looking for Mat****a uj850s firmware 1.90 update

Hi

Found some firmware updates for this notebook model on the Toshiba European driver page but the firmware updates are released for TS-L632 or TS-L632P ODD drives.

Mat****a uj850s firmware update does not seem to be available.

1 more replies
Answer Match 56.28%

I can't find my previous post that I've made. Long story short, I installed with a plugged in laptop a new firmware, 1.30, and around 90% imy laptop crashed with the same sound it does when you hold the power button. Now it's working fine but i can't see it having isntalled properly. Is there any way to reinstall it or is the laptop doomed?

More replies
Answer Match 56.28%

Hello,

My Satellite X200 was running Vista and I installed Win7 myself. I also installed Tempro.

Now Tempro offers me 4 firmware updates dating back from 2008. The readme text warns me to check the FW version first using Toshiba disk creator.

But I don't have this program installed any more and I don't know where to find the FW version without it.

Should I install Toshiba disk creator first (but I didn't find a Win7 version for my x200) ?

Or can I go ahead and install the updates without checking the FW version ?

Thank you very much for your advice
Nicole Rosset

A:Satellite X200 - Which firmware updates should I install ?

Hi NicoleRosset,

From my own experience I can say forget the firmware updates of CD/DVD drive. I never did such an update because it?s not necessary if the drive runs properly. So if you don?t have any problems with your CD/DVD drive, just ignore the TEMPRO message.

I hope I could help :)

5 more replies
Answer Match 56.28%

Hi,
I had tried to replace the old DVD/CDRW with the above UJ-830B ( FW: 1.50, HW: 1.00) but the result was IDE error. It is not recognize it in Windows at all.
I have tried to solder the contact 48 and 49 but result is the same.

How can I make to work this UJ-830B ( FW: 1.50, HW: 1.00) on Toshiba Pro M10?

Is any one have any solution like firmware upgrade or some hardware soldering/desoldering?

Thanks.

Regards

A:Satellite Pro M10: firmware upgrade issue DVD UJ-830B FW:1.50, HW:1.00

This is not possible because such software is not placed or released on any of Toshiba webpage.

Fact is that not all CD/DVD drives are compatible with all notebooks due to different master/slave/c-sel settings.
Therefore it?s always advisable to contact the ASP in your country or to check the user manual to get the details about combatable drives.

I can recommend only buying an compatible and supported ODD.

Bye

1 more replies
Answer Match 53.76%

Toshiba Satellite a25-s207. Windows XP Professional.

how do I lower the brightness without the use of function keys?
I do not have the startup disks or anything that my computer originally came with six years ago. I have recently reformatted my computer. I've searched on the internet for drivers only finding rather fishy websites. I have looked extensively through the toshiba website ( such as through this link http://www.csd.toshiba.com/cgi-bin/tais/support/jsp/modelContent.jsp?ct=DL&os=&category=&moid=429794&rpn=PSA20U&modelFilter=&selCategory=3&selFamily=1073768663&selModel=429794%7CPSA20U)
only finding some driver support. I realize this product doesn't get updates any more, but I'm trying to figure out what bios and firmware options this thing needs or even if I'm saying that right. I can't even access the function keys to lower the brightness.
If there is something more I should post please let me know. Thank you very much.

OS Name Microsoft Windows XP Professional
Version 5.1.2600 Service Pack 2 Build 2600
 

A:Toshiba Satellite A25-s207, recently reformatted, needing firmware support...Possibly

The big mistake that you made before you formatted the hard drive and did a fresh install of Windows XP Pro in your Toshiba Satellite A25-S207 laptop was not writing down the descriptions in the Device Manager for:

Display Adapters

Network Adapters

Sound Video And Game Controllers

and then obtaining and burning off to a CD-R the current drivers for them.

----------------------------------------------------------------

I checked the Toshiba link that you provided. You'll have much better luck refining your search with Windows XP instead of Windows XP SP2/SP3, and then selecting Display and Sound and LAN and Mouse and downloading the drivers from there.

----------------------------------------------------------------

Don't worry about BIOS or firmware updates. They're usually not needed, and you can render your laptop or the drives inoperable by installing the wrong ones or if the install goes wrong.

----------------------------------------------------------------
 

3 more replies
Answer Match 53.76%

Can a Firmware Update and/or drivers on printers be reversed?I am new to BleepingComputer, so I do not know which Forum to post this to, as this issue involves multiple forums: Hardware (HP Printers), Software (Firmware & Drivers), Operating Systems running Windows 2000 and Windows XP.At my workplace, we have many HP Printers on the network. HP sent me a link promoting HP Easy Printer Care. I figured I would try it (big mistake) because I take care of all of the printers in our building. So this Easy Printer Care tells me that there is updated Firmware for my printers. So I get the firmware and install it. Of course, HP didn?t really explain how to install it. I had to look it up to actually do the install. After installing it, HP tells me that the Firmware Updates still need to be updated!?!Now the end users are having problems when they print. Multiple users are having the same and or different problems. The problem that has the most reports to me are: When someone is printing a document and they want to change it from portrait to landscape, they click on properties and receive an error message that reads:Function address 0x2e2a5aa caused a protection fault. (exception code 0xc0000005) Some or all property page(s) may not be displayed. Click OK.Then another windows pops up saying: Operation could not be completed. Click OK.The function address is always different (for different users or systems) The exception code is always the same. The User c... Read more

A:Can A Printer Firmware Update And/or Driver Update Be Reversed?

You can go to Device Manager and find the printer and in properties it gives you the option to "roll back" the driver to a previous version. A firmware update and driver update mean 2 different things, to me anyways. My understanding is a firmware update offers "improved" instructions to the onboard chip of the device. What does HP say about the problem?
Mark
'

3 more replies
Answer Match 51.24%

ok ive checked a bunch of sites and i wanna get my routers firmware to 3.43 so that it'll be primed for halo 3 tommorow. the problem is when i try to download i end up with a 505 error message saying: failed to change directory

Can anyone help?
 

A:DI-614+ firmware update

7 more replies
Answer Match 51.24%

Trying to update firmware on blu-ray but frm file will not write in Vista says I need supported writing software. What exactly do I need to do this?

More replies
Answer Match 51.24%

O.K. when originally wanting to do an Upgrade to Windows 8 i used VM to check it out.When i decided after alot of research to do the upgrade i used Windows 8 upgrade assistant.The message i receved on compatibilty was only one problem.Your PC Firmware doesn't support secure boot so you won't be able to use it in Windows 8.Secure boot requires firmware that supports UEFI v2.3.1 Errata B and has the Microsoft Windows Certification Authority in the UEFI signature database.Sure anyone who has UEFI like me received this message using this upgrade assistant.Through many hour and days of research on internet and other forums nobody seems to know how i can update my firmware,neither ASUS could advise me or Microsoft.To me i figured it should be a BIOS update,but no new ones are available for my system.So since i had no answers i decided just to do an install of Windows 8 Pro 64 bit (clean install) works well,faster then Windows 7.So far i like it.Only clue i have at this point was a site i found.Knowing my BIOS is a American Megatrend http://www.ami.com/Products/BIOSandEFIFirmware/AptioV/  Not sure if this is an answer to be able to do a UEFI install of Windows 8 Pro again to get full use of secure boot,GPT Partitions,but this is closest clue i got.BIOS stuff and flashing it can always be risky,rendering the motherboard inoperable,causing major issues,that i do not want to do.If anyone knows anything on this and can help with it would be very much appreciated i am stumped on thi... Read more

More replies
Answer Match 51.24%

Laptop is a Dell Vostro 1000 with XP Home SP3. Just installed a Crucial SSD. Works great. Tried to install a firmware update; not so great. Following the instructions from the Crucial site, I downloaded the update (it's an ISO file) and burned it to a CD. In the BIOS, changed boot order to CD drive first. Restarted the laptop. No joy - Windows still boots to the desktop. What could be wrong? I know almost nothing about using ISO files. TIA.
 

A:SSD Firmware Update

CD-image ISO files have to be written to CD in a special way, if you just copied the ISO file to a CD like a normal file, that won't work. There's a free app for creating a CD from an ISO file, it's called IMGBurn: http://www.filehippo.com/download_imgburn/
 

2 more replies
Answer Match 51.24%

Im not sure how to update my firmware. Im having trouble burning CD-Rs with nero 7.0 because it keeps coming up with this calibration error. I posted that thread in this same forum ( http://forums.techguy.org/multimedia/453562-nero-issues-data-disks.html)
but it just leads to this new question about updating my firmware because it might be a possibility. Im also running SP1.

I went to this page called "the firmware page" link- (http://forum.rpc1.org/dl_all.php) and searched for my Disk Drive but had no luck in finding it. Even if I were to find it, how would I go about updating it, and how can I tell if its up to date?

Im running win XP and it is a Toshiba Qosimo laptop e15-av101
I looked in my computer/cd drive/ properties to see the name of my drive and hopfully I have the right one, it is a

MATSHITA dvd-ram UJ-830s.
 

A:How do I update my firmware?

16 more replies
Answer Match 51.24%

Could someone please tell me the manufacturing web site for MATSHITA CD-ROM CR-586 and OPTORITE CD-RW CW4802 so that I could do a firmware update??????????????????????????????????????????
 

A:Firmware Update

16 more replies
Answer Match 51.24%

I have installed Open Wrt Bin file on my WR703N Mini portable wifi device. After that it doesn't broadcast WiFi Signals. But Through the LAN cable and using ftp i can connect the Flash memory. Please anyone can help me to Update to my Old Firmware version using FTP. I have my old firmware version's bin file. Pls help to me.
 

More replies
Answer Match 51.24%

Hello, I have recently purchased an "Onyx Portable Media Player" by "Mach Speed Technologies". I installed the included drivers and software and am currently upgrading the firmware. The update window says "SigmaTel MSCN Firmware", so I'm assuming it's licensed by SigmaTel. It's updating from version 000.000.000 to 880.282.433. The window's progress bar seems to be stuck at "Initializing", with no advances made in the main progress bar but the smaller one constantly filling and then refilling. Is this just going to take a long time or is there something wrong?

I can provide a screenshot if needed.
 

A:Firmware update

Is this the media player firmware or motherboard?
Why did you feel the need to upgrade the firmware?
 

3 more replies
Answer Match 51.24%

I have an Olympus Evolt-500 that won't update the firmware. I'm running XP pro with a DSL internet connection. I've talked to every tech support person Olympus has and they don't have a clue what's wrong.

It will recognize the camera and lenses but it will download from 50% to 83% of the firmware update, then a message pops up and says no connection to server and everything shuts off. They had me try the download with no firewall on and using just the modem no router. I've used Olympus Viewer, Olympus Master and Olympus Studio Trial version and they all download about the same amount before they shut down.

I'm open to suggestions at this point.
 

A:Can't update firmware

14 more replies
Answer Match 51.24%

I periodically check the website for my router to see if there are any new firmware updates. I checked it today and every time i try it says :
A New Version is Found. Do You Want to Upgrade to the New Version Now?

Firmware Version:
Current VersionV1.2.0.8 New VersionV1.2.3.7

I click Yes.
It then tells me that the update failed.
Any suggestions?

I am running an XP machine.
I have Verizon DSL.
I have a Westell model 2200 modem and a netgear wnr2000 router.

Any other information you need i will try my best to provide. Just ask.
Thanks
 

A:Can't Update Firmware

9 more replies
Answer Match 51.24%

For those with any of the following, OCZ has issued a series of firmware updates for the OCZ Vertex 3, Vertex 3 Max IOPS, Agility 3, Solid 3 and RevoDrive 3 bringing the firmware towards version 2.22,

OCZ Technology

For those with Windows installed on it the USB stick method works very well (and easy to set up),

NEW! - Bootable tools for OCZ SSD's

List of resolved issues (as well as a direct download link) can be found here),

OCZ Vertex 3, Vertex 3 Max IOPS, Agility 3, Solid 3, RevoDrive 3 2.22

A:OCZ SSD Firmware update for...

Thanks! My Agility 3 will appreciate this.

1 more replies
Answer Match 51.24%

Hey guys I have a Samsung SH-S222L. Should I upgrade the firmware to SB02?
 

A:Should I update the firmware?

Are you having a problem the firmware upgrade corrects? If not, leave it alone.
 

2 more replies
Answer Match 51.24%

Hi,

I have a Gigabyte CD-RW. model GO-R5232B. I downloaded a zipped Firmware of the same model from the Gigabyte website. Is it safe to update my hardware with this firmware even it has not encountered any problems for the past two years?

Tony
 

A:When to update Firmware?

9 more replies
Answer Match 51.24%

Dear Users,
Netgear WGR614 v7
Please advise on why I can't update the firmware. Every time I get the message that the upgrade has failed.

Arturo
 

A:Firmware update

13 more replies
Answer Match 51.24%

I have Aspire E 14. Last night, I saw I have 1 critical update for firmware v1.17. When I clicked the update button it just says "updating" It just goes on and is not stopping. I closed the portal and a window appears saying reflashing. I saw it did reflash up to 100%, but why won't the critical update notification disappear on Acer Care Center portal? I also checked update history and the firmware is not yet included. I tried it again the next morning, clicked the update button, but still, it just says updating and can go on until you close the portal.  Any solution? Did my Aspire really did reflash? It seemed nothing has changed. Thanks in advance!

More replies
Answer Match 51.24%

Okay I want to update my DVD-rom Driver due to it having a difficulty playing LOTR-FOTR Special Edition.
Here's a link to LG's site http://ca.lgservice.com/index_b2c.jsp Link doesn't work.Got to www.lgservice.com than to Canada,than to device driver,dvd-rom,scroll down to LOTR-FOTR Special edition.Will tell you there.
Now I know that I have to download the files from www.bootdisk.com for Dos. 6.0.After I do this do I double click on the files,from Bootdisk.com and send them to a floppy disk?Than after that the 2 files from LG's site I put on this Bootable Disk?
Restart the computer type in the command and let it go?
If I do this wrong is there anyway of screwing up my Bios,I have a Dell computer and don't want to screw anything.
The Lg Dvd-rom I bought seperatly and installed myself.
Someone help me on this or was the above correct??
 

A:Firmware update....

6 more replies
Answer Match 51.24%

I don't know much about firmware updates as I never had to do it but my DRW-2014L1Tburners are giving me some coasters in vista x64. Not 1 coaster under Nero 6 in xp pro.

I got the driver update listing in the sticky, went to the asus site to check on a firmware update for my burner's for x64 vista and there are 3 hopefully that will eliminate the coasters.

My question is: If I get the updates for the 64-bit vista will that interfere with those drives when I use xp pro ?

thanks,
kevin

PS: I use swappable drives; switching between vista x64 and xp pro.
only keeping xp for gaming and Nero 6

A:cd/dvd firmware update ?

Originally Posted by kem


I don't know much about firmware updates as I never had to do it but my DRW-2014L1Tburners are giving me some coasters in vista x64. Not 1 coaster under Nero 6 in xp pro.

I got the driver update listing in the sticky, went to the asus site to check on a firmware update for my burner's for x64 vista and there are 3 hopefully that will eliminate the coasters.

My question is: If I get the updates for the 64-bit vista will that interfere with those drives when I use xp pro ?

thanks,
kevin

PS: I use swappable drives; switching between vista x64 and xp pro.
only keeping xp for gaming and Nero 6



no the firmware should be backwards compatible

5 more replies
Answer Match 51.24%

I have Aspire E 14. Last night, I saw I have 1 critical update for firmware v1.17. When I clicked the update button it just says "updating" It just goes on and is not stopping. I closed the portal and a window appears saying reflashing. I saw it did reflash up to 100%, but why won't the critical update notification disappear on Acer Care Center portal? I also checked update history and the firmware is not yet included. I tried it again the next morning, clicked the update button, but still, it just says updating and can go on until you close the portal.  Any solution? Did my Aspire really did reflash? It seemed nothing has changed. Thanks in advance!

More replies
Answer Match 51.24%

hi everyone. I would like to know if i should update the firmware on my ssd. It is not brand new, maybe 3 yrs old. ocz technology. I have neve done this. So i need to know how to figure out exactyly what i have and if i even need to.

any help would be much appreciated

A:update firmware

I don't see any harm in updating firmware. But please identify the firmware that you would like to update and what exactly are your doubts about doing it.

9 more replies
Answer Match 50.82%

HP-Update FIRMWARE update problem?
I got some critical update for my Seagate 320 gb hard drive?s firmware. I went to download an process the update, later it asked me to insert a blank disk. Well I don?t have a blank disk but I hit bootable cd anyway thinking it would create some file on the hard drive. Well obviously that?s not what it had in mind because my disk drive opened, I shut the disk drive and it started saying writing data to disk. HOW could it do that with no disk. I couldn?t close it. It then said installation succesfull. What the heck. I restarted my computer to see if I had screwed up my system and it seams to be running fine. Have I screwed up my hard drive? Did the dang update install? Can I delete these firmware updte files lying around on my desktop? Please help me????

A:HP UPDATE FIRMWARE update problem?

Originally Posted by GreatNate


HP-Update FIRMWARE update problem?
I got some critical update for my Seagate 320 gb hard drive’s firmware. I went to download an process the update, later it asked me to insert a blank disk. Well I don’t have a blank disk but I hit bootable cd anyway thinking it would create some file on the hard drive. Well obviously that’s not what it had in mind because my disk drive opened, I shut the disk drive and it started saying writing data to disk. HOW could it do that with no disk. I couldn’t close it. It then said installation succesfull. What the heck. I restarted my computer to see if I had screwed up my system and it seams to be running fine. Have I screwed up my hard drive? Did the dang update install? Can I delete these firmware updte files lying around on my desktop? Please help me????



It is ok.

I dont know what happened, but You HAVE to burn the bootable disk, and then boot into it after a restart in order to update the firmware.

22 more replies
Answer Match 50.4%

Hello all I have problem that I couldn't start windows(Only in safe mode) I recently installed HDD firmware(Barracuda Green Firmware Update) My disk is st1500dl003-9vt16l AND i recently installed MYSQL "mysql-5.5.8-win32.msi" I think problem is with HDD update ? And I don't want to refresh PC because there is Imporant job on some programs left.

A:PAGE_FAULT_IN_NONPAGED_AREA After HDD firmware update

Uninstall Mysql and see if that fixes your issue. if not, I suggest you contact Seagate support because they do warn that firmware upgrades can damage data on the hard drive if procedures are not properly followed. Good luck.

1 more replies
Answer Match 50.4%

When I receive this drive will the Firmware have to be updated before use or, can that be done later on if needed? Thanks! SAMSUNG 840 Series MZ-7TD120BW 2.5" 120GB SATA III Internal Solid State Drive (SSD) - Newegg.com

A:Firmware update question on ssd

Hi,

You can update the firmware before or after, I would suggest it would be better doing it before

This version improves write performance, which is version 1.0,
click on firmware to view (you may be up-to-date):

http://www.samsung.com/uk/support/model/MZ-7TD120BW-downloads

Hope this helps

Cheers

Dave

1 more replies
Answer Match 50.4%

I have a netgear wnr1000 v2. I have been in the router settings and had it check for the latest firmware. It tells me I have the latest and that version is 1.0.0.12NA. Now, when I go to the netgear website and look up my router here: http://downloadcenter.netgear.com/ it says the latest version is 1.1.2.54. So I download it and go to install it to my router and get the error "Firmware upgrade failed. Please check your file." I know it's the right file. Only 3 files are in the installation and they are .html, .img, and .txt, and the image file is the installation one.
 

A:Router Firmware Update

16 more replies
Answer Match 50.4%

I know this might not be the place for this question but i have just downloaded a Firmware update for me modem but the files came in .rom and . bin and i am unfamiliar with these files how do i open them or with what do i open them with???

A:Firmware update for my modem

Your modem will open them. In the firmware update page, it will ask you to point to or upload the firmware file.

2 more replies
Answer Match 50.4%

I am trying to update but after some time it shows fail. firmware v 1.17 to improve touch pad

A:firmware v1.17 update failed plz help me

laptop model?which windows OS version is installed?

3 more replies
Answer Match 50.4%

Hi, I have a problem with OneLink+, where DP is not working. I believe a firmware update should fix this. The update.log which is returned from tp_onelinkplus_dock_fw.exe is: Version: 0.00.000Update result: 255Error description: Can't connect to Synaptics VMMxxxx DP hub IC The paradox is that I am trying to update the firmware to fix the DP and firmware won't update unless you have a DP already connected.  In my quest to fix this, I have downloaded many files some of those where for an incorrect model, pressumably the other OneLink. I am now wondering if I have overwritten the firmware of OneLink+ with that of OneLink. Is that possbile?  Is there any other way to fix this?

More replies
Answer Match 50.4%

Hi, i bought this network attached storage drive from Maplin Dual SATA Network Enclosure : Network Enclosures : Maplin

I tryed updating the firmware and got some message in German about how if i updated the firmware the network connection would be lost. i clicked ok and now after rebooting my drive cannot access it. i have reset it and cannot try to update the firmware again as there is not USB Port on the drive to access it directly from the computer.

Anybody have any ideas on what to do??

A:Firmware update gone wrong

Newer BIOS chips have what is called a boot block sector. When flashing the BIOS this part is not flashed. Basically all it does is run the floppy drive, and if you are lucky you will also get basic video. I have re-flashed a "dead" BIOS with this. The MB was manufactured in 1998. The first attempt at flashing failed-nothing but beeps on restart. I downloaded the correct Bios update, made a new floppy to flash the BIOS and reran the flash program. There was nothing on the monitor, just a black screen, but I could hear the floppy drive being accessed. Follow the flash utility instructions and let it do its' thing. It took several long minutes, but it worked.

I'm providing this link below. Do not hold me or vistax64 responsible.
Wim's BIOS Page: BIOS Upgrades, Motherboard identification and more...

Finally, you can approach your manufacturer of your PC or bios to purchase a replacement.

6 more replies
Answer Match 50.4%

Hi, I have an issue with an E560 that is hooked up through a OneLink Pro to two external monitors (via Displayport and DVI). Both monitors randomly go black for 10-15 seconds and then come back (not at the same time). https://support.lenovo.com/ca/en/documents/ht101596 indicates that the firmware needs to be updated; however, after downloading the .exe for the latest firmware, I can't get the file to run! After I click on it, nothing happens. There is nothing in the task manager. I've tried running as Administrator and still nothing. Has anyone had any issues with the update tool or have any suggestions? Thanks, Andrew

More replies
Answer Match 50.4%

please help me to find dvd ram uj8c2 firmware new version. Because l can't write any cd while i had upgraded to windows10.it's  shows power calibration error by nero softwear.my dvd ram current firmwear shows 1.00

A:dvd ram uj8c2 firmware update

I have the same problem. Does anyone know a solution?

1 more replies
Answer Match 50.4%

Helo,   I have issue for updating Me Frimware on my desktop Hp dc7800p small form factor whenever I want to update it an error occour in command prompt showing that'' Error: could not know the last update for Me Firmware '' tell me what can i do .. i have also upadated bios to V 1.5 ...                               waiting for reply                                          thanks.

More replies
Answer Match 50.4%

I did what it said to do in the instructions (I thought) and now my computer won't recognize the external backup. Here is the link to the enclosure.

http://www.startech.com/item/SAT352...ATA-External-Hard-Drive-Enclosure-w-RAID.aspx

How can I reflash the thing if I can't see it?
 

A:Firmware update problem

Try the external enclosure on another computer. Was the enclosure configured in a RAID configuration?
 

5 more replies
Answer Match 50.4%

Ye hi i have downloaded from Zyxels home page the latest Firmware and now my question is how do i update it? Because when i open the containing folder i have three files bin, pdf and rom. In the pdf theres just some information about what is new in the update and so on, but how do i open the two other files, i mean they are too small to be burned on a disk!!
 

A:Zyxel Firmware Update

You perform the firmware update from within the router's web user interface. Log into the router and there should be a option under one of the menus to upload new firmware to the unit.
 

3 more replies
Answer Match 50.4%

Hey. I am wanting to update firmware for my dvd burner. I know it is a NEC DVD+-RW ND 3650, but after that i have no idea how (or even if I can) update its firmware. Any help would be great thanks!
 

A:Solved: Update Firmware

8 more replies
Answer Match 50.4%

I see there's a firmware update out for the C50-30 with security updates noted in the changelog. Has anyone updated the firmware on a C50-30? Did it all go according to plan and the enclosed instructions? More importantly -- if it went wrong, how easy was it to recover?

More replies
Answer Match 50.4%

I am trying to update but after some time it shows fail. firmware v 1.17 to improve touch pad

A:firmware v1.17 update failed plz help me

laptop model?which windows OS version is installed?

5 more replies
Answer Match 50.4%

Hello, I am trying to use a Thunderbolt 3 to Thunderbolt 2 adapter (StarTech brand) to connect my P50 to a Resident Audio T4 Thunderbolt audio interface. The device is briefly detected and then disappears. I have been doing some research to resolve this issue and a few users have said that updating thier Thunderbolt NVM to 18 add compatibility with the adapter.  Would it be possible to get an upgrade from the current NVM16 to NVM18? Current P50 firmware (NVM16) link here:http://support.lenovo.com/us/en/products/laptops-and-netbooks/thinkpad-p-series-laptops/thinkpad-p50... I have already attempted to install the NVM18 firmware straight from Intel but it looks like the firmware is OEM specific. Thanks!

More replies
Answer Match 50.4%

Can't seem to find an answer to my question - Does the firmware update mean I have to reinstall windows? I have done firmware updates on other devices in the past, but not on a "boot" device, so just need an answer.

Edit: According to samsung it does not wipe HD, but just wanted people who have done an "inplace upgrade" to answer.

Edit: It worked fine through magician.

More replies
Answer Match 50.4%

i have been trying to update the driver/firmware for my pioneer dvd writer, and im having a problem running the software. the drive is the Pioneer DVD-RW DVR-108 and im trying to install the firmware version 1.20 i think its called(filename: DVR108_FW120B.EXE). i follow the vague instructions from pioneeraus.com.au and run the .exe file. and it comes up with a command promp window and i get a dialogue box pop up in front of that titled "UPGDVD" and it says "available target is not found".

i also tried to update the driver through device manager but there is no .inf file that i can find on the net so im pretty sure thats a no go.

if anyone knows a way around this problem or if there is another way to update my driver i would be very greatful if you could help.

im running xp with a P4 3gig CPU with 1gig ram and a 80gig HDD.
cheers
 

A:DVD R/RW Drive Firmware update help

First of all a firmaware update is not a "driver". all optical drives use the windows native drivers and only MS updates that. I have never seen a firmware update as you describe open a command prompt window. if Pioneer actually uses this method then you will probably have to set the command prompt to the location of your drive. ie; type the locaion ( drive letter of the drive you are updating) if your pioneer is the D drive then you would type D:\ and then press enter
 

1 more replies
Answer Match 50.4%

Hi, Samsung tells me the SSD (a Samsung) firmware updates will come from Lenovo, but I didn't see them on the driver page. The model is MZMTE256HMHP-000L1 Any suggestions? Thanks,Bruce 

More replies
Answer Match 50.4%

Hi All: Just purchased a LG GSA-4167B using a USB 2.0 connection via an USB 2.0 External Enclosure. The firmware version that came with the drive is version DL10. There are later firmware versions available, DL11, DL12 and DL13. I would like to update to the latest version, DL13. Can I do it by downloading the DL13 zip file and just unzipping it or will I have a problem because it is using a USB external connection. There are no instructions on the LG download site for a USB connected firmware update. Any insight would be most appreciated.
Thanks,
Patrick
 

A:LG GSA-4167B USB 2.0 Firmware Update ?

7 more replies
Answer Match 49.98%

I have an E420 Thinkpad; NO problems ever with the laptop...a great machine.  I ran some updates and the Lenovo update wanted to update the battery firmware; there have never been any problems with my battery (I have an extended battery), but wanted to update as recommended. - When I ran the update, I got a "the tool was unable to update the battery firmware due to an internal error"...and then it automatically rebooted. - Once it rebooted, I now get a DOS warning (on initial boot) "this system does not support batteries that are not genuine Lenovo....." and I have to hit escape to continue.- When it boots up, I get a battery icon that shows either "plugged in and charging" with a RED X imbedded in the icon.- The laptop does not recognize the battery.  Even though it was in good condition and had a 95% charge when I first ran the firmware update....the laptop will not operate without hte power plug attached.- When I go to the power manager and the battery tab, I get a "battery was completely discharged and needs to be recharged verbiage- I have tried to re-run the firmware update from the update tool, but to no success. - I have tried to run the firmware update by downloading the install .exe file and running from my desktop....to no success.- I have tried to do a system restore, but it did not work.- I have screen shots of the screens mentioned as needed. Help!  I now have a small desktop that has a closeable lid.  It will not run if t... Read more

A:Battery Firmware update - failed and now will not ...

I have the same issue.Waiting for the software update or workaround

1 more replies
Answer Match 49.98%

For some reason the firmware for thunderbolt won't update on my p70. I've tried installing from a command prompt and using the installer. Either way it seems to work but the firmware version doesn't change. I have the hdmi cable connected to a monitor and have the thunderbolt software running. I've rebooted and tried again. I've booted into safe mode then rebooted and tried again. I've uninstalled the thunderbolt controller and tried again all to no avail. Ideas anyone? Thanks in advance.

More replies
Answer Match 49.98%

Hello
Using dell inspiron 5448 with HDD 1 TB + SSD 8 GB, windows 10, 64 bit working fine.
Found the new Seagate fimware on the dell support as follows

Seagate ST500LM000/ST1000LM014 Firmware Update


File Name: Kahuna V_ZPE.exe
Importance: Recommended


Description: Hard-Drive (47.16 MB)
Release Date: 09 Nov 2016



Version: DEMM/DEMN ,A05
The installation failed on my laptop with an alarm box showing unable to identify the boot partition, please use the USB boot key or CD ISO image of this utility instead.
Confused since installation instruction said just download and it will be automatically installed.
Called Dell but the agent said nothing they could do.
Any suggestions?
Thanks

A:Seagate firmware update failed

I suggest you right click windows logo (or click yellow folder), click and expand 'File Explorer', 'This PC', and then check to see if Seagate update is either in your downloads or documents. If yes, I suggest you open the file and click 'Run As Administrator'.

7 more replies
Answer Match 49.98%

Touch pad is not working also the update firmware v1.17 keeps on failing. Please help. Btw, I'm using Aspire E 14 E5-473-304W.

More replies
Answer Match 49.98%

This is a follow up in a way. I had asked about the N-routers and how to get good reception in a large house. Based on the responses and reviews of this router Linksys WRT54GL I chose this one router to do the trick with the option of installing another one upstairs to increase coverage if needed. The price of 2 of these was cheaper than one N router or a router and repeater.

The Lisksys software is pretty lame. I was able to get my computer hooked up fairly easily but my roommate could not get online, which is more important as I am on the road all the time and he is stuck at home. I reset the router before I left so hopefully he can get himself hooked up before I get home in 2 days.

The coverage seems great. I get very good or excellent in all corners of the house. I see things about installing a second party firmware to improve it further. Any suggestions about which firmware, and details about how to update and use this firmware?

Thanks
 

A:Firmware update for Linksys WRT54GL

You need to find out why your roomate can not connect. Is it becasue of bad coverage? But, you said the coverage is great. If it is a secure network and your roomate is using the correct password/key, and if the coverage is great, then some setting issue must be dealt with in the roomate's computer.

Why do you need third party firmware for your router? That may not solve your roomate's problem, becasue as I said, it could be in roomate's computer. I have heard using third party firmware on Linksys gives much more features. One of them is to increase the power out of the router. But, again, all those feature may not help you with the problme that your have.

First do this on your computer, then on roomate's:

Start, Run, CMD to open a command prompt:

Type the following command:

Start, Run, CMD to open a command prompt:

Type the following command:

IPCONFIG /ALL

Right click in the command window and choose Select All, then hit Enter.
Paste the results in a message here.

If you are on a machine with no network connection, use a floppy, USB disk, or a CD-RW disk to transfer a text file with the information to allow pasting it here.

{credit johnw}
 

2 more replies
Answer Match 49.98%

Hello,  I am interested in updating the firmware and bios to my LSI SAS1068 integrated on my xw8600.  I would like it to remain bootable and be used in a RAID 0 configuration.  Can you provide me with any insight as to which firmware files to use and where I could acquire them...  Also what is the original LSI name for this controller.  Thanks in advance for any info you can provide.  Best regards, Johny4.51

More replies
Answer Match 49.98%

Hi, Need help where to download the latest firmware update for CD/DVD burner for my lenovo G470? Everytime i burn with my DVD a message box always pops up saying "The disc wasn't burn successfully. Make sure that you have the latest firmware for your CD or DVD burner installed, an then try again." Thanks,Jeff 

More replies
Answer Match 49.98%

I downloaded the firmware update for my CD/DVD writer. Burned it to a CD per the instructions and restarted the PC with the CD in. The PC restarts, reads the CD and then... nothing. No on-screen instructions, nothing.

The CD/DVD drive is bootable per the bios.

Any idea how to make this work?
 

A:Solved: CD writer firmware will not update

8 more replies
Answer Match 49.98%

I have a 1TB Seagate Barracuda ST1000DM003-9YN162 like the one shown on this firmware update page:

Barracuda (1TB/disk platform) Firmware Update

Because i've been having problems waking from sleep mode I wanted to update the firmware on it from my version now CC9B to its current version of CC9D. I downloaded its windows update utility and ran it. Everything seemed ok, it shut down windows, restarted, ran the updater, then it said "FAILED" in big red letters then asked me to go back to Windows. I did, everything was ok nothing got messed up.

Why did it fail to update the firmware? Was it because I didn't have CC9C and it didn't want to skip from CC9B to CC9D? Do I need to update to CC9C first? What should I do?

The update utility says that it cant be run on "RAID Systems". My system is capable of RAID but I dont have a raid setup i use ACHI. Do I need to go into my BIOS and disable something that has to do with RAID? As far as I know I have nothing enabled that has to do with RAID. Any help is appreciated. Thanks.

A:Seagate HDD Firmware update failed. Why?

I suspect that if your drive is not listed here: ALL FIRMWARE UPDATES - see here - Seagate Community Forums
Which I don't see, a firmware update is not needed nor compatible with the update.

Also read this: Does my drive need a firmware update?

3 more replies
Answer Match 49.98%

I flashed my Toshiba slim-drive SD-C2502 DVD-ROM with the latest firmware from Dell's website.

After it didn't work and it gives me the IDE #1 error before booting to Windows XP. I know I can eject before the error message but after that, it just doesn't eject at all nor detected.

I tried flashing it again but there is no drive it can detect to flash it. From the past, it seems like no way but I was hoping I can force flash it perhaps?

Any other suggestions would be grateful.
 

A:DVD-ROM not detected after firmware update...is there HOPE?!

Heh. I hate to say it, but I think you're dead in the water. Up the river with no paddle so to speak. It sounds like you're going to have to replace the drive.
 

3 more replies
Answer Match 49.98%

HI!

I put in my IP address, and get to the modem. I believe there is a way to take my modem out of the mix and update the firmware on my Linksys router, but I'll be darned if I can figure it out. I called Linksys, but they want me to sign up for 90 day tech support, and I need to spend the $$ on a new router if the firmware update doesn't solve my problems! :-/

Can anyone help me?

I have a Motorola SB6141 modem and a Linksys EA6500 router.

Thank you!!
 

A:Want to update Linsys Firmware, but modem in the way....

16 more replies
Answer Match 49.98%

I have a 4-year-old D-Link DIR 601 (cheap) router. It used to put out a little better than 42% (~38Mbps) of the speed I get hard-wired (92Mbps). Last week, that was cut exactly in half (19Mbps) after I made a few changes to the configuration which should have had nothing to do with the speed it delivers.

Questions:
Is there anything I can check in the router's config that might account for the drop in speed?
The firmware is 1.01 and I understand 1.04 is available, but the site asks if I have model A or B. I can find nothing on the labels about A or B. Where would I find that?
I tried downloading the 1.04 update for version A. It's a zipped .bin file which is not executable. How does one apply the update to the router?
The router has a reset button that resets it to factory settings. Could that solve the speed problem, or is it not worth trying?

 

A:Solved: Update firmware D-Link DIR 601

6 more replies
Answer Match 49.98%

Hello,

I would like to update the firmware of my SSD, INTEL SSDSC2CT120A3, but Google gives me results of Intel? SSD 330 Series. I don't know if my SSD model is Intel? SSD 330

A:INTEL SSDSC2CT120A3 firmware update

I would recommend you start here:
Download Intel® Solid State Drive Toolbox

1 more replies
Answer Match 49.98%

Touch pad is not working also the update firmware v1.17 keeps on failing. Please help. Btw, I'm using Aspire E 14 E5-473-304W.

More replies
Answer Match 49.98%

i was trying to update my SONY DVD Drive fireware yesterday,
but it failed, i mean can't complete process.

After i reboot, theres no Drive display in MY COMPUTER &SYSYTEM Properties(Device Manager) and the DVD Drive's power bottom is not working too(can't eject/close)
CAN ANY ONE TELL ME HOW TO FIX???????????
THANKS

My DVD Drive
Sony DDU-1621 DVD-ROM 16X/48X
 

A:DVD DRIVE Firmware update Fail???

7 more replies
Answer Match 49.98%

I took a firmware update downloaded from Windows Update. The machine shutdown and began flashing the bios. It then restarted and now does not boot at all. It does not even get to the BIOS. It simply restarts and goes to a black screen with no messages or failures. Is there  a way to flash the BIOS and/or Firmware from a USB key or DVD? Regards,J.M. Wiley

A:C40-05 Firmware Update Failed and Machine won't bo...

Welcome to the Lenovo Community !
 
Sorry to hear of the problem you are having.  Are you sure you got a BIOS Update from Windows Update?  If you did, that is a scary thought.  Windows 10 is good for giving you OS and driver updates whether you want them or not. Giving a BIOS Update is kind of over stepping their bounds IMHO.
 
Have you tried this.....
1. Unplug the charger / adapter. 2. Press and hold the Power Button for 15 seconds. 3. Plug in and power up the system to see if the problem was resolved.
 
If that didn't correct the problem, can you access the BIOS Setup by repeatedly tapping the F1 key when you first power up the computer.  If you can access the BIOS Setup then your problem is most likely an operating system problem with a driver update Microsoft gave you. 

1 more replies
Answer Match 49.98%

Hey,

I just had a quick question I have a LG CH08LS10 Blu ray drive and I have been having glitches with some Blu Rays namely Terminator Salvation and The Dark Knight they run choppy and stutter. All of my other Blu Rays run fine.

Anyway the software that came with the Blu Ray Drive came with the LG Tool Kit. When I first got the drive I used it to auto look for firmware updates. It found one update to make the drive compatible with Windows 7. It says that the update was successful but I'm unsure whether that's the case or not as I can't find out where to find out which firmware I have right now.

So I have tried everything to fix the stuttering issue with the two Blu Rays. I've updated Java, upgraded the Blu Ray playing software, updated graphics drivers, switched off tons of start up programs and still Terminator Salvation and The Dark Knight stutter. It doesn't make sense because TS spikes at 100% percent CPU usage all the time and 2012 is 50% percent.

So should I just go to the LG website and manually download the firmware update? Or will that damage my drive?

Compaq Presario Intel Celeron D 3.46GHz
Windows Vista Basic SP2
2GB Ram
120GB Hard Drive
Nvidia BFG GeForce 9500 GT 1GB PCI-E 2.0 Driver, 197.45
BFG 450 Watt Power Supply
Samsung p2250 Monitor digital driver
16X BD-ROM LG Ultra BLue
Alhena 5 Motherboard
 

A:How do you know if a firmware update actually installed properly?

Nero Info Tool should tell you the drive's firmware: http://www.nero.com/enu/support-nero8-tools-utilities.html
You can also run that same firmware update utility and I think it tells you if the firmware versions and if there's a newer version.

You can try the WinDVD trial: http://www.corel.com/servlet/Satellite/ca/en/Product/1189528458632#versionTabview=tab1&tabview=tab4

You have a weak CPU and that may be the problem.
 

3 more replies
Answer Match 49.98%

Samsung has recently posted firmware update EXM03B6Q for the 850 Pro on the download site.
I was unable to update via Magician so downloaded the ISO and ran it from a USB drive.
I was one of the lucky ones who didn't update to EXM02B6Q in Feb of 2015 which was a total disaster.
The update worked without any problems and speeds have not changed at all.
There is also a PDF installation guide for those who like to read first.
Don't forget to image the SSD first just in case. I did not, however loose data but better safe than sorry.

Tool & Software | Download | Samsung V-NAND SSD

Cheers

More replies
Answer Match 49.98%

Hi,

I've noticed a slow down in my Plextor PX-708A and thought that installing the latest firmware would a good idea.

The firmwares listed on the plextor site only listed for:

* PX-712A/SA/UF

* PX-708A2/UF2

* PX-708A/UF

* PX-504A/UF

http://www.plextor.be/technicalservices/downloads/firmw_dvdrec.asp?choice=DVD-Recorders

As far as i am aware my drive is just a Plextor PX-708A drive.
What are the 708A/UF 708A/UF2 drives??? How do i know if my drive is one of these?

Matt.
 

A:Need to update firmware? Plextor PX-708A2/UF2??

Looking at this site:

http://www.plextor.be/products/dvd_recorders/px-708a.asp?choice=PX-708A

You'll find that the "A" model is the IDE internal drive, and the UF & UF2 models are external USB/Firewire drives.

However, following the link from PX-708A to firmware upgrades did not show a download for the "A" model, only for the others.
 

2 more replies
Answer Match 49.98%

Last night I went ahead and took the plunge ... Updated the Firmware on my Archos 70 Internet Tablet 250GB (2.1.3 - Android 2.2.1).

My tablet still worked after the update. Slower than before though.

This morning I found out that I can't get online!

None of my four radio apps work (they all worked fine before).

Bible.is no longer works.

All three of my browsers no longer work.

Firmware Update doesn't work (can't connect to the Internet).

Wi-Fi shows that my Archos is connected to my Internet service. My son and I are both online with our computers, so there is nothing wrong with our Internet connection.

Looks like I have no choice now, but to reformat the Archos and start all over again (for the 4th time!!!!) .... That will be very time consuming, as I will have to download all of my many apps all over again, and then reload all of my files all over again ....
 

A:Android Firmware Update Problems ...

If your wireless network is encrypted, have you tried resetting the WPA key?

Just curious.
 

2 more replies
Answer Match 49.98%

I have an ADATA S510 120gig SSD, i tried downloading the Firmware upgrade tool seen on this page

S510 SATA 6Gb/s Solid State Drive, Download, S510, 500 Series, Solid State Drive, Welcome to ADATA

I opened the tool and it didnt find my SSD drive. I then downloaded the file itself to try and manually install it but it is a "VIC" file, i dont even know how to open it.

Does anyone have experience with updating their firmware on these SSD drives? What am i doing wrong?
edit: after digging around on my machine i found that i have firmware 3.3.2 which is apparently the latest firmware out there right now (i didnt know that till i just found this info out, this machine is 2 weeks old)

A:Can't update firmware on ADATA S510 SSD

I started my PC with a Linux live DVD (Knoppix) because my ADATA S510 SSD Device is my boot device and device with OS (W7).
So I run the Linux version of the updater (you must be root!) and all worked fine!
But: please check the signature (for example 22739) - it has to be in the filename of the firmware update!
Good luck

PS: my drive was not 3.3.2....now it is! I hope my problems (bluescreen) are gone now!

2 more replies
Answer Match 49.98%

Hi - I was able to solve connect issues by updating firmware on my wireless router - wifi weirdness

But now my printer is not available (to this or any other laptop/macbook on the network.

How do I install/re-install my brother 9840CDW to my little network here?

Help! I need it! Thanks

A:(Re-) Installing a printer after firmware update

Have you disabled your network then re-enabled it & Also reset your router ??

8 more replies
Answer Match 49.98%

Hello,
I am trying to update the firmware of my iriver T30. I am using the tool provided by iriver. I am able to delete the firmware from my T30 but I cannot install the new firmware on the T30. It just hangs, and I have to close the program after many hours, and kill the process on my PC and try again with no luck.
Can someone help me?
Thanks
Margarita
 

More replies
Answer Match 49.98%

Good Morning All,

I've posted to this site a few times, with excellent results and fantastic support from the members, thanks so much for all your help.

Here's a new one:

My Crucial C300 has firmware 001....needless to say I've been having some issues, BSOD's, etc...

So, I download all the updates, 1 > 2, 2 > 6, 6 > 7....and follow the Update Guide to the letter...

All is good and fine until I have to set my machine to IDE in order to install the update.
BIOS SATA controller says "AHCI or RAID"....no other options.
Cannot update the firmware. NO drive detected. Tried RAID, just in case. Nope.

I have a Dell XPS 9100, and have an ASUS U3S6 as well, but connected the SSD to the motherboard as the guide said to do....tried all the ports 0-3....nope.

I've set aside the time and patience to update the firmware to 007...as well as reconfigure some things with my system, 'housekeeping', if you will...

How do I get my machine into IDE mode? (And then back into AHCI when the updates are finished) Did I miss something in BIOS?

Thanks again.

A:Trying to update firmware on Crucial C300...

Just a note of caution, I would recommend doing a full system image before updating the firmware especially since you are having issues.
I am not advocating updating the BIOS on the Dell, but have you checked Dell's website and the associated release notes for any/all Bios upgrades?

4 more replies
Answer Match 49.98%

gang I've been web-searching for updated firmware or a way to do it on Hitachi travelstar internal 2.5" hdd... I have one that is producing frequent read errors, but running chkdsk the drive is 'squeaky clean' from a surface standpoint. I was hoping I might update..... can't find a thing

this drive failed the HP builtin [BIOS] HD tests, short and long, and failed the HGST diags tests, short and long [though the SMART status was all rosey ] Specifically the tests point to read-access failures which produce a string of Windows 7 system 'critical' events since the OS timing is scrambled by fetches that return no response.

nagging in the back of my brain is an ugly scenario: what if the issue is with the Mboard component? what would clue me in that the drive interface is at issue ? disc is a lot more likely I agree but it just doesn't feel like an ordinary disk fail

A:Any way to update Hitachi Travelstar firmware?

Hi there .. The place to look for a firmware update should be the HP website .. Not sure that it will help much though

1 more replies
Answer Match 49.98%

Hi!

It took me almost one hour to find this firmware update for my ADSL modem so that's why I uploaded it to Skydrive and make it hopefully a little bit easier for you.

My modem kicked me of the web a few times every day and then it also had a "broken internet connection" so that there was a little yellow notification triangle on the network adapters icon even if the "internet providers" signal was ok it couldn't connect...

Any how, I updated the firmware and I have been running it for a few days now and no connection problems.

Here is the link and there is also a manual included (and in the comments you can see a really short description on how to update the firmware).
 

More replies
Answer Match 49.98%

I tried to update my dvd rw, but this is what I get.
 

A:Unable to install the firmware update

Make sure that all other ATAPI devices are disconnected, if possible. If the drive is no longer under warranty, try the PS0B stock flash from CodeGuys. Using this patched version may invalidate any warranty.

But, what is the reason for the upgrade? They just as often as not lead to problems.
 

2 more replies
Answer Match 49.98%

Hello, I had no problems with the touchpad in my first two months of owning this computer. Recently when I try to use the touchpad, the cursor bounces all over the place and I have no control over it. This is espescially annoying when I am at work and need this to work correctly when I am gathering data in an excel doc. I noticed there was a 1.17 firmware update for the synaptics driver in the care center, but when I click to install it will run for a second and then say "failed". Just updated BIOS and every other driver I could think of but it makes no difference.

A:Touchpad firmware update VN7-592G

Hi ! Have you trying Unistalling the driver for the Touchpad? Must of the times unistalling the drivers and restarting your unit will actually fix the issue. If you access the Device Manager (Press Windows key +X)> Select Device Manager > Mice and other pointer device, Right Click> Unistall> Restart. Some updated on Windows sometimes will disable the proper Drivers for your unit. Hope this could help you!  

2 more replies
Answer Match 49.56%

When trying to download the update from 
downloads.dell.com/FOLDER03005632M/1/LMT-256L9M-HM8110D_ZPE.exe , I get:
Server Error
404 - File or directory not found.
The resource you are looking for might have been removed, had its name changed, or is temporarily unavailable.
Brought this issue up a few days ago on Dell's Face page and they said everything is working fine. No it isn't. I don't have ANY problem downloading any other file - only this one. They keep telling me to try another browser, try this, try that and NOTHING works! Tried from a different computer and it STILL isn't working.

A:Problem downloading firmware update for LMT-256L9M SSD

Try here:
http://downloads.dell.com/FOLDER02163459M/6/LMT-256L9M-HM8110B_ZPE.exe

1 more replies
Answer Match 49.56%

Does anybody (else) have a PM851 SSD in their Toshiba Z30A? (Windows "Device Manager" will show that).

It has come to my attention that these drives have a serious defect in their firmware that affects performance.
Search Google for "840 EVO firmware performance" to find the fixes for the Samsung's retail version.

Is there any firmware update for the PM851 SSD?

My Toshiba Z30A shipped with such an SSD.

A:Portege Z30A - firmware update available for PM851 SSD?

I?ve upgraded my machine with 840 EVO and I?ve installed ?S.... Magician? software so I was informed about latest firmware update and I?ve installed it.
I?ve checked manufacturer?s page for SSDs support but I didn?t find anything for PM851 SSD so I think firmware update is at the moment not available.

6 more replies
Answer Match 49.56%

friends I'm installing a fresh samsung 840 120gb. i thought i could put the ssd on sata 1 [not zero] and get firmware via magician on my windows 8 lab mule. no dice. apparently magician ONLY wants to see the ssd on sata zero. it can pull up the drive, but none of the controls work.
soooo... I'm thinking I'm going to have to go with the drive 'as is' to install 7 on a notebook, then as first order of business go pickup the firmware update and execute it.

will this result in sub-par arrangement? best I can tell the fw update is non-destructive.
is there another way?

A:samsung ssd: will firmware update harm anything? magician no use.

friends i have a new samsung 840 to replace a failing drive in a hp notebook.
i wanted to update the samsung firmware first, then do the install of windows 7 x64 but using the samsung so-called Magician, trying the drive on sata 1 [instead of 0] it still cannot properly register the drive. all I get is the SMART info - everything else is neutered. illogical... how does samsung want to update firmware? AFTER the os is installed?
a little guidance would sure be appreciated.

8 more replies
Answer Match 49.56%

Hi,I am having this error message on my hp dc7800.2210 - parameters frame errorme bios extension module execution has haltedupdate bios or management engine firmware if problem persists.2206 - end of post heci failuresystem halted. power cycle the system to reboot. now how can i update bios from usb

More replies
Answer Match 49.56%

Hi

I am experiencing intermittant connectivity issues and am wondering, whether amongst other thing I should update firmware. ( Have downloaded the microsoft patch) For some reason my internet connection drops every 2/3 days

The version of firmware that I can see is running from the DLink control panel is R 2.01.b5nz. I have no idea if this is the latest. If I need to update, does anyone know how I should do it. I am rather reluctant to do this as I don't wont to "bomb" my computer.

Many thanks

Grandpa

I have been to http://www.pchell.com/support/limitedconnectivity.shtml.
 

A:ADSL D500 Router firmware update

6 more replies
Answer Match 49.56%

I would like to update a D-link DIR-655 router firmware
I downloaded an update that is a zip file that contains
a single *,bin file. How do I update this router with this
file? I would like to also install program called sharepoint
so I can share drive on a USB port that is on that router.
Any suggestions on how to update this router and use
a put a network drive on a USB on this router? First I need to
know how to use the bin file.
Thank you,
 

A:Update D-Link DIR-655 Router firmware w/bin file

6 more replies
Answer Match 49.56%

I seem to be in a loop while upgrading from a Pentium G840 to an i3770 K on an Intel DH61WW motherboard.
It seems that I need version 8.x of Intel Management Firmware and I can't get to update past version 7.1.52.1176
According to this page, I need version 8.x to continue for updates to use Windows 8 & 8.1

So far, I have had the bios version update to
BEH 6110H.86A.0048.2012.1105.1520
I had the i7 installed but it acted confused. So I reinstalled the Pentium and still nothing works as far as updating the Intel Management Firmware .
According to this page I am ready for 3rd Gen i7 but not unless Intel Management Firmware gets updated first

Board


DH61WW

3rd Gen-Ready AA#s

AAG23116-206
or later
3rd Gen-Capable AA#s

AAG23116-204
3rd Gen-Transition BIOS version

BEH6110H.86A.0035
3rd Gen-Ready BIOS version

BEH6110H.86A.0041 or later

 

A:Intel Management Firmware Update help needed

Did a BIO Recovery, updated to BIOS 0099 then BIOS 0120

1 more replies
Answer Match 49.56%

My notebook is one of the first to come out of the assembly line and came with firmware 1.02.There's 1.08 BIOS that came out, so I tried to update it from Windows 7.  It took a long time, but it completed and the tool said to reboot.  That's all it said as far as I remember. Upon reboot, it started to give beep code.  I don't remember which it was, but it was something like 1-long 2-short or 2-long 2-short.  It kept at it for a while and I got tired of it, so I pressed and held the power button to kill it and then restarted it. This time, it got into BIOS, which said it was updating USB Type-C Controller Firmware from v12 to v13.  This FAILED and gave me the option to "reboot and try again."  I picked that, but it never retried. I didn't feel comfortable with this, so I flashed 1.08 BIOS again, this time from within the BIOS using a USB-stick (\Hewlett-Packard\BIOS\New\N73_0108.bin).  It went through much quicker than in Windows and at the end, it actually warned me that the machine may beep for a while after reboot.  Umm, thanks for the warning, now that it's too late.  Why didn't Windows update program give me the same helpful warning? Anyway, the machine rebooted, but it did nothing to try to update USB Type-C Controller Firmware.  I'm guessing it set a flag somewhere saying we're already at 1.08 so there's nothing new to do. When BIOS configuration is dumped using BiosConfigUtility.exe, it shows US... Read more

A:Failed USB Type-C Controller Firmware Update

The 1.11 BIOS update posted 31 March 2016 corrects this issue.http://h20564.www2.hp.com/hpsc/swd/public/detail?sp4ts.oid=7815285&swItemId=ob_163435_1&swEnvOid=4192#tab4 

4 more replies
Answer Match 49.56%

I own a S440 and I like to upgrade the firmware for the Seagate SHDD ( http://support.lenovo.com/de/en/products/Laptops-and-netbooks/ThinkPad-S-Series-laptops/ThinkPad-S44...) There is no bootable iso or anything I can use directly. At least I need the correlation between the extracted *.LOD files and the compatibles HDD. Seagte does not have any further information about this firmware upgrade. (https://apps1.seagate.com/downloads/request.html  , Part Number: 1EJ162-073) I guess some OEM restrictions.FreeDOS did not work. with this guide you could at least try to flash the firmware under *nix:https://github.com/jandelgado/general/wiki/Firmware-update-of-Seagate-harddisk-using-Linux Which firmware file do I need? (ST500LM000-SSHD-8GB)Why lenovo do not release at least a bootable WinPE for flashing firmwares?




Thinkpad T500 2082-52gHDD changed into SAMSUNG HM500LIMicrosoft Windows 6.1 Built 7600 - Windows 7

More replies
Answer Match 49.56%

On my P50, when I check for updates with Lenovo Companion, it always tries to install Intel Management Engine 11.0 Firmware, and it downloads, says it failed when the little black command prompt opens, reboots, and then the update history said it was installed, yet Intel Management Engine 11.0 Firmware keeps popping up as an update.  What is this update supposed to do? Why is it failing? Everything else on this computer is up to date.

More replies
Answer Match 49.56%

First off, why is there no forum for server/network related topics? Anyway... Does anyone know where I can download the firmware and the update utility for HP VC FlexFabric 10Gb/24-Port Module. All documentation I can find, including documents sent to me by HP themselves in the last week, say I should go to http://www.hp.com/support/vcHowever that page no longer exists.Where should I be going now? Thanks in advance.

More replies
Answer Match 49.56%

Firmware 1.32 for OCZ Sandforce drives, ( Vertex 2, Vertex LE, Agility 2) is available.
If you want to see what firmware you're currently running on, go to Device Manager and follow to here:


Changelog is here: Release Notes

Quite extensive changelog this time around. Looks like it's worth updating to. If you update, read all the instructions and warnings.

This is the OCZ toolbox update.
OCZ Technology

There's also a standalone.
Guide Sandforce Firmware update 1.32 for OS/System drives

General Discussion Firmware 1.32 Released at OCZ.com


April 20, 2011

Firmware 1.33 released.

Release Notes

Newest toolbox version from download link above - 2.36

Updated from my other non system Win 7 drive. Went just fine.

A:OCZ Sandforce Drive Firmware Update 1.32/1.33 released

Thank you sir!

Have you done your update yet? Thoughts?

Thanks.

9 more replies
Answer Match 49.56%

Hi. I ran the Samsung 840 EVO Firmware update that was provided because of the degrading problem said to be with the product.

It went all the way through and said complete. There were no problems or interruptions there. I closed the application and rebooted my machine.

The computer will get to the windows screen but right when it is supposed to go to the login it goes black and the monitors stop detecting a signal. It just sits at a black screen.

The scary thing is that when i try to run a recovery all executables associated with a given recovery error out. I.E. StartRep.exe fails to run. Trying to load previous working fails to run to. They get memory exception type errors!

I put in the windows 7 disc and have had it come up with "hit key to boot from cd or dvd". all repair attempts are the same as above. They fail the same way.

The only thing I have not figured out is how to get the machine to load into safe mode. i have been hitting F8 and doing what I can but I get no such options. My options are only the repair dialogs or boot normally. I do not understand why this machine has never given me a choice to boot to safe mode. How can I get that to work?

Please help! Is there anything I can do? I can't find any samsung forums or info.

Windows 7 64 Ultimate.
Asus X99 Deluxe.
Intel 5960X 3.0 x 8 core
G.Skill Ripjaws 4 Series 4 x 8gb (32gb) DDR4 2400
Samsung 840 Evo 500gb SSD
Corsair RM1000 1000wPSU
Corsair H100i
Nvidia 780GTX

A:Samsung Evo 840 Firmware update - Now windows won't boot.

What degrading problem ? Samsungs are the best IMO, what did you think upgrading the firmware would help ? Or what did Samsung say it was for ?

How old is the drive, how often is it used ?

9 more replies
Answer Match 49.56%

linksys wrt54g v3.1 firmware update will not load.

I unzipped the file, held the reset for 1 minute, unplugged for a minute (and then did some emails - would that be a problem?) then went to admin/firmware, selected the file, clicked "update" the web page, for 20 minutes, read:

This webpage is not available.

The webpage at http://192.168.1.1/upgrade.cgi might be temporarily down or it may have moved permanently to a new web address.

More information on this error
Below is the original error message

Error 2 (net::ERR_FAILED): Unknown error.

Any advice? They want 30 dollars to help me update this router: I don't have that.

I'm running XP.

Thanks in advance,
SKS
 

A:Solved: router firmware update will not load

Try going to 192.168.1.1 and logging into the router's configuration pages normally. The firmware upgrade page is described on page 41 of this WRT54G User's Guide
 

3 more replies