Tech Problem Aggregator

Satellite U920T - front/back cam + touch screen + win button doesn't work

Q: Satellite U920T - front/back cam + touch screen + win button doesn't work

I have the issue that the touch screen + front camera + back camera + windows button on the screen are not working.

I tried installing the display/graphics drivers but that did not helped.

I bought this laptop from Saudi Arabia and it is still under warranty but I am out of country so i cant claim the warranty as well.

someone please sort out this issue and tell me the solution or tell me what i should do?

Help will be really appreciated.
some details about my laptop:

Toshiba Satellite U920T-B919.
windows 8.1 update 64 bit.

Thanks,

A: Satellite U920T - front/back cam + touch screen + win button doesn't work

Since you mentioned different issues with your notebook, I think that in this case its advisable to recover the notebook back to factory settings just to check if all these problems are related to system problem.

Regarding the webcam: the Windows 8 /8.1 already contains the webcam drivers and therefore additional webcam driver installation isn?t possible. Additional webcam driver does not exist simply.

From my point of few the whole description smells a little bit like a hardware problem of the upper slide part where the touchscreen is part of.
The win button as well as the both cams are located there and probably there is some lose connection between the two parts (touchscreen and keyboard)

Anyway, as I said above, its advisable to recover the notebook to factory settings just to ensure that the system isn?t the troublemaker.
In case of hardware problems, you would need to get in contact with service available in your country.

7 more replies
Answer Match 101.4%

Hi there,

Today my laptop (windows 8.1) ran out of battery. Later when it was charged again, only a black screen with a cursor appears. Additional the power button does not work. When I press the power button the laptop does not shut down nor boot again, just the black screen with the cursor appears again. Alt+Ctrl+Del does not work either... I don't know what I can do else. Can anybody solve this problem?

Thank you very much for your help

More replies
Answer Match 78.6%

Please read this fully before replying with your copied and pasted replies.

My touchscreen used to stop working but was always fixed with a machine restart.
Now it's not working at all and *I have already tried everything posted elsewhere in this forum*.

I have tried changing the battery power settings, trying to update drivers (not exactly sure which is the right one though!?).

Please can someone help because it's a new machine and it is very frustrating.

Serial Number: 7D054633H
Model: Toshiba Satellite U920t-10P PSUL1E-01900JEN

Many thanks in advance.

A:Touch screen not working for Satellite U920t-10P

> Please read this fully before replying with your copied and pasted replies.
IMHO I don?t think that someone here in the forum doesn?t read the messages before replaying?
I hope this part of your message is just a result of frustration due to the notebook malfunction...

Back to your issue:
> I have already tried everything posted elsewhere in this forum.
?and what does this mean? What did you try exactly?
Did you system reset and factory settings?

If not try it and in case this does not help you the notebook?s hardware might be affected which requires further hardware checks by authorized service engineer

9 more replies
Answer Match 78.6%

The touch screen on my Satellite U920T does not work since a couple of days back.
I cannot find any settings for touch or any touch device (apart from the touchpad) in the device manager.

I'm unsure exaclty when it started to malfunction.
I installed the Windows 8.1 some months ago and had some problem with the wireless card in the beginning, but the issue with the touch screen just appeard this week.

Which Toshiba driver controls the touch screen?
Is this a hardware or software issue?

A:Satellite U920T - Touch screen not working

Hi

To be honest there are no special drivers to control the touchscreen.
The driver is provided by Windows system.

I think you should recover the notebook back to factory settings but I?m afraid this will not solve the issue. It smells like hardware related problem since I found some threads here in this forum about the touchscreen malfunction and mostly the issue could be solved by service agents.

By the way: Before running the recovery process try to configure the pen and touch display.
Go to control panel (Windows key + X -> control panel) -> ?Tablet PC setting?.
The first tab ?Display? contains options like ?Configure the pen and touch display?.
Here you should be able to start Setup and to identify the touch screen.
The first option should contain ?1 internal LCD?
At the bottom you could find button to calibrate and reset the settings for this internal LCD.

19 more replies
Answer Match 108.78%

My touch screen as stopped working. It was working fine, screen went to sleep and when I woke it up the touch screen had stopped working. Not sure if I may have push or touched something to lock or deactivate the touch screen?

There is a function key to lock the touch pad (mouse pad) on the keyboard but nothing obvious for the screen.
Thanks

A:Satellite U920T - touch screen has stopped working

If you restart Windows does it work again?

If not, you may need to send the tablet to an authorized Toshiba repair center.

9 more replies
Answer Match 107.94%

Just opened my new u920t-117, my first time buying a Toshiba, 5 mins in and excitement has started to turn to worry.

I really hope its me doing something simple wrong, or at worst a software issue.

At no stage has the touch function worked (neither in tablet or laptop mode).
In control panel --> System under Pen & Touch it says "no pen or touch input is available for this display" just like my last computer that had no touch screen.

Does this mean there is a problem with the driver or something.

Also it seems when i click shut down it shuts down and about 5 secs later starts up again.

A:Satellite U920T-117 - touch screen is not working & shut down restarts

Hi stephen





> I really hope its me doing something simple wrong, or at worst a software issue.



I’m afraid the worst case is a hardware malfunction and I guess your Satellite U920T touch screen malfunctions.

I read in other thread about the similar issue and it looks like the service engineers needs to be contacted in order to solve such touch screen problems.

I don’t know if you could ask your dealer for a unit replacement but in case the dealer would not replace the notebook, get in contact with an Toshiba ASP in your country to fix it.

2 more replies
Answer Match 93.24%

hi
i have dell inspiron n5010
i want to disable its touch pad but cant figure it out
there is a touch pad disabling button (right beside f12 key) but it doesn't work

can anyone tell me how to do it cuz it gets really irritating sometimes.

thank you in advace
 

A:Touch pad disabling button doesn't work

Touchpad problem

Hi. I don't know about a button to disable the touchpad on a laptop, but there is a free program that will do the same thing, so you can type away, and your arm won't move the cursor around. Try http://code.google.com/p/touchfreeze/
 

9 more replies
Answer Match 90.72%

The touch pad of my Satelite U920T-100 works when the lap top is started up, but some 10 seconds after I have logged in the touch pad does not work anymore.

I have tried all tips as posted at the FAQ's:
- disconnected all other devices
- external mouse works, but once this has been diconnected the touch pad remains "dead"
- FN-F9 gives no result
- checked touch pad settings: nothing abnormal
- removed and reinstalled touch pad drivers three times: no result, problem still exits.

When the lap top is started up in safe mode the touch pad works again (and continues to work), so probably some program is blocking the touch pad when the lap top is started up normally.

Don't know where to go from here. Does anyone have a suggestion on how this problem can be fixed?

Thnx & grtz,
Rein

A:Satelite U920T-100 - Touch pad does not work after log in

The problem disappeared for one day (and the touch pad continued to function) for one day after installing the BIOS update from 1/16/2014. However, the next day the same returned: approx. 10 seconds after logged in the touch pad stops to work....

Does anyone know how this problem can be fixed?

4 more replies
Answer Match 89.88%

Hello i'm new here :)

i bought a new Toshiba Satellite C70D-B-108 but the Fn button doesnt work. Does somebody know i can fix it? The laptop runs on Windows 8 with a "classic shell".

A:The FN button doesn't work on my new Satellite C70D

Check please settings for ?Function keys mode?. There are two ways to use F keys:
-Special function mode ? use F keys only
-Standard F1 ? F12 mode ? use FN+Fx key

Check the settings please.

By the way: do you use original preinstalled Win8.1 that you got with your machine?

2 more replies
Answer Match 88.62%

I have problem with my wireless switch. Take a look at this [picture|http://bildr.no/view/591716]. It says "bryterstatus: p?" which translates (poorly) to "switch status: on".

Although, when I press Fn + F8, nothing happens. All the other FN + "random button" hotkeys work though. In other words, I can't connect to my wireless. I know that it works, because I can connect with my iPhone. There's also nothing wrong with the connection, I've tried to deactive / active on and off. Tried to restart my laptop. I've even downloaded new drivers. Nothing seems to work. How can I turn on the switch?

Best Regards,
Miguel Rodrigues

A:Satellite Pro L500 - Wireless button doesn't work

Hello Miguel

Has your notebook ?factory settings? or you have changed something?
Have you installed own operating system or notebook still has original preinstalled operating system?
Is WLAN card installed and listed properly in device manager?

WLAN usage is so simple and by ?default? it must work properly. The same principle is on all Toshiba notebooks same. When you want to use WLAN you must move WLAN switch to position ON and use FN+F8 key combination to enable WLAN card. That?s all.

What you can try is to reinstall Value added package?

7 more replies
Answer Match 88.62%

After I login at certain sites and get to the next page, the BACK button doesn't work. If I hit the back button twice it takes be back TWO pages and goes past the login page. Then if I hit FWD, it jumps past the login page again.

It's as if IE is trying to "protect" me from showing that login page again, but at some sites I need to re-access it after logging in.

This started happening after the following took place..

I uninstalled a trial version of Zone Alarm Suite and then installed the free Zone Alarm firewall and AVG anti-virus.

I have no idea how or why either of those would affect this, but it's a strong coincidence to say the least. I've messed with every setting I can think of in IE, Zone Alarm, and AVG and I'm stumped. And turning off ZA or AVG doesn't help.

Any ideas?

A:Back Button Doesn't Work - Ie

Welcome to Bleeping Computer Timmer. Can you provide some details about your OS and which browser you are using?

8 more replies
Answer Match 87.78%

On some(most) uses my back button doesn't work.  I have to go out of the program and start all over.  Even rt clicking on back doesn't work.

A:windows 7 back button doesn't work

Hi mmadyda and welcome,
 
can you tell us what browser you are using when this happens ? Or does the problem exist with all browsers.
 
What 3rd party toolbars have you got loaded? Google, Yahoo? Anything else?
 
The only time the back button doesn't seem to work is when there is an intermediate redirection page, so when you click back you are returned to
the URL that redirects to the page you were on again. If you use the little drop down arrow next to the buttons you can skip back 2 pages to work around this.
 
Hope this solves your issue
 
Regards............

1 more replies
Answer Match 87.36%

Since i installed MS office 2013 the touch screen function is not available any more in the system settings.
Who can help me?

Best regards J?rgen

A:Satellite u920t - Touchscreen does not work

Hi Juergen

Which machine do you have?
Have you tried to remove Office and test functionality again?

6 more replies
Answer Match 86.52%

hello everyone
I have upgraded to win 10 on my notebook & since then I lost the touch ability of my screen, it's working now as a regular display monitor.
I've been searching for many weeks on the net for a solution but I realized that Toshiba doesn't care about solving the issue so anyone have reached a solution? it seems to be a driver or a software issue related to win 8.1 & 10.

A:Satellite U920T touchscreen does not work using Windows 10

Hi there.

Same as Dr. Joe.... I also upgraded to Windows 10 and lost touch screen and also camera. I reverted to Windows 8.1 and I still have no Touch Screen. I appear to have lost my HID Touch Screen drivers as well.

Anybody got any thoughts on how to restore the touch screen drivers? I can't find them in the Toshiba driver download section after hours of research.

1 more replies
Answer Match 84%

I just purchased this laptop yesterday, 9/12, and it was working perfectly fine until today. I was working on it and the touch screen stopped working so I can only use the keypad. I'm wondering if something went wrong with the laptop or if it can be easily fixed!!

More replies
Answer Match 84%

Hi,thanks a lot from hp companyI bought hp envy k212ne last week and I removed ubuntu and I installed windows 8.1 and I downloaded all of the drivers for my laptop from hp support .In addition before I install drivers in my laptop , I saw pen and touch in my control panel , but now it isn't there.Then I went to device manager (Human Interface Devices ) but I didn't saw HID-COMPLIANT TOUCH SCREEN ,there.So I need your help .Plz help me.

More replies
Answer Match 84%

I just purchased this laptop yesterday, 9/12, and it was working perfectly fine until today. I was working on it and the touch screen stopped working so I can only use the keypad. I'm wondering if something went wrong with the laptop or if it can be easily fixed!!

More replies
Answer Match 84%

Hi,thanks a lot from hp companyI bought hp envy k212ne last week and I removed ubuntu and I installed windows 8.1 and I downloaded all of the drivers for my laptop from hp support .In addition before I install drivers in my laptop , I saw pen and touch in my control panel , but now it isn't there.Then I went to device manager (Human Interface Devices ) but I didn't saw HID-COMPLIANT TOUCH SCREEN ,there.So I need your help .Plz help me.

More replies
Answer Match 84%

The touchscreen on my Yoga 260 isin't working. I first noticed this problem when the screen was acting wierdly. When you tap on your yoga a light circle appears and fades over time to mark or show where you tapped and when you swipe a trail or tail appears behind of where you swiped then disappears over time. So when I opened my Yoga these taps and swipes were appearing all over the screen ramdomly in a very rapid pace. So I restarted my Yoga and saw that the swipes and taps were still there. So I chose to restart the Yoga again and the taps and swipes dissapered. After that I noticed that the touchscreen became unresponsive but the computer runs as normal butthe screen is unresponsive. Before I discovered the problem I could remember dropped the computer a small height but caught it. If there's a solution to this problem I'm happy to listen! Thanks. 

More replies
Answer Match 83.16%

Hi Guys...I'm using the Lenovo multi touch driver for my X61T. With Windows 7 build 7000 the same driver when I wake my laptop from sleep the touch screen works. Starting with build 704x (i can't remember the exact build but it was the first leaked x64 build) when I wake the machine from sleep the touch screen doesn't work (both pen and finger touch)

I have tried to change USB settings but I haven't seen any fix. A restart of the machine means the tablet works again. Any ideas about a patch until Lenovo makes new drivers for Windows 7?

A:Touch Screen doesn't work out of sleep

There is a registry patch for better USB connectivity after waking from sleep, available from Lenovo.

Lenovo Support & downloads - Registry patch to improve USB device detection on resume from sleep for Windows Vista - Notebooks

How's the touchscreen working for you? Hope it's great! I don't like touchscreens because the screen can heat up and flicking your finger around on it can really burn.

4 more replies
Answer Match 82.74%

The screen has stopped working on a relatively new U920t. It displays in second screen mode on the TV but the actual screen does not light up at all in either laptop or tablet mode.

Any help in this matter would be appreciated.

A:Satellite U920T screen has stopped working

> It displays in second screen mode on the TV but the actual screen does not light up at all in either laptop or tablet mode.

This means that there is nothing wrong with the graphic chip on the motherboard but probably the connection between the display and motherboard isn?t OK or maybe the internal display malfunctions.

Fact is that this is a hardware problem and you should contact the Toshiba authorized service provider in your country to get it fixed.
If warranty is valid, the notebook should be repaired free of charge.

Greets

5 more replies
Answer Match 82.32%

i upgraded to windows 10, and surprise surprise my touch screen is gone.   no drivers, no hint of it anywhere on my pc settings,  i tried finding a link on HP's website to redownload the software, no such luck, you would think for such a common problem hp and microsoft would get there act together and provide a patch.  Any ideas anyone. thanks

More replies
Answer Match 82.32%

I bought a windows 8 hp pavilion touchsmart and touch screen worked. I updated to Windows 10 and it worked, only after I did a factory restore did it not work. I've tried everything with the device driver and another factory restore and it still does not work. I sent my computer in to get it fixed while it was under warranty and it was still not fixed. I resigned to it not working and I think that hp should have solved this problem before selling its computers. So we are blaming it on Microsoft 10, but that is not the issue when it worked until I did a factory restore and attempted everything suggested. I have a 350 dollar piece of **bleep**. Plus now my Mic isn't working and there aren't any drivers for me to upgrade to, anywhere.

More replies
Answer Match 82.32%

Screen was cracked so I replaced the screen. Now touch doesn't work.
There is no "Pen and Touch" and "Tablet PC Settings" in Control Panel. In PC info it says, "No pen or touch input is available for this display."
Touch DOES work on LINUX as I ran it from a usb drive, so it is not a hardware problem.
I have reinstalled Windows.
I have another Yoga 2 Pro and comparing Device Manager in both I see no differences.
How can I get the touch to work again?

A:Why doesn't my Touch work after replacing the screen on my Yoga 2 Pro?

try refreshing your PC maybe the driver is not working properly
If the touchscreen does show up on the device manager try updating the driver from there. (it will be listed under HID )
​Otherwise To refresh your PC Swipe in from the right edge of the screen, tap Settings, and then tap Change PC settings.
(If you're using a mouse, point to the upper-right corner of the screen, move the mouse pointer down, click Settings, and then click Change PC settings.)Tap or click Update and recovery, and then tap or click Recovery.Under Refresh your PC without affecting your files, tap or click Get started.Follow the instructions on the screen.

3 more replies
Answer Match 81.06%

This morning i turned on my U920T-10J but the screen stayed black.

At first I thought the screen was broken but in "tablet mode" the screen went on. Now when i want to slide out the keyboard the screen goes black again.

How can this problem be solved?

A:Satellite U920T - screen turns black when sliding out the keyboard

Hi

For me it looks like a loose connection somewhere between the display and the motherboard.
This might be possible reason for display blackouts while sliding in and out.

I guess this cannot be solved easily and I think this is a job for an technician (authorized service provider). I recommend you to contact the service technician in your country to get the notebook fixed. Hopefully the warranty is still valid in order to fix it free of charge.

I hope this can be fixed?. I keep finger crossed.

3 more replies
Answer Match 78.54%

Recently there has been an issue with my Z930 and I'm not sure if it's a damaged screen or if it's something to do with the software. I'm also using Windows 8 as the operating system.

Earlier today the device was running as normal, but it later began flickering with a mess of pixels everywhere like a glitch, with black lines rising from the bottom of the screen.

A few seconds after that cleared up, the entire screen turned black.
It is still lit up, but there's only a blank, black screen - I can't even see the cursor.

Every now and then the screen flickers like it's struggling to keep working. I hooked it up to another screen and its typical display showed on the other device, so I'm taking a guess that it's a damaged screen.

Before I start preparing to get a new screen or even a new device, is it possible that it might be something else other than a broken screen?

Because it's odd seeing that I take great care about the screen because it is fragile to begin with, I haven't knocked it or had any fluids on the screen, so having it suddenly break like that is pretty odd.

A:Satellite Z930 doesn't work - black screen

Hi

The described symptoms like flickering with a mess of pixels sounds like a graphic card problem.
Also the fact that the same symptoms are visible on the 2nd external screen, would confirm my assumption that the GPU would be affected.

In case the internal screen would be faulty, the external screen should work properly but this isn?t the case.

From my point of few the motherboard together with the GPU has to be replaced in order to fox the issue but of course the whole notebook should be tested by an service engineer before starting to replace any parts.

3 more replies
Answer Match 77.7%

Lately, when I use "Alt + left arrow" or the back setting on my logitech MX revolution mouse, firefox doesn't seem to recognize my keystroke/click.

Instead, I have to click the blue back button on the top left of my screen.

What course of action do you suggest I do to correct this? Thanks in advance,

-Cardinal
 

A:Firefox "Back button" doesn't work

Firefox Keyboard Shortcuts
 

3 more replies
Answer Match 76.86%

Hi! I'm at the end of my rope trying to solve this issue with the mouse/touch pad on my Toshiba Satellite running Windows 8.1
 
The mouse pointer doesn't work in the center portion of the screen. The mouse pointer doesn't disappear or anything; but if I try to click on something in the affected area nothing happens and I can't complete any tasks. If I'm able to move the item to an area of the screen where the mouse pointer does work (for example, minimizing my browser), then I can open up the item that I was previously unable to work with. This only happens in a section on the center of the screen and it happens with every single program, not just my web browser. So it's clearly an issue with using the mouse in this area of the screen; I just don't know what's causing it and how to resolve things. Oh, and I also can't alternatively use the touch screen to access things in this area of the screen either. It's like there's an entire area blocked off from accessing.
 
The mouse shows as working properly in Device Manager. Ideas on what to do or what could be causing this to happen?

A:Mouse doesn't work in center portion of screen on Toshiba Satellite - Help!

It almost sounds like something is running in the background that would be in that center space, not allowing selection or operation.

0 more replies
Answer Match 73.5%

I have pulled it a part and cleand it but I wont work no matter what I have done can u plz help by the way it is a luminer 532 Microsoft

More replies
Answer Match 72.66%

The usefulness of the back shortcut click on my mouse is compromised by all this clutter. Is there a way to work around this? I never know how many times to hit the back button.

A:Back button doesn't go back (sort of)

I think you came across a redirect page. When you go to certain pages you are redirected to other pages. When you click the "go back" button you go back to the redirect page, which sends you to another page. And than you get stuck. In those situations just use the drop down menu (like you have on your screenshot) and go to the page before the redirect one, in that case it would be the volume out vista something one.


Whenever your "go back" button doesn't work, just use the dropdown menu to jump the redirect page.

2 more replies
Answer Match 71.82%

Hey guys,

(1) Just put together a new computer with Win7 and ASUS M2N68-AM SE2 motherboard
(2) USB ports in the back work fine (iPod, iPad, etc.), but the ones in the front don't work
(3) When plugging in a device in the front USB, it says "Installing Device..." and then "Device couldn't be properly installed"
(4) But strangely a USB flash drive works fine in the front USB
(5) Also, USB hubs don't work. They act just like my front USB ports.

This is so bizarre but it's actually causing me some problems because I recently broke an arm and cannot reach the back of the computer to plug in an USB device.

Would greatly appreciate your help guys!

Thanks,
Josh
 

A:USB ports in Front don't work, but the ones in the back do?!

Do you have all Win 7 updates installed? Recent ones included USB drivers.

Are the board connectors backward?
 

2 more replies
Answer Match 70.98%

Sound trouble
front PDIF out header does not work when i plug out the back speakers.
It IS working when i plug in back.....
but not the mic jack in the front..
all back is working fine....
Been updating drivers, looking through systems
got Via HD audio deck innstalled...

any help here? :-)

More replies
Answer Match 70.98%

Setting up 10 school computers in one classroom--all the same. Mike won't record through the jack in back of the computer (Pink) but works fine in the pink jack in front. Is there any correction so that all wires can be plugged into the back of the computer?
 

A:mike won't work in back jack, ok in front???

IT is possible that with the ports working on the front of the computer, the audio porst on the back have been disabled so the front ports will work. THis usually requires the jumpers for the sound ports be put back to the way the factory set them.
 

3 more replies
Answer Match 70.98%

i recently put together a new computer and i am having trouble with the audio panels and the audio its self, from either aux cords, headphones and optical audio cables nothing is working. i know the headphones work because i use them when plugged into the monitor its self the mother board wiring is all correct into the hd audio slot and so forth. if anyone can help me please and thankyou

A:Audio from the front and back panels don't work...

Hi, do you still need help with your audio problem?

1 more replies
Answer Match 70.56%

Hello,I am desperate for help. My laptop will turn on. And I can type in my password. But then when the computer loads it takes a very long time and when it gets to the desktop the keyboard, the mouse, the touchpad, and the touch screen won't work. I can see everything on my desktop. But I cannot open anything or do anything at all. How can I fix this?Thank you!!!

More replies
Answer Match 70.56%

Hello,
I just upgraded from windows XP to Windoes 7 & installed all the latest available motherboard drivers from intel.
Everything is working fine but there is no audio via my front audio jack. Even Realteck Audio Manager is even not recognizing any pluggen in jack in the front audio panel.

Have installed the latest drivers & checked the Realteck Sound Manager settings. There everything is OK but don't know whats wrong.

Will be thankful if any of you genius people give the solution.

Configuration: - Intel P4 C2D Processor
Intel DG33FB Motherboard

Regards,
Bekar

A:Front Audio Doesn't work - Windows 7

Use the Windows Update drivers. Don't use the ones from your CD

7 more replies
Answer Match 70.56%

Hello Forum Members,

I have a Creative Audigy 2ZS Platinum sound card and Front end Drive installed on my PC. Although everything is correctly installed with all the proper cables, I can't get any sound from the headphones when they're plugged into the 1/4" phone jack. Neither can I get anything to record using the front end MIC jack. I'm using a Radio Shack PZM microphone. since it uses a AA battery, I'm assuming that the microphone is of the "dynamic" type.
The Jumper is in place on the front end driver board. All drivers and features are current so, there's no problem with upgrades. Can anyone give me an idea of what's wrong? I've tried the Creative Labs website and got better information from my dog :hotbounce :hotbounce
 

A:Audigy 2ZS Platinum Front end doesn't work

On your lower right handed corner, you should see a speaker icon, right click on that and click on properties. Make sure the Master volume control isn't mute-do not check the mute box.
 

1 more replies
Answer Match 70.56%

Hi everyone..
I'm having a problem with my sound setup. I'm using Windows 8.
I have a 2.1 channel speaker, headphone and microphone.
On rear, I've connected my 2.1 channel speakers and on the front jack, I connect my headphones and microphone.
The headphone works fine but Windows won't detect the microphone.
But when I connect the microphone in rear jack, it works fine.
The problem is that I have a combined Microphone and Headphone system. Either I plug them both on rear or on front. I want to plug them at the front jack because at the rear jack, the headphones won't sound well in line it jack(the blue one). It used to work fine in Windows 7 but the front panel won't work in windows 8. please help me as this is screwing me off.
I use BIOSTAR G31M Motherboard with VIA HD Audio.
G31M :: Motherboard :: BIOSTAR

A:Front Panel Mic jack doesn't work

Check the connector from the Front Panel to he motherboard (with the PC powered off, reseat (unplug then plug back in) the connector. There could also be a problem with the front panel headphone jack.

Since this is apparently a custom built system, check the connection from the front panel. Many cases have both a HD Audio and an AC97 audio connector. If you have an HD Audio connector, that is the preferred connector.

16 more replies
Answer Match 70.56%

Hi I have just built a computer and the case needs AC 97 audio. The mother board is set to Digital I think. I cant find the option to change this any where in my bios. I have a Gigabyte M61PME-S2.

Any Help on fiixing this would be great
 

A:Front Audio Port Doesn't Work

Some MB boards u hav to set the jumpers differently to route the
audio to the front ports. Did u chk ur MB manual for this to see ?
 

2 more replies
Answer Match 70.14%

Yesterday everything was fine. Today I woke up and I had this issue.

The headset I use comes with 2 3.5mm cables that need to be put into both the audio output jack and the microphone input jack. The audio output works fine, however, the microphone input jack does not pick up my voice or anything.

These are my volume settings:

Everything looks fine there and everything is plugged in fine. I have the latest RealTek drivers installed and my motherboard is the ASUS Z97-K. I checked the BIOS settings and everything seemed fine, it was set on HD audio and was the same before this issue randomly occurred.

Would really like help solving this as it is so frustrating not being able to use my mic. Also, I have tested the mic on other computers and it works fine so clearly something is wrong either with the hardware or software on my PC. Also, this PC is quite new maybe a month so far. Also, I have windows 8.1 64 bit installed.

Thank you in advance.

A:Microphone inputs do not work on back or front panel

Did you do the "Refresh" as I suggested on the Win 7 forum?

25 more replies
Answer Match 70.14%

Yesterday everything was fine. Today I woke up and I had this issue.

The headset I use comes with 2 3.5mm cables that need to be put into both the audio output jack and the microphone input jack. The audio output works fine, however, the microphone input jack does not pick up my voice or anything.

These are my volume settings:

- Recording Tab
- Playback Tab

Everything looks fine there and everything is plugged in fine. I have the latest RealTek drivers installed and my motherboard is the ASUS Z97-K. I checked the BIOS settings and everything seemed fine, it was set on HD audio and was the same before this issue randomly occurred.

Would really like help solving this as it is so frustrating not being able to use my mic. Also, I have tested the mic on other computers and it works fine so clearly something is wrong either with the hardware or software on my PC. Also, this PC is quite new maybe a month so far. Also, I have windows 8.1 64 bit installed.

Thank you in advance.

A:Microphone inputs do not work on back or front panel

Either a System Restore back to when it was working or a Refresh of the Realtek will probably take care of it.

To "Refresh" the sound, go to the Device Manager, RIGHT click on the entry for the Realtek sound. Then LEFT click "Uninstall". DO NO uninstall the drivers. Restart the PC and when Windows starts it will detect and reinstall the sound.

We have a separate forum for Windows 8/8.1.
Windows 8 Forums

Also, how to post screenshots on this and the Windows 8 forums.
Screenshots and Files - Upload and Post in Seven Forums

3 more replies
Answer Match 69.72%

I am frustrated! I need help. I don't know much about computers but, I am willing to learn. I have windows XP
The microphone and line in plugs work if I plug in my headset in the back of the computer. But the headset doesn't work when plugged into the front panel.
I would like to have the headset work when I plug it in the front panel. I am working with a vocie activated word processing program that is fantastic. But the headset cords are a little too short to be comfortable when it is plugged in the back of the computer.
Any suggestions? I would appreciate any thoughts or ideas.

Thank you- shauna
 

A:Front Panel Microphone plug doesn't work

16 more replies
Answer Match 69.72%

ok real simple - or it should be - my back button doesn't go back a page, ie does, but want out of that mess, the button is not greyed out. any ideas??
 

A:firefox back button doesn't

What version of Firefox are you using? I am using v. 1.0 Preview Release and have no such problem. Maybe you need to uninstall and reinstall?
 

1 more replies
Answer Match 69.72%

Touch pad doesn't work if you close and open the laptop, sometimes the touch pad turns off on it's own. I have checked the settings for the touch pad and for what the computer does when closing the lid, they are correct. Tried booting in safe mode and still had same results. The only way to get the touch pad to come back on is if you reboot the computer. Any ideas?

More replies
Answer Match 69.3%

Hi guys,

my girlfriend ordered a Toshiba Satellite U920T-100 about three months ago, and she has had problems with it since. We are not quite sure what causes them, because they seem to happen at random.

The issues are:
- It starts, but freezes at the Win8 Login with a blue screen (a rather warm blue, not the blue screen of death)
- It won't start at all, only after few attempts
- It won't shutdown
- It freezes while organizing files (e.g. copying files from A to B, but not even large amounts of files)

Again: those issues seem to be appearing completely at random, I wasn't able to reproduce them in any way.

Additionally: the WLAN connectivity is really bad.
The laptop isn't able to find networks, while my laptop has no problems with it.
And when it does find them and connects, the connection gets lost - again: no clue why.

This surprises me the most, because in the tests and reviews I've read the connectivity got praises everywhere.

Should I factory reset it?
Run through some specific tests?
Or is is hopeless, because there're so many issues with it?

I would appreciate your help!

A:Some issues with Satellite U920T-100

Hi

>Should I factory reset it?

I think you should do that because the described issue can be related to system problems as well as hardware issue (i.e HDD). The factory recovery helps you to check if its software or hardware related problem.

Usually all software (system) problems could be solved by recovery process. Hardware problems would continue.

So from my point of view, system recovery is the first step you should try to perform in order to solve the issue.
In case this does not help, an hardware issue (HDD or RAM) can be possible and since the notebook is still covered by warranty, I would recommend you to contact the service in order to check the unit.

Hope my advice could help you a little bit

1 more replies
Answer Match 68.88%

I'm looking at PC for a friend. The power supply was obviously dead so I grabbed another one, matching the wattage. When I plug power into the PSU and turn on the switch on the PSU the computer boots. I try to turn it off with the power button on the front bezel but it has no effect.
Figuring it might be a problem with that PSU I tried another one, but with the same effect. Any suggestions would be helpful!

Kevin
 

A:Solved: Changed PSU, front power switch doesn't work?

Since it's not the P/S, it's either the MB or the power switch. Disconnect the power switch from the MB connection, then plug the system in. It should NOT power up by itself, unless the BIOS is configured that way. In any case, short the two pins for the power switch briefly, and it should act just like you pressed the power switch. If so, the switch and/or wire is bad. Otherwise, it's probably the MB that has the problem.
 

3 more replies
Answer Match 68.88%

hi,

the letters R and G don't work anymore. What can I do about this?
Thanks

More replies
Answer Match 68.88%

So recently my laptop Pavilion DV6xxx updated the OS to Windows 10 64 bit and for some reason the touch pad works, but the scrolling system i.e. the designated scroll bar partition doesn't scroll any more. I have the Synaptics Pointing device software and my system is up to date in drivers yet it doesn't work. Please help as not being able to scroll with the touch pad is a huge inconvenience.

More replies
Answer Match 68.88%

hi recently my laptop has had a problem concerning a update from microsoft and has been restored to an earlier point before the update. Now my touch pad won't work so i got to connect a mouse every time i want to use it is there any reason it won't work concerning drivers or is my touch pad broken...

Thanks in advance
Xeno
P.s. its a sony vaio with vista installed intel dual core 1.67ghz
2Gb ram
120gb of hard drive space
im ussually good at fixing this kind of stuff but its my first time using vista
 

A:Laptop doesn't work with the touch pad

Did you reinstall the drivers/software?
 

1 more replies
Answer Match 68.88%

Hello! I've just installed Windows 7 Professional on my HP 350 G1.  I have a problem with touch pad - it works, but just as mouse (and also installed as mouse). I've tried to update and downloaded synaptics driver, but it failed to be installed. I can't delete previous version of Synaptic driver and installed a new one, because it's not in Programmes list at all.  Windows Update doesn't work as weel, if it's relevant.

A:Synaptics touch pad doesn't work

 Hi, Install the driver from the device manufacturerhttp://drivers.synaptics.com/Synaptics_v17_0_19_C_XP32_Vista32_Win7-32_XP64_Vista64_Win7-64_Acme_Inc...

2 more replies
Answer Match 68.46%

I have a fresh system with Win 8.1 64bit ??but in the course of my installations leads something to this problem.
I never had this trouble.

Who can help me?
Every time I have to renew system but it does not help.

greeting markus

A:Satellite U920t . Win 8.1 64bit swiches from dpc

Sorry matte but could you provide more details to your issue and could you describe this problem in detail

Your post is not very helpful and more details would be required.

3 more replies
Answer Match 68.46%

Hi,

My display settings say: generic pnp monitor with a driver date of 2006. Updating the display settings does not change this.
What is the proper display driver for this laptop and how can i change it?

A:Old display driver for Satellite U920T-10J

Proper display driver you can find on Toshiba download page - http://www.toshiba.eu/innovation/download_drivers_bios.jsp
There you can find last and tested drivers.
All drives offered there are part of original recovery image when you get notebook with preinstalled operating system.

2 more replies
Answer Match 68.46%

Hello together,

i have been using nice nice device now since a few weeks and starting to get troubles with it.

I have the problem that randomly the touchscreen get without any function, i can touch the screen
however i want but without any reaction.

It just starts without starting any applications or anything before, i just browsing in the web and from one second to another.

If i restart the PC, everything is working normal again, i still using the drivers that were pre-installed and did not any changes to the Drivers so far.

Any suggestions what could cause this issue ?

Kind Regards

A:Satellite U920T-10G - touchscreen without any function

Hi

In my opinion an process which controls the touchscreen hangs or does not response anymore and therefore you cannot get the touchscreen function to work.

Would recommend to reinstall the +Toshiba System Driver+ from Toshiba EU driver page.
If this does not help try the system recovery and test the unit with factory settings.

9 more replies
Answer Match 68.46%

Has anyone upgraded a Toshiba U920T to Windows 10?

I only ask because that model is not listed in the Toshiba Tempro list of models that can be upgraded. So am I stuck with Windows 8.1?

My part no is PSUL1E-00D00JEN; SER No:: ZC128613H

A:No Windows 10 support for Satellite U920T?

According to this Toshiba page: “models supported for upgrade to Windows 10”, the Satellite U920T will not get Win 10 drivers.

http://win10upgrade.toshiba.com/swup...spx?region=TEG

Models not listed do not support an upgrade to Windows 10.

3 more replies
Answer Match 68.04%

Hey there,

I'm using the onboard sound of my ASUS P7P55D motherboard.
The back audio connectors work fine, but I somehow can't use the front panel that I connected to the mobo (yellow cable).

Is there a trick or any setting to activate it with win7 professional x64?

I also tried changing to AC97 in BIOS, didn't help...

thx!

A:Front audio Panel doesn't work (ASUS P7P55D motherboard)

Check which it is that the csae has as they are wired differently between HD Audio and AC97,

It is also possible that that fpaudio block is wired wrong and neither will work. If that is what it is it will take pulling and reseating the various wires in the block; not easy but can be done.

9 more replies
Answer Match 68.04%

In Windows 7 there is a feature whereby when you combine the Windows button and the Tab button it will spool through open programmes in an "apple" kind of way.

I used to be able to do this with my old laptop running windows 7 but cannot with my lovely new Toshiba, why?

A:Satellite Pro R850-143 Windows + Tab button does not work

You need Aero (3D interface) enabled for that feature, which requires the correct Graphics Driver. Do you have the pre-installed factory Windows installed?

1 more replies
Answer Match 68.04%

Hello everybody.

I got an ASUS N50Vn aka X5AVseries..

On the top of the keyboard I got a "touch panel" where I can control the volume, change the computers performance and so on.

But after installing Windows 7 it doesn't work.

Anybody knows what to do? Maybe a speciel driver I need?

Thanks, Peter.

A:ASUS - Touch Panel doesn't work?

You have to install all the acpi/she drivers from asus's website. You can use the vista or xp drivers.

(had to do this on an 1000he from asus, but I got almost all hardware keys working)

9 more replies
Answer Match 68.04%

Hi, Please help! I updated to window 10 this evening and things seemed fine. I dowloaded a few apps and restarted the system. Whe the system came back - the cursor wouldn't leave the top of the screen - just flickering aroung the top edge. The keypad works, as do the left and right clicks and the pointing device, but I fing he pointing device imposible to use and as soon as either the touchpad is toched, or the pointing device is touched at the same time as the left and right clicks - the cursor goes straight back to the top of the screen (where the close button is) As I am sure you can understand - this is all but unworkable. I have looked to se if the driver needs updating - it doesn't. Can you help? Richard











Solved!
View Solution.

A:Updated to Windows 10, now touch pad doesn't work

I manually reinstalled a windows 7 software for synaptics (none later available) and is currently working. Will keep my fingers crossed.Thanks for your help

10 more replies
Answer Match 67.62%

Windows XP suddenly the screen was upside down and back to front.
Is there a way to correct this?
 

A:Screen upside down and back-to- front

8 more replies
Answer Match 67.62%

Error BSOD Toshiba U920T card reader and Windows 8.1

Whenever I do a Scan, Format, Copy or Delete operation on my internal SDCARD I receive this error.
KMODE_EXCEPTION_NOT_HANDLED or FAT_FILE_SYSTEM,

I have tested everything, all drivers are updated and it happens even with laptop in safe mode.

I even experimented with SDCARD formatted with Fat32, exFat and with NTFS.

This happens with the internal reader, if I use an external SDCARD reader connected to USB, there isn?t any problem, so there is no physical problem with cards.

I use 2 SD, one with 128GB and the other with 32GB.

If 32GB inserted, I do a disk>properties>scan and comes the BSOD saying FAT_FILE_SYSTEM without number

If 128GB inserted, I do a scan and comes the BSOD saying KMODE_EXCEPTION_NOT_HANDLED no number

Anyone has any idea or my internal card reader needs to go guarantee?

A:Satellite U920T - SD card reader error

It looks like the internal SD card reader does not handle the inserted cards properly.
According to the notebook specifications (user manual) the card reader supports the SD card, SDHC and SDXC cards.

The card reader supports
SD cards up to 8GB
SDHC card (4GB/8GB/16GB/32GB)
SDXC card up to 64GB

3 more replies
Answer Match 67.62%

Since 2 weeks my microfone dont work in skype.
Also my touchscreen dont working.

How to pepair?

A:Satellite U920T-10J: microphone and touchscreen not working

Regarding the touchscreen issue:
Does it happen while the screen is pushed up?

I read about the similar issue in different thread and this problem could be related to lose connection.

But check firstly this workaround:
1. Window+run
2 .type services.msc
3. go to Human interface device access
4. right click --->property---->start up type----->automatic (delay start)

But if this will not work, the issue could be caused due to hardware malfunction and such kind of issues must be fixed by authorized service provider.

Regarding the internal mic issue:
Please check if internal mic appears in control panel – sound – recording device
Check also whether all recording device are enabled. Click right and ensure that both options “show disabled devices” / “show hidden devices” were marked.

Also the Skype sound settings should be checked. The internal mic should be chosen as default mic.

1 more replies
Answer Match 67.62%

Any one knows if there is a service manual for this model or schematic of inside this computer with the back cover off .

thanks

A:Satellite U920T-11C: How to insert additional RAM modules?

The Satellite U920T memory is not user upgradable. This means that if you would like to upgrade the memory, you should contact a Toshiba authorized service provider for assistance.
In case you would try to disassemble the notebook by youself, you would lose the warranty validity.

But from my knowledge the Satellite U920T series supports only ONE memory slot and only one memory module (max 8GB RAM) can be installed. So even if you would like to upgrade the memory, you are limited to 8GB RAM.

4 more replies
Answer Match 67.62%

I have a U920T, using only the touchpad, combined with the touchscreen.
But the touchpad got dirty, with some dust inside.

It is quite annoying on a daily use.
I could not clean it with a vacuum cleaner, nor by blowing air with a bike pump.

Does somebody knows a way to remove dust from within the touchpad?

Thank you
LT

A:How to remove dust within the touchpad on Satellite U920T

I use some adhesive strips in order to remove the dust between the touchpad and touchpad buttons.

3 more replies
Answer Match 67.62%

Hi,

I just purchased the U920T-11C a few days ago.
I like it but there a few issues they are putting me off and make me want to return it.

The first issue is the loud fan noise that comes on. Is there anyway to turn this off?

It happens about 15 mins into using the web and then goes on and off every 5 mins or so. It is really loud and being in quiet room it is noticeable.

Is there anything I can do to stop this? I am only using the web and not running any other programs.

Also I have noticed the touchscreen fails to respond for no particular reason. I don't know if there is a pattern but it is frustrating when it just stops for no reason and then sometimes just works again.

Looking at these forums it seems like it is a common problem with the Toshiba. I have a few days before I can return so if these are not solved I think I might just go form the Samsun ATIV Book 9 Lite instead.

Thanks

A:Satellite U920T-11C fan noise and touchscreen fails sometimes

> It happens about 15 mins into using the web and then goes on and off every 5 mins or so. It is really loud and being in quiet room it is noticeable.

I assume the noise is coming from the fans which need to run faster in case the internal temperature would increase.
What you could do is to change the cooling module performance in single power plan.
You could also decrease the CPU performance. This would lead to smaller heat dissipation and the fans would slow down.

> Also I have noticed the touchscreen fails to respond for no particular reason. I don't know if there is a pattern but it is frustrating when it just stops for no reason and then sometimes just works again

You could try to calibrate the digitizer
Go to control panel (Windows key + X -> control panel) -> ?Tablet PC setting?.

The first tab ?Display? contains options like ?Configure the pen and touch display?.
Here you should be able to start Setup and to identify the touch screen.

The first option should contain ?1 internal LCD?
At the bottom you could find button to calibrate and reset the settings for this internal LCD.

But it could be also an hardware malfunction. I cannot say for sure why this happens but maybe an technician should take a look on the hardware.

4 more replies
Answer Match 67.62%

Hello,

I have a new U920t-102 which I am very happy with, but I have this issue with the mousepad's right click (meaning the 'button' the user is able to press on the bottom-right side of the mousepad): sometimes it actually works as a right click, sometimes it works as a left click.
This is annoying especially during web navigation: I'm used to right click on links and open them in a new tab, but when the right click acts as left, I loose the current web page.

I tried to figure out what this behaviour depends on, looking at the animated synaptic icon in windows' tray bar while playing with the left and right click; if I continuosly press the right click button on the mousepad, after some repetitions it will consistely and correctly work as right click, but if press the left click once or more than once, the right click button works as left click for some pressures, and then 'corrects' itself and start again to work correctly.

Any idea/suggestion? is it a hardware problem?

Marco

A:Satellite U920t-102 touchpad right click issue

Usually the touchpad right / left click can be configured in the Synaptics settings.
Right click on Synaptics icon in tray and point to devices properties.
In buttons tab you will be able to choose right handed scheme or left handed.
Here you could choose the scheme appropriate for you.

You can also try to uninstall the Synaptics touchpad driver and could test the touchpad functionality without the usage of additional touchpad software.

But if this doesn’t help, your might have hardware problem

1 more replies
Answer Match 67.62%

I have a really frustrating problem...
My front panel/jacks won't work..
I tried installing realtek audio drivers..
But no audio manager..
I downloaded the drivers from realtek website
Others say it is already packed in with the codecs..
I mean the audio manager is already packed with the codecs.
There's no icon on the taskbar
and no realtek control thingy in the control panel
My headset and my mic doesn't work on the front panel
The rear panel is fine
But I want my front jacks
Tried searching on the webs.. But couldn't find any audio manager
I installed the drivers and restarted over and over..
Still nothing.. Mind helping me out?
Please... I really need assistance..

I have ASRock G31M-S for my motherboard
Intel Core 2 Duo
Nvidia GeForce 9500
Memory is 4GB

I'm really pissed... But I'll check out the BIOS

A:Windows 7 Home Premium 32xbit front jacks/panels doesn't work

This is probably a silly question but have you checked to be sure those front panel jacks are connected correctly?

6 more replies
Answer Match 67.62%

Is there a way to make IE8 automatically refresh web pages when pressing the back button. I can't seem to make IE8 do this, even though in IE8 > Tools > Internet Options > Browsing History > Settings, I have "check for newer versions of stored web pages" set to "automatically"

Anyone else have this problem?

A:In Vista, IE8 doesn't refresh web pages automatically when back button is hit

Hi badweather,

If set to Automatically, it will not refresh a previously visited page from the Back-function. As it's set to store the information that you've recently viewed. You need to set it up as below if you want to use this: (Note that this does indeed make the browser check for a new version every time, on a slow internet connection, this will cause extra loadtime)

19 more replies
Answer Match 67.2%

Hi everybody,

just a quick question, I read on the internet and where I bought my laptop that the Satellite Pro U500-1D5 has a touchscreen.
Now when I want to install this, it is not possible because this function is not available?

Can someone confirm this or tell me if I am wrong?

Greetings

lessius

A:Has Satellite Pro U500-1D5 touch screen or not?

I found notebook specification on Toshiba page HERE but I cannot find this info. Obviously this notebook model is without touch screen.

Have you found some info in User?s manuals?

3 more replies
Answer Match 67.2%

Yesterday I reinstalled Windows 7 on my notebook PC. I had to use a Microsoft installation disk because unfortunately, serious errors resulted after I installed from the HP recovery program. Consequently the HP drivers that were installed automatically with the recovery program weren't installed on my system. I had to install several of them from the HP support site. I got everything to work except for the Touch volume control, or the Volume Scroll Zone as referred to by HP in the service guide. This is the device located just above the keyboard that increases or decreases speaker volume when you drag you finger on it. I installed the Quick Launch button driver but that only applied to the mouse and pointer touchpad. I looked at the devices listed in my startup configuration. I saw the synaptics pointing device and the HP quick launch buttons listed. So is the IDT PC audio driver.  What am I missing? Where I can I find it to activate the touch volume control?

A:Touch volume control doesn't work on dv6, looking for driver

@accordeoniste Try these. http://ftp.hp.com/pub/softpaq/sp48001-48500/sp48425.exe http://ftp.hp.com/pub/softpaq/sp46501-47000/sp46731.exe REO

2 more replies
Answer Match 67.2%

I am on a Toshiba laptop. My (numeric) four button doesn't work, when I push it nothing happens onscreen. Is there anything I can do to fix it.

More replies
Answer Match 67.2%

I open up the Laptop and the screen is blank with the power button blinking. I press the power button but it continues to blink and the screen stays dead. Help!

More replies
Answer Match 66.78%

Hello

i have following Problem with my U920T. The sound with the built-in speakers is perfekt, but if i use headphones the sound gets very quiet nearly unhearable.
I tested several headphones und different settings of the software. I also tried installing all Windowsupdates and the driver updates incl BIOS from the Toshiba homepage nad drivers from realtek.
Now i reinstalled Windows but the problem still exists.
I still thinks is a driver problem but have no idea what to do now.

I hope for fast help

regards 7even

A:Satellite U920T - sound with headphones quiet and distorted

That?s really strange but I think there is problem with some wrong settings.
I don't know how do you test your headphones but make some test with browser player.
Open Internet Explorer and open this test page. Start for instance my favourite In the Mix radio and when music runs click with left mouse button on speaker icon and open option Mixer.
Your IE will be listed there. You can move volume level for speakers but for IE too.
Set both of them on the 50% and check if the problem persists.

I use headphones pretty often but I?ve never noticed such problem.
Please test it and send some feedback.

5 more replies
Answer Match 66.78%

Hi Folks,

is there some one who has WIDI working? AFAIC there was a WIDI Symbol in Device Manager @W7, after upgrading to W8.1 there is no way to get it work.

Trying to use Intel Display Driver fails because customized toshiba Driver, the latest Toshiba Driver is dated with 28.10.2013 that should be an early W8.1 Driver if not W7.

Is this something like the Broadcom GNSS Feature? Build in but still not usable?

A:Satellite U920T-100 PSUL1E - WIDI is not working after Win 8.1 upgrade

Hi

According to Toshiba information which I found in the technical support bulletin document, the Intel Wireless Display is no longer supported on Windows 8.1, but you may be able to connect to external display wirelessly, if your computer supports Miracast?.

Here the link to the doc:

Important notice for users of Wireless Display (WiDi)
http://aps2.toshiba-tro.de/kb0/TSB3903IF0000R01.htm

By the way: the Intel display driver can be installed and updated but you have to do that within the device manager. You have to download an zip package containing single driver files and then you could update the driver using the advanced procedure within the device manager which allows you to choose the driver folder containing the single files.

3 more replies
Answer Match 66.78%

Hello, Good morning/ evening ...
I'm using ( Satellite U920T) and recently upgraded my tablet to Windows 10
but after that, the function keys, volume, brightness, FN key, and even the backlight doesn't work anymore !!

I have tried to recover the system and to update driver's software but nothing worked ..

I use these keys all the time and now it's really hard without them !!

What's the problem? what should I do?

A:Satellite U920T - Function keys not working after update to Win 10

The problem is that Satellite U920T isn’t listed as Win 10 supported unit and therefore the Win 10 Toshiba drivers and software which controls the FN keys isn’t released.
But as far as I know to use the FN keys, the Toshiba System driver as well as Flash Card Support Utility must be installed.

For all Toshiba Win 10 supported units, the drivers can be downloaded from this page:
http://win10upgrade.toshiba.com/swup...spx?region=TEG

Maybe you could try the drivers released for other Win 10 supported notebook models…
I’m not quite sure if the software will be fully compatible with your U920T model but its definitely worth a try…

1 more replies
Answer Match 66.78%

Hi Forum,

I am new here and am having a problem I can't solve by my own, so am asking for help.
I am using a Toschiba Satellite U920T-100 since more than a year.

Since around 1 week, once I slide up the display to have access to keyboard, the touchscreen does not work anymore. Once folded (keyboard hidden) touchscreen works.
I downloaded most of the drivers, re-istalled, even did a "set back" to cancel last Windows Update... etc.

Trying to modify touchscreen settings under control panel, I receive a message "touch- and pen settings are not available. contact pc-manufacturer (error = 0)"

Does anybody have an idea what to do?

Ane more, but might not be connected to the problem above: Under device manager, "INTEL WiUSB" entry shows a yellow exclamation mark.

Would be great if someone could help. Thanks!

Cheers
Andreas

A:Satellite U920T - Touchscreen disabled when display is slided out

Hi,

I have exactly the opposite problem, my touchscreen is disabled when the keyboard is slided in and enabled when slided out.

I have contacted Toshiba support, but the only answer they have is to reset Windows!

Thank you for any actual solution.
Lo?c

12 more replies
Answer Match 66.78%

I have a Satellite U920t.

When I powered up this morning, Windows displayed a message "Keep your PC on until this is done. Installing update I of 5...".

This status stayed on for ages, in fact, I left it on for hours hoping that it was a large update file, I even went out shopping and when I got back home, it was still displaying the same.

I tried pressing ALT-DEL, but nothing happened. I then powered the PC down, left it for a few minutes and powered it back up, but the PC just came straight back up with the same update message!!!

I also noticed that after the PC was supposedly powered off, the system drive LED would blink on and off intermittently as though it is actually still running or locked.

Bearing in mind that this PC uses solid state SSD drive, and I have no way to remove power from the unit completely, I suppose that I am actually not turning the process off.

Can anyone tell me how I can get this PC out of this loop and get my PC back working again please?

I tried looking up the web on another PC, but all the information seems all over the place.

I presume that this is really a Microsoft issue, but I would really love to know how to get back into my PC again.

Regards
Tony

A:Satellite U920t: Win update - Unable to reboot even when power off/on

Hi

Did you try to press and hold the power button 4 seconds long?
Usually this should interrupt the loop process.

Try also this:
Power up the unit and press F12 button. Now you should see an boot menu where you could choose certain devices. Last option should be HDD recovery.

Chosing this HDD Recovery option would allow you to reset the system back to the factory settings.
Check it out!

3 more replies
Answer Match 66.78%

i need to do forwarding and backwarding in video play . but Window Media PLayer 11 doesn't enable back/forward button ?
 

A:why Window Media PLayer doesn't enable back/forward button ?

There's a button on my keyboard that does this. What type of keyword do you have?
 

3 more replies
Answer Match 66.78%

Ever see this? You search google, click on a result, and then either backspace or click the back button, but instead of going back to google, you stay on the current site. Why does that happen, and is there anything to do about it?

Using IE 8 32-bit in W7 64-bit here, but have been seeing this problem for a long time with previous versions.
Any ideas?

Thanks!

A:With some sites, clicking back button doesn't bring you to prev. page

I thought I was going crazy with that too. Check for malware, spyware and adware....could be the culprit.

4 more replies
Answer Match 66.78%

Hello,

I am using a Satellite Pro S500-139 and am having problems with my F9 key. When i type my palm touches the mouse and send the cursor somewhere else on the page. I have reinstalled the ALPS pointing device and now have access to the advanced setting that i wasn't able to get.

Although i can adjust the sensitivity etc i would really like to be able to use the shortcut to disable the mouse momentarily whilst typing. My keyboard shows that if i press fn and F9 the i should be able to disable the mouse however the function doesnt work. all the other F9 functions appear to work.

Do you know if there is a resolution to this?

I am running windows 7 pro 32 bit service pack 1.

A:Satellite Pro S500-139 - FN+F9 button doesnt work to turn touchpad off

What you can try is to reinstall Toshiba value added package.

1 more replies
Answer Match 66.78%

I just purchased a click 10 and the touch screen does not work at all. IT says that there is no pen or touch available. I cant work out how to activate I have tried a whole host of things . This is the model where you click and the tablet separates from the keyboard but the tablet has no touch. Anu help would be greatly appreciated

More replies
Answer Match 66.78%

The glass on my Toshiba Satellite P840 has cracked - wondering what part of that is the touch screen - is it the glass - or the LCD under that.

More replies
Answer Match 66.78%

I am unable to use my touchscreen at all, this started happening around 2 months ago when my PC just suddenly crashed and wouldnt turn back on. This was fixed at a local repair shop, and they said there was too much dust on the motherboard or something.

After bringing it back home, the touchscreen was working fine. And then about a week later, it didnt work at all.
After some research on the internet apparently I seem to be missing the "Pen and Touch" setting and the "TouchScreen" driver under display in the device manager.

I have been trying various solutions from similar problems posted on different forums:
System restore to before laptop broke downDriverToolKit to search for missing drivers.Search Toshiba website for driversSearch through entire System for anything related to touch screen.

The last thing I do not want to do is Factory Restore the laptop because I do not want to have to reinstall Everything

More replies
Answer Match 66.78%

Hello, My laptop is HP Pavillion DV6875se with Windows 7 OS. It was working great before a month, but all of a sudden the following issues came up1. The power button of the laptop doesn't turn on/off the laptop. I have to use a detachable remote to turn the laptop on. I don't see blue light on the power key, once the remote turns the laptop on.2. The quick play touch sensative keys above the laptop key board have blue light in most of them. But its flickering red for volume, and no indicator on the volume increase decrease touch region. Though some have blue indicator, red lights....none of the touch sensative keys function at present.3. The laptop touch pad is unresponsive. It has its blue light, which doesn't turn red even if the touch pad is locked. I use a USB mouse as of now.4. Laptop has 3 audio jacks. One for microphone, and 2 for headphone. The external speaker doesnt have any sound, so i have to plug in earphone everytime to listen anything. In control panel --> under sound --> playback ---> i see speakers and realtek digital output ---> both show green oscillating bars when an audio is played. But the volume key in quick play tab is flickering red all the time. The laptop is fully functional. But it would be great if the problems mentioned above gets fixed. Sincerely 

More replies
Answer Match 66.78%

I have been facing this issue from the day one since I installed Windows 10 on my laptop (Dell XPS L502x).

Native Windows Applications like all browsers, office products etc. anything that is not from the Store, works fine. I can use Touch Pad scrolling with no trouble. e.g. on Internet Explorer, Chrome, MS Word, etc.

But the apps that come out of store or the apps like those which come pre-built with Windows 10 such as new Settings UI, Microsoft Edge. Touch Pad scrolling just don't work with these apps. When I perform scrolling the scroll-icon appears but doesn't scroll the content.

This issue is only with Touch Pad. External Mouse works great with scrolling on any kind of app.

Hope to find a solution here.
Thanks

PS: drivers are all good on the machine and up to date with no warning or error.

More replies
Answer Match 66.36%

The Wifi key light remains amber (orange) no matter how many times i press it . It only turns on and off the bluetooth. I have installed the Drivers from HP's site. The wireless lan card is not visible in device maneger . It only shows the ethernet port and the bluetooth. even after choosing the show hidden devices the wlan wasnt visibleI am checked the bios by pressing F10 at the bootup screen  and Wlan and Bluetooth Combo is ticked in built in hardwares. I installed Wireless Assistance software abd it showed Bluetooth to be enabled but Wifi to be disabled saying it had been disabled by device maneger .  and i cant find it in device maneger under any of the headingSo how em i suppose to fix itis it a software related problem .. or a faulty Wlan Card ??Whats the sollutionCompaq Presario CQ42

A:My wireless button doesn't work

I am having the exact same problem with an HP dv7-1135nr. I posted in another topic earlier but I didn't see this one before that. Mine will come back on a reboot sometimes but not always. I went to Administrative Tools, Services, WLAN autoconfig and turned it off, rebooted, still not working. Went back and turned WLAN autoconfig back on, reboooted, and it came back on. Really would like some help on this also. ThanksDavid

9 more replies
Answer Match 66.36%

Time for your daily chuckle. And when you're done, some assistance.

We have down here that received a popup on her computer screen while she was using access, she thinks. She either clicked yes or no on the message. She doesn't remember what the message said. She noticed several hours later that her right mouse button wasn't working.

I've been searching the internet for reactivating and inactivating right mouse buttons, and I see lots of things about hardware (which this isn't), and turning off the right mouse function in webpages, but not much else.

Anyone with a constructive suggestion, send it my way please.

A:Right Mouse Button Doesn't Work

What kind of mouse is it, USB, PS/2, wireless?

if you happen to have another mouse around, you could try that.
another thing you could try is to uninstall and reinstall the mouse drivers.

If no luck then,

if USB:
try another USB socket

if PS/2:
examine the pins in the socket, any bent?

if wireless:
it's possible that the mouse may behave oddly when battery power weakens. try replacing them.

1 more replies
Answer Match 66.36%

I have been having some other problems with my computer, in trying to resolve those issues I have lost the ability to use the All Programs button from the start menu. Other buttons such as control panel work, but not all programs.
I dont know what I did to cause this but if anyone can help with getting it back for me it would be appreciated.
It does not work in safe mode either, and I cannot restore my computer to an earlier date.

A:All Programs button doesn't work

Log in as an Administrator. Go Start > Run and typeregsvr32 /i shell32.dllReboot.

1 more replies
Answer Match 66.36%

I am fixing a PC for a friend; their power supply went bad, so i switched it but now the PC will NOT turn on using the front PC button but rather it turns on when i plug in the cable in the Power Supply.

& Furthermore, it shows nothing on the monitor when it turns on...

The Power Supply Fan is working, CD Drive open normally & i can hear the Hard drive moving...

Can you guys give me a bit of advance on what i should do next please?
 

A:Power button doesn't work with new PSU

Are you sure you plugged all the connectors correctly? The PC not switching on from the front button would seem to indicate the power switch is not plugged into the motherboard.
 

4 more replies
Answer Match 66.36%

Hello,
i have the MICROSOFT WIRELESS OPTICAL DESKTOP 3000 DSP and the problem is that
the mute button doesn't work. I checked with a program that tests buttons if the button have problem but it works perfectly. I just doesn't work in win 7. This problem came after a format. I have also tried through human interface device access to automatic startup but still nothing.

I have installed the latest audio drivers still nothing.
I can't find the drivers for the keyboard.

Any ideas appreciated.

Thanks!

A:mute button doesn't work

Not sure about the DSP part but I did find it for the 3000 series...heres the link. Just select your OS and bit type and download the exe.

Microsoft Keyboard & Mouse: Wireless Desktop 3000 | Microsoft Hardware

4 more replies
Answer Match 66.36%

I am having problems searching at yahoo or other search engines or just websites that have buttons that say search or yes or no or other junk like that. I click it and it doesn't do a dang thing. I'm about to go postal on my laptop so any help would be very much appreciated.
 

A:yahoo button doesn't work

any suggestions?
 

1 more replies
Answer Match 66.36%

Windows button does not do anything. Any help would be greatly appreciated.

A:Start button doesn't work

I would do a system restore to before the problem started.http://www.howtogeek.com/howto/windows-vis...system-restore/Check your power supply. Connection and cord.

1 more replies