Tech Problem Aggregator

Can't reach Belkin configuration page..is this a problem???

Q: Can't reach Belkin configuration page..is this a problem???

We have 2 wired pc, and a laptop. The PCs are Acer3100+, 1.8ghz, 1G ram, connected via ethernet to a wildblue modem. I have just installed a Belkin wireless router, model F5D 6231-4, that I bought on ebay. Both pcs will go online, a little slower than before, but my big concern is that when I run a cmd, ipconfig/all, my IP address dosen't match what they say. Belkin says it should be 192.168.1, and I get 70.41.xx.xxx, in this range. They said to configure router, but when I enter that page address, I get the notice of a network error. I don't know enough about this to know if this is a security issue or not! If I manually enter the numbers that Belkin should be , I get the correct address in an ipconfig, but I cannot get to the page, or get online. What have I done wrong!!!!

A: Can't reach Belkin configuration page..is this a problem???

the Belkin default address is 192.168.2.1

you're apparently wired like
modem---(wan)belkin-router(LAN)---yourPCs

the WAN side address will be set by your ISP, not belkin and might well be
70.41.xx.xxx, but none of your PCs will see this using IPCONFIG /ALL --
they will see the LAN side addresses. IPCONFIG will show the DHCP address
given to that specific machine. the LAN side address of the belkin should be
the default above, and thus your PC addresses will default to something like
192.168.2.x.

use one PC to access the router config using your browser http://192.168.2.1/
IF NECESSARY, you can change the default router address and the range of IP
addresses that will be assigned to your PCs.

you should absolutely change the admin password

2 more replies
Answer Match 78.12%

I moved into my dorm and was attempting to get my xbox360s nat to be open again and obviously failed.

I saw an option to simply shut the nat off, this seemed like a good idea, so i did that.

A message popped up and said to now access the page from the ip address via 192.168.2.254

it was previously 192.168.2.1

When i went to the new one it wont load.

What do I do?
 

A:cant access my Belkin f5d7230-4 configuration page

16 more replies
Answer Match 67.2%

my internet connection uses PPPoE to connect to the internet. i'm trying to set up the router for this configuration but it does not work. if there is anything else i need to post up pls tell me...help!!
 

A:Configuration problem for belkin adsl2+ modem with wireless router

the MODEM uses PPPoE, the router should not. the ADSL modem will hold the connection
regardless of anything being active on your router or systems, so imo, the router
should not be configured for PPPoE.
 

1 more replies
Answer Match 66.36%

Hello all,

I have a Belkin N150 Enhanced Wireless Router, my internet is dynamic cable modem, and I have two computers; one running XP and the other Windows 7.

On initial plug in, it was working. It was plugged motorola cable modem/belkin/windows 7 comp. I did the IPCONFIG, I ran the Setup Assistant, and I guess I entered the wrong information because the internet stopped working. So I had another go at it, and still wouldn't work. Third time, Setup Assistant tells me that it cannot detect the connection between the computer and router. It tells me to make sure everything is plugged. I haven't touched a bloody thing. All lights are green on router.

I tried to access the settings through 192.168.2.1 and other consecutive numbers, to see if I can reset to factory settings. My browser tells me I got nothing! I've tried on Chrome, IE, and Firefox. I've done the hard reset, lights go off and then back on green - one by one. Nothing.

I've googled the crap out of this issue (and browsed through this forum), and I'm almost down to return it. I have contacted Belkin through their tech support email, and haven't heard a response.

I connected it to my XP comp (which is not connected to the internet, because at this point my concern is accessing the router settings) and IPCONFIG says;

Connection specific suffix ; Belkin
IP Address: 192.168.2.2
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.2.1

I've tried to access 192.168.2.2 and it&... Read more

A:Solved: Belkin N150 EWR not detected, can't reach 192.168.2.1

You need to use 192.168.2.1 in the address bar of IE to access the router's setup if that is your current IPCONFIG.
 

3 more replies
Answer Match 64.26%

as i have chosen 150 % size , i cannot reach anymore the lowest part for configuration settings

so i cannot change it back

i am a first user for w8

how can i solve it ?

A:large icons cannot reach configuration

Can you get to Custom sizes?

See here:

DPI Display Size Settings - Change - Windows 7 Forums

2 more replies
Answer Match 63.42%

Hi,
1. I cannot find a solution for a problem accessing Microsoft forums websites from Windows 10 - IE11 and Edge browsers:
in EDGE - Hmm, we can't reach this page.   IE11 this page can't be displayed.
For about a year it worked at least from Edge. Now both cannot access Microsoft forums. All the other sites are accessible.
I am using a corporate proxy. The same sites are accessible from Windows 7 with IE11.
First I blamed our IE GPO with multiple settings. So for a test I placed my machine in Blocked OU (no IE GPO, proxy is set from different GPO).
Everything what I tried didn't help. The question: why just Microsoft forums (no other sites) are not accessible.
Did couple of tests from Windows 7 IE11 machines. The same Microsoft forums are perfectly accessible (all GPOs are applied).
Suddenly, found that one corporate Web App does the same : "This  page can't be displayed". On other Windows 7 it does work.
I am out of ideas now... cannot blame anymore our GPO or proxy...
Any advice?
Thanks



--- When you hit a wrong note its the next note that makes it good or bad. --- Miles Davis

More replies
Answer Match 59.64%

I have Windows 10 and get the following message repeatedly when accessing the internet.  How can I fix this issue?


?

Hmm, we can't reach this page.
Try this

Make sure you’ve got the right web address: http://www.dell.com
Refresh the page
Search for what you want

A:Hmm, we can't reach this page

gary47la,
Where you able to reach the Dell website yet? If not, can you get to other websites? You can click the link below and choose Windows 10 from the list and follow the information to resolve your connection issue,
Dell Networking and Wireless Support Center

1 more replies
Answer Match 59.64%

Hello
This post is in regards to a website that I'm attempting to access. Within the email there is a highlighted link "Store" where I access a link to purchase my photos.. Clicking on this link Message reads Cannot reach this page, Refresh or Search. Clicking on Refresh nothing happens, click on Search brings up all the connecting websites but each one I try to open they all show the same. Cannot reach this page. This website is the only one that shows that. All others such as My Bank , Kaiser etc all open without incident. I do not understand this .I tried everything I even sent an email to this company about this issue The email could not be sent either , Up until today I have had no problems with this company/website. What happened, and Why? I have Windows 10 Microsoft Edge

A:Cannot Reach this page

1) Right click the link, click on Copy Link, and paste it in the address bar. Does it look like a valid website link?
2) If so, search for, and open, on your computer
iexplore.exe
and paste that link there and try it, does it work?

0 more replies
Answer Match 59.64%

1. I can access http://www.qmiles.com. On this page you need to enter member number and pin code.
2. Enter any member No and pin code and login
3. Box indicates 'you are about to view pages over a secure connection'. Click OK
4. Requested page does not display. Status bar first indicates 'Opening page https://secure.qmiles.com/FrontPage.jsp', then changes to 'Connecting to 213.130.112.202', and finally 'Done', and displays a page saying 'Page cannot be displayed'

I use windows XP Professional with Service Pack 2 and Tiscali broadband. This same problem exists at 4 Tiscali broadband site I have checked in this area, but works OK at an AOL site, and also at 1 Tiscali broadband site a few miles away.
Can you suggest what I should do to be able to view the login page?
This is not a security or firewall problem, as the problem is present even when antivirus and firewall are turned off. As the site is accessible from another site, it does not appear to be a security problem. I can access the secure bank sites.

A:cannot reach a particular web page

I can get to first link but second IP comes as unavailable. Perhaps the page is generated uniquely based on input you provide when logged in and cookies you have on your machine. If you have a bad cookie or temp internet file the page cannot be generated. Try emptying temp internet files and deleting cookies.


Quote:




inetnum: 213.130.112.192 - 213.130.112.255
netname: Qatar-Airways-13443
descr: Qatar Airways-13443
country: qa
admin-c: AS8416-RIPE
tech-c: JL2798-RIPE
status: ASSIGNED PA
mnt-by: QTEL-NOC
source: RIPE # Filtered

person: Azam Shaikh
address: Qatar-Doha-Qatar Airways-P.O.Box22550
phone: +974-4496436
fax-no: +974-4496494
e-mail: [email protected]
mnt-by: QTEL-NOC
nic-hdl: AS8416-RIPE
source: RIPE # Filtered

person: Justin Lazar
address: Qatar-Doha-Qatar Airways-P.O.Box22550
phone: +974-4496436
fax-no: +974-4496494
e-mail: [email protected]
mnt-by: QTEL-NOC
nic-hdl: JL2798-RIPE
source: RIPE # Filtered

% Information related to '213.130.96.0/19AS8781'

route: 213.130.96.0/19
descr: Q-Tel New Allocation Block
origin: AS8781
remarks: Qatar ISP New Block - QA-QTEL-20020516
mnt-by: QTEL-NOC
source: RIPE # Filtered

1 more replies
Answer Match 59.64%

I have Windows 10 and get the following message repeatedly when accessing the internet.  How can I fix this issue?


?

Hmm, we can't reach this page.
Try this

Make sure you’ve got the right web address: http://www.dell.com
Refresh the page
Search for what you want

A:Hmm, we can't reach this page

gary47la,
Where you able to reach the Dell website yet? If not, can you get to other websites? You can click the link below and choose Windows 10 from the list and follow the information to resolve your connection issue,
Dell Networking and Wireless Support Center

1 more replies
Answer Match 58.8%

I have had this issue so much more often the past week with Edge than my entire time using Windows 10. Is anyone else seeing a increase in this? I cant tell if its a wifi problem (all my other devices using wifi are fine) or a problem caused by a recent update or what, but its so aggravating.

Any tricks or suggestions before I just ditch the Edge browser and rely only on Chrome?

A:Hmmm...cant reach this page

Well after installing Chrome I am also having internet problems. So it's not the Edge browser. Must be a driver. Can someone point me in the right direction to see if my drivers are up to date?

1 more replies
Answer Match 58.8%

Only happening with this one particular website, and NOT having this problem with any others; just this single one:
 
 
 

Hmm, we can't reach this page.
Try this
Make sure you’ve got the right web address:https://www.hidingthewebsitenameintentionally.com
Refresh the page
Search for what you want
 

 
That is when using Edge.  Similar type of messages happen when trying to get to the same page in Chrome and in Internet Explorer.  I changed the website name, giving a fake one instead of the real one.
 
My guess is that something is wrong at the website's end and not at my end since I can reach all other sites; just not one particular one.  Any good way to check on this?  Any other way of testing the vaidness or health of the website?
 
 
-  Just went to a different computer and tried the website again.  Same message, that site can not be reached, refused to connect.  The website must have the problem.

A:browsers say, "can't reach this page"

Try this.
 
 
 
 
http://downforeveryoneorjustme.com/

2 more replies
Answer Match 58.8%

I've set Google as my search provider in Edge. If I open a new tab and type where it says: Search or enter web address, I get:

Hmm, we can?t reach this page.

Try this
?Make sure you?ve got the right URL: http://windows%207%20iso%20download
?Refresh the page
?Search for what you want

If I click on the last option, a search opens in Bing.

This is driving me crazy!

A:Edge: Hmm, we cant reach this page?

Does Google look ok as the default search provider in advanced options?

I just tried

Went to Google home page
brought up settings\advanced
clicked the drop down for search box and selected add new
it showed me google was available and I clicked add as default

are these the same steps you took?

19 more replies
Answer Match 58.38%

?Constantly receive this message when on the internet...on a brand new H50 desktop?? Hmm, we can't reach this page.Try thisMake sure you?ve got the right web address: http://www.puritan.comRefresh the pageSearch for what you want

More replies
Answer Match 57.12%

Computer turned off in the middle of windows update. Now computer can?t get to homepage. Tried all F1-F11 options and received BSOD (Error code: 0x000000F4). Went to windows tech support and all of their tests point that it?s an HP issue. If problem persists, BSOD indicated to disable/remove any newly installed hardware/software and to disable BIOS memory options such as caching or shadowing. Ran all available HP tests (Memory, hard disk, run-in, start-up, and battery). All passed except for battery (failure ID: 9C0c13-00089U-Xd6V5G-C0F603) and run-in (failure ID: 9C0C13-00089T-XD6V5G-C0CN03) tests and both failure id description for these two said, ?Primary battery.? Computer was working just fine before this issue. Please help.

More replies
Answer Match 52.5%

Before I go into any further details, I'm going to describe the current setup.

Connected via ADSL, I have a BT HomeHub. This is the networks DHCP server with both wired and wireless connections. It came with static IP addresses/masks of:

10.0.0.138/24 (assuming that's for WAN)
172.16.1.254/24 (this is for the telephone handsets it also manages)
192.168.1.254/24 (for the LAN/WLAN connections.)

It serves two pools of DHCP addresses:

172.16.1.1 - 172.16.1.253 (handsets)
192.168.1.64 - 192.168.1.237 (LAN/WLAN)

Wireless encrytion in use is WPA2. A laptop, server and Wii console all connect to this via WLAN, with the router being configured to use specific addresses for each device. These all work perfectly.

Unfortunately, the Nintendo DS Lite handheld is not compatible with WPA based encrytion. So after mulling over spening money on the PC connector to let it hop on the connection, I decided to add a WEP access point to the network instead as I already had the hardware lying around. When I'm not using the DS online, I can just switch off this extra AP without disrupting the rest of the network.

This AP is a "Belkin Wireless G Access Point F5D7130". It is configured with a static IP address of 192.168.1.253, and is connectd directly to the HomeHub via cable. The HomeHub recognises its presence and static addressing.

Everything works. The Homehub recognises the DS as being connected through the cable (as the wireless AP is) and it can get online ea... Read more

A:Can't get to Belkin AP admin page

Did you try IE to connect to the AP?
 

2 more replies
Answer Match 51.24%

Last night since I was having slow/non-existent connection issues, I turned off the NAT option on my Belkin wireless G router. Immediately afterwards I lost internet connection as I expected but now can't connect to the config page @ 192.168.2.1 . I tried running the setup software again and it can't communicate with the router, either. Tried hitting the reset button several times, disconnecting the router, etc. but the config page still won't load. Is there anyway to manually revert the router back to factory settings?
 

A:Can't connect to admin page on Belkin Router

So this is with the pc connected directly to the router via an ethernet cable?
Go to My Network Places, and on the left theres a thing that says "show all UPnP devices" or similar. Click on it, then go to your LAN settings and set your IP address to auto, or 192.168.2.3 vice versa. Plug in/turn your router back on and it should come up as a network place. From that doubleclick it and enter admin etc..
 

2 more replies
Answer Match 51.24%

Hi, I am trying to set up a LAN with a Belkin router (F5D7230) where you are directed to a landing web page upon joining the network. The landing page will be a locally served page from a PC on the LAN. From looking at the config options in the control panel for the Belkin, I'm not sure how to set this up. I can access the web page I want to serve by typing in the IP address of the host machine (which is running Apache), but I need to specify somewhere in the Belkin config that this IP should be where people joining the network are directed to. Is this straightforward? Or do I need additional software? If I can't easily do what I've mentioned, the other option would be to set up a simple alias, e.g typing http://site would translate to the IP and page of the web page.

Thanks for any pointers.
 

A:How to configure a landing page on connecting to Belkin

try setting up Port 80 redirection
 

1 more replies
Answer Match 50.82%

Ok i'm new to all this, my belkin used to work fine then one day it just wouldn't connect to the internet so i tried fixing it myself the thing i regret and since that the computer has never worked i was doing wireless with it and they could share files but now the host computer works the other doesn't and on the belkin the lan 1-4 doesnt flash although the wire is connected need some real help it has annoyed me 4 the last 2 months plus the computer has important photos on just for people to be extra eager to help plz help !
 

A:My belkin icon says i'm connected, but the net explorer says page can't be displayed

raymond,

Please post your OS and ipconfig /all results here for the computer that works and the one that doesn't. You can easily do this by:

If winxp, 2k or NT:
1. Go to a command prompt and type: ipconfig /all > ipconfig.txt
2. open ipconfig.txt (with notepad) and copy all then paste to a reply to this message.
3. repeat for each system.

If you are using win98 or, gasp, win95 then the command is winipcfg and you will have to copy down that info and type into a reply.
 

2 more replies
Answer Match 50.82%

Hello all,

I'm having a problem with my Belkin N1 Wireless Router, model # F5D8231-4. I cannot seem to access the internal router's web-based settings and/or log-in page and I'm looking to see what I can do to get to these settings.

My router's default gateway IP address is 192.168.2.1 and every time I open up a browser to type this in, I come to this page:

There's absolutely nothing relevant on this page.

I'm running Windows Vista and two of my other networked machines run Windows XP and neither machine could access the setup page via the IP address as well.

Our wireless broadband internet connection is working just fine - I just can't access the router settings. Setting up our wireless security, port forwarding, etc. is impossible without getting to this page...

I have the latest version of Java and Flash installed, and my computer is as updated as it can be...

Any suggestions on what to do would be greatly appreciated - thanks!!!
 

A:Cannot access Belkin N1 Wireless Router setup page.

According to my manual, your IP Gateway is 192.168.1.1., not 192.168.2.1

Try entering that into the web location in the address bar.
 

3 more replies
Answer Match 49.56%

Hello everyone.
I am currently experiencing an error everytime I use my Microsoft Edge. Whenever I try to go to a site, I always end up with this error. The weird thing is, this issue only happens on certain websites (such as Facebook and Yahoo currently) and sometimes with Google. It likes to disconnect me often and I really don't want to have to deal with this issue anymore.

My internet works fine as my laptop (which I'm currently on) and phone can connect to it without issue. I don't know why it doesn't work on my desktop especially since its internet is Ethernet.

I tested this on other browsers to see if it was only on Edge but it turns out that chrome and firefox experience the same issue with different sites as well. For all three, I haven't been able to go on Facebook and Yahoo, and sometimes Google.

I know the problem is from my end because clearly, the sites are up. Is there any way to solve this or has anyone else found a solution to this?

I'm running Windows 10.

I've tried the following:
- ipconfig / flush
- ipconfig / reset
- ipconfig / release
- ipconfig / renew
- clearing caches and browsing history
- a full scan for malware using malwarebytes and windows defender, already removed/quarantined all threats, did this multiple times to ensure there were none left
- reinstallation of chrome and firefox and a reset of edge
- ipv4 - changing preferred and alternate dns address to 8.8.8.8 and 8.8.8.4 respectively
- checked to see if a proxy was ... Read more

A:"we can't reach this page" error

Hi. Welcome to TSF.

You mentioned threats were found by Windows Defender and Malwarebytes. Were they actually malware or just PUPs? A broken Internet connection is one of the common after-effects of a malware infection, and post-infection repairs need to be done, assuming all of the infections have been cleared. I advice seeking a clean bill of health from the virus removal section, and after they declare your system free from infections, come back here and we will advice further if the problem isn't cured.

1 more replies
Answer Match 49.14%

I cannot access the configuration page for wifi router...

my wifi router is buffalo WHR-G300N
I usually access the page via 192.168.11.1

but since I have plugged the wire from the internet socket on the wall to LAN port rather than WAN port and disable the DHCP , I cannot access the configuration page and I cannot change these because the ISP told me to do in order to access the internet

Is there any other way to access the configuration page?

if there isn't, how can I access to the configuration page?

i set it as AUTO at the moment

please help

Thank you
 

A:I cannot access the configuration page...

If you don't want to reset the router to factory default settings you can temporarily set a static IP (e.g., 192.168.11.11, mask 255.255.255.0) on a computer connected to the router.
 

1 more replies
Answer Match 49.14%

my xbox 360 online runs through my pc i've just changed to a wireless connection for my pc and now my xbox wont regester with my pc sayin it doesn't hav th ip adress and tells me to go to my router configuartion web page where do i find this?
 

A:router configuration web page

9 more replies
Answer Match 49.14%

I'm trying to install a wireless network for the very first time. I have cable modem service and I've installed my AirLink Wireless router without any problems. I can browse the web and access my e-mail fine through the router. My only problem is that I can't access the router's web configuration page. When I try to open it using IE, I get a "The page cannot be displayed" error page. (I want to be able to activate the WEP security, etc.)

I e-mailed technical support, and they said that it was probably my firewall causing the problem. I'm using Zone Alarm firewall and I shut it down and then tried to access the router configuration page again . . . . didn't work. (The Windows XP firewall is also disabled.) Any ideas?
 

A:Can't access web configuration page

Welcome to TechSpot

Did you try to enter that webpage as e.g. http://192.168.0.1 or whatever number as per your manual?
 

4 more replies
Answer Match 49.14%

I am using Microsoft Interner Explorer connecting to Bellsouth.net using Windows XP
Problem is not a big one but when I pull up my e-mail there used to be seperations between each e-mail....now there is only a white page with all of the e-mails without any lines between each e-mail. Spoke with bellsouth and they have NO IDEA. What do you say?
 

More replies
Answer Match 48.72%

Hi,

I use IE6 on XP Pro. I'm trying to set up a blank page as startup but whenever I open IE, MSN.com loads as default. Fix ?
 

A:Solved: IE6 start up page configuration

10 more replies
Answer Match 48.72%

I can't seem to access the routers web configuration page, I get a Gateway Timeout message. I tried rebooting the router, then rebooted my system, but still nothing. It worked fine a few weeks ago. That was the last time I remember using it. I'm not sure what has happened. I checked the TCP/IP properties and everything is set to contain an IP address automatically. Plus in the ipconfig the default gateway is 192.168.0.1

I am running windows XP and my netgear router is PR114

I did look around the site to see if this question was posted before, but I didn't find anything off hand. If this question has been posted before, please post the link.. Thank you..
 

A:Can't access router web configuration page

14 more replies
Answer Match 48.3%

Hi All,
Few days back I was able to access page by http://192.168.0.1 fro my Home laptop. That time I set WPA authentication for my router and was successfully using it. Today I was configuring my office laptop for wireless connection. I thoght it can only take WEP. So from my home laptop I accessed the http://192.168.0.1. I logged in successfully and changed security option from WPA to WEP. I provided key to it. And when I clicked on Apply button I got page not found. All of a sudden I lost my wireless network connection. I refreshed it and tried to connect it not getting connected. Not even showing any error message. I removed power supply from Netgear router. But it didn't work. I do have wired access but how can I get wireless access? Atleast I should be able to access home page. Its not even asking me user name and password. It shows page not found when I try to open http://192.168.0.1. Please help me....
 

A:Can't access Netgear login configuration page

try resetting your router using that button at the back that needs a paperclip thing. It will restore factory defaults with no passwords or anything. My guess is that you've enabled some sort of filtering and forgot to add your laptop to it (happened to me)

its either that or check the antenna if its detachable and the strength of the radio..
 

2 more replies
Answer Match 48.3%

Hello there! I have a question for the experts that I haven't been able to quite figure out myself. I apologize beforehand if this has already been answered--I searched, but didn't find any satisfactory threads regarding my issue.

I'm currently running Windows XP on a computer with a number of hard drives. Basically, the two main hard drives I'm working with are a SATA II (3.0 GB/s) 500 GB 7200 RPM HDD and a SATA I 150 GB 7200 RPM HDD. My question is, where are the best places to put the operating system, page file, and commonly-used programs so that I can optimize efficiency? I've heard that it's best to split the page file and operating system so they are on different physical drives if possible, but which should go on which, and should the programs be on the same physical drive as the page file (in a separate partition) or with the operating system?

Also, I'm thinking about dual-booting with Windows Vista. If I do this, should I match the configuration so that both operating systems are on the same physical drive, both page files are on the same physical drive, etc?

Any input on this matter is greatly appreciated!
 

A:Optimal Configuration for OS/Page File/Programs

6 more replies
Answer Match 47.88%

Is there a "F" key to hold down or some other methodology when starting up windows that will bring me to the BIOS page that gives the options of Safe Start, Start with Last Good Configurtion, of "Normal" Start?

Geoffrey1950

A:BIOS - how tofind page with START WITH LAST GOOD CONFIGURATION

F8 gives you safe mode option...Last known good configuration will pop up if windows isn't booting up, so if it is, its already a good configuration. Try the system restore utility instead (start->all programs->accessories->system tools->system restore), and for normal mode...you don't need to do anything :)

1 more replies
Answer Match 47.88%

Okay so I want to port forward so I can make a Garry's Mod server. I port forwarded for my Minecraft server like a year or two ago and it worked fine. But now when I try to put my default gateway in the address bar it just comes up with "Oops! Google Chrome could not connect to"

I went on command prompt and typed in ipconfig and tried like every number but it still wont work. Like I said I did this before for a Minecraft server and it worked fine. Please help I've had this problem for a while and have been using Hamachi but it's rather inconvenient. Thanks in advance
 

A:Solved: Can't open configuration page of default gateway

16 more replies
Answer Match 47.88%

Hi everyone,

I recently tried setting up a Buffalo WHR-G54s router on my desktop (which has Windows XP on it) so that I can access the internet with my laptop as well. I have no problems accessing the internet on my desktop after connecting everything, but I can't access the configuration page to set a password and change the SSID.

The default IP address of the router config is supposedly 192.168.11.1. However, when I run ipconfig /all, the default gateway is listed as 67.186.14.1. This IP address also pings successfully. Nowhere is 192.168.11.1 seen after running ipconfig /all.

When I try accessing either of these IP addresses in IE or Firefox, nothing happens. I even temporarily disabled all PopUp Blockers and shields (as far as I can tell) to see if that would help as well. But nothing seems to work. Anyone have any ideas?

Thanks!!!!
 

A:Cannot access configuration page of Buffalo Router WHR-G54s

12 more replies
Answer Match 47.88%

My computer is connected wirelessly to a Linksys router, which is connected to the internet through a modem/router that my ISP provided. When I enter 192.168.0.1, I am taken to the configuration page for my ISP's router. How do I access the Linksys router's configuration page?

I have tried all sorts of combinations of 192.168.x.x, but nothing has worked. Is there a way to figure out the address the Linksys router's configuration page? ...or is there a reason I am unable to access it?
 

A:Solved: Trouble accessing router's configuration page

9 more replies
Answer Match 47.46%

Ok so here's what's going on one of my computers (windows xp home professional I believe) I downloaded a pretty nasty virus by mistake and ran it (for some reason avg didnt detect it as a virus) well this virus may just of totaled my hard drive beyond repair I've researched on the web for people who have had it happen to them but found no easy answer. What happens is this:

1. I boot up computer
2. Computer gets all the way to loading bar
3. Quick Blue screen appears
4. BAM computer reboots endless cycle

Now I've made myself a winxp recovery cd (never had one in the first place) and have tried various commands to bring my computer to a working state to no avail

chkdsk and chkdsk /r return with something like "the system has unrecoverable errors"

bootcfg /rebuild returns with something about a problem with the file system and says to run chkdsk lol

I also tried a command to rebuild the boot.ini but it failed to...

I have been successful at getting windows PE to run by booting to cd drive

I tried chkdsk from there and still no good.

Safe mode returns the same results btw so thats out of the question.

ONE TIME I was able to start up windows in something like directory services mode but im not quite sure how :/ It just decided to show up on the menu with boot options on a try.

I've got like 40gigs of backed up data on there that I was *hoping* not to lose so this really pisses me off.

Also when I did get into windows that ONE time I sy... Read more

A:Solved: Serious Problem: Computer Can't even reach login screen.

16 more replies
Answer Match 47.46%

On my PC I use IE6, Opera & Firefox and, in none of them, can I reach affiliate links, that is when a site links to something I may want to purchase.

I also have affiliate links on my own Website at http://www.songland.com/ - if you go there, please click on one of the 3 main ways of entering the site (you can't miss 'em!) and you should see a vertical banner which links to iPowerWeb (excellent Web hosting company, by the way), which is further down in the light blue left-hand links sidebar.

I can't see that banner, in any of my browsers! Yet I can see it on my laptop. Both computers are running the XP Firewall, so it's not that, and it can't be IE6 because I've configured the security identically on both machines.

I seem to have something enabled or disabled somewhere. It could well be in McAfee Antivirus, which I run on the PC only. But, as is usual with antivirus software - always has been! - the interface is ghastly to use, and I can't even find how to configure the darn thing.

Any McAfee experts here? (If it IS that...).

Thanks in advance,

HumanBean21.

My setup:-

PC (not MAC) + Acer laptop
WinXP Pro
AMD Athlon XP 2500+ (1.83 GHz)
ASUS A7N8X Deluxe motherboard
Tascam US-122
Rode NT3 mic
1.00 GB of RAM
200 GB HD
 

More replies
Answer Match 45.78%

Hi, Earlier when i was on my routers setup page checking a setting I kept getting an error message only when trying to log off "duplicate administrator this device is managed by 0.0.0.0 currently". This kind of bothered me cause I hadn't logged on to the router page from any other computer and had just reset the router. After that I checked to see if remote administration had been enabled somehow and it was disabled. I also have a strong password and the security log showed no login attempts other than my own.
Sorry if this seems like a stupid or pointless question but I'm just really curious as to what could cause this.

A:Belkin router page giving "duplicate administrator" when logging off

Only thing I can think of is you didn't happen to have multiple settings pages/tabs open at the same time did ya ?

4 more replies
Answer Match 45.36%

Okay I assigned the access point a static IP 192.168.2.50 within the router IP range. My computer wireless card is detecting the access point but I can't get the belkin n600db to detect the access point.
 

A:I can't get my belkin n600db to detect my belkin f5d9231(access point mode).

14 more replies
Answer Match 44.94%

Hi Guys i am trying to setup my Broadband connection. i read the whole 510v6 manual but was not able to find how can i set the 510 v6 modem into bridge mode. Please help me.
 

A:Solved: connect Speedtouch 510V6 with Belkin belkin f5d8231

7 more replies
Answer Match 44.52%

i am looking for this product: Belkin Cable/Belkin Omniview CAT5 Extender

but i cannot find it, and the only one i find is in a uk online store i need one in the us. can someone please help out?
 

A:Belkin Cable/Belkin Omniview CAT5 Extender

I will try to find that for you
In the mean time , may I ask what you are going to use it for?
...or better what you would like to accomplish ?
also your network config
routers , hubs, PCs, peer to peer, domain..etc
is this it
http://catalog.belkin.com/IWCatProductPage.process?Product_Id=199221
 

2 more replies
Answer Match 42.84%

Hello All:

I purchased a Belkin Wi-Fi system for the office. I have two laptops, one running Wins 98 and the other XP. I can suft the internet fine. I can access hotmail and AOL webpages but I can not access the email accounts from both laptops.

I get the following messages:
The page cannot be displayed
The page you are looking for is currently unavailable

When I am connected directly to the DSL modem I can access everything just fine. I can get into the Hotmail and AOL email accounts.

Please help!
 

More replies
Answer Match 42.84%

Ok, I have Windstream DSL that connects through a Siemens 4200 modem that goes into my linksys wrt54g wireless router. So how exactly do I access the modem, if when I type in 192.168.1.1 goes to the router. How can I access the modem to port foward? The only current way I can get to access settings on my modem is to go to Windstream.net and go to configurations in the top right. From there I can access the modem. Is there any way to port foward with this modem?
 

A:[Siemens] Accessing Siemens 4200 configuration page with a Linksys router

11 more replies
Answer Match 42.84%

Hi everyone..

My external USb Wd mybook box has 1 tb Seagate Sata 3 and i use original Wd disc as W7 installed... in My PC Case as sata II

Today my old problem appears again as Corrupted disc...
I have Get Data Back NTFS (and i used before plenty of times for recovery, loss data or unwanted deletions) but..

This time im stuck.. Becouse the disk i try to recover includes 870 gb (about) used disk space (only audio files) only 50gb (about) empty space... Thats too big for me to recover to other disks.. i don't have enough spaces that my other disks can handle..

I have about 300 gb FREE disk space in several disks or partitions include My thinkpad SL510 Notebook..
---------
So my question is
wit keeping my lost data in corrupted disk first, can i take them slowly to this 300 gb spaces (i know i can) and after create somehow emty space (deleting those recovered 300 gb + 50 on corrupted disk) and
use that empty space for more recovery. ???? Or smilar solutions.. Becouse DISC PRICES IS HEAVY nowadays and really i'm out of budget with buying some
equipments upgrades..
----------
IS THERE ANY PRACTICALLY POSSIBLE SOLUTION even can take very long time..
Like creating slowly slowly some extra spaces (don't know how)

I know i look silly in situation becouse i know u should never write to same disc if you dont want to say goodbye to your files..

E-how happened (not necessary to read these part)

according my experiences Thats the mistakes... DOn't do those at the same tim... Read more

A:Data recovery problem, Can reach corrupted data but no external space.

Hi,

Before you write more data or attempt to read data from the drive through Windows, I would suggest using a Live CD like SysRescueCD to boot from and access the HDD.

2 more replies
Answer Match 42.42%

hi all
installed win7 few days ago managed to get almost everything working apart from one thing this belkin bluetooth dongle f8t017
most of the drivers install fine but i have 3 bluetooth devices with no drivers showing in the device manager despite the latest widcomm driver saying it supports win7

i know one of the devices with no driver is for pim transfer

would be grateful of some help

A:belkin bluetooth problem

manage to get the driver installed using xp mode but then it crashes explorer
when i try and go to my bluetooth places

6 more replies
Answer Match 42.42%

At home I have a network of 4 PC's, connected through a Belkin F5D5130. everything was working fine with no problems at all.

A few days ago I decided to get myself a new computer consisting of an Asus A7N8X motherboard, athlon 2600XP 333 FSB, memory and all the rest of it.

now a strange thing has occoured since I installed the new computer.

Every now and again the router will reset itself. all the lights will go on, then turn off, and then come back on again and start working again. Of course doing this causes an interruption with whatever i may be doing at the time.

If i take this computer off of the network, ithe router works fine. So I can only surmise that there is a problem between the computer and the router

Does anyoe have any ideas as to what may be wrong?.

Tsi
 

A:Belkin Router and New PC problem

6 more replies
Answer Match 42.42%

Hi there

I have a Belkin F7D2401 wireless router with built in modem. This has worked fine for a year since purchase. The router has a wired connection to my desktop (running Vista and IE), and was supporting a couple of Blackberry smartphones, a Blackberry playbook and a Kindle. At some point last week, all these devices lost their wifi connectivity. Yesterday, I noticed the WPS light was blinking amber at regular points.

Although I've next to no technical knowledge, I've reset the router using the button at the back but this hasn't solved the problem.

Can anyone help me understand what's going wrong, and more importantly how to fix the connectivity on our devices ?

Thanks

Grahame Blair
 

A:Problem with Belkin Router

sounds like the router is faulty

try powering off and leaving off for 15 minutes and see if that works again

you could then try logging into the configuration pages and disable the WPS facility and just setup the devices manually ,
connect to the wireless and enter the security key

see the user manual here

https://www.google.co.uk/url?sa=t&r...=_Q64A0N5hlTiOk45HTARwg&bvm=bv.55123115,d.d2k

The WPS light (small light above WPS button) will blink green while it listens for your Wi-Fi device. Once a connection is established, the light will turn green and then go out. If a connection is not established, the light will blink amber. You may repeat the process to try again.Click to expand...
 

1 more replies
Answer Match 42.42%

Hi i have BELKIN N1 PCI card (F5D8001uk) and i was wondering because i have many problems with this drivers (latest from site) if there is any other driver.

I heard about some models works better with RALKIN drivers. Is that true ? And if so does anyone knows which drivers is suitable for my card ?
 

A:Belkin driver problem

i had the same problem and decided to ditch belkin completely. Got a sweet new Zyxel router and adapter... and it was worth it
 

5 more replies
Answer Match 42.42%

Hi

I have just instaled a belkin router for a m8. Went through the set up wizard it comes to a point where it checks the connection from the router to the pc and it fails even though the pc has conected to the internet via the router ?

Also you cant have wireless and an ethernet connection at the same time, the router has 4 wired ports on the back if you plug one into the pc the wireless laptop wont work, when you get the wireless laptop to work the wired pc wont conect ?

Any ideas why ?

cheers

gus
 

A:Belkin router problem

could be a conflict IP, if you have set up manually - should be no need to use a CD to set up a router...

post an ipconfig for both the laptop and desktop - mark which is which

ipconfig /all

TWO Methods to do that - some people have

problems with ONE----

ONE ---------------------------------
start
run
cmd
ipconfig /all

rightclick in the box
select all
enter
control key + C key - to copy
then reply here and
control key + V to paste

TWO --------------------------------------------

---

Start, Run, CMD to open a DOS window and type:

IPCONFIG /ALL >C:\RESULT.TXT

Open C:\RESULT.TXT with Notepad and copy/paste

the entire results here.
 

3 more replies
Answer Match 42.42%

I am having the same problem with my belkin router please help.
 

A:Belkin Router problem

13 more replies
Answer Match 42.42%

Hi, we have a belkin f5d7230-4 router in our house which has been working for a week, but now its being an enormous problem.
We find only one of us seems to be able to connect at a time, and it only ever seems to be an XP computer that connects.
The setup we have is three wirless laptops and a desktop connected by an ethernet cable.
My laptop, XP, goes through a few different situations:

It connects to the router but doesn't have any internet connection (whilst only the other XP desktop does)
It sees the network but wont connect regardless of the WPA key
The successfuly situation where i get internet, but everyone else doesn't
The Vista laptops come up with an error relating to DNS problems, also on the diagnosis pages they highlight errors between the router and internet rather than the computer and the router, even though a computer in the house is usually connected.
My guess is that its unlikely to be the cable internet that comes into the house since one is successfully connecting, and its unlikely to be all of the computers simultaneously.
Thanks in advance for an responses!
Pete
 

A:Belkin Router Problem

Do a hard reset on router (straightened paperclip in the little hole for 30 seconds, with the power on).

Reconfigure the router. Make sure everyone has DHCP enabled (obtaining IP address and DNS automatically).

If it still doesn't work, you may have to get another router.

Courtney
 

1 more replies
Answer Match 42.42%

I have an issue with my router as far as connecting to friends over xbox live. My NAT is currently set to Open when I test connection, but I cannot connect to half my friends list. My connection is wired and also uses a generic arris modem which was provided by comcast.

1. I have port forwarded UDP 88, 3074 UDP and TCP, 53 UDP and TCP, 80 TCP
2. I have DMZ'd my xbox
3. I restarted/reset all hardware to default before doing the above
4. I have attempted to assign manual IP configuration to the xbox 360 without success
5. I have disabled all firewalls

I do not have a double NAT as my modem cannot be configured in anyway and is a generic pass-through device.

This is really bothering me as I cannot join up with many Moderate and Open NAT friends. My NAT being set to open should be able to connect to anyone who is set to moderate or Open NAT. The NAT is acting as if it is Strict even when it displays open.
 

More replies
Answer Match 42.42%

ok, first off i live in a dorm, and therefore am running off their internet. I have a belkin router ported in, and thus far all semester it has been working, all i have to do is log into campus internet then transfer the ethernet to the router. The router sends the ping keeping me online, so i can use this with my ps3. Well now ive encountered this problem: it registers internet, even the light says it has internet, but appearantly its not sending a ping, because i tried pinging google via command prompt, and it says error, timed out like 4 times in a row. Whenever it shows it has internet, it does not have wireless, yet its a wireless router. Any ideas? cause i'm clueless I've tried every troubleshoot i can.
 

More replies
Answer Match 42.42%

Firstly, the equipment:
1x belkin wireless router
3x belkin wireless dongles

So, my brothers Dell pc had been using one of the dongles for a year or so, as had my mum. They had worked fine, until he broke his. After that, he borrowed hers whenever it wasn't being used for work.
Recently, he was bought a new dongle. Same make and all that, but a slightly newer revision (And a different set of drivers to download from the belkin website). Obviously, plugging it in where the old dongle had been didn't work, so I uninstalled the old drivers, and installed from the CD that was supplied. Get the wireless zero config(WZC) back in charge, and look for the router. I see it and connect to it (Note: No direct router securite like WEP, only mac filtering, which works. The new dongle has been added to the mac list). It stays on 'connecting to network, the led doesn't flash. It just stays there forever.

However, after a couple of tries like this, my dad removed the dongle and put it back in the same slot while it was connecting, then it started flashing, and it got as far as 'Acquiring network address' before stopping. It wasn't sending or recieving packets, but it was still flashing.
Then it suddenly started recieving lots of packets, and it all worked. Internet sites loaded, but it was still not sending any packets, apparently.

So, restarted the PC, and it wouldn't speak to the router. Unplugged it and stuck it back in, and it connected to the router, but this time its stuck... Read more

More replies
Answer Match 42.42%

Hiya

First time user so be gentle!

I've been using a Belkin router for a couple of years, No problems.

I have also got a Netgear router that was sent to me by my provider, Orange.

Whilst using the Belkin as normal, it for no reason stopped allowing me to access certain sites. i.e Eaby and Facebook. but other sites are fine.

After calling Orange ( again...always have issues) and installing the router they supplied, it works and those sites can be accessed.

however, that router has a range which reaches just past my arm! useless. and I can only get a very weak signal in parts of the house.

So,.. The Belkin is being selective on what it wants to access. would it be needing a software update? Have Ebay and facebook done something to their sites? and why would the router not work on some sites but would on others.

I really don't want to buy another router. Any help appreciated.

cheers

RB
 

A:Belkin Router problem

Make sure you have the latest firmware for the Belkin; then reset it to factory defaults and reconfigure.

If that doesn't get it working then try using the Netgear as your router and the Belkin as a wireless access point and ethernet switch. You can also turn off the Netgear's wireless.

Your Belkin probably has an AP Mode; if it does that should work. If that mode does not exist or doesn't work the way I think it does here is a general procedure for any router.

JohnWill's procedure (Aug. 30, 2008) for configuring a secondary router as a switch and, optionally, wireless access point follows.

Connecting two (or more) SOHO broadband routers together.

Note: The "primary" router can be an actual router, a software gateway like Microsoft Internet Connection Sharing, or a server connection that has the capability to supply more than one IP address using DHCP server capability. No changes are made to the primary "router" configuration.

Configure the IP address of the secondary router(s) to be in the same subnet as the primary router, but out of the range of the DHCP server in the primary router. For instance DHCP server addresses 192.168.0.2 through 192.168.0.100, I'd assign the secondary router 192.168.0.254 as it's IP address, 192.168.0.253 for another router, etc.

Note: Do this first, as you will have to reboot the computer to connect to the router again for the remaining changes.

Disable the DHCP server in the secondary ro... Read more

1 more replies
Answer Match 42.42%

I have a wireless belkin router and aftre logging in clicked on the reset default settings button. The router rebooted but now I can't log back in to the router - it just gives me the address not valid screen.

Would appreciate any help
 

A:Belkin router problem

Router's model? Your OS and service pack level? How connecting?

Start, Run, CMD, OK to open a command prompt:

Type the following command:

IPCONFIG /ALL

Right click in the command window and choose Select All, then hit Enter.
Paste the results in a message here.

If necessary use a text file and removable media to copy the results to a computer with internet access.
 

1 more replies
Answer Match 42.42%

Hey guys,

i have a problem with my belkin router . When i open the ip of the router it says downloading 12942kbps but I download from my browser only with 80kbps at maximum. How can i make it give me the total speed of my internet connection i have close the 5ghz connection in order to speed up the 2.4ghz . What can i do to speed up my connection?
 

More replies
Answer Match 42.42%

I am having a problem getting a Compaq Presario running Win98SE to recognize a Belkin F5D7000 version 4 wireless networking card. I am trying to set up a wireless home network with 3 computers; 1 WinXP with a AOL broadband connection and 2 Win98SE. Had trouble installing router on XP...then it worked after reinstalling it. Now having trouble installing network card on 98SE. CAN ANYONE HELP???
 

More replies
Answer Match 42.42%

Hi guys, I'm new to the forum

I just bought a belkin surf n300 2 weeks ago. In the first few days, it works fine. But then it starts to disconnect without a cause frequently. During the night, the day, the morning, evening, just random times. So I got into the router settings and set up wpa2, updated my firmware (yes, from the belkin site itself and yes I updated AFTER downloading the firmware), set my self healing stuff at 3.30 am everyday. Then I thought its gonna stop but after only 6 hours of happiness, it starts again. So I restored to the factory defaults, set up my info again and using PPPOE connection type (My house have multiple wireless users). All of the users got Windows 7 installed. It slows down a lot when I patch my online games and download windows update. The router is connected in the same filter as the home phone.

Things that occur when my internet disconnects
-The router's light is red (Happens 1/10 times)
-The belkin manager program said the password has been changed (8/10 times)
-The wireless icon got a yellow triangle with a ! in it (7/10 times)

Note: -No coffee machine working when it disconnects. xD
-Phone is not used when disconnection happens.

Thanks
 

A:Belkin Router Problem

Sounds defective. Updating to the latest firmware and then reset to factory default settings is proper, and pretty much all that can be done.

Which router light is red?

A few ISP's require that the device connected to the modem be registered with them. With most of those a new device--e.g., your new router--would not get a connection, but with a few it will get a connection but then when the ISP makes a "sweep" to check for attached devices you would get disconnected. Make sure this is not your situation before believing my claim that the router is defective.
 

2 more replies
Answer Match 42.42%

I'm using windows 7 64 bit and its working fine except one problem. I have a belkin fd8055 usb wireless adapter. It acts just like it did in vista 64 bit sp2 when it boots from a cold boot. While booting, the little internet strenth bars on the bottom right side start menu has a little blue hour glass hovers over the strenth bars Then a red x appears. I then have to replug the adapter into the next usb port over from it. The little blue hour glass hovers over the strength bars then a yellow symbol appears then it connects. I've upgraded drivers from belkin still I have to replug the usb adapter every time I cold boot.
I would appreaciate the help. Thanks

A:Belkin wireless problem

Two things:
Are all your drivers up to date?

What are the Power Management settings like? Control Panel>Device Manager>Network Adapters>Power Mangement

3 more replies
Answer Match 42.42%

I hooked up a Belkin model FSU021 USB 4-port hub today. Sofar, I cannot get the computer to recognize the hub.......device manager says unknown device and it (the hub) doesn't light up except briefly on startup. I am running Win98SE, 500mhz AMD, 64ram. Here is what I have done.......the Belkin site said it should just plug and play but if not. Use the Win98 cd-rom. copy the usb.inf file and put it in the Window/INF directory. I have done that and then going into device manager and clicking on the unknown device and selecting the windows wizard I have pointed it (the wizard) in the direction of using the usb.inf file for the hub........but it still doesn't recognize it. Any suggestions?

Thanks in advance. Larry
 

A:[SOLVED] Belkin USB hub problem

16 more replies
Answer Match 42.42%

dont know if any1 can help me with this. recentley did a complete reinstall of windows xp sp2. After a total system meltdown.
have 2 computers my sons normaly conected through wirless still works fine. and mine normaly coneccted through lan cable to belkin ADSL modem with built in router. for some bizar reason i just cant get the lan to connect the icon in the taskbar says i am connected at 400 mbps but i just cant get through to it.
cant even acces the router.
if i plug the wirless dongle in no problem. it works straight away.
any help with this problem would be appreciated
I have tried turning of the firwall before any 1 suggests it
thanks
 

A:belkin router lan problem

sounds like the Ethernet adaptor is not configured to use DHCP.

with the cable attached, get a command prompt and enter
ipconfig /all
you should get somethink like
Dhcp Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
IP Address. . . . . . . . . . . . : 192.168.0.4
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : 192.168.0.1
DHCP Server . . . . . . . . . . . : 192.168.0.1
DNS Servers . . . . . . . . . . . : 24.48.217.227
24.48.217.226​
 

6 more replies
Answer Match 42.42%

Hi all,

I have a feeling this may not be a new problem so hopefully someone will have a quick-and-easy solution. I hope so because I am close to throwing my nice new Sony Vaio out the window ...

Until very recently buying the new laptop I had been running Windows XP. There had been a problem with the old machine and the Belkin wireless router (model no. FSD7633-4) accessing certain websites such as Hotmail and receiving email with MS Outlook. This problem was solved by downloading DrTCP and resetting the MTU level to 1400.

(Incidentally, if any of the foregoing suggests that I know what I am talking about - please accept my assurances that I don't. I am a computer ignoramus.)

The new Sony Vaio has Vista pre-installed. Although I have a seemingly normal interconnect connection and can access the majority of websites there are some such as, again, Hotmail which I cannot access. And I cannot receive email via Outlook. From what I have read, the DrTCP program does not seem to work with Vista although I have tried this.

Can anyone help me? Thanks in advance and if you need more info just let me know.



John

More replies
Answer Match 42.42%

I recently bought a Belkin 802.11g wireless key and everything was fine until 10-15mins in to surfing when my computer would freeze up completely. Ive come to the conclusion thats its a compat prob with the key and my computer but i would like to know if theres a way to solve this problem?
 

A:Belkin Wireless Problem

What operating system are you running?
 

1 more replies
Answer Match 42.42%

Hi. I'm working on a laptop IBM Thinkpad with Windows 98 installed. They are using a Belkin F5U222 USB card and have a mouse attached to it. Their problem is that the mouse occasionally freezes and the only solution is to reboot the computer. In device manager the Belkin shows as not having the drivers installed. I found the correct driver on driverguide.com and downloaded it and installed it but nothing changes in device manager.

I have read in another thread that the problem may be that this particular card does not work with Windows 98 only Windows 98Se and up. Can anyone confirm this or make another suggestion.

Thanks

theolddog
 

More replies
Answer Match 42.42%

Hiya guys...

I'm starting the new year with a new tech problem. Ugh. I hope everyone had a great holiday and I wish them well. Hope the new year was good as well. In any event here is the question.

I have a Sony Vaio VGN-SZ645 laptop. I use Windows XP. I love it. I bought the Belkin Hub-to-Go in order to manage all of my usb needs (in which I have a great deal). The Hub-to-Go worked great with my desktop at home which was a 3-5 year old Dell. I just hooked it up and it was ready to go. I attempted to this on my laptop and nothing. It at first recognized there was a new hardware but it couldn't find a driver for it. I also looked on the Belkin site for a driver for the hub-to-go and nothing.

I called the Belkin company and they said since it worked on your desktop the problem is not the Belkin. The problem lays with the fact I need to install a "generic USB drive." They told me to call microsoft but microsoft is charging like $40 for a service call. In any event, the Belkin does turn on when plugged in. And as I said the computer at times recognizes it...it just can't find the driver and turns up flat.
Any help would be great.
 

A:Solved: Belkin USB Hub problem..

15 more replies
Answer Match 42.42%

I have a Belkin 54G wireless router that I use perfectly well on windows vista but cant seem to get working on windows 7. I have tried to locate a driver and then download it onto my laptop so I can transfer it onto my new system but to no avail. I have tried to get onto the 196.168.1.1 page but it won't connect. Any ideas

A:Belkin 54G windows 7 problem

Hi and Welcome to TSF!

Is this for WiFi or Wired? Have you tried to update your wireless/LAN driver?

1 more replies
Answer Match 42%

I purchased a Belkin Nostromo n50 game pad for my Dell Inspiron 8100(Win XP Home) several months ago. Unfortunately I've not been successful in getting it to function properly.
The Nostromo software will not consistently load game profiles and when it does it either locks up the PC immediately or when the game is started the game crashes. (And the games run fine when the gamepad is not used.)
I've uninstalled the thing a number of times and reinstalled it - with the same results. I've downloaded the latest version of the software and driver from Belkin - with the same results.

Is there anyone out there that has gotten one of these things to work with WinXP and if so how?

Thanks.
 

A:(Resolved) Belkin Nostromo n50 problem

Well it looks like I finally fixed this thing. I downloaded the latest version of the Nostromo Profile Loader (version 2.3) and installed it yesterday (even though I'm positive I had done it before) because I apparently only had the 2.2 version.

Once I did this and rebooted and it now works as it should. The odd thing is that the Profile Loader software still says that it is only on version 2.2 not the 2.3 I just installed. Oh well, as long as it works!!!!!
 

1 more replies
Answer Match 42%

Right now I have my computer hardwired to a belkin G router. The only problems with this router right now for me are that sometimes the connection to the router flickers when I play a game. It kinda works but it just sometimes disconnects and reconnects. It causes me to disconnect from the game. However when I use firefox pretty much everything loads.

Oh and except for youtube. I'm not sure if this is supposed to happen but when I try to watch a youtube video it stops before it completely loads and just ends there. I don't think this is from youtube's servers because it's been happening to me for a couple of days now.
 

A:Belkin wired router problem

8 more replies
Answer Match 42%

Recently, i bought a new BELKIN wireless g adapter. The adapter keeps on dropping connection and i can't even download a 200mb file without it dropping. My friend has that adapter and somehow he made it work but he says it was like 2 years ago, he can't remember how he did it. Can anyone PLEASE say how to fix it because i can't be bothered to look for another adapter

Thanks

A:BELKIN Wireless G Adapter Problem

I'll be watching this thread, because while I can't offer any help, I've had a similar problem with a Belkin N adapter. I don't think that it is as bad as you described, but that makes it no less annoying.

3 more replies
Answer Match 42%

I recently upgraded my router from a model 2-3 years old to the belkin N1.
My previous model had some packet loss in one room but that was due to quite a few walls being embetween, I started to use it in a different room and it performed perfectly. Now I have upgraded I get often very bizarre pings to my router such as:

Pinging 192.168.2.1 with 32 bytes of data:

Reply from 192.168.2.1: bytes=32 time<1ms TTL=64
Reply from 192.168.2.1: bytes=32 time=112ms TTL=64
Reply from 192.168.2.1: bytes=32 time=135ms TTL=64
Reply from 192.168.2.1: bytes=32 time=159ms TTL=64

Ping statistics for 192.168.2.1:
Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
Minimum = 0ms, Maximum = 159ms, Average = 101ms

I was used to this in the room with a bad signal but the software im using shows a good to very good signal with good speed. The use of just browsing the internet doesnt seem too affected but when i try to play a game that ran fine with the old setup I get bad packet loss and a pretty unstable ping. Tried changing the channel being used as netstumbler showed a different network using the same, but the signal then just seemed to get worse (just changed from the router setting, couldnt find it within the network card advanced options). Dont want to fiddle with any of the settings within the router options as i dont really understand them any advice or further questions welcome thanks.

ps: my ipconfig /all

Windows IP Configuration

H... Read more

A:wireless problem with new belkin N1 router

16 more replies
Answer Match 42%

hi there!
i
got the above router, and i want to use the eMule program.
i constantly get a low id, and when i test the ports in the program it says that : "If you use a router, make sure that your router forwards the required ports to your local IP"
the ports are 4662 for UTP and 2673 for UDP.

HELP ME!!!! :-(
 

A:Belkin wireless G router problem

Sorry, TSG does not provide support for P2P software issues.
 

2 more replies
Answer Match 42%

Hi,

Basically i am trying to encypt my belkin wireless adaptor and am having a few problems. On my main computer I have an orange Livebox (router) which my second computer using the belkin adaptor connects to. The orange livebox is encrytped fine. I only found out today by pure chance that my belkin adaptor is not encrypted. I have just purchased a laptop and connected to the belkin adaptor without even doing anything!!

I have tried to work out how to add an encrytpion but its really complicated with me being such a novice of wireless networks. I have had a look at the Belkin user manual and to be honest its not much help. Its probably something really simple but for the life of me i can't figure it out!!
 

A:Belkin adaptor encryption problem

Hi
Depending on the os you are running on the laptop, running wpa/tkip security would probably be best as wep is insecure. How are your routers configured? Does one provide connection to the other? I would also disable ssid in the wireless router, and set a mac filter in the wifi router only allowing my laptop's mac. You might want to read up on how all these settings are made, here is a page on wpa/tkip to get you started:

http://www.microsoft.com/windowsxp/using/networking/expert/bowman_03july28.mspx
 

2 more replies
Answer Match 42%

I have got myself a belkin router and connected it to my main desktop pc. I bascially want to make a wireless connection between my pc and laptop. I got given a belkin network card too which if I put into my usb drive allows me to connect to the net. I can put the card into both my laptop or desktop and can connect to the net except I cant seem to do it when I only have it in one.

I am looking over the manual for the router and in the part configure your router it says
- In order for your computer to properly communicate with the router, your computer's network ''TCP/IP/Ethernet'' setting needs to be Obtain an Ip adress automatically using DHCP''- How to do I set it and where??

Then it goes onto say you can access the web based management interface of the router using internet browser on a computer physicsally connected to the route. Tpe 192.168.2.1 into your adress bar and click enter. I did it in aol and it takes me to some search site.



Can I actually connect the desktop and laptop without the belkin card and just via the router and also how the hell do i do it lol?
 

A:Belkin wireless network problem

ok....
1. connect the router to your pc via cable first.
2. Make sure the tcp/ip settings in the network connection you use is setup to 'obtain automatically' for ip address and dns.
2. In a browser window, type in the ip address of the router home page; 192.168.2.1. It should take you to the Belkin Router config page.
3. Setup the router for DHCP. Some Belkin's take abut 35 secs to accept and reset the router after each change (for some strange reason!)
4. Setup up wireless networking, MAKE SURE you enable the security on it.





I got given a belkin network card too which if I put into my usb drive allows me to connect to the net. I can put the card into both my laptop or desktop and can connect to the net except I cant seem to do it when I only have it in one.Click to expand...

I got a little confused here. Is the wireless card you have a usb plugin? Which can obviously fit into a usb port on either pc or laptop?
Well, with only one wireless card, you can obviously only have one wirelessly connecting to the network/internet can't you?
The router will most likely have 4 RJ45 ports in the back, so you can plug the pc and laptop into them with cat5e straightthrough cables.
From then its just a matter of sharing resources on the pc and laptop between each other.

Hope this helps.
 

17 more replies
Answer Match 42%

Hey guys, got me a new Modem not long ago and recently plugged it in, seemed to be working fine at first but every now and then something happens and it seems to disconnect. It says its still connected and everything and going into status it says it's connected fine, it seems to just stop for a while then comes back on after awhile. Unplugging and Rebooting it does nothing.

I know its the Modem because I had a different modem plugged in before and it was fine. It is a Belkin f5d5730au and is connected to a CNet CNAP-711 11mbps Wireless Router. Also, when another computer is turned on, it doesn't seem to allow it to connect for a small while then works.

Any ideas? Thanks.
 

A:Belkin f5d5730au Connection problem

I suspect you will benefit from a close read of all the documentation of your cable modem, and wireless router... and possibly with a talk with your IP provider tech support.
Are all of your old connections deleted in the device manager, registry, and the network connections in the control panel.
Belkins are sometimes weird devices... units with the same part number don't even look the same sometimes. Belkin doesn't really make anything. They pay to have their components made by others, to specifications they set.
If there is a problem, I would change out the Belkin for a standard unit by 2Wire, LinkSys, D-Link, Netgear, Siemens, or preferably Cisco.
 

2 more replies
Answer Match 42%

After enabling the WPA-PSK encryption and giving a nice long Password, I can not log on to the now protected network. I think it accepts the password, but it trys to aquire network settings, and fails after a while of trying. What is it that i must do? Im new to Wireless configurations. Thanks heaps
 

A:Enabled Belkin WPA-PSK encryption Problem

10 more replies
Answer Match 42%

Hi everyone,

A couple of weeks ago I bought a Belkin Wireless G router with a Belkin USB Network Adapter for my daughters com. I have the router up and running ok on my com, but I cant seem to find the installation disc that came with the network adapter that I plan to add to my daughters com.

My question is, can I still install this adapter without the installation disc? I found the driver page for it, but nothing else (see below).

http://web.belkin.com/support/download/download.asp?download=F5D7050&lang=1&mode=

Ill be using it on a com with Windows/ME installed and the model# of the Belkin Adapter is F5D7050

Thanks!
 

A:Belkin Network Adaptor Problem

7 more replies
Answer Match 42%

Hi, I'm havin a problem with my dads wireless connection. He has a belkin 54G wireless desktop card, and a netgear wireless notebook card. They both communicate fine(a bit slow but fine) as far as filesharing is concerned, but the laptop cannot connect to the net. The desktop has the adsl connection through a usb modem, and i have tried enabling ICS on both the ADSL connection and the wireless connection, neither worked. If you need any more details please post.
Thankyou in advance for your help!
 

A:belkin/netgear wireless ICS problem

You would be better off with a Wireless router. ICS is a pain in the butt.
 

3 more replies
Answer Match 42%

Please help!!
I recently installed a Belkin F5D9630uk4A ADSL2 + Wireless router to replace my AOL supplied DSL modem. I have a desktop and laptop connected.

The problem: Using the router I cannot get access to certain sites via IE (although I can if I login to AOL) BUT MORE IMPORTANTLY i cannot get windows or mcafee updates.
If I disconnect the router and put the DSL modem back in, without changing any othr settings I can again get access thru IE and get the updates. The problem is the same on both my pc's. I have tried turning off my firewall(mcafee) and firewall on the router. I have tried adding the microsoft websites to trusted sites. When I try to browse I get message "Website found waiting for reply". Trying to get windows updates manually I get
0x80072EEC, but the suggested fixes dont work. The problem is the same with either wireless or ethernet cables.

Is my router blocking some ncessary access back to my pc's? If so where is the problem and what should I do about it?

Thanking you in advance.
 

A:Belkin Wireless G+MIMO problem

Well, you mention AOL, perhaps there's some oddball thing they need. I wouldn't put it past AOL to make it difficult to use anything but their junk.
 

3 more replies
Answer Match 42%

Hello!

I have a Belkin wireless router that fails to connect to the internet which is the final step in the installation process. All the connections are correct. It will try to connect to the internet up to ten times but still there is no connection. I even tried installing it on my wife's laptop but still the same problem. I already checked all the cables and they all work correctly.

My computer can detect the wireless connection, connect to it, and even access the control panel through 192.168.2.1 but the green light (on the router, which refers to Internet) doesn't blink at all. I tried connecting the cable modem directly to my PC and it works perfectly.

Can you help me?
 

A:Belkin Wireless G Router Problem!

6 more replies
Answer Match 42%

Hello everyone!

I have a d-link ADSL Router and a Belkin Wireless Router. The PC is connected to the ADSL router through the belkin wireless router as shown in the BELKIN EASY INSTALLER. The problem is i am not able to access the net from my laptop through the wireless network but can access net from my PC(otherwise i couldn't possibly writin this!!!).

Basically the problem is that the easy install wizard gives the error: ERROR COMMUNICATING WITH ROUTER.

The "connected" LED is always blinking whereas all the otehr are solid(WAN, WLAN etc) ANyone knowing about this . . . pleaseeeeeeee help!


gthm
 

More replies
Answer Match 42%

Apologies if this is already threaded somewhere else; please link me to a solution if so.
I am currently setting up a new Belkin Wireless Router with built-in modem. It is an "N+N 2x300" dual band router for ADSL broadband connections.

The problem I am having is getting my Vista laptop to link up with the router and connect to the internet, using the Belkin software's router set up.
The router has been set up and is now working on my father's Windows 7 Sony laptop. However, originally the router was unrecognised by both the Vista and Windows 7 laptops. I accessed the router management and changed the 2.4Ghz channel. This made both laptops recognise the wireless network/router.

I then ran the set up programme, through the Belkin software, on the Sony Windows 7 laptop. After a couple of attempts it recognised the router and successfully connected to the internet. This laptop is now linked up and working well. Both the laptop and router have been restarted several times and connect again without problem.

I am now running the same process on my Vista laptop. However, the Belkin software's set up process fails to connect to the internet and complete the set up process. I have re-run this process about 30 times now.

I have tried alternative channels, restarting both pieces of hardware and have disabled all of my Norton stuff (as far as I can see). I am now at a loss. So I have turned to this forum for help.

Please can you help?

Thanks in advance... Read more

A:Belkin Wireless Router N+ Set Up Problem

6 more replies
Answer Match 42%

Evening all,

I had to do a restore of my system after a problem, and I'm now having problems accessing my net router.

The router itself seems to be all set up correctly, it's one that is used with cable connections, and in the interface it shows as having an internet connection, and when the laptop is wired into the router I can access the net but wirelessly I can't.

I've set the router up to use a 128 bit wep key for protection, but when I go into the network bit where you can see the available networks, when I click on mine it doesn't ask for the WEP key. Instead it asks for a username, password and domain.

I did try to connect to it earlier but couldn't remember the wep key so I had to reset the router, so is there a chance that the laptop is still trying to connect to the old settings? How do I go about searching for new networks as I can't see an option as I'm hoping if I can delete it and then find it again I should then be able to log on.

The laptop has built in wireless which I'm using, along with the vista network software for connecting to networks.

Thanks

Lee

More replies
Answer Match 42%

hey everyone,

I'm not very knowledgeable in the field of networking, so bear with me. I have a home wireless network set up with a NetComm NB5Plus4 modem router, a Belkin 54g wireless access point and several NetComm NP285 wireless 'homeplugs'. (you plug them into a power socket and one into the router and the others into the back of whatever you want to use wireless on.)

A while back I tried to connect the Homeplug from our PC into my xbox to access xbox live. however, I couldn't get it to work, and after following the instructions on xbox.com and power cycling the router and 54g returned it to the PC. however, when I plugged it back in, the PC said that it had limited or no connectivity. On trying to repair the connection, it could not renew the IP address. The wireless connection works perfectly on our laptop (with its own internal connection to the access point), but when I pinged the 54g's IP the PC and got nothing back except for a message reading "destination host unreachable".

I can't use any internet features at all. I'm using my laptop right now.

I have also tried the release/renew method. It couldn't connect.

any help would be MUCH appreciated as my laptop doesn't run games very well, and has some overheating problems.

thanks in advance

Edit: I pinged the 54g with the laptop and got all of the packets back.
 

A:Belkin 54g and NetComm Adapter problem

Unplug/plug the np285 adapters to reset them.

I assume the np285 adapters came with a utility program that repairs its connection and it surveys the homeplug network for addressable plugs. Use the utility to enumerate what plugs are still working in the network.
 

11 more replies
Answer Match 42%

Hi all members.

I read alot topics on this forum to try solve my problem. I found in here 2 topics about Belkin Wireless G USB adapter , but still i have a problem

I describe whats the problem .

I try to instal on my Windows 7 x64 b.7000 drivers for belkin w g usb adapter f5d7050

I download drivers 4 belkin usb adapter f5d7050 ver.3(like I read about it) - before install i change in install file the compability for all users to windows xp , but it dont wanna install(I get a error)(the product only supports Win200/Winxp32/Vista32/Vista64) , then i switch compability for windows vista and instaler go on,
While installer is going it ask to connect adapter to usb ,what i do, but it seems dont find any anyway .
After all when instalation is finish i just get information that device dont work proply , and the light in adapter never go on

I try update drivers from menage device but still device is not working

I really dont know what else i can do

Mayby that will be some clue
i install Windows 7 on separetly partition "E" , so I have on c: vista , and on disc e:Win7 , but in windows 7 mode i cant see partition with Windows vista(I can see just in Disc menagment, that she still there),
. when i open windows vista i see all partitions.
did it make any sense?
I can make some screens if it help .

anyway my main problem is to instal belkin drivers 4 adapter to WORK fine,

Please help, and sory for my english but thats my second language

Regards tasman

A:BELKIN Wireless G USB adapter Problem- again

When you did the update driver in the device manager did you browse to the belkin folder in your program folder.

I never had to install the driver with any compatibility. I just installed it then I just updated the driver in the device manager and going into the program files/belkin/model number and then it started to work.

5 more replies
Answer Match 42%

Hi i have Belkin N1 MIMO wireless router and until last night was working fine. I decided to download and install the latest firmware but now the router isnt giving off any signal what so ever. My Laptop, PS3, And PSP cannot detect anything. It's like my router isnt even switched on. I have restored factory defaults, reset and done everything really to try and fix this yet i still cant get it to work. Help please, please dont say the basics such as reset, or make sure broadcast SSID is on coz it is. Thanks in advance
 

A:BELKIN 1 MIMO Problem: No Detection

8 more replies
Answer Match 42%

Hello ,

I wonder if you could possibly help with my problem please ?

I have just recently purchased a belkin wireless g router (54mb)
Whenever i connect to the internet through the router it gives me the status of the below .....
SSID | BSSID |

amy---- 00-11-50-AE-30-64
TRACY 00-11-50-61-76-A9

Myself being amy and Tracy being the connection of someone maybe interfering with my signal ?.
Often my connection speed will drop and also go off and disapear from the status , i am forced to connect by clicking her name on her connection.
But that is the last thing i want happening.
I want to stop all this and connect to my own connection !

How would i go about stopping her from interfering with my signal and also stopping her if maybe this is happening at her end ?

I would apprechiate any help i can get !

Thanks
Amy .........
 

A:belkin wirless g router problem

add a secruity password to the router
can you post the exact model of the router - then we can look up setting an encryption

it sounds more like this is a different wireless signal

can you download and run this program
Free software to check signal strength of wireless is netstumbler 0.4.0 available for download from http://www.stumbler.net/

see what wireless networks we have in your area
 

3 more replies
Answer Match 42%

I have a Belkin Paralell to USB cable that allows me to print via my USB port through the paralell port on my Epson C88 printer. I can't seem to find the disk, and normal XP install of the device results in no printing. Anyone know how I should set up this printer to print? Use LP1 or USB0001 or what?

Thanks
 

A:Belkin Paralell Printer to USB problem

USB0001
XP instructions

http://belkin.httpsvc.vitalstreamcdn.com/belkin_vitalstream_com/support/dl/f5u002xp.pdf

Found here
http://www4.belkin.com/support/download/download.asp?download=F5U002&lang=1&mode=
 

2 more replies
Answer Match 42%

Hi,

Basically i am trying to encypt my belkin wireless adaptor and am having a few problems. On my main computer I have an orange Livebox (router) which my second computer using the belkin adaptor connects to. The orange livebox is encrytped fine. I only found out today by pure chance that my belkin adaptor is not encrypted. I have just purchased a laptop and connected to the belkin adaptor without even doing anything!!

I have tried to work out how to add an encrytpion but its really complicated with me being such a novice of wireless networks. I have had a look at the Belkin user manual and to be honest its not much help. Its probably something really simple but for the life of me i can't figure it out!!
 

A:Belkin adaptor problem.(encryption)

9 more replies
Answer Match 42%

I really want to thank to who ever can solve this situation for me. I recently bought myself a Belkin's wireless adaptor usb. First time using a wireless router. Thanks to the router; I'm able to to get connected with my ps3, my other computer's and other web design contraptions.

When I bought the USB Adaptor for my PC, it worked fine for a couple of weeks. Until Monday afternoon, when my internet began to respond slowly and until it got cut off ( disconnected, I presume). Later on yesterday, I had to uninstall it and resintall it. The same process as my Nintendo Wifi usb ( whenever I shutdown the computer, then turned it back on; I wouldn't get connectivity.) When I finished reinstalling it, I got my internet back working.

Today, the samething happened again. During the process of uninstalling and reinstalling the software. I was unable to pick up the connection. It some how got connected to my wireless network, but it wouldn't feed the internet.

I notice also, whenever I'd install it again. The wireless USB becomes " Belkin wireless adaptor USB 4" then after the next reinstallation process, number 5 and 6. Not sure if that's disrupting anything.

The belkin usb Model is F6D4050 V1

hope that helps


I can't get online that's the problem.

More replies
Answer Match 42%

Hi
I have a Belkin wireless router, l have 2 PC's connected to it and both cant get into selected sites - UK lottery being just one of many

Can anyone tell me if there are any settings in the router that can be altered to allow access to sites that l cant currently get in to

Both PC's worked fine before going wireless now both have the same problem - I have set IE settings to the minimum on everything but it makes no difference so l am assuming it has something to do with the router settings

Thanks in advance
 

A:Problem Accessing Some Sites Via Belkin

Can you check that you definitely have a connection by going to another site that you have never visited before? Sometimes it can seem like the connection is working, when actually its just getting the pages from your cache. (Although, if you posted that message from one of the PC's then you definitely have a connection).

If you are definitely connected, but you can't see some specific sites, I would struggle to help. If you don't have any software that might be interfering (pop up blockers / firewall / virus / spyware / adware / cookie blocker / any software that basically blocks a site if it doesn't like something about it), then its most likely a setting in the router. I once had that issue and someone fixed it for me, but I forgot what its called... If I remember, I'll post back.
 

2 more replies
Answer Match 42%

I installed a belkin home network system about eight month's ago. The system come with the F5D7231-4 router and wireless network card F5D7001. The first card I installed was defective. I returned it and got another one and then Everything worked. I could connect to both computers. I could share printers and files. Both computers connected to the Internet with no problem.
The computer with the card was not used for about three month's. When I restarted the system it will not connect to my other computer. The computer that is connected to the router connects to the other computer just find. Both still connect to the Internet. I uninstalled and reinstalled the drivers and software. I did a hard reset on the router and set it up.
I ran the diagnostics on the card and it shows no errors. I updated my sis LAN drivers. As far as I know the F5D7001 drivers are up to date.The problem is still there. Nothing I have done so far has made any difference. I run XP Home on both computers. Does anybody have any idea what the problem could be?

Will
 

A:Belkin wireless network problem

Did you change the workgroup name or the encryption key?
 

9 more replies
Answer Match 42%

Hey im currently having difficulty installing the belkin usb network adapter 75d7051 driver for vista im running vista home basic with a 32 bit operating system. Every time i install the driver from the belkin site it seems to install but doesnt leave an icon on my desktop. If anyone could help me it would be really appreciated
 

A:belkin wireless usb adapter problem

10 more replies