Tech Problem Aggregator

Is the current build of W10 and W10M a daily driver?

Q: Is the current build of W10 and W10M a daily driver?

It's been two years since I've done TP for mobile and I'm thinking about putting it on both my 650 and SP4. I've never done it for a pc before. Is it DD worthy?

More replies
Answer Match 55.86%

Hi guys. I recently built a new computer and it's been giving me a lot of trouble. I get a crash that says whea uncorrectable error probably twice a day.

Primarily I use the computer for gaming.

I'm not sure if this is a problem I can correct myself or if there part is bad and needs to be replaced. Oddly, when booting the screen has a green tint to it when it should be black. As soon as Windows starts the green disappears and everything looks normal. Then bam, another crash.

Any help would be greatly appreciated.

A:New build, daily BSOD

The errors are 0x124 WHEA_UNCORRECTABLE_ERROR (Windows Hardware Error Architecture)
This means that there are problems with your hardware, but this error is also caused by overclocking, faulty drivers or BIOS problems.
Please make sure your BIOS is loaded for optimal default settings, or pull the cmos battery and put it back.


STOP 0x124 Troubleshooting

Read carefully before proceeding.
   Warning
If you're overclocking your system, revert back to stock clocks now.


   Note
Test the system once the overclock is removed before continuing with the steps outlined below.

Part One: CPU Stress Test
Part Two: MemTest86+ RAM Diagnostic
Part Three: Hard Drive Diagnostics
Part Four: GPU Stress Test



ONE

 CPU TEST

Run Prime95 and/or IntelBurenTest to stress test your CPU. Prime95 - Stress Test Your CPU - Windows 10 Forums & CPU - Stress Test Using IntelBurnTest - Windows 7 Help Forums

   Warning
Your CPU temperatures will rise quickly while under this stress test. Keep a keen eye on them and abort the test if overheating occurs.



TWO

 RAM TEST

Run MemTest86+ to analyse your RAM. MemTest86+ - Test RAM - Windows 10 Forums


   Note


MemTest86+ needs to be run for at least 8 passes for conclusive results. Set it running before you go to bed and leave it overnight. We're looking forzero errors here. Even a single error will indicate RAM failure.



THREE

&... Read more

0 more replies
Answer Match 55.86%

Desperate for help; I've attached the zip file per your BSOD instructions. I also included an ntbtlog.txt that I was able to create in Safe mode today.

Here is what's happening: I have a new build that crashes daily during Windows startup. I've reinstalled multiple times with the same results. I've changed the hard drive, so it's not a drive problem. I've run Windows repair; tried Safe Mode (usually it crashes before getting into Safe Mode); memory tests, and more.

Usually, the BSODs flash so fast I can't read them; others are the "Page fault in non-paged area," or "System Volume on disk is corrupt," or "Plug and Play terminated unexpectedly."

I've gone to my motherboard's web site and updated all the driver files I can find that are newer than those on my motherboard disk. I've tried older and new display drivers.

The strange thing (to me) is that once I reinstall windows, I'm able to run okay all day with multiple reboots throughout the day. But the next morning, it always crashes with a BSOD while Windows is loading. This makes me wonder if it's a temperature-related thing with a circuit on the motherboard?

Any help would be appreciated. I'm getting very short on my 30-day return option for the equipment, so if I can't find some solution I may try another motherboard.

A:New Build - Daily BSODs

BSOD caused by nusb3hub.sys, a device driver made by NEC, update the driver
Downloads: Support & Downloads | NEC


Code:
BugCheck FC, {fffff8800337e860, 8000000002de2963, fffff8800337e3a0, 2}

Unable to load image \SystemRoot\system32\DRIVERS\nusb3hub.sys, Win32 error 0n2
*** WARNING: Unable to verify timestamp for nusb3hub.sys
*** ERROR: Module load completed but symbols could not be loaded for nusb3hub.sys
Probably caused by : nusb3hub.sys ( nusb3hub+f074 )

5 more replies
Answer Match 55.44%

What`s the number of today`s official W7 build? Is it still 7600.16385? Has someone already installed "officially bought" W7?
P.S. Sorry 4 my weak Englash.

A:What is current W7 build number?

Why would it change?

9 more replies
Answer Match 55.44%

About five months ago I decided to invest in a custom build. It ran fine for the first couple months. After that I began to have the occasional BSOD with increasing frequency. Strangely enough, they seemed to occur regularly for about a week and would then stop only to start up again a week or so later. Now, the problem has escalated to nearly every night.

I do game often but have only had one crash while doing so. The rest occur randomly while watching a video online or while the computer is on sleep.

Unfortunately, I do not know enough to pinpoint the exact problem. From what I've seen with other threads, "ntoskrnl.exe" often takes the blame for the crash but isn't necessarily the cause. Rather than risk causing more damage, I thought I'd seek advice from those more knowledgeable than myself. Any help is greatly appreciated.

I have attached the SF Diagnostic Tool .zip file from my crash. Please let me know if there is any other information I have forgotten to include.

Custom Build Specs (as purchased from Newegg):
ASUS GRYPHON Z87 LGA 1150 Intel Z87 HDMI SATA 6Gb/s USB 3.0 uATX Intel Motherboard
Intel Core i5-4670K Haswell 3.4GHz LGA 1150 84W Quad-Core Desktop Processor Intel HD Graphics BX80646I54670K
EVGA 02G-P4-2763-KR GeForce GTX 760 2GB 256-bit GDDR5 PCI Express 3.0 SLI Support w/ EVGA ACX Cooler Video Card
G.SKILL Ripjaws X Series 8GB (2 x 4GB) 240-Pin DDR3 SDRAM DDR3 2133 (PC3 17000) Desktop Memory Model F3-2133C10D-8GXM

CORSAIR ... Read more

A:Daily BSOD with Custom Build

Hi nickiek.

A stop 0x124 is some sort of hardware issue.

Are you overclocking? As you are getting BSODs, you should stop overclocking and run all the hardware components like CPU, GPU and RAM to their default settings.

Check if the Power Supply Unit (PSU) supplying adequate power to the computer or not.
eXtreme Power Supply Calculator
Also let us know the wattage of the PSU.

Is the computer hot? Report us the heat of the computer after a couple of hours of your normal usage. Upload a screenshot of the summery tab of Speccy. Alternatively, you can publish a Speccy snapshot too: Speccy - Publish Snapshot of your System Specs .

Test your RAM modules for possible errors.
How to Test and Diagnose RAM Issues with Memtest86+
Run memtest for at least 8 passes, preferably overnight.
If it start showing errors/red lines, stop testing. A single error is enough to determine that something is going bad there.

Stress test the Graphics Card using Furmark.
Video Card - Stress Test with Furmark

Stress test the CPU.
Hardware - Stress Test With Prime95

Let us know the results.
__________________________________________________________________________________________

Code:
*******************************************************************************
* *
* Bugcheck Analysis *
* ... Read more

1 more replies
Answer Match 55.44%

Hi all, I've read as much as I can to try and solve my BSODs but no joy so far so I thought I'd post here.

I'm getting them at random times, often when I'm not putting the computer under load or doing any one thing I can find to trigger it. Here are my specs.

AMD Phenom II X4 965 BE (quad core @ 3.4GHz)
4GB Corsair RAM
Asus Mobo
EVGA GFX460 1GB (Nvidia)
Samsung Spinpoint 1TB HDD (sata)

I built the computer and installed windows myself.

I'm running Windows 7 Home Premium x64 Full OEM. I've attached what's asked for, so hopefully someone can point me in the right direction. Here's hoping!

Thanks in advance

A:New build, AMD based, almost daily BSOD

Hello,

See if you can uninstall the nVidia Stereoscopic driver:
Code:
Event[1923]:
Log Name: System
Source: Service Control Manager
Date: 2011-03-12T14:47:10.670
Event ID: 7000
Task: N/A
Level: Error
Opcode: N/A
Keyword: Classic
User: N/A
User Name: N/A
Computer: Adam-PC
Description:
The NVIDIA Stereoscopic 3D Driver Service service failed to start due to the following error:
NVIDIA Stereoscopic 3D Driver Service is not a valid Win32 application.
Install SP1: Learn how to install Windows 7 Service Pack 1 (SP1)

I notice the clock is (or was) seriously off:
Code:
Original Install Date: 08/02/2011, 22:55:19
See this log:
Code:
Event[1723]:
Log Name: System
Source: Microsoft-Windows-Time-Service
Date: 2011-03-13T01:00:18.006
Event ID: 34
Task: N/A
Level: Error
Opcode: Info
Keyword: N/A
User: S-1-5-19
User Name: NT AUTHORITY\LOCAL SERVICE
Computer: Adam-PC
Description:
The time service has detected that the system time needs to be changed by -86294 seconds. The time service will not change the system time by more than 54000 seconds. Verify that your time and time zone are correct, and that the time source time.windows.com,0x9 (ntp.m|0x9|0.0.0.0:123->207.46.232.182:123) is working properly.
Do as the report says; make sure the time is correct in the BIOS as well as in Windows.

Also, some hardware diagnostics are in order. Start with the three Prime95 tests: http://www.sevenforums.com/tutorials...t-prime95... Read more

7 more replies
Answer Match 55.44%

Hello,

I apologize in advance for being new but I will follow instruction if someone can just help point me in the right direction

I have a custom built computer that has been getting random BSOD. They happen everyday. I can boot my computer, then randomly in the first hour it will usually crash. After the crash, the computer works just fine until after I turn it off. I can run it for days without another BSOD but as soon as I turn it off and boot back up, I will inevitably get another BSOD at a random time soon after. I've included my specs and ran the DM Log (which is included as well). I also have a crash dump analysis from WhoCrashed which I will copy/paste here also. Please let me know if there is anything else I need to include and what I can do to resolve this issue.

Thanks in advance!!

Additionally, I have no idea why WhoCrashed is showing my Windows version as Windows XP Service Pack 3, 5.1, build: 2600. I most definitely have Windows 7 Home Edition 64-bit.

System Information (local)
--------------------------------------------------------------------------------

Computer name: GAMING-PC
Windows version: Windows XP Service Pack 3, 5.1, build: 2600
Windows dir: C:\Windows
Hardware: Z97X-Gaming 7, Gigabyte Technology Co., Ltd.
CPU: GenuineIntel Intel(R) Core(TM) i7-4790K CPU @ 4.00GHz Intel586, level: 6
8 logical processors, active mask: 255
RAM: 17018142720 bytes total




----------------------------------------------------------------... Read more

More replies
Answer Match 55.02%

I would like to take the copy of Win7 Ultimate I use now, and install it on a new PC build I will be getting in a couple of weeks.

As soon as I can, I will get a new copy of Win8.1, but I am wondering if I can use the old OS on a new PC, before the 30 days (before activation) is up, and install the new OS on it before then, as an upgrade or full version?

I'm assuming this can be done, as I had a housemate move in years ago who didn't have an OS (because his WinXP installed fatally messed up during updating) and so he asked for my WinXP disc at the time and kept reinstalling it every month - he just didn't "activate" it. He later got his own copy.

I would assume if it's possible, then it's not legal, but then I'm suggesting a temporary measure and won't stick with it.

Anyone know?

A:Using my current copy of Win7 on a new PC build

Hello Foebane,

You will need to install a retail copy of Windows on the new PC, but yeah it's perfectly legal to do so as a 30 day trial without activating.

Personally, I would recommend to clean install Windows 8.1 instead of upgrading from Windows 7. This way you won't have to worry about any potential issues from an upgrade.

2 more replies
Answer Match 55.02%

My mobo recently died, more precisely storage controller.
I have a P5WDH Deluxe and was getting bsod on boot.
Error message referred to virus, hdd or hdd controller issues (x...7B,).
So I switched my system drive to boot from the jmicron controller on the board and it booted up fine.
So I am considering getting a new mobo and using all my existing components.
Can I install my existing system drive in this new build as is? Or...?
I would like to do this as it has all my settings and apps on it.
Any suggetions/recommendations or if this is not possible what are my options?
Thanks in advance for any help and advice.
 

A:Use current system drive in new build

Chipset drivers will be the twist, but that can be overcome...

You'll probably have to revalidate your Windows installation by phone...

...but I don't know why you couldn't.

Other opinions and experience will most certainly vary.
 

3 more replies
Answer Match 55.02%

Hello,

Microsoft's Level 2 people are going to upgrade my 8.1 Pro system to Windows 10 Pro. There seems to be a lot of versions/builds floating around out there. I have several questions may be someone(s) can answer

1. Does anyone know the most current version/build that I should be getting?

2. I have an SSD and used the SYSPREP process which was written up by @kali to have my Documents folder put on a non-SSD device. Will this process still work and can MS do it using whatever version of Windows that they download? To do the sysprep for 8.1 required having the distribution media which I had for 8.1 but do not for 10.

3. Is there additional maintenance that needs to be put on

4, What else should I be aware of?

I am only doing this upgrade because of a need to solve a problem on my existing 8.1 system. Apparently there is no repair capabilities for 8.1 so a clean install would need to be done (or so I've been told). Rather than go through this again it seems like the upgrade is a better choice (I think). However, it seems that even after 1+ years there are still a lot of problems with Win 10. I would welcome some opinions on that.

This PC is relatively new and is used for trading and I really do not want to mess with it too much if there is a risk.
Note:

This is a different PC than the one in my other post in this same thread.
Thank you,

Frank

A:Windows 10 Pro current build number

1. Mine is Version 1607 Build 14393.105. Actually, the Home version will be the same number. And both versions are available as either 32-bit or 64-bit.

If the problems with Win8.1 are severe Upgrading to a newer version may not solve them, may even make them worse.

0 more replies
Answer Match 55.02%

I have some cash to build a new gaming rig. My current rig is just about three years old right now. I mainly play WoW, but am on the lookout for potential new games when they come out, i.e. Warhammer or whatever else may be a viable alternate to WoW.
I am trying to decide whether to spend $3300 on building a new gaming rig right now with a quad core (trying to be future proof), or just upgrade the video card and monitor in my current rig. My current rig plays WoW fine, but chugged significantly when I played LOTRO. I had to turn the graphics down to medium to get somewhat smooth performance.

Please let me know your thoughts.

Here are my current gaming rig specs:

-Mobo: ASUS P5AD2 Deluxe
-CPU: Intel 3.4GHz, 800FSB with HT
-RAM: 3GB of matched Corsair: 1GB of DDR2 PC5400 chips and 2GB of PC6400 running in dual channel mode. TWIN2X2048-6400C4
-HD: dual WD 74GB 10,000 RPM Raptors in RAID 0 config using SATA
-Video: eVGA GeForce 6800 GT PCI Express card with 256MB memory
-Monitor: 19" ViewSonic VP210b LCD with 12ms response time
-Sound: Creative Blaster X-Fi Fatal1ty FPS

Besides the video card, I think the next weakest link is the CPU. Is a P4 3.4GHz still adequate for gaming, or will it be too weak for upcoming games?

Thanks for all your feedback.
 

A:To build new or upgrade current gaming rig

In general, if you're going to spend more than $300 in upgrades, it's better to get a newer system.
 

11 more replies
Answer Match 55.02%

I'm asking as I'm going to install it on my PC. I tried Windows XP Professional 64-bit but it seems it's not entirely compatible with my Core i7 system, and I know Vista is slower than Windows 7, so I'm wondering currently which is the best build of Windows 7 to use.

Thanks.

A:Current, most stable build of Windows 7, is?

7137

9 more replies
Answer Match 54.18%

Anyone know of a link to show the current build/version of IE9 beta?

Or is there a beta included version of Windows/MS update? I remember a box to click on in XP but can't find it in '7.

More replies
Answer Match 54.18%

Motherboard:
ASRock 970DE3/U3S3 AM3+
http://www.newegg.com/Product/Product.aspx?Item=N82E16813157305

Case:
10-Bay ATX Mid Tower Computer Case
http://www.geeks.com/details.asp?invtid=T650&cat=CAS

Processor:
AMD Sempron 145 Sargas 2.8GHz
http://www.newegg.com/Product/Product.aspx?Item=N82E16819103888

Will this motherboard fit with the case?
Also are this MB and CPU even compatible?
 

A:Solved: Current Motherboard build for a colleague......Will it fit together?

16 more replies
Answer Match 54.18%

Hey guys

I was wondering how you would go about installing an older build of windows 7 over a later build

Im trying to install 7127 over 7229 but not getting far as I can't find any relevant information on google

Have to downgrade seeing as punkbuster refuses to work with 7229 no matter what I do

Any help is appreciated

A:Installing an older build over current installation

Boot from the 7127 DVD and clean install to the same partition 7229 is on. Do not format the hard drive and your existing files will be saved in Windows.old folder.

6 more replies
Answer Match 54.18%

Hi.

We have several function rooms containing a Windows 8.1 PC which lots of people use throughout the day.

When people use these machines, we want them to have full access so they can download and install the apps they wish to use.

This obviously makes the PC's very cluttered, but it is necessary.

What I would like, is for the PC's to load to a clean/fresh image on a daily or even weekly basis.

How am I best doing this? Any good utilities or tools to use. Want to make it as automatic as possible.

A:Windows 8.1 to refresh daily to clean build status???

If you had a local image on a sever that the PC could grab the image from, then it would be possible.

You would need scripts for having the PC download the image, reinstall, finish setup, and be ready for the next morning. It certainly isn't an easy task.

1 more replies
Answer Match 49.56%

Hi!

So, my soundcard is the VIA 3059 Series Audio Controller. I'm using C-Media right now, but want to know if there are better drivers than mine. Version is 5.12 in case there's an update but I want to hear about alternatives as well (for instance, I had a P4 HP Pavillion whose sound controller (ALC something can't remember now) would support both Realtek ACī97 and VIA Vinyl drivers.
 

More replies
Answer Match 49.14%

I just bought a LIVING BOOKS software for my son and I installed it per the pop up instructions on the screen...but when I try to run/play it I get a "living books window" that states "Current display driver palette too small" What does this mean and how do I fix it?
 

A:Current driver display too small...

7 more replies
Answer Match 49.14%

Hey guys, Recently got my new computer, and it is amazing! Only problem is that 2 or 3 times a day i get a BSOD...

I checked the Minidump files and it's saying something about VISTA_DRIVER_FAULT and ntoskrnl.exe driver fault.

This is what the Dump File reads:


Code:

Loading Dump File [C:\Users\Nico\Desktop\100210-21122-01.dmp]
Mini Kernel Dump File: Only registers and stack trace are available

Symbol search path is: *** Invalid ***
****************************************************************************
* Symbol loading may be unreliable without a symbol search path. *
* Use .symfix to have the debugger choose a symbol path. *
* After setting your symbol path, use .reload to refresh symbol locations. *
****************************************************************************
Executable search path is:
*********************************************************************
* Symbols can not be loaded because symbol path is not initialized. *
* *
* The Symbol Path can be set by: *
* using the _NT_SYMBOL_PATH environment variable. *
* using the -y <symbol_path> argument when starting the debugger. *
* using .sympath and .sympath+ *
*********************************************************************
Unable to load image \SystemRoot\system32\ntoskrnl.exe, Win32 error 0... Read more

A:Daily BSOD, ntoskrnl.exe driver fault?

Tell us when you get these BSODs, i.e., randomly or are you doing something specific at the time.

You have errors 0x3B and two 0xA but they only cite Windows OS drivers and these are usually too general to be of much diagnostic help.

By the way, I noticed your system hardware (nice set-up; love to hear your feed back on that 635 processor) and you are running 6 gigs of RAM. Try running with just 4 gigs. Do you gain stability?
 

7 more replies
Answer Match 49.14%

Hello,

My machine is rebooting on a daily basis mostly when I'm not using it. I leave my machine on all the time. When I cick on send the error to MS I get a MS webpage that notes that my machine has a Driver conflict. The MS website does not really help me diagnose it though. Anyone have any suggestions on how I should proceed in diagnosing this problem? http://images.techguy.org/smilies/confused.gif
TIA

-juan
 

A:Driver error causing daily reboot

7 more replies
Answer Match 49.14%

I had a problem with audio software a few days ago, though a dell technician was able to fix it by remotely controlling my computer. Two days later however my computer started crashing almost every time i use it. Please help me.

A:BSOD Driver IRQL LESS OR NOT EQUAL, happens daily

http://www.sevenforums.com/crashes-d...tructions.html

2 more replies
Answer Match 49.14%

Hey guys, Recently got my new computer, and it is amazing! Only problem is that 2 or 3 times a day i get a BSOD...

I checked the Minidump files and it's saying something about VISTA_DRIVER_FAULT and ntoskrnl.exe driver fault.

This is what the Dump File reads:


Code:
Loading Dump File [C:\Users\Nico\Desktop\100210-21122-01.dmp]
Mini Kernel Dump File: Only registers and stack trace are available

Symbol search path is: *** Invalid ***
****************************************************************************
* Symbol loading may be unreliable without a symbol search path. *
* Use .symfix to have the debugger choose a symbol path. *
* After setting your symbol path, use .reload to refresh symbol locations. *
****************************************************************************
Executable search path is:
*********************************************************************
* Symbols can not be loaded because symbol path is not initialized. *
* *
* The Symbol Path can be set by: *
* using the _NT_SYMBOL_PATH environment variable. *
* using the -y <symbol_path> argument when starting the debugger. *
* using .sympath and .sympath+ *
*********************************************************************
Unable to load image \SystemRoot\system32\ntoskrnl.... Read more

A:Daily BSOD, ntoskrnl.exe driver fault?

  
Quote: Originally Posted by SunDown


Hey guys, Recently got my new computer, and it is amazing! Only problem is that 2 or 3 times a day i get a BSOD...

I checked the Minidump files and it's saying something about VISTA_DRIVER_FAULT and ntoskrnl.exe driver fault.

This is what the Dump File reads:


Code:
Loading Dump File [C:\Users\Nico\Desktop\100210-21122-01.dmp]
Mini Kernel Dump File: Only registers and stack trace are available

Symbol search path is: *** Invalid ***
****************************************************************************
* Symbol loading may be unreliable without a symbol search path. *
* Use .symfix to have the debugger choose a symbol path. *
* After setting your symbol path, use .reload to refresh symbol locations. *
****************************************************************************
Executable search path is:
*********************************************************************
* Symbols can not be loaded because symbol path is not initialized. *
* *
* The Symbol Path can be set by: *
* using the _NT_SYMBOL_PATH environment variable. *
* using the -y <symbol_path> argument when starting the debugger. *
* using .sympath and .sympath+ *
*********************************************************************
Un... Read more

2 more replies
Answer Match 49.14%

Hello, I've been getting multiple driver crash per day and got a BSOD once.

I've been using the same Nvidia driver since January, but for some reason it started crashing for the past week. I didn't update anything nor change my hardware. No overclock.

You can find my system specs here:
http://www.sevenforums.com/members/birkhoff.html

A:Multiple Daily Driver Crash and BSOD

Hi Birkhoff.

Update the display driver to the latest WHQL from Drivers - Download NVIDIA Drivers.

When done, stress test the Graphics Card using Furmark. Video Card - Stress Test with Furmark
Take a screenshot of the furmark window before closing it. Upload the screenshot for us. Also let us know if you have experienced any crash/BSOD and/or artifacts during the test. Also let us for any further BSOD.
____________________________________________

Code:
BugCheck 117, {fffffa80071db4e0, fffff88004f4b81c, 0, 0}

*** WARNING: Unable to verify timestamp for nvlddmkm.sys
*** ERROR: Module load completed but symbols could not be loaded for nvlddmkm.sys
Probably caused by : nvlddmkm.sys ( nvlddmkm+13e81c )

Followup: MachineOwner
---------

2: kd> !analyze -v
*******************************************************************************
* *
* Bugcheck Analysis *
* *
*******************************************************************************

VIDEO_TDR_TIMEOUT_DETECTED (117)
The display driver failed to respond in timely fashion.
(This code can never be used for a real bugcheck.)
Arguments:
Arg1: fffffa80071db4e0, Optional pointer to internal TDR recovery context (TDR_RECOVERY_CONTEXT).
Arg2: fffff88004f4b81c, The pointer into responsible device driver module (e.... Read more

9 more replies
Answer Match 48.72%

I have a machine here that seems to be BSODing on a (roughly) daily basis at random. There seem to be a couple different crashes occurring, but they're likely related. It seems to happen more often when the machine is coming out of sleep mode, but is intermittent enough that it's tough to determine. I've already tried using the Driver Verifier as seen in my minidumps, but can't seem to nail it down. This is a new Windows install, as I was seeing this issue on the previous install.

Ran memtest86 overnight, Dell's BIOS diags, and Prime 95/FurMark for 4-8 hours all with no faults.

I am happy to provide more information as required.

Edit: This machine is the same as the one in my profile, except we've replaced the HDD with a Samsung Evo 850, and it's running 32GB RAM.

More replies
Answer Match 48.72%

We have a few Dell Latitude E5570's in our organization and 1 user is having issues with the Intel HD 520 Video Driver restarting daily.  The screen will pause then both monitors will quickly go to power save then the video driver starts back up.  I have tried all drivers available on Dells site and have tried Intels drivers, but nothing seems to stop the issue.  I can replicate the issue on all of our E5570's so it is not a hardware issue.  Any advice would be greatly appreciated.  Thank you.

More replies
Answer Match 47.88%

I'm surprised that I am not finding a thread on this issue already.
Evidently something that changed in a recent build has caused both Facebook apps to crash.
When you launch the app it closes just after the window pops up.
It's kind of a bummer because when you get a notification and it opens the app, it just crashes.
The only way to use Facebook at the moment is with the browser.
I hope they get this fixed. Maybe the app needs to be updated now but to have an app quit working with an OS build update is not good.
On the Windows Store the ratings/feedback is flooded with users all experiencing this issue.

More replies
Answer Match 47.88%

I made a post earlier looking to see if my laptop would be okay to run Windows 7. I posted some of the builds I had at my disposal which a moderator then closed the post and called me a pirate basically.

I am not a pirate and I am against pirating software, I was unaware of those builds being considered pirated.

So what Windows 7 builds are available ( the latest ) that I can use right now.
 

A:Windows 7, most current "legal" build?

6 more replies
Answer Match 47.88%

Is there a version out that is available for download that is not considered to be warez. I know I am late on testing it but I finally wanted to install it and give it a go.

Thanks
 

A:Windows 7, most current "legal" build?

Windows 7 Release Candidate: Download instructions is legal, no quotes needed.
 

1 more replies
Answer Match 47.46%

It would be great if HP included some instructions in their update section to walk us through, step by step, how to install a new driver when the previous one must first be uninstalled. Most updates are just click and download. Nothing else required.  But some of us aren't all that comfortable uninstalling drivers and don't know where to begin.

A:Intel Bluetooth Driver update--how to uninstall current driv...

Hi, Thank you for posting. You should not uninstall previous driver prior to updating new one. In Windows 10 you can install updates via Windows Update or Device Manager (preffered method). Here is how >> http://support.hp.com/us-en/document/c03330139 For non-critical, not so important and other updates, you can also use HP Support Assistant (HPSA) >> http://support.hp.com/us-en/document/c03467905In HPSA, please skip BIOS/UEFI updates.  Hope this helps. Feel free to reply back if something is not clear.

4 more replies
Answer Match 47.46%

My laptop always got an BSOD Driver power state failure everyday.
if my laptop gets a BSOD, it will get chain BSOD for 10-40 minutes. I already reinstall the windows but it didn't resolve the problem, I already update my Windows to SP1 but it didn't resolve the problem too.
I already update the drivers especially the Graphic driver for Intel HD and Nvidia but its still same.
While in gaming (With Nvidia) my laptop never get a BSOD, i'm little confused because if I playing game with Intel HD (Forgot to set the GPU game with Nvidia) it will get a BSOD few minute after the game closed.
Even if my laptop idle for 1-3 Hours it will get the BSOD too.

After my laptop create the dumb file and successful created it my laptop won't restart and will stuck at BSOD Screen so I must hold the power button to turn it off.

Please Help my laptop is suffering this BSOD for almost half a year.


Here is my Laptop Spec:Model Acer Aspire V3-471G
Intel Core i5-3210M 2.5GHz
Nvidia GeForce GT 630M w/ 2GB Dedicated VRAM
4 GB DDR3 Ram
Intel HD Graphics 4000
I'm Appreciate any Replies and Help and Sorry for my bad English.

A:Driver Power State Failure Daily Strikes (Not in Gaming w/ Nvidia)

It appears that the BSOD is occurring while switching graphics between the onboard and dedicated. It happens with nvidia optimus technology, very frequently.

I dont know exactly what to do here, but I am asking for some help from the GPU experts.

But we are seeing SPTD as failing, too; and that is the most frequent BSOD causer.

Daemon Tools, Alcohol 120% and Power Archiver Pro uses SCSI Pass Through Direct (SPTD), which is a well known BSOD causer. Uninstall Daemon Tools at first. Then download SPTD standalone installer from Disk-Tools.com, and execute the downloaded file as guided below :
Double click to open it.
Click this button only:

If it is grayed out, as in the picture, there is no more SPTD in your system, and you just close the window.
__________________________________________________________________________________

Code:
0: kd> !irp fffffa800484ac60
Irp is active with 4 stacks 2 is current (= 0xfffffa800484ad78)
No Mdl: No System Buffer: Thread 00000000: Irp stack trace.
cmd flg cl Device File Completion-Context
[ 0, 0] 0 0 00000000 00000000 00000000-00000000

Args: 00000000 00000000 00000000 00000000
>[ 16, 2] 0 e1 fffffa8005194040 00000000 fffff880085e0f18-fffffa80099fa780 Success Error Cancel pending
*** WARNING: Unable to verify timestamp for sptd.sys
*** ERROR: Module load completed but symbols could not be loaded for sptd.sys
\Driver\ACPI nvlddmkm
Args: 00000000 00000001 0000000... Read more

5 more replies
Answer Match 47.04%

I recently purchased a used HP 2000 Notebook and performed a fresh install of windows 7 to wipe it. I did not test Aero prior to doing a fresh install but considering it came from the factory with Windows 7 on it I figured it should be able to support Aero. Is this not the case?
This is the message that appears when I try to troubleshoot my problem with Aero.

"The current video card may support Aero with a driver that is compliant with the Windows Display Driver Model (WDDM). Contact the manufacturer of your computer or video card for a WDDM-compatible driver."

I tried searching for solutions via google but nothing I have tried has worked for me. So far I have tried the following:

-Troubleshooting
-Windows updates
-Updating my driver
-Restarting Device manager

A:Current video card may support Aero w/ a driver compliant w/ WDDM

Hi Welcome to Seven Forums ... You do not state which Graphics Card you have .. Also the Model Number you have given is not complete there are some letters missing .. The message you got from Windows means you should go to the Manufactures Website for the Driver ...

3 more replies
Answer Match 46.2%

hi help me please.

Problem signature
Problem Event Name: BlueScreen
OS Version: 6.1.7600.2.0.0.256.1
Locale ID: 1033
Extra information about the problem
BCCode: 1000007e
BCP1: FFFFFFFFC0000005
BCP2: FFFFF80002F6B93E
BCP3: FFFFF88002FF5A48
BCP4: FFFFF88002FF52B0
OS Version: 6_1_7600
Service Pack: 0_0
Product: 256_1

A:Daily Daily Blue Screens on win7 64bit

  
Quote: Originally Posted by freeangel


hi help me please.

Problem signature
Problem Event Name: BlueScreen
OS Version: 6.1.7600.2.0.0.256.1
Locale ID: 1033
Extra information about the problem
BCCode: 1000007e
BCP1: FFFFFFFFC0000005
BCP2: FFFFF80002F6B93E
BCP3: FFFFF88002FF5A48
BCP4: FFFFF88002FF52B0
OS Version: 6_1_7600
Service Pack: 0_0
Product: 256_1



Freeangel hi and welcome
Most of these point to a memory exception. caused by several different thins. Your video driver, USBPORT, and others. to get a handle on this we should first verify you memory. Everything should be set to default no over clocking

Download a copy of Memtest86 and burn the ISO to a CD using Iso Recorder or another ISO burning program. Boot from the CD, and leave it running for at least 5 or 6 passes.

let us know the results
Ken

8 more replies
Answer Match 45.78%

IF you compare today both versions, which do one do you think is best?

A:WM 6.5 vs W10M

For me:
Functionality: 6.5.x
UX (unskinned): WM10.x
Please join the site so you can reply in this thread. See this link for instructions on how to join Windows Central.

2 more replies
Answer Match 45.36%

Does anyone know how to create an app using windows app studio for phones. I am trying to create one with the pivot style but don't know how to. I am trying to use a url so that the app pulls the info. Is this possible? I have been able to make one with the web host but that only creates web wrap apps. If anyone has knowledge on how to make a pivot style app using windows app studio please post it here I would appreciate it.

More replies
Answer Match 45.36%

so I haven't used W10M in a while. How is the Uber app? Does it have the spilt ride feature? Can I share my route? Are there any features missing from Android or IOS?
Posted via the Windows Central App for Android

More replies
Answer Match 45.36%

There's a problem I can't understand. I downloaded four GBA emulators(VBA8, VBA10, Purple Cherry X, etc.) on my L640. I started a game Pokemon Emerald and was shocked. In every emu sound is distorted and makes headaches, in VBA8 fps is lower than 45fps, in VBA10 and Purple Cherry X - lower than 40 and 30 fps. By the way, VBA10 makes phone really hot, although fps is lower, sound is even worse quality and app is made for W10M so all this makes no sense, because VB8 on W10M works miles better, but it's still unacceptable. Why? Because my old PSP with 333MHz processor and 64 MB RAM emulated GBA games almost perfectly.
Okay, there could be some reasons like bad coding and small number of WP/W10M users, but, come on, even GBC games (like Pokemon Crystal) on those WP/W10M GBA emulators are not emulating great, sound is distorted too, but, at least, are listenable. But no excuses, because I emulated pokemon crystal on my iPod Nano 1st gen. which has 80MHz cpu and there is no sound distortion at all... All this just makes no sense.

A:Why emulation on W10M/WP is so bad?

It's simply because development is lacking. I hope that with the ability to port Win32 apps to the Store and all that, we get to see VBA-M soon enough.
Sent from mTalk

3 more replies
Answer Match 44.94%

I just bought a L650 and I notice that I'm not getting messages on SP4 from the Lumia. But I do get them from my Note 5. Any answers?

More replies
Answer Match 44.94%

Cortana for AU changes few things. From that in setting auto language select option is available. Australia,India,USA,UK Some country available. Currently I am using India region. 1 ) If I want cortana USA can I must download language for that? 2 )what's the difference between cortana of these region. ( any extra features on cortana of selected region from above ) Waiting for answer guys. If u use cortana daily please answer above.

More replies
Answer Match 44.94%

Hi
is it possible to customize the outlook app, with different colors, for the different email accts?
i don't see a way, but one never knows.
i don't want all my email accts, with the same color.
different colors would make identifying emails accts. much easier.
thx!

More replies
Answer Match 44.94%

Recently I do hard reset with Lumia 640. Store app still in old version and store not showing for store app. Any buddy please give store link so that store app get manually updated.

A:W10m store link please

Happened to me too in anniversary update for mobile.. Its not yet released for public so i had to set it to fast ring and then wait for few hours then got the updates. I do this each time i format my phone on my Lumia 640xl.

2 more replies
Answer Match 44.94%

I have a lumia 640 lte and I'm in the insiders programm (slow ring). Can't find the way to set a static ip. I really need this feature, any tips?
Thanks!

A:Is static ip suported in w10m?

See if this workaround solves your problem How to use Static IP in your Windows 10 Mobile! ? GIZMO NATION

1 more replies
Answer Match 44.94%

Wife's 1520 on the latest rs2 fast ring updated. Now, edge opens then immediately closes. Anyone know of any fixes?

More replies
Answer Match 44.94%

Cortana for AU changes few things. From that in setting auto language select option is available. Australia,India,USA,UK Some country available. Currently I am using India region. 1 ) If I want cortana USA can I must download language for that? 2 )what's the difference between cortana of these region. ( any extra features on cortana of selected region from above ) Waiting for answer guys. If u use cortana daily please answer above.

A:Cortana w10m AU question

Yes, you must download the relevant speech and language packs for each region
Difference would be each offers results closer to their own region rather than your current one - that's my opinion

more replies
Answer Match 44.94%

Hello to all I wanted to ask around to anybody who might know if Living Images is still a feature on W10M. I am not sure if I have missed anything about it, and I haven't heard much since last year when it showed up in some developer preview versions on certain phone models. I am really hoping it was not taken away from the Windows Mobile platform, as it was an awesome feature that Microsoft started (and which Apple stole). Does anybody know of it still exists on Windows 10 Mobile? Thanks for any information.

More replies
Answer Match 44.94%

Do you guys have issues with some websites loading on EDGE on W10M? Some websites show a blank white screen. When i go to Tomshardware.com, it says FORBIDDEN. But the websites loads just fine on UC browser. What gives?

A:Microsoft Edge on W10M

Originally Posted by slickxsparkie Do you guys have issues with some websites loading on EDGE on W10M? Some websites show a blank white screen. When i go to Tomshardware.com, it says FORBIDDEN. But the websites loads just fine on UC browser. What gives? in settings, clean cache and allow all cookies, then reboot your device

1 more replies
Answer Match 44.94%

Does anyone know of a Fantasy football app for Windows 10 Mobile? The espn fantasy football app and the NFL Fantasy football app in the windows store are not working on my Lumia 950 build 14393. I was wondering if anyone is experiencing this or if someone has found another/ different app.

More replies
Answer Match 44.94%

I've downloaded one, but I wanted to know what's the best app out there. The store itself is not of much help.

More replies
Answer Match 44.1%

My Lumia 640 with Windows 10 (previously 1511, now 1607; I'm on Release Preview) doesn't get past Uber app version 2.5.x, but WC reports (repeatedly) on the Uber app being 3.2.x: http://www.windowscentral.com/uber-update-makes-it-easier-book-cab?_ga=1.94882716.1280883874.1469892291 .
I've tried to reinstall, uninstall-restart-install, and similar several times, I've also tried direct links to the Windows 10 app in the store, but apparently I cannot get higher than version 2.5.1. Are people using the 3.2 version? How did you get it? Any thoughts on how I can update my phone to rock the latest version?
Thoughts would be most appreciated!

A:How can I get the latest (3.2.x) version of Uber app for W10M?

Is your Store app up to date? Sometimes the Store app can cause issues. How is your connection when you try it?

3 more replies
Answer Match 44.1%

Hello -
Yesterday our work firewall was replaced with a Fortinet device. It has been configured as an IPsec VPN. The FortiClient app for W10M appears to only have settings for a SSL-VPN.
Any ideas on how I can access our network from my phone?

A:Fortinet Firewall Access with W10M

You might have to get in touch with your work IT department to see what your options are.

1 more replies
Answer Match 44.1%

I'm using windows 10 both on my PC and phone, a lumia 640. I'm not in the insider program.
Although edge on my PC syncs and gets my favorites from my phone, my phone cannot sync and get favorites from my PC in any reliable way.
Sometimes it takes days or it fails to do so entirely.
Is there a way to force edge on my phone to sync favorites manually?

More replies
Answer Match 44.1%

Hey guys. Just wanted to see if anyone else has problems with updating their apps on RS2? Every app I try to update just says "Error, tap to see details" and an obscure error code.

A:W10m RS2, Unable to update apps.

Originally Posted by Giddora Hey guys. Just wanted to see if anyone else has problems with updating their apps on RS2? Every app I try to update just says "Error, tap to see details" and an obscure error code. first, make a soft reset

1 more replies
Answer Match 44.1%

Am I doing something wrong or is twitter out of the people hub now? Can't get it to synch since the app was updated?

More replies
Answer Match 43.68%

Does anyone know how to stream live sports links on w10m? I'm trying to find a app which you can add a link and it plays the stream. Alot of the streams don't play on the edge browser because there is no flash adobe. I have used kodi for the windows 10 pc/ android tablet, but I'm trying to find something that works similar for windows 10 mobile.

More replies
Answer Match 43.68%

My mom buyed an lumia 640lte and updated it to w10m, now she have all of her contacts mixed ex: Jhon doe to dr marcus doe.

More replies
Answer Match 43.68%

Hi it looks like Facebook, twitter, and LinkedIn all gone from w10. If I roll back to wp8 will I get them back? Thanks

More replies
Answer Match 43.68%

Hello,
I've been experiencing multiple bluescreens daily and what's odd about them is they occur randomly while using many programs; however, I have noticed that they occur more frequently directly after opening a new tab, loading a new site or running a game (StarCraft II).
Looking through Event Viewer. I see a list of warnings and errors immediately prior to the BSOD. In chronological order:

9:07:18 PM CRITICAL- "The system has rebooted without cleanly shutting down first. This error could be caused if the system stopped responding, crashed, or lost power unexpectedly."

9:07:28 PM WARNING- "The driver \Driver\WUDFRd failed to load for the device USB\VID_0483&PID_2016\5&249af6f9&0&2."

9:07:42 PM ERROR- "The previous system shutdown at 9:05:49 PM on &#8206;7/&#8206;13/&#8206;2011 was unexpected."

9:07:44 PM ERROR- "The computer has rebooted from a bugcheck. The bugcheck was: 0x0000000a (0x0000099e0000007e, 0x0000000000000002, 0x0000000000000001, 0xfffff80002a92885). A dump was saved in: C:\Windows\MEMORY.DMP. Report Id: 071311-32869-01."

9:07:47 PM ERROR- "Audit events have been dropped by the transport. 0"

I also get this warning quite often:
"The maximum file size for session "ReadyBoot" has been reached. As a result, events might be lost (not logged) to file "C:\Windows\Prefetch\ReadyBoot\ReadyBoot.etl". The maximum files size is currently set to 20971520 ... Read more

A:Multiple BSOD daily "\Driver\WUDFRd failed to load for the device"

10 more replies
Answer Match 43.26%

Lot of people say the big problem the app gap. But if you can run android emulator on your phone that isn't problem. So I would like know that is possible? Unfortunatelly I don't know convert app but I hope anybody can help for me.

A:Android emulator convert to W10M with Desktop App Converter

Hi and welcome to Windows Central. There is no Android emulator for Windows 10 Mobile. Project Astoria was cancelled by Microsoft quite a while ago. Microsoft officially cancels 'Project Astoria' plans for porting Android apps to Windows 10 Mobile | Windows Central

1 more replies
Answer Match 43.26%

They said that it was related to WebView issue, but was it really?

A:Why does swipe-to-go-to-the-comments-section work in the WC app in my Surface 3, but not in my W10M?

It works on my 950 XL.

1 more replies
Answer Match 43.26%

When i open any webpage in microsoft edge in my w10m (Lumia 640 xl with official w10m build 10586.218) and start to scroll up and down, the webpage stutters a lot and sometimes it becomes completely blank. The only way to get that webpage to normal is by entering the tabs view and then re-opening the current tab or zoom in and out inside that webpage. I have been facing this issue since a long time (since insider build 10586.63). Did a hard reset couple of times after updating to newer builds but that didn't help. Therefore rolled back to the official release but the issue is still there. Is anyone here facing this problem and is there any fix for this problem?
Note: I am using Lumia 640 xl dual sim official release build 10586.218

A:Why there is still the annoying stuttering issue in microsoft edge in w10m.

Originally Posted by Andy620 When i open any webpage in microsoft edge in my w10m (Lumia 640 xl with official w10m build 10586.218) and start to scroll up and down, the webpage stutters a lot and sometimes it becomes completely blank. The only way to get that webpage to normal is by entering the tabs view and then re-opening the current tab or zoom in and out inside that webpage. I have been facing this issue since a long time (since insider build 10586.63). Did a hard reset couple of times after updating to newer builds but that didn't help. Therefore rolled back to the official release but the issue is still there. Is anyone here facing this problem and is there any fix for this problem?
Note: I am using Lumia 640 xl dual sim official release build 10586.218 What if you change the scaling settings in display? It might make the experience better
Also, in edge, under settings you should have website preference (either mobile or desktop). Could you change that and test to see if it works better?

9 more replies
Answer Match 43.26%

OK, simply put I'm sick and tired of other programs running in the background hijacking my current window.

ie: I start a process in one window that may take awhile, switch to something else to work on... when the background process is done, depending on the program, it will often force itself to the front. VERY frustrating when you're working on something else, then some background task decided "No, I'm going to take you out of that form box your typing in because I'M coming to the front".

Is there a setting anywhere that can stop background program from hijacking the current window you're working in?
 

More replies
Answer Match 42.84%

Phone specs: Lumia 830 running the latest W10m beta fast ring version. I used this feature to download uhm.... videos.... of uhm... you know.... things, and I was really pleased with it. Few days before installing the latest W10m update, the download feature suddenly stops working. Hoping that it will be fixed in the latest update so I didn't report it right away. But few days after installing the latest update the same issue is still going on, it just wont proceed to download a video. Yes I did all the basic diagnostics like soft reset and stuff. I also cleared up some space both in the C drive and storage. No I didn't changed anything in the settings before the issue occurred, it just happened. And no I haven't done a hard reset yet. Thanks,

More replies
Answer Match 42.84%

The swipe to go frwd or back ( especially back) in edge browser for w10m is an annoying feature which I want to disable...is there a way?

More replies
Answer Match 42.84%

After updating my Lumia 830 with the W10M Anniversary Update (17.08.2016) my Settings stopped working. Seems like the app is not installed. When clicked it leads me to the the shop. Additionally MS Edge is crushing when started.
Any ideas what can be done?

A:Problems after W10M Anniversary update - Can not go into Settings and Edge missing

Originally Posted by Windows Central Question After updating my Lumia 830 with the W10M Anniversary Update (17.08.2016) my Settings stopped working. Seems like the app is not installed. When clicked it leads me to the the shop. Additionally MS Edge is crushing when started.
Any ideas what can be done? try a soft reset: Soft Reset is holding the Volume Down & Power buttons until the phone vibrates and reboots (about 10 seconds). This rebbots the phone with a cleared out RAM and Cache. No data is lost. It is good for when the phone freezes or you experience a glitch of some sort.
Then check for app updates in store
If you need additional help or have more questions or details to share, please join the site so you can reply in this thread. See this link for instructions on how to join Windows Central.

1 more replies
Answer Match 42.42%

hi i have just built a pc up out of parts i had and have installed windows 7 build 7600 on to it the motherboard is a matsonic ms 9127c as matsonic dont have a web site i cant locate the audio driver for it i have tried windows update site with no joy i have tried the matsonic instalation disk but says windows 7 is not supported i have had the sound on for a few mins but kept getting bsod i ran belarc advisor the mother board comes up as p4x44-vt8235 via based i think can any one help find the audio driver please this is the mother board
http://www.geeks.com/details.asp?invtid=MS9127C&cat=MBB

A:new build pc driver problems

Hi -

Run a DirectX Kernel Diagnostics report -
START | type dxdiag | if x64 - bottom-center of screen "...64-bit.." | save as text file

Attach zipped text file to your next post.

Regards. . .

jcgriff2

.

3 more replies
Answer Match 42.42%

Does anyone know if there is a app for windows 10 mobile similar to the Kodi app in the android store/ windows 10 direct download from website?

More replies
Answer Match 42.42%

From past some days Outlook account in people app in continuous syncing. All the people photos are deleted & may be some contacts too. The bad thing is that all this is synced with my PC too & there also its the same problem of continues syncing. I lost so much data in this.
Logging into outlook through browser, I came to know that my outlook is upgraded.
Do anyone has any idea whats going on here? I am loosing my mind.

More replies
Answer Match 42%

There has, so far, been no issues with drivers for 7000 for the Acer 5920gmi that I use. To disable my touchpad I installed the Synaptics driver just to disable the touchpad.

All drivers installed during installation and on first update the rest were installed.

It is a perfect scenario.

A:W7 build 7000 driver install

  
Quote: Originally Posted by echrada


There has, so far, been no issues with drivers for 7000 for the Acer 5920gmi that I use. To disable my touchpad I installed the Synaptics driver just to disable the touchpad.

All drivers installed during installation and on first update the rest were installed.

It is a perfect scenario.


So the whole process has been pretty painless, way to go man.

Norm

5 more replies
Answer Match 42%

Installed the latest preview on my Dell Venue Pro 7139 last night, then spent a couple of hours cleaning up driver issues. It ate my Dell/Atheros 1537 WiFi/BlueTooth drivers completely, and rolled back Intel HD Graphics, Intel MEI, SMBus controller, memory controller, and more. I'm curious to know if it's just this machine, or if others have experienced similar difficulties.
This used to happen back before the Insider Preview program got started, before Windows 10 was officially released on 7/29/2015. But it's been a while since I've seen these kinds of gyrations.
Thanks,
--Ed--

More replies
Answer Match 42%

If what I have shared about what I have just got done building shows in the info under the post anyone have a thought as to why my card doesn't register with my machine? It seems everything else is fine. For some reason it just doesn't seem to be picking up that the card is there and is just going by generic default display properties. Know it isn't the power supply, the MB has the PCI-e 3.0 slots, and have tried two different ones. The fans on the card run, it has plenty of power going into it from what I can tell. I just can't seem to find anything as far as software for it on the disk that came with it or even through the download section on the site, just doesn't seem to really install anything.... Any thoughts?

ASUS P8 Z68-V/Gen3, 16gb memory, intel ivy bridge 3.5 gen 3, sapphire hd 7950 3gb graphics card (which isn't registering) Cougar 1000w modular PSU.
 

A:New Build, Cannot Install Graphics Driver

jmortj5

please start your own thread for your own problems

http://www.techpowerup.com/forums/showthread.php?t=180257

check the power plugs to the card are secure and the aux power plug to the m/board

have you installed the drivers and software for the card

check if you can disable the onboard in the bios
 

3 more replies
Answer Match 42%

Greetings, all,

At my workplace, we have created a central store for all of our device drivers. It is shared out via DFS and includes just .INF files and the associated driver system files. Currently, we have the Windows automatic driver search looking in this share to find drivers. The problem is that we have nearly 6GB of drivers out there, and it can take incredibly long for a Windows client to read through all of the .INF files and find the one it wants to use. We have a hell of a lot of sites, and not every site has a file server to use as a DFS point. So most of them are getting the drivers via very slow connections back to our main site.

I know that Windows databases drivers that are stored in its local driver store. Some of the database files are INFCACHE.0, DRVINDEX.DAT, INFSTOR.DAT, etc. Is there any way to generate a database of the drivers on our store that Windows clients can review instead of reading every .INF file? I have done a lot of research, but I cannot find anything that does what I'm looking for.

Thanks in advance for any help!

 

More replies
Answer Match 42%

I have an issue when trying to restore backup after factory reset on my Lumia 950. I just receive error message which says can't connect to service. The error message is in Finnish so in English it might be somewhat different, but I think message is clear anyhow. Restore goes to about 20%, but after checking the safety code this error appears. I have tried WLAN both at work and at home and also mobile data. Any ideas how to solve this or is there just something broken at Microsoft?

A:W10M backup restore says can't connect service after safety code check on Lumia 950

Originally Posted by Windows Central Question I have an issue when trying to restore backup after factory reset on my Lumia 950. I just receive error message which says can't connect to service. The error message is in Finnish so in English it might be somewhat different, but I think message is clear anyhow. Restore goes to about 20%, but after checking the safety code this error appears. I have tried WLAN both at work and at home and also mobile data. Any ideas how to solve this or is there just something broken at Microsoft? it sounds like a local server side iussue.... wait one hour and retry

1 more replies
Answer Match 41.58%

Hi all.

I've just received a shiny Z30-B (PT251A-008002) which will - if I can get this working - become the new workhorse for the work fleet.
Nice machine.

My only hurdle so far, is the very first one, getting it to boot into WinPE so I can apply a Task Sequence, and build it from SCCM.
I've found the correct LAN driver on the Intel website and applied it to the boot image, but it doesn't work.
I require the WinPE drivers.

The Intel package does contain "WinPE" drivers, but they don't actually seem to apply to my model laptop (if I look in the .inf file), and do not load, I tried them anyway.

If there was an SCCM driver package for this laptop, it would be awesome.
Failing that, just the LAN driver for WinPE would be perfect.

Appreciate any help or advice.

Thanks
Ryan

A:Portege Z30-B - WinPE LAN driver for SCCM build

I have downloaded these versions (all available from Intel.com) of the Intel I218-LM Windows 7 32bit driver (e1d6232.inf) and none of them have worked - so I must be looking in the wrong direction...

18.4
18.5
18.6
18.7
18.8.1
19.0
19.1
19.3
19.5
20.0
20.1
20.2

10 more replies
Answer Match 41.58%

Hey hey.

Vista x64 build 5456
nForce SLI AMD
AMD 64 X2 chip

anyone know of any working audio driver?
i got a beta nForce SLI AMD Audio Driver from nzone but it didn't work.

if i can't get it to work, i'm going to format my vista partition and try it all over but with the 32bit version.

Vista's internal video driver recognized my 6600GT with no problems, everything runs sooo smooth. my only holdback is the harddrive that i am using for my Vista partition.
 

A:build 5456 nForce AMD audio driver???

9 more replies
Answer Match 41.16%

So based on my crashdumps (ignore anything older than 2015, as those BSODs were caused by Nvidia drivers in my old build) it seems the issue is tied to CI.dll and anti-virus software. I'll probably run malwarebytes in safe mode as well as scannow from boot to check for viruses for that.

Where I'm conflicted is could this be related to my recent GPU issues? I thought the BSODs would be caused by the AMD gpu which has consistent issues. The driver will quit working then recover. Flash player appears to have odd lines pop up and sometimes it will just go completely black, despite being fully updated. Tonight my primary monitor had a bunch of lines on it but they disappeared when I changed the orientation to portrait and then back to landscape.

The last three crashes in the dumps have been "likely caused by": CI.dll, unknown image (though it seems to be tied to microsoft's anti-malware msmpeng.exe) and NTFS.sys. Are these related?

Things I've already done: Using DDU re-ripped out AMD drivers and re-installed, checked BIOS (it is up-to-date), run chkdsk but not memtest.

Edit: I don't think crashes are related to GPU stress, furmark running now maxing it out at 100% load. So it's not PSU related at the very least.

PC-Thu_02_19_2015__15731_50.zip

A:Multiple BSODs after new build, AMD driver quits working

Problem devices: Standard PS/2 Keyboard ACPI\PNP0303\4&1B9D8964&0 This device is not present, is not working properly, or does not have all its drivers installed.
USB Audio Device USB\VID_12BA&PID_00FF&MI_00\6&1A624F1F&0&0000 This device cannot start.
Run this: Disk Check - Windows 7 Help Forums
RAM: RAM - Test with Memtest86+ - Windows 7 Help Forums (One stick at a time)
SFC: SFC /SCANNOW Command - System File Checker - Windows 7 Help Forums
Update drivers in red and take care of amdacpksd.sys driver and CI.sys

Code:
lirsgt.sys Sun May 17 15:06:57 2009 (4A100BF1)
part of a Copy Protection platform developed by Tages SA
http://www.carrona.org/drivers/driver.php?id=lirsgt.sys

atksgt.sys Sun May 17 15:36:34 2009 (4A1012E2)
part of a Copy Protection platform developed by Tages SA
http://www.carrona.org/drivers/driver.php?id=atksgt.sys

GEARAspiWDM.sys Mon May 18 14:17:04 2009 (4A1151C0)
CD-ROM Class Filter Driver by Gear Software.[br]Also comes with iTunes
http://www.carrona.org/drivers/driver.php?id=GEARAspiWDM.sys

LGBusEnum.sys Tue Nov 24 02:36:48 2009 (4B0B38B0)
Logitech Keyboard
http://www.carrona.org/drivers/driver.php?id=LGBusEnum.sys

LGVirHid.sys Tue Nov 24 02:36:48 2009 (4B0B38B0)
Logitech Gamepanel Virtual HID Device Driver
http://www.carrona.org/drivers/driver.php?id=LGVirHid.sys

vmm.sys Thu Jan 21 11:38:48 2010 (4B582EB8)
Virtual Machine Monitor driver - Microsoft Virtual PC 2004
http://www.... Read more

7 more replies
Answer Match 41.16%

I need thinkpad T60 bluetooth driver in win7 build 7000 (the auto update one via windows update, not the levono website vista driver).

A:need thinkpad T60 bluetooth driver in win7 build 7000

on of our stickys has the solution....
Windows 7 Driver catalog

2 more replies
Answer Match 41.16%

Hp broke the x64 driver for win 8.1, seems now after working fine on win 10 32 bit for months build 1511 has broken the 32 bit driver, not the printer as it still works on a dual XP boot, what are they playing at?

A:Build 1511 breaks HP DeskJet 710C driver

Found a workaround, removing the LPT port in device manager then scanning for changes reinstalls the port and printer which restores printing. I suspect this works until next reboot where you must repeat the removal procedure.

0 more replies
Answer Match 41.16%

i've had 2 BSOD's in this month on my new computer. They're about 2 different things and i'm inexperienced at fixing crashes. i've opened the .dmp files in Win Debug but i really don't know how to use the information it's giving me. This forum has helped a ton of people and i hope that it will help me as well. I have attached the .zip file in this thread as your forum rules say. if you need any additional information, contact me in a comment to this forum. Thank you. (the attachment thing in this forum is wierd)

A:BSOD, Custom Build, about usbhub.sys and other probably system driver.

ok the probably system driver thing might be incorrect
this is ALL the information Debug gave to me (its not a lot):


Code:
fffff880`0691d000 fffff880`06970a80 lvrs64 T (no symbols)
Loaded symbol image file: lvrs64.sys
Image path: \SystemRoot\system32\DRIVERS\lvrs64.sys
Image name: lvrs64.sys
Timestamp: Tue Jan 17 22:40:36 2012 (4F166964)
CheckSum: 00061E9E
ImageSize: 00053A80
Translations: 0000.04b0 0000.04e4 0409.04b0 0409.04e4

9 more replies
Answer Match 41.16%

Hey, well i have a problem with my GTX 280. The drivers are just messed up like crazy. I have the latest 185.81 x64 Windows 7 driver and i tried 181.71 and i still get problems. When i watch movies i get some major glitches like this

And when i run a game, the FPS it extremely low. Can someone help me?
Here is my system Specs:
Samsung SincMaster 2253LW
Windows 7 x64 7068+Windows xp pro sp3 x32
Antec 1200
Gigabyte GA-Ep45C-DS3R
Intel Core 2 Quad Q6600 w/xigmatec hdt-s1283 at 3.2ghz
Patriot 6gb ddr2-800
Nvidia GeForce GTX 280
ThermalTake true power 600w|Seagate 320gb
Logitech vx revolution
Apple alumnium keyboard

A:Glitches-Windows 7 x64 build 7068 GTX 280 driver issue

Hi jvz555, are you overclocking in anyway?

9 more replies
Answer Match 41.16%

Hello,

Here is what has happened.

My computer was built last December, and has run like a clock, a very fast happy clock.
I went to download a new version of iTunes and encountered issues with iTunes not installing correctly. I then noticed I was missing my Open With... command, so I decided to do a re-install.

I downloaded every new driver from Gigabytes site, and just had horrible issues trying to get Intel Pre Install SATA driver & Intel Rapid Store installed.

I successfully got Intel Rapid Store installed, because I noticed that Gigabyte was not offering .NET 4.5 which Rapid Store needed. (Their download is .NET 4.0)

However, for past hour I have been struggling to get Intel Pre Install SATA in. (I think)
When I extract the file I am greeted by this-
A folder that says 64 Bit
Inside that folder is the following-
iaahcic
iaAHCIC
iaStorA.sys
iastorac
iaStorAC
iaStorF.sys

I know when I first built this system I always had setup, or some exe file and would just click that and items would install. What do I do with these files?
I even tried to go to device manager and click update drivers, but when I direct it to this location nothing happens. (Or at least I don't think anything does). How do I know if it installed? Everything else I install (Intel INF, Management, Marvell etc... I can see in Programs & Features.

Any help would be greatly appreciated!!

**EDIT**
One quick non related question if I may-
The 100MB partition that Windows makes (sometimes) ... Read more

A:How Do I Install Intel Pre-SATA Driver on this build (& other issues)

The IRST Pre-Install driver is meant to be used with RAID. For example, if you set your storage configuration as RAID 0, Windows setup will ask to provide the Pre-install driver. When we do a regular install in AHCI mode, Windows will use it's own generic AHCI driver "msahci.sys" to access the SATA interface. After install completes and IRST installed, SATA driver will be updated to the latest version instead of generic one. In short, you don't need to manually install the F6 floppy version of IRST.

The 100 MB partition may came handy if you enable full disk encryption with "Bitlocker". Unless you need to create four primary partitions on the disk, there is no real benefit in excluding this partition.

9 more replies
Answer Match 40.74%

I am getting various BSODs after installing Windows and still haven't figured out the cause of the problem and what I need to do to fix it.

Here is a log of what I did/problems I experienced (don't know if helpful):

-installed windows 8, drivers for motherboard, gpu, and wireless adapter
-installed avast, various softwares, chrome, borderlands 2
-could not start borderlands (encountered a problem and had to close with no explaination)
-tried to install path of exile, skyrim, BSOD during install process, pfn_list_corrupt, irql not less equal, others.
-Uninstalled Avast and fixed the Avast issue (ran whocrashed and listed Avast as a cause)
-Updated motherboard BIOS to 1.5, BSOD problem persists with game installs, chrome still crashes a couple times (Aw, Snap! crashes)

-Installed windows 7, got BSOD during installation process but was able to boot to OS, windows 8 files located in windows.old folder
-installed motherboard drivers directly from website, installed GPU drivers from disc (did not upgrade), installed wireless drivers from website
-could not install VGA driver from website due to compatibility error
-installed various software, tried to install skyrim, still BSOD
-tried to delete windows.old file but some parts are still left out (don't know if this is an issue or not)

-memtest: overnight with both memory sticks attached, 7 passes
-bluescreenview: all BSOD have ntoskrnl.exe highlighted in red (some have ntoskrnl and other drivers highlighted
-chkdsk didn't come u... Read more

A:Multiple BSOD in custom build can't tell if driver or hardware issue

Hi,

Your installation is counterfeit activated using the LENOVO (BLACKLISTED!) key.
There is no point analysing your issue as your system may be compromised by the Activation
exploit used.


The best course of action is to:Purchase a legitimate Windows 7 licence.
Format the HDD.
Reinstall Windows and activate.

1 more replies
Answer Match 40.74%

I just upgraded to the latest build of Windows 10 1607 64 bit & my hp 802.11b/g wireless network adapter doesn't work & says error code 10 failed to start & took the card out of pc for now but I went to device manager uninstalled & reinstalled it & same thing. On the card Says Anatel on the chip. Does anyone know where do get a driver for this build? or what one works?

Thanks

More replies
Answer Match 40.74%

Hello I have been receiving a couple of BSOD, I believe its a driver issue and I hope I'm correct. I run DS3 Tool for emulators and games that support Xbox 360 game-pad. It is probably a coincidence but the two times the computer has received the BSOD I was using the DS3 tool and another time the DS3 tool and PS2 emulator.

This is a new build the only parts that is not new was the processor, DVD drive, and refurbished WD 1TB hard drive.

RAM was tested with memtest 2 passes I doubt it's a RAM issue will continue test if problem isn't resolved.

No components are overclocked aside from the factory overclocked Gigabyte GTX 760 OC REV 2.0

Computer has good airflow and heat is not an issue.

Also the PSU is a 600W Bronze certified from Corsair which is more than enough for this build.

Help or advice is much appreciated

Thank you.

A:BSOD New custom build (0x0000010d) possibly DS3 Tool driver

Your motioninjoy driver is causing issues here.


Code:
Unable to load image \SystemRoot\system32\DRIVERS\MijXfilt.sys, Win32 error 0n2
*** WARNING: Unable to verify timestamp for MijXfilt.sys
*** ERROR: Module load completed but symbols could not be loaded for MijXfilt.sys
MijXfilt+0x363a
It's outdated, so an update could solve the problem but I've encountered nothing but trouble with this driver.


Code:
3: kd> lmvm MijXfilt
start end module name
fffff880`09dd8000 fffff880`09dfa000 MijXfilt T (no symbols)
Loaded symbol image file: MijXfilt.sys
Image path: \SystemRoot\system32\DRIVERS\MijXfilt.sys
Image name: MijXfilt.sys
Timestamp: Sat May 12 05:27:12 2012 (4FADE6A0)
CheckSum: 00022009
ImageSize: 00022000
Translations: 0000.04b0 0000.04e4 0409.04b0 0409.04e4
Also, one thing that has caught my eye is this function.


Code:
00000000`00000000 : 00000000`00000000 00000000`00000000 00000000`00000000 00000000`00000000 : Wdf01000!imp_WdfUsbTargetDeviceSendControlTransferSynchronously+0x8a
It looks like the Kernel mode framework has tried to obtain information through a Control Transfer and something has gone wrong.

If I look at the loaded modules I see this.


Code:
Unloaded modules:
fffff880`0a3d2000 fffff880`0a3f4000 MijXfilt.sys
fffff880`0a200000 fffff880`0a211000 xusb21.sys
fffff880`0a38b000 fffff880`0a3ad000 MijXfilt.sys
fffff880`0a3ad000 fffff880`0a3be... Read more

1 more replies
Answer Match 40.74%

Hi guys,

I get random BSOD (about every 30mins to 1 hour) off my 1 week old new build. I am experienced at system building and this in my 6th self build and I have never had a problem, but this has me stumped.

I get the BSOD during general windows usage, checking email, browsing, youtube etc. I can run 3Dmark11 without a problem as well as Prime95 on the CPU.

The blue screen says the graphics driver has failed to restart.

THe failed file is atikmpag.sys

Spec:
Gigabyte X77 UD5 Motherboard
Intel i7 3770K CPU
16GB Samsumg DDR3 1600mhz RAM
120GB Crucial M4 SSD
3GB ATI 7970 GFX Card
Windows 7 Premium 64 Bit

I have the latest ATI drivers and have run Memtest86 on the RAM with no faults. I have even reinstalled the ATI drivers.

CPU and GFX Cards are at stock speeds and vaults.

Please find attached the dump file(s) and sys health report.

Any help appreciated.

A:Random BSOD's - Failed to restart graphics driver - New build

Security Software: ??? I recommend the following:Download and install Malwarebytes, update it, do not start the free trial, and then run a full scan. Also run a full scan with your antivirus software installed on your system. If you do not have antivirus software installed, see the Good and Free system security combination. for better security steps and scanning tools. Make sure to update the security software before running the full scan with it.
Your Creative audio driver is out of date. It may be conflicting with the graphics card. Creative Worldwide Support

Your graphics card crash is due to a TDR Error.







  
Quote: Originally Posted by H2SO4


These are all stop 0x116 VIDEO_TDR_FAILURE conditions.

It's not a true crash, in the sense that the bluescreen was initiated only because the combination of video driver and video hardware was being unresponsive, and not because of any synchronous processing exception.

Since Vista, the "Timeout Detection and Recovery" (TDR) components of the OS video subsystem have been capable of doing some truly impressive things to try to recover from issues which would have caused earlier OSs like XP to crash. As a last resort, the TDR subsystem sends the video driver a "please restart yourself now!" command and waits a few seconds. If there's no response, the OS concludes that the video driver/hardware combo has truly collapsed in a heap, and it fires off that st... Read more

7 more replies
Answer Match 40.74%

I have a galaxy S3. Love the thing to death.... but after jellybean 4.3, MTP no longer works. I have tried both Kies Air (not a fan) and an MTP update from windows.com that I love, however, neither work. Specifically I am talking about the MTP update I installed from windows. I run the install, restart the PC, and as long as you leave the phone plugged in during this process, all is well. It works just fine. Once you unplug the phone, however, It seems to cease to continue working. I will plug my phone in again and I get the same error I was trying to fix...






Quote:
Hardware ID Missing
Could not identify Samsung (yada yada yada)


I have been made recently aware that there are a great number of fixes to this problem. One of which I have already tried which involves opening RegEdit and changing one of the WUDFSVC services to a 2 from a 1... Needless to say, if it had worked then I wouldn't be here.

-I am using 7 professional X64
-It is an S3, verizon, 4.3 jellybean build
-It is pissing me off (oh wait, thats not a spec...)

Anyways, If anyone has any suggestions. I have been made aware to try uninstalling drivers and restarting but I have no clue what to uninstall and from where.

A:MTP driver update only works until you unplug android device build 4.3

Got it figured out.... It involved installing some verizon bloat that I really didnt want, but I got it working!

8 more replies
Answer Match 40.32%

Hi
New member - please be gentle if I haven't followed the correct procedures
Okay I rebuilt my PC completely following a mobo failure, retaining the hard drives; I was really impressed Win7 Ult x64 booted straight into the desktop.
I removed old mobo drivers, added new ones
Had a few glitched with the USB ports which I think I fixed by deleting and reintalling new drivers

I have had some BSODs - 2 one after the other just now and at least 1 earlier one while the machine was unattended
In each case it was a BCCode 9f and I got the error message driver_power_state_failure.
Now I have the crashdrump logs.
I think it has zipped 3 but I know the most recent one related to the crash I just saw is called 112905-15444

On a whim in the interim I have also just now uninstalled the Asus AI Suite 3 that came with the mobo (Asus z170 pro gamer) as I know it has an energy management module and even though I have tried to disable that anyway I thought might be a cause for error

I would be most grateful for help in tracking down the cause of this error and advice on fixing it please!

Thanks

More replies
Answer Match 37.8%

Have the apps being developed for W10M improved in quality or features compared with the old 8.1 apps? Or have they become worse?
I remember reading that Uber in W10M is worse compared with WP8.1 but the instagram app in W10M is better
What are your thoughts? Please state which app or apps you're basing your conclusions on
Thank you

More replies
Answer Match 36.96%

I recently upgraded my motherboard, processor and memory, then installed a fresh copy of Windows 7 x64 Pro. I've been having problems from day 1. Originally, the computer would hang at either "logging off" or "shutting down" whenever I'd try to restart the machine (which is frequently when you're having to install drivers and programs). Now, it will still hang, but will then BSOD on me.

I've also come home once or twice and found that it'd BSOD'd while I was away. I think I've updated all the drivers, but like I said - I've been having issues from the start, and I'm not sure everything finished installing cleanly.

BSOD error has consistently been "Driver Power State Failure".

Any help would be greatly appreciated. Dumps attached.

Thanks!

A:BSOD with "Driver Power State Failure" -new build - hangs on shutdown

I'd still love to know what was messing my system up, but I ended up doing a complete reinstall anyway.

My Windows 7 key is an upgrade key, and Microsoft makes finding install media unnecessarily difficult. The image I used the first time was a bit... sketchy. I'm hoping that this time around I won't have the same issues, but I guess only time will tell.

1 more replies
Answer Match 35.7%

Can I install Icon Packs designed for Build 7600 to Build 7601?

An Icon Pack was saying install on to 7600 only and after I checked my regedit, I learned that I have 7601 (Probably SP1, I don't know).

Would I have any problems if I install the icon pack?

Thanks.

A:Can I install Icon Packs designed for Build 7600 on to Build 7601?

You can normally install icons anywhere you like, on any machine or system which uses them, they are merely small graphics of various types. Unless the "Icon-pack" is using software to install something else, ( in which case be careful what it does), you can install it anywhere.

Some "Icon-packs" make extensive changes to system files, are dependent on the system to which they are installed, and best avoided.

Regards....Mike Connor

5 more replies
Answer Match 35.7%

My win 10 pro build 10240 hasn't received the November update build 1511 while my other win 10 home versions have. I know I'm not the only one having this problem but here's my two cents. On my xw4600, I upgraded from win 8.1 pro to win 10 pro as soon as 10 was available some months ago. I still receive other windows updates. I downloaded the most recent iso from the media creation tool but I don't have an option to mount it from the right click menu. Both sfc and dism have no issues. I would burn it do a disk but I've read other users say its just reinstalled build 10240 instead.

I was using another random win 10 pro computer at work today and noticed it hasn't received the November update yet either. Anyone else with win 10 pro that did get the update?

Maybe this issue has more to it, like when I upgraded to 10 pro I had an issue with onedrive. I don't really use it so I only disabled it from startup in the task manager, but it as a service disappeared (except for registry entries and program files) and I haven't found a way to reinstall it ... yet. I know I could do a clean install of windows but that's not my style. I move from pc to pc over the years using disk images. This onedrive issue is the only problem I've come across that I haven't figured out, without a clean install. I mean, I wiped onedrive from my system completely, registry keys and all, but attempts to reinstall fall short (error corrupted file). During the attempted installation it place... Read more

A:win 10 pro build 10240 hasn't received the November update build 1511

RE : I downloaded the most recent iso from the media creation tool but I don't have an option to mount it from the right click menu.

Did you burn the iso to a bootable media, then insert the media to the computer ?
If that was what you did, then you would NOT see the Mount option.
Instead, you would see the Setup option. Use that to start the installation.

0 more replies
Answer Match 35.7%

My current system was upgraded to windows 7 32bit from vista 32bit (I bought the windows 7 home premium upgrade disc when it was first released). I am going to build a complete new system. Can I install windows 7 64bit from the same windows 7 disc? Or do I have to buy a new windows 7 disc? Is there a way around buying a whole new disc?
 

A:Solved: New computer build work with old build's Windows 7 Disc?

It won't activate and you will end up in Safe Mode permanently. One machne = one license. You need to buy another full version. But you can do it if you don't use 7 on the old machine. You will just have to activate by phone and explain. Then if you go online with both, one will deactivate and go to Safe Mode.
 

1 more replies
Answer Match 35.7%

Yesterday i updated my phone to wat supposed to be anniversary update .i was surprised that my windows build had vecome an insider preview build which in the past i downgraded my phone to version 8.1 then updated to windows 10 original to get away from the insider version..my question is why ot came back and how to prevent it from coming back in the future

A:why my windows mobile 10 build has transformed to an insider preview build

Originally Posted by Windows Central Question Yesterday i updated my phone to wat supposed to be anniversary update .i was surprised that my windows build had vecome an insider preview build which in the past i downgraded my phone to version 8.1 then updated to windows 10 original to get away from the insider version..my question is why ot came back and how to prevent it from coming back in the future Go to settings - Info and check build version.
Annyversary Update is nothing else than Redstone that became official and replacing old Threshold, read the news ;)

1 more replies