Tech Problem Aggregator

how to disable acoustic mode in scsi hard disk

Q: how to disable acoustic mode in scsi hard disk

is there anyone knows how to disable acoustic management in scsi
hdd?
appreciate your help!
thanks in advance
kianlie

A: how to disable acoustic mode in scsi hard disk

Hi kianlie,

This is a feature of some HDDs in order to make them quieter. Unfortunately, because they work by reducing the speed of the drive (according to load), they can make some systems run slow. There are utilities available to turn this feature on and off (where supported), but you will need to get these from the HDD manufacturer's website.

1 more replies
Answer Match 69.3%

Hi there,

I have got two SCSI hard disk arrays running in my server, one is a 3-disks array on RAID-5 and the other one is a 1-disk unRAIDed.

Both arrays are presently holding data.

I want to install another 2 SCSI disks on the second array so that I can RAID these 2 together with the existing 1 on a RAID 5.

Can someone please kindly give me a walkthrough how to do it, because apart from changing hard disks on a PC, I have never done anything with SCSI hard disks before.

Is there any issue with data migration?
Do I have to temporarily transfer the data in the disk to another storage, install the 2 new disks, RAID the three together, then transfer back the data?
Or can I just simply plug in the two new disks, and RAID the three together, without having to worry about the data contained?

Ascan be seen I am in very very desperate need for help here.
So from the time the new disks arrive, what do I have to do?

Thanks so much. Any input is very much welcome and appreciated.
 

A:How to add SCSI hard disk to RAID

I am not sure I completely understand what you want to do. I think you want to install two new drives onto a scsi card and then create a raid array on those two disks.

As long as the scsi controller you are connecting these to supports raid, it should be no problem. Shut down and connect your drive to the controller. The one disk connected now will have the terminator jumper / plug installed on it. This needs to go on the last device in the chain. Now restart and enter the bios for the controller you are setting up the raid array on. There are different key combos for different card mgf's so you need to know which key to hit. When in the raid bios, select the two disks you want to create the array and start the creation process.

I am assuming that the os is already installed on another device and that drivers for the raid card are already installed. Go to disk management and you will need to partition and format your array. You MAY need to restart after you partition the array. Format with ntfs and you are good to go.
 

3 more replies
Answer Match 68.88%

Well I was looking around and in the setup menu it said HDD Acoustic Mode and it gave me some settings.

Bypass which was the default = doesnt do anything

Slow = slow and quiet

Intermediate = well u get it

and Performance which was fast and loud. Im not sure if all those names are riught except for bypass and performance. I was wondering if it would be ok to have it on performance.
 

A:HDD Acoustic Mode?

Yep I would have it on Performance
 

1 more replies
Answer Match 68.88%

Just looking for some opinions on HDD acoustic modes. I got a Dimension 8400 and in the bios it gives an option for changing the IDE drives acoustic mode / sound level. The option that i have on now for "performance" seems alot better for speed, but it makes the HD sound like its 5 years old....while the default (drive manufacturer) setting was obviously slower but i couldnt hear the HD grinding away. Any thoughts or knowledge / experience about this subject? Should i stay away from the performance option? Is it burning up my HD's? Most data that i got im not worried about, and the stuff that i am worried about i make frequent backups of....

Thanks for reading
 

A:HDD Acoustic Mode

6 more replies
Answer Match 67.62%

I have a Startech brand PCI add-in card to get some extra SATA ports on my old Biostar MCP 6PB M2+ board.

In Disk Manager an Hitachi drive attached to the card shows up as a SCSI device.

However my backup software doesn't see it (old copy of Norton Ghost on CD) and the POST operations do not show it in the BIOS. Win7 reports that no driver updates are needed for the Hitachi on the Startech card.

It's very confusing. A new motherboard is due for me but this problem solved would extend the use of the Biostar. Why would the Win7 see the device but nothing else?

More replies
Answer Match 67.62%

I suspect that my 640 GB hard disk (from 2008) is nearing the end of its life and would like to plan for a replacement.There does not appear to be much if any chance to replace such a SCSI disk any more.What is the best type of disk to replace it, and does it need a new controller?I run Vista (original OS) and Windows 7 (new) in a dual boot configuration.It has currently three volumes, a Vista C: drive (c.300 GB), a Windows 7 C: drive (c.300 GB) and the HP "FACTORY_IMAGE" drive 15 GB

More replies
Answer Match 63.42%

Hi

I have downloaded Hard Disk Sentinel and one of the options in this is to change the acoustic management of the hard drive when I change this to the recommended setting which it says is (FEh) as soon as I apply this change it reverts back to the default setting which is min performance and volume (80h). Does anyone know of any other software that allows me to change it to )FEh) to get the best performance out of the drive?

Hard drive is a Samsung HM500JI




Many Thanks

A:Samsung hard drive acoustic management

Offhand, I'd guess that only Samsung software can do that on a Samsung drive.

I'd also guess you are operating the software incorrectly, but I could be wrong. I haven't looked at that type of software in several years.

You might be able to force things back to a default with a jumper setting?

Samsung drives are known to be very quiet, so I think you are on the right track in leaving it on the high performance setting--the drive will probably be quieter than most even on the "noisiest" setting.

9 more replies
Answer Match 63%

windows98 is already on my 13gb ide drive, but i have a new 9gb scsi drive which is really fast 80mb/sec,
I would like to install only windows for now so machine boots faster, can i do this and still have other files on existing slower 13gb hdd i.e. games, txt files and pics?
I have managed to make ide drive as slave but i dont know how to go abouts installing win98 on scsi, as machine keeps booting to windows, from the slave drive. And when i attempt to install win98 it tries to put it on the ide drive which alwready has it on.
Do i need to disconnect the power supply to the ide hdd?
Does scsi drives have master/slave jumper setting like the ide?

My new hdd is MAG3091LC on this page
www.fujitsu.co.jp/hypertext/hdd/drive/disk_e.html
 

A:if i have 1 ide and 1 scsi hard drive how do i install windows on the new scsi hd?

8 more replies
Answer Match 61.32%

Hi,

I am having two hard disk in my system and both are bootable independantly and having different OS. 1st hard disk is having OS Windows XP and another one is having Windows 2000.

When i boot system from one harddisk then I am able to see contents (Drive of another harddisk) of another hard disk.

Could you guide me how to disable to see drives (Contents) of another hard disk?

Thanks & Regards,
Padam Kumar Tripathi
[email protected]
 

More replies
Answer Match 60.9%

Windows XP Home, SP3, 1 Gig RAM, AMD Sempron 3000+ processor. The destination/problem drive is a Western Digital 1.5-TB SATA in an Eagle brand enclosure.

Operations like manually dragging and dropping 20 Gigabytes+ of files and folders copy without error messages. The problem appears only with Norton Ghost 9 and Acronis True Image 11. All drives are formatted NTFS. And Acronis True Image and Norton Ghost are both configured to keep image segments at 1.95-GB.

I have swapped the disk in the enclosure for another disk exactly like it, a 1.5-TB Western Digital SATA in an Eagle brand USB enclosure.

Everything I read suggests I turn off disk cacheing; but, that is grayed out for this external USB drive and I see nothing in the BIOS that helps.
 

A:How to disable write cacheing for USB hard disk

Looks like I may have found a solution at:
http://support.microsoft.com/kb/330174

There were several solutions offered on the page; but, this is the one that worked and the 7FFF value is the one I used.

So far, I have completed one Ghost backup image and I have started another that is now at 17%. Before I made the registry modifications below, it stalled at 2% on all attempts with the "Delayed write failed" message.

1. Click Start, click Run, type regedit, and then click OK.
2. Locate the following registry key:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Session Manager\Memory Management
3. In the details pane, right-click the SystemPages value, and then click Modify
Note Default value is 0 (hex)
4. In the Value data box, type 7FFF, and then click OK.
Note You could try using the following alternate values:
* 7FFF = 32,000
* PTEs BFFF = 50,000
* PTEs 24FFF = 150,000 PTEs
Note The FFFFFFFF value should not be used. If you set it too high, you might run out of paged pool memory.
5. Exit Registry Editor.
6. Restart
7. Monitor the Memory \ Free System Page Table Entries in Perfmon.
 

1 more replies
Answer Match 58.8%

ok so im dealing with a laptop and uppon buying a hard drive and putting it in and installing windows i get this annoying windows detected a hard disk problem popup each boot.

i know what it means but im not buying another HDD just got this today

i need a way to hide the error and please dont say

?Task Scheduler Library? => ?Microsoft? => ?Windows?. => ?DiskDiagnostic? or anything to do with gpedit because this is windows 7 home basic and does not have those options

also i force install the gpedit and it does not have a DiskDiagnostic tab. so i need another way around this

windows is acting 100% fine a i believe its a false positive to i choose to ignore the error.

A:LENOVO laptop Disable windows detected a hard disk problem

Well i found nothing to fix this issue so i killed it from the root. found the .exe that is responsible for the prompt "DFDWiz.exe" & "DFDWiz.exe.mui" and renamed it and prompt gone. had to go thought such extreme measures but hey it worked.

for anyone also looking on how to remove the message

i took permission of the whole system32, right click system32 folder with the take ownership.reg (provided below) then look for the 2 files "DFDWiz.exe" & "DFDWiz.exe.mui" and rename them to something like Old-DFDWiz.exe & Old-DFDWiz.exe.mui

then reboot. Done

2 more replies
Answer Match 57.12%

I've been having the same problems I posted in December here:

http://forums.techguy.org/windows-nt-2000-xp/658760-slow-running-other-issues-have.html

That time I just re-installed wondows (for the second time due to those symptoms) this time I've been getting the same symptoms, but have worked it out finally...

My Primary IDE Channel was reverting to PIO mode (as it seems to do in XP) - I've returned it to uDMA as per the instructions here:
http://winhlp.com/node/10
and the event log shows a few instances of the following:
Event Type: Error
Event Source: atapi
Event Category: None
Description:
The device, \Device\Ide\IdePort0, did not respond within the timeout period.

and

Event Type: Warning
Event Source: Disk
Event Category: None
Description:
An error was detected on device \Device\Harddisk0\D during a paging operation.

I've run chkdsk, and will defrag tonight. But clearly there's an ongoing hardware problem.

Might this be corruption on the disk? If so - any suggestions for a good HD surface-scan utility?

If it might be the connections or something else, I would appreciate any pointers on what I should be looking for before I open my comp up.

Many thanks
 

A:Hard disk reverting to PIO mode

Go to the hard drive manufacturers website and download their Hard drive diagnostic utility. Most will create a bootable floppy or a bootable cd. Boot from it and test your hard drive.
 

3 more replies
Answer Match 56.7%

I've looked at numerous guides to try to disable this option, but all are for 95/98.

Is there a way to disable this feature in Windows XP?
The reason being is that this is the suggested solution for getting Diablo II to work. Even though I have the CD in the drive, it says that I don't. And I only have one drive.
 

A:"Disable all 32-bit protected-mode disk drivers"

6 more replies
Answer Match 55.86%

I just bought a Western Digital Black hard drive: WD Caviar Black 1TB Internal Serial ATA Hard Drive for Desktops WDBAAZ0010HNC-NRSN - Best Buy

I have it attached to this motherboard: GIGABYTE - Motherboard - Socket 775 - GA-P35-S3G (rev. 1.0)

The symptoms of my computer are that Windows may run very slow, disk usage is high, and Windows explorer will stop responding often. When I boot into safe mode and run Western Digital's Data Lifeguard Diagnostic the extended test succeeds. When I'm not in safe mode it fails and says "too many bad sectors." The quick test does not finish in Normal mode and says something like "error code 02 - interrupted by a hard or soft reset."

Windows update will also say "Windows cannot search for updates with error code C80001FE."

What could be the reason for this and how can I trouble shoot it?

I have installed all the drivers necessary on my computer. I have AHCI set in the BIOS also. It is a fresh install of Windows 7 Ultimate.

A:Hard Disk Check Fails In Normal Mode

I would RMA the drive back to Best Buy and get a replacement. The drive is obviously bad. It happens a lot more often than many people think. Erase the drive and take it back and tell them it is defective and failed Western Digital's diagnostic test.

9 more replies
Answer Match 55.02%

Hello

I installed Windows XP Mode and Windows Virtual PC a few days ago on my drive. At that time I had 160 GB free.Then In noticed I was losing space. So I decided to uninstall them both. I did that and I removed the other things like the VHD Drive and the XP Mode Application. I removed all of that and I got a few GBs back but no matter what I delete, the problem persists and after a few minutes I end up losing the space I got back and more! I got on Google and reviewed cases like mine but nothing did the trick. I had as low as 108 GB. But I went to Disk Cleanup and pressed the Remove Old Restore Points and Shadow Copies button and I went from 108 to 140 GB! This is great! But I still need to know what happened to the other twenty I had.

And, I don't know if this helps, but right before I had 160 GB ( and before I installed XP Mode on my Hard Dive ) my computer was in a similar scenario which happened a few days ago (It had about 68 GB). I used TreeSize to find the file that was eating up my Hard Drive and I found out that my Temporary Files ate up a whopping 90GB! So I cleaned them out with CCleaner.

I hope you can find out what happened. And hurry please!

Thanks in advance!!!

A:Installed and Uninstalled XP Mode and now my hard disk is losing space

This is odd behavior, Do you have hibernation enabled on that machine?

oh and just to be clear we are talking about the directory that appears if you type
%temp%
in the search bar and hit enter right?

9 more replies
Answer Match 54.18%

Hi there,
My sister just bought a new desktop. It was working fine and all. But this morning, she forced shut down a windows update. The next thing happen once it gets past through BIOS is
"Reboot and select proper boot device or insert boot media in selected boot device and press a key"
So I told her to look at the BIOS setting and it only recognise the Optical Disc Drive of
"SATA SM: TSSTcorp CDDVD SH-2"
as shown in the picture below

Is there anything I can do? I tried opening the desktop case and see everything is loose, but everything was still in tact.
Any suggestion would be much appreciated.
Thanks in advance.

A:Hard Disk Drive not found in ASUS UEFI BIOS Utility - EZ Mode

Try reinstalling the driver, changing cables. If it can't be recognized then boot the maker's diagnostics DOS CD scan to test it - Seatools if there isn't one - or Partition Wizard bootable CD surface scan. If these won't see it you can slave it to another PC to try Disk Check or see if it will see it. If not then I'd replace it.

Do a Clean Reinstall on the replacement drive from tutorial in my signature below if you want it perfect.

1 more replies
Answer Match 53.76%

Despite exhaustive exploration & testing, I have not been able to get Win7 RTM to properly run my SCSI hard drives.

Though my XP OS & hardware passed MS's WIN7 compatible test and my actual 32bit Win7 RTM install, recognizes my Adaptec 2940U2W PCI SCSI Host AND successfully installs latest available** XP\Vista 32bit drivers, my SCSI DVDrom & HD's will not function properly.

[** - Adaptec will not update this driver beyond Vista compatibility]

After ""successfully"" loading the SCSI host drivers, both my AHCI SATA & SCSI drives are visible in 'My Computer' BUT NOT in native Win7 'Computer Management' & 'Storage' / 'Disk Management' screens for drive management. In fact, when selected, 'Disk Management' loops/hangs & becomes non-responsive and requires a hard reboot to clear.

Has anyone else with "SCSI's" experienced this?

Has anyone with any brand / type of SCSI controller & drive combo, succeeded in BOTH installing & properly running same?

Does anyone know if the upcoming 'XP mode' patch update will enable 'true' SCSI drive usage within Win7?

Thanks

A:Win7 w XP Mode vs SCSI

No, "xp mode" will not help your install of windows 7 to see your real hardware. It just doesnt work that way. If the vista drivers dont work, then i hate to say it but your out of luck. You can give the windows xp drivers a try, but thats your only recourse.

2 more replies
Answer Match 53.34%

HI to you,

I'm running with an Asus P9X79 Pro, BIOS updated to the latest version and a Corsair Neutron 120GB...
The SATA mode in BIOS is set to AHCI.

But in Windows 7, all drives (1 SSD, 1 WD HDD and 1 Seagate HDD, and Asus DVD Drive) are seen as SCSI devices...

I tried to use only windows 7 64 bits native AHCI drivers and I got the same things as I used the IRST drivers provided by Asus... As I've done many search on the web about AHCI and X79 chipset I've found so many issues and no real answer, I'm deseperatly need help.

As I want to get all the performance and stability of my system I just want to make sure that everthing work as it is design to...

thanks in advance for your help...

A:SSD in SCSI mode instead of AHCI using X79 chipset

That is normal for those controllers/drivers to report SCSI. The drives are functioning normally as AHCI.

If you are connected to the Intel controller, what IRST driver version are you using?

9 more replies
Answer Match 52.5%

My company's computer needs to be patitioned and reformat. The system is still working well. I mean, nothing wrong with anything (weird huh?). Ok the hard disk just need to be 'split'. I mean, make drive C & D on the hard disk. I know how to do that... easy... Then the HD need to be formatted & reinstall windows XP. Ok, easy too..

But the main problem occured before I do anything (partition & format). I have my own bootable CD that I usually use for partitioning & formatting.

Ok, i insert the CD & restart.
I went to BIOS & changed the boot order (1st boot: CD-ROM, 2nd: HDD-0 & 3rd: Floppy). Then restart again.
Ok the bootable CD is excellently loaded.
I typed fdisk, then came the first problem. it says something like 'no fixed disk'. I exit fdisk.
Then I typed format c:, 2nd problem occured. it says something like, 'invalid drive'.
I forgot the error message because the pc is in my office right now. I'm currently at home 'begging for help' So the error message is not accurate. sorry..

I think, if I run the CD, the hard disk will not be loaded (or should I say, hard disk failure). & If I take off the CD & restart again, change the BIOS (1st boot: HDD-0) then windows will load! Weird right?

I don't think my CD is 'corrupted' nor broken because I tried to run the CD from another PC. Yes, I can access the C drive from that PC.

Does anyone have any idea of the ... Read more

A:Can't format hard-disk nor do partition when using boot disk. Hard-disk failure

It sounds like it might be the bootable CD you've created is not picking up the HDD's/partitions.
To eliminate this as a posibility travel to bootdisk and grab the WinME bootdisk and boot from there. If it picks up the HDD you can FDISK and Format from there.
The other option is to boot using the XP CD and let it handle the formatting/partitioning duties...

patio.
 

14 more replies
Answer Match 52.5%

My old XP has been acting up, I don't use this one much anymore. When it starts an error screen appears. It reports that the BIOS in the system is not fully ACPI compliant and to upgrade it, the problem is there is no BIOS that will upgrade this feature for the rvision of the mobo I have. THe message also says I can disable ACPI mode during "text mode setup" by pressing the F7 key when prompted to install storage drivers.

I have tried the last known good configuration but to no avail.

I don't wish to update BIOS but how can I disable ACPI during text mode setup. When I boot hitting F7 nothing happens.
how do I get to tex mode setup?
 

A:Solved: disable ACPI mode during "text mode setup

16 more replies
Answer Match 52.08%

Hi
I have Thinkpad T43, with windows XP professional.

Since few days whenever i launched my ATI catalyst control center I would get BSOD and laptop will boot automatically and then everything would be fine.

Then while browsing my wife downloaded some media player exe, and since then my IE was redirecting to unknown sites (xalab etc) not to mention various ad pop-ups. One of the online video sites gave a message that I have TROJ/Rustok-N. (Also I would like to mention since couple of months my System Restore was not working although everything else was working fine)

I ran spybot, malawarebytes, trojanremover and removed whatever was reported. But the problem persisted, so I renewed my Norton Internet Security (actually got Norton 360), ran scans but it couldnt find anything.

Then I booted in safe mode and ran all these again, last thing I remember trojanremover prompted to remove something like sv~.exe and i did, when i restarted the system in normal mode I got BSOD and laptop rebooted, I disabled automatic restart on failure but it keeps on doing that.

I then went to Access IBM and restored by configuration which brings back the system files to previous state (the most latest point available was 07/2006)
I still got the BSOD while booting into normal mode, but safe mode was working fine.

I then went into safe mode and disabled couple of services on startup, then my laptop booted fine in normal mode, I found that now windows xp was reset to SP2, so i ran windows update w... Read more

A:BSOD 8E while booting into normal mode, Safe mode fine. Disable automatic restart doesnt work.

FWIW: http://kadaitcha.cx/xp/stop_error.htmlAs stated, it's a matter of hide-and-seek, with no guarantee of finding the culprit.Another link that may be useful: http://aumha.org/a/stop.htmLouis

1 more replies
Answer Match 51.66%

Have external SCSI 3TB RAID - need to get it properly configured in Disk Management to actually show up in "My Computer" as connected drive. Running Win2K Pro OS. RAID contains 8 - 500GB drives, and has been initialized. Disk management shows as: Disk 1 Dynamic 2047.99GB Online and Disk 2 Dynamic 1209.22GB Online, but both are Unallocated. (I changed them to Dynamic from Basic - was that right?)I want them set as RAID-5, but am not computer tech and don't know where to go from here and don't want to mess it up. Please advise!

A:Set RAID 5 external SCSI in Disk Management

To use RAID 5 on Windows 2000 Pro you will need a separate RAID controller. Do you have this? Windows 2000 Pro does not support software RAID 5. To implement software RAID 5 you would need a server OS.

4 more replies
Answer Match 50.82%

I'm just wondering... I'm setting up a server and planning on having either a RAID0 or a RAID5 array of SCSI disks.

I could potentially use a SCSI RAID1+0 setup for my backup needs, but I've been thinking along different lines. My system drive/array will be around 300 to 450GB in SCSI, and I'm planning on having a large capacity sata disk or two in RAID1 for data...

... while I know I probably can't use the same controllers, is there any cheap and easy way by which I could have the system drive (scsi striped array) mirrored to a dedicated sata drive for backup purposes, such that if I lose the whole striped array at some point, I'll still have a backup of the lost data with which to build a new array to replace it with?
 

A:Mirror SCSI RAID array to SATA disk?

Krissie,
The good thing about Raid 5 is if one disk starts to die it gives you warning and time to pull it out and rebuild it without missing a lick. If the controller goes you can replace it and your drives will still be fine.

Now if you want to back up your entire network to a SATA array then i would advise investigating Data Protection Manager 2010 (DPM 2010). Full backup to a disk array every day and incremementals every 15 minutes, then a tape backup to take to the bank on the weekend.
 

2 more replies
Answer Match 50.82%

Hi all. I have an Asus P8Z77V-Deluxe mobo with Win8.1x64. The mobo has 4 6G SATA ports, 2 are Intel and the other 2 are Marvell. I have the main OS SSD drive and 2nd internal HDD connected to the 2 Intel 6G SATA ports without issues. Today I added a 3rd SSD drive connecting it to one of the Marvell 6G SATA ports. The drive was picked up by Windows but problem is that in System Tray it shows as a removable SCSI Disk device. I tried to reset the BIOS to default values without success. How can I make Windows see this 3rd drive as a fixed drive and not removable? Thanks.

A:3rd internal SSD shows as removable SCSI Disk Device

That port is probably set as eSATA and windows sees it as external drive. In the bios you can probably set it as "normal" SATA port but Marvel controller is not particularly good for SSDs anyway, you should ideally connect it to primary controller and connect HDD or CD there if there's no available connections on primary (Intel) controller, HDDs and DVDs don't care about it.
If you want to keep present configuration, you can go to Device manager > Disk drives > Policies and set to "Enable write caching for this device", it should make it an "Ordinary" drive.
Oh, just to ad, all IDE, PATA, SATA are part of SCSI standard so it's mention doesn't mean it's conventional SCSI connection.

11 more replies
Answer Match 50.4%

Whenever I boot up my old computer, I get a message during bootup that tells me that the SCSI boot device is not installed. I have a SCSI hard drive connected to an Adaptec SCSI pci card. I had just taken the hard drive and card out of that computer and tried to install them on this computer, and it didnt work, so I put it back. I tried running a SCSI utility on the bootup screen, and it didnt even recognise the existance of the hard drive. It wont let me format or anything. If there is something I can do to get it working, then please post. I do not care if the solution requires reformatting, because I do not have any really crucial data on the drive.
 

A:SCSI Hard Drive

9 more replies
Answer Match 50.4%

Hi,

I have a Dell Poweredge SP5166-2 that uses Seagate Barracuda (4.3gb) hard drives put into trays that are slid into the computer and connected to the motherboard. I want to put another hard drive in but it is an HP C2490A (2.1gb). When trying to install it the first times, bios recognizes it and says it is working properly, but it is not displayed under Win2k's logical devices or my computer. It is however displayed under device manager. So, it does exist but I just can't make it work within my computer. I also tried to make connect the SCSI bus cable that goes into the cd rom into the hard drive, but no luck. Is there any master slave config for scsi devices? My understanding is that there aren't any; only scsi ids. Any help is greatly appreciated. Thanks in advance.

Louis
 

A:HP SCSI Hard Drive

Hi,

You can check couple of things.

You may want to check SCSI ID(which usually a jumper or switch on the drive.).

If you want the drive to be C:, check host adaptor which ID is bootable.

Make sure you have a terminator at the end of the chain.

Go device manager and check if your SCSI card has conflict with other devices.

Good Luck,

TJ
 

1 more replies
Answer Match 50.4%

A couple questions I have concerning SCSI devices....
1) Scenario: You have a scsi cd-rom, 50-pin, and a scsi hdd, 68-pin. The adaptec adapter manuel says for automatic termination, you have to set the 'low/high' setting from 'on/on' to 'off/on'.

Now I've hooked up scsi devices before, but only hdds. My question: by having a 50-pin device (cd-rom) and a 68-pin device (harddrive) both on the same scsi controller card...would that slow the hdd down? To me, it seems like I'm disabling the scsi wide aspect of the card.

2) SCSI-1 is 8-bit, right?

3) SCSI-2 is 16-bit, right? also known as scsi wide, right?

4) What is Ultra wide?

5) Is SCSI-3 and SCSI 160 the same thing?

Thanks
 

A:SCSI Hard Drives

Have very little experence with SCSI but good resources for info. Try the following link for good reading.
http://baden.nu/public_html_index/SCSI/SCSI.html
 

1 more replies
Answer Match 50.4%

I was able to salvage an old system from the trash at work. It has a Western Digital 4.3GB SCSI hard drive and I want to know if i can use it in a non-scsi system. To use it will I have to use a SCSI adapter or have to have all HD's as scsi?
 

A:Using SCSI Hard Drive

You can use it if you have a SCSI adapter and you can mix IDE and SCSI in the same PC.
 

1 more replies
Answer Match 50.4%

I have 2 scsi drives in my compaq evo w6000 pc c & d drive they are 18gb I want to replace c with a 73gb drive can i put in the d drive position & copy c drive to the new drive using norton clone & then put it in the c position & put the old d drive back in the d position will my pc boot without the old d drive when i put in the new drive in it's place so i can clone c drive to the new drive Thank You [email protected]
 

A:scsi hard disc

6 more replies
Answer Match 50.4%

Hi,

I've got an old computer that we've just been using at the office for payroll and a few other things. The problem is its runningout of hard drive space, so I was just going to install another hard drive, but I forgot that it has a scsi hard drive. I was wondering if i could hook a regular hard drive up to the scsi cable? Any help will be greatly appreciated.

Thanks
 

A:SCSI Hard Drive

No.
 

3 more replies
Answer Match 50.4%

Built a WinNT 4.0 server using SCSI raid array. Works fine. Enabled atapi in services and it sees the IDE CD-ROM (master, secondary channel) just fine.

But it won't see the IDE HD (master, primary channel)!

Jumpers, cables, HD all okay.

I'm sure I'm missing something obvious. Anyone have a clue?

Thanks,

Jim
 

A:scsi NT -- how to add IDE hard drive?

Greetings

Can your BIOS see the HD? If not, then your OS has no chance of ever seeing it.

Have you tried it as a Slave on the secondary controller? Or better yet, keep it as a master, and make your CD-ROM the slave on the secondary controller.

You could have a dead primary controller (I know my secondary controller is not functioning... damn, I need a new PC - who wants to help me raise funds for a new PC - any compnay that helps will get free advertising from me ), or a dead HD.

There could be something else wrong, but I am not that great with hardware issues. If you want, I can move this to the Hardware forum.

Cheers

------------------
Reuel Miller
Windows NT Moderator (yes, that does make me biased )

[email protected]

Website: www.xperts.co.za/reuel/multiboot

Every morning is the dawn of a new error...
 

2 more replies
Answer Match 50.4%

In a recent attempt to upgrade my video card I have come across a strange Hard Drive issue.

My system is a Dell 2.8 GHZ (running XP) and I purchased a new 256MB AGP video card to replace the stock 128MB... as a precaution before I did this, I took out the ATA adapter card in a PCI slot that runs 2 seagate ATA drives. After my installation was complete I put the ATA card and drives back in.

Now my Device Manager sees them both, but it reads them as SCSI drives and my ATA adapter as a SCSI adaptor, and It thinks one drive is empty, and the other needs to be formated.

My remedy was to re-install the driver for the ATA card, no luck, so I checked the jumpers and bios settings, no luck... called and spent 1 hour with Seagate level 2 support, no luck (we did test both drives and seem to be fine)

My E drive has a capacity of 279 GB and there is about 80GB of data there and my G drive has about 185GB on it with a capacity of around 200GB.

Does anyone have a suggestion on where to go from here? (With out reformating my drives and losing 250GB of data)

Thanks in advance.
 

A:2 ATA Hard Drives seen as SCSI

16 more replies
Answer Match 50.4%

Hi,

I've just bought some hard drives.
They weren't expensive, i got them in a clearance sale, they are SCSI types.

One of my PCs uses an SCSI hard drive as its local drive 'C',
However this PC has a power supply feed to the SCSI hard drive, and also the
SCSI connector ribbon cable.
Thats two separate cables.
One for signal, and one for supply.

The SCSI hard drives i bought have no feed point for a power supply.

So i don't know how to try them.
They must use some supply to operate, so could it come via the SCSI cable ?
I suppose it must come from there ... ?

Ive never seen ones like this before.

I dont want to try them without checking first.
Any comments or suggestions would be welcome.

Model: WDE18300-6029A8
Made: 26th May 1999

I got eight in all, some like this one, and some others.
Now i'm a bit worried about trying them, as they might try to draw more current
from the SCSI signal wires than they were meant to give.
These ones come in a sort of Slot-in carrier, what difference that might make
i don't know.

Cheers, John
 

A:Some help please in trying to use an SCSI hard drive.

14 more replies
Answer Match 50.4%

ok i posted eariler and its final the scsi seagate is mine and it looks like im keeping it.ok so i bid on the scsi control card thats ldv and now im looking for a cable . my question does the cable need only one terminator? im new to this so if anyone can help me out on installing a scsi hd it would be greatly appreciated
 

A:scsi hard drive?

You want a 68pin internal LVD cable, it should either have a terminator built in + two connectors (one for the SCSI card, one for the hard disk), or three connectors + you'll need to plug a terminator into it. The devices should be arranged with the SCSI card at one end, the hard disk in the middle and the terminator at the other end. The SCSI card provides termination for its own end (unless you want to put the SCSI card on the middle of the cable, in which case you need a terminator for each end). The terminator must be LVD or LVD/SE compliant.
 

3 more replies
Answer Match 50.4%

My computer is not recognizing my SCSI 70 ghz drive. It keeps saying PXE-E61 failure check cable. It worked fine last night, I reformatted my secondary IDE 40 ghz drive and I could not get my computer to start. I had to disconnect my SCSI drive and setup windows xp on my IDE 40 ghz drive to get my computer to start. It still doesn't recognize my SCSI drive. I need help.
 

A:SCSI 70 ghz hard drive

This generally pertains to a bad hard drive or bad hdd cable same as a "non system disk error" with same solutions.
http://www.computerhope.com/issues/ch000229.htm
 

2 more replies
Answer Match 50.4%

Hi everyone,
I wonder if anyone have a good site where it can guide me on how to installed a second SCSi hard drive. I have a HP tc2120 server with one 36.4 Gb drive. I have anotherone just like that. But I never have installed and SCSI drive. I have only done the regular IDE drives. I need some help.

thanks,

AMD2800
 

A:SCSI HArd drive

9 more replies
Answer Match 49.98%

Hard disk type : Seagate SATA.
Model Number : ST3160215AS
Serial Number : 6RA1J7H0
Firmware Revision : 3.AAD

OS : XP SP3
Mother Borad : Intel 945 GCCR

My hard disk has passed Short DST and failed Long DST of SeaTools, do the hard disk going to fail? If yes, how to transfer my data to a new hard disk easily?

Complete description of the issue :

1.I have experienced boot up issue with my PC 2 days back. My PC not even boot into safe mode also.I got the following blue screen errors on successive restart of PC .

A. 0x00000050 ( 0xC374037F, 0x00000000, 0x804FBA19, 0X00000000 )
B. STOP : C0000135 ( Unable to locate component )
c. 0x0000007E ( 0XC0000006, 0X80698C12, 0XF79896E4, 0XF79893E0 )

2. I have removed and replaced the hard disk ( several times ). I can boot into windows now and can work normally, But,one of the above Blue sreen errors is coming all of sudden while working on PC. It is happening independent of the application I am using.

3. And the following messages are coming at the XP welcome screen and while working on the PC.

A.C:\windows\system32\drivers\etc\netloc.wlt has corrupted and unreadable. Perform CKDSK.
B.C:\windows\system32\drivers\etc\APPFCONT.DAT has corrupted and unreadable. Perform CKDSK.
C.C:\windows\system32\drivers\etc\idsflt.cfg.bck has corrupted and unreadable. Perform CKDSK.
D.Cagefile.sys has corrupted and unreadable. Perform CKDSK.

4.I have performed CHKDSK on all local drives exept local drive C. CHKDSK giving a message that " can no... Read more

A:My hard disk has passed Short DST and failed Long DST of SeaTools, do the hard disk g

In a Run box, enter "chkdsk /r"
You'll be asked if you want to run chkdsk at the next reboot. Enter "Y".
Reboot, and be prepared to wait, as it may take a long time.
 

2 more replies
Answer Match 49.98%

I am helping my brother in law out trying to do a non destructive repair using the installation disc. When we went through all the steps and got to the section that shows the hard drives it does not recognize the hard drive and won't let us do a repair. If we wanted to do a clean install it still would not recognize the hdd.
I decided to check bios and see what was recognized and in the hdd section it showed that the hdd was a SCSI. It is not a SCSI drive. We checked PC Wizard 2008 and it showed SCSI. All the places show that it is a SCSI. What is causing this? It is not a SCSI drive but a SATA drive. Can anyone tell me what has happened?
 

A:Hard drive recognized as SCSI

it is SCSI emulation. Some USB drives show up this way too.
 

4 more replies
Answer Match 49.98%

hello,

im going to setup a IBM Xseries 235 server in my home soon. I bought several drives. I noticed that one of the drives i bought is a scsi drive that runs at 7200k and the other drives run at 10000k. i bought two 7200k hard drives and 4 10000k hard drives. the server only supports raid 1. Would it be okay to create 3 raids. My computer supports up to six scsi hard drives. Can i create a raid with two 10000k hard drives to host my operating system and a little data, a second raid for my web server data and the third raid for my 7200k hard drives for ...idk, music.?

does that sound like it would work. would the 7200k hard drives slow down my computer?
is it possible to create 3 raids on a single server?
 

A:7200rpm scsi hard drive

bump
 

1 more replies
Answer Match 49.98%

I have a SCSI Hard disk, that i some how messed up by transfering it to a different controller, cuz i didn't know that you can't do that, i do now. i tried to get it to come back alive, by puting it back on the controller, but my master partion table thing got messed up, when i had tried to use it on the other controller, the first controller was a LSI Logic, and the second was an Adaptec 2490-UW. so i tried to use diskprobe to read the sectors and set it up like that, which failed. i thought it might have something to do with the board so i had taken that off, but now when i go into the Adaptec "SCSI-Select" program it doesn't show a size. could i have connected my board back up the wrong way?? it does still spin up, but i don't understand why it lost the size of the disk. it had the size before btw. it is a 18.2 GB 10K RPM SCSI-2 drive, and i have 2 other identicals if they may be of any help. but i really want to know if this drive is toast.
EDIT:: COMPAQ Model #: bd018734a4
 

More replies
Answer Match 49.98%

OK you SCSI experts, I've got a question for you. First, the particulars of my computer:

Dell OptiPlex GX110, 733mhz Pentium III, 256 Mb RAM, Adaptec AHA-2940U/AHA-2940UW PCI SCSI Controller with a maximum data transfer rate of 40 mb/sec., Boot drive is a SCSI IBM DCHS04W (4.50 GB) 7200 rpm with maximum data transfer rate of 40 mb/sec. and average read seek time of 7.5 ms.

Now, I just purchased a Fujitsu 18.2 GB, 10,000 rpm, SCSI hard drive, with a maximum data transfer rate of 80 mb/sec. and average read seek time of 4.7 ms.

My question: Will I benefit from the speed and efficiency of the Fujitsu drive by making it the boot drive?

I know that my SCSI controller card will limit the maximum data transfer rate to 40 mb/sec., despite the 80 mb/sec. rating of the Fujitsu, however, will the 10,000 rpm and the low average read seek time of the Fujitsu overcome the limitations of my SCSI controller card to the point that I should make the Fujitsu my boot drive? Thanks in advance for any assistance.
 

A:SCSI hard drive question

I will tell you this... going from 5400rpm to 7200rpm spindle speed makes a major difference. So going from 7200 to 10000 will make a difference.

For me, the decision would be easy. I would put the fujitsu as my boot drive.

It's a bigger drive and it's has better access times.
 

3 more replies
Answer Match 49.98%

On all internet vendors, I find sections of these 10k,15k RPM drives, called SCSI, and I have absolutely no idea why they are different to SATA/PATA. If they are just super fast hard drives, I'd buy 4 and link them in a RAID array, but I still don't understand the different names. It's a problem that has been needlessly bothering me for ages!
 

A:SCSI Hard Drives, What on Earth...?

scsi is a interface that looks more like pata than sata, but you will need a scsi adapter card or a scsi header on your motherboard, and even if you want to spend the huge amount of cash for a 15k hard drive you will not be able to utilize all of it because the your optical drive wont be able to keep up with the hard drive, i would stick with pata and sata both for cost and it (seems) that is what you know about, scsi is a whole different world than ide and sata
 

4 more replies
Answer Match 49.98%

Does anyone know of a website that I would be able to find the drivers for a scsi hard drive? I have been searching for what seems like weeks now and can't seem to find anything.

A:SCSI Hard Drive Driver?

The driver you probably need is not for the SCSI "drive" itself. It's for the SCSI "host adapter" to which the drive is attached.

Please give brand/model specifics of your machine... laptop or desktop (probably) and type/model/details, SCSI drive (internal or external), SCSI host adapter to which the drive is cable-connected.

thanks.

5 more replies
Answer Match 49.98%

I have a Win2k3 Small Business Server being ran with RAID on 4 hard drives.
1 hard drive just got failed and i replaced it with the "same looking" hard drive.
When i plug in the new hard drive i noticed that it does not match up to the others in size and its not meeting the requirements in size to rebuild.

When i looked closer at the hard drive i noticed the following difference from the other 3 working hard drive and the 1 damaged one:

Part: 9v8006-001
Firmware: e302

The model and brand are the same exact settings but non the 2 noted pieces of information. Do you think this could cause a problem if this 1 hard drive was different from the others?

Just wondering because i never had this happen to a SCSI drive on RAID settings, and yes its set to be auto hot swappable and ready to rebuild RAID - its just not working because of the size..........so it says.
 

A:SCSI Hard Drive Question

You should be able to use it. If that hard drive is slower then the other, it will slow them all down to match it, and your hard drives will only use as much space as is in the smallest drive. That is the way it works with conventional hard drives anyway. I would back up your data if possible first before you try it (if you haven't already), just in case.
 

1 more replies
Answer Match 49.98%

I just picked up this old server for nothing it's an IBM x240 2X9gig and 2x76gig Scsi and i wanted to try and get it going, not as easy as it sounds.

I got the drivers and the serverRaid disk from IBM and loaded the drivers onto a floppy, placed the 2k3 server disk in hit f6 and loaded the scsi drivers all was good.

Then an error saying i have no hard disk installed came up cancel the installation hit f3.

What have i done wrong?

This is what comes up during the post.

At startup Current memory configuration is not optimized
Adaptec aic-7897 scsi bios v2.20

Press Ctrl-a for scsi select utility
ch A Scsi ID: 5 IBM Ultrium-TD1 Ultra2-se

SCSI bios not installed

IBM serverRaid Bios
Bios Version 7.10.18

1 ServerRaid-4H Slot 4, drive configuration takes up to 5 minutes

Press Ctrl-I to enter mini configuration program

2 beeps

And then it ask me to insert a disk and hit f1

Any help appreciated
 

A:Loading Scsi Hard drives

6 more replies
Answer Match 49.98%

I've been trying to setup a Dell poweredge server I have just got, and am having huge problems getting it to recognize any of the 4 SCSI hard drives I have in it. I've trailed through the BIOS and so far have found, when SCSI devices it can find the drive in port 0, if I go into the RAID array to put this hard drive into the raid setup, there are no drives. If I boot all the way through to the install for the Linux distribution I'm going to install, no drives are found to install on. I've tried running the open manager server assistant CD to no use. I've tried installing a bootable floppy with SCSI drivers on it only to be told it's not a bootable disk.

I'm at a loss and nearly at the point of accepting defeat and buying new hard drives. Surely there is something really basic or obvious I am missing?

Help or suggetsions or rational thinking would be a blessing. Thank you.
 

A:SCSI hard drives not detected

Can we get a little more information about the model of dell server, and the size and type of scsi harddrives? I tend to not think it is the drives, I work with dell servers all day at my job, and usually it is either software crap, or a different piece of hardware has failed. what RAID controller are you using?
 

2 more replies
Answer Match 49.98%

I added a new 36Gbyte Fujitsu SCSI disk to my system. It already had a 9.1Gbyte Western Digital as the "C" Drive running win98se. The controller is an Adaptec AHA-2940W/AHA-2940UW PCI SCSI device with driver "Microsoft V2.21a 4-23-1999".

Using my win98 or DOS commands, I performed the fdisk and format E: /s (D was a partition on the original drive). Everything appeared to be good, I was able to load the new Windoes XP Pro software on the disk and performed multiple reboots in the process. Here is the problem! Once you power cycle the system, the new disk is not recognized as "ready" by the SCSI Controller and all the configuration appears to have been destroyed! Please help!

 

A:Solved: SCSI Disk Loses configuration after XP Pro Install and power cycle.

16 more replies
Answer Match 49.56%

I am about to build my own PC. It will have a Maxtor Sata hard drive. When you are installing Windows XP Pro, do you have to press F6 and install a third-party driver? I was reading this book, and the guy said to do that. I have never heard about that before. Can you just hit install XP and let it do everything? Thanks.
 

A:Installing Windows Hard Drive SCSI

Yes you need to hit F6 to install a RAID driver. You will be able to get that driver from the motherboard manufacturers website in most cases. The resulting RAID driver that you get will need to be on a floppy, so if you were planning on not putting a floppy in the computer you were building (like many do), you will have to at least have a floppy during the setup process of Windows. Sorry, theres no magic "hit install XP and let it do everything"
 

5 more replies
Answer Match 49.56%

Gigabyte GA-6LX7 Mb, 400 MHz celeron, 64 meg ram, 13.6 gig Maxtor ide hard drive, 9 gig Seagate scsi hard drive, win 98 se, DTC 3502A scsi adapter, Toshiba scsi cd-rom.
My scsi cdrom works fine, but. I can look at the scsi hard drive in windows and it says that it is only 19.2 meg, I can't access it in windows or dos. The on-board bios for the adapter doesn't find the hard drive or the cd-rom, but, I can still access and use the cd-rom drive.
Also, with ASPI3520.SYS enabled, the adapter and the primary and secondary ide controllers are disabled in device manager, it also makes A: drive use ms-dos mode compatibility.
I used the setup mode of the adapters BIOS to format the hard drive, After it formatted and I continued it says that it can't find a scsi hard drive.
 

A:SCSI Adapter/hard drive problem

Did you run FDISK and see if the drive is visible there?

Are you sure you have your SCSI termination correct?

If there are 98 drivers for your card you shouldn't need to load a driver file in the CONFIG.SYS - as you have seen it will put you in compatibility mode if you do.

Just checked the DTC site - it says:
<BLOCKQUOTE><font size="1" face="Verdana, Arial">quote:</font><HR>Windows 98 Drivers

Included - Use built-in Adaptec 151x/2x drivers <HR></BLOCKQUOTE>

Is that what you are using?

------------------
Get free stuff and help out a poor computer tech
(5/20 new, unlimited, pay to surf site added):
http://www.rkfdcore.com/ebaypics/referrals.htm
 

3 more replies
Answer Match 49.56%

As per the norm, I got a Monday call from a customer freaking out about their server. I paid them a visit and sure enough the Western Digital SCSI hard drive I replace about 6 months ago is dead. SCSI utility is seeing it as a 1MB quantum. I told them to boat anchor that machine and get a new one. It's a pentium (i don't remember) 600MHz machine so it's a bit of a dinosaur anyway. their book keeper is the hero of this story. I taught her how to backup the server which she did before she left on Friday. I loaded backup files on an unused workstation, mapped some network drives and had them back up and running PDQ.

What would make a machine eat hard drives? Thin it might just be a fluke, virus, inferior Dell product??????
 

A:2nd SCSI hard drive failure within 1 year

Is there a UPS or surge-protector installed between wall-socket and PC?
If not, unstable electricity might cause that, such as spikes, brown-outs or black-outs.
Or the PSU might be on the edge of its capacity. If the HD is a 10'000 RPM disk, they need a pretty good and stable PSU.
The disk should still be under warranty.
 

5 more replies
Answer Match 49.56%

I have a Dell Precision 530 and I would like to replace the two SCSI hard drives (Win XP OS) with two IDE hard drives instead with Win XP as the OS. Can anyone tell me how to go about doing this? Should I just do a clean install of Windows XP on the IDE drives? I know that the SCSI controllers are difficult to deal with.Are there any specific settings I need to enable/disable in the bios/setup before attempting to do this? I intend to completely remove the drives and the SCSI connector cable from the machine if I can get the IDE drives to work.

More replies
Answer Match 49.56%

Long story short.. An office I help out had a RAID Array crash without a backup. The data has been recovered and is sitting on a Fujitsu Hard Drive (Model: MAX3036NC).

My computer, and the remaining working computers in the office are all IDE or SATA architecture.

I'm guessing there is a PCI SCSCI Card that I could buy, install this hard drive and access it that way. If that is the case, could someone recommend a card/manufacturer that would work for this case?

Any help is appreciated.

Edit: We also have a laptop available if there is a PC-Card solution.

Thanks,
 

A:Solved: Need to access a SCSI Hard Drive

6 more replies
Answer Match 49.56%

Just tried to install a SCSI hard drive on a win98 system.

Drive is in Device Manager but has no Letter assigned. Does not allow me to.

BIOS recognizes drive and assigns D:
 

A:SCSI Hard Drive - No Letter Assignment

7 more replies
Answer Match 49.56%

Hello all,

I have an HP Workstation XW8200 running Windows XP SP3 that I tried hooking a projector to. I used a VGA splitter with one out going to the monitor and the other going to the projector. When connected while the computer is already running, the projector works. But once the computer is off, with the projector connected and running, and then the computer is turned on, it no longer recognizes my hard drive.

This problem is NOT fixed when the projector/splitter is disconnected.

In the BIOS, the hard drive is recognized but it will not boot. I tried booting into a Windows XP disk and running recovery mode, but it doesn't see the drive. Same goes for booting off of my thumb drive into Linux (Lucid Puppy 5.2.0), it does not see that I have any hard drive installed.

This has happened to two computers already, both are the same model and setup.
The hard drive in question is connected to onboard SCSI, and is a SeaGate Cheetah, I'm not quite sure what size.

I did take another hard drive from a third HP XW8200 and put it in to the non-working computer and it booted fine.

I do not see the projector causing the computer to not recognize the HD, but it definitely seems to be the catalyst for both of these computers (with each individual problem happening months in between, and over a dozen other similar computers still working fine).

Any help would be greatly appreciated, I'm at my wit's end.
Thanks,
L_C

Oh, and there are no error messages when trying ... Read more

More replies
Answer Match 49.56%

hi my new sata hard drive is showing as a scsi in win7
and it seems to be running slow and making alot of accessing data noises
how can i fix this back to sata
thanks

A:new sata hard drive showing as scsi in win 7 help

With some hard disk controllers it is normal for it to show up as a SCSI disk - particularly if the disk controller is running in AHCI mode, which is preferrable since it allows features such as NCQ. One thing you may want to check is: locate the drive itself under "Disk Drives" in device manager and go into the properties. Select the "Policies" tab and view what is set. For better performance you will want it set to "Better Performance" with both of the boxes checked. Though if you lose power you may run into minor file corruption issues - I personally have not had issues with this. If you disable those check-boxes performance can decrease significantly.
 
-David Betournay

1 more replies
Answer Match 49.56%

can some help me,i am trying to install 2 4.5 gig SCSI hard drives in windows 2000 .i an useing pci scsi card controller.
i load win 2000 boot disc,s my system finds scsi,s no problem
i format them and partion them .when it reboots to start loading windows it say cd rom error ! INSERT BOTT DISC AND RUN AGAIN
any body got any pointers...

thanks ....rog
 

A:two scsi hard drive install in win 2000

8 more replies
Answer Match 49.56%

How can I test disks that are 68 PIN SCSI?
I have a SCSI controller but it takes a different connector.
Can anyone shed some light?
 

More replies
Answer Match 49.56%

*RESOLVED* Can't install second U160 SCSI hard drive

I have DL145 G2 from HP
http://h50043.www5.hp.com/Enterpris...nt/questions.aspx?cnty=th&cat=DL&ser=145G2#g1

On the black thing that is attached to the cable which seems to be a controller, it says U320. It originally came with U320 SCSI hard drive but I purchased two U160 hard drives because I was a *****. I connected one U160 SCSI hard drive to the server and installed windows os without any problem. But when I tried to connect the second SCSI U320 hard drive, it didn't work. In the BIOS, it correctly recognized two hard drives but when windows 2003 server loaded, I couldn't see or install the second hard drive. I read some FAQ in the link I copied above and I thought that I have to purchase optional SCSI cable or my U320 SCSI cable only supports one U160 SCSI hard drive or something... But I don't see any place to plug any more cables on the motherboard so I'm really puzzled...

I use two SEAGATE ST3146854LW 15K 68 PIN U160 DELL M6616
and my server is DL145 G2 AMD Dual-Core Opteron 275 2.2GHz 390845-001
 

A:Can't install second U160 SCSI hard drive

So the BIOS sees both the drives?

What do you mean by Windows not seeing the hard drive? You did check in the Disk Manager, right?

SCSI is pretty much backward compatible, so your U160 drives should work no problem. And you can hook up 15 of them to a single SCSI cable no problem.
 

8 more replies
Answer Match 49.56%

How do I get Windows XP Pro to duel boot from a second scsi hard drive. First scsi hard drive has Windows ME and works fine.
Second scsi hard drive has Windows XP pro but only works when I change the scsi ID from 1 to 0. But then the other scsi hard drive is not reconized in windows explore. However, it is reconconized in the XP disk manager and everthing else appears normal excapt that the drive is not read in explorer. Any help PLEASE
 

A:Duel Boot XP on second scsi hard drive

Was XP installed with both HDs in the machine, and with Me installed first? If you installed XP with only its HD in the system (so it was 0 when you installed it), the XP boot files are on the wrong hard drive. They need to be on the system's primary partition, which should be C: (where Me should be now if this is going to work right and properly dual-boot) and the ARC path in your boot.ini file is referencing the wrong disk for the XP startup to look on to boot XP when you have both disks set up.

Please post the contents of your boot.ini file here, and we will take a look.
 

1 more replies
Answer Match 49.14%

Windows XP sp2 wont boot from hard disk.

After much to do turns out my computer doesnt recognise the hard disk.

I have a seagate 500Gb SATA hard drive, its about a year old, the computer doesnt get hot in the slightest and it shouldnt be dead. I checked the wiring, as far as i can see, its all fine.

only conclusion i come to is that my hard disk is kaput which it shouldnt be. Can anyone give me any other possible solutions to try out before i cry and/or spend money on a new one? theres a lot of data on it i dont want to lose.

If not, ill plug it in to another computer to check, i havent done that yet because it will take me hours - i can only unscrew the hard drive from one side without rearranging the room.

ty!
 

A:Hard disk boot failure -> computer won't recognise hard disk

Is your Seagate the 7200.11 series?

We've been seeing a lot of harddrive issues layely that has nothing to do with the drive itself but bad SATA cables aas the cause. Do you have another one you can switch out?

When you say the computer doesn't recognize it we're talking the BIOS here, correct?

Another suggestion is what you have already suggested but I would "slave" it in antother system and see if you can access it that way.
 

5 more replies
Answer Match 49.14%

Greetings,
 
I have an Asus laptop running windows 7 64 bit and this laptop came with 2 hard drives, each partitioned into two parts (C:\ & D:\ and E:\ & F:\).
 
I am transferring over 30GB of data from one drive (C:\) to the other (F:\)
 
Get this... the transfer rate is 1.2MB/s right now. Over 9 hours left to copy the 30GB. There are over 125,000 items but that still does not justify the 1.2MB/s
 
I am open to any suggestions but first, a few points.
Yes, I am sure they are two separate drives with those partitions.
Error checking showed zero errors on both drives.
This is the 3rd time I am trying a transfer.
Both drives are relatively empty (especially the F:\).
C:\ is my system disk.
The SMART data shows no read/write errors or overheating.
I have disabled the virus protection and all real-time scanning.
 
Again, I am very open to suggestions and checks. Feel free to post your idea!
 
 
Thanks in advance!

A:Laptop Hard Disk to Hard Disk transfer Extremely Slow

My experience with file transfers of the type you describe...is that the number of files doesn't matter...what matters is how large the files are.  Video files take much longer than text or document files.
 
Slow transfer rates between partitions/drives...can indicate a problem with either the partititon or the drive, IMO.
 
Please download MiniToolBox  , save it to your desktop and run it.
 Checkmark the following checkboxes:  List last 10 Event Viewer log  List Installed Programs  List Users, Partitions and Memory size.
 Click Go and paste the content into your next post.
 Also...please Publish a Snapshot using Speccy - http://www.bleepingcomputer.com/forums/topic323892.html/page__p__1797792#entry1797792 , taking care to post the link of the snapshot in your next post.
 
Louis

2 more replies
Answer Match 49.14%

Hi guys,

I will try to explain this as simple as i can.So let's start
I have laptop ASUS N75SF and it is a year old,so i have decided to format.I have two separate hard disks that are the same brand,SeaGate 9500423 AS, each 500 gb capacity. Before i decided to format , one of my hard disks(that is my partition D) started to make strange noises and it was not recognized,but i was using my laptop without problems because my windows was installed on my other hard disk (that is my partition C).So now my question is this :
After i formatted them both i have no clue which one is which ? they are like :
Disk 0 Partition 1 465 gb
Disk 1 Partition 2 465 gb
So how do i choose the one that is better and not having problems to pust my winodows on?
I know that i can buy new one and replace it with the one that is having problems,but right now i have no money to do that .I am student

Thanks in advance

A:Confused about installing Windows on my hard disk,hard disk problem

I'm willing to bet that Disk 1 is the bad hard drive since the bad hard drive was the D: drive.

6 more replies
Answer Match 48.72%

Hello, this is my first post here. I have an HP Workstation x4000 I use at work for Designing CAD Models. This is an old computer. My problem is that I am out of room on the Hard Drive. It is a 58 GB SCSI,68pin HP Hard Drive. My IT support guy purchased me a 1GB SATA Drive,Raid Card,enough Memory to fill the MEC Card, and Norton Ghost to flash over the new Drive. My problem is, the Card he bought will not fit into the Mobo. The ribbon in the Computer has an empty plug and a power plug,but they are for a 68 pin SCSI Hard Drive. Is there a cable made that I can use to simply plug the SATA Hard drive into the 68 pin ribbon,or do I need a card? Do they make such a thing? My boss is extremely frugal and doesn't want to hear that the best thing would be to replace the 12 year old computer! Thanks for any help you guys can give me
 

More replies
Answer Match 48.72%

I have a Dell Tower Computer (Circa 2000-2002) that runs RIP software (Raster Image Processor) used to send graphics/image data to a machine that makes by way of laser imaging our plates or masters for our offset printing presses. Monday the hard drive failed. The Dell has Windows XP license decals on it but when booting up it display Windows 2000 NT. The computer has only 1 hard drive, a 68 pin SCSI drive and the cable to it connects to separate dual channel SCSI card which is in a slot on the motherboard. There is another SCSI card (single channel) in the slot next to it which has a cable that goes to the machine that this computer drives. The software that runs on this computer is proprietary software and I have a re-install disk for it being send via UPS Next Day Air as I type. I have an XP disk & license that I can install on what ever hard drive I can get to work here and the RIP software manufacturer said their software would work on XP. But I don't have a copy of Windows 2000 NT.

My question is that if I can't find this same hard drive locally, can I use an IDE or a SATA hard drive instead and still run the RIP software correctly? There is 2 IDE (primary & secondary) connectors directly on the motherboard. One is used for the CD rom drive, the other is unused. I am not certain but I don't believe the motherboard has a SATA connection. I have 2 good spare IDE hard drives.

If I can't make plates I can't print so I need to get this reso... Read more

A:SCSI hard drive died - can i switch to ide or sata?

8 more replies
Answer Match 48.72%

Ok I have a external enclosure that is IDE / Sata , I have 2 hard drives I'm not using , there both SCSI 10,000 rpm Hard Drives, my question is how can I connect one of them to my external enclosure so I can connect em to my USB

A:Connecting SCSI Hard Drive to my external enclsoure?

You cannot do that. Your drive which is SCSI will not connect to an IDE/SATA controller in the external hard drive enclosure.

4 more replies
Answer Match 48.72%

Hello All,

I just got my hands on a Compaq 36.4 gb hard drive (10k RPM). It has an scsi port connector but I don't know how to connect it to my ECS board which is fairly new (one of those SLI-status boards). I might need a converter of some sort. The hard drive model is: BD0366459B , my board model is ECS 945-p ( http://www.digit-life.com/articles2/mainboard/ecs-945p-a-i945p.html ) .

Thanks ahead of time.
 

A:Hard Drive Compatibility?:confused: SCSI to IDE or SATA?

According to this site
Product Name BD0366459B
CD-ROM Drive Compaq CRD-8402B
Hard Disk Drive Compaq BD0366459B; 9.09 GB; Firmware 3B12; Wide Ultra3SCSI
BD0366459B; 145. GB; 291. GB; Firmware B005; Wide Ultra3SCSI
Host Bus Adapter Compaq Integrated Dual-Channel Wide-Ultra SCSI-3 ControllerClick to expand...

You need

(1) a SCSI-3 controller to be installed into the mobo
(2) a Wide Ultra3SCSI cable

You may get the hard disk cheap but could get rip off by the hardware needed to go with SCSI equipment.

The Sata can be viewed as a poor man's SCSI but at least your mobo support 4 units out of the box. I doubt if a SCSI can be cheaper than Sata nowadays which is being retailed at GBP 0.128 per Gb. Thus the 36.4Gb unit would cost no more than GBP 4.65 in UK which, if being a Sata disk, is equivalent to approximately one imperial gallon of petrol. That amount of money will not be able to buy either one the above two attachments required to run the unit.

Technically if you run a Sata Raid 0 to half the access time it should beat the SCSI disk performance hand down, I would have thought.
 

1 more replies
Answer Match 48.72%

I have been trying to determine which device would be best suited for cooling a pair of SCSi 15k HDDs. I have been looking around at some of the following (in order) of interest. Sound dampening is not a huge concern, mainly concerned about cooling.

Smart Drive 2002 Copper Hard Drive Enclosure- SCSI compatible? Little documentation to indicate if rear is already equipped with wiring or is this will work with SCSI cables?
AEROCOOL HB-101 Hard Drive Cooler Aluminum- Wondering if this is a gimmick or a real option... or a SilverStone SST-FP53-B 5.25" Hard Drive Cooler or a Cooler Master CoolDrive 3... ??? Any other reccommendations based on experience or reviews? Thanks in advance for any help.
 

A:NEED serious advice about Hard Drive Cooling (Pair of SCSI 15k)

if you haven't already bought a case, buy a case with a hard drive cage fan and put it to use. for internal enclousures, all same size drives and cages are compatible. just make sure you have cool air blowing on those drives and they should be just fine.
 

2 more replies
Answer Match 48.72%

My first build: Via Kle-133 mb with Athlon 700 and 64 sdram
on board video and sound and 9gig Seagate Hard drive needing a scsi-2 thingy

My problem...
I power up and all things begin running and on the monitor it whizzes past the first screen that reports the "Award Modular BIOS v6.00pg, An Enery Star Ally etc...
Main Procecessor: AMD Athlon (TM) 700MHZ
Memory Testing:57344 ok + 8192k Shared Memory

Primary Master: None
Primary Slave: None
Secondary Master: Toshiba CD_ROM XM-5602B 1796
Secondary Slave: None

Floppy disk(s) fail (40)

Then immediately a black screen which says
BusLogic Inc BIOS Version 4.94G
Intelligent Bus Master SCSI Host Adapter
(c) 1995 BusLogic Inc. All Rights Reserved

BusLogic PCI SCSI Host Adapter Firware Version 4.28D
Press <Ctrl-B> to Enter AUTO-SCSI

Which I do the <Ctrl-B> thing and it takes me to a configuration Utilities and Diagnostics program. I try to push the right buttons
Under Utilities and under SCSI Device Information it says
SCSI ID 3: SEAGATE SX910800N
SCSI ID 7: BusLogic BT-946C
(which makes no sense since the hd is a Seagate st410800N)
Under Verify Disk I get the same result

OK then I try the Format Disk option
and the same exact result box comes up with SEAGATE SX910800N highlighted... when I press enter, it asks: CONFIRM? yes or no, I highlight yes and enter and then.... a freeze.

Now if I reboot it will do the same thing every time.
If I ignor the Press <Ctrl-B> to Enter AUTO-SCSI thing, the puter will g... Read more

A:New computer built hard drive with scsi problem

11 more replies
Answer Match 48.72%

SCSI vs SATA vs EIDE
What are the differences between all of these?

I'll probably not use SCSI, but I was looking at the WD raptor 10K rpm hard drive (SATA). Do you need a special motherboard or certain controller to run this hard drive? And do you need a special CABLE for it? I have tons of 80pin IDE cables, but those wouldn't work?

Thanks
 

A:HARD DRIVE question - SCSI vs SATA vs EIDE

Nope won't work. Different drives, cables, controllers. Some motherboards now come with the SATA interface built in. For more information check this site out. Its an OLD report on SATAs. Hard drives are now available for SATA use.

http://www.explosivelabs.com/articles/sata/
 

2 more replies
Answer Match 48.3%

Hi I have an old proprietary graphics system that needs a SCSI hard drive, I found a Compaq C2247 1gb hard drive that should work (cylinders,heads,etc match one of its table drives) but it doesn't turn itself on when the PC is powered on.

The drive works perfectly in my new system as long as I have the "send power on signal" checked in the bios.

Is there any way of jumpering this drive so it turns on the instant power is applied as opposed to sending a signal to tell it to turn on?

Thanx
Ryan
 

More replies
Answer Match 48.3%

How do you get the power to your hard drive. The power supply has no extra wires or anything. Where does it come from?
 

A:{SOLVED} im a begginner, installing a new hard drive (scsi) so this may seem silly,

8 more replies
Answer Match 48.3%

This is my first attempt at building my own pc so forgive me if this is a silly question.

This pc has an SCSI as the primary drive (17gig) and I'm trying to add two 320g drives that are edi drives.

I added a new dvd drive, video card, and usb 2.0 card and those all work fine.

I tried the drives set to slave as well as well as cable select. I even removed one of the drives so that the only connector is the edi slave connector.

Am I having a problem because I'm trying to use an SCSI drive and the two edi drives? Do I need to use one or the other in order for this to work?

Any help would be greatly appreciated.

Let me give a little more information if it helps. The computer is a Dell Precision 530 Workstation. Company upgraded all their pc's and sold off the old ones for $50 each. I want to ue this as a media server for my home network.

It has a 17GB SCSI drive on it now that has my Windows XP Home Edition and a few other programs on it. I was going to keep it for exactly what it does now. Basic everyday pc duties.

I wanted to add two bigger drives for storage. The mother board has an SCSI connector and two EDI connectors. The secondary EDI connector is connected to the DVD drive and the CD drive. Obviously I don't need both but just left the cd drive in there since it wasn't hurting anything. Those both read and work fine.

I have the two 320 GB storage drives connected to the primary EDI connector.

The ribbon cable attached... Read more

A:PC won't recognize extra hard drives (edi) primary is SCSI drive

Hold on a minute... edi you mean IDE or eIDE don't you?

SCSI hard drives need to have terminated cables. IDE cables do not use termination. I would ditch the SCSI, but you will have to get into the bios settings and change the primary boot drive settings
 

8 more replies
Answer Match 48.3%

This may be the wrong forum if so please redirect me. I have a pair of acoustical home theatre speakers. 27" x 15" x 12" with a 10" woofer with high tempered voice coil, bullets super tweeter and piezi driven horn. How can I determine the watt output? I don't know if it is 340 or 1000 peak.
 

More replies
Answer Match 48.3%

Acoustic Authority CPU speakers stopped working

My Acoustic Authority speakers stopped working around the time that I messed around with the sound enhancement options in Control Panel > Sound > Speakers > Enhancements and I highlighted the bass boost and low frequency protection, room correction, and loudness equalization. Now have you heard of these options ever having adverse or negative effects on Acoustic Authority CPU speakers? No sound options are muted, sound card is also kicking out sound to speakers.
 

A:Acoustic Authority

Do these speakers have built in protection circuitry? Excess EQ can cause extreme power demands which could possibly trip the breakers (relays).

Are you sure you didn't accidentally "retask" one of the output jacks in your resetting frenzy?
 

3 more replies
Answer Match 47.88%

I am having this Hard Disk problem. My old Hard Disk (Samasung 500GB) (bought in 2010) started showing signs of corruption (like Windows doing chkdsk at every boot, and data getting lost). So I bought a NEW Hard Disk (Western Digital 1TB) last month (Sep 2016) to backup all the data from old one. I didn't have time to backup but wanted to use PC so I Clean Installed Windows 7 64bit on the New Western Digital 1TB and used it about a month without any problems.
 
A couple of days ago i decided to backup up the data. I reformatted the New Western Digital 1TB with Gparted and did a clean Windows 7 Install again. I connected the old Samsung 500GB to the motherboard and started copying the files to the new Western Digital 1TB.
 
Suddenly Windows showed me an error "Windows detected a hard disk problem" which makes sense because the Samsung 500GB is old and might be failing BUT the error is showing both of my Hard disk in the dialog box.
 
Is my new hard disk corrupt as well?
Why is Windows showing my new hard disk as failing?
Can Windows mistakenly show both hard disk in error?
 
Please help i am confused. sorry for a confusing question. i will answer anything required.
 
I have taken the screenshot of the error message, they are in attached files.
1)The 1st Screenshot shows both my Hard disk in the error box (OLD Samsung and NEW Western Digital WD)
2)The 2nd Screenshot shows only one of my Hard disk and its the new one (Western digital WD)

More replies
Answer Match 47.88%

What is the difference of 3.5 external hard disk (e.g. WD My Book) vs a 3.5 internal hard disk fixed into an enclosure to work like an external hard disk?

Are both good to be use as an external drive to store backup?

What 3.5 enclosure is good?

Thanks

A:3.5 external hard disk vs 3.5 internal hard disk with enclosure?

What do you mean fixed into an enclosure to work like an external drive? Are you referring to a My Book 3.0 VIA USB 3.0.... vs.... an internal SATA III SSD or HDD? Be a little more specific.

8 more replies
Answer Match 47.88%

i have a 80gb internal hard disk since it was not sufficient i switched up to a 500gb hard disk so i want to know whether i can use my 80gb hard disk as an external hard disk
if so how please instruct me
 

A:how to change a internal hard disk to a external hard disk

Is the 80gb drive ide or sata?
 

3 more replies
Answer Match 47.88%

Hi..im new on this forum and i have a problem with my old hard disk..every time i turn up my pc, windows pop out message ""Windows detected a hard disk problem" ,"Back up your files immediately to prevent information loss". So i decided to replace my old hard disk, but problem is that i have vista preinstalled on my old hard disk. So my question is how can i install vista from my old hard disk into my new one?..please help me and thank u for your reply

A:how to install preinstalled vista from the old hard disk into the new hard disk?

hi check out this first http://forums.techguy.org/hardware/7...e-failure.html just in case and if you do need to read this http://en.wikipedia.org/wiki/Disk_cloning

6 more replies
Answer Match 47.88%

'Lo All,

I need to upgrade the HD space on my PC here, and was wondering if it'd be worth it to convert over to a couple of those shiny new 15000rpm SCSI drives (If it's pertinent, my motherboard is an Intel 875 / 2.4ghz and both hard drives are 18 GB 7200 rpm IDE's). A couple of quick questions:

1. Do I need a SCSI controller (the ones that I see selling on Pricewatch for about $25) to plug the "new" drives into, or is there a way to get them to work without this?

2. Is this even worth it; that is, will I see an appreciable increase in system performance once I've made the jump from 7200 IDE --> 15000 SCSI?

3. Anything else I should know about this whole scenario? Ostensible pitfalls/perks/etc.?

TIA for any responses...

P.S. I'll pre-empt any, "Newbies shouldn't mess with the inards of their computer"-style responses by stating that a friend will be doing the actual install/setup work...
 

A:Switching from IDE --> SCSI hard drives on home desktop...good idea?

the newer scsi run at 360 this means faster access
you will need a card that handles this speed plus the cables
price has come down some still very xpensive almost $2.00 USD a gb
SATA is cheaper and is almost as fast ,in most cases you will not see diff.
I think sata's run at 180 ( I dont use sata)
iede run at 133
warrentys on both are bout the same from 3 to 5 years
both support RAID most sata cards have this included
scsi cards don't you have to pay for that feature
if MB doesn't support sata you will need a card for it
only invest in scsi if you have critical systems and or run very intense app's
so if you want to upgrade and keep cost at min. go sata
if you are not up to task of boot issues with sata stick with iede 8mb cache 7200 rpm (I perfer Seagates)
 

8 more replies
Answer Match 47.88%

Hello,

I have a BIG problem here with a SCSI drive on our web server in our school.

All of a sudden i keep getting Start Unit Request Failed at start up.

and then when I try to verify the HD on the SCSI menu I receive an
"UNEXPECTED SCSI COMMAND FAILURE" with above a SENSE KEY: "NOT READY".
Like it says, it's not ready.

now this is the secondary hard scsi disk, my primary bootup disk is fine, when i boot up windows, it boots up fine, but doesnt see the e: drive. in device manager though it is there and it says it is working properly.

Do you think it could be the hard disk has failed. only last week on this same server the power supply went. and we changed the power supply. could thsi be related?
Thanks

Ranj
 

A:SCSI hard drive problem. Start Unit request failed.

Try reseating the connectors to the drive. You might swap the power connector between the two drives. Maybe something was bumped when the power supply was removed. If that doesn't work then probably the drive has failed. I take it that the secondary drive is on the same cable as the primary one and it was working ok before the supply went?
 

1 more replies
Answer Match 47.88%

Hello all. This is my first post here. I Bought a scsi hard drive.

Maxtor 18GB SCSI Hard Drive
Formatted capacity: 18.4GB
Interface: Ultra160 Wide LVD SCSI-3, 80-pin (80 to 68-pin SCA adapter included)
Rotational speed: 10,000 RPM
Average seek time: 4.7 ms
Cache: 8MB

I have the ASUS a7n8x deluxe mother board. What pci scsi adaptor card do I get to run the hard drive? What cable do I need?

This is my first time using a scsi drive. I did a search on newegg and saw a range from $22 - $400+. Please educate me in the ways!
 

A:Installing a scsi hard drive on an asus a7n8x deluxe board

Anything from Adaptec is perfect, but not always the cheapest.
It's what I use on no less than 3 of my PCs.
http://www.scsi4me.com/index.php?menu=menu_scsi&pid=213&display=39160.htm
Brandnew Adaptec ASC-39160 Dual Channel Ultra160 SCSI Controller, $139.-

http://www.scsi4me.com/index.php?menu=menu_scsi&pid=3237
Brandnew bulk LSI Logic LSIU160 single channel Ultra160 all purpose controller $35.-

They have a whole collection of others, as well as loads of information there.
You could try and pick up a used card on Ebay as well.

You will also need a 68-pin internal flatcable with a terminator.
Look around on that website.

Also go to
http://www.adaptec.com/worldwide/pr.../SCSI&prodkey=talk_about_scsi&type=Technology
for a bit of background.
 

2 more replies
Answer Match 47.46%

My new drive from Maxtor uses acoustic managment to quiet my HD. The problem with this is the fact that it slows it in order to quiet it. I would like to disable this feature but have ran into problems doing so. Hoping someone can help.

The only program Maxtor offers only runs from DOS (amset.exe). I only have NTFS partitions. I do have a program called NTFSpro 4.0 that is used to read/write to a NTFS partition in dos. However, when I try to run amset.exe, I get an error that tells me --> Invalid COMMAND.COM
Enter correct name of Command.com Interpreter (eg, C:\COMMAND.com) <---

I did try and point it in the right direction, and also tried to copy the file into my root directory, but still received the error.

I have searched all over, but can not find a program besides amset that will allow me to do this. Does anyone know a way around this, or another program that will allow me to change the settings in Windows xp?

Thanks, KK
 

A:acoustic managment and NTFS

6 more replies
Answer Match 47.46%

Is there any good software for Acoustic shock protection?
It's hard to have the same volume all the time because my son maybe
raised it last time and I didn't see... There's movies and games with a
very low volume while some stupid people out there is making movies
where the sound is destroying both your loudspeakers and ears!!!!

You maybe want to decrase the volume to hear what they say and suddenly
there's some "cool sound effects" that gives you a serious hearing damage or
tinnitus for the rest of your life!!!

I've got a serious tinnitus and I need something that keeps the volume down.

I think all software and hardware today should have some kind of protection
to prevent Acoustic Shock!! And skip the **** in-ear plugs!!!!

Take care
 

A:Acoustic Shock & Tinnitus!

No software or hardware can protect you from Stupid Users.

Also, AFAIK all consumer setups are pretty much "safe" in the sense that you cannot blow them up without doing some special rigging and they don't produce sound loud enough to harm normal people.

If you are sensitive to loud noise, make it a habit of always turning down the volume on the speakers/amplifier and then turning it up to a level suitable to you.
 

2 more replies
Answer Match 47.46%

Hi everyone,

I'm attemping to install Windows 7 64 bits in a Sony vaio SVE14A25CLB laptop. Many threads in this forum already help me a lot to change the UEFI settings to boot from a DVD or USB device in UEFI mode and I clean the hard drive with diskpart. Also secure boot is disabled.

My System specs:
Sony Vaio SVE14A25CLB
Intel Core i5 -3210M, 2.50GHz
Sony Vaio Intel HM76 Express Chipset
4GB DDR3 SDRAM 799MHz
Intel HD Graphics 4000, AMD Radeon HD 7670M 1GB
HDD 750GB, 5400 rpm

My next opponent in this journey is while windows setup is loading the files, on UEFI mode, it just stop at loading the disk.sys file (checked in safe mode), but in Legacy mode (BIOS) the windows setup (DVD or USB) start without issues (this is how I managed use diskpart).

I don't think it could be due to hard drive or memory issues (I didn't run any tests yet), as the windows setup start normaly on Legacy mode and It install successfully Windows 7 on a MBR partition.

From factory, the laptop comes with Windows 8, but even if the general performance is very good, it was some "features" that bother me. So hard drive already has GPT and I want to keep that partition table mode in case I need to do a dual boot with windows 8 in the future.

After clean the hard drive I even created GPT partitions following these steps:
Sample: Configure UEFI/GPT-Based Hard Drive Partitions by Using Windows PE and DiskPart (see Sample DiskPart Script: Default Configuration)

I ha... Read more

A:Windows 7 setup stop in disk.sys on UEFI mode, but in BIOS mode it did

Sony boot key is F12.

Make sure you have followed Option One in UEFI Bootable USB Flash Drive - Create in Windows
to create the flash stick.

To install Win7 in UEFI mode sometimes requires some level of CSM or Legacy set in BIOS, even "Boot UEFI First." You will need to scour those listings, post back camera snaps of all available choices for UEFI, Legacy, CSM, and boot order. Are you choosing UEFI device to boot. That would point to the media being the problem.

At Eight Forums they can help you derive your Product Key so that you can reinstall 8 to an MBR disk using media they should also be able to link you to. This is providing the BIOS won't auto-activate on MBR. These mysteries are all shrouded in EightForums which I will get over to one day when Win7 stops being the most popular OS and keeping us so busy here.

2 more replies
Answer Match 47.46%

This is a follow up to
http://www.bleepingcomputer.com/forums/topic403398.html

SweetTech just helped me clear out some malware and referred me to this forum when I ran into some interesting issues with Safe Mode:

1. I could not log into safe mode as administrator, it stalled at "getting personal settings". I am able to log on with as my regular user though.

2. In Safe Mode my C drive has 2 Gigs more of free space than in regular mode (is that normal? I though what's on the drive is on the drive no matter what mode I use...)

I have an HP Pavilion Laptop running WinXP SP3.

Many thanks for your input and advice!

A:Difference in disk space between Safe Mode and Regular Mode

In Safe Mode my C drive has 2 Gigs more of free space than in regular modeHow are you reading this , or from what program.I think this is only due to being in Safe Mode and in Safe mode you are not using all processes compared to Normal mode.Is the first item an issue for you, then you could have asked S /Tech during her help.Thank You -

7 more replies
Answer Match 47.46%

Today I wanted to intsall Windows 8 in dual boot envirnment with Windows 7 so I created a separate 60gb partition for Windows 8 but after the partition was created, all the previous volumes like Windows 7, HP_Recovry and HP_Tools and the newly created Windows 8 partition are now dynamic plus I can't install Window 8 on that dynamic partition. Below is current situation as shown in disk management in Windows 7:

http://jumpshare.com/v/X7ZGXD?b=G780N3 [Image link]

Please help me. I don't want to lose my data including the Windows 7, and HP_Recovry and HP_Tools partitions. Please suggest me clean method to go back to basic disk mode from dynamic mode without losing data. When try to convert from dynamic to basic using easeus utility, it gave me following warning:

http://jumpshare.com/v/07JNKj?b=G780N3 [Image Link]

Anxiosly waiting.

Muhammad Qasim

A:I want to Go back from Dynamic disk mode to basic mode in HP Probooks

any one reply please, I am in great great trouble

3 more replies
Answer Match 47.46%

I Installed windows on a ssd drive running in ahci mode. I then switched the sata setting in the bios from ahci to raid in order to add 2 other hdds as a raid 0. Now the pc won't boot anymore getting no boot device error. I know about the registry fix to get an IDE sata drive to boot in ahci mode, is there a similar solution to change a dire from ahci to raid?
Note the mb only has 1 controller so I can't have the boot drive in ahci mode with the other 2 in raid mode.
Thanks in advance.

A:Can I switch my boot disk from ahci mode to raid mode?

Hello Danag, and welcome to Sevenforums. What kind of computer do you have, or did you custom build it? Go to it's manufacturer's website and install the Raid drivers.

EDIT: set it to RAID after the Raid drivers are installed, it will be fine. Let me know how it goes

3 more replies
Answer Match 47.46%

Hi! I am running an Adaptec 29320LP adapter with 2 Seagate st336754lw 36gb 15k hard drives but the hard drive speed is maxing out at 70gb per second!! Does any one know how do i config to get the full 320 gb per second or at least close to????

Any help would be apriciated.

Cheers.
 

A:scsi U320 Speed problem for SCSI Wiz

Because the interface supports that speed doesn't mean the drives can actually sustain a transfer rate close to that. Same as with PATA and SATA IDE drives. But 70MB/s does seem low. Are the drives in RAID or just seperate individual drives?

Also how are you measuring the speed? Try HDTACH: http://www.simplisoftware.com/Public/index.php?request=HdTach
 

3 more replies
Answer Match 47.04%

I just moved my Philips Acoustic Edge soundcard to a new system and I seem to have problems. It was in a system with Win98SE, and the new system has WinXP Pro. When I benchmark using 3DMark2003, I can complete the test up to the final sound test, then it kicks me out with a message that the soundcard can't complete the test. I have the latest drivers from Philips running on the following system:

Pentium 4 2.8 800FSB
Intel D875PBZ 400DDR mobo
ATI Radeon 9700 Pro
WD 800JB HDD
WinXP Pro SP1

I also can't seem to run Max Payne. It will run the cutscenes, but reboot the system when the game starts. Probably not related to the soundcard issue, but thought I'd mention it.

Thanks for any help......
 

A:Philips Acoustic Edge Problems?

Does 3DMark2003 say why the soundcard can't complete the test? Have you tried running dxdiag's sound tests?
 

2 more replies
Answer Match 47.04%

I am attaching this speaker with my new motherboard machspeed model viperK8T8AS but I have no sound. I search tech support on motherboard and they said I should contact Boston Acoustic since the speaker is having problem with the motherboard. I went to Boston Acoustic site but they are no help either.
Anybody have anyidea how I can get this speaker to work? The motherboard comes with sound card(all in one mother board).

Thanks
 

A:Boston Acoustic Model Ba735

The Digital BA735 is a digital only system, and requires a properly set up digital sound card.

Your motherboad sound is analog.

So it cannot work.
 

1 more replies
Answer Match 47.04%

I will try to keep this as brief as possible and yet give you wise and wonderful tech persons all the information you need to help me out. I am intelligent, but NOT a super-user.

I have an e-machines desktop computer. It is old. A Cyrix MII 266 processor with upgraded memory. I have a 10gb Maxtor hard drive which is the issue at hand. I am running Win2000. My home computer (the e-machine desktop) is networked through a router with my printer and my business laptop.

The problem: Win2000 loads and boots. It LOOKS like it's functioning properly. However, it cannot read any of the files on the disk. When I try, it tells me C: is inaccessible. I can't search, explore, etc. The files are "non-existent."

I managed to get Windows to create a backup of it and saved that file to my Laptop. I can only "assume" that it actually backed up ALL the files on the drive so they are safe.

One really ODD thing you should know is that I cannot get into the BIOS. When it boots and usually gives you that second or two to hit [F2] and enter setup ... doesn't do that any more. I sit and hold the F2 key. Nope. I've second-guessed myself and tried the ESC key and the F1 key. I've tried it with and without the CTRL key. Nothing. So I can't even tell the silly thing to boot from the CD instead, load onto my D: backup drive and then kill the C: drive. It's like it's possessed.

Things I've already tried (not necessarily in this order):
1... Read more

A:Solved: Hard Disk issue similar to "Help! Broken Hard disk" Thread

14 more replies