Tech Problem Aggregator

# Boot Configuration Data Error

Q: Boot Configuration Data Error

I recently booted up my Gateway notebook only to find the "blue screen of death"

I rebooted and it came up to a windows boot manager screen which says windows failed to start..insert installation disc and click repair to fix...blah blah...i'm sure you know the story...

My question is, I booted the Vista disc and when I click repair it doesn't even find the C: drive...when I try and run the BCD fix from the command prompt screen, it says it found 0 Windows installations...would this indicate a faulty hard drive?? If so, I dont mind replacing the drive, I just wanna make sure this is the issue before I spend the money to replace it...

Much thanks for any help anyone can offer!

A: Boot Configuration Data Error

I'm not sure what BCD fix you tried, but see if it is this one and if not, try this one.

To run the Bootrec.exe tool, you must start Windows RE. To do this, follow these steps: (you need a Vista Installation Disk to do this)

1. Put the Windows Vista installation disc in the disc drive, and then start the computer.
2. Press a key when you are prompted.
3. Select a language, a time, a currency, a keyboard or an input method, and then click Next.
5. Click the operating system that you want to repair, and then click Next.
6. In the System Recovery Options dialog box, click Command Prompt.
7. Type Bootrec.exe, and then press ENTER.

Note If rebuilding the BCD does not resolve the startup issue, you can export and delete the BCD, and then run this option again. By doing this, you make sure that the BCD is completely rebuilt. To do this, type the following commands at the Windows RE command prompt:
 bcdedit /export C:\BCD_Backup
 c:
 cd boot
 attrib bcd -s -h -r
 ren c:\boot\bcd bcd.old
bootrec /RebuildBcd

See if that works.

If you don't have the disk (or that didn't work), try EasyBCD http://neosmart.net/dl.php?id=1 and see if that helps resolve the problem.

If that doesn't work, you probably have some type of hardware problem - but it's hard to tell. It may be as simple as the hard drive cable got disconnected and all you have to do is reconnect it and everything will be fine. While it may be the hard drive, it could also be other hardware components. If you have another PC in which you can slave this hard drive, do that and see if you can access the contents (not boot to it but just read what is there). If so, it possibly isn't the hard drive that's the problem. It would help to get a complete and exact word-for-word description of everything on the BSOD as that may help identify the true source of the problem - post it here so we can research it and see if it tells us anything useful (it may help or it may be too general to help - but we won't know until we see it).

If you do decide to replace the hard drive, then be sure you can return it and get your money back in case the new hard drive experiences the same problem when you try to install or when you try to run after installation if installation works. That would mean the problem most likely isn't the hard drive and there's no sense spending money on devices you don't need so you can return the one you purchased. I would try the following first, however, to possibly resolve the problem and save you the hassle of getting another drive.

See if it now works. If so, you're back in business. If not, at that point try the hard drive replacment if there is no financial risk. If that doesn't work, I would recommend a reputable computer repair shop for service, diagnosis, repair, and possibly replacment of defective components.

Good luck and I hope this helps!

3 more replies

Computer: Dell Inspiron 1525, 320 GB HD with about 2 GB of free space left, 4 MB memory, running Vista Home Premium 32-Bit, SP1, updates current. Just lately, booting from off, Windows will not load, but instead gives me a \Boot\BCD error (0xc00000f)--an error occurred while attempting to read the boot configuration data. I have repaired this error with my Dell-supplied OS disc repeatedly, and each time I turn off the computer it has the same error at startup. I have read that I may have to rebuild the BCD, but I don't know how to do that. Before I check with Dell, who I suspect will just tell me to reload Windows, I need to know how approach fixing my boot configuration data. The computer has had no new software installations, just routine Windows and Trend Micro Internet Security updates, I checked the disc for errors, and a few files were missing or incorrect, and defragmentation has also been performed routinely. Dell PC checkup finds no issues. How should I proceed?

A:Boot\BCD error reading boot configuration data when starting from cold boot

Try this hard drive diagnostic procedure: http://usasma.vox.com/library/post/b...agnostics.html

Repeated errors on a hard drive usually indicate an impending failure. I'd backup your stuff as soon as possible.

5 more replies

Several times, and only from a cold boot, I get a pop-up stating "Boot Configuration Editor Has Stopped Working" However everything loads okay and functions. What might be causing this and what does it mean. IE: What function does this editor serve?

SYSTEM SPECS

INTEL I7-920 PROCESSOR
WINDOWS 7 HOME PREMIUM 64 BIT
12 GB TRI CHANNEL DDR3 SDRAM AT 1333 MHZ
1 TB 7200 SATA 3.9 GBS 16 MB CACHE
CREATIVE SOUNDBLASTER X-FI
DELL WIRELESS KEYBOARD AND MOUS

Dave K.

A:Boot configuration data editor error win 7

Run Startup Repair on a cold boot.

5 more replies

Have a HP compaq 6300 pro running windows 7 pro. today computer would not boot,

black screen came up it asks me to insert installation disc

scrolling down it lists the following

file \boot\BCD

Status: 0xc000000f

info: an error occurred while attempting to read the boot configuration data.

unfortunately since windows came preinstalled there was no installation disc

it said since it was preinstalled to contact manufacturer.

my support/ waranty with HP for this computer has ended

Thanks in advance for any assistance in this matter

Bob J

If you have access to another Windows 7 computer create a System Repair Disk. Boot it and do a Startup Repair. It may take up to three attempts to fully do the repair. If you have 64bit then you would need to find a Windows 7 64bit computer.

2 more replies

Does anyone no how to fix this? Yesterday I got a UAC Zero Access Virus and tried using windows repair disc to go back to a restore point. That just made everything worse and now I can't boot into windows at all. I have a multiboot PC (its set to just windows 8 and windows 7 right now, windows 7 being the biggest partition on the drive).

Recovery
Your PC needs to be repaired

The boot configuration data for your pc is missing or contains errors.

File:\Boot\BCD
Error code: 0xc000000f

A:The Boot Configuration Data For Your PC Is Missing or Contains Error

Can you boot into either of the two operating systems?

15 more replies

Hi, I was running Windows 7 on a Dell Vostro 3700 Laptop..After doing a spyware scan and finding and deleting all the entries I found, the next time I turned it on I get the error: oxc000000f "An error occured while attmepting to read the boot configuration data File: \Boot\BCD"

I have looked online for solutions and tried using the Windows 7 disc (a copy) and also tried using 3 recovery disks, these all fail because it just stays completely black with a cursor (left for hours even) or I get a error message something around the lines of "insert correct boot media into the correct boot device" and I have no idea what this means. I cannot do a repair because I can only get the Windows disc to load if I remove the hard drive?? this is the only way I have got it past the green loading bar, so I am stuck and have no idea what to do..it only seems to respond to cds if the hard drive is removed?.. this all happened very suddenly and now I have a very expensive ?800 paperweight.. Any help massively appreciated!

To add to this - I also tried the command prompt typing the bootrec.exe code that I found on the internet..selecting command prompt from the option when the Windows 7 disc was loaded, but basically it came up with an error of some sort and it had a drive letter of X:/ on the command prompt ?? ..Also to get to this the hard drive was removed because like I said I cannot get the discs working with it in.. I'm guessing this means the hard drive is screw... Read more

A:Error oxc000000f Need help repairing Boot Configuration Data??

Are selecting the optical drive as your boot device for the windows install disk? sounds like maybe with the hard drive removed its defaulting to the optical drive and booting correctly. Also, make sure you have a good copy of the windows disk.

8 more replies

I have a Dell and won't boot giving a black screen but will boot after about 10 turn on and offs. It is very annoying and have uploaded the latest drivers for the system. Since installing Windows 7 there seems to be this erratic problem with the Dell XP. Anyone have an idea about how to fix this problem?

A:[MOVED]Re: Boot configuration data editor error win 7

Moved from this topic: http://www.techsupportforum.com/f217...ml#post2898619

1 more replies

My Dell Insperion 15 now has this boot error. I tried using the recovery USB from my HP. It is smart enough to know that I'm not trying to reboot the HP computer so it doesn't work. This is so frustrating. What to do?

A:windows 8.1 error 0xc00000d boot configuration data

Check HDD with this: Hard Drive Diagnostics Tools and Utilities (Storage) - TACKtech Corp.
Test your RAM: RAM - Test with Memtest86+ - Windows 7 Help Forums
one stick at a time eight passes per stick
Drive letters in WinPe will probably be different from what you see in windows - that is normal.

I would delete the bcd store and run the commands again. You should be pointing them at the reserved system partition .

Otherwise, at cmd prompt, type:

diskpart

lis vol

( Look to see the drive letter for your main windows partition - if it is D then type as below, otherwise replace D with the letter diskpart gives for the main windows partition)

sel vol d

act

exi

bcdboot d:\windows /s d:

bootsect /nt60 all /mbr

restart the pc - you're good.

7 more replies

Help I can't get past the booting error and there is no way for me to pass this? I've tried many things and can't get past it

File: \Boot\BCD
Status: 0xc000000f
Info: An error occurred while attempting to read the boot configuration data.

OS: Vista x64 Bit

A:Error while attempting to read boot configuration data?

1 more replies

Hi, thank you. glad to be the newest member here. I have an Aspire S3 laptop Windpows 8 to 8.1 - that now has a BCD error blue screen upon start up that is error OXCOOOO0D - boot configuration data Recovery

Your PC needs to be repaired.
The BCD is missing some required info.
File:\BCD
you'll need to use recovery tools...

I don't have an install/repair cd/dvd, and I don't have my product key - since its on the BIOS and is unretrievable. I want to save ALL my files so, please, if someone can help, thak you! All I tried so far is to get into the BOOT by pressing F2 and switched it from UEFI to Legacy only it asks for BOOT disk...

A:windows 8.1 error 0xc00000d boot configuration data

Bump.........

9 more replies

This is the error message that my computer had:
"Recovery
Your PC/Device needs to be repaired
The Boot Configuration Data for your PC is missing or contains errors
File:\EFI\Microsoft\Boot\BCD
Error code: 0xc0000185
You'll need to use recovery tools. If you dont have any installation media (like a disc or USB device), contact your PC administrator or PC/Device manufacturer.
Press Esc for UEFI Firmware Settings"
I made a recovery drive and set the UEFI to a USB boot, and when I tried to boot it with a blank USB it didnt recognize it, but when I used the recovery usb it recognized it. I did that to check and see if it actually recognized the recovery data.
Now when I boot it just has the Lenovo screen and the swirling dots. it's been doing this for about a half hour. Is this normal or is there an issued with the hatdware?

A:Boot Configuration Data is missing, Error Code 0xc0000185

The Error code: 0xc0000185 is an I/O error.
This can be a hardware problem or a software problem.
So the first thing to do is to run diagnostics on the hard drive ( http://www.carrona.org/hddiag.html )

If you have difficulties booting to the disk/drive, post back and we'll see about changing some settings in the UEFI to allow the boot.
I'm working on a drive that will do this for you, but it's still in the testing phase (and it's a 700+ mB download).

If the drive is dead/dying, you may have problems trying to recover your data.
Do you have a recent backup?  If not, post back for suggestions on how to best backup your information.

FYI - if it is dying, then it's best not to use the drive at all until you've done the backup.
If the drive does die fully, then data recovery gets very expensive (up to $2000 (US)) if it's even possible. 0 more replies Answer Match 76.02% Hi everyone, I have windows 8.1 and Lenovo y510. After upgrading from 8.0 to 8.1 a have several problems with my PC. Right now suddenly i cant start my PC. I have BSOD Recovery Your PC needs to be repaired. The boot configuration data file is missing some required inforamtion. File\BSD Error Code:0x0000034 Need to use recovery tools on your instalation media. If you dont have any contact your system administrator or PC manufacturer. ESC for UEFI firmware setting. I try different setting in setting utilty (after pressing ESC) and nothing changed. I dont have any USB or Disc with windows. (but i do have legal copy - it was already installed in my PC) so i cant use any of help with restoring pc from instalation media. Do you have any idea what to do ? Thank you very much. A need it pretty serious that pc because of school A:Error 0x0000034 - Boot Configuration Data File is Missing From the Repair CD/USB: How to do a Auto Repair: Automatic Repair - Run in Windows 8 Note: You may need to do startup repair 3 to 4 times. Startup Repair - Run 3 Separate Times - Windows 7 Help Forums Have you made the OEM manufacturer's Recovery Disks? Information We always assume you have made your Recovery Disks using the OEM manufacturer's Recovery Media Creator app the first day you had your new PC. & made the Startup Repair CD. (Windows 8 only) Recovery Drive - Create with USB Flash Drive in Windows 8 System Repair Disc - Create in Windows 8 (Windows 8 only) I would recommend you making the OEM manufacturer's Recovery DVD's or USB drive. or You can order the Microsoft official OEM Recovery disks from the OEM manufacturer's website. From the manual for Lenovo G480. Originally Posted by Lenovo When the hard disk drive or solid state drive is replaced because of a failure, no product recovery program is on the new drive. In this case, you must use the Recovery Disc Set for the computer. Order the Recovery Disc Set and the drive at the same time so that you can recover the new drive with the pre-installed software when they arrive. You can Order Lenovo Recovery Disks from here: Lenovo Support - Home (US) Click on Parts & Accessories. 2 more replies Answer Match 76.02% Hi, I was running Windows 7 on a Dell Vostro 3700 Laptop..After doing a spyware scan and finding and deleting all the entries I found, the next time I turned it on I get the error: oxc000000f "An error occured while attmepting to read the boot configuration data File: \Boot\BCD" I have looked online for solutions and tried using the Windows 7 disc (a copy) and also tried using 3 recovery disks, these all fail because it just stays completely black with a cursor (left for hours even) or I get a error message something around the lines of "insert correct boot media into the correct boot device" and I have no idea what this means. I cannot do a repair because I can only get the Windows disc to load if I remove the hard drive?? this is the only way I have got it past the green loading bar, so I am stuck and have no idea what to do..it only seems to respond to cds if the hard drive is removed?.. this all happened very suddenly and now I have a very expensive ?800 paperweight.. Any help massively appreciated! To add to this - I also tried the command prompt typing the bootrec.exe code that I found on the internet..selecting command prompt from the option when the Windows 7 disc was loaded, but basically it came up with an error of some sort and it had a drive letter of X:/ on the command prompt ?? ..Also to get to this the hard drive was removed because like I said I cannot get the discs working with it in.. I'm guessing this means the ha... Read more A:An error occured while attempting to read the boot configuration data! Go to your BIOS and set the CD as the first boot device, your hard drive as second. If this lets you boot from the Win7 CD with the HDD installed run Startup Repair - Run 3 Separate Times. 7 more replies Answer Match 76.02% ok i had some recent windows updates succesfuly and rebooted, since that at start up im getting "Error msg : Boot configuration data editor has stopped working" any way to sort this ? what cause it ? Have tryed system restore several diffirent restore dates but still the same. Using a Dell studio xps 8100 win7 home edition 64 bit . A:Error msg : Boot configuration data editor has stopped working Try running system file check . SFC /SCANNOW Command - System File Checker 4 more replies Answer Match 76.02% Hi all, im getting that message upon startup. Im running windows 7. It requests for the windows recovery CD to be inserted, so when I put the CD in to boot I get a "windows is loading files" then a starting windows with the windows logo then just a black screen with a cursor, I left it like this several times for at least an hour an nothing happened. I can't press F8 to access safe mode etc, nothing will happen. Pressing F12 to boot from CD just does the same thing as putting the CD in normally. Help please!? A:An error occurred while attempting to read the boot configuration data It seems the CD is damaged. Burn a new Windows 7 Recovery CD on another computer. You can download the image or make a copy of a functional Windows 7 Recovery CD. Boot the new Recovery CD and run automatic StartUp Repair up to three times as sugested in the forum manuals ! Good luck! 1 more replies Answer Match 76.02% Hi everyone, I tried to install new updates of Ableton live and the machine crashed badly... and since them it has really gone a bit wonky. When I press the on button to boot up the laptop I get the following message. The Windows Boot Configuration Data (BCD) Store file contains some invalid information. Object : GUID : (8cb2db4-7co5-11de842e-bt611d44fefa) Description: Windows recovery format. Status: oxcoooooo24 Info: The configuation for an element within the object is invalid in the boot configuation store. The assiocated windows boot loader entry may not be available for selection until the problem is rectified by an administrator. Enter= continue. So then I press enter... it boots up. (in about 5 seconds as it is a ssd...) When I do this action: to see if I can do a restore etc... Start-Control Panel- the progress bar at the top of the expoler window freezes half way and I cannot access any of the menu Items. Also I canot move this panel or close the window. I have a back up on another external drive ..... plus I have made a repair disk and so on when I first got the machine. I would be stoked if you could provide me with the next steps so I can resolve this situation. Thanks for your time, now lets party on and delve deep into the abyss A:Windows Boot Configuration Data (BCD) store file error. Hallo, hatte auch einen 0x0000024 BCD Fehler. Hatte vor einer Installation die alte Partition auf "VERSTECKT / HIDDEN" gesetzt und nach der Installation vergessen die Partition wieder auf "Partition anzeigen / Show partition" zu setzen und erhielt so bei Bootversuch einige Tage sp?ter den x24 Fehler. Nach dem "ANZEIGEN" funktionierte der Boot wieder. 2 more replies Answer Match 76.02% Hi This is the full error message I encountered--> An error occurred while attempting to read the boot configuration data File: \Boot\BCD 1) I have an old Dell Vostro 410, Windows Vista, configured to RAID 1 the whole time. 2) I wasn't able to boot it up one day, pressing the on button only got an amber light momentarily. From the symptom, I replaced the CMOS battery as suggested by someone online and the PC was able to be powered up but it got to a blue screen--> https://www.dropbox.com/s/nyeoq0gwz4i3f2b/2013-12-21%2000.44.17.jpg 3) I realized that's because all the settings on BIOS has been wiped out after I took out the old battery, the "SATA mode" in BIOS was set to IDE instead of RAID, so I set it back to RAID as shown--> https://www.dropbox.com/s/u6oxdg8m092v0vr/2013-12-23%2000.01.31.jpg 4) I tried rebooting the the system again, this time I can see that RAID has been setup accordingly--> https://www.dropbox.com/s/a708qln2oehrm75/2013-12-23%2000.03.57.jpg and https://www.dropbox.com/s/1sfrpfrxtkgke2n/2013-12-22%2023.58.37.jpg 5) But the rebooting was terminated with the message "an error occurred while attempting to read the boot configuration data" --> https://www.dropbox.com/s/orgkn29qaj0nxsb/2013-12-22%2017.48.20.jpg 6) Following the on screen instruction, I tried booting from "Windows installation" CD to repair it, however after pressing a key on the following screen,... Read more A:An error occurred while attempting to read the boot configuration data When you removed the CMOS battery it set the BIOS to the default settings. I suspect you will have to rebuild your RAID configuration. 3 more replies Answer Match 76.02% system configuration data updated ERROR,--Need a solution I have a fairly new Gateway M-1625 laptop running windows vista 32 bit, sp1. I turned it on and beeped twice (beep, beep) and gave me an error message that reads "system configuration data updated ERROR, system configuration data read error" Press f1 to continue f2 to enter set up. I pressed f1 and it sent me to another blank page that reads. Windows failed to start. A resent hardware or software change might be the cause. To fix the problem: 1. Insert your windows installation disc and restart computer 2. Choose your language settings and click next, 3. Click ?repair your computer.? If you do not have the disk, contact your system admin. Etc Tried the repair disc, tried reinstall from Restore DVD still get the same message. Tried the bootrec.exe/fixmbr (worked) Tried the bootrec.exe/fifixboot (Worked) Tried the bootrec.exe/Rebuildbcd Tried reseating the memory and hard drive. Still at the same point. Even tried to install XP over it but never could get it to go. Now I am back to where I started. I already replace the hard drive so i know is no that I think this is a boot problem. what can I do??? More replies Answer Match 75.18% Hi All, I have read most of the messages related to this. Unfortunately ASUS doesn't ship with a Vista disk and the Recovery DVD doesn't boot. Details shown are File: \Boot\BCD Status: 0xc000000f Info: "an error occurred while attempting to read the boot configuration data" Operating medium - Windows Vista Any suggestions, Pls? I may have to return to Techs who MAY have a Vista disk. Cheers A:an error occurred while attempting to read the boot configuration data (Vista) Hi Wawny, Thank you for the post. The error message usually indicates that the boot sector is damaged or missing. We can try to use the following methods to troubleshoot the issue. However, performing the following steps requires a Windows Vista installation disk. If you do not have a disk, please contact your computer manufacturer or Microsoft Customer Service or to obtain one. Microsoft Customer Service: (800) 426-9400, available Monday through Friday, from 6:30 A.M. to 5:30 P.M. Pacific Time. Note: Microsoft Customer Service mainly handles issues regarding replacement manuals, disks, drivers and service packs, product IDs, lost CD keys, product orders, policies related to copying software on additional computers, licensing, and product registration. Method 1: Startup Repair from the Windows Recovery Environment (WinRE) ============================================ 1. Insert the Windows Vista installation disc into the disc drive, and then start the computer. 2. Press a key when the message indicating "Press any key to boot from CD or DVD ?". appears. 3. Select a language, a time and currency, and a keyboard or input method, and then click Next. 4. Click Repair your computer. 5. In the System Recovery Options dialog box, choose the drive of your Windows installation and click Next. 6. At the System Recovery Options Dialog Box, click on Repair your computer. 7. Click the operating system that you want to repai... Read more 15 more replies Answer Match 74.34% Hi, I have exactly the same issue as the person on this page, however I have already tried the three solutions and neither work, further explanation below. http://social.technet.microsoft.com.../thread/022386ba-a445-44ba-97f7-d8ba4b6cc54b/ I was watching a DVD on my PC last night when it began to stutter and finally the system completely froze. I would like it 5 min and then the PC would work again for roughly 5 sec before crashing again, I let this go on for about 20mins but the PC never fixed itself so I rebooted. On rebooting I got the above message. 1. My first attempt to fix it was using safemode, this however didn't work and it prompted me to use the repair progam on the Vista installation disk . 2. I booted from the vista disk and tried a start-up repair. This ran, said something was fixed and asked me to reboot. I did this but to no avail therefore I went back to the repair centre. 3. I did not have system restore turned on so this option was not useful to me. 4. I then read something suggesting I use Bootrec. However I tried running bootrec /RebuildBcd but it could not find my OS, instead I used the following commands; * bcdedit /export C:\BCD_Backup * c: * cd boot * attrib bcd -s -h -r * ren c:\boot\bcd bcd.old * bootrec /RebuildBcd This however didn't work either. 5. I left the PC overnight and now things seem to be worse. When I try and use repair centre it does not actually detect a HDD with Vista installed, it does however still let me p... Read more A:Answer an error occurred while attempting to read the boot configuration data (Vista) If you can take the HD out and put it into another PC as Slave and see if your data is still readable. 1 more replies Answer Match 73.5% We are getting the above error randomly on some of the laptops we have deployed. The error comes right after you boot or when the windows 7 is left running. There are no special software running. The error in details is below. "The boot configuration Data (BCD) settings for the following boot application have changed since Bitlocker was enabled boot appplication: \windows\system32\winload.exe change settings: 0x26000090 You must supply a bitlocker recovery key to start this system. Confirm that the changes to the BCD settings are trusted. If the changes are trusted then suspend and resume bitlocker. This will reset bitlocker to use the new BCD settings. Otherwise restore the original BCD settings" Can anyone please explain on how to correct this error. As before this is happening on few of the machines and we are seeing more as we go. Any tips would be nice...Thanks More replies Answer Match 65.94% I am running Windows 7 64 bit Ultimate on two PCs on my home network. I went to use one yesterday and was presented with a black screen. I rebooted the PC hoping that would solve my issue and was presented with the following error message while trying to reboot: Windows failed to start. A recent hardware or software change might be the cause. File: \BOOT\BCD Status: 0xc000000d Info: An error occurred while attempting to read the boot configuration data I checked my other PC and saw that it had been updated with several Windows patches yesterday. I'm guessing that the broken PC had an issue installing or rebooting from one of the patches. I ran the repair utility on the windows 7 dvd as instructed by the error message. It was unable to find a previous installation of windows with an error box saying: The file or directory C:\Boot\BCD is corrupt and unreadable please run Chkdsk utility. I tried the auto repair anyway, which appears to be working until the end when it gives me the "The file or directory C:\Boot\BCD is corrupt and unreadable please run Chkdsk utility" error again. Then it says it can't save the fixes and says it can't be repaired. When I check the details it says I need to "repair offline" and that it cannot find an OS installed. In my searches for an answer, I read about rebuilding the BCD through the command prompt. I ran the following commands: BOOTREC /FIXMBR - said it was successful BOOTREC /FIXBOOT - said it was succes... Read more A:\BOOT\BCD 0xc000000d unreadable boot configuration data Check your ram. Memory Diagnostics Tool Memtest86+ - Advanced Memory Diagnostic Tool Check with a hard drive diagnostic tools. http://www.tacktech.com/display.cfm?ttid=287 9 more replies Answer Match 65.52% Hello everybody, I wouldlike to know how to enable/disable the BCD. Can you help me please? T.Y. in advance antivirus is warning about the BCD is allawing non-signed drivers installation. Would like to fix this. Is it worth it? A:Boot configuration data (BCD) Being worth it or not, really depends on what you want it for, can you give any more info? 9 more replies Answer Match 65.52% I was on my PC, my dual boot failed, windows boot configuration data is now gone. I don't have a system install disk, don't have an order number the manufacturer needs to send me one, nothing I've tried worked. The status error is 0xc0000098. Is there a way to fix it without the install disk? Some sort of repair tool I can download? If I could even get a command prompt open I could fix it but it won't boot at all. A:Boot configuration data gone Downloading Repair ISO which is small size file is illegal as per Microsoft. But you can download the ISO for Windows 8.1 Enterprise Evaluation, burn it to a blank DVD and then use it to repair your system. The file size is more than 3 GB. http://technet.microsoft.com/en-us/windows/hh771457.aspx OR Just ask one of your friends for their Windows 8 DVD and repair your system in a few minutes. This is why you should create a repair disk the first time you boot your Windows computer. 6 more replies Answer Match 64.68% so DEP doesn't like my skype and thus won't let it stay open. i had DEP turned off before, but then i had my computer wiped and all this and that, so i had to turn it off again. but the tutorial on here by brink for how to turn it off isn't working this time, and i get a message that says "boot configuration data store could not be opened. access denied." what can i do to fix this? A:boot configuration data could not be opened? my boot configuration data apparently cant be accessed, so this isnt working, and for the life of me i cant find a way to get access to it. i tried looking at the comments a few times and dep closed chrome each time i tried. HELP. 1 more replies Answer Match 64.68% Hi, When I start my computer this is the screen it gives me: I do not have a dvd/cd drive on my laptop and the codes that are on the bottom of the laptop are not readeble anymore. What can I do?? Thanks! A:Boot configuration data is missing 1. Welcome to Tech Support Guy 2. What is the make and full model of the laptop please 3. What OS was on the laptop originally- was that Windows 8/8.1 or what please 4. Do you have a usb flash pen drive and if so what capacity is it please 1 more replies Answer Match 64.68% When I try to boot my Lenovo Flex 3-1580, Windows 10-64bit, I get the following BSOD: "The Boot Configuration Data for your PC is missing or contains errors. File: \EFI\Microsoft\Boot\BCD Error code: 0xc0000034" I haven't been able to get it to try booting from a USB, but I did try reinstalling Windows. That failed when it told me to restart and it went back this issue. When I tried to find solutions online, they all assumed the computer could boot, so were useless. Any help is appreciated! Thank you! More replies Answer Match 64.68% So I just downloaded adware delete or w.e to remove vosteran search which had bee plaguing me for a while. I delete the files it tells me to and as I restart the computer I get the "Recovery$ system files are missing error code 0xc0000034 File :\BCD. Now I've done the research and it seems I only have 3 options. Windows 8 DVD, windows 8 drive or booting it to system recovery. I don't have the flash drive OR the windows 8 disc and pressing F11 at boot up doesn't do squat... I'm really terrified. I think my computer is done for? If for some reason I manage to fix
d, the bcd, will that detele all my data? System specs: Lenovo ideapad core i5 windows 8 model name 20191. Any ideas suggestions?

A:Boot configuration data is missing

Windows 8, "Missing File: \BCD Error Code: 0xc0000034"

1 more replies

I was attempting to install xp as a dual os system. After setting up my partician vista still would not let me install xp , older version error. I used a program vista bootpro or bootpro and changed my boot configuration trying to get it to allow me to install xp. Now I cant boot up my laptop. Only system info I have is toshiba, 2 years old lots of ram, How can I change my BCD back so that I can boot up vista. I tried from xp cd, safe mode, last known. I don't have the vista disk with me at the moment, Can I get it to boot up with that disk? If not how can I create a emergency boot up disk for vista?

Dean

A:Boot Configuration Data Changed

Hi,

I think you might have to wait until you get the Vista disk back.

That will just repair the boot configuration without any problem.

There are various boot disks HERE and the Ultimate Boot CD

but I`m not sure they would be much use.

There is a very good page HERE for dual booting XP/Vista

3 more replies

When I try to boot my Lenovo Flex 3-1580, Windows 10-64bit, I get the following BSOD: "The Boot Configuration Data for your PC is missing or contains errors.
File: \EFI\Microsoft\Boot\BCD Error code: 0xc0000034"
I haven't been able to get it to try booting from a USB, but I did try reinstalling Windows. That failed when it told me to restart and it went back this issue.
When I tried to find solutions online, they all assumed the computer could boot, so were useless.
Any help is appreciated! Thank you!

A:Boot Configuration Data got corrupted

Hi toasterbot,

It's not an uncommon issue mate, and not that hard to fix. You will need to boot from your Windows disk to fix it .

Boot your computer using Windows installation media
Select the correct time and Keyboard type.
Click Repair your computer in the lower left corner.
Select Troubleshoot from Choose an option screen.
Click Advanced options in Troubleshoot screen.
Click on command Prompt.
Type these following commands one at a time and hit enter after each line of command:

Bootrec /fixmbr
Bootrec /fixboot
Bootrec /scanos
Bootrec /rebuildbcd
shutdown -s

After about a minute after the last command your machine will shutdown. You can remove the Windows media now.

TsVk!

1 more replies

So I have been literally trying to fix my windows not being able to boot at all for more than 12 hours straight till now. I almost read every single article and troubleshooting step on the web to find a solution but nothing seems to work. I will keep it short as much as I can.

I was playing the Division game on my PC then suddenly the PC crashed and then it restarted by itself but stuck at the windows logo forever. I tried system restore using the windows recovery CD then it failed as well, since then, whenever I try to boot from my HDD, it gives the error 0xc00000f "The Boot configuration data for your pc is missing or contains errors"

I then boot through the CD in the cd drive, have only 4 or 5 options which are

1 - Reset this PC
2 - Refresh this PC
3 - System Restore
4- Command Prompt
5- Automatic Repair

the "Reset this PC" gave an error "The required drive partition is missing"
the "Refresh this PC" gave an error "The drive where windows is installed is locked. Please unlock and try again"
the system restore gave an error something I don't actually remember but its like "Choose your OS and then try again"

I tried the so-called commands in the CMD (bootrec /fixboot, /fixmbr, /rebuildbcd, etc...) and all didn't work. Also the rebuildbcd command showed that "Total identified windows installations is ZERO"

Tried the diskpart command as well and when I listed all the volumes, all appeared as Healthy a... Read more

More replies

the boot configuration data store could not be opened, access is denied

A:boot configuration data store could not be opened

Hi Kevin Hill I guess you're trying to use BCDEdit from the command prompt? You need to right-click on the Windows logo and select Command Prompt (Administrator) otherwise it won't work as you need Admin Rights to use that utility.

25 more replies

I need to recover boot configuration on my acer computer

More replies

Hi my  name  is sandy,     i just  got the  HP 15 F233  Notebook about 10  months   ago.  and i had done the  useual  factory   install   because it seemed  like it was going  slow    i never    had a  problem  with it before  until  a couple day's ago   it ran smooth no hicups  nor  errors. after   that i would  normally shut down the laptop and hope to resume my work  on the  computer the following  morning  when i  finally did turn  on my laptop  on,   this what i saw on my   screen  i have done  the factory install countless   of times  on my other    computers that i had in the past    and  I've never had this happened   my main concern  when    i  get the recovery  tools disk  would  it restore    the factory  install settings  you know  HP  Should   included  CDS and  other materials with their  laptops and desktops  as needed  ty

A:The boot configuration data for your Pc is missing or contai...

Hi, Turn off your computer then turn it back on and immediately tap away ESC button then select F11 then select "Troubleshoot" and then "Advanced" and try these steps:b.Select "Advanced options" and then select "Command Prompt".c.If prompted, enter in the password for the user name.d.At the Command Prompt, type the following commands and hit enter.?bootrec /scanosbootrec /fixMBRbootrec /Fixbootbootrec /rebuildBCD?If prompted to press yes then press Y then restart if not then type the code below??chkdsk c: /f /r /x After running the commands your computer should restart and will automatically install windows update. Sometimes it will take for a while to update. Just extend your patience and wait until your computer restarted successfully. DONT LEAVE YOUR COMPUTER UNATTENDED.. Hope it helps.

"Education costs money; so does Ignorance"If my post has helped you, click the Kudos Thumbs up!If it solved your issue, Click the "Accept as Solution" button so others can benefit from the question you asked!

1 more replies

Hello. Last night I set Acronis Disk Director to merge two partitions on my C drive.
I had an unnallocated 100mb that used to be partitioned as system reserved, but I deleted that partition as it was not needed. So I made a new partition out of that unallocated space and set it to merge with my primary partition on my c drive. It restarted my computer and 40% through, showed an error and restarted quickly. Now I get the following message when attempting to boot my computer:

File: \Boot\BCD
Status: 0xc0000225
Info: The Boot Configuration Data for your PC is missing or contains errors.

The second partition, that I attempted to merge, now has 1mb of space on it. Whenever I try to run chkdsk on the primary partition, it says that the disk structure is corrupt and uunreadable.

Any help would be greatly appreciated. I need my c drive recovered.

A:The boot configuration data for your pc is missing/errors

The system reserved has The Boot Configuration Data for your PC.

Try this:
From the Repair CD/USB:
How to do a Auto Repair:
Automatic Repair - Run in Windows 8
Note: You may need to do startup repair 3 to 4 times.
Startup Repair - Run 3 Separate Times - Windows 7 Help Forums

17 more replies

Hi I'm trying to fix my nephew's laptop.  It is a Toshiba P75-A7100 running an Intel Core I7 processor. It came with Windows 8.1 installed and he upgraded to Windows 10 when it was available.  other than these recent developments the laptop has been running fine.

Right now I'm getting a Windows failed to start message.

File: \EFI\Microsoft\Boot\BCD
Status: 0xc000000f
Info: The Boot Configuration Data for your PC is missing or contains errors.

History:

He was receiving Unexpected Store Exception errors, the first time while updating a steam game, then while working on a photoshop project.  He ran system file checker (sfc.exe) and the output file has 23,977 lines most of which say Primative installers committed for repair.  (i have a copy of this file if needed)

I removed his hard drive and attached to my laptop with a USB to IDE/SATA cable adapter and ran a AVG ( my anti virus) scan on it and it came back clean. I was going to copy his documents, music and other user files to my laptop but under C:\Users his account is missing.  All that's there is Default, Default.migrated, Public, and TEMP (which looks weird to me, I dont have a TEMP user on either one of my PCs)

I reinstalled his harddrive into his laptop, downloaded a Windows 10 ISO from Microsoft's website burned it to a dvd, went into his bios and changed it to boot from dvd first. I tried to run Startup Repair. It went through diagnosing yur PC and Attem... Read more

More replies

My brother brought his PC to me with the above error.
The rest of it is File: \BCD and error code 0xc0000034. And of course being my brother he did not make a recovery CD. There is also no windows twenty five digit serial number sticker on the case. So can someone direct me where to proceed from here? Thank you for any guidance....

A:Boot configuration data file missing

Startup repair (up to 3x consecutive runs might be needed, but probably only 1) will fix it.

You might try your luck with "finding" a Win 8 (or 8.1 if you have that instead) .iso to burn or make a USB out of, so you get to startup repair. Check hashes if you do this, compared to known well discs or official disc.

Someone will probably have a suggestion or two how to get one. Maybe even officially.

It would be helpful to everyone if you give the exact machine model and submodel (if there is one).

9 more replies

Hi folks, couple weeks ago I bought a new server to my company, and installed Server 2012 Foundation to it. Also, using Intelligent Provisioning, I enabled RAID 10 (4x1TB HDD). When OS was installed, I changed DVD-drives letter from D to E, and then in disk management I created new volume, D (labeled Data). Through Windows Update service I think almost every available update was installed. The server is a database server in a basic WORKGROUP (not part of a domain), which sends and receives information from our retail stores and online store, it acts as a central database for all the operations. It doesnt run for example our online store by itself, it is "just" a computer which keeps all the data in - it doesnt do any "urgent" matters for example run a site. Locally, in a LAN network it also provides access to our erp sofware. So = it is just a basic computer, which just needs to work, no matter else. This server is going to replace our really old ML310, which is still doing its task. Today I booted our new server, but as you can see in attachment, it didn't boot. I can't understand what happened. It says BCD file is missing... No changes has been made in a week. Last time I just shutted the server down. I tried to use "bootrec" commands in recovery environment's command prompt screen, but it didnt help (commands I found from another forums, I dont know do they only work in consumer pc's). Also, using automatic repair with installation DVD didnt help ... Read more

More replies

Blue scree

More replies

My Dell Inspiron 13 running on Win 8.1 has a blue screen crash on startup with the message along the lines of Boot Configuration Data missing etc. I learn from this https://www.dell.com/support/Article/us/en/19/SLN287103/EN post that I need to basically recover from a separate boot cd or drive, but i procrastinated on making one while my laptop was still OK. Then I hit a snag with trying to make one via downloading according to instruction here http://www.dell.com/support/article/us/en/19/SLN130027 because apparently my warranty had expired and because of that It wouldn’t allow me to download and make a USB Key… (Really, Dell, why? Why not just give consumers a boot cd/usb key in the first place?)

What can I do?

A:Inspiron 13 Out of Warranty, Boot Configuration Data crash

Hi REYLEE,
The OEM media is available for purchase while placing the order.
Ensure the HDD is fine before you troubleshoot the OS - Restart the system and press f12 key on startup - choose diagnostics. Let it run the diags and if you encounter any errors - make a note of the complete error and report the same to us.
You would basically need the OEM media to repair the OS as stated in the first article you have posted.
If you are in the US / UK - you could order the media online - http://dell.to/12vcZ27
Let us know if you have any other queries.

1 more replies

I hope that someone can help me I had restarted my computer which is HP Pavilion Elite m9150f, and I got this message on my screen as the computer started to boot up. It says "Recovery The boot configuration data file is missing some required information. File:\Boot\BCD error code: 0xc000000d You'll need to use recovery tools. If you don't have any installation media like a disk or a USB Drive, check your PC administrator or PC/device manufacture." I do not have a recovery disk is it possible to get one from hP customer support? Anyones help on this matter will be greatly appreciated.

A:Recovery The boot configuration data file is missing

Assuming either Vista or Windows 7, then THIS THREAD has the typical answer.  Of course you need a real install disk for Vista or Windows 7 or a repair disk.  You can borrow an install disk from someone and boot to the disk and pick repair instead of install.  As long as you do not try the install it will be fine.  Read the link. HP does not provide a disk, so that is your choice to find one.  Like I said, you can borrow one.

4 more replies

Yesterday, my laptop fell off the end of my desk.  No visible damage to the laptoop, but I can not boot.  I get the error that configuraiton data missing or contains errors.  it says that one of my options is to insert a  Windows installation disc and restart the computer.  I do not have a disc.  Is there anything I can do to try to get my computer up and running.  I am past the warranty period, and I don't have any idea how much it would cost to send in to be fixed.

More replies

I restarted my laptop today and then I get a blue screen with the following message
Your PC needs to be repaired
The boot configuration data file is missing some required information
file :\BCD
error code: 0xc0000034

you'll need to use the recovery tools on your installation media. if you don't have any installation media (like a disc or usb device), contact your system administrator or pc manufacturer.

press esc for uefi firmware settings
when i bought my laptop, windows 8 was already installed and i did not get any installation disc

how do i fix this problem?

A:boot configuration data file missing required information

Look over this procedure and see if you feel comfortable in using it.

How To Fix The Windows Bootloader ? TweakHound

I know you don't have a Win 8 disc at this point but I am more concerned with your level of comfort in executing the above.

1 more replies

Not sure if this is the correct forum, please forgive me if I've posted it in the wrong forum.

Hi folks I?m a newbie to the forum and would really require some assistance, I?ve owned PC?s for a considerable time and I am pretty flummoxed with a problem I?ve encountered. I haven?t a clue how this occurred and for the life of me cannot seem to recover my PC. I have used various approaches on your forum to hopefully correct this issue but to no avail.

When booting from disk I get the message the file
File: \Boot\BCD Status 0XC0000098
Info: The windows boot configuration data file does not contain a valid OS Entry

I used the helpful guide ?How to Fix Windows When it fails to Boot? on this form and ran the following: Initially running system repair

The computer scans itself during this phase and looks for windows installations it returns the message no windows installations found. When I view the Diagnose and repair details I get the following:

No OS files found on disk
Repair Action: Partition table repair
Result: Failed error code 0X490

I have ran the repair process 3 times and booted between each repair

I progress beyond this and run the following:

Bootrec.exe /Fixmbr runs successfully
Bootrec.exe /Fixboot runs successfully
Bootrec.exe /RebuildBCD runs and returns successfully scanned windows installations
total identified windows installations: 0 completed successfully

My Laptop is a 4 year old ACER 8390G running Windows 7, it has a Hitachi 500Gb hard drive and the p... Read more

A:Windows boot configuration data file does not contain a valid OS entry

Hi jdoherty, Welcome to forums.

Check out this link. FIX boot error.

Hope this helps.

9 more replies

Hi,

When launching my Microsoft Surface 3 with Windows 10, I get a blue screen as below;

Recovery

Your PC/Device needs to be repaired

The Boot Configuration Data file doesn't contain valid information for an operating system.

File: \BCD
Error code: 0x0000098

You'll need to use recovery tools. If you don't have any installation media (like a disc or USB device), contact your PC administrator or PC/Device manufacturer.

If I hold the volume down key on boot up, I can get into some sort of setting screen where I have set the below settings;

Trusted Platform Module (TPM)                                                          [Enabled]

Secure Boot Control                                                                             [Disabled]

Device Information

Configure Alternate System Boot Order                 [Network -> USB -> SSD]

Exit Setup

I downloaded MediaCreationTool.exe file from Microsoft's website and installed it on a USB. With that... Read more

A:The Boot Configuration Data file doesn't contain valid information...

Hi to BleepingComputer

Access the Command Prompt like you did before and try the following:

- Type Bootrec /RebuildBcd, and then press ENTER.
If the Bootrec.exe tool runs successfully, it presents you with an installation path of a Windows directory.
To add the entry to the BCD store, type Yes. A confirmation message appears that indicates the entry was added successfully.
If the Bootrec.exe tool cannot locate any missing Windows installations, you must remove the BCD store, and then you must re-create it.
To do this, type the following commands in bold in the order which they are presented:
- Bcdedit /export C:\BCD_Backup
- ren c:\boot\bcd bcd.old
- Bootrec /rebuildbcd

0 more replies

Hi, had a few problems dual booting and managed to get every thing fine. Installed easyBCD and clicked install to the wrong partitionNow when i boot after the bios it appears "windows failed to start, a recent hardware change might be the problem." Offers solutions to boot from CD which i have but wont boot. Will just appear the same screen.file:\boot\bcdinfo the windows boot configuration data file does not contain a valid OSDell inspiron 1720

A:info the windows boot configuration data file does not contain a valid OS

Resolved. Managed to get cd to boot.

1 more replies

Hello, I apologize if this is in the wrong forum, and if there have been threads about this issue before, but I've searched for a while and could not find a solution that I could understand from reading, as I am a newbie. Whenever I start up my computer, it shows this:
Windows failed to start. A recent hardware or software change might be the cause. To fix the problem:
2.) Choose your languange settings, and then click "Next."
If you do not have this disc, contact your system administrator or computer manufacturer for assistance.
File: \Boot\BCD
Status: 0xc0000098
Info: The Windows Boot Configuration Data file does not contain a valid OS entry.
The computer runs windows 7 and is an Acer Iconia Tab W500, so it's a hybrid tablet and laptop and did not come with an installation disc, nor does it have a disc drive due to its size. I can't access the window that pops up with F8, the only screen that can appear is the F2 screen.
I'm fine with completely restoring the computer to factory settings, or pretty much anything that will get the device working again. The problem is, I can't figure out how to either repair the file or restore. I'm really sorry if this is really confusing or if I didn't provide enough information, I don't have any experience with computers, but any advice on how to fix it?

A:Windows Boot Configuration Data File does not contain a valid OS entry

Do you have a Windows 7 Repair Disk?
Do you have, or can you borrow, a Windows 7 installation DVD (Same version as yours)?

If you follow the instructions in that message using either disk the chances are good that you can repair the problem.

If you can't get your hands on a DVD, then when turn your computer on - tap on the F8 Key as soon as it comes on. When the black screen with options appear, select "Repair your computer." When you see the option, perform a Startup Repair.

If startup repair fails then select the last option which allows you to access a command prompt. You might want to enter these commands at the prompt:

bootrec.exe /fixboot
bootrec.exe /fixmbr
bootrec.exe /rebuildbcd

3 more replies

windows boot configuration data file does not contain a valid OS entry (0xc0000098)

Trying to fix my aunts laptop (Toshiba satellite/windows 7). Tried a recovery disc, which was painfully slow but no joy.
Here is screenshot of boot:
http://oi46.tinypic.com/2ut3kmb.jpg

Partition check with 'partition wizard':
http://oi46.tinypic.com/2z6tv92.jpg

I was able to explore the "system reserved" partition, which shows boot folder etc:
http://oi50.tinypic.com/34fdw79.jpg

When I explored the larger partition it only showed "(Disk 1 Partition 2)
http://oi45.tinypic.com/11iif5g.jpg

I did the diskpart thing in command prompt:
vol 0= E dvd rom
vol 1= C 100mb partition (active)
vol 2= D 232gb partition

Any advice on what to do to try fix this missing OS.
Thank you.

A:windows boot configuration data file does not contain a valid OS entry

If you ran Factory Recovery it apparently failed. Had you asked first we could have helped you work through the steps for Troubleshooting Windows 7 Failure to Boot. Now there is likely nothing to repair, although you can try Startup Repair after marking Win7 or its boot partition Active.

What I would do now is get and maintain a superior Clean Reinstall - Factory OEM Windows 7 . Everything needed is in the blue link.

If it fails to install, reset BIOS to defaults: Clear CMOS - 3 Ways to Clear the CMOS - Reset BIOS

While in BIOS setup set SATA controller to AHCI to try install. If that fails try IDE mode.

If install still fails try wiping the HD from the installer's Command Line using Diskpart Clean Command

Report back results as there will be more steps if necessary.

3 more replies

I keep getting this error message at start up. It gives me the option of F1 to resume or F2 to enter set up. When I hit F1 it starts fine enough but I'm concerned about this. Follows is a start up list report and then a hijack this log.

start up list log

StartupList report, 4/15/2006, 8:49:48 PM
StartupList version: 1.52
Started from : C:\Program Files\StartUpList\StartupList.EXE
Detected: Windows XP SP2 (WinNT 5.01.2600)
Detected: Internet Explorer v6.00 SP2 (6.00.2900.2180)
* Using default options
==================================================

Running processes:

C:\WINDOWS\System32\smss.exe
C:\WINDOWS\system32\winlogon.exe
C:\WINDOWS\system32\services.exe
C:\WINDOWS\system32\lsass.exe
C:\WINDOWS\system32\svchost.exe
C:\WINDOWS\System32\svchost.exe
C:\WINDOWS\system32\spoolsv.exe
C:\WINDOWS\Explorer.EXE
C:\WINDOWS\GWHotKey.exe
C:\Program Files\HP\HP Software Update\HPWuSchd2.exe
C:\PROGRA~1\Grisoft\AVGFRE~1\avgcc.exe
C:\Program Files\Logitech\MouseWare\system\em_exec.exe
C:\Program Files\Zone Labs\ZoneAlarm\zlclient.exe
C:\WINDOWS\system32\ctfmon.exe
C:\PROGRA~1\Grisoft\AVGFRE~1\avgamsvr.exe
C:\PROGRA~1\Grisoft\AVGFRE~1\avgupsvc.exe
C:\PROGRA~1\Symantec\NORTON~1\GHOSTS~2.EXE
C:\Program Files\Common Files\Microsoft Shared\VS7DEBUG\MDM.EXE
C:\WINDOWS\system32\nvsvc32.exe
C:\WINDOWS\System32\svchost.exe
C:\WINDOWS\system32\ZoneLabs\vsmon.exe
C:\WINDOWS\system32\utilman.exe

More replies

Hello,
I have no idea where to start, a friend of mine sent me a link for Windows 8 Pro link, it's not original nor cracked, it's just non-activated (it kept asking me for activation key), that's not the problem tho.
I have windows 7 already, downloaded the iso he sent me, I tried to extract it into a flash, tried to boot from it, it didn't work, I said why not extracting it? I did, and opened setup.exe, and installed windows 8 successfully! And I could dual-boot normally.
I went back on windows 7, backed up my files into another partition, renamed the partitions into Windows 7, Windows 8, Others(backup) and went to windows 8 and started restorting from the new parition, after all I went to delete windows 7 in a stupid way by deleting the Windows 7 partition, it didn't work fully, some folders stayed as Windows/Windows.old ....etc, so I went to windows 8 partition to extend it since I deleted lot of gbs off the windows 7 partition, I've done so, and there was option saying to make it primary parition althought it was checked on windows 7, I checked on it and it went unchecked on windows 7, I didn't care much.. and it asked for reboot, and I did.

And here's the problem, it cannot boot anymore ...
It gives this error:
"The Boot configuration Data for your PC is missing or contains errors."

I certainly don't have any idea where this problem was made, because there's like 3 mistakes ..

1- Resizing and moving location of partitions?
2- Trying to del... Read more

More replies

Hi, my friends alienware laptop has encountered the BSOD. The error reads.
File: \BCD
Error code: 0xc0000034.
I understand this problem can occur from someone not switching off their computer or laptop properly and thus not allowing the boot configuration files to be written properly. I have had this problem before with my own computer but I managed to fix the problem using command prompt. I cant remember the specifics on what commands I used although I remember using things such as, chkdsk and dskpart.
I'll start of with chkdsk, after typing chkdsk and hitting enter I get the following message. "The type of the file system is NTFS. The volume is in use by another process". Then chkdsk verifies files (stage 1 of 3) and everything is fine, then verifies indexes (stage 2 of 3) same again, everything is fine and then lastly verifies security descriptors (stage 3 of 3) which then comes with the following message. "Errors detected in the uppercase file". I then try chkdsk /f which comes with the following message. "The type of the file system is NTFS. Cannot lock current drive. Windows cannot run disk checking on this volume because it is write protected.
Now for the dskpart problem. typing dskpart works fine, then when typing commands such as, "list disk" and "list volume" comes with the following message. " There are no fixed disks to show" and "There are no volumes" I am at a complete loss at this as in my si... Read more

A:Alienware m17x Windows 8.1 BSOD (Boot configuration data missing)

Try doing a factory restore... Or a fresh install of Windows. Sounds like the laptops hard drive has failed

1 more replies

Help !!

I had to clean up my system, reapplying SP2. I tried to reinstall Nero 7 using same installation package that worked previously. I get this error:

"the configuration data for this product is corrupt, contact support personnel"

I installed Windows Installer 3.1 and still have this problem. I cleaned out all references to Nero in the registry... no luck.

A:Error 1610 ? Configuration data for this product is corrupt (Nero install)

Start button, Run, regedit

Navigate to:

HKEY_LOCAL_MACHINE\SOFTWARE\CLASSES\INSTALLER

You need to look under the key Features. By examing each of the keys found here you will eventually find one that very clearly states it is for Nero and state the version.

Nero will have two entries. One under Features, and one under Products. For example, my Nero 7 UltraEdition used these two keys to store its configuration information:

HKEY_LOCAL_MACHINE\SOFTWARE\Classes\Installer\Features\62E2F0A3CB0C8B04495AA6AF7BBA0133

HKEY_LOCAL_MACHINE\SOFTWARE\Classes\Installer\Products\62E2F0A3CB0C8B04495AA6AF7BBA0133

Your results are likely different only in the long number string portion at the end.

Delete the key under Features and under Products by right-cliking and choosing delete.

Reboot. Try the installation again.

1 more replies

0x000000
0xFFFFFFE6
0x000001F
0x000000
0x80F7650B
OR SOMETHING ALONG THOSE LINES

More replies

Hi,
somehow my win7 system boot records seems corrupted hence it's showing OS not found. i have tried with bcdedit /enum & its showing "The boot configuration data store could not be found. The requested system device cannot be found". tried
bootrec /fixmbr & bootrec /fixboot which is showing sucessfully. bootrec /rebuildbcd is able to detect C:\windows but showing "the requested system device cannot be found" while adding installation to boot list. i went into diskpart, selected
EFI partition & able to see EFI contents (bootx64.efi/bootmgr.efi etc) there.
Kindly suggest how can i recreate BCDstore without reinstallation.
Regards,
Dhiraj

A:BCDEdit /enum showing "The boot configuration data store could not be opened"

When you boot the machine make sure you are booting with a UEFI device i.e. if you boot with a Win7 CD, make sure that the CD is booting from UEFI and not legacy BIOS CD. You have to boot from the same type of partition that the hard drive was created with
for BCDEdit to work.

So if you booted from WDS network, then you need to boot from a UEFI ethernet/pxe connection.

4 more replies

This is the message I get when I try to boot:

"The boot configuration data for your PC is missing or contains errors"

File: \EFI\Microsoft\Boot\BCD
Error code: 0xc000000f

I had a linux partition installed separate from my windows partition. I deleted the linux partition, which apparently messed up the windows boot loader since it seems to have been overwritten by the linux boot loader. i tried installing linux again to restore its bootloader, but selecting windows from the boot loader is no use since the windows boot loader no longer works. i've been using the command prompt in the windows 8 recovery environment but have not had success so far.

A:"Boot configuration data is missing or contains errors"

Delete Linux, boot off of the Windows 8 DVD choose your language and Repair Your Computer. That should fix the boot file.

3 more replies

A:System Configuration Error and no Boot up :(

Hi and welcome. See if you can start in safe mode. For a system this old, I doubt you'll get anywhere calling the number in the computer manual anyway.

1 more replies

I recently tried to turn on my pc and the boot manager screen is up and no matter what i do for several days now i cant get past this screen someone please help ive tried everything

A:Boot Configuration Error 0xc000000d

See Troubleshooting Windows 7 Failure to Boot

3 more replies

Windows Boot Manager
An error ocurred while attempting to read the boot configuration date.

The instructions are to insert the Windows disk and restart the PC, however I can't get past this screen. When I restart I end up on the same screen.

How can I get past this error screen?

Thanks.

A:Boot Configuration Error Screen

Try following these steps. an error occurred while attempting to read the boot configuration data (Vista)

5 more replies

So today I went to use my computer when all of a sudden I got a message giving me the 3f0 error. I ran a diagnostics test and it said it could not detect the hard drive. I decided to open the pc ( p7-1234) and make all the wires were plugged in (which they were) then tried again. It didn't work so I did some research.I found a bunch of post on forums about people saying open up you secure boot configuration menu and enable legacy bios. The only problem is I don't have that option under the security tab or anywhere to be honest. Can any one tell me what to do now?

More replies

On boot up the laptop beeps twice and the message "system configuration data read error" appears with F1 to resume or F2 to setup. If I hit F! it boots up as normal. When I switch off and reboot the same ting happens every time...help its driving me crazy !!

More replies

I moved and expanded a partition on my computer (moved left) and have gotten this error upon boot.

"An error occured while attempting to read the boot configuration data."

I have tried using the startup repair tool and using the repair console to run BootRec.exe /RebuildBcd, to no success.

I cannot undo the changes as the partition's were join and now form one complete hard disk. Can anyone help me?

A:Error reading boot configuration file after partition moving

7 more replies

Windows 7 x64 system installed last week. All has gone well until a while ago...Adobe Acrobat downloaded an update and installed it, then asked to restart the machine.

At restart Windows quit and offered to restart normally or to repair itself. I let it try to repair itself, but it repeatedly failed, with the error:

*Boot configuration is corrupt.
Result: Failed. Error code=0x490*

In addition, I noticed that windows apparently is not finding the boot drive...looking at the repair log I saw:

System Disk=\Device\Harddisk\Windows directory-\\?\GLOBAL ROOT\Device\Harddisk1\Partition2\Windows

Windows appears to be looking at the wrong disk...it's installed on a new drive with only one partition. Using the Command Prompt option in the repair window, I could not access the *real* drive "C" (Drive 0), only Drive 1, which has two partitions for D and E.

Hiren's Boot CD running NTFS4DOS does not see drive 0 at all and also shows Drive 1, Partition 1 as drive C. Hiren's mini-WinXP shows a drive C designated as "System Reserved" - and shows Drive 1 as drives D and E on its partitions 1 and 2 respectively.

Mini-WinXP shows the otherwise elusive disk 0 as disk F.

I could sure use some ideas for a fix...I didn't have many to begin with and by now I'm down to none! Thanks in advance, if anyone can help.

More replies

My  HP Envy sleekbook 4-1200eo came with windows 8.0 and was uppdated to 8.1 and later with windows 10 preview. All has been working ok until a month ago. Have been trying to boot again and managed to get as far as the final of installing windows 10. After that it says bcd error 0x0000034, need to contact supplier etc...Now I can only start and se the content of f1 and f2 keys ( ie computer installations and repectively diagnosticss test) but not enter the f9,f10 and f11 which contains the menues for rebooting. I cannot install w10 with a download from microsoft page, the computer just won´t recognize the memory stick. Nothing happens.Pls someone, help me out

More replies

My  HP Envy sleekbook 4-1200eo came with windows 8.0 and was uppdated to 8.1 and later with windows 10 preview. All has been working ok until a month ago. Have been trying to boot again and managed to get as far as the final of installing windows 10. After that it says bcd error 0x0000034, need to contact supplier etc...Now I can only start and se the content of f1 and f2 keys ( ie computer installations and repectively diagnosticss test) but not enter the f9,f10 and f11 which contains the menues for rebooting. I cannot install w10 with a download from microsoft page, the computer just won´t recognize the memory stick. Nothing happens.Pls someone, help me out

More replies

I have a persistent problem on my old computer, which has prompted me to buy another computer, but I still want to fix my old computer.

My computer will occasionally fail to boot up properly. The symptoms that I see when this happens are as follows:
-Text on bootup has some random letter replacements (ex. "I hate my computer", would show up as "I hgte mh cvhmuter").
-The Windows boot screen image is corrupted with what appears to be static.
-Windows will not boot up successfully under these conditions, and the computer will hang.

What I have done to resolve this:
-Put the old graphics card back in with no change (this started maybe a week after I installed a new graphics card)
-New Motherboard (actually, the old one blew up shortly after this problem started happening - smoke and everything, so I was just hoping this would kill two birds with one stone)
-Fresh install of Windows on a new hard drive (This had to do with cleaning up drivers related to the old motherboard, without erasing the old hard drive, and I had a spare hard drive kicking around)
-Removing and swapping RAM (I noticed it would happen less often if I had less RAM, but I was not able to isolate any bad RAM chips, and they all passed a memory check)

What is still the same in the computer since this started happening:
-CPU
-RAM sticks
-Power Supply and Case

(I cannibalized everything else for my new computer, and threw all my old CD-drives and peripherals back into this computer to try a... Read more

More replies

Hi guys,

I was working on a computer that needed a new power supply (that's another story), but anyway, I went ahead and replaced it and everything is fine. I reset the bios and now Windows 7 will not boot. I tried using a windows 7 home premium disk to boot up (f8 repair option is gone) and run some bootrec commands which found 2 installations (windows.old and windows) both of which I have added.

If I try to boot from the 'old' installation, it boots up but never logs in.

If I try to boot from the CORRECT installation, it says "windows failed to load because the nls data is missing, or corrupt".

I tried going into the bios and changed IDE to AHCI and vice versa, thinking maybe setting the bios to default settings threw it off, but i get the same issue. Any ideas?

A:NLS Data is missing boot error

Boot off of the Windows 7 disc and choose Repair Your Computer. If that fails, In the RE (Recovery Environment) you can choose System Restore. You also can choose Command Prompt
First determine what Drive the OS has been assigned by the RE

At command prompt (x: sources) type:-
bcdedit | find ?osdevice? (Must inc?) (press enter).

Now use the returned as the drive letter for OS assume C:

At the x sources type:- chkdsk c:/r (press enter), 5 stages of chkdsk will run.
can take awhile.

To run sfc/scannow
at the x: sources type:-
sfc/scannow /offbootdir=c:\ /offwindir=c:\windows (press enter)
sfc will run can take awhile
Last resort you can browse the windows.old and search for *.*nls files and copy them and paste them into C:\Windows\System32.

4 more replies

Hello folks,

I hope you can help. My problem is extremely similar to those described here:

http://www.tomshardware.co.uk/forum/239448-35-nightmare-kernel-data-inpage-error

Problem

In short, I first noticed chkdsk running automatically and rewriting the indexes for various files on my filesystem. I'd previously tried to download part of the guest client for Starcraft II, but cancelled it part way through. I assumed that somehow this had left partial files scattered around my filesystem and chkdsk was just cleaning up.

After this, I started to get the system hanging whilst using memory-intensive programs (possibly also associated with our router losing the internet connection). BSOD then came up after about a minute with a kernel data inpage error, stop code 0x7a.

Occasionally after rebooting it hangs on "detecting IDE drives" after doing POST and checking the memory.

It also reordered the boot order of my hard drives, preventing the system from booting properly without a bootable DVD in the disc drive. This problem has been fixed as I just changed the boot order back in the BIOS.

Specs

Sorry some of these are a bit vague, the PC is running a bootable virus scan at the moment and I'd rather not interrupt it or go digging in the case.

Intel Q6600 processor @ 2.33GHz (not overclocked, stock cooler, temps are fine)
4GB Corsair Dominator @ 800MHz (default timings, 5-5-5-12, I think)
ASUS P5 model (can't remember exactly the model)
150GB WD Raptor ... Read more

More replies

Hello, I've been using my computer (Vista ultimate 64bit) for awhile without problems until a few days ago. I noticed the harddrive was running hard and there were 3 processes that usually arn't running (WMI Provider Host). So I figured it was doing an update or something important so I let it run, a few minutes later we had a blackout and my surge protector didn't work. Booted back up to find it saying the following:

File: \Boot\BCD
Status: 0xc000000F
Info: An error occured while attempting to read the boot configuration data.
It also says to use the install disk to use repair but it doesn't work. And on top of that the repair menu says "Operating system: Unknown on unknown local disk."
Is there any way to fix it without having to reinstalling windows?

P.S.- I'm pretty sure it also said something about a corrupt system registry but it's not showing that anymore.

A:Error attempting to read boot config Data

Update: I've read other threads about this and nothing they have done seem to work. I've tried running the following commands in the console and they don't work:
BOOTREC /FIXMBR
BOOTREC /FIXBOOT
BOOTREC /REBUILDBCD
And they all are succesful except on rebuildBCD and it says the OS cannot be found even though in the list it shows C:/Windows as the first and only OS.

1 more replies

Hi everyone,

I encounter the following when trying to create the ISO image for the window server 2012 r2.
my system itself is running 2012 r2 as well.
what is this error referring? how do i  resolve it.

More replies

Today when I restarted my computer, the boot screen indicated that the Windows file 32 was missing or corrupt.

I used my recovery CD to "repair" the issue, and the warning indicated that no data would be erased. Well, that is partially true - folders on my C: drive are intact, as are all programs but...MS Office and my User settings (bookmarks, etc. but most importantly my Outlook pst file which contains 6 years of data!). It appears the User folder with my name is gone.

I knew something was wrong when the PC booted after the repair, and asked me to customize settings as if the PC were brand-new.

Any advice is most appreciated on how to recover my settings and e-mail data in Outlook and Outlook Express. I am running WinXP Media Center edition. Thank you.

A:Windows XP Boot/Recovery Error - Data Missing

Hello KCN77

What do you mean by a "Recovery" CD? Was is a proper XP installation CD?

Try looking in C:\Documents and Settings. Check out everything there.

Try searching for
****.pst and see if anything is found

.

9 more replies

I have a toshiba laptop running windows xp. It crashed yesterday and now whenever it boots it give me the following error:
Press ctl alt del to restart.

I managed to get to the selection of boot in safe mode, but it still won't boot and then I get I/O error reading boot sector.

At this point I just want to get the data off it. Toshiba's recovery disk only has the option of formatting the disk and restoring the system to it's initial state (the Toshiba tech support explained that was a benefit, getting it back to the original state, I told him scrapping my data on a 6 month old machine is not something I would consider a benefit)

So, tell me different ways I might get that data off the disk before wiping it clean? I have other computers and an external hard drive at my disposal.

A:Boot Sector Read error - help recover data

Slave the drive out on another machine?

2 more replies

First, apologies if this is the wrong forum for this; Backup & Recovery seems like Maintenance, so I put it here.

I have been using the built in Windows 7 backup feature for several months without any problem. My last successful backup was on March 6th. The last attempted backup on March 13th (set on weekly schedule) failed for the following reason: "The volume for a file has been externally altered so that the opened file is no longer valid." The details show an error code of 0x800703EE. Every attempt to manually back up fails within a minute for this reason.

My backups all go to a big external hard drive connected by USB. I haven't had any problems like this in the past. Searching on Google reveals very little concrete info about what this means or how to fix it, although quite a few people seem to have come across it. The most informative post on the subject was this, which has the following solution:

Quote:
Issue is resolved. The root cause was error in bcd, bcdedit was giving "The volume for a file has been externally altered so that the opened file is no longer valid" when trying to /enumerate active. Fixed it manually by building new BCD and doing a import followed by reboot. I guess windows backup internally tries to enumerate BCD and fails without correct log/message when enumeration is not successful.
Backup is running fine now.

I think BCD refers to "Boot Configuration Data," which worries me. T... Read more

A:Error backing up data; dual boot related?

So... is this basically a mystery?

3 more replies

I think I may have made a big mistake, I inadvertently manually deleted ACDSee Pro2 and now I keep getting a Windows Installer dialog box that reads: “The configuration data for this product is corrupt. Contact your support personnel” I believe I may have deleted something I should not have. I’ve downloaded Windows Installer 3.1 and that did not help. I can load(install) other programs with no problems, but I can’t reinstall ACDSee Pro2 .I’ve downloaded from different sites and still the same results.
Anybody have any Ideas I can try. Thanks

A:Configuration Data Is Corrupt

hm maybe something in the registry is causing you greif? unfortunatly i dont know much in the feild of registry cleaners, someone else may be able to lend a suggestion or 6 :D otherwise just misc. search for acdse in there?

goodluck

15 more replies

hey, my mom got a blue screen of death today and asked if i could help fix it. it turns out she was getting a kernel_data_inpage_error, so i decided to try and fix it, then i logged in safe mode and got a new BSOD and then tried again and got a unmountable boot volume. so im trying to use Recovery Console and it wants a administer password which of course she forgot. i tried "offline nt password & registry editor" but got error code 13.. so now i cant get ride of the adminster password nor can i get ride of the unmountable boot volume errorthis is what im following for the boot volume error:http://www.tech-recipes.com/rx/2605/fixing...t_volume_error/so any help getting ride of the password, or fixing the boot volume error would be most excellent!and i cant reformat it just yet because she needs to backup her tests and quizzes she has made - shes a teacherits a old dell peice of crap laptop with Windows XP Home SP3

A:kernel data inpage error / Umountable Boot Volume

You can attempt to fix the unmountable boot volume error...by running chkdsk /r...with the drive from your mother's system attached to another system as an additional, non-boot drive.Wait...that's wrong . It's right but it's the wrong answer for you.The administrator password asked for in the Recovery Console...probably doesn't exist. I don't know of any home user who has ever set one, so try just hitting Enter when you get to that.How to use CHKDSK in the XP Recovery Console - http://pirules3.14.googlepages.com/recovery_console_chkdsk If it moves to the command prompt, you win.If not, go back to my first sentence.Louis

6 more replies

Hello

My dell latitude 640 xp office has blue screen error unmountable boot volume ( recently prior has been sluggish, had to force shut down over and over, fan seemed louder, about 3 wks ago installed verizon dsl,) right before I turned it on and got this message I had turned laptop over to look at fan info to check into ordering new one.
ok so get the BLUE SCREEN STOP: 0x000000Ed error, tried doing the F8 , nothing, on last known config, or start normal, tried sage mode gives me quick list of multi disk /partition /windows2/ system2/ 32drivers......... too quick to get all info then back to unmountable boot volume screen.

so somehow upon starting got into a symptom tree and ran test under system lock up and windows blue screen test cam e up with

motherboard fan on/off error code 3700011B 3700:011B Msg expected fan on high rpm of 8000 detected fan RPM0 under both system lock up and window blue screen test

also under IDE DISK Read Test Device Blue screen test received 2 errors saying Error Code 0F00:0244 Msg Block 8368093:uncorrectable data error or media is write protected

... and IDE Disk Verify test error code 0F00:aA44 msg block 8368093 uncorrectable data error or ,media is write protected.

any suggestions on what to do next or what real problem is, need to retrieve current work info I am on a deadline. Thank you

A:Unmountable Boot Volume/fan Erro/uncorrectable Data Error ...

Looks like a dead hard drive to me - the unmountable boot volume along with the IDE errors tend to support this. Means a new hard drive and a fresh install of Windows. I don't know about your data - you'd have to slave the drive to another system to see if anything is recoverable.

I'm unsure about the fan error - and would suspect that there's an overheating issue inside your case also. I'd recommend cleaning out the case with a can of compressed air - particularly the area with the loud fan. Don't use a vacuum cleaner or a garage air supply as it may damage your system.

1 more replies

Four days ago I decided I needed to backup my computer so I downloaded easeus todo backup free and let it work. While it was backing up I did some general spring cleaning, ran disk cleanup, got rid of old downloads. Then randomly my computer crashed, restarted up to a blue screen saying:

Your PC/Device needs to be repaired
The Boot Configuration Data for your PC is missing or contains errors.
file:\Boot\BCD
Error code: 0xc000014c

I can no longer boot into windows.

I didn't create a recovery tool but I used my bootcamped macbook and windows media creation tool to put a windows 10 installer on a usb. I've been trying to use the repair options within the installer but nothing has worked so far:

- Start up repair doesn't work, get the message "startup repair couldn't repair your PC"

- I've also tried a couple of things in command prompt, sfc /scannow, but it hasn't worked either, maybe I'm not doing it right I'm not sure.

I'm not sure what else I can do, some help would really be appreciated!

Also, I'm running windows 10, upgraded from windows 7, on a custom built computer.

More replies

I'm trying to connect a C# program to an Access database, but the wizard keeps crashing every time... Here's as far as I can get...

Wizard opens up
Click "New Connection"
Click "Change"
Select "Microsoft Access Database File" from combo box.
Click "OK"
Type "PROVIDER=Microsoft.Jet.OLEDB.4.0;DATA SOURCE="C:\\Data\\TimeSheet.mdb;" into the ConnectionString text box (tried leaving it blank as well).
Click "Test Connection"
Receive "Test connection succeeded." message box
Click OK
Click OK to continue wizard

This is where I receive the error message, which is

"Format of the initialization string does not conform to specification starting at index 0."

If I set up the connection, data adapter, and dataset in the program itself, I don't have any problem, just if I try to use the wizard. Also tried to set it up in VB .NET, but have the exact same problem. Thanks in advance.

Try specifying just the folder name and not the filename, you can specify the file later in the code.

2 more replies

Hi,

I would first like to thank usasma for helping me a year ago with my laptop, I forgot to reply and mark my thread as solved. I haven't had a BSOD until now.

My laptop has been acting up the last couple of weeks. I had a windows update a couple of weeks ago and then I hadn't restarted it to update the changes. While surfing the web on google chrome I got a BSOD so my computer restarted and then started apply the changes. After that my computer took forever to boot up, the programs were very slow to boot up, it got to the point where my computer would freeze and then I would have to do a hard power off.

I initially got one BSOD error message "Cnbj2530.dpb and prbcacla.inf" and now I've been getting mostly "Kernel data inpage error" messages. My programs take a long time to boot up still, especially Google Chrome (Firefox seems to be a bit smoother). It also tends to get BSOD when I wake it up from sleep mode. I've attached the DM log. Thanks!

MCS-Mon_03_23_2015_195838_72.zip

A:BSOD, programs slow to boot, Kernel data inpage error

Update or uninstall drivers in red. Please follow these instructions: GUIDE: CNBJ2530.DPB and prncacla.inf Corruptions - Windows 8/8.1 - Sysnative Forums

Code:
semav6thermal64ro.sys Wed Dec 28 21:17:03 2011 (4EFB793F)
Sony SEMA Thermal Input driver[br](part of VAIO Care)
http://www.carrona.org/drivers/driver.php?id=semav6thermal64ro.sys

GEARAspiWDM.sys Thu May 3 21:56:17 2012 (4FA2E2E1)
CD-ROM Class Filter Driver by Gear Software.[br]Also comes with iTunes
http://www.carrona.org/drivers/driver.php?id=GEARAspiWDM.sys

SMARTVHidMiniVistaAmd64.sys Mon May 7 23:47:31 2012 (4FA842F3)

SMARTVHidMiniVistaAmd64.sys - this driver hasn't been added to the DRT as of this run. Please search Google/Bing for the driver if additional information is needed.

SMARTMouseFilterx64.sys Fri May 18 19:07:31 2012 (4FB681D3)

SMARTMouseFilterx64.sys - this driver hasn't been added to the DRT as of this run. Please search Google/Bing for the driver if additional information is needed.

sows.sys Mon Jun 11 03:36:13 2012 (4FD54B8D)
Sony Wireless State Device Driver
http://www.carrona.org/drivers/driver.php?id=sows.sys

SFEP.sys Mon Jun 18 10:11:46 2012 (4FDEE2C2)

SFEP.sys - this driver hasn't been added to the DRT as of this run. Please search Google/Bing for the driver if additional information is needed.

IntcDAud.sys Tue Jun 19 16:40:51 2012 (4FE08F73)
Intel Graphics Media Accelerator HD Driver
http://www.carrona.org/drivers/driver.php?id=IntcDAud.sys

1 more replies

OK, so I just moved for the first time in years, and as soon as I get my PC set up in it's new home it goes all wiggy on me. I'm thinking the trip might have damaged something, but I don't really want to muck about any more than I need to, as the PC is my only good link to my girl right now and I need it to work asap. I also don't have access to my install disc, as it is back home at them moment which makes things interresting.

So, here are the symptoms.
It started with a strange behavior in windows itself, where windows would not minimize properly. I had to close one window to be able to view the one behind it. When I rebooted the machine, it failed to find the drive and tried to boot from CD. After a little finagling and removing the CMOS, it booted properly, but then promptly crashed. It freezes for a few minutes, and then eventually flashes a BSOD Kernel Data inpage error for a split second before rebooting. Sometimes it will also freeze for a minute or two then come back. Sometimes after a crash it boots right back up, other times it fails to boot. When it fails to boot, sometimes it tells me the boot manager was not located, other times it just says insert disk to boot from CD. Sometimes it will also hang in the middle of the boot cycle. When it hangs in the boot cycle, it will eventually boot after about 15 minutes. The lack of consistency in the behavior is really throwing me off.

The main hard-drive seems to be running hot, but I can't rea... Read more

A:Windows 7 BSOD, Boot failure, Kernel Data inpage error

Nobody has any ideas?

1 more replies

I just got a new Windows 8.1 PC and it works fine. As a recovery precaution I made a Windows 8.1 recovery disk on a brand new PNY USB 2.0 flash thumb drive (32GB drive) using the Windows 8.1 Control Panel Advanced Recovery tools "Create a Recovery drive" selection. I also indicated to copy the recovery partition from the PC when making this (but I don't delete this partition on the PC). So I thought I would test this recovery drive to see if I can boot from it. I insert the USB flash drive into a USB 2.0 port on the PC and restart the PC. I hit F12 during the PC boot process and select this disk as the temporary boot disk and hit return. The PC then gives me an error message screen basically saying
"Boot Manager
Windows failed to start. A recent hardware of software change might be the cause. To fix the problem:
1.Insert your Windows installation disc and restart the computer.
2.Choose your language settings, and then click "Next".
3.Click "Repair your computer." If you do not have this disc, contact your system administrator or computer manufacturer for assistance.

Status: 0xc000000f

Info: The Boot Configuration Data for your PC is missing or contains errors."

So I'm a little confused as to why the successfully just created recovery drive is giving me this error. I'll try another USB thumb drive to see if that makes a difference but I'm guessing it won't so thought I'd ask about this... Read more

A:Just created Windows 8.1 recovery disk (usb) gives Boot config data error

You are going to have to make the thumb drive bootable BEFORE you add any files to it... Try using these instructions:
http://windows.microsoft.com/en-us/windows-8/create-reset-refresh-media

1 more replies

When I start up my computer, I get a message at the log in screen that reads:
The Configuration data for this product is corrupt. Contact your support personnel. Then it won't allow me to do anything from there.
I don't know much about computers but I have tried to manually repair the boot configuration data but that didn't work. Could anyone please help me with this!! Thanks

A:Configuration Data Corrupt Message on Welcome Screen

Can you boot into Safe Mode?

What is the make and model of this computer?

2 more replies

Hi need help

I just opened my notebook and it has come up with the recovery screen with the above error.

Can anyone help me out

A:NB10t-A Error code 0xc0000034 Boot Config Data file missing

Are you able to perform a repair procedure?

https://aps2.toshiba-tro.de/kb0/TSB2A03ES0000R01.htm

To access the System Restore, Refresh and Reset options using the F12 option at startup, perform the following:

1. If not already, ensure the computer is completely shut down.
2. Now restart the computer by pressing the power button - IMMEDIATELY start tapping the F12 key on the keyboard until the "Boot Menu" screen appears.
3. Using the arrow keys, select <HDD Recovery> and press "Enter".
4. On the next screen you are asked to confirm if you want to contiue with recovery. Select "Yes".
5. The computer will bring you to the Advanced startup screen.
6. Select Troubleshoot. Under Troubleshoot you will see “Refresh” and “Reset”.
7. Select “Advanced options.” Located here is "System Restore."

1 more replies

The full message is
windows cannot verify the digital signature for this file
Might be something wrong with dual boot. My mom who knows nothing about this accidentally installed another Windows Vista so now i have 2 windows vista named: Microsoft windows vista and Windows Vista home premium
Everytime i boot Windows Vista home premium, i get that error.

Repair does not work. system restore, pressing F8, does not work.
Idk bout command prompt, i dont know how to use bcdedit.

I can boot Microsoft Windows Vista option fine, but it has nothing on it. I need to boot Windows Vista home premium option because all my stuff is there.

The problem with bcdedit is that i can only access it through the Vista CD, which brings me to the path X:. idk where to navigate from X:. and when i type in the command "cd C:" it brings me to : C: but i cant direct it to system32 to access bcdedit

The only way to access bcdedit it by booting Microsoft Windows Vista option, which again has nothing on it, but i dont want to change the Boot Loader osdevice option for THIS version, i need to change it to default C: for the Windows Vista Home premium one.

Help?

A:VISTA boot error 0xc00000428 Windows cannot verify the data signature of this file

BUMPp

5 more replies

When uninstalling store apps, will this also remove any data/configuration files associated with the app?

The reason I ask, I had a working Twitch app, Unstream. Lately this app only partially works, I can open streams from the notification but launching Unstream from the start menu opens a window and immediately closes it. I tried uninstalling the app but problem persists. I just want to make sure that I have completely uninstalled it before I chalk it up to a bug or some new incompatibly with my system. Trying to run it on a desktop PC, if that makes a difference.

Thanks.

More replies

Hi Guys (and Gals?)

SUMMARY:
I want to add a second wireless router to my existing home network. Also I plan to upgrade to a "smart" (internet-connected) TV within the next year so I'm trying to plan ahead. I have a decent-sized house with many THICK walls (no drywall here!). Tech-oriented family of 4.

Other details:

1. Existing router is Linksys E3000 and has served well.

2. Four endusers in house: all technophiles and heavy data users, often simultaneously.
-- Son connects his self-built gaming monster machine via Ethernet. Hard core gamer thus streaming is critical. Also art student but I'd say his build has accommodated those needs well.
-- Hubby laptop PC and tablet and phone; streaming to tablet is critical, esp. from upper floor bedroom.
-- Daughter phone and laptop; streams to both, often from upper floor bedroom.
-- Yours truly mom, (and network admin)... heavy reliance on self-built desktop (Win 8.1), Asus laptop (Win 7), tablet, smartphone (often all simultaneously), streaming, bluetooth(s) (plural?) , whatever else I come up with.

3. 3 TV's that use the cable modem, but I plan (hope!) to swap one of these in next year to a smart TV (love the Roku I use now, which of course connects to my wonderful e3000 router) The TV to swap is on main floor, front of house.

4. Wiring: I live in an old house; translate: brick exterior (awesome), very thick plaster walls interior (they don't make em like this anymore, sooo cool), small-ish ro... Read more

Are you concerned about 'ac' vs. 'n' because of file copies (or streaming) on your LAN? Or is your internet access faster than you can handle with 'n' Wi-Fi?

If you use a SOHO router as wireless access point following is the complete procedure.

JohnWill's procedure (Aug. 30, 2008) for configuring a secondary router as a switch and, optionally, wireless access point follows.

Connecting two (or more) SOHO broadband routers together.

Note: The "primary" router can be an actual router, a software gateway like Microsoft Internet Connection Sharing, or a server connection that has the capability to supply more than one IP address using DHCP server capability. No changes are made to the primary "router" configuration.

Configure the IP address of the secondary router(s) to be in the same subnet as the primary router, but out of the range of the DHCP server in the primary router. For instance DHCP server addresses 192.168.0.2 through 192.168.0.100, I'd assign the secondary router 192.168.0.254 as it's IP address, 192.168.0.253 for another router, etc.

Note: Do this first, as you will have to reboot the computer to connect to the router again for the remaining changes.

Disable the DHCP server in the secondary router.

Setup the wireless section just the way you would if it was the primary router, channels, encryption, etc.

Connect from the primary router's LAN port to one of the LAN ports on the secondary rou... Read more

3 more replies

Back for more and, as always, a hearty thanks to anyone willing to give of their time. For the last several months I've been running a dual boot configuration--XP Professional and Windows 7 Home Premium managed by GAG Boot Manager--on my HP Pavilion dv4 2040us with no problems. I mostly use Win 7, but roughly twice a week I'll boot into XP Pro to utilize a legacy app or just to update my anti-virus. Yesterday, 4 days since my last visit, I booted into XP Pro and was, for no reason that I can figure, confronted with the classic "We apologize for the inconvenience . . ." screen that asks if I want to start Windows normally or use the last known good configuration or start in Safe Mode or a few other options. Given that 4 days ago I booted into the XP partition with no problems I chose "Start Windows normally." However, after entering the splash screen, the dots moved across the bar below the logo for 3 complete cycles then, half-way through the forth cycle, the screen went black then reset to the Power-On password request (I have the "Power-On" password set to yes in the BIOS, so I receive this request every time I power-up). Also, it's exactly the same if I choose any of the other options, Safe Mode, last known good configuration, etc.: 3 cycles of dots then half-way through the forth cycle it resets to the Power-On password request. My last successful use of the XP partition went smoothly, and in the 4 days between visits to th... Read more

A:Suddenly Can't Boot XP Partition Of Dual-Boot Configuration

Bleeping Computer DOES NOT recommend the use of registry cleaners/optimizers for several reasons:? Registry cleaners are extremely powerful applications that can damage the registry by using aggressive cleaning routines and cause your computer to become unbootable.The Windows registry is a central repository (database) for storing configuration data, user settings and machine-dependent settings, and options for the operating system. It contains information and settings for all hardware, software, users, and preferences. Whenever a user makes changes to settings, file associations, system policies, or installed software, the changes are reflected and stored in this repository. The registry is a crucial component because it is where Windows "remembers" all this information, how it works together, how Windows boots the system and what files it uses when it does. The registry is also a vulnerable subsystem, in that relatively small changes done incorrectly can render the system inoperable. For a more detailed explanation, read Demystifying the Windows Registry.? Not all registry cleaners are created equal. There are a number of them available but they do not all work entirely the same way. Each vendor uses different criteria as to what constitutes a "bad entry". One cleaner may find entries on your system that will not cause problems when removed, another may not find the same entries, and still another may want to remove entries required for a program to ... Read more

6 more replies

Hi Everyone,

I recently added a hard drive to my computer (SSD), and installed Windows 7 x64 onto it. The result being a dual boot system, which by default boots to the SSD, and optionally (by Windows Boot Menu), can be booted to the original drive (standard mechanical drive).

Initial setup went fine, however I decided to customize the Windows Boot Menu, so that logical names could be associated with each operating system instance. To do this I used EasyBCD and I altered the names in the Windows Boot Menu from:

Quote:
Windows 7
Windows 7

to...

Quote:
Windows 7 - SSD
Windows 7 - Standard Drive

Shortly after the modification I noticed that I was no longer able to boot into the original OS. Instead I was being presented with a "Repair Windows" option. Figuring that my EasyBCD "tampering" may have had something to do with the issue I decided to change the names back to "Windows 7" in the Windows Boot Menu. However doing so had no positive impact on boot up of the original OS.

After booting again into the original OS I accepted the "Repair Windows" option, and then left the computer over night to do it's "thing". After completion of the "Repair" the situation has deteriorated -

* Windows doesn't load (the same as before)
* Windows doesn't present a "Repair Windows" option (it did before)
* The computer reboots a short period after the &q... Read more

A:Can't boot into original OS after dual boot configuration

The win7 installed on SSD is bootable?
win7 installed on mechanical disk isn't booting?

Please post a full screenshot of "disk management" with all fields visible

6 more replies

Hi Everyone,

I recently added a hard drive to my computer (SSD), and installed Windows 7 x64 onto it. The result being a dual boot system, which by default boots to the SSD, and optionally (by Windows Boot Menu), can be booted to the original drive (standard mechanical drive).

Initial setup went fine, however I decided to customize the Windows Boot Menu, so that logical names could be associated with each operating system instance. To do this I used EasyBCD and I altered the names in the Windows Boot Menu from:
Windows 7
Windows 7
Click to expand...

to...
Windows 7 - SSD
Windows 7 - Standard Drive
Click to expand...

Shortly after the modification I noticed that I was no longer able to boot into the original OS. Instead I was being presented with a "Repair Windows" option. Figuring that my EasyBCD "tampering" may have had something to do with the issue I decided to change the names back to "Windows 7" in the Windows Boot Menu. However doing so had no positive impact on boot up of the original OS.

After booting again into the original OS I accepted the "Repair Windows" option, and then left the computer over night to do it's "thing". After completion of the "Repair" the situation has deteriorated -

* Windows doesn't load (the same as before)
* Windows doesn't present a "Repair Windows" option (it did before)
* The computer reboots a short period after the "Starting Windows" ... Read more

A:Can't boot into original OS after dual boot configuration

Hi All,

Thanks for your assistance. I have sorted the issue...

On installation to the SSD I set the SATA Mode in BIOS to "AHCI", whereas it was originally set to "IDE" when the first Windows installation took place (to the standard mechanical drive)!

After setting the BIOS back to "IDE" I was then able to boot into the first Windows installation (on the standard mechanical drive).

Now I just have to remember to change my BIOS before switching between OS installations.

Kind Regards,

Davo

2 more replies

Windows Vista 64bit
was HP Desktop m8457c
but motherboard died so I purchased
gigabyte GA-880GM-D2H (rev. 3.1)
AMD 880G socket AM3
I updated my memory with PATRIOT gaming i5 8gb DDR3 1333MHz 9-9-9- kit
it is UNGANGED

I had to change CPU to match
it is AMD phenom II X6 1100T black edition
3.3GHz
Everthing worked perfect from Nov 7 until Dec 20
then one morning after internet auto update I found
DMI Pool Data
AMD data change Update new data to DMI!
Boot from CD/DVD
Disk boot failure insert system disk and press enter
I tried many things other have here on this forum
my problem is that in Master 2 is the original HARD DRIVE Slave 2 CD/DVD Master 3 which is the second hard drive, but BIOS sees it as the same hard drive as Master 2. It is a shadow copy of the 1rst HD and is same size.
I have turned each off independently in BIOS, but no OS will boot. Tried original recovery disk with system error not able to recover (BECAUSE OF new motherboard).
HELP

More replies

So I've been using my 64GB ssd as my windows 7 boot drive and i have a 1TB hdd as my data drive. Recently the my computer has begun to freeze up with errors like "explorer.exe" has stopped responding or "windows" has stopped responding and half of the time when i try to boot it says it cant find windows. This has lead me to believe that my ssd is dying despite being only a year old. I need to RMA my ssd but to do that i would be losing my boot drive for weeks. So I thought id try to create a system image so that i can simply put my boot drive on my hdd, but when i try to create the image it says that the image would be 711GB because its including all of my hdd (which contains all my user libraries and downloads). My question is: how do I make windows stop thinking that my hdd is a system drive so that I can create a reasonably sized image, or more generally: how can i easily move my boot drive to my hdd? Also, I've read some posts about using "easyBCD" to accomplish the latter but I'm not sure that's exactly what i need in this situation. If someone can clarify that that would be great too.
Thanks.

A:Moving Boot Data to Data Drive

Hello Astronomicat, and welcome to Seven Forums.

Could you post a screenshot of your Disk Management (diskmgmt.msc) screen show the full layout of all HDDs? This may be able to help determine why it is including more than your 64GB Windows 7 SSD in the system image. Backup Complete Computer - Create an Image Backup
Did you move your page file, user profile folder, or user folders to another HDD/partition location other than the default C: ? If so, then those locations would be included in a system image as well, and cannot be unselected until they are moved back to the default location.

4 more replies

Hi
I have an Intel motherboard D865GBF and in the bios under Boot Configuration is says Plug & Play O/S Yes
Then is says this lets the Operating System control the boot up. My computer boots from the hdd first (C) I want to boot first from the CDrom first just in case my computer goes down and I need Cdrom access for my XP cd. Or does this not matter? Another thing is I have a bootable Linux CD and I can't use it because I can't set my D: (cdrom) to be first. How can I control the boot setup?

A:Boot configuration

Go into your bios. Set the Plug & Play O/S to no. You should then be able to set your boot priority.

Save and exit bios.

Regards Howard

7 more replies