Tech Problem Aggregator

Help with blue screen auto reboot, Stop: 0x0000007B error screen

Q: Help with blue screen auto reboot, Stop: 0x0000007B error screen

Hello, I have an HP Pavilion g series laptop (running win7) that is in a continuous restarting loop. This happened after the computer auto updated (windows update). I do not know what was updated, but now every time the laptop starts up it seems to be in a continuous rebooting loop after the windows logo then a blue flash. I am unable to go into safe mode or any other mode as I keep getting redirected to a page that gives me two options:Launch Startup Repair or Start Windows Normally. Startup repair gives me the same results as trying to run in safe mode.

By turning the auto-restart on system failure off i was able to read what the blue error message, which says:
-

A problem has been detected and windows has been shut down to prevent damage to your computer.

If this is your first time you've seen this Stop error screen, restart your computer. If this screen appears again, follow these steps:

Check for viruses on your computer. Remove any newly installed hard drives or hard drive controllers. Check you hard drive to make sure it is properly configured and terminated. Run CHKDSK /F to check for hard drive curruption, and then restart your computer.

Technical information:
***STOP: 0X0000007B (0xFFFFF880009A9928,0xFFFFFFFFC000000D,0x0000000000000000,0X00000000000000000)

-
Can someone give me advice on how to solve and prevent this problem? I am currently using a different laptop to access this forum.
kodex

A: Help with blue screen auto reboot, Stop: 0x0000007B error screen

Bug Check 0x7B: INACCESSIBLE_BOOT_DEVICE

The INACCESSIBLE_BOOT_DEVICE bug check has a value of 0x0000007B. This bug check indicates that the Microsoft Windows operating system has lost access to the system partition during startup.





Quote:
Cause

The INACCESSIBLE_BOOT_DEVICE bug check frequently occurs because of a boot device failure. During I/O system initialization, the boot device driver might have failed to initialize the boot device (typically a hard disk). File system initialization might have failed because it did not recognize the data on the boot device. Also, repartitioning the system partition or installing a new SCSI adapter or disk controller might induce this error.

This error can also occur because of incompatible disk hardware. If the error occurred at the initial setup of the system, the system might have been installed on an unsupported disk or SCSI controller. Some controllers are supported only by drivers that are in the Windows Driver Library (WDL). (These drivers require the user to do a custom installation.)


Further Reading...
Bug Check 0x7B: INACCESSIBLE_BOOT_DEVICE

1 more replies
Answer Match 85.5%

I uninstalled a program and upon re-start i received the above stop error stating Inaccessible_Boot_Device.
I have tried to boot in safe mode and all of the other F8 options. I got a Black Boot cd and when I tried to boot from the cd I got the A:/ prompt.
I dont know what to do

HELP
 

A:Blue screen Stop Error 0x0000007B

8 more replies
Answer Match 85.5%

Windows XP

This week I downloaded and installed AVG Anti-Virus (Free) and ZoneAlarm (Free) on my Dell desktop. When I turn on my PC I get the blue screen with the following error: ***STOP 0x0000007B (0XBA4C3524, 0XC0000034, 0X00000000, 0X00000000).

I'm unable to access safemode and don't know how to get pass the blue screen. I downloaded a fix to my memory stick but need directions on how to install.

Thanks in advance for help.
Barb
 

A:Stop error 0x0000007B on blue screen

do you have windows xp CD?
 

3 more replies
Answer Match 84.6%

I was reinstalling windows on my computer but the power turned off during the installation so when I restarted the computer to retry the installation I got the blue screen with the error message that said STOP 0x0000007B. I figured the harddrive got damaged when the power went out so i went out and bought a new Seagate Baracuda 500GB SATA harddrive and tried to install windows on it but I got the same error after the cd finished loading all of the files. I next tried disconnecting the harddrive altogether and just tried the install without any harddrives attached hoping that it would load the files but still take me to the next screen which says no harddrives found but instead I got the same error again.
The exact error is:
STOP: 0x0000007B (0xF8981524, 0xc0000034, 0x00000000, 0x00000000)

Any help would be appreciated.
 

A:Blue Screen STOP 0x0000007B - Error Help needed

There should be an option at the beginning of the install process to load the SATA drivers, the Stop error suggests that it's looking for a non-existent drive as once it gets so far, without the SATA drivers it can no longer find the drive.
 

3 more replies
Answer Match 84.6%

So my wife shut down the old COMPAQ with XP SP3 and of course now it will not boot.

No recent hardware changes. Only recent software change was installing Malwarebytes. After MB scan and quarantine of threats, it ran normally for a week but was never shut down until today.

Now, left alone, it would try to boot, then automatically restart repeatedly over and over, showing the black Windows XP screen for just a second. It will not boot in safe mode. It will not boot to last known good configuration. I was able to turn off the automatic restart to read the error message. On the blue screen it read:

"A problem has been detected and windows has been shut down to prevent damage to your computer.

If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps:

check for viruses on your computer.
Remove any newly installed hard drives or hard drive controllers. check your hard drive to make sure it is properly configured and terminated. Run CHKDSK/F to check for Hard Drive corruption. And then restart computer.
Technical Information:
*** STOP: 0x0000007B(0xF78A2524,0XC0000034,0X00000000,0X00000000)"

On another PC, I was able to download and image a .iso file with xp recovery console. After changing the boot order in the BIOS, was able to boot the COMPAQ from the disc and get into recovery console.

I am unsure how to proceed in recovery console (or otherwise) without losing all my data (I gues... Read more

A:Blue Screen STOP: 0x0000007B Error Message

Hi, Lets give it a try.We will need to view the system status from an external environment. You will need a USB drive and a CD to burn. There will be several steps to follow. Download GETxPUD.exe to the desktop of your clean computerRun GETxPUD.exeA new folder will appear on the desktop.Open the GETxPUD folder and click on the get&burn.batThe program will download xpud_0.9.2.iso, and upon finished will open BurnCDCC ready to burn the image.Click on Start and follow the prompts to burn the image to a CD.Next download driver.sh to your USB driveAlso Download Query.exe to the USB drive. In your working computer, navigate to the USB drive and click on the Query.exe. A folder and a file, query.sh, will be extracted.Remove the USB & CD and insert them in the sick computerBoot the Sick computer with the CD you just burnedThe computer must be set to boot from the CDIn some computers you need to tap F12 and choose to boot from the CD, in others is the Esc key. Please consult your computer's documentation.Follow the promptsA Welcome to xPUD screen will appearPress FileExpand mntsda1,2...usually corresponds to your HDDsdb1 is likely your USBClick on the folder that represents your USB drive (sdb1 ?)Confirm that you see driver.sh that you downloaded therePress Tool at the topChoose Open TerminalType bash driver.shPress EnterAfter it has finished a report will be located on your USB drive named report.txtThen type bash driver.sh -afPress EnterYou will be prompted to input a ... Read more

2 more replies
Answer Match 82.8%

I tried to repair install vista home basic, following these rules.
When the computer rebooted during the installation, I got a blue screen with stop error code 0x0000007B (0x81803BA0, 0xC0000034, 0x00000000, 0x00000000).

The computer won't boot in safe mode, nor does the last known good configuration help (I read it somewhere, that the repair install deletes the restore points).

PLEASE HELP!!!

Is Xpress recovery going to help? If so, does it have to be working (how do I know it is???)
Can I check disk from another computer and how???
Any other solution???

Thanks for your help!

Block of flats.

A:Repair Install blue screen with stop error code 0x0000007B

Welcome

If you create a recovery DVD, you may be able to boot to recovery options
Create Recovery DVD

The Vista recovery disk is used to boot Vista when it won't boot - to run Startup Repair, System Restore, access a Command Line, Recover using a Vista Backup Image, etc.
System Recovery Options. Choose an option tht will not cause you to lose your stuff.

If Vista will not start now, boot the Recovery CD to run Startup Repair which automates System Restore as well as numerous other tests including System File Checker which can repair system files which are not corrupted beyond repair.

If Vista still will not start, try booting into Safe Mode to run sfc /scannow to repair System files.
Special Thanks Given to Seven Forums.
Below is a bulletin distributed by MS to explain the start up procedure when Windows will not boot.
Startup Repair. Startup Repair is a Windows recovery tool that can fix certain problems, such as missing or damaged system files, that might prevent Windows from starting. Startup Repair is located on the System Recovery Options menu, which is on the Windows Vista installation disc. If your computer has preinstalled recovery options, it might also be stored on your computer's hard disk. For more information, see Startup Repair: frequently asked questions and What are the system recovery options in Windows Vista? If your computer does not include Startup Repair, your computer manufacturer might have customized or replaced the tool. Check the informati... Read more

3 more replies
Answer Match 82.2%

I have a Dell computer running Windows 2000. I received the following message when trying to boot up my computer:

Check for viruses on your computer, remove any installed hard drive or hard drive controllers. Run chkdsk/f to check for hard drive corruption and then restart your computer. ***STOP: 0X0000007B (0X8207AA10,0XC0000032,0X00000000,0X0000000) INACCESSIBLE_BOOT_DEVICE

I am unable to get past this screen each time I boot up, so I am unable to run Chkdsk/f. In addition, I do not have any newly installed hard drives. In searching through some of these posts, I've tried F8 and F11 options with no success.

I do not have the original start up disk. What our my options? I am definitely not a computer expert....Thank you in advance for your help!!
 

A:Error Message: Cannot start computer --> get blue screen ***STOP: 0X0000007B (0X8207A

According to Microsoft this can be caused by many different things. Take a look at the following address.

http://support.microsoft.com/kb/822052
 

2 more replies
Answer Match 107.94%

hi there,

Built my first PC yesterday. Spec as follows:

coolmaster 500w PSU

AMD dual core 4600

corsair value RAM 1GB DDR2 PC5300

250GB SEAGATE barracuda sata II 300

ASUS M2N-E SLI GREEN motherboard

geforce 8800 320mb.

Worked on first attept at turining it on. installed XP last night without any problems. Got it verified and then began downloading updates once i had some AV running. As soon as i had to do my first restart the PC refused to go into windows again. It came up with this screen:

I did get into windows via safe mode twice i tihkn but couldn't find the problem.

Then it just refused to even go in via safe mode.

Spoke ot a techno mate and we decided a full format had to be done!

did that last night and all installed fine. So as it was late, i turned the PC off.

This evening i burnt a cd with AV and firewall to install prior to getting on the net. Turned on the PC and went straight into windows, no issues at all.

Installed my firewall and AV, did the restart and i went back to the sae mblue screen as above.

The PC loads up to the bit where it says 'XP' with the little green bar moving across showing it is loading (i have pre SP2.) but loads for about twice the normal time and then goes straight to the blue screen.

I have moved the RAM to all the different slots and tried it but still get the same problem.

Anyone got any ideas as i am at a loss!
 

A:blue screen ''stop: 0x0000007B'' help.

16 more replies
Answer Match 107.94%

HELP Blue screen STOP: 0x0000007B

I dont know what to do?? I cant reboot the computer, everytime I reboot, this blue screen shws up again and again?

Its telling me to to a run CHKDSK /F for hard drive corruption?? or a virus?? what should I do??

THANKS>>>

A:Help Blue Screen Stop: 0x0000007b

Please let us know the exact error message that you received. Here's a link that explains more about this: http://www.bleepingcomputer.com/forums/t/40108/how-to-use-event-viewer/Here's some information about the STOP 0x7b error:http://aumha.org/win5/kbestop.php#0x7bThis is primarily a problem with your hard drive, but may also be due to corruption of the drivers that run your hard drive. CHKDSK /F /R will help to detect some problems with the hard drive.Are you able to get into Windows? If not, there are several ways to try and fix this problem:1) Use the Recovery Console to run "fixboot" and maybe even "fixmbr"2) Performa a repair install of Windows XP3) Run Digital Dolly to see if you can check your hard drive status4) Download the diagnostic software from the hard drive manufacturer's website.If all of this fails, then you may need a new hard drive - but don't rush out and get one until you let us know how the troubleshooting is working.

4 more replies
Answer Match 107.94%

ive got the blue screen screen stop msg. 0x0000007B ?
i have a dell notebook about 4 yrs old win xp home op system
purchased in u.k. so when i called dell.ca they would not help me only direct me to uk tech support and the guy there told me fault showing up as 'not enough memory' "56mb".
he said a quick fix would be to restore to factory settings (cost bout $60) and then go purchase more memory
as i cant get past this blue screen or do anything was hoping someone here might be able to help with restore (i guess if i do the restore i will loose all my files) or do i have any other options before i have to take it to my local pc repair store and pay however many $$.

thanks jezza.
 

More replies
Answer Match 107.94%

Hello
I have laptop HP pavilion dv5 with vista
I am tring to install XP :slurp:
but a blue screen accures and stop formating procces !!







A problem has been detected and windows has been shut down to prevent damage to your computer.
If this is the first time you?ve seen this stop error screen , restart your computer . If this
screen appears again , follow these steps :
check for viruses on your computer , remove any newly installed hard drivers or hard drive controller.
check your hard driver to make sure it is prply configured an teminated. Run CHKDSK /F to check for hard drive corruption ,
an then restart your computer.

Technical information :
*** STOP : 0X0000007B ( 0XF78DA524,0XC0000034,0X00000000,0X00000000)Click to expand...

Plz Help
 

A:Blue Screen STOP: 0x0000007B

a DV5 hey?
Hmm have a look here: http://h20180.www2.hp.com/apps/Look...ion+dv5-1000+Entertainment+Notebook+PC+series
Select your model (from the 291 products) and check for any harddrive controller drivers to install with XP (press F6 key during the initial Windows setup)
 

8 more replies
Answer Match 107.94%

Hey Guys,

I have an HP Compaq NC6320 laptop and I'm having some major problems with it.

I currently have a Weston Digital WD1600BEVT 160GB Sata 2.5" drive installed, with 1.5GB DDR2 RAM.

i tried installing XP Pro and I have been getting blue screens with all kinds of stop messages.

Basically the laptop gets to 100% of install, then reboots to start the windows based install and it blue screens with this error.

I ran Memtest which didnt show any faults, then downloaded the WD Data Lifeguard Diag system - ran the quick test and passed, ran the extended test and passed then formatted with 0's which passed.
Pulled the DVD drive and replaced that, and changed the XP disc I was using (I have 4 different discs).

Tried install again, same fault - pulled the memory and installed new memory - ran memtest again, no fault, tried install again and same fault....

The only thing I havent done is replace the HDD but I dont have a spare floating about so just wondered is this likely to be the HDD even though the test shows no fault, or is this going to be something much worse?

Thanks in advance
 

A:blue screen ''stop: 0x0000007B'' help.

The problem may be related to SATA Native Mode.

To disable SATA Native mode:

-------------------------------------------------

Upon booting, Enter the setup menu (F10)

==> System Configuration

==> Device Configurations

==> SATA Native Mode - Disable it

-------------------------------------------------
Save your settings and reboot. You should be able to install XP now. After installation, you can enable it back.

Post back with results.
 

2 more replies
Answer Match 107.94%

Desktop  dell XPS 400  windows XP media center  SP3
 
problem:
 
Following a virus scan/removal reboot  recieved BSOD   STOP: 0X0000007B (0XF7A6D524, 0XC0000034, 0X00000000, 0X00000000)  upon rebooting brings up start in Safe Mode screen trying all options seperatly brings me rigth back to BSOD with same codes. ran diagonostics from cd all passed,  ran chkdsk /p /r  no errors found, however BSOD recommends CHKDSK /f  but recovery console has no /f option.   also ran bootcfg /rebuild and recieved error can not complete scan due to corrupt files run chkdsk
 
been told hardware issue,  also told nopt hardware software issue

A:Blue screen stop: 0x0000007b

Try running chkdsk /r.   Start/Run...type chkdsk /r and hit Enter.  Type Y in new screen, hit Enter.  Reboot the system, the command will execute...on completiion, the system will automatically try to boot into Windows.
 
Alternatively...to run chkdsk /r from the recovery console...just enter the command chkdsk /r, without any additional modifications.
 
AFAIK, there is no such command as chkdsk /p /r...chkdsk /p is the command for running a read-only command (with no attempted repair), while chkdsk /r is the most complete chkdsk command and attempts to do everything that chkdsk /f does, while also attempting to recover file data which may be in bad sectors.
 
Louis

2 more replies
Answer Match 107.94%

Hey Gang!

My problem is with my windowsXP. When I boot up I get a Blue Screen, with
the message: ***Stop: 0x0000007B (0xfe233640,0xc0000034,0x00000000,
0x00000000). Folks what if anything can I do???
 

A:BLUE SCREEN***Stop:0x0000007B

Stop Error 0x0000007B
Stop error number:
(0x0000007B)

Descriptive text:
INACCESSIBLE_BOOT_DEVICE

Usual cause:
Initialization of the I/O system failed (usually the boot device or the file system).
To troubleshoot Stop error 0x0000007B
1.
A boot sector virus frequently causes this Stop error. Using a current version of your antivirus software, check for viruses on your computer. If you find a virus, perform the steps required to eliminate it from your computer. See your antivirus software documentation for these steps.

2.
Remove any newly installed hardware (RAM, adapters, hard disks, modems, and so on).

3.
Check the Microsoft Hardware Compatibility List to verify that all your hardware and drivers are compatible with Windows 2000.

To see the most recent version of the HCL, visit the Microsoft Web site:

http://www.microsoft.com/whdc/hcl/default.mspx

4.
If you're using a SCSI adapter, obtain the latest Windows 2000 driver from the hardware vendor, disable the sync negotiation for the SCSI device, verify that the SCSI chain is terminated, and check the SCSI IDs of the devices. If you're unsure how to do any of these steps, refer to the device documentation.

5.
If you're using IDE devices, define the on-board IDE port as Primary only. Check the Master/Slave/Only settings for the IDE devices. Remove all IDE devices except for the hard disk. If you're unsure how to do any of these steps, refer to your hardware documentation.

6.
If the computer ... Read more

2 more replies
Answer Match 107.94%

I'm getting a blue screen with the following message:

A problem has been detected and windows has been shut down to prevent damage to your computer.

If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps:
Check for viruses on your computer. Remove any newly installed hard drives or hard drive device controllers. Check your hard drive to make sure it is properly configured and terminated. Run CHKDSK/ F to check for hard drive corruption, then restart your computer.

Technical Information:
STOP: 0x0000007B (0xBA4C3524, 0xC0000034, 0x00000000, 0x00000000)

I'm not able to go back to latest good configuration in Safe Mode or run the CHKDSK/ F, it just goes back to this screen. I have no idea how to proceed, so any help you can offer is very much appreciated!

Thanks!!

A:STOP: 0x0000007B Blue Screen

System manufacturer and model?

FWIW: Even though the suggestion is for chkdsk /f, you should run chkdsk /r (includes chkdsk /f functions).

Louis

7 more replies
Answer Match 107.52%

Blue screen stop error happens randomly. When it happen the windows will reboot, then the home page will changed to a website which I never see before. I am using an NEC noteboot Versa E6000. I have uploaded the minidump. Please help me analysize it.
 

A:My winxp has blue screen stop error then reboot

Hello and welcome to Techspot.

Your minidumps are crashing with various .sys files, such as bvlgs.sys/e2emf47.sys/dj9mx7.sys etc. I can`t find any info for these files.

Your minidumps also reference rasphone.exe, as the process that was running when the crashes occured. This is the Remote Access Phonebook.
Product Name: Microsoft® Windows® Operating System.

Your minidumps crash with a bugcheck of D1.

0x000000D1: DRIVER_IRQL_NOT_LESS_OR_EQUAL

The system attempted to access pageable memory using a kernel process IRQL that was too high. The most typical cause is a bad device driver (one that uses improper addresses). It can also be caused by caused by faulty or mismatched RAM, or a damaged pagefile.

Just in case you`ve got a damaged page file do the following.

Right click my computer, and select properties, and then the advanced tab.

Under performance, click settings. Click on the advanced tab, and then on the change button.

Click on the custom size button, and click in the initial size box and make the size of the page file 0. Click in the maximum size box, and make the size of the page file 0.

Click set.

Now reboot your machine. After your system has restarted run a defrag.

Once the defrag has finished, go back to the pagefile settings above, and click on the change button. For the initial, and maximum pagefile size make it 1.5 times the ammount of ram your have. I.E if you have 512mb of ram set the page file to 768mb.

Click on t... Read more

2 more replies
Answer Match 106.68%

Hi all,

I've got a strange one for you today....

I have 4 or 5 year old Win XP Home Tiny desktop computer which is having trouble booting. Basically when booting up, right before the Win XP logo it reboots itself.

I have disconnected all IDE devices except for the master hard drive (plus disabled them in BIOS), I have tried a different hard drive in the machine that I know is working and has XP Pro installed. The same thing happens with this hard drive - reboots. This hard drive also has Ubuntu installed, and the machine happily boots Ubuntu to the normak desktop, but for some reason won't boot XP!

Also tried a third hard drive in this machine that is working with Win 2000 installed, again the same thing happens.

Next I tried the original hard drive in a working seperate machine which produces the same result again.

Also tried removing the RAM from the original machine and inserting a stick of working RAM from my other machine which again makes no difference.

All hard drives I've tried have the correct jumper setting (primary master).
Also tried putting the Win XP disc in the drive and booting to that, I get to the menu and try to do a repair (R), but a few seconds after the repair begins the system reboots (this is using the original hard drive).
Also tried booting into safe mode, and last known good config on all drivers.

The hard drive is being detected in POST and in the BIOS which I have set as the first (and only) boot device.

When I turn o... Read more

A:XP blue screen when boot, STOP 0x0000007B

15 more replies
Answer Match 106.68%

Hi, I have got a major problem that I hope someone can help me deal with. I’ve been having random system crashes for sometime and I decided I will try and sort them out, but ive only made things much worse. The instructions I was using recommended that I update my motherboard bios, so I did. However when I restarted I got this message after windows come on to its loading screen for a second:-
“A problem has been detected and windows has been shut down to prevent damage to your computer.

If this is the first time restart, if not do this:

Check for viruses, remove newly installed hard drive or hard drive controllers, check your hard drive to make sure it properly configured. Run CHKDSK /F to check for hard drive corruption.

Tech Info:

***Stop: 0x0000007B (0xf7c46524,0xc000034, 0x00000000, 0x00000000)”

So far I’ve tried removing the battery in the motherboard but that hasn’t made any difference.
Specs:
Windows XP Pro
Intel Pentium D 805 (2x2.66GHz) 64Bit Socket 775 Dual Core 2MB
ASRock CONROEXFIRE-ESATA2 SKT775 945P
MSI 7600GS 256MB DDR2 TVO
Corsair 1GB DDR2 667MHz/PC2-5400
 

A:Blue Screen Upon Start Up. Stop: 0x0000007B

I found this on microsoft hope your computer is xp. http://support.microsoft.com/kb/324103
edit... here is some more stuff I seen.

A BSOD can also be caused by a critical boot loader error, where the operating system is unable to access the boot partition due to incorrect storage drivers or similar problems. The error code in this situation is STOP 0x0000007B (INACCESSIBLE_BOOT_DEVICE). In such cases, there is no memory dump saved. Since the system is unable to boot from the hard drive in this situation, correction of the problem often requires booting from the Microsoft Windows CD. After booting to the CD, it may be possible to correct the problem by performing a repair install or by using the Recovery Console (with CHKDSK).
 

3 more replies
Answer Match 106.68%

After installing a brand new hard drive on my PC,i've been attempting to install XP Professional as my OS. After multiple attempts in the last 24 hours i keep getting this STOP:0X0000007B(0XF7C85528,0XC0000034,0X00000000,0X00000000) message. However,when i installed the XP Home Edition,it loaded and booted right up. I have a 320GB hard drive and i want to run 2 OS's. XP Home on one partition and XP Professional on the other. I have tried installing it on a FAT32 partition and an NTSF partition. I've formatted the drive both ways with the quick and slow format. Is it possible the install CD is bad?
 

More replies
Answer Match 106.68%

Hi, I have got a major problem that I hope someone can help me deal with. I?ve been having random system crashes for sometime and I decided I will try and sort them out, but ive only made things much worse. The instructions I was using recommended that I update my motherboard bios, so I did. However when I restarted I got this message after windows come on to its loading screen for a second:-


?A problem has been detected and windows has been shut down to prevent damage to your computer.

If this is the first time restart, if not do this:

Check for viruses, remove newly installed hard drive or hard drive controllers, check your hard drive to make sure it properly configured. Run CHKDSK /F to check for hard drive corruption.

Tech Info:

***Stop: 0x0000007B (0xf7c46524,0xc000034, 0x00000000, 0x00000000)?

So far I?ve tried removing the battery in the motherboard but that hasn?t made any difference.


Specs:
Windows XP Pro
Intel Pentium D 805 (2x2.66GHz) 64Bit Socket 775 Dual Core 2MB
ASRock CONROEXFIRE-ESATA2 SKT775 945P
MSI 7600GS 256MB DDR2 TVO
Corsair 1GB DDR2 667MHz/PC2-5400

A:Blue Screen Upon Start Up. Stop: 0x0000007B

This is almost certainly due to upgrading your BIOS. First, backup your data and Registry to a second disc or CD/DVD just in case of any problems.

Configure your BIOS so that CDROM is the first boot device.

Insert the Windows XP installation CD then restart your computer.

When the "Press any key to boot from CD" message appears on the screen, press a key to start your computer from the Windows XP CD.

You will then get a 3 item menu:

To setup Windows XP now, press ENTER.

To repair a Windows XP installation using Recovery Console, press R.

To quit Setup without installing Windows XP, press F3.

Press ENTER.

On the Windows XP Licensing Agreement screen, press F8 to agree to the license agreement.

Select your current installation of Windows XP in the box, and press R to repair Windows.

Follow the instructions that appear on the screen to reinstall Windows XP.

After you repair Windows XP, you may have to reactivate your copy of Windows XP.

2 more replies
Answer Match 106.68%

I am running Windows 2000 Professional on an HP Omniboox XE3 GC (P3, 850 MHz, 512 MB RAM). I was having problems with the Roxio Easy-CD Creator software (for my external CD burner), and I uninstalled it, with the intention of reinstalling it. When I rebooted my laptop, it seemed to start properly upto the midway stage of the Windows 2000 splash screen - and then a BLUE SCREEN appears with the following message:

STOP: 0x0000007B (0xEB82784C, 0xC0000034, 0x00000000, 0x00000000)
INACCESSIBLE_BOOT_DEVICE.

I tried pressing F8 during the startup and then going to 'Safe Mode' etc but none of the options worked, including starting with 'Last Known Good Configuration'.

I then created 4 Windows 2000 Professional Setup disks, pressed 'Esc' during startup, and booted from these disks. I then clicked on 'R' to repair the Windows 2000 installation. There were 2 options provided after this: (1) To repair Windows 2000 using the recovery console by pressing 'C', and (2) To repair Windows 2000 by using the emergency repair process by pressing 'R'.

I first tried the second option (2). There were two options after this, one for a Manual Repair (press M), and the other for a Fast Repair (press F). I pressed 'M', selected all the 3 repair options available (Inspect startup environment, Verify Windows 2000 System files, Inspect boot sector), and pressed Enter. It then asked me to press Enter again if I had the 'Emergenc... Read more

A:Help!!! INACCESSIBLE_BOOT_DEVICE. STOP: 0x0000007B blue screen!!!Help!!!

16 more replies
Answer Match 106.68%

I've been trying to play Medieval II total war and recently my computer has been restarting when the game tries to load. This has also happened to me with Last Chaos. I scanned my drives...no problems there i think. No viruses to my knowledge...and all my drivers are up to date. Attached are the minidumps. Please help if you have any idea of whats going on.
 

A:System crash and reboot stop/blue screen error

Try using the Omega Drivers. http://www.omegadrivers.net/ati_winxp.php

Blaming the CCC. http://www.techspot.com/vb/topic113038.html

BugCheck 1000008E, {c000001d, e50af7c0, a74dc88c, 0}
Probably caused by : ati3duag.dll ( ati3duag+11a5c8 )
 

2 more replies
Answer Match 105.42%

Hello, I am new to these forums and I have just a little bit of knowledge about computers. Hopefully enough that I can follow instructions! I think this is the correct forum as my issues started after some sort of bot was detected on my computer, so I think that something has infected my computer.

Here is the situation:
Computer: Dell Dimension 3100 from 2006 running Windows XP Media Center Edition
AVG (free version) and RU Botted (Trend Micro) both run on this computer. I also have MBAM downloaded and do occasional scans with it, as well as SpyBot Search & Destroy.

Yesterday afternoon while web-browsing in IE I got a small pop-up in the lower right corner, from RU Botted indicating that a Bot had been detected. It said the BOT could not be removed. It all happened fast so I did not catch the name of the Bot. All programs open on my computer began to shut down. I panicked and here is where I did something that probably did not help - instead of letting the computer finish shutting itself down I just hit the power button to instantly turn it off.

I can now no longer get my computer up and running. Upon starting I get the Dell screen (and can get into the Set-Up or Boot menus) and then I get a black screen with the choices of how to start my computer (Safe Mode, Safe w/Networking, Safe Mode w/Command Prompt, Last Known Good Config, and Start Windows Normally).

If I try any of the Safe Mode options I get a bunch of info scrolling by and then the Blue Scr... Read more

A:Blue Screen Stop: 0x0000007B, computer won't boot

Hello and welcome to Bleeping ComputerMy name is etavares and I will be working with you to fix your computer.Please take note:If you have since resolved the original problem you were having, we would appreciate you letting us know. Please tell us if you have your original Windows CD/DVD available.If you are unable to perform the steps we have recommended please try one more time and if unsuccessful alert us of such and we will design an alternate means of obtaining the necessary information.Once we start working together, please reply back within 3 days or this thread may be closed so we can help others who are waiting. If you will be unable to respond (e.g. vacation, travel, etc.), please let me know ahead of time.Please refrain from running tools or applying updates other than those we suggest while we are cleaning up your computer. The reason for this is so we know what is going on with the machine at any time. Some programs can interfere with others and hamper the recovery process. Please also continue to work with me until I give you the all clear. Even if your computer appears to act better, you may still be infected.It sounds likely that you have a backdoor rootkit that infected the Master Boot Record. We can hopefully recover. Do you have a clean computer and an empty USB flash drive? We can create a bootable environment to boot the infected computer from the USB flash drive and work through the error; or at least access your files.

89 more replies
Answer Match 105.42%

Cannot start computer --> get blue screen ***STOP: 0X0000007B (0X8207AA10,0XC0000032,0X00000000,0X0000000) INACCESSIBLE_BOOT_DEVICE

I've tried all the F8 options without success. I cannot get started to check anything, I'm just stuck with nowhere to go. I've just relocated the Dell Dimension 4100 from work to home. It started up fine last night but when I moved it into it 's final location, I'm getting the BLUE SCREEN at the Windows start-up. The message says to check for viruses, remove any newly installed hard drive or hard drive controllers, check for hard drive corruption and that it is properly configured. How do I check if I can't boot? I've added or altered nothing except moving it to a different location and I don't have the original start-up disk since I aquired it from work as a "give-away".

Any suggestions?
 

A:Windows 2000 blue screen STOP 0X0000007B

Sounds like something's come loose. If you've never been into a tower before make sure you discharge any static or it'll fry the motherboard. Make sure everything's turned off and check cables etc and phericals in slots.

If all else fails the f key to press is F11 which will give you options to reset to factory settings.
 

3 more replies
Answer Match 104.16%

I'm not actually trying to install a new Windows,What might be the cause to this problem and what are the solution to fixing it? Thanks ahead.

A:Blue Screen STOP = 0x0000007B Dell Latitude E6430s

It isn't clear what the problem is - are you in fact reloading the OS?  Or does the blue screen come up spontaneously?  If so - when?  At boot?  At random?
The leading suspects for blue screen stops are failing hard drives or bad RAM - run an extended system diagnostic (F12 at powerup).  If you require further information, post any error codes that arise.

1 more replies
Answer Match 104.16%

My son has just dropped his desktop off saying it won't start!

It won't even boot up in Safe mode, looks like he may have a virus of some description.

After selecting safe mode, the screen goes blue and gives an error message:

*** STOP: 0x0000007B (0xF78A2524,0xC0000034,0x00000000,0x00000000)

Any suggestions how I can fix this????

Cheers

Paul.

A:Computer wont start, Blue screen STOP:0x0000007B

FWIW: 7B errors often occur when users have tried to either clean install or repair install Windows, IMO. So the error in itself is not necessarily significant.Some details about what occurred with the system before the cry for help by your son...would be of greater benefit than focusing on that error message, IMO.You might gain by reading STOP 7B Errors .You might also take a look at 7B, left column at http://www.aumha.org/a/stop.htm , to see the complexity involved in trying to determine cause of that particular error.Louis

8 more replies
Answer Match 102.9%

I have been searching for the past 4 days on how to fix my computer and cant seem to find anything that helps me. Here is play by play of what i did...My Lime Wire Pro was not working so i uninstalled and reinstalled to try to fix it, it still wouldn't work so i took the program completely off and downloaded the regular Lime Wire, i downloaded a few songs one of which was a virus but my anti-virus caught it and removed it before it had a chance to completely download. Everything was working fine afterwards until i shut my computer down and went to turn it on the next morning which is when i got the first blue screen. That basically told me to remove any newly installed software so i went into the F8 screen and started windows in safe mode, removed lime wire and ran the anti-virus and spy bot...nothing was found. I then restarted and it brought me to another blue screen. I have tried everything i can possibly think of. I have tried ALL of the windows advanced options F8, F2 and F12 and nothing will let me get into windows. This is EXACTLY what the blue screen says:A problem has been detected and windows has been shut down to prevent damage to your computer.If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps:Check for viruses on your computer. Remove any newly installed hard drives or hard drive controllers. Check your hard drive to make sure it is properly configured and terminated. Run C... Read more

A:Stop Error Screen- Stop: 0x0000007b (0xf8a0e528, 0xc0000034....

Try running chkdsk in Safe Mode.Right click on the C drive in Explorer and go Properties > Tools > Check Now (under Error Checking). Check both boxes then click "Start Now". A message will pop up saying that Error Checking will run after you restart the computer. Restart the computer and Error Checking will run automatically after the restart. After it?s finished it will restart into Windows automatically.

3 more replies
Answer Match 102.06%

hi all. i have dell inspiron 1545 , windows vista . i have a blue screen, STOP Error 0x0000007b ( windows recovery error ). a recent software or hardware change may cause . i am unable to reboot . even when i use dvd for re-installation, again same sceen is poping up, even i choose safe mode same blue screen is poping up. i do not have any option . i am unable to passthe system recovery error screen . please help if anyone has information
 

More replies
Answer Match 98.7%

Hi,
I've a DIY PC that often reboot by itself. When I bought this PC, it worked fine for a year.
The initial problem was it crashed & reboot after the OS is started for a while. The reboot became so frequent that I have to take it back to the shop. The owner just took out the RAM and wipe it and the PC works fine for some months. Unfortunately the same problem repeated after some months and I have to take out the RAM and wipe it to let it run normally.
Now the problem has gone more severe. Not only wiping the RAM doesn't solve the problem, I have even install a clean OS to test if it was caused by my OS, but the new OS also crashed and reboot after a while.
The reboot occurs after shortly the OS is started. Sometimes the crash can happen continuously until the OS can't boot. Usually when this happen, I'll boot with my second disk (with a clean OS) and the PC tends to work for a while, although the second disk still crash occassionally after running a short while.
Since the motherboard is MSI, I did a live scan with the MSI website to update its firmware or drivers. Unfortunately the website return showing the firmware is up-to-date.
Can someone enlighten me what could be the problem please? By the way the OS is Windows XP. I've also tried installing XP and Windows 7 as a clean OS for testing and the reboot still persists.

Thanks in advance for your guidance.

A:Blue screen and auto reboot

Your description may indicate a memory fault or incompatibility. Provide the following information about your hardware so we can check compatibility:Download and install CPU-Z and Upload screenshots of the CPU, Mainboard, Memory, and SPD tabs. In the SPD tab, upload an image of each slot. To upload all screenshots, it would be best to:generate the images using the Snipping Tool,
go to where the images are saved,
right click in a blank area within the folder where the images are saved,
create a new folder,
name the folder CPUZ,
select all the images,
place the pointer over an image,
press and hold down the left mouse button and drag the image (all images should move with it),
drop the images into the CPUZ directory you created,
create a compressed (zipped) folder of CPUZ
upload the .zip file to the forums.
Run some memory related diagnostics:
Quote:




NOTE:If you are overclocking any hardware, please stop.





Run display device memory tests to check the display card for memory problems.Display device memory tests
Run Memtest86+ for at least 7-10 passes. It may take up to 22 passes to find problems. Make sure to run it once after the system has been on for a few hours and is warm, and then also run it again when the system has been off for a few hours and is cold.Test RAM with Memtest86+
Run Prime95 to test your CPU, RAM modules, and general hardware.Prime95 Hardware Stress Testing Steps

-----

13 more replies
Answer Match 97.86%

I'm having an issue that I've been working on for a while and its driving me nuts. I caught a virus a few weeks back (I think, couldn't actually find one) that filled up my C drive to capacity. I decided to just reformat and reinstall XP but everytime I try I get a stop error 0x0000007b. I googled it but haven't really gotten anywhere because I don't think its a harddrive or a driver issue and I'm a bit leery of playing around with flashing my BIOS.

I know it isn't my harddrive because I removed it and tested it with another and am getting the same error. I also checked my BIOS settings, with only one harddrive I don't use RAID (altho it is an option) so I don't think its a driver issue. I was able to install Linux and now I'm running Vista, although I don't really know what that tells me except that everything physically seems to be working fine. Also, I've twice now gotten a 'boot disk failure, insert system disk...' error prior to Vista starting up and then after I restart it worked fine again.

Sorry I don't have the exact specs on my computer. The motherboard is a Gigabyte with a 3ghz Pentium D chip with 1 Gig of ram (1 stick). Both harddrives I tried were western digital (one a 40 gig, the other was a 160, both IDE drives). At this point I don't even know if its a software or hardware problem - not too good with computers, so any help would be appreciated! Thanks!!
&nbs... Read more

A:blue screen / 0x0000007b error while reinstalling xp

you could try resetting the mobo - look up the reset jumper pins in the mobo manual or on the net if you can get to it and short them as shown for a few secs.
Hope this helps
 

5 more replies
Answer Match 97.86%

Yesterday my laptop crashed when I put my iPod touch in to sync, I had to leave it but my mum decided to turn it off when it wouldn't do that she removed the battery and since then it has just come up with the acer startup repair, I decided to install xp back onto my laptop to get it to work. But all that's happened is it gets part a blue load up screen then bit of the way through it goes to the blue error screen and comes up with the following code : 0x0000007b. Is there any way I can fix this?

A:Blue screen error code 0x0000007b

In most cases this is a result of not having the proper drivers for the SATA hard drive.
Please post the exact make and model of your laptop so we can look stuff up.

3 more replies
Answer Match 97.86%

Hi all. I'm posting here because the hdd is most likely causing the problem.

I put together a pc. Everything is new except the hdd, cd rom, and floppy. It turns on, i can get into bios, but if I don't choose to get into bios a few secs later I get this blue screen error-
0x0000007B(0XF78AE640,OXC0000034,0X00000000,0X00000000). It says that there was a problem and the computer has been turned off to protect from damage, etc. Then it gives the above number and says to check for viruses on hdd, check hdd and hdd controllers, and to remove any new hardware.

I think that the cause of the problem is that there were too many hardware changes done at once or windows doesn't have the drivers for the new hardware. This is a hdd from my other computer, and right now I have Windows XP Pro installed.

So, how can I fix this? I mean..I know there has to be a way to install a hdd from another computer. Thanks.
 

A:0x0000007B Blue Screen Error at Bootup

Unfortunately, there is no simple way to transfer an HDD from one motherboard to another. Most savvy people wouldn't even dare it.

This is exactly the behavior to expect from such an upgrade.

If you want to keep trying, see if you can go into Safe Mode by pression "F8" just before the Windows logo appears.
If you can get into Safe Mode, you'll have to get into Device Manager and remove all the hardware of your old stuff. As well as any startups relating to old hardware.

Basically, XP has to rebuild its driver information, its HAL, and other such files. If it can't, well, you see here.

Backup and reload is the best option.
 

3 more replies
Answer Match 96.6%

When I shutdown my computer it last about ten minutes and then I have a blue screen with "Driver_Power_State_Failure", minidump of the memory and auto reboot.

Please find in attachment two exemples of what I got when the problem occurs.

A:Windows 7 - shutdown with blue screen and auto reboot

Hi -

Update these 3 drivers to start -

Code:

btkrnl.sys Fri Oct 01 17:48:29 2004 (415DD0AD)
btslbcsp.sys Fri Oct 01 17:50:18 2004 (415DD11A)
SABI.sys Thu May 28 02:38:10 2009 (4A1E3152)

System information needed --> BSOD Posting Instructions

Attach the resulting zip files to your net post.

After driver updates, run --> DRIVER VERIFIER - Windows 7 & Vista

Regards. . .

jcgriff2

.



BSOD BUGCHECK SUMMARY
Code:

Built by: 7600.16539.x86fre.win7_gdr.100226-1909
Debug session time: Sat Jul 17 16:54:52.365 2010 (GMT-4)
System Uptime: 0 days 5:15:51.145
BugCheck 9F, {4, 258, 85a6ea70, 83125b24}
Probably caused by : memory_corruption
BUGCHECK_STR: 0x9F
PROCESS_NAME: System
??????????????????????????????????????????????????????????????????????????????????????``
Built by: 7600.16539.x86fre.win7_gdr.100226-1909
Debug session time: Sat Jul 17 11:35:03.739 2010 (GMT-4)
System Uptime: 0 days 6:27:32.518
BugCheck 9F, {4, 258, 85a6da70, 8313bb24}
Probably caused by : memory_corruption
BUGCHECK_STR: 0x9F
PROCESS_NAME: System

3 more replies
Answer Match 96.6%

Hi guys asking for a little help because im totally clueless... As stated in the title my pc randomly freezes without any cause that im aware it happens mostly when i am gaming but also when i search the web or watch a tv show or film.
I don't think its even creating mini-dumps.

I could not get perfmon/report to run ive added a screenshot of what i got when i ran perfmon incase i did something wrong

Thank You
Ricky

Pc stats:

Field Value
Computer
Computer Type ACPI x64-based PC
Operating System Microsoft Windows 7 Ultimate
OS Service Pack -
Internet Explorer 9.0.8112.16421 (IE 9.0)
DirectX DirectX 11.0

Motherboard
CPU Type QuadCore Intel Core 2 Quad Q8200, 2333 MHz (7 x 333)

Motherboard Name ASRock G41M-S3 (2 PCI, 1 PCI-E x1, 1 PCI-E x16, 2 DDR3 DIMM, Audio, Video, LAN)
Motherboard Chipset Intel Eaglelake G41

DIMM1: Corsair Vengeance CMZ4GX3M1A1600C9 4 GB DDR3-1333 DDR3 SDRAM (9-9-9-24 @ 666 MHz) (8-8-8-22 @ 592 MHz) (7-7-7-19 @ 518 MHz) (6-6-6-16 @ 444 MHz)
DIMM3: Corsair Vengeance CMZ4GX3M1A1600C9 4 GB DDR3-1333 DDR3 SDRAM (9-9-9-24 @ 666 MHz) (8-8-8-22 @ 592 MHz) (7-7-7-19 @ 518 MHz) (6-6-6-16 @ 444 MHz)


Display
Video Adapter NVIDIA GeForce GTS 450 (1048256 KB)
Video Adapter NVIDIA GeForce GTS 450 (1048256 KB)
3D Accelerator nVIDIA GeForce GTS 450
Monitor Generic PnP Monitor [NoDB] (1)

I got all this from AIDA64
If you need anything else let me know

A:Pc freezing randomly no blue screen and no auto reboot

You have not generated any .dmp files since May 9th, but your previous crashes from early last month may be helpful. They were all Video TDR Error crashes:







  
Quote: Originally Posted by H2SO4


These are all stop 0x116 VIDEO_TDR_FAILURE conditions.

It's not a true crash, in the sense that the bluescreen was initiated only because the combination of video driver and video hardware was being unresponsive, and not because of any synchronous processing exception.

Since Vista, the "Timeout Detection and Recovery" (TDR) components of the OS video subsystem have been capable of doing some truly impressive things to try to recover from issues which would have caused earlier OSs like XP to crash. As a last resort, the TDR subsystem sends the video driver a "please restart yourself now!" command and waits a few seconds. If there's no response, the OS concludes that the video driver/hardware combo has truly collapsed in a heap, and it fires off that stop 0x116 BSOD.

If playing with video driver versions hasn't helped, make sure the box is not overheating. Try removing a side panel and aiming a big mains fan straight at the motherboard and GPU. Run it like that for a few hours or days - long enough to ascertain whether cooler temperatures make a difference. If so, it might be as simple as dust buildup and subsequently inadequate cooling.


The above quote was taken from http://www.sevenforums.com/cr... Read more

5 more replies
Answer Match 96.6%

So my wife shut down the old COMPAQ with XP SP3 and of course now it will not boot.

No recent hardware changes. Only recent software change was installing Malwarebytes. After MB scan and quarantine of threats, it ran normally for a week but was never shut down until today.

Now, left alone, it would try to boot, then automatically restart repeatedly over and over, showing the black Windows XP screen for just a second. It will not boot in safe mode. It will not boot to last known good configuration. I was able to turn off the automatic restart to read the error message. On the blue screen it read:

"A problem has been detected and windows has been shut down to prevent damage to your computer.

If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps:

check for viruses on your computer.
Remove any newly installed hard drives or hard drive controllers. check your hard drive to make sure it is properly configured and terminated. Run CHKDSK/F to check for Hard Drive corruption. And then restart computer.
Technical Information:
*** STOP: 0x0000007B(0xF78A2524,0XC0000034,0X00000000,0X00000000)"

On another PC running Windows 7, I was able to download and image a .iso file with xp recovery console. After changing the boot order in the BIOS, was able to boot the COMPAQ from the disc and get into recovery console.

I am unsure how to proceed in recovery console (or otherwise) without losing ... Read more

More replies
Answer Match 95.76%

Hi,

My system has three OSes. Two Linux versions and Win XP-SP3. All of them are on different hard-disks of their own. On boot, i specify, which HD to boot from, in the boot menu from BIOS and accordingly boot from the respective Hard disk.

Most of the time, I use Win-XP. While shutting down the PC, i noticed that automatic updates were being installed. I accidentally happened to switch-off the power. Eversince, next boot, when i specify the Windows HD on boot menu, windows XP logo comes up and a blue screen appears and the system reboots to boot from Linux Disks (Default if I don't specify any disk from boot menu). I tried last working configuration, safe mode, safe mode with command prompt etc. But, same symptoms. I tried booting with WinXP CD. It tries loading the setup files and then comes to the blue screen with 0x0000007B error.

From, linux, i'm able to mount and see all the data and contents of the windows Disc.

Please help me to fix this. I need windows up and running badly. Thanks in Advance.

Please note, I do not have a floppy drive.

regds.,
Ram.

A:[SOLVED] Blue Screen Error with 0x0000007B, cannot get to command prompt, Win XP

Welcome to TSF, vrkrao :)

Part of Windows Update would include the monthly MSRT scan for viruses. If an infection was found in a System file like atapi.sys and removed by MSRT, it would lead to the 0x7B error you now see because the System file that was infected and now broken, is needed to boot Windows or that the (still infected) MBR points to a file that's been removed or modified.
https://www.microsoft.com/en-us/down...ils.aspx?id=16

The MRT.log (assuming it's written before shutdown), found in the Windows\Debug folder, should enable you to check whether the above fits your scenario, if so, it should detail which files were infected.

8 more replies
Answer Match 95.76%

Specs: HP Compaq 5100 SFF Running XP PRO SP3 With A 2.8 GHz P4 and 3 GBs of RAM.
Let me tell you what happened. I was having problems with a very, very slow CD/DVD combo drive and I looked around and around and could find only one thing that seemed like it would help and it made perfect sense. You see, I have a good computer, but it is a Small Form--not allowing me to add much to it. Anything that I have added has to be added as a slave device. Anyway, my configuration was this: My boot drive is a 80 GB SATA drive. Then, I have only one IDE Controller on the Motherboard, which has the CD/DVD drive as master and an old 40GB Hard Drive as slave. My optical drive was turtle or snail slow when viewing pictures, copying/pasting files to the HD, and anything that is data oriented. So, what I did was disconnect the slave HD drive to see if that would make it run like an optical drive was supposed to run, a little slow, but bearable. When I did this, and reconnected and rebooted, it would not boot to anything--safe mode, windows, last known configuration, hp recovery, 2 boot discs, nothing! At the opening screen, I get the opening HP screen, but it has stripes. I go into BIOS and the menus are striped. If I try to boot to Windows/Safe Mode, I get either a black screen where nothing happens, an endless pause, or a Blue Screen telling me that I have a BIOS error and they have stopped at this point to avoid any further damage. There's also a message telling me to press F7 to disable A... Read more

A:Blue Screen BIOS/ACPI Error--Striped Screen Upon Reboot: Please help!

 to the Bleeping Computer forum.
 
 
 

 
At the opening screen, I get the opening HP screen, but it has stripes. I go into BIOS and the menus are striped.
 

 
 
My assumption is one of the memory sticks got loosed from it's slot when you played with the HDD. Please remove the memory modules and use a pencil rubber to clean it's gold plated contacts.  After making sure the contacts are clean and shining, inset them to the slots. If there is more than one module, connect one at a time. Now try to boot the system.
 

8 more replies
Answer Match 94.5%

:Activity:

I recently downloaded a new firefox theme called Foxkeh Japan, but its a popular theme...so I don't think its the problem..hopefully. I don't know about these things though. I also did some torrent searching. During which I got this pop up that said I had malware and started doing a scan online, but then my Auto-Protect Poped up and I closed all the windows and pop ups and they stopped coming up.

Later I've been getting a couple of Auto-Protect Results pop up from my Symantec Antivirus (Full Version: 10.1.6.6010 Scan Engine: 71.3.0.25). So I did some updates on my SUPERAntiSpyware defintions and my Ad-Aware SE and my...Spybot...and they all found various things which I then "fixed" with those programs. I thought that be the end of it...but the Auto-Protect results been poping and I tried once more with my previous stated programs to find and eliminate the problem...and they again found some risks and then I deleted them... (sorry I did not take note of the risks). But again I got some recent Auto-Protect Pop ups (one of the risks identified was backdoorTrojanDownloader, I'm not sure if that is how it was exactly spelt but that is what I remember) and I did a Symantec update...and a scan...but the scan did not start up... and I closed the scan box, but now it won't let me start a scan saying I have a scan in progress (which I dont)...and it won't acknowledge the recent update on the virus definitions.

Recently my -

Spybot... Read more

A:Solved: Trojans...and a STOP blue screen on Reboot

16 more replies
Answer Match 93.66%

Toshiba Satellite running on windows XP
When I start the computer, it asks if for the choice of Safe Mode, w/ Networking, w/Command Prompt or Normally.
I've tried them all and if I try it normally, it won't get past the XP loading screen. It's loading and then it flashes a blue screen for a second and then restarts the computer again.

I tried pressing F8 at boot and selected 'Disable automatic restart on system failure' and this is what I get
STOP: 0x00000024 (0x00190203, 0x83306788, 0xC0000102, 0x00000000)

I even tried using this http://forums.techguy.org/6669592-post28.html to get to chkdsk
At boot, F12, chose CD/DVD, but still nothing,
I even tried disabling boot from +HDD, FDD and LAN from the bios setup menu to see if it works and this is what I got, it just keeps going on and on unless I enable boot from +HDD
Intel UNDI, PXE-2.0 (build 082)
Copyright (C) 1997-2000 Intel Corporation

For Realtek RTL8139(X)/8130/810X PCI Fast Ethernet Controller v2.13 (020326)
PXE-E61: Media test failure, check cable
PXE-M0F: Exiting PXE ROM.


That's about everything I could get.
Thanks.
 

A:Can't start XP: After XP loading screen, Blue Screen Stop error

9 more replies
Answer Match 93.66%

New to the thread.... not sure if i'm posting right, soo correct me if u want =)
Anyway.. yesterday I turned my computer on and got the screen "Sorry for the convenience blah blah blah... Start Windows Normally, Safe Mode...ect.
I chose Start Windows Normally, which did indeed start windows normally, but I wasn't sure what caused this problem in the first place, so i ignored it. I turned my computer off.

Later i turned my computer back on and was confronted by another screen, this time a Blue screen.. A Stop error, can't exactly remember the error, but said something about "memory dump'...
I eventually got avoided a problem with this screen and got into windows.. However this morning, when i turn the computer on, I was forced to use 'Last Known Good Configuration"

Whats going on? I did scans on Norton, Adaware & Spybot.

Please help!!

A:Blue Screen, Black Screen??? Stop Error Code?

Hi Kirstie, computers are great when they work huh? These stop errors and blue screens of death can have many causes. Sometimes they occur when a computer is getting older and some piece of hardware is going bad, like a memory stick for instance. Other times these errors occur after installing a new program or doing a windows update. They can be quite difficult to pin down sometimes as well. I would be glad to help you find the cause of the error if you will answer a few questions for me. By answering these questions I should be able to determine the cause and help you to correct it.

Here are some questions for you to answer that will help me. Just answer them the best you can and if you dont know an answer its ok. If you already answered anything I'm asking in your first post just skip over it.

1). What kind of computer do you have? Laptop? Desktop? Dell, HP, Ect?
2). Whats your level of experience? Novice, intermediate, expert, or dont know squat?
3). What operating system are you using? Xp Home or XP Pro?
4). What antivirus are you using? Are you using a firewall?
5) Please tell us a little about your computer. How old is your computer? What size Hard drive does it have?, processor, ram, Bios ver. Ect.
6). Do you have an Xp disk for this computer?
7). Does your computer have a floppy drive, CD drive, Ect.?
8). Do you have access to another working computer with an internet connection?
9). Did you noticed this problem occuring after installing anything recentl... Read more

9 more replies
Answer Match 92.82%

Hello,

I have a blue screen problem that i can't find a solution to!

I recently bought a new graphic card: Radeon all-in-wonder x1800xl. Installed it on a clean system (did a reformat before i installed).
The problem occurs after usually 30-60 minutes of gaming (so far with oblivion, black & white 2). The game freezes for about 30 sec and then goes into blue-screen mode.
The message is as follows:
Kernel-Data-inpage-error stop error screen
then there are a lot of numbers etc.
I have sometimes noticed a slight change in fan noise prior to freeze (speeding up)
After reebot everything's back to normal.

My system is relatively new (a year and a half or so), i have:
Windows XP pro SP2
Asus P5AD2 deluxe motherboard with integrated sound-card
Pentium 4ht, 3.4Ghz, 2GB ram.
all my drivers are up-to-date as far as i know. The ATI drivers are certainly up-to-date

I have run some fix-it-utilities diagnostics and found no error or the like.

I previously had an ATI Radeon 600 series card, on the same system. Never had a problem with HL2, Far Cry, or whatever

Any ideas?

Thanks in advance,

Zurzu
 

A:Blue screen: stop error screen when gaming

16 more replies
Answer Match 92.82%

Hello,

I have a blue screen problem that i can't find a solution to!

I have seen a similar problem posted previously on this forum. But after reading it i think this is a different problem, so, here goes:

I recently bought a new graphic card: Radeon all-in-wonder x1800xl. Installed it on a clean system (did a reformat before i installed).
The problem occurs after usually 30-60 minutes of gaming (so far with oblivion, black & white 2). The game freezes for about 30 sec and then goes into blue-screen mode.
The message is as follows:
Kernel-Data-inpage-error stop error screen
then there are a lot of numbers etc.
I have sometimes noticed a slight change in fan noise prior to freeze (speeding up)
After reebot everything's back to normal.

My system is relatively new (a year and a half or so), i have:
Windows XP pro SP2
Asus P5AD2 deluxe motherboard with integrated sound-card
Pentium 4ht, 3.4Ghz, 2GB ram.
all my drivers are up-to-date as far as i know. The ATI drivers are certainly up-to-date

I have run some fix-it-utilities diagnostics and found no error or the like.

I previously had an ATI Radeon 600 series card, on the same system. Never had a problem with HL2, Far Cry, or whatever

Any ideas?

Thanks in advance,

Zurzu
 

A:Blue screen: stop error screen when gaming

6 more replies
Answer Match 92.82%

Hello: Today I received a blue screen stop error message. I was using my AOL software at the time it occurred. This is the second time it happened; the first time was about a month ago. Last time I upgraded the driver for my video card, and I thought that had taken care of it. I don't remember for sure, but I was probably using my AOL software when it happened last time also.

The message today included this information:

Technical Information:
*** STOP: 0x0000008E (0x0000001, 0xAFCAE925, oxA714438c, 0x00000000)
*** watchdog.sys - Address AFCAE925 base at AFCAE000, DateStamp 480254ab

The message from a month ago was slightly different. It included the following information:

Technical Information:
***STOP: 0x0000008E (0xE0000001, 0xB3ED1925, 0xA379D320, 0x00000000)
***watchdog.sys - Address B3ED1925 base at B3ED1000, DateStamp 480254ab

I restarted the computer without incident.

I'd appreciate any advice; thanks.

Tech Support Guy System Info Utility version 1.0.0.1
OS Version: Microsoft Windows XP Professional, Service Pack 3, 32 bit
Processor: Intel(R) Pentium(R) 4 CPU 3.00GHz, x86 Family 15 Model 4 Stepping 3
Processor Count: 2
RAM: 2046 Mb
Graphics Card: NVIDIA GeForce 9500 GT, 1024 Mb
Hard Drives: C: Total - 472772 MB, Free - 305508 MB; F: Total - 476937 MB, Free - 432155 MB;
Motherboard: Dell Inc. , 0X8582, , ..CN7082155U50BD.
Antivirus: McAfee Anti-Virus and Anti-Spyware, Updated: Yes, On-Demand Scanner: Enabled
 

A:Solved: blue screen STOP error screen

16 more replies
Answer Match 91.56%

Hey I was hoping my last BSOD was the end of my computer woes but I guess I was wrong. Ok now I'm in abit of a tight situation as we need the computer running ASAP due to my dads stock program. Now I'll give you the rundown of what I could've done to cause this error. Firstly I was trying to connect my bluetooth device to my hp media centre computer and wasn't having too much success. So I uninstalled the device and the reinstalled it. However this time it asked me for drivers for the device but the computer couldn't find any. So the computer started checking for a solution and found one that gave a link to an update to the bluetooth software. I ran the update it failed twice so I thought maby to just reboot. I reboot and I'm greeted with missing or corrupted driver intelide.sys so I went in search of a way to fix it. The only thing I could find was this which explains how to fix the problem: LINK

I didn't have a recover disk with me as the computer came preinstalled so I created a Winre cd from here: http://neosmart.net/blog/2008/windows-vista-recovery-disc-download/

I first off attempted startup recovery but it seemed to go on endlessly with no signs of life. So I then followed the guide and backed up the copied the drivers to the drivers folder. Oddly enough the intelide driver was never there to begin with. So after it's copied it got abit further (maby half a second) but then gave me a new error, a stop error to be exact. It is S... Read more

A:Im back - Yet another bluecreen reboot loop. Stop Error 0x0000007B (0x80399BB0, ect.

9 more replies
Answer Match 89.04%

I have been given a desktop with win XP Pro. it will boot to the log in screen and i do not know or have the password for the previous user.
I have a legal copy of XP Pro and try to boot using the cd in the cd drive. it will run setup and load all the drivers and when it would normally start windows, i get the stop screen error. I have tried several boot disks with the same results. I tried Morphix (Linux) and a ERD with same results.

any thoughts?
thanks
 

A:stop screen 0x0000007b

http://www.aumha.org/a/stop.php

0x0000007B: INACCESSIBLE_BOOT_DEVICE

Windows lost access to the system partition or boot volume during the startup process. Typical causes: Installing incorrect device drivers when installing or upgrading storage adapter hardware, or a virus.
Typical causes? Installing a third party boot manager (linux) incorrect partitioning , formatting a bootable partititon but not removing the boot sector (re partitioning the drive)
Best advice; boot to bios and change boot order to cdrom , remove all other boot options and uncheck the check for other devices option.

Then you boot to your XP install CD and at the point where it asks you to click next to format and install , you select the partition which has/had windows and click the D key to Delete the partition.
Repeat for all partitions there until you have Hard disk 0 xxxxxMB unallocated space.
Then you select that and press the C key to Create new parititons.
Specify size in MB (1024MB = 1GB) or choose use all available space, follow the prompts and when finished select the first partition you created (or only one ) and click next to format it and install windows.
 

1 more replies
Answer Match 86.52%

About once a day, my computer restarts, and says it has recovered from a serious error. Have run antivirus, etc. Drivers seem to be updated. Can't find issue. Seems to happen most right after startup. Please help.
 

A:Windows XP Blue screen error - reboot

16 more replies
Answer Match 86.1%

I am getting a 0x0000007b blue screen. Are there any ways to get the operating system to boot correctly?

A:0x0000007b Blue Screen

Download BlueScreenView:
http://www.nirsoft.net/utils/blue_screen_view.html
unzip downloaded file and double click on BlueScreenView.exe to run the program.
when scanning is done, go to EDIT - Select All
Go to FILE - SAVE Selected Items, and save the report as BSOD.txt
Open BSOD.txt in Notepad, copy all of the content, and paste it into your next reply

1 more replies
Answer Match 86.1%

My laptop has a blue screen saying to check for viruses. The error code is
***STOP: 0x0000007B (0xF894B528,0xC0000034,0x00000000, 0x00000000)

Being a user and not a techie, I don't know where to start. How do I check for viruses if I can't turn the computer on?

More replies
Answer Match 86.1%

I will be working on something and this blue screen of death will pop up and then totally close windows and restart. I haven't had time to catch what exactly it says but i can give you any details from the Program Reports and Solutions tool. I have also relized that i now cannot open Outlook 2007 Adobe Photoshop. I have uninstalled/reinstalled and doesn't work. Ran Office Diagnostic Tool, no help. Tried to repair from Add/Remove Programs, says there was an error and cannot complete. There is something wrong with my Outlook.pst file and im not for sure what. I ran Scanpst.exe for Office 2007 on that file and still no help. I keeps saying that its not a Personal Files Folder. With the Photoshop, when I try to open it immidiatly says "Photoshop has stopped working" and doesn't open at all. Thanks in advance.

;***********************************************************************************************************************************************************************************
ANALYSIS: 2008-06-22 08:22:36
PROTECTIONS: 1
MALWARE: 12
SUSPECTS: 12
;***********************************************************************************************************************************************************************************
PROTECTIONS
Description Version Active Updated
;============================================================================================================================... Read more

A:Blue Screen that shows error and causes auto shutdown

Hi,

Welcome to Tech Support Forum.

uTorrent and Limewire are installed on your computer. While both are clean P2P programs, there's no guarantee that the files downloaded are. Please refrain from using them while cleaning your computer to prevent getting more infections.

A list of clean and infected P2P programs can be found at Malware Removal and Spyware Info.

The risks of using a P2P program are stated in this Sourceforge website and Information Week article.
_____________________

Please download Combofix from one of these links and save it to your desktop:

Bleeping Computer
Forospyware
Geeks to Go

Right click on ComboFix.exe and select Rename.

Copy and paste in Combo-Fix.exe and press Enter.

Right click on Combo-Fix.exe and select Run As Administrator. You will receive an UAC prompt; please allow it.

Follow the prompts. When done, a log will be produced. Please post that log and a new HijackThis log in your next reply.

Do not mouse click on Combofix while it is running. That may cause it to stall.

In your next reply, please post:
Combofix log (C:\Combofix.txt)
A new HijackThis log

19 more replies
Answer Match 85.68%

I am getting a stop error message 0x000000F4 I can't even get on Windows. I have a Dell Inspron 1525 with Windows Vista. I can't use safe mode or any of the modes. The hardware diagnostics check was clean. I tried start up repair from the OS disc with nothing. What can I do here
 

A:Stop Error Blue screen

How strange....I worked on a laptop last night with the same issue. In fact, it was the same exact laptop.
When I did the Dell Diagnostics tests, it came back with a failed hard drive. But yours passed?
One thing I did read about that error message that I did not try was checking the CMOS battery.
Try popping out the battery, wait 30-60 seconds, and putting it back in.
Otherwise, I would still suspect a failing hard drive.
 

2 more replies
Answer Match 85.68%

I keep gettting a blue screen error when i open internet explorer or firefox.

The stop error is

Problem detected and windows has been shut sown to prevent damage to the computer

RQL_NOT_LESS_OR_EQUAL

Stop: 0x0000000A(0x00000002,0x0000000a,0x806E4A16)

The computer is a Dell Inspiron, i have tried removing software from the machine but i keeps happening.

Can anyone help me out, you help is greatly appreciated.

Thanks

Chris
 

A:Stop Error - blue screen

Typically, this error occurs when a driver uses an incorrect memory address. Other possible causes of this error are an incompatible device driver, a general hardware problem, and incompatible software.

http://support.microsoft.com/default.aspx?scid=kb;en-us;Q314063

Start by reinstalling the Video and motherboard drivers?
 

2 more replies
Answer Match 85.68%

STOP:0x0000007E(0xc0000005,0xFA9A73922,0xF9E49008,0xF9E48D08)
viadsk.sys-address F9A73922 Base at F9A72000, Datestamp 38eb04c7
 

A:Can someone look at this STOP Blue Screen Error?

16 more replies
Answer Match 85.68%

0x000008E 0x000001D,0xEB17166B,0xF1C51b28,0x00000000

address EB171568B base at EB1600F datestamp 448cd31


Eeeep! What does this mean and how do I fix it?!

A:Blue screen STOP error

when you got the blue screen was there any other info? usually near the bottom left of the screen there is a file name.

2 more replies
Answer Match 85.68%

I've got a case of the blues , I know this is isn't new news to anyone but the blue screen is not going away ,. I'm running a Compaq Armada E500 laptop with windows 2000. I've tried to clear the blue screen , F8 ,F12, i've tried to start up in safe mode and everything listed in the list of examples but nothing works. I switched hard drives from my other Laptop and it stared up no problem . how can i reboot the hard drive if i can't run in safe mode?

Any help with this matter would be great!
 

More replies
Answer Match 85.68%

I was referred here by a helper in Spybot Search & Destroy. I ran my logs and posted for him, he recommends that someone here at this forum take a look at my logs to decipher if my problems is caused by software vs. hardware. I waited 4 days for his response. Now my computer is really slow. I've had to run in safe mode a few times.

Can someone assist me, thanks in advance. This is my first experience with a blue screen stop error.

Here is the error code:
BCCode:9c BCP1: 00000000 BCP2: 8054E5F0 BCP3: A2000000 BCP4: 84010400 OSVer:5_1_2600 SP:3_0 Product:256_1

Here is the logs on 1/22/2011.

DS (Ver_10-12-12.02) - NTFSx86
Run by Iovo & Christina at 18:57:55.10 on Sat 01/22/2011
Internet Explorer: 8.0.6001.18702
Microsoft Windows XP Professional 5.1.2600.3.1252.1.1033.18.894.294 [GMT -10:00]

FW: ZoneAlarm Firewall *Enabled*

============== Running Processes ===============

C:\WINDOWS\system32\Ati2evxx.exe
C:\WINDOWS\system32\svchost -k DcomLaunch
svchost.exe
C:\WINDOWS\System32\svchost.exe -k netsvcs
svchost.exe
svchost.exe
C:\WINDOWS\system32\ZoneLabs\vsmon.exe
C:\WINDOWS\system32\spoolsv.exe
svchost.exe
C:\WINDOWS\system32\agrsmsvc.exe
C:\Program Files\Common Files\Apple\Mobile Device Support\bin\AppleMobileDeviceService.exe
C:\Program Files\Bonjour\mDNSResponder.exe
C:\Program Files\Symantec_Client_Security\Symantec AntiVirus\DefWatch.exe
C:\WINDOWS\eHome\ehRecvr.exe
C:\WINDOWS\eHome\ehSched.exe
C:\Program Files\Java\jre6\bin\jqs.exe
C:\Program Files\Goog... Read more

More replies
Answer Match 85.68%

I had been using Picasa version 2.7 to edit and upload my photos to Picasa online. All was fine until I downloaded version 3.0 Beta. I now get a blue screen stop error. Uninstalling 3.0 and reinstalling 2.7 does not correct the problem. I then did a search of the word 'Picasa' on my computer and found about 30 files which were not removed by the uninstall so I manually deleted these files. I then reinstalled 2.7 again but no change. I did a virus and spyware scan and no help there either. The blue screen appears when Picasa does its scan of the computer for pictures and videos - at the end. The error message reads: Stop: 0x0000008E (0xC0000005, 0xA5ABCB2C, 0x00000000)

nv4_disp.dll - Address BF077755 base at BF012000, DateStamp 482dff70

I did the Dell self test diagnostics which turned up nothing.

Any help would be appreciated.

A:Blue Screen Stop Error

Try updating your video card drivers from HERE. It looks like the install has caused some corruption for you.

2 more replies
Answer Match 85.68%

I am new to this forum and am not a computer geek, although I understand the basics of computing and can usually figure out a problem, sometimes needing help....as now.

I have an IBM R51 Think Pad with Windows XP.
My problem is that I loaded an HP Photosmart disk for a digital camera in my disk drive. The software did not download and I was not able to open my disk drive to remove the software. I managed to remove the entire drive from my laptop but was still not successful in removing the disk. When I booted my laptop (several attempts) a blue screen appeared telling me that I had a "stop error" which could be due to a hardware/software change. I was instructed to choose "last known good configuration (most recent settings that worked) but that only takes me to a blue screen stating: Technical information: **** STOP: 0x00000007f (0x00000008, 0x80042000, 0x00000000, ox00000000). I reinserted the disk drive in my laptop and after several attempts to log on a balloon informed me that Norton had detected a "backdoor" virus. I cannot go into safe mode. I can only go back and forth between the F8 window and the blue screen.

The blue screen also suggested: disable or remove any hardware or drivers; remove any newly installed software; restart computer in safe mode; run a system diagnostic utility (I do not have).

Can someone please help me get this straightened out or am I stuck with a fried laptop???? Thanks in advance for any assis... Read more

A:Stop Error Screen (Blue)

I don't quite understand what you were trying to download after loading the hp photosmart disk into your drive ! did the CD load the digital camera software or not? all CD/DVD drives have a pin hole on the face of the drive door cover that you can use to put a paper clip or needle into to push and manual eject the CD or DVD out ...so you can remove the disk. try that first.....then reboot to see if that makes a difference. also Do you have a XP CD to try to attempt a XP operating system repair...? a repair of your operating system will leave all your precious data files intact. or hopefully you are savvy enuf to have used an external harddrive to back them up via a usb port. post back with results and answers....

18 more replies
Answer Match 85.68%

I get this almost everyday, I even restored the laptop to how it was out of box and it keeps crashing... here is the error.

MULTIPLE_COMPLETE_REQUESTS

***STOP: 0x00000044
(0x862df368,0x00000D60, 0x00000000,0x00000000)
 

A:Blue Screen Stop Error...

10 more replies
Answer Match 85.68%

I kept getting a stop: error message everytime I tried to reinstall windows on this computer I am working on. I figured it was just a hard drive issue, so I replaced it and now I am running into the same type of error. It is a blue screen with this information:

STOP: 0x0000007E (0xC0000005, 0xF7577D44, 0xF7ADCC5C, 0xF7ADC92C)
Ntsf.sys - Address F7577D44 base at F7572000, DateStamp 3d6de5c1

then it runs a physical memory dump, any ideas?

A:Blue Screen W/ Stop: Error

I notice you have an HJT log posted. Is this the same computer? If so, please follow only the instructions given to you by the HJT team member who takes your log.

Thanks,
rigel

4 more replies
Answer Match 85.68%

I've been getting a Blue screen lately, it rarely repeats on reboot, but keeps coming back periodically.

Stop: 0x0000007E (0xC000001D, 0x806ECABD, 0xBA4C2DC0, 0xBA4C2ABC)

Nothing after that. In my experience I have seen bad Memory cause blue screens, so I removed one stick and still got the error, I then switched to my other stick and thought I had found it because It went a couple of days, then today it happened again. This system has been running flawlessly since I built it, about a year and a half ago. No recent hardware or software changes, I was about to install Windows 7, but hadn't gotten around to it yet.

I do have 2 slave Hard drives, I am currently unplugging them one at a time to see if it continues.

Does anyone have any idea what these numbers in the error mean? Would appreciate any help. My system is in my signature.

Thanks,
Rick

A:Help with Blue Screen Stop Error

Post a zipped copy of your Minidump files found in your Windows folder.

12 more replies
Answer Match 85.68%

hello all....

my boss at work asked me to take his home pc home with me and put WIndows XP Pro on it for him....he was previously running Win2K. After running the setup and doing the install, on reboot, when trying to log on, i get a stop error blue screen. The only technical info at the bottom is this :

STOP: 0x0000008E (0XC0000005,0X804F2906,0XF533176C,0X00000000)
Beginning dump of physical memory
Dumping physical memory to disk: xx

where xx is a slow counting upwards number, starting at 1, until eventually it resets itself and starts the problem over again.

I am able to boot into safe mode.

The computer in question is a Gateway with a Pentium 2 348mhz, with 384mb ram.

if anyone can help, PLEASE DO! i do not want to return my bosses computer to him inoperable!
 

More replies
Answer Match 85.68%

I have a Dell Dimension 2400 computer and I am running Windows XP. I've been getting a stop error message that reads:

A problem had been detected and windows had been shut down to prevent damage to your computer.
DRIVER_IRQL_NOT_LESS_OR_EQUAL
If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps: Check to make sure any new hardware or software is properly installed. If this is a new installation, ask your hardware or software manufacturer for any windows updates you might need. If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory option such as caching or shadowing. If you need to use safe mode to remove or disable components restart your computer, press F8 to select advanced start up options, and then select safe mode.
Tech info: STOP: 0X0000DI (OXF749A508).....Blah, blah, blah...
Beginning dump of physical memory.
Physical memory dump complete.
Contact system administrator or tech support.

I've tried to research this and it says that I should uninstall the incompatible hardware. How do I know which item is causing the problem? Is there some kind of test I can perform? I tried wiping the computer, but it still happens. Please help!!!
 

A:Stop Error Blue Screen

Look in C:\Windows\Minidump for crash dump files with a DMP extension. ZIP some recent ones (5-6) and post here as a ZIP or RAR file. Debug analysis of the files usually points to the problem.
 

2 more replies
Answer Match 85.68%

Hello,

This morning, I tried turning on my desktop on in the living room, and was greeted with a black screen. This screen told me that the computer was shut down improperly, and that I had the choice to run in safe mode, safe mode with command prompt, safe mode with networking, restart to last good known configuration, and start windows normally.

I've tried to use every single option, but all of them load the "Windows XP Loading" screen for a max of 4 seconds, and then goes to a blue screen. The blue screen says:

"A problem has been detected and Windows has been shut down to prevent damage to your computer.

If this is the first time you've seen this Stop error screen, restart your computer. I this screen appears again, follow these steps:

Disable or uninstall any anti-virus, disk defragmentation or back up utilities. Check your hard drive configuration, and check for any updated drivers. Run CHKDSK /F to check for hard drive corruption, and then restart your computer.

Technical informatoin:

***STOP: 0x00000024 (0X001902FE, 0XF78E63DC, 0XF78E60D8, 0X8A5B9805)"

Of course thinking the worst at first, I call my roomate asking him what the computer was doing this morning, and he told me it was acting weird. Long story short, I got him to admit he was looking at things he shouldn't have been on my computer, and somehow got a virus on it. He said it installed a windows security program, and icons with porn in their names showed up. He s... Read more

A:Blue Screen STOP error

You may need to do a "clean install" or "full recovery" so you should review your options for that before proceeding. Most Dells have a "recovery partition" for that. (I think the F11 boot menu brings that up)

-----------------------

There is one option here that I normally only recommend for resourceful and experienced users, however if you have no choice but a "clean install" it is worth a try.

Reinstalls (overinstalls) by the way, will not remove viral components.

USING THE RECOVERY CONSOLE TO ACCESS SYSTEM RESTORE
If you do not have an XP CD download rc.iso from Elvandil's post here: http://forums.techguy.org/windows-nt-2000-xp/561576-mom-exe.html#post4622868
Burn the .iso file to CD. With Nero or Roxio you should only need to "open" the file and it will start the burner's ISO burning program.

DeepBurner can also be used to burn ISO files, I recommend the “portable” version:

http://www.deepburner.com/?r=download
Once that is done, you need to boot with either that or the XP installation CD to the Recovery Console. You may need to ensure that the CD drive is the first boot drive in the BIOS setup if it just boots to the same screen. Setup is accessed by looking for the key to press on the first data you see on the screen -- often F2

Directions are given here:

http://attachments.techguy.org/attachment.php?attachmentid=62075

There are several things to note about this operation.

1 ... Read more

1 more replies
Answer Match 85.68%

hello
This morning I was working on my computer first it started working slowly then I tried using my web browser (fire fox) came up error not enough resources are available. So restarted my computer then the blue screen hit me I tried safe mode. Tried all options from boot menu didn?t work so can anyone please help me

im doing now memtest86

More replies
Answer Match 85.68%

Hello, I have turned on my PC and flit has brought me to a blhe screen with the following error
"A problem has been detected and windows has been shut down to prevent damage to yoyr computer.
If this the first time you've seen thjs stop erroer screen, restart your computer. If this screen appears again, follow these steps:
Disable or uninstall any anti virus, disk de fragmentation or backup utilities. Check your hard disk configuration, and checkfor any uupdated drivers. Run CHDSK /f to check for hard drive ccorruption, and then restart tlyour computer.

Technical support:
*** STOP: 0x00000024 (0x00190203, 0x8aad1c78, 0xc0000102, 0x00000000)

I need help and dont know what to do, I dont have the sindows xp instalation disc and cant go past this screen
Please help my only working pc

A:Blue screen STOP error help

Sorry, but this is a Windows 7 forum.

2 more replies
Answer Match 85.68%

I hope someone can help I have been looking ever where for an answer to this. Once in a while I get a BSOD it says
IRQL_NOT_LESS_OR_EQUAL
0X0000000A (0X00000000, 0X000000FF, 0X000000, 0X806E2EA0)

I am not to sure what to do about this. Also ever time I restart or shut down my computer just after I click either one I get
Stop Error: 0x000000C4 (0x00000060, 0x00000064, 0x00000000, 0x00000001)

I hope this is all the information that is needed. Thank you for any help.
 

A:Blue Screen Stop Error

16 more replies
Answer Match 85.68%

I've been getting this Blue Screen that tells me to re-start my computer and it's frustrating me because I'm not sure why it keeps happening.

The blue screen says:

STOP: 0x0000008E (0xC0000005, 0x8054B0BA, 0xB2AC55EC, 0x00000000)

I have no clue what it means or why it's happening. It suggests I disable BIOS updates and says that a physical memory dump is occurring. I haven't downloading new drivers or anything (which is the suggestion Windows makes when I re-start the computer). I also have more then enough disk space so that shouldn't be an issue. Can anyone help?

I also may have part of the above stop error message wrong because I scribble it on a post-it. I can get a more detailed one if that helps. Thanks in advance because any help would be appreciated!!!!
 

A:Blue Screen - Stop Error

13 more replies
Answer Match 85.68%

First of all Hi.

I am not very computer savvy so any help is greatly apreciated.

I am getting a blue screen error on the start up of my laptop. This first occured while the laptop was running.
The error # is 0x0000007E (0xC0000005, 0x8A0C894c, 0xBACF78B4, OxBACF75B0). There is no other information on the blue screen.

I can start the computer in Safe mode, but not Safe Mode with networking.

The Laptop is a Dell with Intel(R) Core(TM) 2 CPU T5200 @1.60GHz
Running Windows XP professional, with service pack 3.

Will be checking thread repeatedly if you need any more information.

A:Blue Screen / STOP error

http://support.microsoft.com/kb/330182

Visiting the above link, a popup should appear download it and run the fix, if it doesnt work try following the steps on the page.

If you cant access the internet on your laptop simply download it elsewhere a.k.a a pc or something and use a cd or usb stick to transfer it to your laptop and use it in safe mode.

5 more replies
Answer Match 85.68%

I tried to boot up my computer a couple of days ago and had a stop error. I have tried to do a recovery with the disks that came with my laptop, but with no success. Of course my laptop didn't come with the XP installation CD's so I can't even start a repair on the PC.

I tried to contact HP, but they were unable to help me. I hope someone here can help me more than HP was able to.

Thanks
 

A:XP Blue Screen Stop Error

7 more replies
Answer Match 85.68%

All of a sudden I've been getting this blue screen every so often the last few weeks. It's a STOP: 0x0000009c(0x00000002, 0x8054D570, 0xF6002000, 0x0000017)"MACHINE_CHECK_EXCEPTION". I can go an extended amount of time and have nothing happen and then all of a sudden it can come out of nowhere. I believe it has something to do with hardware, but I have no clue where to begin.
 

A:Blue Screen Stop Error

Start > Run > eventvwr.msc > copy and paste some of the recent errors

also ...

navigate to C:\windows\minidump
Zip some of the recent minidumps and attach them here
 

1 more replies
Answer Match 85.68%

I posted this thread before and was being helped by someone, but they didn't return after the initial day. Maybe I wasn't clear but anytime I try to boot back up, it goes straight into the blue screen. I am able to start in safe mode. They asked me to boot back up in safe mode and go to run and type in "SFC.EXE /SCANNOW". I did this but when I hit run or enter the run screen went away and nothing happened. So here is my original question.
I run windows xp. I was trying to download pictures on my computer from a disk that I made at a local drug store kodak kiosk when this started. I also found out a couple of days ago that a "friend" was surfing some really questionable sites. The computer was running fine until i put in this disk with pictures. I saved a few to the computer and then it blacked out and a blue screen came up with the following message. Also I tried turning it off and on a few times and it gets to the desktop and as soon as I try to go to the web or acess anything on the start menu, it goes right back to this blue page.

A problem has been detected and windows has been shut down to prevent damage to your computer.
If this is the first time you have seen this stop error screen, restart your computer. If this screen apperars again, follow these steps
Check to be sure you have adequate disk space. If a drever is identified in the stop message, disable the driver or check with the manufacuter for driver updates. Try changing video ad... Read more

A:Blue Stop Error Screen

http://support.microsoft.com/kb/330182

28 more replies
Answer Match 85.68%

I have gotten this screen a few times before but thought nothing of it bcz I could get back online after shutting down. Its gotten to a point where its bothering me now. It always states the same thing... There was an error with your new hardware, we need to shutdown, sorry for the inconvenience, etc etc... then it gives me a few error numbers... this first error number was the main one... then the others... came up exactly like it is here
0x000000D1 (0xF8F32CB8, 0x00000002, 0x00000000, 0xF8EE0CE0) Please help!
Ice
 

A:Blue Stop Error Screen!!! ?????

11 more replies
Answer Match 85.68%

Hi, been having trouble lately with wife's computer rebooting off and on by itself during web browsing or other things. Here's the latest that came up. I set it to not reboot when errors occurred, but this blue screen came up and wondered if any of you know what it is. One thing i done was to go to nVidia site and upgrade my video driver. It's a 32M nVidia GEForce MXDOR. It was rebooting on it's own before i upgraded too. Anyways here's error:

***Stop:0x0000008E(0x0000005,0xF838CB3B,0x4BD7720,0x00000000)

***NDIS>SYS-ADDressF838CB3B baeat F838c000,DateStamp 2367dc561

Beginning dump of physical memory
Physical memory dump complete

Contact your system administrator or tech support group for further assistance.

Thanks in advance for any help
Its win xp home
 

A:Stop Error Blue Screen

16 more replies
Answer Match 85.68%

Hey everyone!

I need some help!

Here's the situation.

I have 2 identical dell laptops (exact same hardware profile and software deployment)

For Purposes of illustration I'll refer to them as A and B.


Laptop A came to my desk this morning with a stop error "PAGE_FAULT_IN_NON_PAGED_AREA" pretty typical BSOD.

So I pull the hard drive and put it in laptop B it works flawlessly which rules out the drive/software being the problem.

I then take the hard drive that just came out of laptop B and install it in laptop A.

Now both are working flawlessly which rules out the hardware in laptop A.

Thinking what ever the problem is may have worked itself out I put the drives back in their respective laptops and again got the stop error in laptop A.

As a side note both laptops boot far enough to get to the login in screen, it's when you log into the domain after it authenticates the users credentials that the page fault error occurs.

Any advanced knowledge in this matter would be appreciated.

Thank you!

A:Blue Screen Stop Error

Questions..

What model laptops are they? Also, which OS are they running?

And..does the stop error occur during every boot? Or is it just most of the time?

When you installed Laptop A's Hard-Drive into Laptop B, did the chkdsk utility launch at start-up?

3 more replies
Answer Match 85.68%

I've been trolling through this website and many others to find the exact nature of my problem but I haven't come across any. From what I gather my problem can fall under many many different hardware/software problems but I am just going to go ahead and ask your advice anyway.

When I blue screen I get the following message

STOP: 0x0000009C (0x0000000000000003, 0xFFFFF880026D4B30, 0x00000000B6200000, 0x000000000002010A)

Now I have consulted with family members who are more switched on when it comes to the finer details of computing and they suggest that it is faulty RAM. Which I am inclined to believe as the blue screen occurs when I am running RAM intensive applications (Java based game (Minecraft)), it usually happens around the 65% mark. I've also taken Google's own advice of updating all system drivers. Everything is up to date.

Looking forward to your take on this.


Bucky
 

A:Stop error - blue screen

So check the memory using Memtest86
 

4 more replies
Answer Match 85.68%

Hello,
Every 1-3 weeks I seem to be getting the same error, my screen flashes into a blue screen error and shuts down my computer, this happens out of the blue and is very unpredictable. I have written down the full error displayed, it says:

A problem has been detected and windows has been shut down to prevent damage
to your computer.

If this is the first time you've seen this stop error screen, restart your computer.
If this screen appears again follow these steps:

check to be sure you have adequate disk space, if a driver is identified in the stop
message, disable the driver or check with the manufacterer for driver updates, try
changing video adapters.

Check your hardware vendor for any BIOS updates, disable BIOS memory options
such as caching or shadowing, if you need to use safe mode to remove or disable
components restart your computer. press F8 to select advanced startup options,
then select safe mode.

Technical information:

*** STOP: 0x0000008E (0xC0000005, 0x9D1243A0, 0xD4DBEAE0, 0x00000000)

* Ti win32k.sys - Address 9D1243A0 base at 9D090000, Date stamp 4f2aa8Bc

Collecting date for crash dump
initialising disk for crash dump
Beginning dump of physical memory
Dumping physical memory to disk: 100
Physical dump complete

Contact your system admin or technical support group for further assistance.

If someone could please help me with this problem i would be very greatful!
 

A:Blue Stop Error Screen

that can be caused by a virus
follow advice here and post the logs those programs make

once I see the logs I can determine if it needs moving to malware or whether it is more likely to be other software/hardware causing it
 

1 more replies
Answer Match 85.68%

Hi,
This is for a gateway MX6448 Win XP. Tapped mouse when computer went into hibernate mode, then computer shut down and restarted with a blank screen then repeated to shut down and restart over and over. Went into bios F2 did nothing but exit and save. Restarted and it did the same thing. Went into F8 could not reboot into safe mode (did same thing) went into F10 chose to not automatically restart on system failure. Now reboots to blue screen with stop error: C0000221 bad image check sum. bad image gdi32.d77 is possibly corrupt the header does not match the computer check sum.

Please advise

Thank You so much
 

A:blue screen and stop error Please help!

16 more replies
Answer Match 85.68%

I need help with an error I've been getting every so often. I spent the last few weeks dealing with HJT logs and combofix trying to find the problem. The topic has been closed, because my registry is clean and my virus software isn't finding any viruses. I've been told to turn off my automatic restart so I can get the information from the blue screen. I've done that and it is a (I think) Stop Error. The top of the page says a problem has been detected and so on. It has KERNEL_DATA_INPAGE_ERROR. It says some other generic problem solving steps that don't really work like checking for installation of any new hardware and software. It talks about disabling some of the BIOS memory options such as caching and shadowing. I have not done that only because I don't know what it will do. I know how to do it, just not what it will do or the purpose. Then it says Technical Information:
*** STOP: 0x0000007A (0xc03dd7ac, 0xc000000e, 0xf75eb130, 0x137c5860)
*** atapi.sys - Address F75eb130 base at f75da000, DateStamp 41107b4d

Beginning dump of physical memory
Physical memory dump complete
Contact your system administrator or technical support groupfor further assistance.

I apologize for how long this is but I wanted to get all the important inforation down incase any of it was important. Any help on how to fix this problem would be greatly appreciated. Thank you very much.

A:Stop Error/blue Screen

Try this: http://www.annoyances.org/exec/forum/winxp/1106266732

1 more replies
Answer Match 85.68%

http://wer.microsoft.com/responses/....3.0?SGD=f7d24a35-17a4-4ab1-848d-ee6651bfacea

I get this, almost everytime i turn on my pc... that is, when I CAN turn the computer on.

Everytime I start up my computer, i am faced with the 'start windows normally', 'last known good configeration' and 'safe mode' options... *when i chose safe mode the computer is immediately restarted, and the same when I chose last good known configeration.
Sometimes I must restart my pc like 10-15 times, just to get it to the windows loading screen, where I finally see my homescreen, for about 30 seconds that it before it restarts.

Today I am using the same computer, it has so far restarted twice in the last hour, but i know when it restarts I may not be able to turn it on again =\

Anyway... sO i repeatedly chose F8 when my pc started up, and chose the setting 'Disable Automatic Restart on System Failure', and I was faced with a blue error screen

'The BIOS in this system is not fully APCI compiant. Please contact you system vendor or visit http://www.hardware-update.com' (this website didn't seem to work for me.
'You vender is not fully ACPI compliant'

In the past month or two, i have also been faced with other blue error screens

1). 'Win32k.sys - Address BF8937D8 base, BF00000, Datestamp 4cc6d692.

STOP: 0x0000008e (0xc0000005, 0x80637625, 0xb8217b08, 0x00000000)'

2). IRQL_NOT_LESS_OR_EQUAL

3). PAGE_FAULT_IN_NONPAGED_AREA
... Read more

More replies
Answer Match 85.68%

I was removing SP3 due to a compapability issue when my laptop crashed. When it retarted I got the following...
I had a "Skipping Auto Check" - Fatal Error Stop: C000021a
The session manager initilazation system process terminated unexpectedly
with a status of 0xc000003a (0x00000000 0x00000000)
the system has shut down

I am running xp home and have tried retstarting in "safe", "Repair", "last good config" etc none work. Tried loading XP disk and set up but now says it cant find any hard drives!

Please help!!!!!!!
 

More replies
Answer Match 85.68%

Computer has been running fine I believe an update happened because when I got home it was restarted and on the login screen which I would never leave it at and when it updates automatically that it usually the screen I see BUT I am not 100% sure that this happened. I hadn't done anything new to it for weeks either.

So, I come home today and when I turn on the beast it takes me to the 'System Recovery Options'

Which allows me to
- Startup Repair
- System Restore
- System Image Recovery
- Windows Memory Diagnostic
- Command Prompt

I tried all the options and I get this for an answer:
- Startup Repair
Startup Repair cannot repair this computer automatically
- System Restore
To use system restore, you must specify which windows installation to restore.

Restart this computer, select and operating system, and then select system restore
- System image recover
An internal error occured. The following information might helpyou resolve youre error:
The system cannot find the file specified. (0x80070002)

-
Windows cannot check for memory problems
an error is preventing Windowsfrom checking for memory problems during startup. To run the Windows Memory Diagnosis manually, book the computer from the Windows installition disc, and then slelect windows diagnostic from the Windows boot menu.

-----------------------------------

I have the windows disc i set bios to boot for cd drive but it doesn't seem to work.

The only options upon boot are
1. Launc... Read more

A:Blue screen and reboot on start up, Error 0x80070002

I was able to video my screen to see the bluescreen error message and it says 'UNMOUNTABLE_BOOT_VOLUME' hope this helps.

1 more replies
Answer Match 85.68%

Upon reboot or startup I receive an error message:
Checking file system on C:
Type of file system is NTFS
volume is dirty
CHKDSK is verifying file (stage 1 or 2)
file verification is completed.
CHKDSK is verifying indexes (stage 2 or 3)
percentage completed
CHKDSK is verifying security descriptors (stage 3 of 3)
percentage completed

I then get an opportunity to send an error message to microsoft (I wrote down the error signature if that's helpful)

This has occurred the last few times I reboot, I must confess that I have been leaving my computer on 24/7 for the past couple of weeks, since first receiving this error message. But today the silly thing required a reboot because I got the blue screen of death error message (which I did not write down) in the middle of surfing the web.

Any idea what's causing this? How can it be fixed? Any help will be appreciated. By the way, I know a little day to day computer stuff but can be walked through most anything.....just don't know a lot of technical terms and such.
Thanks!

A:Blue Screen upon startup or reboot with error message

Hello glassflute

We really need to know the blue screen error message in order to help
Please post the message such as
STOP 0x00000000A IRQL NOT LESS OR EQUAL
and any drivers named ( *****.sys)

In the meantime, back up all your files/data and run check disk yourself with the repair switch

Start/Run and type in
cmd
OK

At the prompt type
Chkdsk C: /f /r (there is a space before both of the /)
Assuming Windows is installed on "C"
Enter

Reboot and chkdsk will run again and try to repair any errors. If it finds errors this can take quite a long time.

.

4 more replies
Answer Match 85.68%

Using Windows XP Professional 2002 SP 2

I made the mistake of letting someone else use my PC while I wasn't around to make sure they weren't going to do something unintelligent. Turns out, they clicked a link which forced Adobe Reader to open and install some kind of trojan. I instantly started getting random and fake "anti spyware" popups telling me I needed to buy such and such. I immediately ran malwarebytes, which found about 9 infected files, and deleted them. The popups stopped, but as soon as I rebooted I received a message, after the Windows boot up screen, but before the logon screen, that said wmiprvse.exe was not found, skipping Autocheck. I thought it was odd, but didn't think too much about it.

I noticed after that reboot that instead of the usual 4-5 svchost.exe 's that task manager picks up, I've been seeing between 7 and 8, with one or two running at a particularly high memory usage level. I thought that was odd too, but I wasn't sure what to make of it. Fast forward maybe 6 hours of normal usage, I got a sudden blue error screen for about 2 seconds, I didn't have any time to read what it said, but it forced my computer to reboot. This time, again after Windows boot up, but before the logon screen, I got an error message, but this time it said msln.exe was not found, skipping Autocheck. I've never seen either of these error messages before the virus so it's starting to get worrisome. I own up to date Norton Antiv... Read more

A:Blue error screen + random forced reboot

Worth reading, http://www.istorya.net/forums/software-and...-startup-2.htmlI would think it worth a trip to the Am I Infested forum; I will suggest that this thread be moved there.Louis

4 more replies
Answer Match 85.26%

The notebook boots, and when its showing the windows logo, a blue screen appears (Code 0x0000007B). As suggested in other questions in this forum, I tried changing the the AHCI setting to IDE but the option is not available in the BIOS since its an M.2 SSD. Any solutions?

A:Blue Screen Code 0x0000007B

Hi TobyWe have exactly the same problem. Did you find a solution yet?Thanks for help!

2 more replies
Answer Match 85.26%

Well I decided to post a new thread because no one has had the same issue as I did. I have a compaq presario sr1300nx which had a dead harddrive. I bought a new external Hardrive (Seagate 160gb). The problem is I can't reinstall window xp because it isn't able to boot from Usb. I been trying nlite but it doesn't work. I have a bios named pheonix vers. 6 which isn't helping. Need help! wasted a bunch of cds on trying to streamline new drivers into the cd already.
 

A:Blue Screen 0x0000007b(window xp)

why not just replace the harddrive in the compaq ?
 

2 more replies
Answer Match 85.26%

Thanks very much in advance for your help!

Here is our problem: when trying to start Windows XP Home Edition, the following error message appears on a dreaded blue screen:
A problem has been detected and Windows has been shut down to prevent damage to your computer. If this is the first time you've seen this screen, restart your computer. If this screen appears again, follow these steps: Check for viruses on your computer. Remove any newly installed hard drives or hard drive controllers. Check your hard drive to make sure it is properly configured and terminated. Run CHKDSK/F to check for hard drive corruption, and then restart your computer. Technical information: ***STOP: 0x0000007B (0xF91CF528, 0xC0000034, 0x00000000)

1. I restarted the computer. The Windows screen did not appear. The blue screen/error message appeared.
2. I attempted to restart in Safe Mode. The Windows screen did not appear. The blue screen/error message appeared.
3. I attempted to disable automatic reboot on system failure. The Windows screen appeared briefly, then the blue screen/error message appeared.
4. I cannot check for viruses, as I cannot get past the blue screen/error message.
5. We have not installed any new hard drives or hard drive controllers.
6. I do not know how to check the hard drive to make sure it is properly configured.
7. I do not know how to run CHKDSK/F to check for hard drive corruption.
8. I attempted to start in Safe Mode with Command Prompt. The blue screen/error m... Read more

A:Blue Screen Error Message On Startup - Auto Shutdown

<<I do not know how to check the hard drive to make sure it is properly configured.>>If it's properly connected, reflected correctly in the BIOS, and partitioned/formatted...it's properly configured, IMO. Whether it has problems is a different story.System manufacturer and model (e.g., eMachines T1357)?Do you have recovery/restore CDs? Do you have a MS Genuine XP install CD?Louis

1 more replies
Answer Match 84.84%

i have been having a reocurring issue trying to edit some video and been getting stop errors at the same point along the process. i have used a debugger to obtain a description of the minidump that occurs with the stop error and have copied it below. i have also been reading about disabling caching and shadowing features which are mentioned in the stop error desctiption screen.

cpu information:

dell dimension 8300
windows xp professional 2002 (32-bit)
service pack 3
pentium 4 2.6 GHz
2.59 GHz, 3.25 GB of RAM
NVIDIA GeForce 6200 vid card

this is my first post and any information would really really be appreciated.
* * * *
Microsoft ® Windows Debugger Version 6.10.0003.233 X86
Copyright © Microsoft Corporation. All rights reserved.
Loading Dump File [C:\WINDOWS\Minidump\Mini122908-04.dmp]
Mini Kernel Dump File: Only registers and stack trace are available

Symbol search path is: SRV*c:\symbols*http://msdl.microsoft.com/download/symbols
Executable search path is:
Windows XP Kernel Version 2600 (Service Pack 3) MP (2 procs) Free x86 compatible
Product: WinNt, suite: TerminalServer SingleUserTS
Built by: 2600.xpsp_sp3_gdr.080814-1236
Machine Name:
Kernel base = 0x804d7000 PsLoadedModuleList = 0x805634c0
Debug session time: Mon Dec 29 22:56:43.446 2008 (GMT-8)
System Uptime: 0 days 0:03:26.071
Loading Kernel Symbols
...............................................................
............................................................. Read more

A:help diagnosing blue screen stop error

My guess would be that it's your VideoWave program...possible corruption/damage in either the program itself or the drivers it employs.http://kb.roxio.com/content/kb/General%20I...mation/000071GNI would suggest uninstalling/reinstalling the program and updating same...along with a defrag of the partitions which you are using for storage of outputs/inputs you edit.Louis

4 more replies
Answer Match 84.84%

Hey there,

Sorry if I'm repeating the subject here but I got this recurring problem every 4 to 5 hours and can't seem to solve it.

I'd appreciate any help here.

I'm pasting the error from Event Viewer, please help me!

Event Type: Error
Event Source: System Error
Event Category: (102)
Event ID: 1003
Date: 23-02-2006
Time: 20:16:35
User: N/A
Computer: MIKEMELGA
Description:
Error code 1000007e, parameter1 c0000005, parameter2 f5b6f228, parameter3 f6ed9bf0, parameter4 f6ed98ec.
Data:
0000: 74737953 45206d65 726f7272 72452020
0010: 20726f72 65646f63 30303120 37303030
0020: 50202065 6d617261 72657465 30632073
0030: 30303030 202c3530 36623566 38323266
0040: 3666202c 62396465 202c3066 64653666
0050: 63653839


Event Type: Error
Event Source: Service Control Manager
Event Category: None
Event ID: 7000
Date: 23-02-2006
Time: 20:16:26
User: N/A
Computer: MIKEMELGA
Description:
The Creative Service for CDROM Access service failed to start due to the following error:
The system cannot find the file specified.


Thanx in advance! (^_^)y
 

A:STOP Error (a.k.a. blue screen of hell)

Hi,

Zip 5 to 6 minidumps and attach the zip files here. You can find the minidumps at the folder \windows\minidump
 

3 more replies
Answer Match 84.84%

This computer was given to us in April 2011. Shortly after we got it, my daughter reports that she started getting different warning messages but she didn't pay attention to them. The previous owners said they never had this problem. The main one we get now is a blue screen with one of the following messages listed before the dds log.The only way to use the computer is to pop the battery out and restart it. It might do it on Startup, after a few hours, or even in Safe Mode. It also takes over my search engine sometimes.

It came with Norton 360. After this problem started, I got rid of Norton and installed Malwarebytes, Spybot, SuperAntispyware, AVG, and Zone Alarm. They are all updated, and each time I run them, they find some problem almost every time including Trojan.Hiloti, Rootkit.TDSS, MyWebSearch,Trojan.Trecur.XGen, Trojan.BHO, PUM.Disabled.SecurityCenter, and others. They always say they are removed completely, and often on the next scan it is clear, but then they either reappear or a new one with a different name pops up. I think it's all the same. I tried System Restore, but all the dates before May have been removed.

These are the messages (I've listed 3):
A problem has been detected and Windows has been shut down to prevent damage to your computer.

IRQL_NOT_LESS_OR_EQUAL

If this is the first time you’ve seen this Stop error screen. Restart your computer. If this screen appears again, follow the steps:

Check to make sure any new ha... Read more

A:Blue screen with Stop Error Message

Good evening. Download TDSSKiller.zip from Kaspersky from here and save it to your Desktop. You will then need to extract the file(s) from the zipped folder.
To do this: Right-click on the zipped folder and from the menu that appears, click on Extract All...
In the Extraction Wizard window that opens, click on Next> and in the next window that appears, click on Next> again.
In the final window, click on Finish
Please close all open programs as this may result in a reboot being necessary.
Double click TDSSKiller.exe to begin. Click Start scan and allow the tool to do just that. One the scan has completed, if the tool has identified anything allow it to carry out it's default action(s) - you'll need to click Continue where appropriate. Finally, if it prompts you to reboot your machine, please click Reboot Now and ensure that your machine does so.
If the scan finds nothing, please click the Report button and let me have a copy of the text file that opens. If you reboot your machine, the log, which i'd like to see, will be located at the root of you hard drive as C:\TDSSKiller.Version_Date_Time_log.txt.
Please check that you get the one with the right date and time.

25 more replies
Answer Match 84.84%

My computer has the following specs :-

CPU: AMD SEMPERON 2400+ 333Mhz FSB
HARD DISC 80 GIG 7200 RPM
Motherboard : Asrock K7S41-GX333FSB & 400DDR
Memory : 1GB DDR Memory
Video Card : REAL 256 INTEGRATED 3D GRAPHICS GPU
DVD-RW : YES
Floppy : 1.44MB Floppy Drive
Network Card : 10/100 Fast Ethernet Network Controller
USB : 4X REAR USB, 2X FRONT USB PORTS
Sound Card : 5.1 3D audio processing unit (APU)
Case : ice box zorro gamer ATX Case w/450 WATT PS and Front USB Ports
Keyboard / Mouse : Ezkey Silver/black 10 Hot Key Button Mouse & Labtec Internet Keyboard
Speakers : Made by Trust
Operating System : Windows XP Pro with SP2 (Although this error happened before sp2 was installed)
Monitor: Digimate L-1715 17" TFT Monitor

I keep getting Stop 0x000000C5 error. I've tried taking the memory out, as i previously had a 256mb in too, I've tried installing Logitech Mouseware, i've tried re-installing Windows, i've tried getting updated drivers off the Motherboard website and i really am running out of ideas. It's only a month or so old!!! I've had a look on the Microsoft Support site and it suggested running Driver Verifier but this is only supposed to be for Windows 2000. Plus it's not very clear how to do this. Does anyone have an idea what i can do?
Does anyone know of a solution? Or failing that, how do i run driver verifier?
 

A:Stop 0x000000C5 Error Blue Screen

http://support.microsoft.com/?kbid=291810&sd=RMVP
 

2 more replies
Answer Match 84.84%

Hello,The background: I am trying to install Windows XP Home onto a semi-new (custom built) machine. I am using a Gigabyte GA-G41MT-USB3 motherboard, a 500gb SATA hard drive (brand new), and 4gb DDR3 ram (2x2gb cards). It is an old copy of Windows XP - it may have SP1 included but I'm not sure.The problem: Computer POSTs fine, detects HDD fine (according to BIOS), RAM tests fine, enters BIOS setup fine, starts Windows setup fine. But... During setup, after Windows loads files, drivers, etc., and just after the point where it says "Setup is starting Windows", it goes to a blue screen with the following error message, every time:"A problem has been detected and Windows has been shut down to prevent damage to your computer.If this is the first time you've seen this Stop error screen, restart your computer. If this screen appears again, follow these steps:Check for viruses on your computer. Remove any newly installed hard drives or hard drive controllers. Check your hard drive to make sure it is properly configured and terminated. Run CHKDSK /F to check for hard drive corruption, and then restart your computer.Technical information:***STOP: 0x0000007B (0xF78D2524, 0xC0000034, 0x00000000, 0x00000000)"Steps I took: After reading about other people having similar problems, I assumed that it was because I was trying to install an old copy of XP onto a SATA drive. My machine doesn't have an A:/ drive, so I downloaded nLite and integrated the drivers fro... Read more

A:Getting blue screen Stop error during XP install

Please post your last session.ini

19 more replies