Tech Problem Aggregator

Approx. 20Gb of system disk space "missing" - Intel X25-M G2

Q: Approx. 20Gb of system disk space "missing" - Intel X25-M G2

Hello, my system disk is an Intel X25-M G2 80Gb (74.4Gb) and I recently discovered that there is a rather huge discrepancy in used disk space.

According to disk properties I have used up ~73.7 of the 74.4Gb, but the actual files on the disk are only 51.7Gb if I show all hidden/system files, mark everything and check size and WinDirStat report the EXACT same thing.

I have no pagefile on my system disk, no hibernation file and no system restores (it's actually disabled).

So any ideas whatsoever what this could be? It's starting to become rather annoying to "lose" 25% of my system disk. I've run diagnostics and haven't been able to find anything, I've googled it extensively and found others with similar problems, but the only solutions I've found are pagefile, hibernation file, system restores and of course disk cleaning - all of which I have checked already.

A: Approx. 20Gb of system disk space "missing" - Intel X25-M G2

Hello Zeilon, and welcome to Seven Forums.

The tutorial below may be able to help you ID what may be using the SSD's space. Option 1 with WinDirStat is a good starting point.

Hard Disk Space - Free Up and Recover

Hope this helps,

3 more replies
Answer Match 102.48%

Hello everyone,

I am currently a new registered user and was wondering if this was the correct place to post my problem. I have a issue with my Local Disk (C:/ Drive) and was wondering what was taking up so much space. I have a 1TB hardrive, currently on my Local Disk I have 136GB free of 454 GB. However, when I add up what I can find when opening the drive, it doesn't add up anywhere near the 317GB that it says has been used.

Now, I have currently installed...CCleaner, Eusing Regcleaner, AVG Free 8.0, and TreeSize, all of which I have run various times (still learning about TreeSize).

BEFORE I was getting scared because I had even less memory free (approx. 74.9GB of 454GB). But after running a Disk knocked it down to it's current state. It still doesn't explain how I have so much memory used.

My only thought now is that there are extra copies of my folders and files. Or most likely this has something to do with Vista's "System Restore". I am not very adept at using this PC. Whatever advice you guys can give...try to dumb it down for me and tell me where to go (e.g. Control Panel>Systems>etc..)

And my System Specs are incomplete because I don't even know where to go to get all that information! So if you need to know something about my PC tell me where I might find it or just look at what I have for my System Spec.

Thank you very much, I'll be checking my post at least once a day so I'll try to respond quick if any of you pros have an idea... Read more

A:Local Disk/System Restore/"eating" up space

Hello Mike, and welcome to Vista Forums.

This tutorial will help you see how much disk space is being used by System Restore and how to adjust the MAX size it can use. With a 1TB drive, it will have a high MAX by default.

System Restore - disk space

Hope this helps,

3 more replies
Answer Match 102.48%

Hi there,

I am facing a problem with the backup program of Windows 8. My computer (Asus with 250SSD) disk is new and I just installed my programs. Now I want to create a System Image using Windows. The image should be around 50go. Everything works fine until I get a message error saying my external disk does not have enough space, which is impossible since it is completely empty (500go).
Did anyone have ever meet that problem and/or have advices to help me? I would like to solve that and not be forced to used another way to backup.

Thank you,


A:Create system image failed - "not enough space on disk"

Is your second disc formatted NTFS?

7 more replies
Answer Match 102.48%

Using XP SP-1, 40GB HDD
A folder named "System Volume Information" has been created in each drive (C:,D:,E:,F: )
and consuming significant disk space day by day. Whether deleting these folders will create any problem. Any other technique to stop increasing the size of these folders ? Please suggest.
Presently consuming more than 3 GB in total.
Sometimes I need system restore to speed up the PC (besides other registry tools ) ..therefore this function is enabled in the system.

A:Too much disk space consumed for "System Volume Information"

9 more replies
Answer Match 98.28%

Dear Experts,

I have created windows image on Drive F: but delete it after some time manually due to some space prob.
But while backup shows about 40 GB only few GB space got free after deletion. When i try to again take the the backup using windows 7 backup & restore option, its still shows 35 Gb of System Image in drive F: when i brows the Manage Disc Space option but i cant find it on the same drive. (Plz see attached pic)
Plz help me to locate this and delete the same.


A:Cant find "System Image" of 36 GB but its shows on "Manage Disc Space"

Hello sattyaji, and welcome to Seven Forums.

It may still be showing if the system image was created as part of a Windows backup. Using the tutorial below to reset Windows Backup should clear it for you, but you will need to set up your backup again afterwards.

Backup User and System Files - Reset to Default Configuration

Hope this helps,

5 more replies
Answer Match 96.18%

Here's the story. I bought this new Samsung 840 250GB SSD.
I first did a clean install of windows 7 on it and it worked fine. Windows installed without much problem and everything. Then something didn't look right about the partitions. It looked like because I had all my HDDs connected while installing windows on the SSD the windows created the system reserve on the old HDD rather than the SSD. So I went back and decided to start from scratch with all the HDDs except for the SSD disconnected. I tried reinstalling windows on it but this time it didn't work. I tried formatting the SSD and it just gave me an error saying windows couldn't install on a GPT disk. I went into bios, made sure the PC was booting from the UEFI DVD drive and it still kept giving me the same error.

So I then booted up my old HDD. I tried formatting my SSD and now I can't delete the partition!
This is what my disk set up looks like:

If I click "extend volume" on the "New Volume (G" disk, it says "there is not enough space on the disk(s) to complete this operation".
If I try to create a "new simple volume" on the "unallocated" partition, it says the same...

Have I destroyed my new SSD now?! I just want it to work like a new clean disk...

A:If I try to "extend volume" it gives "not enough space on the disk(s)"

Hiyya Tracing try doing it with Partition Wizard mate Best Free Partition Manager Freeware and free partition magic for Windows 7, Windows 8, Windows Vista and Windows XP 32 bit & 64 bit. MiniTool Free Partition Manager Software Home Edition.
Brilliant tool if you can't do anything with the partition them just wipe the disk mate and start over with this SSD Alignment

1 more replies
Answer Match 95.34%

Hi all,

Sorry to repeat a question I see a lot of instances of, but none of those seem to be addressing my problem correctly.

I have not done anything new to my computer in recent days, so this problem has caught me off guard (I see most instances of this problem come after upgrading to Windows 7, I have had Win 7 installed for a while now).

Here is a summary of my problem:
1) My computer recently got stuck on the "Starting Windows Screen." So I manually held the power button to reboot.
2) On reboot, it said there was a need to run a startup repair, which I did. Everything checked fine, except for the last one which said "System Volume on Disk is Corrupted," which it claimed to have successfully fixed.
3) After rebooting from repair, the system gets stuck on "Starting Windows Screen" for a good 10-15 minutes, after which it runs a registry check. After it completes that I get hopeful -- but the screen then gets stuck on an all black screen with just the mouse cursor and nothing more.
4) Additional note: Attempting to start the computer on "safe mode" leads safe mode startup to become stalled on "DRIVERS\CLASSPNP.SYS"
5) The lastest attempt to repair yielded this message: "Startup repair cannot repair this computer automatically.
Problem event Name: Startup Repair Offline
Problem signature 01: 6.1.7600.16385
02: 6.1.7600.16385
03: uknown
04: 21201099
05" AutoFailover
06: 2
07: Corrupt Volume
OS Version: 6.1.7600.... Read more

A:Stuck on "Starting Windows", Repair Shows "System Volume on Disk is Corrupted"

Hi Stan, Hopefully I can help you out....or at least lead you in the right direction. From my experience, the symptoms you are suggesting sound like perhaps a dying Hard drive.

1. Do you have the windows 7 boot disks that came with your computer or when you bought the Operating System? If so, you could try and insert one of those and boot from it, and attempt to repair the installation. (this won't affect your data, only the windows system files).

2. If that doesn't fix it, you could try a fresh reinstall of windows 7, and see if that works.

3. If neither of those work, its likely that because of the fact that when windows is repairing itself, it is generally putting copies of its system files in the same physical location on your disk. Because your disk is obviously not completely dead, ie....its still loading to the windows 7 startup screen, its just copying files to the bad sectors on your hard drive and gets stuck when loading. This is especially my guess because you said Safe mode is having same problems, even after attempting to repair. In the past, I've tried and salvage a disk by reformatting it and only leaving on partitions which do not contain the bad clusters. This takes some time, and some guess work.....and really this is only a "bandaid" fix because once the disk has bad clusters, its only a matter of time before these things give out. You wouldn't want to trust your important data on it anyways....

I hope this leads you in ... Read more

1 more replies
Answer Match 89.46%

I just upgraded from Vista Home Premium to Win7 professional x64 hoping to fix the above mentioned problem. After a complete re-install Im getting the same errors.

Im not sure of the proper terminology here, but during startup the computer does a scan of all hardware and "Volume 0" has a "failed" message.

The odd thing is that sometimes after a few restarts and pointless boot menu visits the computer starts up fine.

I tried windows repair feature by booting from the disk, but when I get to the window where i select the operating system to repair, its empty. Drive C, where the operating system is, is not showing.

I have a feeling that the hard drive itself has gone bad and is very unstable. Please let me know if I'm missing something or we just need to get a new HD.

Thank you

A:Win7 pro startup error "Boot MGR missing"/"Operating System Not Found

What type of hdd do you have. For example if you have a Seagate drive, there is software you can run to do a diagonostic on the hdd before the operating system boots.
This would be a good idea, especially if you were having same issues when Vista Home Premium was installed first.

Do you have more than one hdd installed. If yes, make sure in BIOS settings, the proper drive is selected for First Boot. And better yet make sure its the only drive attached when booting.

9 more replies
Answer Match 89.46%

Newbie here. I have searched around for a while but have not found a post with my exact situation.

I just installed a new Seagate Momentus 500gb (7200rpm) SATA drive in my Lenovo X61 laptop and have been working on a installation of Windows7 Ultimate.

Not realizing this was an upgrade install disk, I tried to install Win7. I didn't know about the clean install method, so I started over with an installation of WinXP (slipstreamed to deal with the SATA drive).

Next, I ran the Custom Installation upgrade to Win7.

So far, it seems to be working ok.

However, the Local Drive is D: instead of C:. The System Reserved drive in labeled C:. Should I be concerned? Should/Can I change this?

Attached are screenshots of Disk Management and explorer window.

Thank you for any info.

A:"System Reserved (C:)" and "Local Disk (D:)" ??

Try removing the System Reserved drive letter in Disk Management to see if Win7 claims C instead. It sometimes works.

There is no reason you can't operate with Win7 as D even though it is meant to always assume the C letter unless it's installer is run from another OS.

But if you do I would not allow a drive letter for SysReserved as programs can write to and corrupt it, especially the ability to make Win7 backup images.

Now that you know you can clean install Win7 without needing XP on the HD, I would strongly consider booting the installer to do a Custom install, choose Drive Options to Delete all partitions, Create new as you wish, then Format before installing to first partition after SysReserved it will create for you. The installer will see an OS at boot to allow use of Upgrade version key upfront during install.

Here are tips to get a perfect reinstall - use the ones which apply: Clean Reinstall steps

2 more replies
Answer Match 88.62%

Hi everybody, I've made a lot of progress with this external drive, but I seem to be stuck now.


Unidentified problem with 3TB external drive (USB 3.0 enclosure) that the computer suddenly started treating as RAW. Spent the last two weeks running CHKDSK /r repeatedly. Slowly got through many hundreds of indexing errors. Now I get as far as "verifying security descriptors (stage 3 of 5)," but I seem to have hit a wall here...

CHKDSK won?t go any further because there is "Insufficient disk space to fix the security descriptors data stream."

Microsoft?s advice (Error Message:) is of no help to me. They say to ?delete some unneeded files from the disk and try again,? which doesn?t help me since I can?t get the drive to mount or stay mounted long enough to copy the files onto a different drive.


The drive behaves differently each times I power up its enclosure, but it is usually one of these things:

Drive doesn't mount.
Drive mounts after a few minutes. I see a generic "Local Disk L:" in Windows Explorer but, when I try to explore its folders, the computer takes about 15 minutes trying to read it (I can see the progress bar moving slowly across the top of the screen), and then says that "The parameter is incorrect." Drive disappears from Windows Explorer.
Drive mounts after a few minutes. I see the full Volume name that I originall... Read more

A:"Insufficient disk space to fix the security descriptors data stream."

Someone? Anyone?

8 more replies
Answer Match 88.62%

I have a C: drive which I want to increase in size. Under disk management there is 20GB of "Free space" - (right next to the C: partition). But neither disk management or EASUES partition manager will allow the partition to use this space. How to I change "free space" to "unallocated" so that it can be used ?

A:Cannot extend volume (disk management) although "free space" exists

Can you post a snip showing what you have? An image makes it easier for us to help you. For example, you said that there was 20GB of free space next to your C: partition. What you didn't say was whether it was to the left or right of it.

7 more replies
Answer Match 88.62%

My wife has a two month old Lenovo ideapad with Windows 7. We are now getting alerts that the D partition is near full. Is this system taking multipul backups of the harddrive C and storing them all? What are my best options to have a safe backup, but not overloading the D partition? I do see in; Computer>System>Device Manager>Disk Drives>D Drive General tab that there are two options at the bottom.
option one, (not checked in my case) "Compress this drive to save disk space".
Option two, (checked) "Allow files on this drive to have contents indexed in addition to file properties"
Would selecting option one solve my problem? If this system is saving a snapshot of D over and over, it will only be a matter of time when option one will be overcome.
SO, I would think that there has to be a setting that will let partition D delete older backups...right?

Would it be a combination of selecting option one and changing a setting that would enable older backups to be automaticaly removed?

A:Action Center "Check backup disk space" alert

Welcome to the forum
If your D drive is made for backup's only, you can delete all files exept the newest one.
But it's advised to make backup's on an external USB drive and change the frequency of backup's to your files and olso for images to your OS.

4 more replies
Answer Match 88.62%

Big Kudos to anybody who can solve this one! Very little/nothing on Google or microsoft support site.
Here's the problem:

I'm helping a family member who has a new Dell PC with Windows XP Home, Outlook Express 6.
Every time they close Outlook Express, the following Warning pops up:
To free up disk space OE can compact messages. This may take a few minutes. There are 2 options - OK and Cancel.

Here is the rub: We've closed the warning, or we've clicked OK, or we've clicked cancel, we've checked the box that says don't ask me again....these warnings continue to come up next time (EVERY time) Outlook Express is closed.

This is a senior citizen who has, maybe, 20 email messages and no shortage of memory or disk space. I want to prevent this warning from coming up ever again. How do I do it? Is there some default I can change somewhere?

A:Solved: "Free Up Disk Space" OE warning ?? Stop the Madness!

6 more replies
Answer Match 88.62%

I'm hoping this is a simple fix. I'm trying to fix my elderly uncle's Asus laptop. System Repair pops up and fails. I booted to command prompt and found out it may be hard disk space. 400+ GB Hard drive (only one drive) and there's only 1024kb Free. I'm thinking that could be the issue. Hardware was checked out at the computer store and is fine. But they were going to charge him $200 to fix this failure to boot up issue. I told him to let me try first.

Can I possible "compact" this drive from the command prompt screen?

Note: I have no other Win 7 systems, so can't create a disk, and I have no original disks.
Also, no restore point has ever been set, and there are no partitions on the drive.

A:"Startup repair" failing - hard disk space issue?

Normally, I'd tell you to download a program or two to examine what's using the space or to clean up unnecessary files.

But with only 1024 kb of space, you probably can't install anything.

So--try this:

Start button, search box, type in "disk cleanup" and then poke the disk cleanup listing that shows up.

Let it clean up the drive and report back with how much space you then have.

You'll see an option in disc cleanup where it asks if you want to clean up system files as well. Say yes.

It should calculate how much space it will recover.

Let it run to completion. Might take a few minutes.

Then check your recycle bin to see if it's empty.

Report back with available space.

9 more replies
Answer Match 88.62%

i heard this is way to much. what should i set it to?> or what else should i do?

thanks alot,


A:in my internet options, my "amount of disk space to use" is 8591 MB..?

It's down to preference really but you don't really need it to be set more than 200 mb's.

Hope that helps :)

1 more replies
Answer Match 88.62%

when i try to run word 2007 i get the following error message:
There is not enough memory or disk space to run word 12

I have 1Gb RAM with 550Mb free and 2Ghz Turion with 7Gb free space on the system partition and 15Gb free space in the other partition

can any tell me why its doing this?


A:OFFICE 2007 - "Not enough Memory or Disk Space to run word 12"..?

7 more replies
Answer Match 88.62%

When I couldn't delete the student office trial (which came installed with my HP laptop purchase) from "add/remove" due to having deleted first, a different but associated program (can't recall the name), I followed these tedious instructions found on this link -

The problem is...I noticed that instead of freeing up disk space, it took up more. How can I remove this trial completely to free up space?

A:Office Trial Removed From "Add/Remove" YET Ate Up Disk Space

ellaphant5 said:

due to having deleted first, a different but associated program (can't recall the nameClick to expand...

This can be a problem.

Also, I would say that fix from MS applies only to when the proper procedure for the uninstall of Office is followed but the end result is not what we expected so basically that didn't wasn't any help.

We need to know what other mystery "associated" program is.

1 more replies
Answer Match 88.62%

I know it reduces the overall file size of the folder or file in question, but what method does it use to do this?

If you are not familiar with this phrase, it appear if you right-click on a file/folder in windows explorer and select "advanced". When selected the file/folder name will turn blue.

I need to know for some work, I have to compress some work and I could merely show myself using this feature, but explaining how it works would be better.

Thank you

A:[SOLVED] What does "Compress Contents To Save Disk Space" do?

This compression method does not reduce the "size" of a folder, it reduced the "size on disk". am I right in thinking that this compression method does not alter the code of any files, it merely stores the folder in a way which saves space on the disk?

6 more replies
Answer Match 88.62%

I am attempting to transfer all of the files form an NTSF 250 GB external drive to an empty FAT32 250 GB internal drive via USB.

I keep getting an error message that says "Cannot copy (filename): There is not enough free disk space. Delete one or more files to free disk space, and then try again. To free space on the drive by deleting old or unnecessary files, click Disk Cleanup".

This is not true though, as the destination drive has more than enough space for the transfer.

A:False error - "not enough disk space" durring transfer

You cannot transfer all the files because many will be in use...

You will ned to make a drive image with a program like Ghost, or you can even use its drive copy feature.

It will be cake to copy an entire drive.

3 more replies
Answer Match 88.62%

I use microsoft office 2007 My computer is dual core 2.53 Ghz 3 GB memory and I have 91.4 GB free disk space.
I am using Windows XP Professional Version 2002 Service Pack 2
I work a lot with word and did not have any problem. Now i have a problem with one particular file that I can not open and I always get the error "There is not enough memory or disk space to complete the operation. " When I try to open the file File size is not so big 652 KB Any ideas what I can do.


A:Solved: "There is not enough memory or disk space to complete the operation."

What type of file? Where did it come from?

If you do not have file endings showing, you should. Be sure that there is not a hidden "exe" or "com" at the end of that file.

3 more replies
Answer Match 88.62%

I know this question has been asked before as I've read about it all over the Internet. In order to get rid of the 'Low Disk Space' message it says to go to the registry and locate HKEY_CURRENT_USER \ Software \ Microsoft \ Windows \ CurrentVersion \ Policies \ Explorer, type a new value, etc. The only problem is I don't have an Explorer key. It ends at Policies.

I've tried everything. I've tried creating the key myself, and I've tried inserting the value into the policies folder. Nothing has worked. Can anyone help?
Thank you

A:Solved: Can't get rid of "Low Disk Space" message on my recovery drive

I guess no one else is having this problem. Do you think this is a problem with HP?

3 more replies
Answer Match 88.62%

I got the warning msg that my drive "E" (system restore) was almost full. I did a disk cleanup, and a delete all restore points (including system...). After deleting approx 25 restore points and I've deleted down to 2 currently (new ones) and the only way I could get them to go was with CCleaner, My disk now shows only 4.2 free of the setting of 10.6GB. I cannot find what it taking up over 6GB on my recovery disk. What has it gone for....? I searched the internet several hours but can't find the answer. Any help appreciated...TJ

A:Unable to increase free space on Recovery Disk "E"

System Restore points take up space on C, rather than in E or a recovery partition in my experience. A recovery partition is normally put there by the manufacturer to allow you to restore to factory specifications if needed. I wouldn't ever deliberately put anything else on a recovery partition.

Who made this PC?

Can you post a picture of Windows Disk Management so we can see a visual display of your partitions?

3 more replies
Answer Match 88.62%

Hi - I keep getting the message that a backup failed due to less than 400 MB on the Windows disk. I have about 350 GB available on the disk!

Other backups have worked OK. I have seen a long thread on the Microsoft site with lots of people saying they have the same intermittent problem, but no solution. Anyone know what causes this?

I'm working Home Premium, and backup up to another hard disk on the same machine which also has lots of free space.

Thanks guys


A:Vista backup fails "not enough space on Windows disk"

Just a couple of simple questions, which you may have already covered.
How much space is on the C drive.(where Vista is installed)
On the 'Where do you want to save your backup' page, you are sure it is your second drive and not the 'Recovery' partition.

2 more replies
Answer Match 88.62%

Hi there!
First of all thanks for the great toturial and the forum.

I tried to do the in-place upgrade from Windows 10 (build 1607) in order to "repair" my system (there are some quirks I want to get rid off) using a freshly created USB (as per description), but it fails with the message "make sure that there is enough disk space available in your PC" (rough translation from german; see attached screenshot) without any further information.

It then automatically cycles back to the question on how to install (i.e. with keeping data and apps or without) and then back into the above mentioned error message.

This is what I already tried or made sure of prerequisites needed:
I have made sure that there is definitely enough disk space available.My C: partition (where windows resides on) is 106 GB large and has currently over 58 GB of free space available.The system partition that is supposed to be 350 MB is still 350 MB (I read something about this potentially being reduced to 100 MB by other tools ...).I have deinstalled the Kaspersky anti virus tool (reinstalled it now after several tries with no success).I have disabled (i.e. fully decrypted) the disk encryption bitlocker on all disks.

My partitions (as seen from "Mini Tool Partition Wizard" and "Disk Manager"):
Do you have any ideas on what else could be wrong?
What intrigues me most is the fact that there is no further information in the error message on what or where is missing... Read more

A:In-Place Upgrade fails with message "not enough disk space"

Hi, Mark and welcome to Ten Forums.
Have you tried to mount the ISO in File Explore, instead if using an USB stick?
I just download the current ISO here: Windows 10 ISO , mount it in File Explorer and run the setup.exe.

22 more replies
Answer Match 88.62%

Hello. I am having trouble with a message in Action Center in Windows 8.1. It is saying "Check Backup Disk Space" and I cannot hide the message. I had Windows 7 File Recovery setup with Windows 8.1, but now after the upgrade, the message is "stuck." Can this be fixed? These two links explain it perfectly:

Windows 8.1 Update - Check backup disk space - Microsoft Community

Windows 8.1, can't remove "Check backup disk space" error in action center - Ars Technica OpenForum

Please help. Thanks.

A:"Check Backup Disk Space" Error Windows 8.1

See picture:

2 more replies
Answer Match 88.62%

Is it possible this can do any harm to my computer?


A:Quick question about the option "compress drive to save disk space"

I have never knwon it to, it doesn't delete any of your wanted files, only temporary junk!

3 more replies
Answer Match 88.62%

I first notice my notebook begins to have this issue when I tried to update my Windows. It returned me with error code "80070008", which says that my computer might have run out of memory, however, there are 200GB space available
in my C: drive, and I am only using 27~30% of my RAM out of 8GB.
I tried to perform DISM 'ScanHealth' and it returned me "Error: 8 - Not enough storage is available to process this command".
At first, I tried to ignore this issue as I thought it did not cause me any major trouble. But I was wrong. Several USB devices become unresponsive (yellow exclamation icon at Device Manager).
When I tried to manually install drivers, that's when I found out it was this STORAGE insufficiency again that cause me trouble:

"Windows found driver software for your device but encountered error while attempting to install it.  - Not enough storage is available to process this command".
Some of my programs also become incredibly laggy ever since this issue arises, yet I don't know where the problem lies. 
At Event Viewer... I noticed several error messages regarding
"Windows was unable to load the registry. This problem is often caused by insufficient memory or insufficient security rights. - DETAIL: Not enough storage is available to process this command".
I also caught a glimpse of one error that I think stated more clearly:
"Application popup: Windows - Low On Registry Space: The system has reac... Read more

More replies
Answer Match 88.2%


I uninstalled Ubuntu, and I installed Windows 7 because I couldn't restore my system, but a free space went missing with no reason, and I am not sure if I deleted the d drive or not. Furthermore, I lost more than 800GB. A page pops up when I start my laptop, and it shows that I still have the free space, but it is not shown either in computer or disk management as unallocated. I have tried so many programs to get back the 800GB and use it, but nothing seems to work. I will attach two pictures, the first one shows my disk management, and the second picture shows the page that pops up everytime I start my laptop. Long story short, I installed Ubuntu using Wubi, then I didn't like it that much, and I tried to format d drive, then I deleted by mistake. Now the d drive is shown, but missing around 800GB. I am really pissed

I am not sure how many Gbs that exactly I am missing, but it is around 800GB
I will appreciate your help, please.

A:D drive space is missing, and I can't allocate it "ubuntu"

Up up up

8 more replies
Answer Match 88.2%


I recently bought an Asus 1215n netbook from Amazon with a 250gb hard drive. However, when I check the actual capacity I only see 1 partition with 100gb and another partition with 117gb.

I know you "lose" 7gb per each 100gb, but that means I should at least have 232,5 usable gigabytes (approximately). I checked other posts in the forums and thanks to them I found out that one partition in my computer is using 2gb for system protection.

But still, where are the other 13,5 gigabytes???

Thanks everyone

A:Missing Hard Drive Space (besides the "standard 7%")

Quote: Originally Posted by reckonn


I recently bought an Asus 1215n netbook from Amazon with a 250gb hard drive. However, when I check the actual capacity I only see 1 partition with 100gb and another partition with 117gb.

I know you "lose" 7gb per each 100gb, but that means I should at least have 232,5 usable gigabytes (approximately). I checked other posts in the forums and thanks to them I found out that one partition in my computer is using 2gb for system protection.

But still, where are the other 13,5 gigabytes???

Thanks everyone

Sorry to say but that 7% is an average. I have seen as high as 20% and as low as 3%.

It gets worse the bigger the HD as well.

2 more replies
Answer Match 88.2%

There's not enough disk space on drive C where Nero 7.57 is installed; but, there is on drive E. I set Nero's cache folder to E:\NeroTemp and and Windows temp and tmp environment variable to E:\Temp where there is over 100 Gigs of free space and restarted the computer; but, there is no change with Nero's insufficien-disk-space error.

And, yes, I did create those folders for drive E.

What to do?

A:Nero aborts with "not enough disk space" error.

9 more replies
Answer Match 88.2%

I had the same trouble. I had never backed up my hard drive before i had kind of run into it so i figure what the hay i'll try it. It told me to back it up on the D drive or disk. (since i didn't have a disk setting there i figured i would back it up on D drive) Well after a few min. it said i didn't have enough space. So i figured Oh well. I didn't need to back it up. Well EVERY TIME I Reboot the computer now it tells me I'm low on disk space on drive D.
Now everyone know D drive doesn't have alot of space it has your system on it. But why now is it checking it all the time. When it tells me to clean it , it shows me where and there isn't anything to clean. THIS IS ANNOYING! HOW DO I MAKE IT STOP?

There is no screen to give a shot of. It's a little icon on the task bar that pops up. Than when you click on it it says delete unused files. When you click on it it gives you the list of files you can delete. BUT there is only two things on it and both are all ready empty. One is recycle bin.

A:[SOLVED] How to stop "low disk space" messages

Hi Rachel3790 and welcome to TSF !

It's better to start your own thread so that we keep one thread for one user. Here's a link to the related thread you first posted into :

Which program did you use to backup your system drive ?

If this is an HP computer have a look at the link advised by Mon in the other thread :

Else, when disk space is running low, Windows may advise you to run the disk cleanup utility which allows you to delete temporary files and empty the recycle bin, among other things. Since this doesn't help it means that your hard drive is simply filled with your own data and the data from the programs you installed on it. The backup you just created is probably also taking some space and if you don't need it you should just delete it.

What you need to do is copy some files on CD's or DVD's, on an external drive or to another computer. You should uninstall the programs you're not using anymore using add/remove programs and you can also delete some old documents of yours in your "my document" folder if you don't need them anymore.

Be careful not to delete any system file or folder. Files that are safe to move away are video and music files. These media files usually take plenty of space and you can free that space if you burn them on CD's or DVD's and delete them from your hard drive.

If you have no idea what's using up space o... Read more

4 more replies
Answer Match 88.2%

Windows Update trying to install KB2976627, continually receiving error that I do not have enough disk space remaining to install the update. My OS Drive has 75 GB Remaining. Does anybody have any idea what causes this problem and how to remedy it?

A:Windows Update error, "not enough disk space..."

Time to do a Cleanup of your system:
Windows Update Cleanup in Windows 8

4 more replies
Answer Match 88.2%

I used Creative Lab's Wave Studio for years with a single problem.

I loaded it onto my sister's computor and the first time I tried to save a file, I got an error message saying:

"There is insufficient disk space to save (file name)."

She had several gigs of open space so I just chalked it up to something funky of her PC.

A few weeks later, my HD crashed, so I installed a new one and re-loaded my software. When I fired up my Wave Studio (version 4.02), I got the same message. Now I had roughly 75 GIGS of free space.

I'm not a newcomer to the world of software troubleshooting, but this one has me stumped.

Any help would go a long way to restoring my sanity.


More replies
Answer Match 88.2%

Doing some maintainence on my computer, i am considering doing this option: "Compress drive to save disk space". There is also a "compress old files" to save space

are these both the same things? (same drive)
can i undo this options? im a big fan of reformatting to undo problems in the event its challenging to undo compress a file.


A:"Compress drive to save disk space"

6 more replies
Answer Match 88.2%

I receive daily a "Low Disk Space" error message which is incorrect and in my estimation fradulent. It goes on to give an alternative to rectify this situation by offering to "Speed up your computer and remove all viruses that are on your computer." Of course all of this is for a price. If you opt in and then change your mind before you totally commit they offer the same package for half price. I refuse to be "sucked in" by this fraudulent company.

I have gone to the internet to try and find out how I may get rid of this enemy. I have used Malwarebytes, Microsoft Security Essentials and Microsofts Security fix program all to no avail. I am at my 'wits end' trying to rid my computer of this plague. This is the url that the message comes through as. I cannot find out any source that will identify its origin:

I need help.


Doug. Bell

A:Fake "Low Disk Space" error message

16 more replies
Answer Match 87.36%

My drive, according to properties under C:\, is using 45.5 GB of its available 100. When I go in to C, and select all (hidden files are shown), properties, it counts it up to 30 gigs size on disk.

So.. Where's those 15 gigs?

I wasn't sure where to put this so I plopped it in Vista, as it's what I'm running.

My system is a rather new (last month) box, pretty clean overall.

A:"Missing" hard drive space

10 more replies
Answer Match 87.36%

I got a Gateway Pc...
I am supposed to have 400 gb of space but currently there is only an available space of 372 gb?
I have no other Os installed.
The 372 gb is not free space, but available space...
I tried everything... defragging..deleting the whole partition and reinstalling the OS... e.t.c...

A:Hard drive space "missing"

7 more replies
Answer Match 87.36%

"Not enough memory to run microsoft excel. Please close other programs and try again"
So this morning I tried to open up excel, and this message comes up. Same happens for word.
Then I try and open it again and it wants to run in safe mode, and then the same problem happens.
Then I open it again and it says "Excel failed to launch in safe mode. Do you want to start Detect and Repair?"
So I run that and it says setup completed successfully. But I try and open it and I get the original "not enough memory" message, and it's just a big loop.

I have enough memory, 3GB and I'm using office 2007 on windows 7.
It's been running fine since this morning.

A:"There is not enough memory or disk space to run excel"

How about diskspace that's ' memory' too.
The environment settings voor %TEMP% could be invalid?

3 more replies
Answer Match 87.36%

Forgive me, but I?m new to the forum and relatively new to [rebuilding] computers (compared to some of you, I?m sure?) I do have a tech background.

Having said that, I had to do a re-install of XP (SP1) on a Dell Optiplex GX620 that I have. While at it, I upgraded the HD to 1.5TB (Seagate Barracuda)

The XP install went well. I did not have a restore disk for the drivers, so I went to Dell?s driver download website and downloaded the correct drivers for my model/service tag.

I put the drivers on a USB flash drive and moved them/loaded them onto the Dell. I installed the drivers in order and most installed fine. A few however, such as the Broadcom 57XX Gigabit Divers, are telling me that I am out of disk space. I get the error and a dialog box says that the volume on the C: drive is -650GB, and I have -655GB Available, with 2328KB Required and Differences of -650GB? I have no-idea what?s going on here, but I can?t seem to install the driver(s).

I did Disk Clean-up, defrag, chk disk, Ccleaner? blah, blah, blah? I am only using 1% of the available drive capacity.

Any ideas?

A:New O/S and driver install "Out of Disk Space"???

BUMP... Does anyone know whats going on with this? It's a simple re-install and driver install problem; not a virus or anything weird.

Someone has on this forum has HAD to have seen this before.

Please help.


5 more replies
Answer Match 87.36%

I have to harddrives, drive :C/ and drive D :/ drive c has the basic miniums and came with 16 gbs of space which is completely full with windows , then drive d has 136gbs and is 103gb of free space left
ANYTHING i try to download i try to make it go to Drive D but none the less i keep getting the error "not enough disk space"

this is a brand new system, that a friend whos good with computers built for me for my gaming needs, i have a

intel r core tom 2 quad cpu 6600 @ 2.40GHz 4 gb ram 64 bit operating system..

if you can help or need any info please let me know where i can find the info for you on the computer im pretty crappy with computers so i need all the help ican get

A:keep getting "not enough disk space" with 2 hard drives

anyone have any ideas? this is getting really frustrating....

2 more replies
Answer Match 87.36%

In Explorer on Computer, is there a way to change the number of gigabytes or percentage that Windows uses before it changes from the blue bar to red? For instance, I have an array that is 1TB, but it still has over 15GB free on it, but Windows interprets that percentage as the drive being low, so the bar appears red.

To me, I don't want that bar red unless there is say, 5GB remaining, or maybe even 1GB. 15GB still goes a long way, even though it is a small fraction of 1TB.


A:Changing the Disk Space Bar "Low Level"

Quote: Originally Posted by muzicman82

In Explorer on Computer, is there a way to change the number of gigabytes or percentage that Windows uses before it changes from the blue bar to red? For instance, I have an array that is 1TB, but it still has over 15GB free on it, but Windows interprets that percentage as the drive being low, so the bar appears red.

To me, I don't want that bar red unless there is say, 5GB remaining, or maybe even 1GB. 15GB still goes a long way, even though it is a small fraction of 1TB.


15Gb out of 1Tb would be considered low to me.

2 more replies
Answer Match 87.36%


I have recurring problem, which I have noticed on PCs other than my own. The used space on my hard disk drive is approximately 5GB higher than the total of all the files on it. (It's always been around 5GB, every time I've seen it). The only thing I can do is to reformat the disk, and it will be fine for a few months, and then the same amount will "disappear" again. Disk cleanup, ccleaner, etc don't help, and it's not the recycle bin or temporary files.

It happens on my primary (Windows XP) partition, but not on the secondary partition, and last week it happened on my external hard disk after I deleted a large quantity of data.

I only have 60GB in total (30GB on the primary partition) in my laptop, and 40GB on the eternal drive, so its pretty annoying to lose 10GB. If it makes any difference, my external drive is a 2.5" laptop drive, a Hitachi Travelstar, NTFS formatted. Not sure what brand is in the laptop, but it's FAT32. But I've seen this happen on a friend's desktop too (again only on the primary partition).

Any ideas why this happens and if I can do anything about it that doesn't involve reformatting?


A:"Lost" hard disk space

Tell me if I'm teaching you to suck eggs, but what size blocks do you have on your drives, because without decent sub-block allocation, you'll often lose parts of blocks for files when they're smaller than the block size. Even with sub-block allocation, you'll still lose a bit because of the overheads, but 5GB seems a little steep for that size of disk.

If I compare my size of files, with size on disk, I'm losing ~1-2% of the disk. That's with the default block size of 4K. But it probably depends on the number of small file you have around the place.

After deleting a large number of files, it's probably worth-while running a disk cleaner to make all the blocks contiguous again, and that should give you back most of your space, but if they are really not getting re-allocated as free space, then I'll have to dig more.


1 more replies
Answer Match 87.36%

I am trying to copy a 9gig video file to my Seagate external USB 2 drive for back-up.
The drive has 140gig available, but I keep getting the "not enough free disk space" warning when I try to move it and it will not allow it to be copied.
What am I missing? is it a format thing?

A:Solved: "not enough free disk space"

6 more replies
Answer Match 87.36%

I am getting this window popping up every 2 or 3 minutes despite clicking on it and ticking the usual boxes to remove the unwanted files - 3 minutes later back pops the warning

its as if the pc doesnt know I'm actually doing it

I have followed this advice given to someone else on another site

"Insure the temp files in the hidden Local Settings folder are deleted.
Start>My Computer> Local Disk C> Computer user name> Then go to tools (at the top)> Folder Options>View and put a dot in show Hidden Files and Folders Click OK> Open the Local Setting Folder>Temp> Delete all the files you can in the temp folder.
3. Run Disk Clean from the Start>All Programs> Accessories> System Tools>Disk Clean Insure you remove all the compress old files.
4. Get Rid of the Restore points and Lesson the amount of disk space System Restore uses.
Right click on My Computer>Properties>System Restore and put a check in turn off system restore now click on the Settings Button Choose a setting of 1 - 5% click apply and OK
Go back and TURN ON system restore, insure the amount of disk space for system restore did not default to the Max amount."
but it hasn't made any difference whatsoever

could this be a virus? I ran malaware and then 'search and destroy' but that made no difference either

I have an Acer Aspire T1 2OE

A:incessant "low disk space" warnings

16 more replies
Answer Match 87.36%

I'm getting the Low Disk Space message in Windows XP. Well, DUH...I knew that I was running out of room, so I bought an external hard drive with more space than I'll ever fill. Like an idiot...when I got the external.....I just went to folders...sometimes programs and used "send to" the now G: drive. Yes, I know, that was STUPID! Many of the same files are duplicated, etc so that they were copied and sent....not actually MOVED. Some of my programs don't even work correctly anymore.

I know that I can do a system restore....but I'm almost afraid that it might crash my pc. What is the easiest way to fix this problem and put everything else, except my bare essentials, on the bigger drive?


A:The dreaded "Low Disk Space" message

bumping this hoping to get some help

3 more replies
Answer Match 87.36%

I frequently get a notice that the disk space on my D drive is low and asking me if I want to clear up some space by using the cleaning utility that came with Windows XP Home Edition. This disk is my secondary drive and I know the space is low. Is there a way that I can get rid of this annoying notice that appears on my screen every so often? Thanks.

A:Solved: Notice of "Low Disk Space"

Hi referee07,

The "clean up unnecessary files" is safe to use. You can also add
choices in the list of what's to be deleted. You can also safely
remove all temporary files... Search for "*.tmp" (without quotes)
and delete those.

Also the trash bin standard setting is 10% of your drive. I would
adjust that downward to 2 % on all drives.

And, of course, you can delete some things that you really don't
need, or put them on a CD if you have a burner. Hope that helps.

2 more replies
Answer Match 87.36%

Hello people, I have an external 500 gigs drive with over 100 gigs free and a partition on a RAID 0 with 500 gigs free. I was trying to copy a folder with 25 gigs of data from my external hard drive to my 500 gigs partition, until at about copying 2.5 gigs, Windows shows up a warning saying that there is not enough disk space and that the file (was 500 Kb...) could not be copied. I skipped it and kept doing the same thing for every subsequent file... whats my computer's problem? I have WIndows Vista Home.

A:Solved: "There is not enough disk space" warning

16 more replies
Answer Match 86.94%

Ok, I built a PC a month ago and everything seemed find no problems of any sort. The other night I defragmented my hard drive and shut it down and turned it on today to a memory test and the message "Disk Boot Failure, Insert system Disk and press enter"

The computer has access to the XP pro w/ sp2 disk only as a boot device but it will not recognize it now.

I have set Cd-rom as 1st for boot sequence then hard drive I have no floppy drive and the bios has been configured to know that.

I am not sure if this means anything but in the bios the IDE Channel 0 Master says none and when I try to turn on auto detection it wont detect a hard drive.

The HDD is fully connected and has not been touched since I installed it a month ago.

I have this awful feeling that I fried the HDD when I defragmented it last night.

Any help would be very much appreciated. But please be simple this is my first build and my knowledge at this sort of thing is very very sketchy at best.

A:Error message "Disk Boot Failure, Insert system Disk and press enter" on first build

The first thing to do would be to get a new data cable for the herd drive and see if that fixes it, they are nice and cheap nowadays.

4 more replies
Answer Match 86.94%

Ok first off I want to say I've searched and searched and searched to no avail in trying to find a solution to this I've come to the conclusion it's software and not hardware based. Let me start from the top.

I've had an older computer (HP Pavilion a408x) out of commission for a while due to a 'sploded psu. I finally get around to ordering one, install it and everything is good. I bring it back to my office and hook it up to the internet and as expected there's updates. So I up date it and after the updates are installed the computer restarts automatically (weird yes) and as it's coming back on it detects errors and runs CHKDSK. So I let it run and it gets to part 2 of 3. At this point in time my partner is really needing to print sometime and all computers print through this computer. So after about 45 minutes CHKDSK is still on part 2 at only 15%. So I'm like "screw it" and manually shut down and restart. It's at this point I get a "primary master hard disk failure" at the boot screen. Letting start up continue I get a "Stop : c000021 unknown hard error \systemroot \system 32 \ntdll.dll" At this point I realize something is delectably wrong.

Found this thread, which didn't help much. At some point the c000021 error stops and I start getting "disk boot failure insert system disk and press enter" and I found this thread, which didn't help much either. I have also been searching other sites as well.

Here's what I found ou... Read more

A:Hard Drive not found "disk boot failure insert system disk and press enter"

Anything would be super helpful, even if it's bad news. I just need to know if I can get this remedied or not.

Another thing I noticed is that the HDD activity light on the front of the computer does not blink or show any activity.


7 more replies
Answer Match 86.94%

I had a fresh install of 7 and everything was working fine.
All of a sudden it starts randomly freezing and programs start responding.
I got KERNAL_PAGING_ERROR BSODs etc. and got a new disk, thinking it was that.
After cloning the new disk which didn't work, and produced loads of errors on chkdsk, I decided to do a clean install of 7.

I still keep getting "Disk boot error, insert system disk and press enter", and when it does boot, it freezes all the time and every time I click the start button, it basically crashed and is messed up.

Tried new SATA cable and ports. Any ideas?

A:Windows 7 freezing, "Disk boot error, insert system disk and press enter"

BIOS settings or Motherboard issues?

Have you checked with the manufacturer website for the Motherboard that you have the Windows 7 drivers?

Is your Windows 7 DVD a retail copy...or the pre release BETA....or dodgy(in which case problems might lie there)

1 more replies
Answer Match 86.94%

I just built this new computer (everything new) but when I start it up it gives me this message, and I cannot open my disc (probably not recognised?). Please help resolve this.
Btw. no operation system installed or so.

my computer:
CPU: intel i7 920
Motherboard: gigabyte GA-ex58-ud5
Sata-II hdd
+ cd writer is SATA as well

Could it be that I need to update my bios somehow? I highly doubt it's the hardware as it's all new

A:"disk boot failure, insert system disk and press enter" But CD-drive won't open

8 more replies
Answer Match 86.94%

I recently purchased a laptop with Vista installed. When I view the properties of my hard drive (120gb, showing 111gb) it says that I have used 49gb in storage space. However when I open it and select all the folders inside (including hidden) it only adds up to 29gb.

Is there some other folder type that isn't being displayed? I have yet to backup my files so it can't really be that either. And either way 20gb seems an awful lot of lost space.

Any help is appreciated.

A:Missing ~20GB of harddrive space

I would recommend that you get gparted. download the iso and create a livecd from that. Then boot into that and see where all that space is. It might just be unpartitioned space. If so you can add it back in your vista partition with gparted and you will be all set.

To create the livecd. I would recommend imgburn as a program to use. It is free as far as I know.


4 more replies
Answer Match 86.52%


I recently purchased an Intel X18-M G2 80GB and installed Windows 7 on it. So far, so good.
First thing I installed afterwards was World of Warcraft and I then noticed that I had very little free space left on the drive - less than 25 GB i.e. about 50 GB used.

If I mark all the folders (with show hidden files and folders enabled) and it informs me that the total amount of space used is 32 GB.

Where did the last 23 GB go? I've disabled the System Restore and it freed up about 5.5 GB, so I now have about 30 GB free, and the total amount of storage used according to folder properties is 25 or so GB.

Any suggestions?

Thanks in advance!

A:Hard disk space missing @ Intel X25-M G2 + W7

Download TreeSize Free and run it. However, don't be alarmed or concerned with the C:\windows\winsxs folder. It will appear very large, but is really just hard links to files elsewhere. Primarily use this tool to find directories outside of C:\windows that are large.

I too have the Intel X25 Gen 2...I just have the M edition. With Win7, about a dozen software apps (Open Office being the largest) and Wolfenstein installed, I have about 53GB free.

I have a second drive on my system that I use for downloads and storage.

Upon installation, things I did
--turn system restore down to 1% of hard drive
--move page file from C:\ to my D:\ drive
--disable hibernate (powercfg -h off)
--moved my IE and Firefox caches to my D drive.

9 more replies
Answer Match 86.52%

just like the title says my HD crashed and i could not boot on the computer i put in a new HD and tried to boot it would not work. i would see the HP screen but then i would get the error. it is a 810a model and help would be extremely appreciated. and if you really know you can email me at <email removed>

A:Installed new HD now getting "disk boot error inset system disk & press enter"

14 more replies
Answer Match 86.52%

Hello everyone, been lurking for a while, but first time posting because I could use some help. I tried looking through other threads, but nothing seemed to help. I was downloading a game off of Steam, and my family computer just crashed. It apparently restarted itself, and presented that disk boot error message. Tried restarting again using ctrl+alt+del, and same situation occurs. I go into the BIOS screen, and try to use the auto detect to identify the drive, but it is not identified. All of the cables are working correctly, as I plugged a different drive into them and that drive booted fine. Btw, the hard drive is a western digital 5000AAKS.

I'm running an AMD Athlon 64 Processor 3800+, 2412 MHz, 2 gb of ram, Windows Vista Home Basic. Its a Compaq SR5110NX. I'm not overclocking it or anything, just downloading a game, and then this happened. Any help would be greatly appreciated.

A:Another "disk boot failure insert system disk and press enter" thread

7 more replies
Answer Match 86.52%

Hi there,

Well, the message I get it pronounced above in the title. I know a little bit about computers, but I don't know how to get into DOS, BIOS, etc when I don't have a start menu to do so. I read some other threads and they seemed to have useful information, but I would need further explanation. Also - I hooked my HD into another computer to see if it would work, it did, booted up, everything. Also, when I went into Boot Setup or something - blue screen and the only thing I could do when hooked into my computer - it doesn't show any options for booting - it says select from the list - but how do I do that when there's nothing in the list? Oh please do help me as this computer is my main source for writing.


A:Problem: "Disk Boot Failurs, Insert System Disk and Press Enter"

If you're running a HP what it's asking for is your System Restore Disk. Meaning the HP OS that came with your system. Finding Bios in HP are generally simultaneously with Start button on casing F1 or F11. If neither key works then try F2 and or the Delete button. Making sure each key is pushed as you boot up.
Once your in Bios use the arrow keys to scroll up and down your bios - the enter key once on the various listing in menu until you find your boot sequence listings. In general plus and minus are used to change the sequence. CDrom HD and floppy is the correct setting. But with your Restore Disk from HP it might not even require all that.
Pop it is and Boot up and see if it works. Then try the Bios sequence if you can get there, the F10 to save and enter making sure your CD with the OS is in your CDRom when you do.
Let us know as things go...Jazz
Sounds like you've either lost your OS or you've lost your HD.

2 more replies
Answer Match 86.1%


My cousin recently made me a computer and he sent it all the way here from the United States. I was eager to try it out and hooked it up to my monitor, mouse, keyboard, etc. I did not plug in any additional USB devices.

When I boot up the computer it gives me "DISK BOOT FAILURE, INSERT SYSTEM DISK AND PRESS ENTER".

I couldn't get past this (I don't have the Windows XP disk), and so I restarted the computer and pressed 'Del' to get into the (I think it's called BIOS menu? Not sure, the blue screen thing), I looked at the boot up priorities and moved Hard Disk to one priority level above Disk boot, however this made no difference.

I am good with the computers but not when it comes to hardware and things like this. So PLEASE if you use a term I may be unfamiliar with please explain what it is. I am very frustrated and disappointed that this does not work.

Thank you very much,


A:"Disk boot failure, insert system disk and press enter"

Welcome to TSG!!

I'm guessing that, perhaps, a cable has come loose during shipping. Open the computer's case and look around. Usually the hard drive is mounted toward the front of the system. It's a device about 3.5" wide by 5" long and about an inch thick. There should be two cables plugged into the back end, one of which comes from the power supply, the other should be plugged into the motherboard.

2 more replies
Answer Match 86.1%

System disk needed to access IBM 486 SLC2-V1/387;
66 mhz cpu clock; 640k base memory;7296k extended
memory; 5.25 & 3.5 disk system.

A:"Disk boot failure. Insert system disk and press enter."

Welcome to TSG

Which version of Windows are you using (win95)? Always make sure there is no floppy accidently left in the drive. Did this message just start one day or did it begin after some problem you had?

2 more replies
Answer Match 86.1%

New build computer, spec is as follows;

Biostar GF 7050-M2 Motherboard
AMD Athlon 64 4400 Processor
1 IDE 250GB Maxtor HD
1 IDE 200GB Maxtor HD
1 SATA Samsung 20x Dual Layer DVD-RW

Now I have assembled everything to the best of my knowledge correctly, I can boot the computer to BIOS without any problm whatsoever.

The problem is when I either try to load the motherboard driver disc, or my Windows XP disc I get this message;

"Disk boot failure, Insert system disk and press enter",
I have tried setting my disc drive to first boot device, I have even unplugged my two HDs as well, but to no avail.

My last hope is my USB flash drive, onto which I have copied the software from my motherboard driver disc.

Dores anyone have any suggestions as to how I fix this?, I will be very grateful to anyon that can give me some form of help,


A:"Disk boot failure, Insert system disk and press enter"

Is there an OS already installed on the drive you are trying to boot from?

3 more replies
Answer Match 86.1%

Pretty much what happened is that my powersupply got messed up one day and just turned off my computer and I couldn't boot it back up. I ordered a new PSU and I installed it but now when I boot my computer I'm getting "Disk boot failure, insert system disk and press enter". I've tried putting in the installation disc and using the recovery options but my OS isn't listed/found and if I click load drivers I can clearly see both of my hard drives. I have already checked boot options as well. I was also using GRUB before this all happened as well because I installed ubuntu as a dualboot. Any help would be greatly appreciated

A:"Disk boot failure, insert system disk and press enter"

Boot the free PW bootable disc - ( make sure NUM LOCK is on when it asks about screen resolution, then press 1, then Enter)

See what it says.

Free Download Partition Wizard

I assume both HD's are recognized by BIOS?

9 more replies
Answer Match 86.1%


I'm currently running on a m2n32-SLI Deluxe WIFI edition with a 320GB maxtor harddrive. Previously, I had my set up like this: One SATA from maxtor to the mobo, one IDE cable with my cd drive, as master, and my old HD(30 GB w/ my documents) as slave. It was running fine with Vista on the maxtor. However, I wanted to remove the old HD and place a new CD-drive in. I did so, and I received the above error message.

I took out the the new CD-drive and switched back to my old connection, and it worked great.

Then, I had the 320 GB connected, and the old cd-drive to the IDE. I get the error message. I've tried every single possible combination of jumper settings and replaced the IDE cables.

What do I need to do to get this to work, before I throw my computer out the window?

A:"Disk Boot Failure, Insert System Disk And Press Enter"

Windows has detected the change as an attempt at piracy. You will now have to reinstall Windows in repair mode, then talk to Microsoft over the phone to get it re-established.
This is common with OEM versions of Windows. Windows will detect any change in the hardware, other than memory, as a possible attempt to bypass the Windows Install parameters... it thinks the computer has been changed.
You might want to do a thorough search of the knowlege base.

4 more replies
Answer Match 86.1%

Disk Boot Failure. Insert System Disk And Press Enter

Hi i have a self built Quad Phenom 9850 XP Home ed PC that wont boot, i will say now i am very much a newbie to this so sorry in advance.

When i turn it on there is a very long wait at the set-up screen (an s-series gigabyte M750SLI-DS4 board ) and when it gets to boot screen it builds the DMI pool, tell me there is a data change and to update new data to DMI! and then goes to boot, only giving me this instead "DISK BOOT FAILURE. INSERT SYSTEM DISK AND PRESS ENTER"

I have not yet managed to get the computer working, the thing that gets to me the most is that less than 12 hours ago i was sat on the computer with it working fine and no errors..

AMD Phenom 9850 2.5GHZ
Gigabyte S-series M750SLI-DS4 board

There is alot to loose on this computer so i am very much hoping this wont be the case, Thank you in advance.


A:Disk Boot Failure. "Insert System Disk And Press Enter"

6 more replies
Answer Match 86.1%

I've tried showing hidden files: no dice.

I've tried using chkdsk, but it says that there isn't enough space to recover the data. It's about 280 or so GBs of "missing" data.

What can I do? There is irreplaceable data on this drive.

A:Files "missing" but space is still used

9 more replies
Answer Match 85.68%

Hi everyone,

I've been having this prblem for several months but recently it has been getting worse. I'm working on an Dell Optiplex gx280 windows xp professional sp2. Here is the problem, while I'm working on my computer (doesn't matter what I'm doing) I will get an error msg "low disk space" flash on my screen, then my monitor will shut off, but the power light on the computer stays on (sometimes flashing). I'd have to power it off and turn it back on and it would log in normally. This morning it happened 3 times, please help. Thank you in advance.


A:"low disk space" error

6 more replies
Answer Match 85.68%

I have a Compaq Presario with Windows XP Home Edition. I keep receiving the above message. How do I get rid of it? Yes, I know it means I don't have enough disk space on my D Drive, but how do I fix it? It won't defragment because it needs more space (I have only 45 mgs.) My D Drive is solely for Restore so I cannot delete files from there. Can I enlarge the D Drive?

Thanks, gb

A:"Low Disk Space D Drive"

16 more replies
Answer Match 85.68%

One of my users was working in Corel Word Perfect 9.0 and experience an "out of disk space" error when she tried to save her work (just a small document). She was working over our TCP/IP network using Win2000 terminal server and saving to a Linux file server. I was at the server so I was able to save the file with a different name but I can't figure why she would get that error as there is plenty of space on the Linux server. Has anyone ever seen this before? Thanks

A:"out of disk space" error

Just a wild guess but is there possibly a setting somewhere that may limit the amount of storage space a user can use, on a user by user basis? If so, you may just need to increase the setting for that user.

2 more replies
Answer Match 85.68%

I keep getting "Low disk space" messages about one of my partitions.

First of all, what is the point of this message? I can see why it would be useful for the system drive, but for all other drives why would anyone worry about filling up a drive?

More importantly, how can I disable this message from persistently popping up every day?

A:What are "Low disk space" messages for?

Hello Marty,

It's basically just a warning to let you know that the disk/partition is extremely low on free space. This is to warn you to either clear space or get a bigger storage device soon since you could lose data, possibly everything, on the hard drive if you run out of space on it.

The tutorial below can help show you how to disable the "Low disk space" message. Low Disk Space Warning in Vista
Hope this helps,

9 more replies
Answer Match 85.68%

Good afernoon,
yesterday in the evening I got a BSOD which consequently generated an Error Submission to Microsoft, whose answer to that problem was that the ACPI system missed a driver for the Power Management of... the AMD Phenom processor.
The funny thing is that the platform could not be farther from AMD family of hardware, being an Intel i5-750 on Asus P7-P55D motherboard.
Everywhere in the system (Vista Business x64), the processor is correctly recognized.
So where could this come from?

Thanks in advance for any help

More replies
Answer Match 85.68%

Hi, now I am on new PC and I installed Win8.
But when I install graphic driver, it will write Not meet minimul requirements.
Then is my Win8 so slow.
EDIT: In WinUpdate was a small log:

Intel - Other hardware - Intel(R) Management Engine Interface
Installation date: ‎3.‎2.‎2012 17:47
Installation status: Failed
Error details: Code 80240FFF
Update type: Recommended
Intel Other hardware software update released in October, 2010
More information:
Winqual Help
Help and Support:
Select a Product Solution Center
(Was this important?)
Please help..
- ExtremeElite

P.S. I tried replace the igdlh.

A:Intel HD 3000 " Not meet minimum system requirements "

what model is your computer?

3 more replies
Answer Match 85.68%


I'm trying to restore my computer to a previous point in time (earlier today) using the "System Restore" utility. After I select my restore point and click on "Next", I'm noting in the next screen ("Confirm disks to restore") that my C: drive is showing a "not enough space" status (as opposed to the expected "Ready to Restore" status). Do I need to do something as simple as clearing out files from "temp" directories?

To complicate matters slightly: I'm unable to boot into the Windows GUI. When I power up the computer, the "Startup Repair" window stating "Your computer was unable to start" appears and attempts to correct the problem. After a few minutes, it reports that it cannot repair the computer automatically and presents me with a "System Recovery Options" window. Since the initial Startup Repair was unsuccessful, I'm choosing not to select that option I thought the "System Restore" option would be the next best approach. When I try to perform the System Restore, I run into the scenario that I detailed in the first paragraph of this post.

Any help would be greatly appreciated, and I'm more than happy to post additional information as required.


More replies
Answer Match 85.68%

I am using a 120GB portable hard drive for back ups and additional file storage. When defragging this drive, you are able to see how much space is actually "reserved for system files". Since this is not a bootable drive with no operating system on it, is there a way to recover this space that is reserved for system files? On this drive it amounts to about 10GB of space. If possible, how is this done?

A:Portable Hard Drive "reserved system space"

8 more replies
Answer Match 85.68%

Hi Everyone,

i am using CRichEditCtrl::GetLine() function to read the text from a dialog.
If my text contains any space character then it is throwing improper argument error and the application getting closed in vista only.....
What is the actual problem ????? why it is happening with vista only...?

Please suggest

More replies
Answer Match 85.26%

HP probook 4510s windows 7 32bit
I did a "disk sanitizer" and the laptop isn't rebooting right or reading my operating system cd it says "NON-SySTEM ERROR OR DISK REPLACE AND STRIKE ANY KEY WHEN READY"
1) i removed all assceraries from the leptop
2) ran a diagnostic test all passed
3) here are some photos attachments
4) i think i deleted the partition and the OPS wind.7
Please thanks

A:HP 4510s windows7 "Non-system disk or disk error replace..."

What is a "Disk sanitizer." Sounds like a disk wiper, or some optimizing or registry cleaning crapware that ruined your Win7.

Try booting into the Win7 DVD or Repair CD to System Restore to before you ruined the OS as shown in Troubleshooting Windows 7 Failure to Start which also provides the DVD if needed.

If you can't get it started with any of the steps given there then get the superior Clean Reinstall without the HP crapware which is the worst in the industry and throttles Win7 from its native state.

2 more replies
Answer Match 85.26%

My mom has an HP Compaq nc8430 computer. She recently encountered this problem this morning. Does this mean that the hard drive's dead? Any help is appreciated greatly

A:"Non-system disk or disk error, replace and strike any key when ready"

DId ur BIOS detect ur HDD? Also check if ur sata cable is loosed or not. U can try another pair of sata cable & test it if it works or not..

8 more replies
Answer Match 85.26%

My dad sent my daughter a "E Machine" with XP Home. Before he sent it, he transferred all of his personal files. When I hooked it up, the screen said "Boot disk failure. Insert system disk and hit enter". The company sent us a new set of bootable CDs as we thought the problem might be in the CD. Same message. HELP!!!

A:"Boot disk failure, insert system disk and hit enter"??????

16 more replies
Answer Match 85.26%

Vista system restore attempt throwing "not enough space" status

I'm unable to boot into the Windows GUI. When I power up the computer, the "Startup Repair" window stating "Your computer was unable to start" appears and attempts to correct the problem. After a few minutes, it reports that it cannot repair the computer automatically and presents me with a "System Recovery Options" window. Since the initial Startup Repair was unsuccessful, I'm choosing not to select that option I thought the "System Restore" option would be the next best approach. When I try to perform the System Restore, I run into the following scenario . . . after I select my restore point and the restoring files activity is complete I recieve and error 0x80070070 and a message citing not enough space. My C: drive has 19Gb free so is the lack of space in a partition and if so how can I change it?

Any help would be greatly appreciated, and I'm more than happy to post additional information as required.


More replies
Answer Match 85.26%

After our Dell Inspiron E1505 recently crashed , Dell talked us thru diagnostics and finally sent us a replacement(refurbished) Toshiba hard drive to install in our computer. After installing it, and reloading all of the software for Windows XP, MS Office Small Business 2003, drivers and utilities, using the discs that came with the computer, we have a "Found New Hardware" window that pops up - Wizard trying to install a "Base System Device" everytime we turn the computer on. It asks for a disc but none of my existing ones seem to be the correct one. I've given it permission to connect to the Internet to "find" the software but nothing works.
Also, since the crash/re-install, our C drive only has 12.4 GBs of total disc space, and of that, only 1.2 is still free space. My D drive has about 37 GBs of disc space. Could these two problems be connected? The computer was running so slow and we would periodically get a message "low virtual memory". This weekend, I moved as many of our documents as possible to the D drive to try and free up space. It's a little better, but why do I have such a small amount of disc space? Help!

A:recurring message to install "base system device"-unsuccessful & low disc space

7 more replies
Answer Match 85.26%

I recently had DK8 do a boot-time defrag/chkdsk and consolidation of files and folders. As a result the "Reserved System Space" seems to have disappeared. (It's normally fairly large and white with a criss-cross green grid as per the legend left lower side.)
Why is that and need I be concerned?

A:Solved: Diskeeper 8 Pro and "Reserved System Space"

10 more replies
Answer Match 84.84%

I have an old HP Pavilion 8260 that I got for free which is having some odd issues. Any time I try to boot, I get one of these 2 errors (first it was always Operating System Not Found, now it's Missing Operating System).

Here are the steps I've tried so far: I tried to boot from a floppy with a disk I know works; tried to boot off of the CD Rom; Tried disconencting everything except Floppy, CPU, and RAM; Tried resetting the BIOS by selecting "Set to Default" and by pulling out the CMOS battery (it was after doing this that it switched to the Missing OS error message).

The hard drive is dectected in the BIOS, as is the CD Rom and floppy drive. It properly recognizes the amount of RAM.

I am fresh out of ideas, even though I'm generally pretty good at this. If anyone else has any advice, it's greatly appreciated.

A:"Missing Operating System" or "Operating System Not Found" errors...

7 more replies
Answer Match 84.84%

Hi all,

Installed a DVDRW drive but comp crashed when installing some software and it stopped detecting my Primary Master and Slave drives. I've fiddled about with the Master and Slave configs and have managed to get it to detect my HD and DVDROM.

I've unplugged my DVDRW and my small HDD and am trying to get windows to load up.

After using FDISK /MBR an rebooting, I get "Missing Operating System".

Tried installing Windows XP after formatting, it seems to have installed but it's not loading.

Current config:

Slave: Pioneer DVDROM (not the DVDRW)
Master: Seagate 80GB (C: = 15GB) & (D: = 61GB).

D: has files on there that I'd like to recover. Too big to put on floppy.

I've run a search for similar problems and tried some of the solutions but no good. Any ideas? Thanks

A:"Error Loading Operating System" to "Missing Operating System"

12 more replies
Answer Match 84.84%

Please can somebody help with this minor but annoying matter. When turning on my business computer one morning, the space bar and return/enter buttons are visable when i type emails, but when i send them, they are not. I know its a setting, but can anyone tell me what setting and how to turn it off?


A:[SOLVED] &quot;Space bar&quot; and &quot;return/enter&quot; are visual on emails! Help

You need to tell us what email client you use as these days not everyone uses the built-in one.

4 more replies
Answer Match 84.42%

Laptop is showing NTLDR is not working. I was told to use the Install Vista cd that came with the laptop but whenever I hit a button the same message shows up..NTLDR is missing. Seems like it does not know the cd is there ? Any help would be great. Thanks

A:Dell Inspiron(1521) "NTLDR is missing" and disk don't work...HELP!

Originally Posted by lonewolf123

Laptop is showing NTLDR is not working. I was told to use the Install Vista cd that came with the laptop but whenever I hit a button the same message shows up..NTLDR is missing. Seems like it does not know the cd is there ? Any help would be great. Thanks

You need to go into BIOS and make sure the dvd drive is checked so it can be booted from.

3 more replies
Answer Match 84.42%

Hi Guys, any ideas how to access my external hard drive [TOSHIBA MK3029GACE] device manager can see it but it does not appear in disc management.

I use this HDD perfectly in my car HDD player. But when I try to connect it to my Laptop, it does not show up in disk management.

Please check the attached screen shot..

Thanks for the help....

A:HDD shows in "Device Manager" but not in "DiskPart"or" Disk Management

Specs show that drive has a ATA-6 interface (P-ATA, or IDE). How are you connecting this drive to your laptop? Does the laptop have a PATA or SATA connection? Does it use an adapter?

1 more replies
Answer Match 84.42%

When I installed Windows 7 Pro x64 today, I did a custom install but I didn't format my drive beforehand. After it restarted the first time, it came up to a screen that said this:

Windows could not start because the following file is missing
or corrupt:
< Windows root>\system32\ntoskrnl.exe.
Please re-install a copy of the above file
After several failed attempts my Dad somhow got it to install properly, and it worked fine until I needed to reinstall updates. When it restarted again, the same screen came up. I put in the Windows 7 DVD and restarted, this time it booted without any problems. My boot is setup as "Boot from CD/DVD Drive" first, and "Boot from HDD" second. But when it said "Press any key to boot CD/DVD" I didn't press anything, and it just moved on normally.
I ran the startup repair but it did not find any problems.
So can somone tell me how to fix this?

A:"ntoskrnl.exe is missing or corrupt"appears unless disk is inserted

Is it the problem now?

Quote: Originally Posted by bomberswarm2

My boot is setup as "Boot from CD/DVD Drive" first, and "Boot from HDD" second. But when it said "Press any key to boot CD/DVD" I didn't press anything, and it just moved on normally.
I ran the startup repair but it did not find any problems.
So can somone tell me how to fix this?

It is not anything abnormal. If the Optical Disc Drive is set to be the first boot device, then every startup will try to boot from it. If there is no bootable disc in that ODD, it will not show the "Press any key to boot CD/DVD" notification, and will automatically search for the second boot device, which is the HDD.

Remove the windows disc from the ODD tray, and try startup your computer. Let us know the results. Is it still saying ntoskrnl.exe is missing there?

Also, let us know the source of the windows disc. It may be a corrupted one itself.

3 more replies
Answer Match 84.42%

When I boot up my computer, after the "welcome screen" from expressgate and my ASUS motherboard I get the error:
"BOOTMGR is missing
Press Ctrl+Alt+Del to restart"

I did a search on fixes for this error and was told to insert my Windows 7 install disk into my DVD drive. I use a downloaded version of Windows 7 so I didn't have an install disk, so I downloaded a pirate .ISO of a Windows 7 install disk and burned it onto a blank DVD+R disk, and then tested it on another computer to make sure it worked normally and didn't have any malware.

I put this DVD+R into the PC with the BOOTMGR problem and restarted it, but my computer showed no sign of recognising that there were any disks in the DVD drive. I thought that the install disk must have been faulty so I tried to insert my Ubuntu DVD+R but my computer did not recognise that either.

I thought that the problem might lie in my boot order so I pressed "Del" at my motherboard and reconfigured my boot order settings so that my DVD drive was the first priority (though for some reason, my motherboard lists it as a CD drive instead of a DVD drive). I tried both DVD+R disks again and my computer still didn't recognise that I had inserted anything into my DVD+R drive; it did not prompt me to press any key to boot from the disk.

I have had this computer (put together by my brother so I have no hardware manufacturers to seek tech support from as far as I am aware) for nearly two years and I i... Read more

A:"Bootmgr is missing" Windows 7 install disk not recognised

You're positive it's a DVD drive? You've successfully read a DVD with it, and it says "DVD" somewhere on the front?

When you are again able to boot into your legit (I hope) Windows 7 you can create a bootable repair disk: Start - All Programs - Maintenance - Create a System Repair Disc.

If your BIOS includes a hard drive diagnostic I'd run that.

1 more replies
Answer Match 84.42%

Hi, my sister has Sony Vaio E-Series which runs windows 7 Home edition. She encountered a problem starting up the windows and decided to use Recovery Disk, Recovery Disk stopped working and needs additional source (disk) to run. She weren't successful so decided to stop recovery and run it again. After that the error "BOOTMGR is missing" appeared! When I put the recovery disk inside the machine it doesn't work. F8 and F4 keys also don't work. So I can't use the similar solution mentioned on the internet like running "system restore". She also doesn?t have Windows 7 installation disc to run.

Please help me solve this problem

A:Error "BOOTMGR is missing"_It doesn't allow me to use recovery disk

We always assume you have made your Recovery Disks using the OEM manufacturer's Recovery Media Creator app the first day you had your new PC.
& made the Startup Repair CD.
startup repair disc-create

Did you make the OEM manufacturer's Recovery Disks?

How to make Sony Recovery Disks:
View Document

How to use Sony Recovery:
View Document

How to use Sony Hardware Diagostics:
View Document

How to order Sony Recovery disks:
1.Go to
2.Enter your computer's model number (for example, PCV-XXXX), and click List Parts and accessories.
3.Follow the online instructions to order the Recovery Media Kit.
If you are not able to access the Sony Direct Accessories and Parts Center Web site, contact a customer service representative at 1-800-488-7669.

2 more replies
Answer Match 84%

Well I have been trying to fix this error for hours And after the system recovery scan it says there are problems with my start up options but I cant hit those buttons because the s2 keyboard I have in simply wont let me. Secondly I have ran the repair tool but it says I have to manually fix this problem so I tried using the command prompt but to my great luck again I cant get to that option because of my keyboard so I think the real question here is what do I have to do to my keyboard to land over all of the settings? Please help its Friday and I want to chill with my friends.

A:"BOOTMGR is missing" Need Help With Repair On The Windows 7 Disk

Have you looked in the bios & checked your boot order?

5 more replies
Answer Match 84%

I am experiancing really big problems using my Acer Travelmate 4202LMi Laptop.

I cannot hear any sound, I cannot use my webcam, and I can't use the Acer Empowering Technology. I have tried to use the System Recovery disks to re-install windows... and It gets so far into installing it, then says "Cannot Install Operating System, Missing Partition" or something along those lines.

I need a free and easy to use software that will allow me to re-install windows on my laptop using the recovery disk.

Thanks for any help given!

A:"Missing Partition" - Acer Recovery Disk

16 more replies
Answer Match 84%

Hello, i recently posted a reply in another forum about this issue. I wasnt having any luck there so maybe someone could help me. I looked over some of the posts on other forums but my situation is a little different. Here it is. A friend of mine was using my computer one day and it just crashed on him. Now it will boot up and the memory test is fine but when it goes through the drives it reads primary hard disk....none. The floppy drive and cd-rom drives read fine. Then it proceeds and comes up with the message "disk boot failure, insert system disk." What could be the problem here? He does not have a floppy boot disk for the computer. Would a boot disk created by another computer with Windows XP help? Any ideas of how to get back into the computer without losing the hard drive?

A:Need help "Disk boot failure, insert system disk"

have you tried undoing the IDE cable and then re-plugging it back in? I know sometimes ive had the kind of problem when putting together a old machine. I end up just redoing my cables and it will come on. Then again if it dosent work I usally end up putting a diffrent HD in instead. Im kinda new here so i prolly dont have the best advice but it the only thing i can think of.

This might sound stupid, but ive seen it more than enough times. I think its only on older machines, but if you leave a floppy disk in the drive, shut down, and then turn the machine back on with the floppy in. The computer will say something along those lines and not boot into windows. All you have to do is take out the flopply and restart.

Best of Luck to You! :giddy:

4 more replies
Answer Match 84%

I recently purchased a 2nd hand computer thru a local ebay dealer - HP DX6120 ST 2.6 GHZ 80GB HDD 512MB RAM DESKTOP PC.

When i boot up, it displays: Invalid system disk Replace the disk, and then press any key

Then i reboot and press F8 & del and it doesnt go to bios settings, it just gives me a screen that gives me an option to "boot from..."

I select the hard drive.
Get the same response... "Invalid system disk Replace the disk, and then press any key"
Then I put in a windows XP pro Disk (the computer has an official XP Pro License Key on the case, as stated on the specs on selling page) and then rebooted.
I still get the "Invalid system disk Replace the disk, and then press any key"
I change the boot to CD and i get Windows Set Up options.
I pick install Windows XP and the it starts loading dll's etc.
Then it says i have no previous version of Windows idetected and wont let me go any further.

I assume that it is trying to upgrade, but i dont get an option to do a fresh install, just "Install Windows XP"

I am not sure if ;
there is a windows actually loaded,
I need to reformat,
The bios battery is flat
or if i need to do something completely diferent.

If i am to reformat, i cant remember the cmds/or how to do that when there is no windows to do it from.

I hoe you can help me.


Old Fart

A:"Invalid system disk Replace the disk, and then press any key"

Find the make of the hdd, go to makers website and download and run
the diagnostic utility.
If you want to wipe the drive do a google for killdisk, its free. Run it
this way you are assured of a clean drive.
The diganostic utility may also be able to write zeros to the drive, doing
the same thing. At this point dont take the short route out and format
with windows, leaves to much garbage behind. But after the drive is
wiped you will have to format with the wind disk and install the os.
Sounds like you have a bad drive, or a confused drive..
I dont think that board does raid, but you should double check in bios.
If raid is enabled disable it..

2 more replies
Answer Match 84%

A friend has an old Pentium 1 HP Vectra 500 PC. On startup it says "Invalid system disk" like if you had a disk in the floppy drive. There is no disk in the CD or A drive. I took the A drive and CD out of the boot sequence via the bios and it made no difference. Is it the hard drive?

A:"Invalid system disk" error w/no disk in drive

6 more replies