Tech Problem Aggregator

Can i monitor and control multiple router connected devices data???

Q: Can i monitor and control multiple router connected devices data???

I have tried to research this and am not finding the information I need to answer the above question so hope a networking expert can help.

I recently for the first time went over my monthly data cap for broadband and looking it to it a bit more it looks like a lot of the programs my kids are using are hogging the bandwidth. I don't really want to pay for more bandwidth (as I already pay way above average as I live in a small rural village) but I don't want to restrict too much what my kids are doing.

The solution to me seems to be to see if I can monitor and if possible control to some extent the data on each of the IP connected to the router if that is at all possible.

I have looked at my router settings and unfortunately they do not permit anything more than traffic monitoring and there are no custom firmwares to allows additional features of any use.

Is there any software that I could use to do this?

Can anybody help at all with any advice about whether this can be done?

A: Can i monitor and control multiple router connected devices data???

It is almost impossible to restrict the total usage of bandwidth. To my knowledge there are no setting for that in normal routers/gateways.

1 more replies
Answer Match 90.3%

This is my first post and glad to be here among experts. I will list my issue, please tell me what information you need to be of assistance.

I have a net gear WNR2000vs with the latest firmfware to date. I have two wired devices connected: 1. my pc 2. xbox, and also one wireless device connected 1. my cell phone via wi fi.

Before I updated the firmware:
I would hard wire my 360 and pc to the router together. My 360 online play would work fine for about 10 minutes then my connection on my 360 and pc would drop. My network status would say 'resolving issue'.

After updated the firmware:
I now have my 360 and pc hard wired to the router together. These two seems to work fine together. When I try to connect a wireless device my connection drops. My pc resolves the issue and regains connection, but if I try to navigate a webpage or download anything from the wireless device then it starts the whole dropping connection thing again.

I'm not sure what information you guys would like but here's some basics. Thanks!

Tech Support Guy System Info Utility version 1.0.0.2
OS Version: Microsoft Windows 7 Ultimate, Service Pack 1, 64 bit
Processor: AMD Phenom(tm) II X4 965 Processor, AMD64 Family 16 Model 4 Stepping 3
Processor Count: 4
RAM: 8190 Mb
Graphics Card: ATI Radeon HD 4600 Series, 1024 Mb
Hard Drives: C: Total - 305142 MB, Free - 100720 MB;
Motherboard: MICRO-STAR INTERNATIONAL CO.,LTD, 790FX-GD70(MS-7577)
Antivirus: Kaspersky Internet Security, Updated and ... Read more

A:Net gear router losses connection when multiple devices are connected

11 more replies
Answer Match 78.96%

AJA System Test fails on one or more of the external USB 3.0 hard disk drives connected under USBIF compliant USB 3.0 Hub (VIA KGH / Cypress HX3 / Microchip) which is connected to the Type-C port of Dell XPS13 running Windows 10, 64 Bit OS. Test Setup and steps to replicate the issue: 1. Self powered USB 3.0 hub connected to the Type-C port of the Dell XPS13 using a Type-C receptacle t0 Type-C plug. 2. Four USB 3.0 Hard disk drives connected to the downstream ports of the USB 3.0 hub. 3. Following test tool is installed and run (4 instances run, one instance each for each of the hard drives connected to the Dock) https://www.aja.com/assets/products/files/90/AJA_SystemTest-2.1.0-x64.msi Following are the tool settings:3a. 'Test File Size' = 512 MB3b. 'Settings > Run Continuously' selectedThe tool does continuous cycles of read / write to the selected Mass Storage device 4. USB traffic is captured on the upstream port of the USB 3.0 hub in continuous recording mode 5. One of the instances of the tool reports failure to access the drive after about 10 to 30 minutes after starting the test. Stop recording the USB traffic.
Sample set of Mass Storage devices used:
1. SinapisTek Poseidon Pocket SSD 128GB 2. Apacer AS710 USB 3.0 Portable SSD 128GB 3. Seagate Expansion 1TB HDD 4. BUFFALO HD-PZFU3 1TB HDD

Other observations:
1. Issue not seen on other Windows 10, 64 Bit platforms (Intel Series 7 chipset Desktop, latest Macbook, etc.)
2. During the test, it is ... Read more

More replies
Answer Match 71.82%

Hi

I have a THOMSON TG585 v7 DSL router and when I browsed devices connected i found 2 unknown devices and apart from my 2 pcs, a switch and a media player I have nothing else wired and the wireless option is disabled.
 

A:unknown devices connected to DSL router

Obvious question #1: do you learn anything by clicking on the unknown devices?

Obvious question #2: do the unknown devices correspond to the switch and media player (check the MAC addresses)?
 

3 more replies
Answer Match 70.98%

Hi,
In the past 3 days I've noticed that I periodically get randomly redirected via link bucks when browsing the internet. It was odd when it happened on my nexus 7 tablet but also has started happened on the 2 laptops that are connected to my router.
There's no specific pattern, time or website but it is certainly happening on websites that wouldn't use link bucks (Facebook/university e-mail). I have security software installed on all devices (lookout on nexus 7, MSE on windows 7 laptops).
Any advice anyone could offer would be appreciated, its getting annoying now!
Thanks!
P.s. - at the same time my nexus 7 stopped connecting to Google now with a connection error, but only when connected to my network, on other networks it works fine

A:Linkbucks redirect across all devices connected to router

Welcome aboard  Try resetting your router.... Turn the computer off.On your router, you'll find a pinhole marked "Reset".Keep pushing the hole, using a pencil, or a paperclip until all lights briefly come off and on.NOTE. Simple router disconnecting from a power source will NOT do.Restart computer and check for redirections.NOTE. You may need to re-check your router security settings, as described HERE 

5 more replies
Answer Match 70.56%

-Here is my setup so far. I have a vista machine with 2 lan cards, one from motherboard, one on pci. The lan from motherboard is connected to the WAN port on my router. I have alltel wireless internet that uses ICS through that. The lan card on my pci bus is connected to a LAN port on the same router. When i am not using ics i disable the lan on my motherboard and vice versa. I am using the second LAN on my pci bus that is connected to one of the LAN ports on my router so my computer can use MCE and DIRECTV2PC. I have another line connected to a LAN port on the same router going to a switch which is connected to my 360 and my directv receiver.
-Here is the problem. Say im using DIRECTV2PC and the xbox gets turned on, what happens is i lose connection to my directv and my computer only sees the xbox and vice versa. I am confused on why that is, it should see both at the same time and not lose connection to any one of them right?
 

A:I lose connection to some devices on my switch connected to my router.

whoa man never heard of that kind of set up before. try connecting your internet to the WAN port on the router and connecting the rest of your stuff to the inputs on the router. its a little less complicated this way.
sounds like your computer is controlling your internet and getting confused... hope this info is usefull.
 

2 more replies
Answer Match 70.56%

I'm thinking of buying a wireless router for my son who has a laptop but he ALWAYS downloads huge files (games or whatever he does) when he uses my computer so is there a way to limit the bandwidth he gets when he connects to the router through his laptop?
 

A:Is it possible to limit the connection speed of devices connected to a router?

Look for a wireless router with traffic shaping and QoS. From my search, a Billion 7400 has traffic shaping. Also, the Actiontec MI424WR has it as well. Here's the shot from the Actiontec configuration pages.
 

1 more replies
Answer Match 68.46%

Slowly lost app's now have no control. Or admin privilege. The screen looks fake. There's drives listed I can't access. And every download was hijacked. Now theres no real Network or bios driver installed. after multiple attempts and no system functions available I want to use another computer and try to download virus software there. Noticed something strange happen and both laptops havea Dll bug long story short my Android, laptops, printer and router have all been hijacked and I do not know what to do at this point

I haven't seen or been able to find anything on something so expensive enedina have any other laptops that are accessible at this time so even doing it from my phone is challenging
 

More replies
Answer Match 66.36%

I have 7 devices connected to my Netgear Router 600/3700v2 and the devices keep disappearing. I believe I have found the solution. Connect to your Netgear Router (you will see BASIC and ADVANCED options) and select the ADVANCED settings. Click the tab below ADVANCED SETTINGS and in the drop down menu select UPnP. You will see on the top of the screen ADVERTISEMENT TIME TO LIVE - this setting DEFAULTS TO "4" which is okay for "normal" home use (well, it didn't work for me). This setting is what controls your attached devices. If you keep losing them, try increasing the settings until they remain visible. I tried 5 first - no go. Then I tried 8 and I haven't lost the devices since. Hope this works for you!
 

More replies
Answer Match 66.36%

Hi,

This is my first post so please be gentle, I have a Netgear DG834GT connected to Talk Talk with a WEP security key, I have 1 desktop, 1 laptop, ps3. ipod touch and iphone all using it wirelessy, there all connected to my home network, but its pot luck if you can connect to the internet at any time with any off them, it seems to be whatever is connected first is ok, whatever trys to connect to 2nd or 3rd and so on is pot luck, or the connection may even drop, please help.
 

A:Solved: Lose connection with netgear router, with multiple devices???

16 more replies
Answer Match 64.68%

As it says on the tin really! I am an absolute non technically minded person so have no idea how to even start trying to fix this problem. A few weeks ago our router quite happily let multiple devices attach wirelessly to the internet at once but in the last couple of weeks it has started only allowing one device at a time to connect to the internet. If say my partners work laptop is connected then our home laptop/iPad can see the wireless router but it will not allow them to connect to the internet anymore. Can anyone help me to try and sort this please...I can use my computer for basic things but am in no way technically minded so please be very clear and simple with any help you are able to give.

TIA
 

A:Unable to connect multiple devices to internet using Huawei EchoLife HG521 router?

10 more replies
Answer Match 62.58%

So... like most of world my family lives online. Having found that ISP pricing in Alaska is horrendously expensive, I want to find a solution that I can create 4 SSIDs, one for each of my three kids (ages 12, 14, &16) and one for me and my wife, and place a data cap on each SSID so that I can't be hit up with the bills that come with overages. I figure with individual SSIDs they can use what ever device they have with out having to detirmine MAC addresses or IPs used or any of that other stuff.

I would like to have just one router be able to accomplish this. I have an older router, an Apple Time Capsule I bought about 6 years ago, but as I don't use Macintosh computers any more, I would be happy to buy a new router and get it set up to manage this dilema.

Any Advice or suggestions will be greatly appreciated.

Thanks.
 

More replies
Answer Match 57.54%

Hi there

Not sure whats happening here but getting multiple displays for the same devices !!!!

Any fix, or is system Broken.



Cheers
jimbo

A:Devices and Printers - devices being displayed multiple times

Looks like Ghosts of DLNA devices. Start by taking offline any DLNA capable gear, reboot the Gateway and also clear its IP Table.

Also clear out those ghosts from Devices and Printers.

For some reason this started in Windows 7, when Microsoft started to play games with DLNA and media Shares.

1 more replies
Answer Match 55.44%

Okay I live in the dorms in college.(well actually they are not the dorms but overflow apartments because the dorms were full, not sure if it matters but thought i should add) I brought my wireless netgear router with me to school to plug my Ps3 into and to download certain things the school blocks on the regular wireless internet.

So I plug my router into the jack in the room and then run wireless to my laptop and wired to my Ps3. I set up the router and it determined the internet connection is DHCP . I set the router to obtain I.P. and DNS addresses dynamically and it won't work. then i set it to use static addresses. ( the address that it picked up dynamically ) It then works for awhile, sometimes a few hours and sometimes less than an hour. To get it to work again all I have to do is set it back to dynamic wait a couple minutes and move it back to static. When I lose connection my playstation says its a DNS error.

my roommate plugs his laptop directly into the jack on the wall because he doesn't have a wireless card and he hasn't said anything about losing his connection. But once i plugged him into the router he loses his connection just like me.



I am sure i am forgetting something important if anymore info is needed I will add. Please help it is really getting annoying changing the setting on the router
 

A:Connected but losing internet access on wireless router connected to dorm room

If you don't use the router at all, does your Internet connection stay active?
 

3 more replies
Answer Match 54.6%

I consider myself an advanced user, but this one I've never seen, nor can I find info out for...

I haven't been able to plug a video camera or external hard drive into my computer via FireWire. I then tried a different cable, nothing. I then tried a different device and cable, nothing. I then tried a different computer with two devices, nothing.

My USB2.0 works fine with each device and computer. I also took the new computer into CompUSA and they tried their firewire device and all worked. I bought a new firewire cable, but I have the same luck with each device.

How can 2 external hardrives, and one sony camera not work, after working for a year. What happened? What do I need to do?
 

A:Multiple firewire devices on multiple computers not working

6 more replies
Answer Match 53.76%

I have an HP Windows Vista Computer and just bought the verizon jetpack: wireless internet that you can connect your devices to. My computer connects to the jetpack but not to the internet. I talked to a verizon tech guy and he said that data is going through from the jetpack to the computer but no data is being sent out. He said it could be a firewall or something that is preventing it but I don't know my way around computers enough to find what could be stopping it. Please help!
 

A:Desktop is connected to internet and data is coming in but no data is going through

16 more replies
Answer Match 53.76%

Hi,

I'm sure this question has been asked multiple times because I myself have read countless posts trying to figure out my problem and solve it, but nothing has seemed to work for me. I have an HP G60-230US laptop and a Linksys router. It says my laptop is connected to linksys but it has a limited connection. It will not connect to the Internet and I can't open the Internet at all. I got an error saying that it was unable to communicate with the Primary DNS Server but I'm pretty clueless as to how to go about fixing this.

Thanks in advance!
 

A:Laptop is connected to router, but is not connected to Internet.

12 more replies
Answer Match 53.34%

There are multiple websites that I cannot connect to, facebook, rottentomatoes, youtube, to name a few. Others seem perfectly fine. A few seem okay, but seem to be running slowly.

This is the case for both my computer (on which I am running Windows 7), which is connected directly to the router, *and* mobile devices which are connected wirelessly.

On my computer I have tried using several different browsers to no avail, but when I used the TOR browser to proxy, I was able to access them.

I apologize if this has been asked, but I haven't been able to find anything this specific.

Thank you.
 

A:Can't connect to multiple websites on multiple devices

6 more replies
Answer Match 52.92%

Hi, I bought a data sim using it on my nokia 5220 mobile.
The internet worked for the first week and it worked good, but then while connected after a while the internet will stop working and the same thing happens with my dial up 56kb land lind connection.
So i reinstalled windows the computer thinking that was the problem, it helped with the dial up connection stop working after a while. With my Nokia it is connected to the pc but no web browser is working or online game or messenger. Please i need help with this, thanks
 

A:Mobile data sim connected but no internet or data

I set the DNS ports manually and that fixed the problem. But not the internet is connected and sometimes it stop working and starts back after a while please help
 

1 more replies
Answer Match 52.5%

Hi to all seven forums..!
when I connected more then 3 usb device in my pc, the 4th usb device not working,,
my pc all usb port is worked and my usb device is also, but not working together four usb devices.. only 3 usb devices work at a time..
what is the solution for this...?

Regards:.

A:USB devices not connected more then 3.

Depending to what you plug into the USB hubs, you may be out of power to allocate to the 4th hub

7 more replies
Answer Match 52.5%

Hi there

I see BELARC advisor manages to do a security audit of USB devices attached to a computer. Since this must obviously be stored on Windows somewhere does anybody have any idea how to extract this information easily.

I could then run a script every so often as say a nightly job for audit purposes.

Any help here

Cheers
jimbo

More replies
Answer Match 52.5%

How many USB devices can I have connected?

OK: sounds like a dumb question.
Everyone shopuld know that you can have upto 128 devices all conncted by USB - right...?

I use USB extension wires: these seem to cause problems.

If I want to extend the lenght... should I simply connect several USB hubs?

Are USB extentions known to cause problems?

If I have 5 USB hubs connected all of of each other: will I have problems when I connect a device to the last one?

Thanks.
OM
 

A:How many USB devices can I have connected?

I think the main two considerations are power and traffic.

Clearly, power hungry devices will require at least some powered USB hubs.

The more traffic (e.g., networking means lots of traffic), the more likelihood for clashes and slowdowns.

I'm pretty sure there are maximum recommended distances for USB, but I do not have such info handy.
 

2 more replies
Answer Match 52.5%

Hey yall
Am having an issue after resetting my router. My computer connects to my router and the signal is fine but the router does not seem to be connected to the internet!!! am a web researcher and i use my internet everyday and I would really appreciate if you guys could help me out!

Here is the ipconfig message http:Microsoft Windows [Version 6.0.6000]
Copyright (c) 2006 Microsoft Corporation. All rights reserved.

C:\Users\Mike>ipconfig/all

Windows IP Configuration

Host Name . . . . . . . . . . . . : Mike-PC
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No

Ethernet adapter Local Area Connection 2:

Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Motorola SURFboard 4100 USB Cable Modem
Physical Address. . . . . . . . . : 00-20-40-A5-EC-AF
DHCP Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
Link-local IPv6 Address . . . . . : fe80::4501:c400:7231:c124%12(Preferred)
IPv4 Address. . . . . . . . . . . : 24.201.16.177(Preferred)
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Lease Obtained. . . . . . . . . . : August-22-07 11:30:36 AM
Lease Expires . . . . . . . . . . : August-23-07 5:43:13 AM
Default Gateway . . . . . . . . . : 24.201.16.1
DHCP Server . . . . . . . . . . . : 24.200.242.21
DHCPv6 IAID . . . . . . . . . . . : 301998144
DNS Servers . . . . . . . . . . . : 24.200.241.37
24.201.245.77
24.200.243.1... Read more

A:Solved: My computer connects to my router but my router is not connected to internet

16 more replies
Answer Match 52.08%

I want devices connected to the router to be able to connect to the modem.

My ISP modem says:
Local IP address 192.168.1.1
Subnet mask 255.255.255.0
DHCP Server: Enabled
Connection mode: DHCP
Starting IP address: 192.168.1.10
Ending IP address: 192.168.1.128
Connected devices: Eth-Switch LAN (2) 192.168.1.12 Netgear WNDR4000 Router

My Router says:
Router Information
IP address 10.0.0.1
DHCP: On

Internet Port
IP address: 192.168.1.12
connection DHCP
IP subnet mask: 255.255.255.0
Gateway IP address: 192.168.1.1
RIP Direction: Both
RIP Version: Diabled
Attached devices: 10.0.0.4 HP computer
Use Router as a DHCP Server:yes
Starting IP address: 10.0.0.2
Ending IP address: 10.0.0.254

So how would I modify the settings so the HP computer (10.0.0.4) could see the modem (192.168.1.1)?

Answer for dummies please!
 

A:What are the correct settings for a Router connected to an ISP Router/Modem box.

Let's be clear: you have

Code:

isp==modem at (192.168.1.1)
|
+--- (192.168.1.12) router (10.0.0.1) - - - hp pc (10.0.0.4)

what happens if the HP does ping 192.168.1.1 ?
 

1 more replies
Answer Match 52.08%

I have HP G60 laptop but suddnely last 3 to 4 days my nereast router-5 stop connected to my Laptop

I have 5 router

Router 1
Router 2
Router 3
Router 4
Router 5

Router 5 is near to me. There are low signal to Router 1 to 4 so i always connected with Router 5 but last few days my laptop not connected with router 5 and it showa only local area connected

Plese help me if some one know about it?
 

A:Solved: Out of 5 router my nearest router not connected to my Laptop

Windows IP Configuration

Host Name . . . . . . . . . . . . : Devdatt-PC
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
DNS Suffix Search List. . . . . . : guestnetinc.com

Wireless LAN adapter Wireless Network Connection:

Connection-specific DNS Suffix . : guestnetinc.com
Description . . . . . . . . . . . : Atheros AR5009 802.11a/g/n WiFi Adapter
Physical Address. . . . . . . . . : 00-23-4E-47-3A-30
DHCP Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
Link-local IPv6 Address . . . . . : fe80::24c4:c522:2b60:a90f%11(Preferred)
IPv4 Address. . . . . . . . . . . : 10.0.0.174(Preferred)
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Lease Obtained. . . . . . . . . . : Sunday, December 02, 2012 8:54:42 AM
Lease Expires . . . . . . . . . . : Sunday, December 02, 2012 11:54:42 AM
Default Gateway . . . . . . . . . : 10.0.0.1
DHCP Server . . . . . . . . . . . : 10.0.0.1
DHCPv6 IAID . . . . . . . . . . . : 234890062
DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-17-C4-BB-D3-00-23-4E-47-3A-30
DNS Servers . . . . . . . . . . . : 10.0.0.1
NetBIOS over Tcpip. . . . . . . . : Enabled

Ethernet adapter Local Area Connection:

Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Realtek RTL8102E/8103E Family PCI-E FE NIC
Physical Address. . . . . . . . . : 00-1F-16-54-AE-F3
DHC... Read more

3 more replies
Answer Match 52.08%

OK this is complicated so bear with me!

First time poster as well so please be gentle!

I have Telewest Cable Broadband working with a Linksys wireless G (wrt54g) router. It works a treat and i have the "improved" antennae from Linksys to boost the signal a bit as well.

I recently signed up with Vonage for a VoIP provider and the router they provide is wired (the Linksys rt41p2 router) and im trying to get this connected to my wireless network with a seperate Gateway or wireless hub. Im pretty sure this will work if i put the access point in infrasturcture mode (im thinking the linksys WAP54G access point) and conenct the VoIP router to the Access point (with DHCP disabled so its technically a switch) and then it can pick up the signal from the router over a wireless network.

The router seems to support this as it has a VoIP over wireless option in the setup of the latest BIOS flash.

What i need to know is if anyone here has a setup like this and any problems they have with this type of setup! Any help wopuld be much appreciated.
 

A:VoIP router connected with Wireless Gateway and Router HELP!

I'm thinking the VOIP should go first
then just set up as you would 1st one router 2nd one gateway.
 

2 more replies
Answer Match 52.08%

I have Linksys wireless router, and I've been using that for awhile, no problems with it.

I had a 50 foot CAT5 cable sitting around and as well, an old D-Link DI-604 wired router, so I decided to turn the router, into a switch so can I hardwire my Desktop and PS3.

I have the Port 2 Linksys router outputting the internet to the WAN D-Link wired router using the 50 foot cable, and then using Port 1 and 2 to my Desktop and PS3, respectively.

Everything on the Desktop and PS3 side seems to be great, i've noticed web pages loading times decrease.

Except that the computer which is hardwired to my Linksys wireless router, is awfully snail slow.

Is it because the D-Link router is a Router and not a switch, that this problem is happening?

Edit - I've been reading that this is more complicated then a simple plug and go. I have to disable the DHCP and everything, everytime I try to log into my D-Link router, it'll get into the routers main page, but nothing will load after I try to click 'LAN' or 'WAN' or 'DHCP'

Edit 2 - Alright, so I have changed my 2nd router to disable the DHCP and changed the IP to be different from my 1st router, and everything seems good except for one thing. When I plug in my PS3 to either Port 3 or Port 4, the whole network is crippled, and nothing connects. Very interesting. I'm going to replace the CAT6 cable from my PS3 to my router-switch with a crossover cable, i've got a feeling it's ... Read more

A:Solved: Router connected to another router, slower internet

I guess so.
 

1 more replies
Answer Match 52.08%

I am finding error 50 while using dial uo modem that all devices connected pl do guide

More replies
Answer Match 52.08%

I am on a wireless network, I am not in charge of the router that belongs to somebody else but i connect to the network with a usb. I was wondering if there is a way to see how many people are connected to the network? I am using a belkin usb the software that comes with it just shows you the name of the network and the signal strength.
 

A:How to see how many devices connected to network?

You can run something like SuperScan to scan the entire subnet, that will identify all the machines on that subnet.
 

2 more replies
Answer Match 52.08%

Hey there. is there any software to check how many devices are connect to my router? I remember there was a small application for xp i use 1year before but i lost it now. How to check how many devices connected to a router other than router panel menu or net check command in cmd. please help.

A:How to check how many devices connected?

Well if your router is acting as a DHCP server, giving out IP addresses, like most home routers do. You should be able to go into your router configuration (usually through a browser window) and see who has IP addresses leased out.

1 more replies
Answer Match 52.08%

Hi, I hope someone else has had this problem and can help.

I bought a new MP3/4 for my son. Manual states it's configured for WMP 11.
Tried to synch to load music but WMP says 'connect device'. MP3 already connected but WMP only sees the cd/dvd drive.

Tried 2 other MP3's with the same result, nothing.

Checked MP3 with another computer and it worked fine.

I'm sure there's a simple solution, I really don't want to reinstall Vist, but there seems no way to reinstall WMP on its own.

More replies
Answer Match 52.08%

Does anyone use the devices in uTorrent? I have this random Samsung Galaxy S3 showing as disconnected under the device section, which says drag torrents into devices to initiate media conversations, but I have never plugged it onto my computer. I do not uTorrent remote access enabled, and nothing is showing up on the paired device section in the preferences menu. I personally do not use an S3, but I have a family member that does and it connects to the same wifi network. Is it showing up only because it works on the same wifi? Or should I be concerned?

A:uTorrent connected devices?

Hi AnthonyY From my experience with uTorrent, if you ever had a device connected to your computer or on the same WiFi network as you that used uTorrent in the past on it, it would be detected by your desktop application of uTorrent and show under "Devices". If you right-click on it, you'll have the option to "Remove device" if you want to get rid of it.

5 more replies
Answer Match 51.66%

Our ISP recently updated their hard ware to work with the Sprint network. Note: our ISP is not Sprint, but the local phone company.

Our Hardware:
Internet: DSL 10.0 (highest speed available)
Modem: Comtrend (ISP provides)
Router: Belkin N
Computer: 10 yr old Dell running XP - service pac3 - wired connection
Kindle Fire (first edition, no HD, etc) - wireless connection
Xbox 360 - wireless connection

Issues:
Xbox - went from constantly bumped from Xbox Live game by losing internet connection to not being able to enter a game at all
Kindle - went from occasional "network error' message during online tasks to having to restart download (multiple times) or refresh page for most any or all online tasks
Computer - have to click refresh to get most any page to load after the home page

What we've tried so far:
I have recently cleared the cache on both the computer and Kindle. XBox's new security measures have been met.

My questions:
Do any or all of these issues seem to be related?
Is there a piece of equipment or something we may be missing to make all of these things work? I am a networking novice.
Who should I call to get these issues corrected, my ISP or a tech service? Note: if I start with the ISP and they do not find an issue I have to pay for the call.
 

A:Multiple issues over multiple devices

First. You should try to NOT use a wireless connection for any type of gaming: PC, Mac, Console, etc. If you can hard wire the xbox you'll be waaay better off than using wireless.

Now... Yes, the issues could be related - there maybe an issue with the Belkin N router. I'd try to first reset the Belkin router to default settings, check on manufacturer website for instructions how, most routers you can press a "reset" button w/ a paperclip or ball point pen. Reconfigure the Belkin router, recreate the wireless network and see how everything works. If you are still having issues, humor me and connect the Dell directly to the DSL modem, bypassing Belkin router. See if you still have connection issues, if you do then it could be the DSL modem that is the problem and call your ISP to replace. If you don't have same issues then it's most likely an issue with the Belkin router. Replace it. Don't buy the dirt cheapest router at the store, but you most likely don't need the most expensive one either. Find a good middle ground router, ask sales associate to assist you accordingly.

Post back, Hope this helps!!
 

1 more replies
Answer Match 51.24%

Basically I have a situation where users are creating data tables in Microsoft Word using the creating table functionality, and are then resquesting that the data will be imported into a single Microsoft Database field.

Please could someone show me the best way of doing this!!!!!!

Cheers !!!
 

A:Importing Table Data Into Multiple Access Field Data?

Do you mean they're creating, say, a 3-row by 3-column table and then they want to import everything in that one table into a single field? a single record?

Out of curiosity, what happens if you copy and paste, perhaps with an intermediate step through Excel?

Also, is there a reason why your users cannot work directly in Access?

More details, please.
 

3 more replies
Answer Match 51.24%

I have a Lenovo ThinkPad Helix (not sure of the exact model number but it's an i7 with 8GB ram and 128 GB SSD). After I upgraded to 8.1, I was able to pair the laptop to my bluetooth speakers and my phone (Motorola Razr Maxx) but almost instantaneously after connecting both my speakers and phone would drop and say not connected.

Nothing I did would resolve the problem, and I have gone through more or less every thread on this board relating to bluetooth issues. I've tried reinstalling the drivers, I've set the bluetooth support services to start automatically but the only thing to get bluetooth working again was to roll back to Windows 8.

So my question is this:

I kind of miss some of the features of 8.1 and I'd like to get those back, but not at the cost of bluetooth functionality. Is there any way to get the bluetooth working in 8.1, or any way to get the features of 8.1 in 8?

Some extra information; I'm running Windows 8 64 bit Pro as of right now and bluetooth is working fine; I have a broadcom bluetooth radio that came preinstalled in my laptop, specific model number is BCM20702A0;While I was using 8.1 there were no issues in Device Manager regarding drivers, at least not with the exclamation marks nor any unidentified devices.

A:Bluetooth devices would not stay connected in 8.1

Okay, the problem seems to have automagically fixed itself. All I did was revert back to windows 8, like I said in the previous post, and after updating to 8.1 again the problem does not exist anymore. I have no explanation for what's different or why it worked but I'm not going to question it.

1 more replies
Answer Match 51.24%

Hi Folks,
This is my first post and I hope you can help me.
I have recently had my ADSL main socket moved which has resulted in me using a Netgear FS608 v3 Switch to link my PS3, Vista x64 and XP PC's to the router. I also have 3 Laptops connected to the Linksys Wireless router. All machines can connect to the internet. The printer is connected via USB to the Vista x64 PC and I can print from a Laptop only if I try to "add a printer" it doesn't find one but it does print whats in the queue!
The main problem is I can't see any of my device when I look at the network, any help would be most welcome.
Peter

A:Networking Switch can't see connected devices

Originally Posted by PeterGP


Hi Folks,
This is my first post and I hope you can help me.
I have recently had my ADSL main socket moved which has resulted in me using a Netgear FS608 v3 Switch to link my PS3, Vista x64 and XP PC's to the router. I also have 3 Laptops connected to the Linksys Wireless router. All machines can connect to the internet. The printer is connected via USB to the Vista x64 PC and I can print from a Laptop only if I try to "add a printer" it doesn't find one but it does print whats in the queue!
The main problem is I can't see any of my device when I look at the network, any help would be most welcome.
Peter



Peter

Hi and welcome

Its a little hard to visualize. could you either explain whats where or draw us a simple pic

Ken

3 more replies
Answer Match 51.24%

Hello,

I would like to know if a Wi-fi interface, 802.11, when for example is connected to a router is listening also to the messages coming from others routers and equipments. Is it listening to every coming messages and then discard it? is the collision mechanism then affected also by equipments not included in the WLAN?

Thanks.
 

A:Is it a 802.11 interface listening also to not connected devices?

Is it listening to every coming messages and then discard it?Click to expand...

Yes; it has to look at the header to see if the message is meant for it.

is the collision mechanism then affected also by equipments not included in the WLAN?Click to expand...

Not sure just what you mean by the question. If you are asking whether wireless interference (signals on the same or close channel) can look like valid messages and thus cause a real message to look like a collision I think that the answer is 'yes.'
 

1 more replies
Answer Match 51.24%

Hi, I'm using the HP Cloud Recovery Download Tool to obtain Windows 7 for a new notebook that comes with Windows 10 pre-installed. When I get to the 'USB Preparation Page' to select a USB drive it shows "No USB devices connected" even though there is a USB drive connected and recognised by Windows. I've tried this with two USB drives, one 160GB and one 2TB, with neither being recognised. The drives have some data on them but I assume that they do not need to be formatted beforehand as it looks like that happens as part of this recovery process. I've tried restarting etc but have had no joy so far and would be grateful for any tips that may help.

More replies
Answer Match 51.24%

Hi everybody,

Got a bit of a strange issue that I couldn't find any answers for online or here, but if it has already been asked, then a link would be great! Thanks in advance

Here's the issue:

The USB device (mouse, HDD, whatever) works fine. I disconnect it for whatever reason, but when I do, the device can still be seen as connected (i.e. HDD file folder structure shows up, but when I click into a folder, it says that's empty when it in fact it isn't, Logitech mouse still shows up in button programming software, Logitech Gaming Software). Then when I try to connect the USB device, I cannot use the device. Power through the USB ports still works it seems, at least when I use it to charge my phone anyways.

I have updated all of my USB drivers to the newest edition available on my manufacturer's website (http://www.asus.com/Notebooks_Ultrabooks/N56VM/#support).

Here are my specs
Asus R501V (AU/NZ equivalent to worldwide N56VM)
i7 3610QM
8GB RAM
64-bit Windows 7 Home Premium SP1

Anybody have any suggestions?
 

More replies
Answer Match 51.24%

Hi everybody,

Got a bit of a strange issue that I couldn't find any answers for online or here, but if it has already been asked, then a link would be great! Thanks in advance

Here's the issue:

The USB device (mouse, HDD, whatever) works fine. I disconnect it for whatever reason, but when I do, the device can still be seen as connected (i.e. HDD file folder structure shows up, but when I click into a folder, it says that's empty when it in fact it isn't, Logitech mouse still shows up in button programming software, Logitech Gaming Software). Then when I try to connect the USB device, I cannot use the device. Power through the USB ports still works it seems, at least when I use it to charge my phone anyways.

I have updated all of my USB drivers to the newest edition available on my manufacturer's website (N56VM - Notebooks & Ultrabooks - ASUS).

Here are my specs
Asus R501V (AU/NZ equivalent to worldwide N56VM)
i7 3610QM
8GB RAM
64-bit Windows 7 Home Premium SP1

Anybody have any suggestions?

A:USB devices showing up as connected after disconnecting

Hi and welcome to TSF this might be of help but I cannot promise a definite fix USB Driver Reset and USB Ports Power State Reset - Sysnative Forums but I have seen it used with good outcomes many times

1 more replies
Answer Match 51.24%

Namely my Computer (the one I am currently on) and my PS3. Here is the setup for both:

Windows XP (Yes, it's ancient) has some sort of Netgear USB drive that detects a network (or something like that) and that is connected to my Linksys router, which is connected to a computer in my Dad's room and an Arris Modem with Time Warner Cable as the provider. In order to repair the connection after it drops me (usually it doesn't say it drops me, but my internet won't open or display any pages) I right click the icon at the bottom right and click repair. That will do it until the next time it messes up, which is usually about a half hour or an hour or so. Already Power Cycled everything and I have tried resetting the router numerous times. Anything else you wish to know advise me of what you wish to know and how I can go about obtaining the desired information.

The PS3 is connected wirelessly and has flawless online while I am signed on. Randomly though, it will sign me out of the PSN (Playstation Network) and I will have to sign back in. This prevents me from doing serious online matches, as I will get booted out the moment I get signed out of the PSN. I am assuming it has to do with the network connection in general, because my computer disconnects usually at the same time.

Any insight on this matter would be appreciated. I love learning new things about computer, as one day I wish to be a tech guru of some sorts, so feel free to teach me other things as well... Read more

A:Network is Dropping Devices connected to it

12 more replies
Answer Match 51.24%

Hey guys, so today I update my system and surprisingly, I can't see my connected devices (such as mobile phone, external hard disks, etc) under 'This PC' or elsewhere. Tried uninstalling the drivers through Device Manager, restarting, everything.. but doesn't work. And no, it's not a problem with the usb ports. I can hear the sound of the devices connecting and I can charge them, but that's all... Don't know how to access them

More replies
Answer Match 51.24%

I need to know all the IP addresses of all the the laptops connected to my LAN.
I've done the ipconfig command but this doesn't give me the information I need.
Can anyone offer any help asap please. Much appreciated!
 

A:Need to find out all the IP addresses of devices connected to my LAN

is this a home network - if so have a look in the router - it should have an dhcp table - but note the IP can change each time the laptops connect to the router
 

1 more replies
Answer Match 51.24%

My laptop says connected to intranet not Internet? Seems like this is I big issue but what's the definite answer.Please please help me. Thanks in advance and I wish you all the luck in the world. I need my laptop online (well on the Internet) so bad.

A:Why do all my devices 3 connect but my laptop says connected

1) Tools -> Internet Options2) Connections tab3) LAN Settings4) Uncheck "Automatically Detect Settings"

3 more replies
Answer Match 51.24%

From the start, my XP Home recognized every DV device I hooked up: VCRs, 3 different cameras, and a digital video editing machine. Now, after installing SP2, it doesn't see any of them. I've tried new cables ... still nothin'.

I really need to feed my computer its video rations, so please help!
 

More replies
Answer Match 51.24%

My computer locks up anytime that I connect it with a USB port. I've had an ipod for a while, and it's locked up all along, but I've just dealt with it. Recently I bought a new digital camera, and an external hard drive, and it does the same thing. It doesn't lock up right away, it takes about 10 minutes after its connected. Any help would be appreciated. I'm a bit computer stupid, so keep that in mind.
 

A:Computer locks when USB devices are connected

15 more replies
Answer Match 51.24%

Hello

I've had a problem with my bluetooth keyboard and mouse for quite some time now. The problem is that they disconnect and then won't reconnect. This usually happens after the computer has been inactive for about an hour or so, but it varies. Occasionally they have disconnected while I've been using them, but this is a rare occurence.

The problem comes when I try to use the mouse after it has been idle for a while. Usually clicking the left mouse button brings it out of sleep mode and the light comes on at the bottom, but in the occasions where it does not work nothing happens. The computer for some reason still considers it to be connected; I have a program called BluetoothView which shows the last time connected, and this is continuously updated even when I can no longer use the mouse.

I'm running Windows XP SP2. My bluetooth adapter, as well as the keyboard and mouse, are all manufactured by Belkin.

Any help greatly appreciated

Thanks in advance!
 

A:Bluetooth Devices Supposedly Connected But Not

Is your PC going into power saving mode? That can cause this type of issue.
 

3 more replies
Answer Match 51.24%

I've got a D Link Modem up and Running.. Now, I Figured out that someone used my WLAN. Is there a way to View the Visitors to my WiFi? Password Protected Device.
Thank You in Advance..

Some Details..
Device Info

BoardID:
DSL-2730U

Software Version:
IN_1.00

Bootloader (CFE) Version:
1.0.37-106.5

DSL PHY and Driver Version:
A2pD033c.d23e

Wireless Driver Version:
5.60.120.3.cpe4.406.0

This information reflects the current status of your WAN connection.
Line Rate - Upstream (Kbps):
838

Line Rate - Downstream (Kbps):
1999

LAN IPv4 Address:
192.168.1.1

MAC Address:
1c:7e:e5:f0:6e:3b

Default Gateway:
ppp0

Primary DNS Server:
218.248.245.1

Secondary DNS Server:
218.248.255.139

LAN IPv6 Address:
Default IPv6 Gateway:

A:Need List of Recently Connected Devices.

This is not really a win 8 issue, you might have more luck contacting d-link support directly and asking them here.

I was also worried that someone was using my wifi a while ago, I found out who the culprit was by looking at the list of reserved IP addresses. Most routers have this facility. Usually the lease time is a couple of days so you can see everyone whose connected in the last two days. You can then either block that mac address or change your password. I blocked it and found out it was my flatmates new phone! Oops!

Good luck!

9 more replies
Answer Match 51.24%

Every time I try to connect my phone by USB it will make the noise like it connected but then disconnect and continue to make the noise. Though the phone is charging but not showing up in File Browser under devices. The same thing happens to my GPS when I am trying to connect it in order to update it. This is getting very frustrating. The only thing that shows up is my Flash Drive. It didn't always do this but now I can't plug in any devices to try and update them or add things to them. Please help!

A:Devices won't stay connected to laptop

Hi Freakstormer3
Thanks for writing to  us. 
When did the issue start? Have you made any hardware or software changes lately?
Please update the USB drivers from support.euro.dell.com-enter tag#-submit-drivers and downloads--chose the operating system and install the chipset drivers. 
Does it happens with all USB port?
Let us know how it goes. 
If all the devices are disconnecting randomly still , please format the machine post backing up the data. If  still the same, then its a hardware failure.
Regards

4 more replies
Answer Match 51.24%

I'm wondering if there is a way to show the connected devices as icons on the desktop as is done in OS X. If you aren't sure of what I'm talking about, it's when I plug my phone, external hard drive, DVD, etc into the computer and instead of always going into My Computer to view what's connected, it shows up as an icon on the desktop. Is this possible, or is this just a feature I have to live without unless I cross over to the dark side and use OS X?

A:Is it possible to have desktop icons for connected devices

Hello xanpolak, and welcome to Seven Forums.

You should be able to right click on the device in the "Computer" window, then click on Create shortcut to have a shortcut created on your desktop for a desktop icon.

Hope this helps,
Shawn

4 more replies
Answer Match 51.24%

I have Vista Home Premium SP1.

When I connect some devices like an iPhone or a Digital Camera, it doesn't show up as a drive in Explorer.

When I open Device Management, the errant device appears under "Portable Devices", with an error icon, and shows the following message in its properties:

"Windows cannot start this hardware device because its configuration information (in the registry) is incomplete or damaged. (Code 19)"

Other devices like an external hard disk don't show any errors and also show up as drive letters.

Can anyone help?
Thanks in advance.
 

More replies
Answer Match 51.24%

I have a dell laptop that has 1920x1080 resolution. However, i connect it to an external monitor that has 1920x1200 resolution. Basically almost everything i do is on my external monitor which acts as my main primary screen. Thus i do sometimes open some windows or drag a window or so to the other screen like youtube etc to the laptop screen which is the secondary monitor.


My issue at the moment is everything is way too big on the laptop screen. I want to have 1920x1080 resolution but its way too big. I googled what is my resolution on it and it shows 1536 x 864. Can someone tell me how to change this to 1920x1080? I googled what is my resolution on the external monitor and it does show 1920x1200 which is correct.


My external monitor which is my main monitor is fine at the moment with the 1920x1200. Its windows 10 but im assuming this should be very similar to windows 7 to fix this issue?

More replies
Answer Match 51.24%

I have a dell laptop that has 1920x1080 resolution. However, i connect it to an external monitor that has 1920x1200 resolution. Basically almost everything i do is on my external monitor which acts as my main primary screen. Thus i do sometimes open some windows or drag a window or so to the other screen like youtube etc to the laptop screen which is the secondary monitor.


My issue at the moment is everything is way too big on the laptop screen. I want to have 1920x1080 resolution but its way too big. I googled what is my resolution on it and it shows 1536 x 864. Can someone tell me how to change this to 1920x1080? I googled what is my resolution on the external monitor and it does show 1920x1200 which is correct.


My external monitor which is my main monitor is fine at the moment with the 1920x1200. Its windows 10 but im assuming this should be very similar to windows 7 to fix this issue?

More replies
Answer Match 50.82%

the Cable connected to the modem, modem conencts to the Wireless router, and that connects to my computer. Since i hardly ever use the wireless router, i decided i want to just connect to the modem. I switched all the ethernet cords and by looking at what i had done, everything should have been working fine.

But that is wrong... I couldnt connect to the internet. I while back i set up a static IP address, but i changed that. the settings look like this now:
(to post this i had to go back to the router and the modem)

when i was trying to use just the modem, windows window bubble came up and said i have little or no activity, and i tried repairing it. windows tried to renew my IP address but that failed so there was nothing else i could think of doing.

what can i do so i can just connect throught the modem?!
 

A:Im connected through a wireless router and a modem... Want to get rid of the router

10 more replies
Answer Match 50.82%

I need to use several USB devices in the XP emulator but each time you restart the emulator it disconnects all USB devices, but the programs I have in startup in the emulator require that the USB devices be connected at startup. This means each time I open it I need to close every exe that expects the USB devices to be there, then virtually reconnect the USB devices and then re open the exe files.

This is a real PITA to do every single time I start the emulator, is there not an option to have specified USB devices remain connected to the emulator at all times?

Thank you

More replies
Answer Match 50.82%

Hi 
I don't know whether my question is right or wrong. 
  I have 2 Ethernet Port on my Embedded computer .I am using one is for Intranet connected device and another one is for internet.
I have connected some device to Intranet LAN Port..
Is there any chances for remote access the Intranet connected device like RFID reader and other devices.

More replies
Answer Match 50.82%

Setting up a hotspot on my asus laptop running windows 10 ,doesn't give the connected devices internet connection.I've tried netsh int ip reset,but with no results.All the drivers are updated.The windows mobile hotspot function says "We can't set up a hotspot because your PC doesn't have an Ethernet,wifi or cellular data connection." Here is an album with pictures that might help. http://imgur.com/a/sVqgp Thank you.

A:Wi-fi hotspot gives no internet connection to connected devices

Hello alligatorcampus, and welcome to Ten Forums.

You might see if using the method in the tutorial below to setup a mobile hotspot may work better for you.

Mobile Hotspot - Turn On or Off on Windows 10 PC

0 more replies
Answer Match 50.82%

Hi,

I am creating Wifi Hotspot in Windows 8.1 using the following command:


Code:
netsh wlan set hostednetwork mode=allow ssid=MyHotspot key=mywifikey


Then I start the hosted network. After starting the hostednetwork, I enable Internet Connection Sharing on my Huawei E397bu-502 device (4G LTE USB Dongle) in Network Connections. I can successfully connected my Android KitKat device to the hotspot and have internet connectivity on my Android.

But the problem is that the Android Phone disconnects randomly. Then I need to run


Code:
netsh wlan stop hostednetwork



Code:
netsh wlan start hostednetwork


After this I can again connect my Android to hotspot. But the process of disconnection continues.

Same happens if I share my Huawei-E397 internet connection via USB to my Android. There are no logs available so i have no idea where is the problem.

A:Win 8.1 Wifi Hotspot Disconnects Connected Devices

Welcome to the forum!

I thought you deserved some kind of reply by now although it is no help. These hotspot setups are so unique to what each person is trying to do I pretty much have given up trying to help online. So many variables. I hope someone can jump in and give you some guidance.

Would say to check all adapters and computer settings to make sure nothing is set to sleep or power save.

5 more replies
Answer Match 50.82%

I'm sure this is a simple thing but for some reason I'm having problems. I have two computers--one, a laptop using Vista, connects wirelessly to my Vonage VOIP router through a Trendnet TEW-637 access point and the other, a desktop using XP Pro is wired directly to the Vonage router. My Motorola Surfboard router feeds the Vonage router.

I need a program that will tell me the IP addresses of all these attached devices and identify them automatically. Running the ipconfig/all command is only giving me information about the box itself. Is there anything out there that will do this?
 

A:Determining the IP addresses of all connected devices on my network...

16 more replies
Answer Match 50.82%

Yesterday I had someone take a look at my computer to see why it was making a buzzing noise. It was dirty, and then it was cleaned. However, now the computer sometimes shuts off if something is plugged or unplugged, such as a mouse, keyboard, speakers, etc. What's wrong and how would it be fixed?
 

A:My computer shuts off when devices are connected/unconnected.

You need to post your system component specs. Motherboard; EXACT make, model and revision (if applicable). Processor; EXACT make, model and stepping. Memory; EXACT make and model. Graphics Card (if installed); EXACT make and model. Power Supply; EXACT make and model. Provide links to the components.

If the machine is a mass produced machine such as Dell, Gateway, HP, etc. post the EXACT make and model as there may be known problems with certain makes and models.

No one can diagnose a problem without knowing the EXACT components you used in the build or the EXACT make and model of a mass produced machine.
 

3 more replies
Answer Match 50.82%

Hi i'm not sure if this is the right place for posting this question basically I am trying to setup VPN on a Widows 2000 Server - I have enabled VPN via Routing and Remote access and enabled a test account with permission to dial in and have enabled port forwarding for the VPN port 1723 – When I try to dial in from the outside it connects via VPN fine but I am only able to ping the VPN server if I try to ping for example the router's IP it times out –

The server only has one network card installed do i need to fit an additional network card in the server.

I hope someone can help - thanks in advance
 

A:VPN 2000 Unable to access other devices once connected

You need to configure the VPN client not to use the default gateway on remote computer.

Other than trying to ping the router, can you connect to other devices or map drives to the VPN server?
 

3 more replies
Answer Match 50.82%

I currently have a Cisco 4507 running IOS Software ver. 12.2 EWA4.
Is there a command that would show me information on what device is connected to a specific port? (ie. IP address, host name, mac address, etc.)
 

A:Show connected devices on Cisco 4507

show ip int brief
show interface description
show mac-address-table
show cdp neighbors

You won't see hostnames unless they're running CDP, or somebody has labeled the interface.
 

2 more replies
Answer Match 50.82%

It started happening back in around November, my sister and my computer would start freezing occasionally, slurring the audio into a robotic sound, eventually to come to.

It gradually got worse, and I assumed it was a graphics card problem since it would freeze ONLY SOMETIMES and say that the graphics driver stopped working and has recovered. It usually didn't say that, though.

Lately though, I noticed that when it would freeze sometimes the internet would go out for some connected devices, such as the Xbox 360. The only computer that was NEVER affected by this is the one connected directly by Ethernet to the Netgear router, (every other device is WiFi.)

Sometimes even, my sister and mine would freeze simultaneously. It was a sort of rare occurrence, though.

I very lately started to notice that it would freeze when trying to load internet components with larger amounts of data, such as server console logs, Flash videos, and Soundcloud players. What threw me off is that it would sometimes freeze in programs like FL Studio or Windows Media Player... It's possible I guess that the programs were unrelated and what caused the freeze is SOMETHING sending/receiving corrupt packets.

I also noticed that sometimes my WiFi adapter stops functioning, although it says it works fine. I have to reset the adapter to get it to work.

I have done many virus scans since it's started and it doesn't fix anything. I've updated every type of driver, tried going low on ... Read more

A:Computer and all connected LAN devices freeze similtaneously

8 more replies
Answer Match 50.82%

Good Morning

I wanted to use the function of stand by of the PC.
I wanted also that the peripheral ones were extinguished once in stand by.

Once set up this function the PC goes regularly in stand by but the peripheral ones connected through usb remain ignited, additional masterize type, a peripheral one usb wi.fi, etc

Someone has said to me that perhaps some functions in the Bios are not set up in order to make that once entered in stand by the PC extinguish also all the peripheral ones connected.

Which verifications and configuration I must carry out in the bios of the PC?

How us within in the bios? Pressing which keys?

Thanks for

A:Qosmio G50-12q - How to setup devices connected to USB in standby

Hi,

Go into the BIOS and try disabling "USB Sleep and Charge".

This feature uses power when the notebook is off.

2 more replies
Answer Match 50.82%

Hello,

I have moved into a new apartment and my laptop connects to the wi-fi network but there is no internet access. The apartment is on a school if that makes a difference, I'm not using a home router. My Mac, tablet, phone etc all connect to the same network without any issues. The connection to the network works fine via an ethernet cable but I no longer have access to the port to connect this way.

I have tried going to cmd prompt to type:
"ipconfig/release" and then "ipconfig/renew" to no avail.

I have also tried the following commands with no resolution to the problem:
ipconfig/flushdns
nbtstat -R
nbtstat -RR
netsh int ip reset c:\resetlog.txt
netsh winsock reset

I have uninstalled my third-party firewall and tried selective start-up and no dice there either. I have also made sure that the IP and DNS address are obtained automatically.

Anything I can post here so someone can identify the problem please?

Thanks
 

A:Wi-Fi connected, no internet access. Other devices work

can we see an ipconfig /all
also redo the tcp/ip reset - see below

ipconfig /all

We would like to see the results from an ipconfig /all - post back the results in a reply here.

If you cannot access the internet with this PC, then you will need to paste the results into something like notepad and then copy onto a machine that can access the internet and post the results in a reply here.
Save the file to a USB flash drive or other removable media. Plug it into the working computer with internet access and copy the file and paste here.

If you do not have another PC - do you have a phone connected to the internet - can you photograph the result and post the image in a reply
Note: you will see entries named Tunnel adapter Teredo Tunneling Pseudo-Interface: we dont need to see that information - JUST the information above those entries

For Windows 8 or Windows 10
To open a Cmd Prompt or an Administrator Cmd prompt from the Desktop.
http://www.bleepingcomputer.com/tutorials/open-an-elevated-command-prompt-in-windows-8/
Use Windows + X Keys together and choose Command Prompt (Admin) from the list.​Or Right click on the windows icon - bottom left hand side - A menu appears - choose Command Prompt (Admin)[/indent]

For windows version, XP, Vista, W7
Hold the Windows key and press R
Now type CMD
Now press Enter to open a command prompt box (A new dialogue box - black with white font, will appear on screen ):​

In the command prompt window that opens, type the fol... Read more

13 more replies
Answer Match 50.4%

Hello, this is my first time posting here. I have a hp pavillion 1000 running vistaI have searched everywhere for a solution to this problem, and see many viruses and trojans that sound similar to my problem, but nothing matches it exactly (and no solutions seem to work).I believe the virus came in via a pen drive, though it has infected all of my other usb drives, including my 500 gig hard disk that contains all of my data. The hard disks inside my laptop seem unaffected.For the affected drives, directories at their root levels have been replaced by executables. If I double click these, it still launches into the directories allowing me to access my files. However, it spawns a new windows explorer. Inside the subdirectories, everything appears to be normal and the directories are just simple directories. Only at the root level are they executables. It is also impossible to "show hidden files" in folder options.Up until four nights ago, my computer had been up for over 30 days with no trouble. Now, it cannot last more than a day before all of the memory is claimed. Error boxes pop up from time to time stating "server has stopped working" or "svchost has stopped working".I would gladly just re-install at this point, except that my primary external drive would likely still be infected. I have removed everything from all of my pen drives and reformatted them but it does not solve the problem. When I create a new directory on them, within seconds a n... Read more

A:USB virus causes directories on USB-connected devices to turn into .exes

Welcome to the BleepingComputer Forums. Since it has been a few days since you scanned your computer with HijackThis, we will need a new HijackThis log. If you have not already downloaded Random's System Information Tool (RSIT), please download Random's System Information Tool (RSIT) by random/random which includes a HijackThis log and save it to your desktop. If you have RSIT already on your computer, please run it again. Double click on RSIT.exe to run RSIT. Click Continue at the disclaimer screen. Please post the contents of log.txt. Thank you for your patience.Please see Preparation Guide for use before posting about your potential Malware problem. If you have already posted this log at another forum or if you decide to seek help at another forum, please let us know. There is a shortage of helpers and taking the time of two volunteer helpers means that someone else may not be helped. Please post your HijackThis log as a reply to this thread and not as an attachment. I am always leery of opening attachments so I always request that HijackThis logs are to be posted as a reply to the thread. I do not think that you are attaching anything scary but others may do so. While we are working on your HijackThis log, please: Reply to this thread; do not start another! Do not make any changes on your computer during the cleaning process or download/add programs on your computer unless instructed to do so. Do not run any other tool until ... Read more

2 more replies
Answer Match 50.4%

Hello,
this is my second post on this subject but im editing the title slightly ...

im in need of a command or program that'll allow me to view devices on my network that my windows 7 pc can see also ?

im basically having issues using 'wireless sync' via iTunes.

I have a main router where the internet comes in .. virgin broadband...
 
...and then a Belkin access point attached to the Virgin Router using one of the ports via lan ...
 
then all my wireless devices in the house are connected to the Belkin AP, not the Virgin router.
 
when i connect the devices to the virgin router wirelessly, my pc can see them ... all good !
 
but when i connect them to the Bel..AP, itunes doesnt see them
 
so im just wanting to see if my pc windows 7, actually sees devices connected wirelessly to the Bel..AP ...
 
many thanks in advance ...
stuart

A:a program or command to view devices connected to network ?

Hi stuart,
the windows task Mgr shows you.
on screenshot
connected is my virgin/wireless(belkin usbN)
disconnected my printer

Roy

4 more replies
Answer Match 50.4%

Hi,

I've just moved to Vista, and for some reason, it won't recognize my
Wireless Network USB adapter, unless I connect it through the back of my PC.

What's wrong?
Why do the USB ports that are in the front don't work?

--Edit--

I'm sorry, I guess this should be moved to the Vista forum.
 

A:Solved: Vista won't recognize USB devices that are not connected to the back of the P

10 more replies
Answer Match 50.4%

Hi, For the past 2 weeks my internet has been playing up. Heres the problem. whenever In our home we have more than one computer on and connected to the network the latency recieved spikes into the thousands. Internet browsing speed is not affected as much its just in game lag that gets hit hard. What I noticed was once all pcs were turned off and my individual pc is the only device that was on and connected to the network the lag went away and the problem seized to exist.

We have had 2 technicians from our ISP come to our home and attempt to fix the problem but they stated that our connection is fine and the cables under the house are good. they also gave us a brand new netgear CG3100D-2 which was a last resort but that did not fix the problem too. I have done a speed test on speedtest.net while the problem was happening and the download speed is normal but the ping received shows normal on speed test but still spiking in game. Every game I play (LoL, Diablo 3 and various other online games) are all affected and im really not sure what to do to fix the problem

We currently have 2 laptops connected by WIFI and 2 pcs connected via Ethernet. Also a hole lot of mobile phones and consoles connected wirelessly to the network.

any help is appreciated

EDIT: Just playing now, My computer is the only pc connected to the network at the current time and ping still spikes

Tech Support Guy System Info Utility version 1.0.0.2
OS Version: Microsoft Windows 7 Ultimate, Service Pack 1, ... Read more

A:Solved: Latency Spiking when many devices connected to network

11 more replies
Answer Match 49.98%

Hello,

I have a number of devices connected to my virgin router, via wireless and lan.

I was wondering if their was software that exists, that allows you to monitor the speed, traffic, and what kind of bandwidth each device is getting from the router, speed etc too .

Many thanks,

Stuart

A:software to monitor devies on network, data speeds, data usage ?

Since no one has replied. Here`s a google of programs.

Google

1 more replies
Answer Match 49.98%

Dell Optiplex GX1, WinNT, sp6a. Drive is seen when booting from DOS. Drive does not exist in Explorer or My Computer. Tried different profile, no difference. Any ideas? Can I add it to Devices?
 

A:No Cdrom in devices Control Panel

9 more replies
Answer Match 49.98%

Hello guys
I have just installed a bluetooth adapter and added three devices using "control panel > bluetooth devices, so is this the same thing as doing it In "network and sharing center" > add connection or network.

And which one should you use in vista

More replies
Answer Match 49.98%

Hello

For some reason I don't have 'Bluetooth Devices' In my control panel meaning I cant bond my phone to the pc

I cant think why because I have an Acer laptop which has a special button especially for bluetooth and I know it is capabale of it because it says so on the box!

Does anyone know where I can get this option? Or how I can get around the issue

Thank you if you can
 

A:Bluetooth Devices - Why are they not in my Control Panel?!?

baby turn around and let me see that sexy body go bump bump bump..........
 

1 more replies
Answer Match 49.98%

I had this open yesterday and despite several hours of looking I cannot get it back. Anyone got any ideas?

More replies
Answer Match 49.56%

Good morning,

I am trying to teach a class and currently have a pc monitor which I will be using to control the program. In addition, we have a lcd tv connected to present what I'm working on to the class. However, I am not able to show what i'm working using the pc monitor up on the lcd tv. I've tried going to Display properties>Settings and have setup which is my primary and which is my secondary. But, it only extends the desktop but doesnt duplicate the entire desktop including icons so that what I am working on one screen while it displays on the lcd tv. Can anyone help me with this? Thx. Currently using a split vga cord setup to connect both the pc monitor and the lcd tv.

A:How to make what appears on a Monitor appear on a connected LCD monitor

http://www.ehow.com/two-monitors-on-one-computer/

Louis

5 more replies
Answer Match 49.14%

HP Probook 450 G2 biometric devices is missing from control panel  plz help how i can fix it Thanks

More replies
Answer Match 49.14%

I have looked for help all over the internet and cannot find a solution: My fingerprint reader shows up in Device manager, but I cannot do anything with it if Biometric Devices does not show up in Control Panel!! what's wrong? I have ALL the right and updated drivers.
thanks!
Joe

A:Biometric Devices not showing up in Control Panel

Hi Joe and welcome to Seven Forums.

Some folks have suggested installing this driver:

AuthenTec Customer Support > Downloads > Windows > Drivers

Additional suggestions on this Microsoft forum thread:

no biometric devices in control panel

And this blog:

Biometric Devices Missing from Windows 7 Control Panel | 1N73RNET1N73RNET



   Warning
At a minimum, I would strongly suggest making a Restore Point before installing/uninstalling any drivers.

System Restore Point - Create

System Restore

9 more replies
Answer Match 49.14%

i have no sound and i think the mute is on but wheni go to volume control it says "there are no active mixer devices available" any one got any ideas?
 

More replies
Answer Match 49.14%

Hello! I was trying to use bluetooth to synch my Blackberry Perl phone with my Dell Desktop running Win XP SP2. After reading info on the Blackberry site about why their software would not allow me to enable a bluetooth connection, I uninstalled the Widcomm bluetooth software from the add/remove programs from the PC. The Blackberry site said that I could only synch wirelessly if the MS bluetooth stack was in control.

Now that I uninstalled the Widcomm software, I don't have bluetooth in the control panel or the devices listing. I tried to
scan for new devices, but no bluetooth.

It's funny though, I am using a bluetooth mouse and keyboard, and they are working fine. I cannot, however, pair my phone anymore.

Any help would be great! Thanks!!!

Jill

A:Bluetooth Missing From Devices/control Panel

Can you download it for free at the site of that program?

3 more replies
Answer Match 49.14%

Hello,

I have a strange problem. My laptop suddenly stopped connecting to the wifi network (comcast) last night. Interestingly my lenovo tablet, mobile phone and another laptop are able to connect to my wifi network without any issues.

I have also tried the following steps to troubleshoot:
1. switching off the router for 30 secs
2. Resetting the router
4. Restarting the computer
5. Releasing the ip and disconnecting the computer from the network followed by a reconnect.
6. Manually attempting to connect to the wifi network

Note: Interestingly I was able to connect to a neighbor's unsecured wifi network so I am presuming the wireless adapter is working.

I have run out of ideas on how to trouble shoot this further. could any one kindly help ? I have pasted below the windows Network Diagnostics report

[Ref: my home network is HOME-8AA2]
_______________________________________________________________________________________
Windows Network Diagnostics Publisher details

Issues found

The connection between your access point, router, or cable modem and the Internet is broken

Detected Detected

Your broadband modem is experiencing connectivity issues Completed

Issues found Detection details

6 The connection between your access point, router, or cable modem and the Internet is broken Detected Detected

The network gateway is accessible, but Windows couldn’t receive network traffic from the Internet.

Your broadband modem is experiencing connectivity issues Complete... Read more

A:Solved: unable to connect to wifi with laptop but other devices remain connected

------------------------------------------------------------------------

Remove the wireless security
Is your wireless security enabled?
if so - log into the router and remove the wireless security - now see if it will connect.
if it does - log back into the router and try with the wireless security enabled again

------------------------------------------------------------------------
 

3 more replies
Answer Match 49.14%

Last visit: 04-Oct-2004 08:22 PM

First Question:

Anyways, my internet is freaking slow because my sister always download stuff so i was wondering if i had TWO routers and i connect to the "new" Linksys and she connects to the "old" D-Link, will that work? Will this still be slower? I asked some people and they said the "router" is working too much or something, so having two will help?

So the config would be: ISP Modem -> Linksys -> D-Link ( D-Link will be wireless for my family to use, and me and my friend will be using the Linksys wired )

Another Question:
Also, i got another question. If my ISP allows me to have TWO IP Addresses, will it make my internet slower if i gave one of the IP to my D-Link and one to Linksys router?

If not, how would i make my internet faster?

Current Setup:
One Modem, One Router:

Sister uses Wireless and downloads songs and movies ( Sometimes with BT )
I use Wired and play games like BF2/CS/CSS/WoW and all the other games.
Another comp: Hosts a "game" and sometimes plays War3

** I do NOT want to shut "game" down, EVER! So please dont tell me to turn it off =\ **
 

A:Q: Does router connected to a router work?Another Q: ISP /w 2 IP?

Can't tell from what you've told us so far, but I would guess that the bottleneck is your ISP connection. What is it's bandwidth (speed) supposed to be? Are you and the other computers using all that bandwidth? Probably so, but if not then it could be a router problem.

If you have DSL the only way you will get faster is if they offer more than one service and you upgrade to a faster, more expensive service.

If you have cable and can get two IPs then maybe you can get double the bandwidth; ask your ISP.
 

2 more replies
Answer Match 49.14%

Hello,
I have a linksys wireless router on my bottom floor, and the wireless capability does not reach my top floor. Right now I have a very long ethernet cable running from my router to my upstairs computer. I am interested in putting another computer upstairs, however i cant use wireless because it gets very low, or no connectin.

Would it be possible to Connect my long ethernet that runs through my house to upstairs to another small router, or ethernet splitter, in order to get internet capabilities on both computers upstairs? Would it be extremely slow? thanks in advance if you can help.
 

A:Will a Router connected to a Router work?

16 more replies
Answer Match 49.14%

I have a Motorola 3347 modem/router supplied by Qwest. I have been frustrated because my internet speed is limited, partially because of Qwest service, partly because, I was told by the installer, that my apartment building wiring keeps the speed from reaching what I pay for from Qwest (the second to fastest package, can't remember). Can't get Comcast on this block.
Does anyone know if it would increase the reach/speed of the wireless network if I connected my Linksys wireless G router to this Motorola modem/router? I don't know if it's even possible, but I want to do this because when trying to use internet in one of the bedrooms, the internet signal is fairly weak. I was wondering if my linksys router would be stronger than the qwest modem/router in one.
If it is not possible to use the linksys router as the main wireless network and disable the qwest modem/router so it was strictly a modem, would it work better to see about just requesting a modem from qwest (what I've usually done with comcast), and then using my router? Or would a range extender be a better solution?
Thanks for anyone's help
p.s. I'm also thinking my linksys router might not help the range/speed problem enough, in which case I'd buy something like belkin N+
 

A:Router connected to modem/router

tmpk said:





I have a Motorola 3347 modem/router supplied by Qwest. I have been frustrated because my internet speed is limited, partially because of Qwest service, partly because, I was told by the installer, that my apartment building wiring keeps the speed from reaching what I pay for from Qwest (the second to fastest package, can't remember). Can't get Comcast on this block.Click to expand...

If the statement is fact (highly likely too), then nothing from your modem to any of your equipment will make any difference



p.s. I'm also thinking my linksys router might not help the range/speed problem enough, in which case I'd buy something like belkin N+Click to expand...

BAD idea. None of the 11n stuff is official and there's lots of compatibility issues with it (belkin or any other).
 

4 more replies
Answer Match 49.14%

I have a linksys WRT54G router connected to a beetel 110TC2 modem. I want to get a static ip address for port forwarding. Can anybody tell me how to get a static ip and how to do port forwarding?

A:How to get a static ip on a router connected to a router?

You access the router with your browser, ip address for the linksys is 192.168.0.1 or 192.168.1.1 and the default user is admin and password is Admin with capitol A, you can then change it to what you want it to be by taking DHCP off auto, as for the port forwarding, do some searches on the net for some all inclusive info...and welcome to the forum!

5 more replies
Answer Match 49.14%

ISP: Charter
Router 1: Linksys E4200
Router 2: Cisco 881 Integrated Services Router

My wife will be working from the house and her company requires her to use one of their routers (Cisco 881 Integrated Services Router) so they have a level of security via he computer. And being all her work is data entry via internal network.

My question is can i run that router through my Linksys E4200? What i mean is i will not have admin control over the 881 series for personal computers or devices so i want to keep my router in the lead so i can control my internet and network.

It would go:

ISP Charter Communications ----> Personal Linksys E4200 ----> Wife's business Cisco 881 Integrated Services Router on one connection. That possible?
Thanks
Dennis
 

A:Solved: Is it possible to use a Router connected to a Router?

7 more replies
Answer Match 49.14%

Hello everyone. I was just wondering how to control a fan's speeds that is directly connect to the PSU (not in the PSU.) I ask this because i have two fairly loud case fans that need power from the PSU directly.

I was just wondering if there is an adapter or controller I could buy that would quiet them down a bit.
 

A:How to control a fan connected directly to the PSU?

here is one that i found to just give you an idea of what there is...
http://www.newegg.com/Product/Product.asp?Item=N82E16813999504
 

3 more replies
Answer Match 48.72%

I use w10 on 3 devices, a mid range gaming PC, linx7 tablet, and lumia640. On the whole the experience is pretty good, syncing works well, reminders, alarms, contacts etc. This was one of the reasons I opted for android early, using chrome on a PC gave a similar, yet skimmed down, one OS feel.
I've not had one BSOD since updating the 'rig', my mobile works great, and the tablet is amazing for ?49! I was talking to my father in law who uses all 3 main OSs every day, and we both agree that windows just feels more 'grown up' than iOS or android. He wants a win10 phone next to replace his android (he'll have to keep the company iPhone4).
So like I said, does anyone else have a similar experience?

A:Who else uses w10 across multiple devices?

yeah i have no probs with my Lumia 920, HP work laptop and 2 of table computers at home.

just pisses me off to have the same background on each computer and i seem not to be able to find a setting to keep that sync out

2 more replies
Answer Match 48.72%

I want to use the audio simultaneously from my ati 4550 HDMI, Sony blue-tooth speaker via usb BT dongle, 3.5mm jacks on my mobo, and also from a spdif and digital coax linked to the mobo via on board header to expansion bracket with ports.

I know this all may sound like overkill, however I don't have the funds for high end switches / replicators, etc. So manually changing them has been a hassle.

I have done some reading and I know se7en doesn't let you. I did this with xp x64.

Anyone know of a "work-around" or hack to enable all devices at once?

Intel E2140
Intel DQ965CO
4gb Kingston 667mhz
MSI r4550
Ultra MD3 Dashboard
Gyration RF MCE Universal Remote

A:USE MULTIPLE DEVICES 7 x64

From what I see, you can only have one "Default" Playback device so I doubt that what you want to do can be accomplished.

2 more replies
Answer Match 48.72%

Hi, I really hope you can help me, this is driving me nuts!

I cannot install *any* new USB devices. I have tried several memory stick type devices and a 3g modem card. They all work on other peoples laptops fine.

In all cases my Dell laptop (Latitude D600) finds the hardware and the Add new hardware wizard pops up as expected. I click ok to install the driver and after a short while it fails with the message "data is invalid" ...and no clues as to what this means.

USB devices (a webcam, camera and 2 memory sticks) that were installed many months ago are all ok and still work fine.

So... it isn't a hardware problem, it must be something Windows does when installing a new device.

Any ideas how I can fix it?

Thanks!
Marco

More replies
Answer Match 48.72%

... but not mine
 
I made these logs yesterday, 30-29-15, and they were modified 2 minutes after being created (They were modified 2 mins after being run but not by me).
 
 
 
I'll wait patiently to hear from one of you. Thanks again for doing what you do. I think I'd like to join up for the training & volunteering program, these skills are practically priceless at this point (at least it seems like it to me!)
 
In the mean time, heres a bit of info.
 
I ran across a log file last week in which microsoft is logging some updates and then refers to "hearbleed." (I've seen this log file before, too, although this time I stopped and read carefully). According to the log, heartbleed update attempt was a success, but 3 error codes were thrown up. This makes me wonder if heartbleed isn't the primary means of access and control here. Oh, and I change my router's gateway login password ~ two weeks ago, and 1.5 days later it was altered so I eventually had to factory reset. There are a million things I could list... I've been at this for months now with multiple each of system restores, system repairs, malware scanner bonanzas, and full system format (with somewhat slow/cautious reintroduction of backed up files).
 
Also, last night the attackers officially got into my girlfriend's mac. It was probably my fault for clicking to most obvious (but juicy) bait folder which was sitting on her desktop and executing plaintext files to read them (I'm an i... Read more

A:Over My Head - home network (with 5 users / 10+ devices) is under control :(

Hello and welcome to Bleeping Computer! I am HelpBot: an automated program designed to help the Bleeping Computer Staff better assist you! This message contains very important information, so please read through all of it before doing anything.
We apologize for the delay in responding to your request for help. Here at Bleeping Computer we get overwhelmed at times, and we are trying our best to keep up. Please note that your topic was not intentionally overlooked. Our mission is to help everyone in need, but sometimes it takes just a little longer to get to every request for help. No one is ignored here.
To help Bleeping Computer better assist you please perform the following steps:
*************************************************** In order to continue receiving help at BleepingComputer.com, YOU MUST tell me if you still need help or if your issue has already been resolved on your own or through another resource! To tell me this, please click on the following link and follow the instructions there.CLICK THIS LINK >>> http://www.bleepingcomputer.com/logreply/581427 <<< CLICK THIS LINK
If you no longer need help, then all you needed to do was the previous instructions of telling me so. You can skip the rest of this post. If you do need help please continue with Step 2 below.
***************************************************If you still need help, I would like you to post a Reply to this topic (click the "Add Reply" button in the lower right hand of t... Read more

2 more replies