Tech Problem Aggregator

Hi everyone i have router configuration error...

Q: Hi everyone i have router configuration error...

Hi, I am actually trying to configure a router, with a serial and fast ethernet interface..
now i have a network address of 192.168.50.1 and i have used 192.168.50.2 for the fast ethernet interface and 192.168.50.3 for the serial interface, but it giving me an error, saying its overlapping the fast ethernet address of 192.168.50.0, is there anything i'm doing wrong there? can anyone help me please...

A: Hi everyone i have router configuration error...

6 more replies
Answer Match 53.76%

Hello Everyone,

I just wanna ask for some help regarding configuration of a vpn firewall router that is connected to a 4g modem/router combo.
I am new in setting up a vpn and not so much familiar with others things or what setup is necessary, kindly help the poor guy please???

This is what I need:
- I need to connect the VPN FIREWALL router and use its features at the same time connected to the internet ( the VPN FIREWALL will act as the security for the whole network and the 4G modem/router will be the one supplying the internet)
- Need to establish a VPN connection later after the configuration.
- The server and other lan pc's must be accessible outside the local network when connected to VPN (web server, local pc's shared folder and files, etc)

Here's some details that i hope might help:
- I am using a Quanta 1K5 4G LTE modem/router combo
- I am using a Dynamic public IP address,( but this is not a problem because i am using s DDNS)
- My VPN FIREWALL brand/model is Micronet SP881 B VPN FIREWALL router
- Right now i am already connected to the internet using the vpn firewall physical connection is:
4G modem/router-->hub-->VPN firewall router-->PC
my connection is 4G(LAN)-->VPN (WAN) set the connection type to Dynamic IP
-The remote connection and remote access (web server, ftp,RDP) is working fine on the 4G modem/router alone.

I attached some screenshots of the VPN firewall router
Looking forward to hear from you guys, Thanks in advance!
&nb... Read more

A:HELP! 4g modem/router combo to vpn firewall router configuration

7 more replies
Answer Match 48.72%

I want to configure a wireless router on my compute

steps taken

wired conn- run the cd-put user/password and with wired connection I am able to go on line and once I am taking out the wire from the laptop it shows "page cann't dispaly"

A:router configuration

and welcome to the Forum

See how much this helps your understanding of networking:

http://www.homenethelp.com/web/howto/net.asp

1 more replies
Answer Match 48.72%

I am attempting to set up servers for various games on my PC. The only problem is the my system connects to the internet through a (wireless) router and others (non-LAN) cannot connect to me. I have read many articles on opening router ports and configuration settings but it is all too confusing for me to figure out and i dont want to screw up my low-latency connection! Does anyone know how to make this work?
 

A:Router Configuration

Go here
and find your router and it has good instructions to set up port forwarding. They might even have the game you use listed.
 

2 more replies
Answer Match 48.72%

I currently use a router with my isp connection through the cable provider in my area .The problem I am experiencing is when the computer is plugged DIRECTLY into the cable modem provided by my isp, bandwidth(via speed test) is at expected speeds .
(cable modem is a thompson dhg574)

HOWEVER once the router(dlink DLR-645) is plugged in to the cable modem the bandwidth essentially cuts in half (@7mbps)or more of the 20mbps service I subscribe to.

I know that the router can be successfully configured because it was set up in the past but I no longer have the information to do it anymore.


Tech Support Guy System Info Utility version 1.0.0.2
OS Version: Microsoft Windows 7 Home Premium, Service Pack 1, 64 bit
Processor: Intel(R) Core(TM) i3 CPU M 370 @ 2.40GHz, Intel64 Family 6 Model 37 Stepping 5
Processor Count: 4
RAM: 7988 Mb
Graphics Card: Intel(R) HD Graphics, -325 Mb
Hard Drives: C: Total - 476837 MB, Free - 395883 MB;
Motherboard: Dell Inc., 08VFX1
Antivirus: Microsoft Security Essentials, Updated and Enabled
 

A:router configuration help

11 more replies
Answer Match 48.72%

I am trying to configure my router so that it will play Asheron's Call. I went onto portforward.com and my router is Linksys WRT54Gv6. I go to the default IP address for configuration and when it asks for my password/username, none of the ones that were given (i.e. blank or admin) work in any combination. I was wondering if anyone would know how to find out this information for this model/version or if there is another way to port forward the ranges 9000-9001, 9004-9005, and 9012-9013? Thank you!
 

A:Router Configuration

6 more replies
Answer Match 48.72%

hi,

could anyone please let me know the router configuration steps.
 

A:router configuration

best place to look is in your router's user guide.
 

3 more replies
Answer Match 48.72%

I would like to access my router to configure it for maximum internet connection speed. The router is a NetGear WGR614v4 with both wireless and hard wire connections . My operating system is Windows XP Professional and I use a cable high speed interenet service. My router is out of the warranty period and NetGear will not provide tech support.
 

A:Router configuration

14 more replies
Answer Match 48.3%

my xbox 360 online runs through my pc i've just changed to a wireless connection for my pc and now my xbox wont regester with my pc sayin it doesn't hav th ip adress and tells me to go to my router configuartion web page where do i find this?
 

A:router configuration web page

9 more replies
Answer Match 48.3%

Is there any security benefit (extra firewall, etc) from using two routers to connect to the internet. For example, this computer connects to port 1 on my Netgear. From the WAN port, a wire connects the port 4 of my Dlink. The WAN port of my DLink connects, of course, to my modem and the Internet. second question...how do I access the secondary router. Anytime I type in "192.168.0.1", I only access the DLink interface. (I was confused about configuring the Static IP on the secondary Netgear so I left it as is) Any ideas/ suggestions. Can I somehow use this dual router to my benefit?

I have a Netgear (RP614) and DLink (DI 714P+). Networking has always somewhat eluded me, and I was wondering what benefits/unique configurations may be derived from two routers.

Here is the setup.

Thanks in advance

-R
 

A:Dual Router Configuration

6 more replies
Answer Match 48.3%

I am running a Netgear WGR614V5. I can connect fine to the internet and everything using the tourer but I cannot connect to the router configuration page. I did have a password setup on it, but I was connecting to it earlier today fine. For some reason the reset button does not seem to be working. When I ping 192.168.1.1 none of the packets are received. When I put in ipconfig /all this is what comes up.
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Unknown
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
DNS Suffix Search List. . . . . . : hsd1.mi.comcast.net.

Ethernet adapter Local Area Connection:

Connection-specific DNS Suffix . : hsd1.mi.comcast.net.
Description . . . . . . . . . . . : CNet PRO200 PCI Fast Ethernet Adapte
r
Physical Address. . . . . . . . . : 00-08-A1-31-A0-97
Dhcp Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
IP Address. . . . . . . . . . . . : 68.41.138.90
Subnet Mask . . . . . . . . . . . : 255.255.252.0
Default Gateway . . . . . . . . . : 68.41.136.1
DHCP Server . . . . . . . . . . . : 68.87.77.13
DNS Servers . . . . . . . . . . . : 68.87.77.130
68.87.72.130
 

A:Router Configuration - 192.168.1.1 Not Working

8 more replies
Answer Match 48.3%

I sent over a Linksys DIR-615 router to a friend in Venezuela as he does not have any wireless internet, now from my understanding and what he has explained he has a modem to router connection already, however the router does not have wireless.

He got the router today and I told him to replace his current router with the one I sent him. Now the connection going from his modem to router wouldn't work in the WAN port. So we placed it in LAN ports along with his two PCs and great, he got internet on both computers but he can't access the router configuration to set the wireless.

Now I made sure it all worked before I sent it, I replaced the router I have at home with it and it worked with the IP 192.168.0.1
However when he enters that it doesn't bring him to the router configuration, nor with 192.168.1.1, 192.168.1.2, 192.168.0.2 and some others.

So I told him to use ipconfig to get the gateway IP and trying to use that to access the router, but still it won't work.
The Ipconfig looked like:

Adaptador Ethernet Conexión de área local :

Sufijo de conexión específica DNS : cantv.net
Dirección IP. . . . . . . . . . . : 201.210.21.98
Máscara de subred . . . . . . . . : 255.255.224.0
Puerta de enlace predeterminada : 201.210.0.1

So basically I have come here in search for help on how I can get to the router configuration and enable the wireless for them.
Anything you ask I can ask of him and report back.

Thanks in advance!
 

A:Need help with router configuration connection.

So.is there a default gateway listed in the ipconfig above ?
And you said linksys.Did you mean d link ?
Is the ISP cable or dsl ?The setup would be different I believe.
Might be a good idea to go back to basics,just to make sure that everything was done in the correct order.Like so.
Tips on setting up broadband connection, courtesy of Johnwill

You don't need any setup disk to configure a broadband router.
. The following procedure should get you a connection with any broadband modem that is configured to use DHCP for the router connection, such as cable modems, and many DSL modems. If you require PPPoE configuration for the DSL modem, that will have to be configured to match the ISP requirements.
• Turn off everything, the modem, router, computer.
• Connect the modem to the router's WAN/Internet port.
• Connect the computer to one of the router's LAN/Network ports.
• Turn on the modem, wait for a steady connect light.
• Turn on the router, wait for two minutes.
• Boot the computer.

When the computer is completely booted, let's see this.

Hold the Windows key and press R, then type CMD (COMMAND for W98/WME) to open a command prompt:

NOTE: For the items below in red surrounded with < >, see comments below for the actual information content, they are value substitutions from the previous command output!

In the command prompt window that opens, type type the following commands one at a ti... Read more

3 more replies
Answer Match 48.3%

Hi folks,

Glad to be on board, this website came highly reccommended by to me by some fellow members of a Boston Red Sox fansite, and I must say, the info here is great.

I finally have a question to ask:

Recently, I set up a pretty complete wired home network so that I could work from home more often. In so doing, I added two laptops and another desktop to my office, which used to house just a single desktop. They are all connected to my cable modem through a router.

Over the past several months, my partners and I have been using AIM and MSN Messenger's talk programs (I believe this is called Voice-over-IP, is it not?) pretty regularly throughout the day to stay in touch.

When the single PC was connected to the internet without a router, these programs worked easily and flawlessly. Now, as the four PC's are connected to the internet through the router (and are therefore behind the router's firewall??) I can not use either application for voice conversations on any one of the four PC's. Simply put, they will not establish a connection to my peers on the other end.

I am now on my second router (switched from D-Link to Belkin). The tech support from both companies has been horrible, and neither has been able to help me connect using these apps at all. They are all pretty sure that I will eventually need to open the correct port or ports, and will need to configure the router accordingly, but none of them seems to know how to do so themselves, and as suc... Read more

A:Router Configuration Problem(s)

i think you have open the ports in the router setup,have a look in your manual
mine come under advanced features,coference and telephony
 

2 more replies
Answer Match 48.3%

Hey all,

Not sure if I'm in the right forum. A couple months ago I had to switch providers, and had to get hooked up with a wireless router. Ever since then, my download speeds have crash landed.

I'm running XP. Any tips on where to go for help would be appreciated.

thanks!
 

A:need help with wireless router configuration

What bandwidth are you supposed to be getting?

What speeds do you get with a test such as Speakeasy connecting by wireless, by ethernet to the router and directly to the modem?
 

1 more replies
Answer Match 48.3%

I have been dealing with the same issue for the last couple months. I only need the router because I use my cable connection for TiVo. I am going to try your instructions.
 

A:Router configuration issues

11 more replies
Answer Match 48.3%

My Internet cable is rj45. If i connect that cable directly to my pc, and set up the connection (PPPoe, requires a username and pass), i can access the internet.
then i bought a tp-link wr841n router which has a Wan (rj45) i/p socket.
and i ran the tp-links setup software, configured the router with the username and pass, but still it wont connect to the internet.
and help please ?
 

A:Solved: Router configuration

6 more replies
Answer Match 48.3%

Hello everyone.
I just acquired a tablet (Transformer Prime) and wanted to add another wifi router to my network connection as a way to increase the signal on my room. I tried following the instructions on this Linksys help article:
http://www6.nohold.net/Cisco2/ukp.aspx?pid=80&login=1&app=search&vw=1&articleid=4579

I've tried the first method described and completed all steps and still couldn't connect the second router. when i connect both by the ethernet socket only the first one, unaldutered, worked providing internet access to my PC by wire but the second one didn't increased reception on the tablet at all.
Ipconfig shows no sign of any other device besides the working router when they are connected by the ethernet socket. When i connect only the second router ipconfig reveals there is no "Connection-specific DNS Suffix" and "Default Gateway". I cant change options back to normal in the web browser because i dont have a default gateway number anymore

What have i done wrong? how can i fix this and configure this damn router to give me my precious wifi speed?
Any help would be appreciated and I'm verry sorry for the long and badly explained post (im a noob with pcs, to say the least)

BTW: first post, but I'll introduce myself later on a proper post
 

A:Problems with second router configuration

Reset the second router to factory default settings and try the following procedure. It is the same as your linked article Option 1, but maybe it will be easier for you to follow.

JohnWill's procedure (Aug. 30, 2008) for configuring a secondary router as a switch and, optionally, wireless access point follows.

Connecting two (or more) SOHO broadband routers together.

Note: The "primary" router can be an actual router, a software gateway like Microsoft Internet Connection Sharing, or a server connection that has the capability to supply more than one IP address using DHCP server capability. No changes are made to the primary "router" configuration.

Configure the IP address of the secondary router(s) to be in the same subnet as the primary router, but out of the range of the DHCP server in the primary router. For instance DHCP server addresses 192.168.0.2 through 192.168.0.100, I'd assign the secondary router 192.168.0.254 as it's IP address, 192.168.0.253 for another router, etc.

Note: Do this first, as you will have to reboot the computer to connect to the router again for the remaining changes.

Disable the DHCP server in the secondary router.

Setup the wireless section just the way you would if it was the primary router, channels, encryption, etc.

Connect from the primary router's LAN port to one of the LAN ports on the secondary router. If there is no uplink port and neither of the routers have auto-sensing ports, use a cross-... Read more

1 more replies
Answer Match 48.3%

I recently bought a NetGear Router to setup my lan to use internet access to more then one PC. I finally got everything working fine. However, I am curious on what is PPPoE use for?

Could some one tell me what this is use for and what it means.

Thanks in advance.
Charlton
 

A:NAT with PPPoE Configuration on router???

9 more replies
Answer Match 48.3%

Hi I have a D-Link DSL 604+ Router and modem conected to a 2mb broadband connection which works fine appart from me only getting 2kbs download speeds when using bittorrent. I have been told that this may be because i have not configured some ports on my router? Is anyone able to help me solve this problem Please
 

A:D-Link Router Configuration

Won't get much help with this issue due to the function of bittorrent....I doubt it is your router, however

http://forums.techguy.org/faq.php?faq=vb_read_and_post#faq_faq_p2p
[tsg=welcome]to TSG![/tsg]
 

1 more replies
Answer Match 48.3%

For some time now, my home LAN has been experiencing some problems. The router (an ss2624 speedstream wireless) sometimes doesn't want to work, (or most of the time) and sometimes it does. I have three computers connected to it, and they all can access the router's web page. However, none of the computers recieve internet access.

One of my computers is able to connect the the cable modem directly and receive internet. I use all the numbers I see from running winipcfg on my directly connected computer when I setup the router, but for some reason the router will not work. I make it so that it uses a static IP address from the ISP (which I'm not entirely sure even is static, even though I always see that same IP address, I also see a DHCP server number) and also I put the DNS server I see, although I am able to choose between 4 different numbers. (I put the others as alternate.) Am I missing any information from my ISP?

A:Router configuration problems

Set your router back up to receive DHCP if your ISP requires it. Sometimes ISP's use private IP's for you, that conflict with your current router config. If your router IP is 192.168.1.1, then make sure the IP that you get from your ISP is not 192.168.1.(1-254) Earthlink is bad about this. If it is the case, just change your router (inside address, not the external ISP address) to 192.168.10.1 or something other than 192.168.1.1 just change the second to the last number to anything else.

Not the best at drawing a mental picture here. but

If WAN address is 192.168.1.1
and router is 192.168.1.1 , they conflict. Plus the router needs a different network like 192.168.2.1 for you to be NAT'd

Hope this helps.

2 more replies
Answer Match 48.3%

How can I find all the companies ip address for setting up wireless router? For example, Netgear, Linksys Dlink, and other compamies.
Thanks!!!!!
 

A:configuration of wireless router

How can I find all the companies ip address for setting up wireless routerClick to expand...

do you mean what default gateway they use
ie 192.168.0.1
or
192.168.254.254
etc

you could look in all the manuals - a lot of routers manuals are on the manufacturers sites - it would also give you the default username and password

why are you after so much info???
 

1 more replies
Answer Match 48.3%

hi there. my name is fred and i heard about a router configuration panel that people with routers for their dsl and cable internet connections. is that true? if it is how do i get to it. i heard of one way but it doesnt work. i know my router/cable modem is from rca. and i know my ip address. since i dont know how private that is i will just leave it at that. any help??
 

A:router configuration panel????

The router configuration panel differs from brand to brand. Linksys, for example, has a default of 192.168.1.1, with a blank username and 'admin' as the password. DLink routers use 192.168.0.1.

Do you know what the IP of your router is?
 

2 more replies
Answer Match 48.3%

Hey guys i was wondering if you could help me Port forward and or Proxy my Wi-Fi router.... Im using a TP-LINK WR340G.. really need help.
 

A:Wi-Fi router proxy configuration help

Port forwarding has these requirements

the machine to which the forward will point to must have a static IP address
once port(s) are so configured, NO OTHER system will be able to use those ports.
(1) can be done manually on the target system, or more easily in the router by using IP Address Reservation.

Pg 33 of the manual describes (1)

Pg 34 describes the setup for port forwarding
 

3 more replies
Answer Match 48.3%

Hi guys!
I have a Wireless Router,Belkin F5D7230-4 Router.
Model: F5D7230-4 - Data Transfer Rate: 54 MBps - 2.4 GHz - Wireless Connection.

1)Previews we changed default ip address 192.168.2.1 to some thing.But now I forgot that default page ip address.How to get that page.I restarted that back side button.But it is not getting.Can any one any one?

2)How to configure it?

Thanks for Apperication.......
 

A:Wireless Router configuration

Hold the reset button for about 15 seconds. After that you should be able to use the 192.168.2.1 address to get back to the config page
 

1 more replies
Answer Match 48.3%

I recently purchased and installed a Linksys RT31P2 wired router while converting to Vonage VoIP. I installed the RT31P2 behind an Actiontec GT-701 DSL Gateway (modem/router). I plugged a telephone into the RT31P2 and my VoIP phone service works great. Because my Actiontec GT-701 DSL Gateway only has 1ea Ethernet port, I had to remove my local computer from the Actiontec Ethernet port so that I could connect the RT31P2 to the same Ethernet port. After removing the local computer from the Ethernet port on the Actiontec GT-701, I moved it an open Ethernet port on the RT31P2. The local computer has Internet access and appears to work normally accept that it can no longer file or print share with the other computers on my home network. Prior to this change, I had 3ea wireless NIC-connected computers and the Ethernet-connected local computer configured onto my local network via the Actiontec GT-701 DSL Gateway. All of these computers were configured to file/print share and did so successfully. After the installation of the Linksys RT31P2 router, the local computer can no longer file/print share with the 3ea wireless NIC-connected computers. I have some basic networking knowledge and I understand that by adding the Linksys RT31P2, I have essentially created two networks. The problem appears to resolve around the fact that there two networks are currently not able to properly communicate in a manner that will allow file/print sharing between them. Is this problem solvable utilizing ... Read more

A:Multiple Router LAN Configuration

16 more replies
Answer Match 48.3%

Hi everyone, new here. I've just got a buffalo airstation WZR-1750HP and i cannot for the life of me configure it for internet access. I have entered my isp username/password but still no joy. I must admit i'm utterly hopeless with networking, but not bad with other computer matters. Hoping some wireless whizz kids can tell me what my settings must be.

A:router configuration woes

Dual band AC routers can be tricky as they sometimes are not compatible with older wireless N clients.

Best to upgrade any wireless n NIC's to AC NIC's if they can't connect consistently.

Also depends on if there are any other routers in the network, or if the modem is a modem/router or just stand alone modem, not enough information here for me to give directions.

2 more replies
Answer Match 48.3%

I am using an edimax 3G-6200n router with a 3G usb modem on the '3' network to connect to xbox live. I can connect easily and play most games and join most partys but sometimes i cannot join certain friends games and matchmaking is slow on some games such as modern warfare 2. I have tried DMZ and UpNp on the router but the NAT remains strict. Any help would be greatly appreciated. Thank you.
 

A:Edimax router configuration

Do not open multiple threads on the same topic. You already have replies here.
 

1 more replies
Answer Match 48.3%

I have a WNDR3700 connected to a wired network that I access through wireless. When I get pretty far away from the WNDR3700 I loose the ability to connect and I was thinking if I could extend the wireless network by adding a DAP-1522.

I want to have the WNDR3700 and the DAP-1522 connected via wireless and using a laptop I want to be able to access the wired network from anywhere in the facility.

Can this be done and could you guys tell me step by step how to do it, I will definitely appreciate.
 

A:Router plus Bridge Configuration Help......

Hi,

For best performance is good to have cable installed between WNDR3700 and d-link access point at remote location. All those repeaters, extenders and wireless distribution systems affects wireless performance.
 

3 more replies
Answer Match 48.3%

I have a (hopefully rather basic) problem with the configuration of my new D-Link router DIR-657.

Now, what I had in mind was rather simple, but apparently I don't know the correct settings to
achieve it... (A lack of knowlegde on my side, I guess. I have some experience setting up simple
networks with a few windows computers and broadband modems, but the last time was some
time ago and this one here seems to be a bit more complicated than I thought...)

I have one PC (Win7 Ultimate 64) with a 3G modem (via USB) and want to use this computer (PC1)
and the 3G connection to act as the internet connection (using ICS) for my home network.
This computer now connects to the new D-Link router (via LAN).
I want to use this router to connect the other devices in this network (LAN/WLAN) with PC1 so they
can also use this internet connection (via ICS) and also for the other basic network uses (file sharing,
printing, ...).
The setup of ICS was not a problem (I think) and the local network (LAN/WLAN) is working alright,
but how do I have to configure the router so he "knows" that all internet traffic is going through the
3G connection (ICS) at PC1 (LAN port) and not its WAN port (which is empty) while maintaining
the functionality of the network (file sharing, printer,...) of course.

[FYI... I want to use PC1 (with 3G) for my internet connection because I want/need the VPN
connection I have installed on this PC. While there are a few (WLAN-)router out there that can
hand... Read more

A:ICS + LAN/WLAN Router configuration

9 more replies
Answer Match 48.3%

I have 6 units of PC and i have 2 Internet Service Provider (ISP).

Using a dual WAN Router, how can i configure it to have my 3 PC connected to 1 ISP and the other 3 PC is connected to another ISP.
ISP 1 >>> >>> 3 Computers
>>> Dual WAN Router >>> Switch/HUB
ISP 2 >>> >>> 3 Computers
Just thinking if it is randomly get an access to net. If there is a way to configure or assign them on which connection them will be pls. guide me.
If can't get my illustration i will make a better one. ^_^

hmMm... and does this settings can connect my 6 Computers with each other? So, that i will have an access to them? Or in use of LAN Games or File sharing?
p.s.

what is the disadvantage and advantage of this settings?
 

More replies
Answer Match 48.3%

My computer wouldn't wake from sleep mode a few days ago so I hard rebooted it. When it booted I no longer had internet access.

My local area connection was listed as an unidentified network with no network access. I used the troubleshoot tool on the connection and it returned "the router does not have a valid IP configuration". I could not change the network from public to home/private.

I am able to connect to the internet using the same router and cable on this laptop. The wireless is also working fine.

I have tried:
disabling and enabling the network adaptor, DHCP and the local connection
updating the network card drivers
disabling ipv6 in local connection
Resetting the router to factory settings
I disabling bonjour (I do not have and have never installed mcafee)
clearing the TCP/IP stack with netsh int ip reset
using ipconfig /release /flushdns /renew
system restoring to before the issue occurred
doing a clean install of windows (it saved my old files under windows.old - I assume this is still a clean install)

I am running windows 7 home premium 64, my network card is an Intel 82567LF-2 Gigabit, the router is a Thomson TG782T and I am using Bigpond ADSL2+.

It's been a couple of days and I'm well out of my depth. I didn't expect the issue to continue after a clean install. Any help would be really appreciated. Attached is the ipconfig I get. Attachment 288972

A:Router does not have a valid IP configuration

If you could attach your ipconfig please because I can't see it

This can help us determine possible causes

Josh

9 more replies
Answer Match 48.3%

Hi,

Been having problems with my router today, was working fine and then all of a sudden dropped out.With a notification that the Modem wasn't working. I plugged in my laptop via Ethernet to Modem and it worked as fine.

Contacted my ISP and they said it was the router just broke, therefore I purchased another Router today, to my disbelief, still the same problem,can connect via ethernet but not WLAN.

Devices will connect locally but not to the internet.

Any ideas?

Thanks, Russ
 

A:Help needed with Router Configuration

is this all wireless devices cannot connect to the internet
and thats with two different routers

whats the make and models of the routers

is there a modem involved ?
if so make and model

do a power cycle - see below

------------------------------------------------------------------------

How to power cycle

&#8220;power cycle&#8221; process to reboot or reset the modem/router

Switch off all the devices modem, router and computers also unplug their power cables.
Wait at least 1 to 5 minutes. We have found in some instances you need to wait at least 15 minutes
Plug the power cords back in, but don&#8217;t switch them on.
First turn on the modem and then wait for a few minutes for it to settle and all the lights to become stable.
Next switch on the router (if a separate device) and then wait for a few minutes for it to settle and all the lights to become stable.
Now turn on your computer, You should now be able to access the Internet.
------------------------------------------------------------------------
 

3 more replies
Answer Match 48.3%

In the past, I could access my routers set up by typing in 192.168.0.2 as the address in my web browser. Now I am not able to access the set up window. I have connectivity to the internet and everything has been working just fine. I usally go into the configuration to turn on and off the wireless portion of my router. The router is a netgear VPN. Can someone please assit with this issue. Thanks!
 

A:Can't Access Router Configuration

13 more replies
Answer Match 47.88%

Reuel,

Do you have any idea on setting up the Linkys Router with 4 port switch (besfr41)? I have followed the directions in the manual but I get nothing, no connection to the internet. The modem is connected to the router and the router is connected to the pc. Although I am using a straight cad 5 cable between modem & router. Use a crossover cable instead between the DSL modem and router? Any comments would be great.

Thanks
 

A:{Advice Given} - DSL/Router networking configuration

12 more replies
Answer Match 47.88%

Hi, I have the TP-Link wired TL-R600VPN router. I was able to access its configuration page from my PC and set the security so that only the PC's MAC address would be able to access it. Now my PC's monitor died and I tried accessing the router's configuration from my laptop, and obviously the access was denied as the MAC address is different. Is there a way to fix this? Thanks.

A:Unable to access router's configuration

If you have remote desktop setup on that computer you could remote into the the computer without a monitor other than that you may have to reset the router or if you have a computer running linux and you know the mac you could spoof it and logon

6 more replies
Answer Match 47.88%

i have netgear FVS336 dual wanport vpn router. one wan port is connected to my company server through vsat and having static ip and gatway. second wan port is connected to isp dsl modem which is having dynamic ip. now i required configuration to use both wan ports same time. please help me
 

More replies
Answer Match 47.88%

Ok quick question, i currently have 2 Dlink DSL 2640R's networked together and set up correctly, the Master router is assigning DCHP addresses and the secondary is forwarding to the relevant computer thats connected to it.

I have two PC's both connected to the secondary router, which are able to network together and use the master routers internet,

However, my girlfriend is buying a new laptop next week, and wants to be able to stream music from one of my PC's to her Laptop while connected to the Master router (so she isnt affected by any lags due to networking happening between my two pc's i regularly switch files between them, hence the second router)

so 2 questions:
Firstly, am i right in my above statement that if My 2 pc's are transferring via router number 2 router number 1 will serve her with no overlap between the 2?

and Secondly, DCHP is off on the 2nd router, and as far as i can see, the main router see's my pc's and the 2nd router is invisible, so am i right in thinking that her PC will be able to see both my PC's on the 2nd router? or will she just see router number 2? (i read somewhere that some routers see all clients connected to the 2nd router as one IP address and the 2nd router sorts it out when it gets there)
 

A:Solved: Multi Router Configuration

8 more replies
Answer Match 47.88%

hi hope someone can help me.

How can i delete my nat entries where it says create protocol?

I am a beginner at this. I want to be able to make it more secure.

How can i do this?

Can i edit it using notepad and then import it using the browser?

Also my little network has 3 windows xp workstations and have been setup using windows xp networking ie. i created a disk and setup the other workstations on the network. Everything is working ok except for accessing files on the network. It takes about 2-3 minutes to connect to a share on another computer and access the files. Can someone tell my why?

Does the hostname in this firewall have to be the machine the modem/router is connected to?

here is a copy of my firewall

[ env.ini ]
set var="CONF_REGION" value="Australia" set var="CONF_PROVIDER" value="BigPond" set var="CONF_DESCRIPTION" value="BigPond defaults" set var="CONF_SERVICE" value="Router,PPPoA,DHCP,NAT,VPI/V* * CI 8/35" set var="CONF_DATE" value="Configuration modified manually" set var="HOST_SETUP" value="auto" set var="UPGRADE_URL" value="http://www.speedtouch.com/u* * pgrade500.htm" set var="COLUMNS" value="80" set var="ROWS" value="24" set var="SESSIONTIMEOUT" value="120" set var="HOST_MAC_ADDR" value="xxxxxxxxxxxx" set var="HOST_IP_A... Read more

More replies
Answer Match 47.88%

I can't seem to access the routers web configuration page, I get a Gateway Timeout message. I tried rebooting the router, then rebooted my system, but still nothing. It worked fine a few weeks ago. That was the last time I remember using it. I'm not sure what has happened. I checked the TCP/IP properties and everything is set to contain an IP address automatically. Plus in the ipconfig the default gateway is 192.168.0.1

I am running windows XP and my netgear router is PR114

I did look around the site to see if this question was posted before, but I didn't find anything off hand. If this question has been posted before, please post the link.. Thank you..
 

A:Can't access router web configuration page

14 more replies
Answer Match 47.88%

My wireless linksys router is acting up on me again and i'm not sure how to handle this. I copied the error messages exactly as displayed. Sometimes the problem stops after i wait 30min or so but this is happening allot more frequently now.

I started getting these errors in this order

window failed to find domain name prpblems with DNS server
windows confirmed that ''primary DNS server'' is currently online, but is not responding to connection attempts at this time.

This usually means that a firewall is running somewhere between the two computers and is blocking ''domain''. windows has confirmed that windows firewall on this computer is correctly configured to allow this connection. However, a remote firewall might be blocking your connection.

The following policiy might need to be adjusted to allow windows to connect:

Policy provider: windows firewall firewall
filter name: query user

if the policy provider identified is windows firewall ,click for information about adjusting windows firewall settings. If a differnt policy provider has been identified, check the provider's documentation on how to adjust the policy settings.

Reset the network adaptor ''wireless network connection''
resetting the adaptors can sometimes resolve an intermittent problem.
 

A:Linksys router configuration issues

When Windows gives messages like that there are only two choices:

a. laugh; or

b. cry.

The problem goes away sometimes after 30 minutes with you doing nothing, right? Can you still access the router (ping it, or access its config or status pages)? Have you tried a reset or power cycle of the router? If so, does that clear the problem?

If it is a router problem about all you can do is make sure you have the latest firmware; then reset it to factory default settings and reconfigure it. Next step after that is to replace it.
 

1 more replies
Answer Match 47.88%

I've been trying to solve this problem for over 4 months now by myself so any help would be appreciated. I don't like asking without trying to solve and search for this by myself first, but I just can't do it

Setup:
- Desktop Computer (works fine when directly connected)
- Laptop Computer (works fine when directly connected)
- Cable Modem
- Wireless-G Router (Model CWR-854) - Firewall enabled - All wired connections - No wireless enabled

Problems:
1) BitTorrent won't work properly. “Checking for firewall...” just keeps going
2) It won't allow access to internet banking sites completely. Accesses main pages, but times out when trying to log in.
3) Google Videos and YouTube slower.

Notes:
When I disable the firewall on the the Wireless-G Router, everything works fine. It's just the settings on my router firewall which is messing things up.

Attempted Solutions:

For 1) Allowed port 6881 for inbound and outbound TCP access on router firewall - didn't work - tried disabling Automatic port mapping (UPnP) - didn't work

For 2) Allowed port 443 (SSL) for outbound TCP - still didn't work

For 3) Haven't tried anything!
 

A:Configuration on Router Firewall - Painful :(

9 more replies
Answer Match 47.88%

HI GUYS,
I have a serious problem with cisco 2960 router,i am using a dell dimension 3000 running a microsoft windows xp proffessional.ANY HELP IS HIGHLY WELCOMED!
 

A:cisco 2960 router configuration

what problem are you having? Dunno if I can assist, but am curious as to your network setup.
 

3 more replies
Answer Match 47.88%

Attached is a diagram of a network I’m trying to get configured. All devices are on the same subnet.

The Moden/Router “A” is WAN connected to the internet. Its LAN IP address is 10.0.0.1. Its DHCP server function is ON. Its DHCP range is 10.0.0.101 to 10.0.0.199.

Router B’s default address was 192.168.1.1 but I changed it to 10.0.0.2 and turned its DHCP OFF. It is assigned static IP address 10.0.0.2. It is wired LAN to LAN to Router A.

Router C’s default address was 192.168.1.1 but I changed it to 10.0.0.3 and turned its DHCP OFF. It is assigned static IP address 10.0.0.3. It is wired LAN to LAN to Router B.

Four devices connect wirelessly to Router A and do have internet access. One computer connects wirelessly to Router C. That computer has a local USB printer.

I have three network devices that I assigned static IP addresses to so they won’t be changed by Router A’s DHCP service. Two are connected to Router A and one to Router B.

Router C has three Linux computers wired to its LAN ports. One of those computers has two USB hubs wired to it and several USB devices are connected to each hub.

I want to be able to access the internet from any of the computers simultaneously and I need to be able to print to any of the four printers from any of the computers. I also want to be able to access the USB storage devices from any of the computers and access files on any computer from any other computer.

When I connect wirelessly to Router B I do have internet access. Rou... Read more

More replies
Answer Match 47.46%

I apologize if I posted this in the wrong section.

I have been trying to achieve a Remote Desktop Connection with my office PC (Host -- Win XP Pro service pack 3) with my wireless laptop (Client -- Win XP Home) at my house.

The RDC works at my office in the LAN, when I have my laptop connected in the office network. However, from my home's LAN, I cannot access the Host over the Internet (WAN).

I have tried to open port 3389 for the RDC in the PortForwarding section on my Office's D-Link DIR-615 router setup and did the same for my home's belkin 54G router at home, under Virtual Server, in that setup.

Has anyone had this type of problem with Microsoft Remote Desktop?
 

A:Solved: Correct setup of DIR-615 router configuration for RDC

16 more replies
Answer Match 47.46%

I had a couple of guests over and they were having problems getting online (actually they were on for a day but one laptop dropped) the problem was with the guest laptop itself. While troubleshooting we opened the router as an access point. It gave us a new address for configuration but did not get it all down. It is a Belkin Wireless G router and the previous config address was 192.168.2.1 the new one was 192.168. then 2 0r 1 follwoed by three number sequence I believe starting with 2 (I tried 245 and 254). When I right click on my wireless connection icon and go to properties none of the address work some now start with 70. Is the a way to find the address and if not how do I reset my router?
 

A:Solved: A Router Default Configuration Address?

6 more replies
Answer Match 47.46%

Hi,

I have a D-Link Wireless N ADsl2+ 4-Port Wi-Fi router and my PC (running Windows OS) is connected to the router via. LAN cable
Other devices like Laptop, Tablet, etc. are connected to router via. WiFi

My ISP IP address, subnet mark and DNS Server IP address are configured in Router
And also a different DNS Server IP address is configured in Window OS as well in (TCP/IPv4)

I have few basic questions
a) What is the difference between configuring internet settings in Router and internet settings in PC ?
b) If I configure internet settings both in Router and OS, then which internet settings applies or takes precedence ?

Thanks

More replies
Answer Match 47.46%

Hello,

Some of us don't use just a wireless router, but a combination of wireless and wired routers. In such cases the configuration of the devices can be a little tricky. But this thread it will be explained in depth, each step how to set up a wireless access points for laptops

This tutorial is going to explain how to set-up wireless for people who have setups similar to this model:

Modem -> Wired Router -> Wireless Router

Modem -> Wired Router -> Switch -> Wireless Router

***Note, there are pictures at the bottom of this post, use those for reference when going through this guide***

Supplies:

- Wireless router / power cord
- An ethernet cable to go from the router to the computer we'll be working with
- Oh, a computer with Internet Explorer or Firefox, no chrome yet lol

Step 1: Getting everything ready

- Take the wireless router, plug in the power, and take an ethernet cable from the back of the wireless router ***NOT THE INTERNET / WAN PORT but any port labled [1,2,3,4]*** plug the other end into the computer or laptop

- Now, once the laptop is booted up make sure its connected to the router
WIRED not WIRELESSLY

- Open up Internet Explorer or Firefox
- in the address bar type in the default router IP address which for dlink's is 192.168.0.1 for linksys products its usually 192.168.1.1 and hit enter
- if prompted for a username and password:
- dlink: username: admin password: blank
- linkys: username: admin password: admin

Step 2: Wirele... Read more

A:Wireless Router Configuration as a Access Point

I'm guessing its not too useful or it needs to be revised lol

5 more replies
Answer Match 47.46%

OK, I'll give a brief overview of what I'm working with and then describe my problem. I have a relatively new notebook (bought it about 2 months ago, I wouldn't think the exact specs are necessary but if they are let me know), a DSL connection and I have a Linksys Wireless-G router.

I've attempted to play two games online with a friend (Age of Empires 3 and Diablo 2), both of which resulted in nothing by headaches. In both games we attempted to directly connect to each other via IP. He also has a notebook and is using a wireless router. We've tried it both ways; me trying to connect to him and vice versa, same problem both times.

Now, I don't know a whole lot of anything about networking and routers and the such, but I'll put in what I do know. When I try hosting a Direct IP game, both games listed an IP at the top of the screen, but it wasn't my IP, it was what I think is called the local IP? It's 192.168.1.1; now I know that's the address to the router and if I type that in my browser address bar I can access the router's configuration and all that good stuff. I also noticed that if i go to that address one of the options under the router configuration is "Applications and Gaming". When I go there it lists a bunch of stuff about opening ports and triggering ports and some other stuff that I've never heard of.

I've talked to a few people and they tell me that I would need to open certain ports and... Read more

A:Online Gaming/Router Configuration Problems

7 more replies
Answer Match 47.46%

hello guys,

good day! please i need your help on what to do's regarding wrh54g client configuration. i been setting up today the point of access for its secured network mode with WPA shared key on XP-SP3. tried successfully on a client with windows7 lappy, but then my problem was that my boss want me to set it on a manual mode. i mean, he wanted it that everytime he disconnect the wireless and decide to connect again later he likes to input again the password. but as ive see it everytime i tried to reconnect, the password is automatically inputted already and ready to connect. not unless u click the wpa box and the password will be deleted. boss wanted this kind of setup for security purposes. i hope u can help me on this matter. my other options also were not successful.

all comment and help will be highly appreciated.

regards,

twinx

A:[SOLVED] please help on WRH54G router client configuration..

Let me say this much. If that were the case with my wireless network, I would be entering my 64 character passkey every time I connected to my wireless network. I could just copy and paste it from a text file, but then what is the point of doing that over just letting the computer save it for me? If your boss wants to make sure his wireless security is strong, his efforts are much better spent doing what I have done by going to the website linked below, copying the "64 random hexadecimal characters (0-9 and A-F)", while using either WPA, or WPA2. The kind of authentication I think he is getting at, is something a radius server would be better at providing, provided your computers were part of a domain.

https://www.grc.com/passwords.htm

In Windows 7, I know it is possible to have it not remember your passkey provided that you do not check the checkbox during the connection setup. My memory is a little off with XP. Does it provide something similar?

5 more replies
Answer Match 47.46%

I am using Tenda wifi router. It has a problem, it is that it need configuration every time when I start my laptop or connecting with any mobile device. What is the problem with that?
 

A:Tenda wifi router need configuration every time

The Tenda wifi router's internal battery may be dead
 

1 more replies
Answer Match 47.46%

At work I am trying to figure out how to configure out wireless router. What I need to be able to do is to have people who use wifi to be able to also connect to our office file server (which will have shared printers so we can monitor usage amongst different departments). How can I do this? 90% of the office connects through wires using a static ip. Would I need to configure the router with a static ip as well? If so, would the wifi laptops need to have a static ip as well?
 

A:Wireless router configuration for use with file server

If there is a DHCP server on your office network, the following configuration for the router and allow the connections you seek. You could also use a wireless bridge if you haven't purchased yet.
Connecting two (or more) SOHO broadband routers together.

Configure the IP address of the secondary router(s) to be in the same subnet as the primary router, but out of the range of the DHCP server in the primary router. For instance DHCP server addresses 192.168.0.2 through 192.168.0.100, I'd assign the secondary router 192.168.0.254 as it's IP address, 192.168.0.253 for another router, etc.

Note: Do this first, as you will have to reboot the computer to connect to the router again for the remaining changes.

Disable the DHCP server in the secondary router.

Setup the wireless section just the way you would if it was the primary router, channels, encryption, etc.

Connect from the primary router's LAN port to one of the LAN ports on the secondary router. If there is no uplink port and neither of the routers have auto-sensing ports, use a cross-over cable. Leave the WAN port unconnected!

This procedure bypasses the routing function (NAT layer) and configures the router as a switch (or wireless access point for wireless routers).
 

1 more replies
Answer Match 47.46%

I'm trying to run a server for a java application called mekwars. The program needs ports 2347 and 4867 open.

I have obtained an ip address from my ISP and registered with dyndns. I can ping my public ip address (my router)

I can access my server from any other computer in the LAN. My router is a Zyxel p660hn-T1a. I have configured port forwarding of both ports to my server.

I have disabled the firewall in the router and restarted it.

My server is running CentOS 6. I have opened the ports in the server iptables, I don't think this is the issue as I can connect from my lan to the server.

When I try to connect (from within my lan) to the public ip address of my server the program tells me it cannot find the server. I can't telnet to port 2347 and nmap tells me that the only ports that are open are 22, 23 and 80 ( I believe this are open by default on the router to allow remote management).

I can telnet from the lan. My networking isn't great and I'm used to having an "ip passthrough" option on the router to assign to my server. I do have it set as the default router in port-forwarding so I had hoped this would be a similiar option.

I've a funny feeling I'll have to telnet to the router to take care of some hidden options but I'm posting here first hoping some network guru will be able to say "Ah I ran into this problem back in 19dickity6... "

Can anyone give me any suggestions as to where I'm going wron... Read more

A:Help needed with router configuration for home server

When I try to connect (from within my lan) to the public ip address of my server the program tells me it cannot find the server.Click to expand...

You mean the public (WAN) IP address of the router, right? Some routers will "loop back" the way you want it to and others will not.
 

2 more replies
Answer Match 46.62%

Hi

I have a Dell 2350 wireless router which I have happily used in the UK for the last 12 months.

I have just relocated to Australia and am having real problems reconfiguring using the CD driver.

It acknowledges that there is an internet connection direct via the ethernet cable into the PC; following the steps the internet light is then on; then there are lots of flashing lights whilst it tries to configure; LAN port light flashes; but configuration fails; and there is no internet availability.

Please help if you can, I am at my wits end.

Thanks
 

A:Dell wireless router configuration / connectivity problem

I have had the same router for years, and in my personal and professional opinion, can it and buy a better one, it never worked well and was always laggy. but otherwise reset it to factory settings and begin setup from the ground up.
 

1 more replies
Answer Match 46.62%

Our ISP provided a DSL modem/router (Netopia) that I connected to the Netgear wireless router with dd-wrt flashed. All I've done so far is connected the two. I have a connection, but I want to know if it's possible or advisable to configure everything from the Netgear router. But following the instructions herehttp://www.dd-wrt.com/wiki/index.php/Wireless_Access_Point, it seems I have to configure DNS and such using the Netopia router. I don't have a full grasp on how to use them together the correct way - like using the Netopia as an ethernet bridge. Thank you,

Brandon

Sent from my Motorola Electrify using Tapatalk 2
 

A:Netgear WNR2000 Router behind Netopia 2241N Configuration

6 more replies
Answer Match 46.62%

Hi everyone,

I recently tried setting up a Buffalo WHR-G54s router on my desktop (which has Windows XP on it) so that I can access the internet with my laptop as well. I have no problems accessing the internet on my desktop after connecting everything, but I can't access the configuration page to set a password and change the SSID.

The default IP address of the router config is supposedly 192.168.11.1. However, when I run ipconfig /all, the default gateway is listed as 67.186.14.1. This IP address also pings successfully. Nowhere is 192.168.11.1 seen after running ipconfig /all.

When I try accessing either of these IP addresses in IE or Firefox, nothing happens. I even temporarily disabled all PopUp Blockers and shields (as far as I can tell) to see if that would help as well. But nothing seems to work. Anyone have any ideas?

Thanks!!!!
 

A:Cannot access configuration page of Buffalo Router WHR-G54s

12 more replies
Answer Match 46.62%

I was a bit of a loss and maybe it's because I have been out of the game for a long time but I came across a disturbing development. I call century link because my router was not connecting at the proper speed of 7 mbps. That problem was easily remedied over the phone but the lady said she could see several devices connected. This lost me a bit because I have a double router configuration. The Actiontech PK5000 i turned into nothing more that an internet modem. I disabled the DHCP and configured my Linksys E1200 for all the internal DHCP so there is only one cable going to the PK5000. I should technically speaking look like one user on there network with natural protection from the second router. I may be kidding myself or man I'm getting old but if someone can tell me how that works it would be fun to know and what would even be funner to know is how to stop it!!!!!!!!

A:Interal network security with dual router configuration

Erm. Could you clarify what exactly you want? Your message is very... convoluted.

1 more replies
Answer Match 46.62%

I have the following ethernet network configuration:

WAN

Router 1​
LAN
WAN

Router 2​
LAN
Computers
ISP Assigned Static IP
(W.X.Y.Z)
Static IP (A.B.C.1)
Static IP (A.B.C.2)
Static IP (P.Q.R.1)
DHCP Clients (P.Q.R.*)
ISP&#8217;s Gateway
No DHCP
Gateway = router 1 (A.B.C.1)
DHCP Server
Gateway = Router 2
ISP&#8217;s DNS

DNS = router 1 (A.B.C.1)

DNS = Router 2
One of my computers is set up as a web server and which I can access it from outside my network, but from inside my computer LAN, I cannot acccess it.

Can someone help me on how to configure the Router 2 DNS so that behind the router2, my website URL resolves to the local web server IP address?

Thanks in advance,
Moiz Tankiwala
 

A:Help needed for Router DNS configuration - Unable to access website from LAN

I ran into the same problem and had to use a proxy service so my
router didn't see it as a local connection attempt.
http://anon.inf.tu-dresden.de/index_en.html
 

3 more replies
Answer Match 46.62%

My computer is connected wirelessly to a Linksys router, which is connected to the internet through a modem/router that my ISP provided. When I enter 192.168.0.1, I am taken to the configuration page for my ISP's router. How do I access the Linksys router's configuration page?

I have tried all sorts of combinations of 192.168.x.x, but nothing has worked. Is there a way to figure out the address the Linksys router's configuration page? ...or is there a reason I am unable to access it?
 

A:Solved: Trouble accessing router's configuration page

9 more replies
Answer Match 46.62%

I have a Netgear MR814 router. I used to be able to access the configuration screen by entering 192.168.0.1 in the address bar and then inputting the default username (admin) and password (password).

That stopped working a while ago. I decided to reset the router to its default setting by pressing and holding the reset button on the unit. It didn't seem to work. I can still access the internet, but I can't get to the configuration screen. Sometimes it says that the server is busy without giving me the option to enter a username and password. Other times it does ask for the username and password. When I input them, it seems like it is going to work and the screen starts to load. Then it asks me enter the username and password again.

Can anyone help.

BTW the ISP is Comcast
 

A:Netgear MR814 Router can't access configuration screens

try resetting again, but hold the reset button in while unplugging, wait, and then re plugging the power supply to the router.
if that doesn't work, dropkick the router across the room. When I had this problem, my roommate did that (to my horror), and everything magically work, and has been working ever since.
 

1 more replies
Answer Match 46.2%

Components involved in network
Dell Dimension 3000 Tower OS Win XP SP 2
Dynex Wireless G Router
HP Laserjet 4050 TN
What I'm trying to do.

Get the wireless router to recognize the Laserjet and assign it an IP address though DCHP.
The laser jet was originally configured on a physical Net Gear Route, thus it has RJ45 ehternet connection. When I connect the laser jet, Dell PC and the Dynex Wireless Router. The wireless network works fine as far as a laptop accessing the network, BUT the router does not recognize the laserjet and does not assign it an ip address. The laser jet had an static address with its old configuration. How do I get the router's DHCP to recognize the laserjet and assigne it an IP address? Any ideas or ways to configure the Laserjet to accept an IP assignment or lease?
 

A:Solved: HP Laser Jet 4050 configuration with Dynex wireless G Router

14 more replies
Answer Match 46.2%

Hi Guys (and Gals?)

SUMMARY:
I want to add a second wireless router to my existing home network. Also I plan to upgrade to a "smart" (internet-connected) TV within the next year so I'm trying to plan ahead. I have a decent-sized house with many THICK walls (no drywall here!). Tech-oriented family of 4.

Other details:

1. Existing router is Linksys E3000 and has served well.

2. Four endusers in house: all technophiles and heavy data users, often simultaneously.
-- Son connects his self-built gaming monster machine via Ethernet. Hard core gamer thus streaming is critical. Also art student but I'd say his build has accommodated those needs well.
-- Hubby laptop PC and tablet and phone; streaming to tablet is critical, esp. from upper floor bedroom.
-- Daughter phone and laptop; streams to both, often from upper floor bedroom.
-- Yours truly mom, (and network admin)... heavy reliance on self-built desktop (Win 8.1), Asus laptop (Win 7), tablet, smartphone (often all simultaneously), streaming, bluetooth(s) (plural?) , whatever else I come up with.

3. 3 TV's that use the cable modem, but I plan (hope!) to swap one of these in next year to a smart TV (love the Roku I use now, which of course connects to my wonderful e3000 router) The TV to swap is on main floor, front of house.

4. Wiring: I live in an old house; translate: brick exterior (awesome), very thick plaster walls interior (they don't make em like this anymore, sooo cool), small-ish ro... Read more

A:Please advise on best router to add and configuration for house of heavy data users

Are you concerned about 'ac' vs. 'n' because of file copies (or streaming) on your LAN? Or is your internet access faster than you can handle with 'n' Wi-Fi?

If you use a SOHO router as wireless access point following is the complete procedure.

JohnWill's procedure (Aug. 30, 2008) for configuring a secondary router as a switch and, optionally, wireless access point follows.

Connecting two (or more) SOHO broadband routers together.

Note: The "primary" router can be an actual router, a software gateway like Microsoft Internet Connection Sharing, or a server connection that has the capability to supply more than one IP address using DHCP server capability. No changes are made to the primary "router" configuration.

Configure the IP address of the secondary router(s) to be in the same subnet as the primary router, but out of the range of the DHCP server in the primary router. For instance DHCP server addresses 192.168.0.2 through 192.168.0.100, I'd assign the secondary router 192.168.0.254 as it's IP address, 192.168.0.253 for another router, etc.

Note: Do this first, as you will have to reboot the computer to connect to the router again for the remaining changes.

Disable the DHCP server in the secondary router.

Setup the wireless section just the way you would if it was the primary router, channels, encryption, etc.

Connect from the primary router's LAN port to one of the LAN ports on the secondary rou... Read more

3 more replies
Answer Match 46.2%

Hi, I'm having a problem setting up my router. Whenever I connect my router to my modem, I get the error "Local Area Connection 2 doesn't have a valid IP Configuration."

How can I fix this?

This error goes away when I connect just my modem to my computer.

I know the router isn't broken, and I'm sure I have all the cables plugged in correctly.

Router Model: Netgear WNR2000

OS: Windows 7

Thanks for any help!

I've been trying to fix this for a week now!
 

A:Router Help! Local Area Connection Doesn't Have a Valid IP Configuration.

The following procedure should get you a connection with any broadband modem that is configured to use DHCP for the router connection, such as cable modems, and many DSL modems. If you require PPPoE configuration for the DSL modem, that will have to be configured to match the ISP requirements.

Note that the wireless encryption and channel selection will have to be done after the basic wired connection is established, the first step is to get wired connections working.

Reset the router to factory defaults by holding the reset button down for 15 seconds with power on.
Turn off everything, the modem, router, computer.
Connect the modem to the router's WAN/Internet port.
Connect the computer to one of the router's LAN/Network ports.
Turn on the modem, wait for a steady connect light.
Turn on the router, wait for two minutes.
Boot the computer.

When the computer is completely booted, let's see this.

Hold the Windows key and press R, then type CMD (COMMAND for W98/WME) to open a command prompt:

NOTE: For the items below in red surrounded with < >, see comments below for the actual information content, they are value substitutions from the previous command output!

In the command prompt window that opens, type type the following commands one at a time, followed by the Enter key:

IPCONFIG /ALL

PING <computer_IP_address>

PING <default_gateway_address>

PING <dns_servers>

PING 206.190.60.37

PING yahoo.com

Right click in the command ... Read more

1 more replies
Answer Match 46.2%

my internet connection uses PPPoE to connect to the internet. i'm trying to set up the router for this configuration but it does not work. if there is anything else i need to post up pls tell me...help!!
 

A:Configuration problem for belkin adsl2+ modem with wireless router

the MODEM uses PPPoE, the router should not. the ADSL modem will hold the connection
regardless of anything being active on your router or systems, so imo, the router
should not be configured for PPPoE.
 

1 more replies
Answer Match 45.78%

I have my main computer with the following setup

Windows Vista connected to the router then to the modem in Bridge Mode (so that I can use NAT1 with my PS3), thus internet works fine for both, my Main Comp (Desktop) using PPPoe and PS3 using a wireless connection between my router but also through PPPoe.

However, in terms of my secondary computer (Desktop), I have a USB Wireless Adapter, but I do not seem to be able to find the configuration for going on to the internet through the router but to use PPPoe.

The following are my products

Router - D-Link DIR-625
Adapter - D-Link USB Wireless Adapter DWL-G122
Modem - SpeedStream 5200

Thanks
 

A:Solved: Modem Bridge Mode + Router + USB Wireless Adapter Configuration

I'm a bit confused. If you're connecting PPPoE with two devices, that indicates you have two modems, which sure doesn't sound right. What are you really doing here?
 

3 more replies
Answer Match 45.78%

Alright, heres the setup:

(1) DSL Modem
(1) WRT54G Router
(1) Desktop WinXP Pro SP2 machine, hardwired to router
(2) WinXP Pro SP2 laptops, wireless - one with built-in wireless, one with a Linksys WPC11 Instant Wireless Network Adapter, version 3.
(1) WinXP Media Center SP2 laptop, wireless
(1) Ubuntu Personal Edition - "Feisty Fawn" 7.04 laptop, wireless

The router has been set up to use WPA-TKIP encryption on channel 6 with an always-on PPPoE connection; it also has an IP of http://192.168.2.1 to avoid an IP conflict with the DSL Modem. DHCP Server is enabled with default settings, MAC Address Clone is disabled, and Operating Mode is set to Gateway. Access is set to allow both B and G, as one of the WinXP Pro laptops is an older model Toshiba that only recognizes the B protocol (that's the one with the WPC11 card).

Here's the problem:

Initially, the setup works flawlessly. All computers are able to see the SSID, connect to the network, and connect to the internet. The connection is fine, doesn't slow down, and is overall pretty healthy. All computers are able to access http://192.168.2.1, and are prompted with the username/password prompt, can change settings, port forwarding, etc.

Now, wait a few days. Usually about a week.

First, the Ubuntu laptop starts to get spotty with it's connection to the internet. After about 10 minutes, the connection to the network starts to fail. Sometimes it will see the SSID, sometimes it won't - and ... Read more

A:Linksys WRT45G > Unable to access router configuration, whole network degrades

I'd first upgrade to the latest firmware, and reset to factory defaults and reconfigure. If that fails, I'd have to suspect an issue with the router.

Many times heavy use of P2P does this to SOHO routers, something to consider.
 

3 more replies
Answer Match 43.68%

The rest fo the error message says- "Failed to read configuration file. Please contact system administrator"
I have just R and R'd Firefox and I'm still getting this error message. It won't run now and now I see just how horrible IE is in XP,since I'm forced to use it now....sob
Please Help!!

A:Firefox won't startup-Error message says "Configuration error"

Only an idea!!!!  Not sure but it may be the newer FF may not run well on XP, you could experiment by down loading and older version.
 
Just checked I may be right check the link below!
 
https://support.mozilla.org/en-US/kb/firefox-no-longer-works-some-versions-windows-xp

7 more replies
Answer Match 42%

Ok, I have Windstream DSL that connects through a Siemens 4200 modem that goes into my linksys wrt54g wireless router. So how exactly do I access the modem, if when I type in 192.168.1.1 goes to the router. How can I access the modem to port foward? The only current way I can get to access settings on my modem is to go to Windstream.net and go to configurations in the top right. From there I can access the modem. Is there any way to port foward with this modem?
 

A:[Siemens] Accessing Siemens 4200 configuration page with a Linksys router

11 more replies
Answer Match 42%

These seem like they may be related, but when i go to "Run" and type in "ipconfig" it closes instantly. Also, when I type in my IP in my browser to go to the router config it loads fine, but clicking anything results in a 404 error, could anyone tell me what's going on?

*EDIT*

Forgot to mention, I'm using Windows XP. If any other info would be useful let me know.
 

A:Solved: Problem with router configuration and "ipconfig"

6 more replies
Answer Match 41.58%

I have an HP pavilion A6303w,every I tried to booted it.It always come with a message stated configuration error code purple...It's a windows vista desktop..I even try to change the windows vista to windows xp..As soon as I insert the cd in the drive,it started downloading just fine.As soon as it started to set up the windows it stop..And come back with that message configuration error..Please help thanks.
 

A:Configuration error.

I have never seen something give an error message "code purple". Maybe it is a BIOS error message? Do you see that "code purple" as you boot the machine or would Windows start running and give you that error ?
 

2 more replies
Answer Match 41.58%

When I try to run SPSS which I recently installed it receive an error message stating that the application can't run because of a configuration error. Can any one help with this? My professor was telling me what that meant and honestly really freaked me out.

A:Configuration Error

It simply means that it didn't install properly/completely...for whatever reason. It's not set up properly for use.Program settings are configured (usually) after install...or using the default settings.Google LinksLouis

1 more replies
Answer Match 41.58%

using windows xp on my presario sr1103wm i ran the recovery in the pc repair program and after it restarted all i get is this error message has detected a configuration error (code purple) and the computer is non-responsive help
 

More replies
Answer Match 41.58%

when i try to start a game it says it cannot
open the configuration
 

More replies
Answer Match 41.58%

Hi

I just re-installed windows XP pro on my dell pc,and when i come to switch on the machine ,i get a message before startup saying invalid configuration information.
I have to wait and then it starts up. It has also reset the time and date.

The battery inside was fine before i wiped it-could it be the BIOS ?

Any help would be very welcome
Thank You
 

More replies
Answer Match 41.58%

Hello,

This is the first time here for me, have searched the forum and could not find an answer to solve my problem, maybe I have overlooked it.

Here is the problem, when I turn my computer on I get this error message.

CPU = Intel (R) Pentium (R) 4 CPU 2.00GHz
639K System Ram Passed
638M Extended RAM Passed
512k Cache SRAM Passed
System BIOS shadowed
Video BIOS shadowed
ATAPI CD-ROM: Sony DVD RW DRU-720A
ATAPI CD-ROM: HL-DT-STDVD-ROM GDR8160B
Mouse initialized
ERROR
0162: Configuration Error - Default configuration used

Press F1 for Setup
If someone could give me some guidance it would be greatly appreciated, the operating system is Windows XP Pro.

Thank you
wicewater
 

A:Configuration Error

7 more replies
Answer Match 41.16%

I got this error after I did a Compaq System Recovery.
Your system has detected a configuration error. Please report this error to Customer Care using the phone number found in the Warranty and Support Guide that came with your PC. Unless corrected, this error will prevent your PC from operating properly. Turn off your PC by pressing and holding the Power button. After a few seconds your PC will automatically turn off. (Code Purple)
Help!
 

More replies
Answer Match 41.16%

Immediately after upgrading to IE8, a Wireless Configuration error message began appearing and will not close even when I reboot my Acer Aspire 5600. It reads as follows:

Incorrect MFC Dll version installed on system, minimum requirement is MFC SP4 dll.

I located an answer from Dell for their computers in these Forums, but can't find anything here for Acer. Any help would be appreciated.

Laurie

A:Wireless Configuration Error

do you have a service running called Broadcom Wireless LAN Tray Service
control panel> admin tools> servive

3 more replies
Answer Match 41.16%

System details;
OS Windows 7HP 64bit
CPU AMD Phenom II Quad
Motherboard ASUS M4A79-T Deluxe 790FX
Memory 12BG Corsair XMS3
Video card Sapphire ATI Radeon HD 4890
Boot disk C:\ Samsung Spinpoint 1TB 7200 SATA II 32MB
Problem;
Tried to update Snagit 11 (build 207) to version 12.2.2 (build 2107) but when trying to install the update I get snagitup.exe-Configureation paser error, error parsing C:Windows|Microsoft.Net\Framework\v4.0.30319\config\machine.config Paser returned error 0xC00CE508
 
Would greatly appreciate any help 

A:Configuration Parser Error

Worth a look, Configuration Parser Error .
 
Louis

5 more replies
Answer Match 41.16%

Recently I've been getting a popup message at boot: Error detected retrieving default

configuration DEFAULT.ALC. I close the window and everything seems to run fine.
Anyone know what that's about or how to fix it??

Machine: Esystems
OS: WindowsXP Home
RAM: 1.5GB
Drive: 120GB
 

More replies
Answer Match 41.16%

Hi there guys.

One of my applications, Microsoft Flight Simulator X was working normally for awhile until I encountered a problem where it says the application could not start because its side by side configuration is incorrect. I cleaned everything up by doing "sfc /scannow" in Command Prompt and it solved the problem.

However, when I tried to open up Microsoft Flight Simulator for the second time, the error occurred again. Can I please help some advice on how to stop this re-occurring problem?

Thanks,
Jozef

A:Sidebyside Configuration Error- NEED HELP!

Welcome
It will take a little while, but I will refer this to our forum specialist in this area.

9 more replies
Answer Match 41.16%

I have Windows Me and when i try to boot up i get this error.


Cannot find System.ini.

Boot with emergency boot disc and type scanreg/restore

WHAT Do i do?? I dont have the boot disc. I have another computer with xp and if i need to download a file i can. Any help?
 

A:Registry Configuration error

Take your system to someone who can test your hard drive and reload Windows Me for you
 

2 more replies
Answer Match 41.16%

I have tried everything but everytime I boot up my computer I get this hardware configuration error any suggestions on what I should or can do?
 

A:Hardware configuration error

What operating system do you use, and what is the brand and model, or configuration of your computer. What tasks are you running when you get the hardware configuration error... or does it even boot.
Tell us as much as you can, so we can imagine what you are up against.
 

3 more replies
Answer Match 41.16%

I'm on ADSL Zoom X3 modem connected to my PC with No other Router connected

when I used a bittorrent for the 1st time (Azureus), I got NAT error problems, this happened to everything I tried.
It tells me I have no remote access & icons stay on yellow?
I checked all the wizard configurations & whatnot, they all told me I have a NAT error

I just want to know if theres anything I can do? because when I switched to my AOL 56k connection, the NAT error was not present there
SO is my NAT messed up or not set up correctly???

I don't have a router so I can't open any ports only on it,
I'm only with my DSL modem, so I went to my DSL setup page

I went to the NAT CONFIGURATION OPTIONS
the screen had this info:

NAT : Enable
Mode: Dynamic

Session: blank (no other options listed but can be typed on)
User IP: blank (no other options listed but can be typed on)
Action: add (& another option for delete)

Number | Session | Name | User IP
# of NAT configurations: 0
I tried switching to disable NAT!
the description makes it seem like hackers can get to my IP & whatnot without it, but I tried anyways, BUT I could not connect to the net anymore after that, I had to re-enable it.

All I know on on Azureus is that in options it states 6881 as the incoming TCP listing port.
there is no Session or User IP info there to find & typing 6881 on User IP just tells me it's an inncorrect IP
can anyone help?
anyone with any knowledge of this??
is it poss... Read more

A:can ANYONE help me with a NAT error/configuration problem??

the other options on my dsl setup page other then NAT are:

WAN settings
LAN settings
NAT
Virtual Server
DMZ
DNS
ADSL Configuration
Route Table
Misc Configurations
Bridge Filtering
RlP Configuration

are any of those helpful to open the 6881 port?
 

1 more replies
Answer Match 41.16%

i had the sbc yahoo utilities on my comp with the browser and chat and little things like that and then i uninstalled it and tried to reinstall it and now i get an error half way through saying can not configure to my comp??? howcan i fix this???
Thanks
 

More replies
Answer Match 41.16%

ok heres the prob...
today my nephew was playing sims 2 and while he was playing he hit the shelf the tower was on..it fell less than 2 feet and not very hard since the cords slowed its fall...
now when i go to restart it i get this errors:

0162 configuration error
no dhcp or proxydhcp offers were recieved
1962 : no operating system found

im not sure what has happened or what I need to do now.
I was reading online and it said run setup but not sure what that meant.
 

A:0162 configuration error

Run setup probably means run Windows setup. But i think i may know what is wrong. Can you check the hard disk IDE cable, make sure both connections at either end of the cable are securely fixed into their sockets
 

2 more replies
Answer Match 41.16%

I'm having this issue

TCServer.ext - Configuration Error

Unable to load Jit Compiler (MSCORJIT.DLL)
File may be missing or corrupt
Please check your setup or rerun setup!

Basically when I did a google search I came up with this patch for what everyone says is a memory leak.

http://www.microsoft.com/downloads/d...displaylang=en

This didn't solve my issue.
The actual issue is that this error comes up as soon as I log into windows and either freezes me straight away or resterts.


- Version of the OS. XP Tablet Edition
- Security Patches - Unknown. I can't use the tablet long enough to check
- If the OS produces an error, either upload a screenshot of the error message (ALT+PrtScrn), or literally quote See above
- Were there recent crashes that could have caused this problem?Unknown
- Did you install new software recently? If this is the case: Which software? (Brand, version, build)Unknown
- Did you do any of the following:
- Run a scan with an updated anti-virus program?No, can't
- Run a scan with an updated anti-Trojan program?No, can't
- Run a scan with an updated root kit detection program? (This only for Windows NT, W2K and newer!)No, can't
- Run anti-spyware scans with at least two freshly updated anti-spyware programs? No, can't
If any of these program found something, provide us with the information on what it/they found. N/A

More replies
Answer Match 41.16%

I'm using Win 7 ultimate 32 bit. I've a problem when configure DNS. I enter Local Area Connection Properties then click on Internet Protocol Version 4 but it show a window and disappear.

It like this video:

Who can help me, please?

A:Error! can not set up TCP/IP configuration on Win 7 ultimate

Can you access it in safe mode?

9 more replies
Answer Match 41.16%

Hello there. I hope I have posted this message in the right area. This morning I fired up my pc to find an error greeting me. It was that windows was missing a configuration file. I rebooted a couple of times then it came back up.

Once it did tho, it went through reloading all my hardware. Everything was fine so I thought. I then realized there was no sound. Xp is showing the Realtek onboard sound card there, indicating under Audio Devices, Properties that "This device is working properly" and "Driver is enabled but has not been started". However, under the main Volume tab it shows "No Audio Device".

I have verified under Services that Windows Audio is started and running (set to 'Automatic'). I have attempted to remove and resintall the device, tried alternate drivers, all to no avail. Any suggestions or recommendations on how to proceed would be so greatly appreciated!
 

A:Configuration error...now no sound.

7 more replies
Answer Match 41.16%

Hey there,

I'm on windows XP

when it comes to installing many new applications (not pirated or anything) I get this error

"C:\filelocation\program.exe

This application has failed to start because the application configuration is incorrect. Reinstalling the application may fix this problem."

It has happened both for the new MSN (Im stuck using windows messenger) and Ableton Live 8.03

I've obviously tried reinstalling a whole bunch of times, but no luck. Is my only option here reformat, could it be something viral? Or something more simple (i hope!)

Cheers and thanks a lot
 

A:Application Configuration error (XP)

8 more replies
Answer Match 41.16%

I have Windows Me and when i try to boot up i get this error.


Cannot find System.ini.

Boot with emergency boot disc and type scanreg/restore

WHAT Do i do?? I dont have the boot disc. I have another computer with xp and if i need to download a file i can. Any help?
Edit/Delete Message
 

A:Registry Configuration error

Yes this was copied from another thread. I posted it in the wrong place
 

2 more replies
Answer Match 41.16%

Friend has and HP a535w that is producing an error, machine boots up until the XP media center splash screen and then an error box appears:System Configuration ErrorThe system has detected a configuration error. Please report this error to customer care using the phone number found in the Warranty and support guide that came with your PC. Unless corrected this error will prevent your PC form operating properly.Turn off your PC by pressing and holding the power button. After a few seconds your PC will automatically turn off. (Code Purple).'i searched google and the only thing i could find http://www.resellerratings.com/forum/tech-...ode-purple.htmlwas that this had something to do with "tattooing" the recover to the motherboard, and a workaround was to attach the HDD to a usable system andopen up C:\hp\bin\ConfigCheck\cfgchk.bat with notepad and modify the section that checks to see if the hard drive is tattoo'd to have it not bother checking at all. (although the hard drive will be running as slave so replace the C:\ with whatever drive letter Windows assigns it) The line to remove is: "python c:\hp\bin\ConfigCheck\run.py". This worked great for me and I hope it helps anyone else who comes along this thread as an alternative to dealing with tattoo'ing the motherboard or hard drive. i did this and cannot find the .bat file, that path does not exist.this machine is out of warranty and we do not want... Read more

A:HP system configuration error

http://www.techimo.com/forum/applications-...ode-purple.htmla couple of pages into this thread seem to have several fixes.

4 more replies
Answer Match 40.74%

I recently tried to turn on my pc and the boot manager screen is up and no matter what i do for several days now i cant get past this screen someone please help ive tried everything

A:Boot Configuration Error 0xc000000d

See Troubleshooting Windows 7 Failure to Boot

3 more replies