Tech Problem Aggregator

WRT160n v3 Power/ Adapter Problem

Q: WRT160n v3 Power/ Adapter Problem

Hi,

I bought a Linksys WRT160n v3 wireless router sometime back. I had considerable trouble in just turning it on. There is an FAQ article by CISCO which says that you have to first plug in the adapter in a power outlet and ONLY afterwards plug the other end into the wireless router. I tried that; it works most of the time (>90%) but not always!! The wireless router turns on only by hit and trial in 10% of the cases.

Adding to my woes is that there was a power cut yesterday and after that I am unable to power on this wireless router at all. I have been fiddling with it for hours but with no luck. Is the wireless router dead? Is there anything that I can do to verify the adapter/ router's sanity?

Is anyone facing similar problem?

A: WRT160n v3 Power/ Adapter Problem

6 more replies
Answer Match 61.74%

Hello,
My Cisco Wireless router (WRT160N) doesn't automatically reconnect after a power outage. This is a huge issue because my router is connected to my VOIP. If a power outage occurs then I will not have phone connection. The only way to fix this is to mannually power cycle the router after the power outage, but someone needs to be at home to do this. Is there any way to enable some type of auto-connect after a power outage?

Thank you very much!
Tony
 

More replies
Answer Match 57.54%

Hi all, I have a Linksys WRT160N V2. It is currently hooked up through another router but was originally hooked up directly to the modem. It worked for a couple months and then stopped. I think someone in my family might have inadvertently changed the settings but have reset to default with both the button on the back and the option by typing in ip in address bar and going to reset.

On the computers I am trying to connect, 1 via wifi and 1 by ethernet cord, are both running Windows 7 64 bit. (6.1, build 7600).

When connected I get the yellow ! and this is screen shot of other stuff I could think of.

If anyone could help, Ill get any info needed, I just hate having a router for less then 3 months and it being useless now, especially when I need a second.
 

A:Linksys WRT160N V2 Problem

12 more replies
Answer Match 56.28%

I have an Acer 3690 laptop. Recently the original power adapter went bad. I went to a local computer company and had them order me a new one. The day I got it home and plugged it in the adapter smoked and the plastic split showing bare wires. We returned the adapter and they exchanged it for another one. The day we took the new one home it did the same thing. Any ideas what could be the problem???
 

A:Power Adapter Problem

11 more replies
Answer Match 56.28%

Hi everyone.

I know that this is not really entirely related to a Windows 7 computer and especially to these forums, but I really need some advice on this and it would be great if anyone who has experience in voltage, amps and safety for laptop power adapters would be perfect.

My friend has just traveled down to my house for a week but has foolishly forgot his plug for the power socket on his power adapter. He uses this for his computer. Again unrelated becuase it is an Apple 45W MagSafe2 adapter.

So I was wondering if he could simply use a cord like this one below to plug into the adapter?
The black cord is 2.5A 250V~

The adapter is 100-240V~ 1A

These are both for input.

Any help would be greatly appreciated .

A:Power Adapter Problem

That white 'thing' appears to be for an Apple Macintosh MacBook/MacBook Pro [I have a MacBook Pro] and you might not be able use the black cord due to fit, the V-shaped notch in the black plug would have to let it be inserted. But it probably won't hurt to try as it's still a 110/120Volt source.

The MacBook power adapter also came with a piece that replaced that cord and has the prongs to plug directly into a wall socket/extension cord, maybe it's in his Notebook bag.

3 more replies
Answer Match 56.28%

I'm fairly new at networking stuff and I have a problem setting up an FTP server at home.

So this is the situation.

I want to use my QNAP TS-219P as a FTP server. I have a WRT160 v1 router linked to my modem and the entire network (including the QNAP).

As I understand to establish an FTP server, you need to forward a port on the router to the static IP of your FTP server. By default this is 21. Now here lies the problem.

My ISP blocks all incoming port below 1024, so port 21 is not available for me to use to access the FTP outside the network.
I did get the FTP server running (only inside the network) by opening the default FTP port on the WRT160N (on the admin page: applications&games > Forward a single port > enabling the FIXED application "FTP" and putting in the QNAP IP address).

So I tried to set-up my FTP server by opening a port higher than 1024 on my router (e.g. external port and internal port = 8000) and changing the access port to 8000 on my QNAP. When I do this, I can't connect to the FTP inside as well as outside the network.

Because I didn't know what was causing the problem I reset the FTP port on my QNAP to default 21 and changed the internal port on my router to 21 (keeping external port to 8000). Still nothing. If the QNAP was causing the problem, it would be fixed doing this, I think.

As far as I can tell from this Open Port Tool www.dyndns.com/support/tools/openport.html port 8000 on my router is open and should be... Read more

A:Problem with manually assigning FTP port on WRT160N

7 more replies
Answer Match 55.02%

I went ahead and searched through the forums, but I didn't find anything that may work in my case, so I thought I would ask here.

For the past few months, the battery on the laptop will not charge although it is plugged in correctly - I checked the pin inside the adapter connector, and it is straight as an arrow. Fiddling with it does not fix it at all. I am using the original adapter that came with the laptop. A few weeks ago, I installed the new BIOS, but the problem is still there.

The laptop gets a message during startup that reads
"AC Power Adapter wattage and type cannot be determined. The battery may not charge. The system will adjust the performance to match the power available. Please connect Dell 65W AC Adapter or greater for best system performance. To resolve this issue, try to reset the power adapter."

When the laptop, the battery icon says "plugged in, not charging."

One time, I managed to fix it by unplugging the battery for a while and reinserting it, but after a week or so, it kept happening again.

The laptop is a Dell Inspiron 1521, and it's only 1.5 years old. I understand this may be a battery problem, but those can be rather expensive, and it seems a little soon for the battery to be dying. I'd rather try to rule out anything else before I have to buy another one. I don't have a spare to test it, but is there any other way I can try to figure out what's going on? Or does anyone else have any thoughts on ... Read more

A:Dell Inspiron Power Adapter problem

It's almost certainly the battery. Depending how it was cared for, how much it charged/overcharged, and what type it is, it may not be at all unusual for it to quit after a year and a half. Do you know what type it is (Lithium, NiMH, NiCad, etc.)?

It can't be the adapter if it is powering the machine.

What percentage charge does it say the battery has?
 

2 more replies
Answer Match 54.18%

Hi -- not sure if this is the right place for this, so apologies if it's not.

I've had my Dell Inspiron 600m for about a year and half, and in the past couple months, the power adapter seems to "shut off". The green indicator light goes out, and my laptop begins to run on battery power. If I unplug the power adapter and plug it back in, it starts working fine again.

The frequency of this seems to vary, and I can't identify any behaviors I'm doing that are associated with this happening. Sometimes, if I leave my laptop unattended for a couple hours, I'll find that the power adapter has shut off and the battery has drained to the point where the laptop has to go into hibernation mode.

What might be causing this? Is it something wrong with the power adapter itself, or something in the motherboard or laptop itself?

Any advice would be much appreciated!
 

A:Problem with Dell Inspiron 600m & power adapter

The problem is most likely one of three things. However, I have to ask a two question first!

Do you mean the GREEN light on the AC Adapter or on your Laptop. I am assuming on the AC Adapter for this response.

Do you keep your laptop plugged into the same outlet all of the time? The reason I am asking this is that it could be a bad outlet or the outlet could be damaged and the power supply is simply losing connection at the outlet.

1. Possible outlet problem as in it has a worn plug in and the ac adapter loses contact. This can also happen on a power strip too!

2. Could very well be a failing ac adapter.

3. Could also be caused by the battery.

If #1 is a possibility, try a different wall socket.

If it does it in all sockets, you could remove the battery and plug the AC Adapter into the laptop. It should run without the battery too! This would rule out the battery as being a problem! If the AC Adapter fails without the battery, then it is the AC Adapter. If it works with the battery out, then it is most likely the battery!

Hope this helps!
 

1 more replies
Answer Match 54.18%

I seem to have bad luck with power cords. I went through 3 on my Toshiba laptop. Now my "new" (2 year old) DELL is starting to flicker off and on between AC and battery. Is there a way to find out where the problem is...in the cord or the inner workins of the socket? This problem is getting expenive as replacements cost run between $70 to $100+...
Thanks for any advice you can offer.
 

A:Solved: Dell power cord adapter problem

9 more replies
Answer Match 54.18%

I plugged in my dead(battery needing charged) laptop only to have the power adapter start making a high pitched whinny sound. The green light will not light up on the box. Any ideas what could be wrong with it? If there is no way to get it back in working order, does anyone know of a cheap and good place to find a new one? And how do I tell if its actually the one I need? My power adapter says its part of the PA 10 Family, It also states 100-240v-1.5a, Output is DC 19.5v 4.62a. Any help would be greatly appreciated as my son watches movies on my laptop and is very upset that I can't get it working. Thank you so much in advance.
 

More replies
Answer Match 53.34%

Hello!I've problem with my dell inspiration n5110 laptop. At the beginning there was sometimes a screen like below, but now I've it on every turn on. I haven't changed anything in BIOS, so it could be the power adapter problem? Which one should I buy to test it?I have all original parts in my laptop.I'm little surprised about this 130W Adapter. Could I buy dell adapter with params 19,5V 4,62A 90W or should I look at the 130W?

A:AC power adapter problem in dell inspiron n5110 - screen inside

Hi,
I have a problem with my Dell inspiron n5110 laptop. After turning it on I have a message like below:
All parts in my laptop are original (from Dell). I think that could be a problem with power adapter or with battery. My battery:
What should I do with it? Change AC power adapter? Update BIOS/change BIOS settings?Thanks.

5 more replies
Answer Match 50.4%

The tips I got with this Kensington 33197 power adapter have numbers stenciled on them like N3, N5, N19, etc. The tips sold on their web site make no mention of the "N" numbers and have numbers like K20059, K20050, etc. and there is no cross reference.

You can also see a complete reference for "N" numbers to all the laptops they support at the above link. Again, no mention of the numbers Kensington uses on their site.

I need a cross reference for these kinds of numbers.

Kensington referred me to their telephone tech support; but, there is a language or cultural barrier that prevents their understanding what I need.

Does anyone know of such a reference?
 

A:Need power tips reference for Kensington laptop power adapter

6 more replies
Answer Match 50.4%

My laptop will no longer turn on.  When the AC adapter is plugged in, the LED light is white indicating power is arriving at the laptop. However, nothing happens when I push the power button. Troubleshooting steps I have completed already include: Hard reset (several times including after each step below)Tried starting without the batteryRemoved all removable components and reseated themRemoved all removable components as well as bottom cover. Cleaned with compressed air. Put everything back.Nothing appears wrong and nothing happened between the last time it turned on and this time that I am aware of. The laptop is out of warranty, and I am pretty handy with computers. Is there anything that can be suggested short of a hardware replacement that would help get this resolved? TIA

More replies
Answer Match 48.72%

This is a common problem (I see lots of posts)
The problem source is the [Dell] AC adapter.  PA-21 Family, 65W, P/N: NX061.  It is made in China.
I have an XPS M1330.  Using Dell after warranty service, replaced the Mother Board twice, replaced the battery twice, replaced the AC adapter twice - not fixing it.
Turns out the power warning message is very informative.  It states "Please connect a Dell 65W AC adapter or greater for best system performance".  So, I plugged in my Dell 95W adapter - WOW Problem Solved.
A lab test of my new Dell 65W AC adapter shows it to be 64.6 watts.  If this unit gets hot (like after several hours of use), it may not put out the full 65 watts - the system may not recognize the adapter, it may power the system ok, but won't charge the battery.
These units burn out after only a few months of use. Their cables are too fragile. If Dell's or their supplier's Quality Control can't produce a reliable 65W product - I found seveal "Made In USA" universal adapters.
 

A:AC Adapter - Alert - "AC power adapter wattage and type cannot be determined"

Well my solution was simple.
I just removed the battery pack and powered up my notebook. Then I turned off the notebook replaced the battery pack and VOILA. The error message was gone.

10 more replies
Answer Match 46.62%
Q: Wrt160n

I am running windows 7 Ult, and have rr for my isp and about everytime I want to dl something I have to log into my routers setup page and release and renew the ip or sometimes reset it manually. The router is not that old, it is a Linksys WRT160N Firmware Version: v3.0.00. Any help on this?
 

A:Wrt160n

Perhaps the shortest fix is the long remove and replace as you reinstall your system... most certainly it is in the setup, not in Windows 7 Ultimate
 

2 more replies
Answer Match 45.78%

Ok, I am having some wireless router issues, which have been, by trial and error, tracked back to the wireless router I have. WRT160N V3. I contacted linksys support, and because the router is 3 days out of warranty, they wanted $30 US to help me configure the router. Or, he referred me to the linksys help page. I can't seem to find how to update / re-configure the router from their pages. Anyone able to give me some guidance?
 

A:linksys wrt160n v3

7 more replies
Answer Match 45.78%

I'm not positive on which forum this belongs in so sorry if networking is not correct.

My Linksys Wireless WRT54G router recently broke for no reason. It has been good to me over the past year, but I've discovered a few dead spots, and also a bit of a slow connection. I'm not too picky when it comes to my ipod touch/laptops but when it hits the XBOX LIVE i get so extremely frustrated.

Supposedly nobody uses G routers anymore, in other words they are ancient tech now. I need a N router that is better than this one but under $50. I've found these two on ebay.

Netgear WNR2000:
Netgear WNR2000 RangeMax Wireless-N 802.11n WIFI Router - eBay (item 380170045183 end time Nov-19-09 12:12:42 PST)

Linksys WRT160N:
Linksys - WRT160N Wireless-N Broadband Router - eBay (item 400080229434 end time Nov-19-09 03:29:54 PST)

I've heard some horrible things about Netgear's routers, i thought maybe you guys could tell me which of these routers is better. They are both perfectly in my price range so I'm hoping one of them will suit me. (Btw I don't care much about range, only need enough for a small 1 floor house)

Thanks.

A:WRT160N, or WNR2000. Please help.

???

3 more replies
Answer Match 45.78%

Thinking of buying a LinkSYS/CISCO WRT160N router. Anyone have an opinion on these? I want to use it on the far side of my house for a wireless laptop and a netbook. The WRT160N will be connected to my DSL modem via CAT 5 cable at the other end of the house.
 

A:Opinions on WRT160N

It depends on how far and what obstructions there are. It's a decent router, but any wireless router has range limitations, and the more obstructions, walls, electrical interference, etc. in the environment, the shorter the range will be.
 

3 more replies
Answer Match 45.78%

For the last two weeks, every time I start my Dell INSPIRON E1705 while using the power supply I am greeted with the following message. "The AC power adapter type cannot be determined. Your system will operate slower and the battery will not charge. Please connect a Dell 90W AC adapter or higher for best system operation". I press the F1 Key and everything works fine. I've read about this on other websites and most say it's a design flaw in the power supply after the cord has been properly wound around the supply as designed. Apparently a few of the cords internal wire strands become broken and cause this message. My computer is from June 2006 and shouldn't be having this issue so early...or ever. This seems like a flaw that should have created some type of manufacturers recall since so many people are having this issue. I'm of course out of warranty, will Dell replace this free of charge?
 
`

A:Power Supply - "The AC power adapter type cannot be determined....."

You are correct, the failure is due toloss of the power supply ID signal. Sometimes this happens because of strain on the plug, which breaks the signal wire. Some even are so severe that the insulation breaks away from the plug; this is due to rough handling. The other cause is one or more of the power socket solder connections to the system board become broken. This also is related to severe handling. I have seen one case where all three power connections and three of four mechanical connections were disconnected. If the power supply is bad, a replacement will cure the problem. If not, then the socket is bad, and this will require a system board replacement. If you are experienced, you can try to resolder the connections. I am experienced and was not able to get my daughter's E6000 to work by resoldered. More recent Dells are using a replacable power connection board which is a much cheaper repair.

64 more replies
Answer Match 45.36%

My desktop specs: http://www.techcomet.com/p/my-gadgets.html

I have a Linksys wireless-n router connected directly to my desktop's network card.

I have set it up so that when I send a magic packet over my network my desktop switches on from s3 sleep. Essentially, Wake on LAN is working fine over my wireless network.

What Wake on LAN does is send a "magic packet" to the "broadcast address" (192.168.1.255) of the linksys router. I also have to enter in my devices MAC address which means that the magic packet is only received by my desktop (and no other computer on the network).

Over the LAN WOL works fine. However, it is over the internet I am having a problem.

I have used DynDNS to set up a custom domain which connects to my external IP. The wifi router also has "DDNS" section where I can input the DynDNS settings so the router automatically updates DynDNS whenever my external IP changes. So, my domain stays the same (e.g. domain.dyndns.org) while my IP changes.

To ensure that my custom domain works when connecting to my PC, I have used VNC. I can connect over the internet to my computer and control it without any problems.

The problem I am having is that I am unable to use WOL over the internet.

I have searched the web and found a number of solutions that sometimes works and sometimes doesn’t.

Firstly, it has been suggested that I port forward the port through which the magic packet is sent through to the routers broadcast address.... Read more

A:WRT160N - Wake on LAN over Internet

Try this site, they also have an Internet based WOL test to see if you can pass the magic packet and wake a machine on your network. http://www.depicus.com/wake-on-lan/
 

1 more replies
Answer Match 45.36%

I've been trying to read reviews of various routers but am only getting confused about the conflicting information and positive and negative reviews.

We currently have a WRT-54G (for the last 4 years). The last two months we have started to play a game for our Nintendo Wii online. It seems on occasion, we experience disconnection problems. We'll have zero problems for a week or two but then for two days straight we experience a problem with staying connected (we can connect and race a race or two, and them - boom, disconnected). We've spoken to our road runner provider and it's not an issue with them.

So. . . we were wondering if perhaps the WRT-54G is just failing and were trying to figure out what to get instead without spending a lot of money. We saw the Linksys WRT160N and were considering it because of it's supposedly extended range. But, while we did see reviews saying wonderful things about it, we also saw reviews saying that the range was no better than the WRT-54G.

I guess we are wondering if the WRT-160N may be a good solution to our occasional disconnection problem?

Our house is medium to large but we use our laptop and the Wii within 50 feet of the current WRT-54G. We've noticed that when we are having disconnection problems with the Wii, that if we are surfing the net around the same time we occasionally have a problem loading a page on the first click. Fortunately, if we click the page again it loads. It'... Read more

A:Linksys WRT160N (replacing WRT-54G)

have u tested to see if the Wii i losing connection while the Lap top is staying connected?
 

3 more replies
Answer Match 45.36%

I can not get on the internet using the Linksys WRT 160N router I reset the modem and router Got help from Motorola and Linksys but still can't get on internet thought router. any ideas?
 

A:Solved: Linksys wrt160n

9 more replies
Answer Match 45.36%

I've been struggling with my router for almost 2 years now. It's a WRT160N Linksys wireless router. My computer is using the Ethernet connection, not the wireless.

It's always these two issues:

Without Static IP:
The router automatically forwards SOME ports (most Blizzard games for example) but does not allow most other programs (connecting to my computer as a server with my laptop on another network as the client)

WITH Static IP:
no ports are forwarded, nothing works but basic internet access.

My ISP is Comcast, and they say everything is fine. Linksys is trying to charge me 30 bucks per call for tech support. I need help!

EDIT: I just tried Static DHCP on my router (meaning that my router always assigns the same IP, like static IP does) and it still doesn't work. Port checks still say closed.
 

A:WRT160N port forwarding

6 more replies
Answer Match 44.94%

problem w/ Microsoft 6to4 adapter (network adapter)

I am frequently being disconnected from the internet.

Microsoft 6to4 adapter (network adapter) has a exclamation mark (!) in a yellow triangle in device manager.

This device is not working properly because Windows cannot load the drivers required for this device. (Code 31)

Click 'Check for solutions' to send data about this device to Microsoft and to see if there is a solution available.

When i check for solutions, it says cannot load driver software.
 

A:problem w/ Microsoft 6to4 adapter (network adapter)

See this

http://support.microsoft.com/kb/932520

If there are no problems connected with this code31, ignore it.
 

1 more replies
Answer Match 44.94%

I have a Linksys wireless router WRT160N, and its worked fine for the past year, till last night, when I pushed the reset button trying to solve another issue and now my router isnt working. I ran Linksys setup disc and it said I was all up and running, but still cant get online with my laptop through the router.

I am at a point where I have my default gateway address 192.168.1.1 and my IP address, but not sure what to do with that to get this issue corrected.
 

A:Linksys WRT160N router issue

16 more replies
Answer Match 44.94%

Hi

Much like a chap a while back I have a WRT160N V3 Router from Linksys/Cisco. I have successfully upgraded it to dd-wrt.v24-21061_NEWD-2_K2.6_mini_wrt160nv3 (DD-WRT v24-sp2 (01/02/10) mini), and I am now trying to upgrade it to dd-wrt.v24-21061_NEWD-2_K2.6_mini_hotspot.bin to get Hotspot System support. Every time I have received the message "Upgrade Failed", and I can't figure out what's wrong, because this release supports this router revision.

I've tried all the 30/30/30 reboots and changing browsers etc but no luck.

Any ideas? I want Hotspot System as it gives me a simple, free portal based hotspot, am also open to other solutions?

Thanks!
 

More replies
Answer Match 44.94%

I have Windstream as my ISP. They provided me with a speedstream 4200 modem/router. However, I have a linksys WRT160N behind it as my router. I have looked all through the 4200 for a way to disable the router part, but cannot find it. I have been having a lot of internet connectivity problems with my modem losing sync with the Windstream servers as well and I do not know if it has something to do with my current setup. Is there anything I can do to get this setup correctly? Thanks.
 

A:Linksys WRT160N Behind Speedstream 4200

11 more replies
Answer Match 44.52%

Can I use 45 Watt adapter for dell inspiron 15 5559?? I got the adapter along with the laptop when I bought it. But a warning is displayed on screen prompting me to use 65 Watt adapter... If so why 65 Watt adapter wasn't given with the laptop instead of 45 Watt?

A:Power adapter

Hi SUSMI,
The system is designed to support both 45W and 65W adapters - see the specifications here - http://dell.to/2fhPLIf
When you plug in the adapter to the system, does the adapter stay firm or does it fall off easily? Is the adapter frayed? Could you test with another power adapter if possible?
Restart the system and press f2 key to enter BIOS - check the adapter status in BIOS with and without the adapter plugged in. Also, wiggle the adapter cable at the end and see if the status changes in BIOS at any point.
Restart the system and press f12 key on startup - choose diagnostics. Let it run the diags and if you encounter any errors - make a note of the complete error and report the same to us.These are onboard diagnostics and they might possible pick some error if the hardware is not functional.
Also, please click my DELL-username and write me a private conversation with the service tag and your contact details(Name and Email) for case records.
Let us know if you have any other queries.

1 more replies
Answer Match 44.52%

I have a Toshiba Satellite C655D that needs a replacement ac power adapter, when I look it up it says I need:

Laptop AC Adapter: 19 Volts, 75 Watts, 3.95 Amps, 5.5mm x 2.5mm Connector

or

Laptop AC Adapter: 19 Volts, 65 Watts, 3.42 Amps, 5.5mm x 2.5mm Connector

Someone gave me a new, in the box AC Adapter with USB port, made by Insignia.
The documentation says "converts 120v AC to 3-12v with 1300mA max output."

I realize this is a question not exactly hardware related, but I'm hoping someone knows the answer....I'm afraid to plug it in and fry my laptop

 

A:ac power adapter...

7 more replies
Answer Match 44.52%

I recently bought a replacement power adapter for my dell e1505. The computer works but it won't charge the battery and tells me that since the computer does not recognize the charger, I need to reseat the power adapter... What does that mean?

A:Power Adapter

Hello aaronbaron,

Reseat the power adapter just means make sure the power adapter is plugged in good on the laptop and the wall outlet. I would try powering off the laptop, unplug the power cord, take the new battery out. Reinstall the new battery only and try to power on the computer. If that does not work plug in the power cord and power up with the new battery installed.

Raj

1 more replies
Answer Match 44.52%

I have noreen indicator dont lighttebook Dell Inspiron 5558. Today something happend with my AC Adapter and my notebook cant charge. Green indicator doesnt light Where i can buy the  same AC Adapter?

More replies
Answer Match 44.52%

I bought a Dynex USB 2.0 4-Port Hub last week and have decided to add an external power supply to power the hub. The short and terse User Manual notes on the final page that a 5Volt / 2.5 Amp Power Adapter may be connected. I called their customer support number and talked to a lady, but her best advice was return to the store and ask there. My experience with this store over the years has been fat chance for this kind of request. Has anyone got a suggestion as to where I can purchase such a USB Power Adapter?
 

A:USB Hub Power Adapter

Radio Shack would be a good place to start although you might have to get one of their adjustable models. A Google search should also turn up something. Actually I just replaced my D-Link powered USB1 hub with a USB2 model. The old one is just sitting around and it has a 5V 2.4A adapter. If you want it so you can use the adapter just PM me and I'll send it to you.
 

3 more replies
Answer Match 44.52%

Hi.

I got a USB Hub here and I need to get a power adapter for it. On the hub, it says 5V. I currently have a 6V power adapter. Would this be safe to use?
 

A:Power Adapter for USB Hub

16 more replies
Answer Match 44.52%

I have notebook Dell Inspiron 5558. Today something happend with my AC Adapter and my notebook cant charge. Where i can buy the  same AC Adapter?

More replies
Answer Match 44.52%

This is probley not the place to ask but, I have a cardscan and I lost the 4.5V power adapter. The end is very small and I haven't had any luck finding one. I even went to their web site and nothing. I also e-mailed them with no response. Can anyone help?
 

A:Power adapter?

From their website:

<BLOCKQUOTE><font size="1" face="Verdana, Arial">quote:</font><HR>Contact our Customer Service department for the following types of inquires:
...
Lost CardScan adapters.
...

Call 617-492-4200 ext. 3 between the hours of 8:00am - 5:00pm EST Monday-Friday.
<HR></BLOCKQUOTE>

Have you called them yet?
------------------
Get free stuff and help out a poor computer tech:
LarryCore begs for money
 

2 more replies
Answer Match 44.52%

It Just Turned Off All Of a Sudden - Linksys WRT160N Dead?

Well we just got a wireless router today from Best Buy since we bought a laptop.

Anyways, the router just stopped suddenly after my sis connected a USB device to the main computer.

Then when I unplugged and replugged it in, the router just started to blink and still couldn't connect!!!

We're probably going to exchange it tomorrow or tonight but can anyone diagnose the problem for me.

Router is the Linksys WRT160N just to remind you guys.

Thank You,
Tim
 

A:Linksys WRT160N Dead? It Just Turned Off All Of a Sudden

Reset your router to factory defaults by pressing the reset button for 30 seconds

If it's still a no go, replace under warranty
 

6 more replies
Answer Match 44.52%

My primary router is the Comtrend WR-5882 wired and WIFI router. My secondary router is the Cisco Linksys WRT160N. I want to make the secondary one into a repeater so it receives the WIFI signal from primary and sends it out to other devices, which will extend my WIFI signal over a larger area.
Yes, I have researched it but I am coming up with confusion. Please help.
 

A:Comtrend WR-5882 WIFI and Linksys WRT160N

i dont think that router allows extender/repeater functions
http://downloads.linksys.com/downloads/userguide/1224640959708/WRT160N_V10_UG_A-WEB.pdf
 

1 more replies
Answer Match 44.52%

hi , i have a problem during setting up my wrt160 linksys routers
my internet connection dropped too many times sometimes not working at all
this is what i do at first
i flashed my router with ddwrt firmware and set it default with 192.168.1.1
modem input goes to the WAN input on router....
1st router i put on my living room.
now 2nd router i flashed with ddwrt also and set it 192.168.1.1
and then i hardwired from 1st router to 2nd router thru the wall and plug it on the LAN 1
any idea what i do wrong here?
thanks
 

A:setting up 2 linksys wrt160N on separate room.

10 more replies
Answer Match 44.52%

Here's my problem that I just cannot figure out. My Linksys WRT160N has four pc's wired directly to it. Three of the four ports work fast enough for my usage. Using Speedtest.net I am able to achieve download speeds on each of these three ports of between 12-18Mbps with pings of 41.
However, on the fourth port I can only achieve around 2.5Mbps with a ping of 55. Here's what is wierd: I can swap out the fourth slower pc with one of the other faster ones and the slow readings remain the same. I have even connected the slower pc to one of the faster ports and it works very fast.
I also replaced the cat5e cable but that didn't help either. So I know it isn't the computer or the ethernet cable. I can only conclude that it is the router port.
I hope this isn't confusing.
I am wondering if there is a setting in my Linksys WRT160N that affects the single port that is giving me the problem? If so, what can or should I do?
Thanking you in advance.
 

A:One port on Linksys WRT160N is slower than rest

I am wondering if there is a setting in my Linksys WRT160N that affects the single portClick to expand...

Don't know about any such setting on that router (too lazy to read the manual ), but I've never heard of such a port restriction and seriously doubt that it would be a default setting.

what can or should I do?Click to expand...

1. While I doubt that it will help in this case it shouldn't hurt to do the "standard" router fix--make sure you have the latest firmware; then reset it to factory default settings and reconfigure.

2. If under warranty get a replacement.

3. Get a small ethernet switch to connect to one of the 3 good ports and put a piece of tape over the bad port.
 

1 more replies
Answer Match 44.52%

For whatever reason, we can no longer connect to the internet wirelessly in our house. Background - The phone lines at our house accidently got pulled loose during construction. My hubby reconnected and since then no wireless connection. We got a Gateway desktop running XP SP3 wired to the modem with great connection. None of the wireless devices in the house can connect to the linksys WRT160N router. When I search for available networks, the laptops do not find any available networks.

I did a hard reset of the linksys router back to factory settings but we still can't get online wirelessly.

I'm pretty new to this so detailed explanations may be necessary. BTW - I called Linksys and the router is out of warranty. They wanted $39.99 to help and when I told him no, I'd pass, he told me it was very technical and he doubted that any free tech board could really help me. Well, that pretty much did me in and I'm now determined to find online help for this problem!

So if you have any suggestions/ideas/questions, I'd truly appreciate your help.
 

A:Linksys WRT160N wireless router issue

Connect to the router with a wired connection to one of the LAN ports.
Access router setup page by typing router ip (default is 192.168.1.1) into the IE address bar.
Enter password at prompt (default password is "admin" with no username)
Goto wireless/basic wireless settings tab click to view set "configuration view" to manual"
Save settings
Goto wireless security sub-tab click to view
Select desired security mode (WEP/WPA) and set password.
Save Settings

 

3 more replies
Answer Match 44.52%

Well, I recently switched to TekSavvy internet, and it's fine, but I can't stand that my internet keeps randomly disconnecting! (All of my devices are connected wirelessly). How do I fix this? Here are some of the specs
Using TekSavvy Cable Internet 28dl/1up
Linksys WRT160N router
TekSavvy modem bought

I'm not sure too, but I have DCHP and for MTU I have auto on. I think my computer has also told me once that I had same IPS on some computers as well.

Please and thanks if anyone could help
 

A:Solved: WRT160N router keeps disconnecting from the Internet?

16 more replies
Answer Match 44.1%

I have a 20 pin motherboard but the power supply I have available has a 24 pin connector. I've read that you can simply plug them together by offsetting the 24 pin one but so far I don't see that working at all (and 'never the twain shall meet', so to speak). I've found adapters but they all say something akin to

'allows you to connect your existing 20 pin power supply to your new 24-pin compatible motherboard'

You can use it the other way around, correct?

thanks

mystmaiden
 

A:20 to 24 pin power supply adapter

Some mainboard connectors are 20+4 pins where the 4 pins unsnap from the 20 pins for use with boards with a 20 pin connector. If your power supply doesn't have that feature you would use an adapter such as this.

http://www.atxpowersupplies.com/24-pin-to-20-pin-atx-converter.htm
 

2 more replies
Answer Match 44.1%

I have a compaq nx6325 lap top, which will not turn on at all. The power adapter
shows 18V between the inner and outer ring and appears ok, led on etc.But what's the tiny center connector for in the plug? Should there be a voltage on it to earth, or to the ring connectors?Finally,should I be able to power-up the lap-top with the power adapter plugged in, and the battery out?
 

A:Power adapter center pin

Sounds like the Centre pin has broken away and lodged itself in the plug. I cannot tell you which is positive and which is negative with regards to the rings on the plug. Because different Manufacturers use different combinations and with that different Voltages too. Generally speaking the outside piece is the male end and the receiving plug is the female -go figure-
Hope this link works http://www.niteflux.com/BuyCables.aspx you can see what I am mentioning, obviously this is not your cable but for the example of male to female ends the description matches the pictures ( not the 'Y' cord on the link )
 

2 more replies
Answer Match 44.1%

I had the power cord replaced last year. But now I find the power box cord is not working. My battery died completely and even with the power cord plugged in, my laptop will not work. The box, even after replacing the power cord, still got extremely hot. Now I can't use my laptop at all! What do I do andhow much is it going to cost? Why is this not on a recall?

A:Power adapter for HP Pavillion g7

Hey, contact hp hp and check if there is any recall, if there is the repair will b done, else they hey will give you the exact cost for the repair. #hpexpertday




Regards;SmileyI am an HP employeePlease click the White Kudos star to say thanks for helping.Please mark Accept As Solution if my help has solved your problem.

3 more replies
Answer Match 44.1%

I have a laptop, Toshiba Satellite A75-S209.

I want to be able to run it in my truck using Microsoft Streets with GPS. Which is better, DC Adapter or DC power Inverter? How much wattage do I need? Will it drain my truck battery?

Thanks for your help, Dee
 

A:?? DC Adapter or DC power Inverter ???

I can't imagine a laptop would need any more than 150 watts...
 

2 more replies
Answer Match 44.1%

does my acer v5-571P-33224g50Mass with Intel(R) HD Graphics 4000 able to take the 90w power adapter Part Number: TP.PWCAB.21-A05-AS?

A:90W power adapter with V5-571P?

Hello, All Aspire V5-571P models are shipped with an adapter of 65W. Why do you want to buy one of 90W?

2 more replies
Answer Match 44.1%

Though I had posted this previously, but cannot find it anywhere!

Got an Altec Lansing Multimedia Computer Speaker System ACS41. Apparently they were used on a Gateway 2000 PC.
However, the power adapter was lost.
The speakers do not have any electrical specs on them regarding voltage, amps, and polarity.

Anyone have a similar set of speakers, or,
know of any way this type of info can be found out, in order to get the right power adapter for them. Do not care to fry them with an overkill. The speakers probably came with PCs running Windows 98SE, or Windows Millennium.

Prefer not to go to Radio Shack, they normally are rather expensive, and the people who own this do not want to go that route.

Thanks for the help.
 

A:Power Adapter for Speaker Set

We had a system crash here and some posts were lost. There was an answer, but I forget what it was. It may be as cheap to buy a new pair of speakers as to buy a power adapter.
 

2 more replies
Answer Match 44.1%

Can anybody answer the following questions about a laptop power adapter?

Is there a maximum length for the dc cord? In other words why do they locate the adapter 1/2 way down the cord instead of closer to the outlet.

Is the small cylinder around the cord about 3" before it enters the laptop some sort of choke/filter?

Thanks.
 

A:Power adapter modifications

kraftzion said:





Is there a maximum length for the dc cord? In other words why do they locate the adapter 1/2 way down the cord instead of closer to the outlet.Click to expand...

There is no particular reason for this, either side of the power supply could be lengthened or shortened.





kraftzion said:





Is the small cylinder around the cord about 3" before it enters the laptop some sort of choke/filter?Click to expand...

I'm not positive but thats what I have always thought it was.
 

4 more replies
Answer Match 44.1%

Hello!

I received the following message when I am booting up my Dell ATG Laptop. Does this mean I need a new power cord? If so, is there anywhere recommended to purchase or do I just go to the dell website?

The AC Power Adapter Wattage and Type cannot be determined. The battery may not charge. The system will adjust the performance to match the power available. Please connect a Dell 65W AC adapter or greater for best system performance. To resolve this issue, try to reset the power adapter. Strike the F3 key (before F1 or F2 key) if you do not want to see the power warning again.

Strike the F1 to to continue. F2 to run the setup utility, Pree F5 to run onboard diagnostics.
Thank you so much for the assistance!

Baxter
 

A:Solved: AC Power Adapter

It may be the AC Adapter, or the internal battery has died.
 

3 more replies
Answer Match 44.1%

The Yoga 3 Pro power adapter looks like a normal USB brick, and the cord looks like USB, except with a kink in the connector at the Yoga 3 Pro end. Can I charge my phone or tablet with it?

A:What's with the Yoga 3 Pro power adapter - it's a ...

Yes the Yoga 3 Pro power adapter is a USB charger too!
 

How does it work?

The special "fool proof" charging cord has two extra pins on the AC adapter end and two extra pins on the Yoga 3 Pro end. The extra pins only make a connection when the fool proof cord is plugged in to the Lenovo charger and the Yoga 3 Pro. When a regular USB cord is plugged into either the charger or the Yoga 3 Pro, it makes a regular USB connection.
 

Can I charge the Yoga 3 Pro with any USB charger?

No. The Yoga 3 Pro requires 2A at 20V, which is what the provided 40W Lenovo AC adapter supplies.
 

Can I charge a USB device with the Yoga 3 Pro AC adapter?

Absolutely. In addition to 2A at 20, the Yoga 3 Pro AC adapter supplies 2A at 5.2V (10.4W), enough to charge a phone or tablet. Works for iPad.
 

Where can I buy spare AC adapters and cords?

AC adapters with cords are sold in the accessories section of the Lenovo store.
 

Where do I find the part numbers for the AC adapter and cord?

Look for AC Adapters In the PDF Yoga 3 Pro Hardware Maintenance Manual.
 

What are the USB specs of the Yoga 3 charging port?

It's a USB 2.0 port. It provides enough power to charge an iPhone, but not enough to charge an iPad. If you want to charge an iPad, try the USB 3.0 port on the right of the Yoga 3 Pro.
 

The Yoga 3 Pro power cable connectors compared with a regular USB connector:

9 more replies
Answer Match 44.1%

 I recently bought a new HP laptop & was supplied with a cable suited for Europe not Australia. The message below came up after I plugged the cable in using a univeral power adapter. I contacted HP about getting a replacement cable which arrived today & once again the same message popped up.  Is this something to be ignored? Any help will be greatly appreciated.   

More replies
Answer Match 44.1%
A:Where can I purchase an A/C power adapter for a VT...

Hello, Could you give me the first ten characters of the computer serial number (S/N)? Only the first ten.(I guess you own a Veriton 1000).

1 more replies
Answer Match 44.1%

where can i get a car power adapter or charger for  Yoga 13?

A:where can i get a car power adapter or charger for...

Hello,You can to use a converter 12V/220V or 110 V.It's not more expensive than an other charger, and you can to charge all devices.

3 more replies
Answer Match 44.1%

Hi Guys,

I was hoping someone could help me out finding a power adapter for an old set of Harman Kardon speakers I have. On the back of the speakers it says ac 15v 1.1A so I assume I need an adapter that matches those settings.

Can someone plz help me out finding one that will work and is as cheap as possible.

Thx a bunch.

A:Power adapter needed

This?
Robot Check

1 more replies
Answer Match 44.1%

I had a drink spilt on the power adapter where the power plug connects into the laptop.  I need to get a replacement since, I use the laptop fairly regular and can't seem to find any that are HP

A:HP Pavilion g6 Power Adapter

Does it have to be HP specifically?Plenty around on the web, these are just examples:60 Watt HP G6 G7 power adapter $8.98 on Amazonhttps://www.amazon.com/HP-Pavilion-G6-Adapter-Charger/dp/B0080E2G6EOr newer model 90 Watt faster charger $11.99https://www.amazon.com/Warranty-Faster-Charger-Aluminium-Cooling/dp/B00MGAA80E/ref=dp_ob_title_ce

2 more replies
Answer Match 44.1%

I have a 90w power adapter from an older notebook that will work with my HP DV5-1015nr. I transport my notebook between home and office. I'd like to utilize the older power brick, so that I won't need to transport a power brick back and forth. The tips on both adapters, of course, are of a different diameter.      My multi-tester identifies that the tip is hot for both adapters. The problem I have is that the older power brick has two wires: core wire (+) and shield (-), and the newer power adapter has three wires: shield that is connected to the core of tip (+), black that is connected to outer part of cylindrical shaft that must be the ground, and white connected to inner part of cylindrical shaft (also negative?). So do the black and white wires on the newer adapter need to be soldered to the shield on the older one?   

A:Wiring for Power adapter?

Just a guess, since it is 90watt, they may have run the extra wire to carry the load, shield is always much larger than center tip wire. Did you measure voltage and ploarity of all three connections with the brick plugged in? Tip is always + and ouside is always - on a HP, not sure what the third is, see if there is any voltage on it, It could also be some sort of sensor wire for the charging system on the mobo. Better to buy another adapter than smoke the motherboard on the lappy taking a chance. If you want to chance it just connect the two wires that are on the center and outside. Leave the 3rd odd one unconnected. probably can be found used for cheap.

8 more replies
Answer Match 44.1%

Hi all,

i hope im posting in the right section....(apologies if not)

The power adapter/charger for my toshiba laptop failed recently.

Im looking for a replacement and have see several different options.

The original toshiba part (part no: PA3290E-3AC3) is available for about 50 pounds
however ive seem lots online which are the same spec, and described as replacments for the above part. the thing is these cost less than half the price of the original
Although these are not the genuine part it says they will work.

i was a bit worried that it may damage my laptop if i dont use the exact part.

could anyone advise me on this please and the best thig to do.

Thanks
A
 

A:power adapter does not work

I have a Toshiba that I am using an adapter made by Lite-On. I have been using it for about 2 years and no ill effects. It was about 1/3 the cost of the Toshiba adapter.
 

1 more replies
Answer Match 44.1%

Seeking adapter for lenovo ideapad U330 touch. I want to buy a power bank but I need specific adapter for my computer. The power supply input is almost like a rectangular USB port (like in the photo). Thanks for your answers. ?

More replies
Answer Match 44.1%

when i start my computer with the power adapter in i get a message saying can not determoin the power output of power adapter try reseting adapter. How do you reset a power adapter iv googled it and nothing. please help thanks sorry for bad spelling.
 

A:need to reset power adapter

i don't think you can reset a power adapter - i don't know of one - it will have the correct voltage on the plug or not
whats the make and model of the PC
are you able to use and have a mulitmeter?
 

3 more replies
Answer Match 44.1%

I have an hp pavillion dv 6000 that I lost the power adapter to. My friend has an adapter for an hp pavillion dv9000 that he does not need anymore and he wants to sell it to me. I want to know if it will work with my computer. The adapter puts out 19volts 4.74 amps 90 wants max. The replacement adapters for my model (dv6000) list the power output as 18.5 volts 3.5 amps 65 watts.

Will an adapter that was higher voltage amps and wattage work for my laptop that requires less??? This is assuming that the connector is the same which I'm not sure of.
 

A:Power Adapter question

Higher Amperage and Wattage yes, Voltage? NO
 

1 more replies
Answer Match 44.1%

my power cord and power adapter for a 110-414 PC was ruined in the so La. flooding.  I've tried to order a new set, the power adapter was wrong.  Support doesn't seem able to understand the plug on the ac aapter i recieved is a sigle plug like fits a laptop.  The AC reciever of the rear of my computer appears to be round barrel plug with a small pin in the center a four slots on the outside.  Where can I find this power adapter?

More replies
Answer Match 44.1%

Hi there As I read, 135W adapter is very heavy for traveling and I want something lightweight.What you can suggest for T460p? I dont want lost performance while charging.Also prefferable is a AC plug for EU countries

More replies
Answer Match 44.1%

RESOLVED PLEASE...ANY IDEAS I am in a hotel in Grand Forks, North Dakota. I plugged my laptop into the power adapter and then plugged the power cord into an outlet on the side of a work desk( ). After a frantic day of post Thanksgiving shopping I came back to the hotel, plugged my laptop into the female end of adapter and....BANG ...sparks started to fly from the end of power adapter. Sent attachment. Please tell me what my options are as I need the LT for 3 more days.... Any suggestions. Can this be repaired, I am in Grand Forks.. where should I go
seriously desperate,

Scatteredminds. pps only 10% battery life le f ttttttt.

Found a geat repair shop who spliced and soldered...just temporary until I get back to winnipeg
 

More replies
Answer Match 44.1%

This is a recent problem - a previous adapter broke and now subsequent adapters use 100% CPU and sloooow my laptop.

It's an hp 6720s 13 months old, XP Home, HP 65W power adapter.

Laptop running fine on battery only. Laptop runs fine when battery removed and power adapter is connected. Laptop does not run fine when battery and power adapter connected - 100% CPU.

Also, the charge indicator light no longer works and the power icon does not show that the battery is charging, although it is.

I've updated the BIOS, restored factory power settings and tested the power adapter during startup and have the same prob with the CPU usage.

What could cause the power adapter to use 100% CPU? Please let me know if you need more info, cheers.
 

A:Laptop power adapter uses 100% CPU

Is this an Adapter obtained from HP as a direct replacement for the proper adapter as shipped from HP with the laptop?
 

3 more replies
Answer Match 44.1%

I am planning on making this project myself but first I have one question. Here is the project I will be making:
http://siliconrepublic.blogspot.com.au/2011/02/arduino-based-pc-ambient-lighting.html

It says I need a 12V DC supply for powering the breadboard. When searching up for 12V DC supplies, I only get power supply's that plug into the wrong wall socket (I live in Australia).
Do I need to get something like the article suggests:
http://www.amazon.com/Garmin-AC-Veh...1KZ6/ref=sr_1_2?ie=UTF8&qid=1297231222&sr=8-2

Or can I get something such as this:
http://www.ebay.com.au/itm/DC-12V-1...?pt=AU_Laptop_Accessories&hash=item336678ae52
If the first option is the only possibility, how do I get the plug to go into my wall socket?
Also, how do I get the other end plugged into the breadboard when the product just has a single plug on the end?
 

A:What type of power adapter do I need?

You can use the Ebay adaptor, the easiest way to get 2 wires is to get a socket that fits the plug, like this one :- http://www.ebay.com.au/itm/5-5-x-2-...05?pt=LH_DefaultDomain_15&hash=item4167b5b34d and solder 2 wires to that socket.

The circuit at your link uses a 2 wire plug into the breadboard, you would have to get a similar plug OR you could push bare wires into the breadboard.

OR you could cut the plug off to reveal the 2 wires but they will probably be quite thin and may not connect well if pushed into the breadboard holes.
 

1 more replies
Answer Match 44.1%

I have a Inspiron 15 3541 touch screen and "misplaced" my power cord and adapter. I'm using a Dell adapter from a different computer, but when I turned on my laptop, I get a message requiring a system or admin password even before it boots up. Is this because of the different adapter? How many pins did my adapter have? What problems does a different adapter create?

A:Power adapter pins

The password that is showing up before your computer boots sounds like there is a BIOS password set on the computer.  Unfortunately if you don't remember that password then you are probably stuck.  You can probably go online and search and see if there is a way to reset BIOS on the laptop and get it to default and remove the password that is set on it.  If there is a hard drive password though then the only way to remove that if you forgot it is to install a new hard drive as the password will follow the drive, not the computer.
Your power supply should have only 1 pin.  Dell used the same adapter for their computers for a while, they come in different wattage though and if you use an adapter that is too low then it may not be able to charge the battery while you use it or at all.  If the plug fits and it is a Dell charger you should be okay to at least get the computer up and running.  If it is a low wattage charger and the setting is set in BIOS (usually is by default) you'll get a message from your computer telling you that the charger isn't powerful enough to charge the battery while in use.

1 more replies
Answer Match 44.1%

I have this mode laptop: toshiba satelite p305d-s8900 And am going to have to replace the power adapter pretty soon. It cuts out all the time and the cord is so flimsy it will probably break pretty soon. Any idea where I can get a new one for under $50.00? I'd prefer to have an actual duplicate, not another brand thats just generic and cheap. On Toshiba's website the replacement is $89.00.
 

A:Toshiba - new a/c power adapter - where can I get a new one?

You can try NewEgg.com. Anything under $80 is going to be generic and cheap.
 

2 more replies
Answer Match 44.1%
A:Where can I purchase an A/C power adapter for a VT...

Hello, Could you give me the first ten characters of the computer serial number (S/N)? Only the first ten.(I guess you own a Veriton 1000).

1 more replies
Answer Match 44.1%

I have a Precision 7510 updated with the latest Bios and drivers. Today my TB15 arrived. I haven't tested connecting a monitor to it yet only a network cable and USB 3.0 stick - this worked fine.
I also tried starting the laptop from the button on the TB15 which also works fine.
However on startup I receive an error message:
"Alert! You have attached an undersized 130W power adapter to you system, which is less than the recommended 180W power adapter" ... message carries on a bit.
Now the thing is both the TB15 power adapter and 7510 power adapter are the same (identical part number) and  are shown to be 180W output.
What's the problem here and what do I need to do ?

A:Undersized power adapter

Any one any idea on this error ? Message appears at Bios post stage... i.e. early on just after switching on.
@Mod - I mistakenly posted multiple times - please feel free to delete duplicates.

4 more replies
Answer Match 44.1%

Hi Guys,

I was hoping someone could help me out finding a power adapter for an old set of Harman Kardon speakers I have. On the back of the speakers it says ac 15v 1.1A so I assume I need an adapter that matches those settings.

Can someone plz help me out finding one that will work and is as cheap as possible.

Thx a bunch.
 

More replies
Answer Match 44.1%

Hi, I need to buy a new adapter for my laptop. The input requirement is 100~220V, 1.7A. I found this adapter with input 100~220v, 1.64A, both output specs are the same. Is this adapter compatible giving the input Amp is lower? thanks.
 

A:Laptop power adapter

You will not have a problem using that adapter.
 

2 more replies
Answer Match 44.1%

Hello,

Recently I purchased a VX1945WM monitor and I was not given a power adapter to run the different integrated features that the monitor offers such as powered speakers and iPod dock among others. I tried contacting Viewsonic, but that was to no avail. If anyone knows the model number or distributor, please let me know.

Thanks,

Matt
 

More replies
Answer Match 44.1%

What is a good, affordable universal power adapter for a laptop. My dad's power adapter for his Dell Inspiron 1545 laptop went out and I need an affordable replacement as I can't pay for a direct replacement right now. The output for the dead power adapter is 19.5V and I believe it is a 65 watt power adapter.
 

A:universal power adapter

Amazon is great for items like this.
Laptop AC Adapter/Power Supply/Charger+US Power Cord for Dell Inspiron 1318 1545 pp25l by SIB $8.98

Do check the Seller Rating. I also look for closest shipper (I want what I want when I want it). You should see all the details in the Ad for what you need, if details are not there, you can move on to the next, or contact the Seller. Either way, they have a very fast return policy if what you ordered does not suit your needs.
 

2 more replies
Answer Match 44.1%

I recently purchased a Del Latitude 7202 Toughbook.
At same time purchased 12V power adapter.
The adapter was shipped separately.  SKU 469-4546.  The power plug did not fit computer.
It is too fat.  Spent 4 hours with tech support and they told me the wrong part was shipped.
They said they would send a replacement.  10 days later I get a package with an HDMI cable in it.
Call support back, was told they would just issue me a credit and I can purchase one online.
I was told I needed part.  450-AAYR.  Web page for that part lists the 7202 as compatible.
It arrived yesterday.  Still doesn't fit.  I am returning it as well.  
What is required to get the correct part?

More replies
Answer Match 44.1%

I have a Toshiba Satellite A215-S4807. I need a new power adapter. (there appears to be a loose connection in it somewhere. It only works when I king the wire a certain way.

This adapter from Targus says that it is compatible but it is only 70W where the original was 120W.

Would the differnce in wattage present a problem in trying to use this adapter?

Thanks very much for your help.

Matt
 

A:Power adapter compatibility

7 more replies
Answer Match 44.1%

The power adapter on my HP Zbook 15u G3 is not recognized. I tried an alternate power adapter, but that is not recognized either. The charge on the battery is almost empty. I've been waiting on hold for 30 minutes with HP tech support. The notebook is only 4 months old.

A:Power adapter not recognized

Support was able to fix the issue. Holding down the power button & mute button for 30 seconds fixed the problem. Thank you 

1 more replies
Answer Match 44.1%

can AC power adapter be used for a Toshiba DC notebook?

Details:
19v,3,42 A

Thanks,
Arun

A:Can AC power adapter be used for a Satellite Pro M70

Your question is pretty confusing.
Can you please post exact notebook model name and model?

Do you need new AC adapter or what?

11 more replies
Answer Match 44.1%

My neighbour was given a second-hand computer and asked for my help setting it up.

It is a Dell Optiplex 755 running Win7.

Currently installed graphics is NVidia Quadro FX 3500.

I looked up the service tag and this is not the original card (Original was ATI HD2400XT).

The issue I have is that the FX3500 is an 80W card, with the PCI-E slot having a max of 75W. On booting I get low power warnings from the NVidia card.

The card has a 6 pin PCI-E connection available for the additional power, but the PSU has no PCI-E power cable.

The only free power cables from the PSU are a couple of 15pin SATA cables. I have seen adapter cables for 15pin SATA to 6 pin PCI-E. Are these any good for my situation?

If not, what are the alternatives? New PSU? Different GFX card?

A:Power adapter cable for PCI-E

Based on what you just told us, one of those adapter cables should work just fine.

5 more replies
Answer Match 44.1%

Hi everyone, been searching the net for a while and still not finding a solution.

The router is connected to a HP laptop already thru the router wirelessly via WPA encryption. I can see my SSID and when prompt to enter my security key/passphrase, it says "windows was unable to connect", and when I click to trouble shoot problems, it says "window can't identify the problem". I'm using windows 7 with the Lenovo. I know the security key is correct because I went into http://192.168.1.1 and checked, and already connects to the HP. Also when I enter the wrong security code it says "invalid security code", it's when I enter the correct code it tells me that "windows was unable to connect to (my SSID).I'm going bonkers over this

A:Lenovo Laptop with Windows 7 won't connect wireless with WRT160N V2.

Try switching to WPA-2 encryption, you should be able to use the same SSID and password.

WPA is an outdated standard and Windows 7 doesn't like it so much depending on the wireless adaptor being used.

3 more replies
Answer Match 44.1%

Currently have my wireless internet coming in to the router which is then connected by ethernet to my xp desktop. Works perfect
Want to replace this "g" WRT160N router with the "n" WRT610N model, when i run through the setup wizard off the disk setup wizard at the final step it says internet connection not found. I can get all my computers networked but no one not even the hard wired computer is setup to the isp or what not are the two setups conflicted or something

please help
 

A:Linksys WRT160N router upgrade to WRT610N WOES

8 more replies
Answer Match 44.1%

H! I have a Motorola modem which we received for our ATT DSL service, and our Linksys router that I have had for a couple years now. It's the best router we have, but we haven't been able to make it work since we got our new Modem. When we had cable, through Cox, everything was just peachy. Anyway, I ran the setup disc again, and wired up everything like I was instructed, and the computer reads the router okay. The status bar icons on the router show that it connects to the internet, but the computer only shows access to local network, and not the internet. I don't know what to do. This router is the best that we have ever had, and it's the only one that I have found that supports our computer, satellite, xbox and ps3. Help please!!!
 

A:Motorola 2210 Modem from ATT and Linksys wrt160n router

Possibly IP Address conflict.

For AT&T default IP address for the Motorola modem is 192.168.1.254.
Default for the Linksys IP address is 192.168.1.1.

Have you changed either one? For them to work correctly they need to be in different subnets. An IP Address of 192.168.y.xx, where y is the subnet and a different number for each device, usually 0, 1, or 2.

If they are in the same subnet, change the modem's IP to 192.168.0.254 or 192.168.2.254. Once you do this you will need to use the new address to access the modem.
You should make sure the router's gateway is outside the DHCP rage of the modem.
 

1 more replies
Answer Match 43.68%

I need to buy a NEW 19.5V 6.7A power adapter for my Dell XPS laptop. Lot's of USED ones out there but I want a new one. Anybody know somehwere reputable online that sells them?

Thanks
 

A:XPS 6.7Amp Power Adapter Dead

This is your specs but you didn't give us the model of the laptop so please make sure it is the same as what is called for here:
http://www.amazon.com/ADAPTER-CHARGER-INSPIRON-LATITUDE-PA-1131-02D/dp/B000MPPB1Q
 

1 more replies
Answer Match 43.68%

I have the 5110nr, I believe. It's got the GTX960m. I am a tech with over 35 yrs. exp in building and overclocking. I realized that the stock charger seems underpowered, at least the one I received with this unit, which I bought used "like new" on Amazon for $850. I was somewhat let down initially upon testing the system for performance, then I found it would double it's performance when on battery power. This indicated to me that the unit was able to draw more current from the battery than when plugged in. Having an understanding of power requirements and electronics, I realized the unit may benefit from using a higher wattage power supply. I bought this baby intending to run "Project C.A.R.S." which is purportedly the most advanced racing sim ever made, with awesome graphics blowing away all current Xbox/PS4 etc. platforms. I found I could run it reasonably well on battery power with the system dialed in using Intel Extreme and PrecisionX for pushing the CPU & GPU to their comfortable limits. Also something I've learned over the years is it's generally best to use the true HP drivers for GPU, manufacturers tend to custom tweak a given driver for their specififc model giving it the best performance even though the revision is never near the most current. Now, the big reveal... I decided t take a chance and buy a used 230watt HP power supply for $38 amazon, then splice the cord so the power adapter would fit this model. I went from not being able to charge while plug... Read more

More replies
Answer Match 43.68%

Hi!

Awhile ago, I started getting this error message when I started up my computer (after the initial Dell screen). It stated:

The AC adapter type cannot be determined. This will prevent optimal system performance.

Strike the F3 key (before the F1 or F2 key) if you do not want to see power warning messages again.

Strike the F1 key to continue, F2 to run the set up utility.

-----

I ignored this problem for awhile by just hitting F1. However, within the last month, it has gotten worse. Instead of this error message coming up when I started my computer - after the initial Dell screen, nothing would come up except a little flashing line in the top left hand corner of the screen, and the computer would not start up passed that. I proceeded to fiddle with the plug that I plug into my laptop from adapter. I would push it harder into the laptop and/or twist it in after I hit the start up button, waiting to see if, after the initial Dell screen, I could get the error message to come up again so I could hit F1 so my computer would actually start up. I really don't know if any of that helped, but I figure if it was the adapter, then I should try something like that. I even blew it the plug and into the socket in the laptop tonight. However, tonight, I almost could not get the computer to start up all the way - I kept getting the screen with the little blinking line after the initial Dell screen and no error message. Eventually, after trying several times, I did get the error ... Read more

A:The AC power adapter type cannot be determined.

7 more replies
Answer Match 43.68%

I have recently rescued a 15 inch viewsonic lcd monitor from being trashed at my work. I did not find the ac adapter for it and would like to use one of my old PSU's to run it. Since the power requirements for the monitor are 12.0V 3Amp, I assume I can just use the 12.0V rail on a standard PSU and attach a tip to it (which I have from a broken universal wall-wort). Will this work? Can't I use any power supply/ac adapter that is capable of supplying 3Amps or more of current as long as it is 12.0V? Thanks in advance.

BTW...I did try a duracell battery charger ac adapter that ran at 12.0V and 2.5A for a short period (as to not damage the ac adapter) and found that the monitor works fine (just has a little fraying on the VGA cable). So I know it is worth converting a supply for it.
 

A:Use a Comp Power Supply as an ac adapter?

A 12-volt supply capable of 3 amps or more is all you need. Just be sure the polarity is right.

I have a 12-port network switch in my shop that's been running off a 5-volt leg of an old computer power supply for several years. At the time, the manufacturer wanted as much for the power supply as I paid for the entire switch and power supply the year before. Old computer power supplies are plentiful around here.
 

2 more replies
Answer Match 43.68%

So.. I see this problem has been posted about before, so I just wanna know what my options are.
This problem actually popped up on me a few months ago, but I was able to remove and insert the power cord a few times and the message would go away and I would be able to charge my battery. But as a month or two passed, it became more finicky, and I had to jiggle with it a little more, but still, I was able to charge my battery and use my laptop wire-free.
Now today, I've been trying all day, and cannot for the life of me get the battery to charge. I get the following message when I plug the wire in.
"The AC power adapter type cannot be determined. Your system will operate slower and the battery will not charge. Please connect a Dell 65W AC adapter or higher for best system operation."
Also, I think its worth nothing that a lot of people mention that this error message comes up while they are booting their Laptops, mine only comes up once Vista is loaded and I attempt to reinsert the cord.
So, I have tried another Dell charger, a 90W one, and the same problem does occur (My original is a 65W). I am planning on getting a different battery tomorrow to see if it is the battery, as this ones usable life was getting quite low, down to barely a half hour per full charge. My warranty, although I'm not sure of the specifics, was not expired when this problem first came up, but is now expired by I would say 2 months at the most.
Oh, I have a M1330, and I have gotten... Read more

A:AC Power Adapter Type Cannot Be Determined

At a minimum, the power jack on the mainboard needs to be replaced - if that doesn't fix it or a competent repair shop tells you it won't, you'll need to replace the system board.
 

more replies
Answer Match 43.68%

Hi

My nootebook turns on only when I connect the power adapter, 30 seconds to turn off, do not see anything on the screen!. Tahnk you

A:Re: Tecra A11-11Z turns on with power adapter only

To be honest I didn't understand your posting very well.
Can you please tell us what happen exactly when you press power button?

What was your last action before you have noticed this problem?
Have you updated BIOS or maye some hardware component?

6 more replies
Answer Match 43.68%

My internet setup is as follows:

Internet > wireless > 4G router > wireless > Main Router > PC (wired) and other devices (wireless)

As you can see the Main Router (which I connect all of my devices to, because it's faster in terms of internal network speeds and has a longer WI-FI range) connects to the 4G router (which is the access point to the Internet) wirelessly.

I want both routers to be wired. However, the 4G router has only a single Micro USB port which also acts as a power supply and the Main Router has no USB ports.

So what sort of (Micro) USB to Ethernet adapter should I buy (suggestions from experience welcome)?

Is it possible to transfer power from the Main Router through its Ethernet port?

If I use an adapter with a separate power supply, will it supply the 4G router through the Micro USB port?

Models:
Main Router: Tenda W308R
4G Router: Is an Infomark Biscuit Mini provided and customized by my ISP.
 

More replies
Answer Match 43.68%

Seeing as my PSU is limited in the cable department i had to purchase a 4 pin to 8 pin adapter to power my PC.

Do i have to connect both the 4 pin and molex cable's to it or is it ok just connecting the molex cable like i have done?.

StarTech 6 inch 4 Pin to 8 Pin EPS Power Adapter with LP4 - F/M: Amazon.co.uk: Computers & Accessories

A:StarTech 6 inch 4 Pin to 8 Pin EPS Power Adapter with LP4 - F/M

>> Delete my response and defer to others below <<

Regards,
GEWB

9 more replies
Answer Match 43.68%

Hello, I live in Montreal, Canada and I am having problem with my mcbook. The power adapter does not seem to be working. i have come across a website for a company based in Montreal;  http://www.applerepairmtl.com/mac-pro/; can anyone tell me if its good ?

More replies
Answer Match 43.68%

I have a Dell Inspiron 9100. I have checked the adapter/charger and it is putting out he correct 19V.

However, the LED lights on the battery do not indicate anything. After charging for 10 hours, I push the power button and nothing happens....no screen activity, whirling, noise, etc.

I have tried starting with adapter connected and not connnected.

Could a battery be so dead that the computer will not turn on?

Or is it the MB or bios?

Thanks.
 

A:Dell will not start, power adapter okay

Try removing the battery and starting the laptop using only the AC adapter. If you still get nothing, the motherboard is most likely bad
 

4 more replies