Tech Problem Aggregator

broke wifi switch in the off position

Q: broke wifi switch in the off position

hello almost a year ago i was getting mad at my internet and turned the wifi switch on my laptop off so i cud turn it back on... when i turned it off i had inadvertently broke the switch in the off position and for a few weeks had no internet while i searched frantically to find a solution... eventually i just gave up and bought a usb wifi device to override the switch... recently i have lost this usb and i was wondering if there was a cmd command or something that i cud do to manually turn it back on... i am currently using windows vista on a computer around 3 or 4 yo and once again frantically searching for a solution... pls help with any info possible.

A: broke wifi switch in the off position

What make/model is the computer?

If it is a slide switch and you broke off the part that sticks outside the case, you might be able to use a toothpick or other small stiff object to reach through the slot and slide it to the ON position.

3 more replies
Answer Match 81.06%

I have a Toshiba satellite L350D 01M laptop. My warranty period is over and I wanted to clean out the fans etc... and I have taken apart many laptops in the past but man it was hard to get all the connectors from the keyboard etc hooked up without unplugging another one because of the lack of wiggle room, how the guys at Toshiba put them together i will never know anyway i finally managed to get them all hooked up and the case back together but the wifi radio switch next to the SD slot was not aligned properly and rather than go through the nightmare of hooking it all back up again i forced the switch a little too much well actually a lot too much as i busted the dang thing right off.

so now i can't switch on the wifi which ain't that bad for home 'cause i have a wired modem but when i am out and about i need the wifi capability. someone suggested bridging the two connections i can see inside (a guy at staples) but that if it did work each time i shut it down i would have to bridge it again, well I tried that and I did something wrong as the whole system shut off like a lightening bolt and i thought i fried the motherboard as i couldn't get it to turn on, but i unhooked the battery unplugged and held down the power button for ten seconds then i plugged it back in minus the battery and luckily it worked, there is no way i am going to try that again and if i don't have to (i can't afford it anyway) is there anyway i can bypass the hardwire switch... Read more

A:Solved: I broke off my wifi switch on my laptop

13 more replies
Answer Match 62.58%

One of the windows on the taskbar just switched position from being on the far left end of the taskbar to go into far right side of the taskbar. is this normal or is this some virus or something?

A:taskbar window position switch

Hi
This tutorial it will help you to understanding and usage of the taskbar.
Taskbar Button Grouping - Enable or Disable

1 more replies
Answer Match 59.64%

My wireless accidentally got broke on my compaq nc8430 is there any other way i can turn my wireless capibility on anything will help because this laptop is the only way i can get my school work done i bout it for school a while back please help.

More replies
Answer Match 59.22%

I have a wireless router connected to my modem, and ALL PC's connect to that for internet.

I also have a gigabit switch I use to transfer data in between several of the machines. I do it quite often and I don't want it eating up the wifi bandwidth.
I have done it before, but it has been a long time and I cannot remember how I forced internet traffic over the wifi and local traffic through the switch
Is the only way to do it to specifically tell Windows to use the IP address of the LAN connection? I know it will work that way, forcing local traffic directly to that IP, but I seem to remember there being an easier way to do this.

Thanks.
 

More replies
Answer Match 58.8%

This is for an Antec case, where the inner, plastic coil on-off switch has come loose. The plastic pin retaining the flat, spiral coil on a side has broke (poor design, which is surprising for this make). The marginal mini pin snapped == case front is practically trashed. And if case front is no longer available, of course all components must be moved to fit inside another new separate case.

So looking for the best glue I can find to secure it back.

I hessitate to shoot glue, since every time the switch is depressed from the outside, finger pressure will be applied.

Anyway, what would be the best high strength glue for bonding plastic-on-plastic?
Is the glue gun better?

(notice that certain glues write out certain types of plastics under their recommended applications)
 

A:plastic pc case switch broke - looking for best glue

It is difficult to recommend a glue for this purpose for several reasons; but, my experience with vulcanizing plastics goes back over 50 years when I was assembling plastic model cars and I learned the difference between vulcanizing glues and what I would call surface glues.

Plumbers' glue for plastic pipes vulcanizes the plastic, meaning that it melts the plastic on the opposing surfaces and bonds them together with a chemical reaction. If done properly, the glued joint can be stronger than the rest of the object.

Read the label and apply the instructions as well as can be done for such dissimilar surfaces.
 

3 more replies
Answer Match 56.7%

Hi, I have a Gateway NV52L15 notebook and I am having problems with my WiFi access. I have Windows 8. My wireless networks are not showing up. When I troubleshoot the network adapter, I get a messAge that reads that my wireless capability is turned off. When I go to the Gateway Device fast lane, my WiFi is on. But when I look in networks it as shows WiFi off and I am unable to turn it on that way. When I go to wireless devices in pc settings, the toggle button for the wire device is grey, therefore I am unable to switch it on- It used to work.

Also, while in the Gateway Device fast lane, when I press the F3 key the airplane mode goes on...the WiFi goes off...by comes right back on. Please help...

More replies
Answer Match 55.44%

Cool story. I installed Oracle VM on windows xp. Hoping to use the VM for internet, and protecting my real OS as such.

NOPE.

As soon as I tried to include an adapter in Oracle, and ran it it screwed up my computer.

Tried reinstalling windows. That didn't work.

Tried reinstalling the WiFi driver and that didn't work either.

Instead of connecting with Intel PROset... that taskbar icon stays with a red X saying, "No supported WiFi adapters available in the system."

it connects with windows default network connections, and is super slow. also every time I log back on it adds a number to the icon.... what i mean is that it now says, "wireless connection 5"

and before it said "wireless connection 4"

it's a gateway MX-6959
Intel(r) PRO/Wireless 3945ABG
windows xp media edition 2002 sp3
oracle VirtualBox 4.2.2 (uninstalled this FKin' trash.)

anyone know what I should do to restore my settings to the proper configuration to get my internet to work proper again?

A:HELP. WiFi Broke... omg - don't install oracle VM.

Oracle VM uses the Ethernet connection and not the wireless for internet. Go to Start/Run and type ncpa.cpl and press enter. In the Network Connections, you should have a Host Adapter (virtual Ethernet Adapter) for the VM, you can right click this and Disable it. If you tried to install a Wireless Adapter in the VM, boot into the VM and uninstall it and restart the VM.
Everytime you reinstall your Wireless Network Adapter, Windows assigns the next # (ex) 1,2 3 etc. There is a setting in the Registry, but if you can live with it I wouldn't mess with it.
Now in the Host machine, go to Start/Run and type appwiz.cpl and press enter. Here uninstall the WiFi adapter driver, and restart the computer. If there is no software there, go to Start/Run and type devmgmt.msc and press enter. In the Device Manager right click the WiFi adapter and Reinstall the driver. Or Right click the Adapter and Uninstall it, restart and then Reinstall it. See if that helps.

2 more replies
Answer Match 55.02%

My laptops touch panel is not working. So now, i cannot switch on my wifi in my laptop.Is there any alternate way (like drivers) to switch on the wifi in my laptop? Model: HP 6510b Compaq

A:Switch on wifi without using Wifi touch button, since its no...

HI Michael, If you go to the Control Panel, and select the "Network and Sharing Center" item, in the bottom left of the screen there should be a "HP Wireless Assistant" link in the "See Also" section. Click that, and it will allow you to enable the wireless adaptor. That may achieve what you need to do. Regards,John

9 more replies
Answer Match 54.18%

My computer is a dell inspiron 14z.

So my wifi was working ok before I upgraded to Windows 8 but afterwards seemed to not even realize it had wifi capabilities. I looked at the Wireless network adapter thing in the device manager and it had a little error icon next to it.

Here's some pictures of the error and device manager that might help maybe.

I've tried updating the driver but it just says that its all good and up to date.

Dell wanted me to pay 120$ for a single customer service session.

I'd be so happy if you guys could fix this.

you guys are awesome thanks
 

A:Dell Inspiron WiFi broke after windows 8 upgrade

120$? to fix a driver issue? That is extortion in my eyes lol.

Anyway I had a quick look on the dell support site and found there are 3 different models for Dell Inspiron 14z Could you tell me which one it is? Also try navigating to the driver downloads page and downloading the wireless network drivers for your model and installing them. Pic Attached

http://www.dell.com/support/troubleshooting/uk/en/ukbsdt1/Product/inspiron-14z-5423

http://www.dell.com/support/troubleshooting/uk/en/ukbsdt1/Product/inspiron-n411z

http://www.dell.com/support/troubleshooting/uk/en/ukbsdt1/Product/inspiron-14z

Had a look at the drivers on each of the models and they only seem to support 64bit Versions of Windows 7 & 8, Do you know if you have 32bit or 64bit edition of windows 8? If you have 32bit then the drivers for the hardware probably wont work.

If you don't you can check it by following this easy guide (I would walk you through it but I havent used windows 8 yet) http://pcsupport.about.com/od/windows-8/a/windows-8-64-bit-32-bit.htm
 

3 more replies
Answer Match 53.76%

Hi guys, I recently bought a computer off of my friend. He told me before hand that the wireless internet didn't work on the computer's main adapter, but he gave me an external usb adapter that lets me go online. He told me that he screwed up the computer's wifi by trying to hack his neighbor's internet. There was a weird program called hamachi which i think may have something to do with it. He can't remember what he did to mess it up. Is there anything you guys can recommend that could help me out?
Thanks,
James
 
Edit: I'm running windows 7 64 bit and the computer is a laptop

A:My friend broke my wireless adapter by trying to hack a neighbor's wifi

Just do a Reinstall of Windows 7 that came with the laptop.  If your friend did not give you the restore DVD's, contact the computer manufacturer, and they can send you a set for around $25.
 
You are allowing yourself to be open to anything that your friend may have planted on that machine, to eavesdrop on you, or even have it loaded with so much malware, that you definitely want to do a clean install, before you use it.

9 more replies
Answer Match 49.98%

I changed my screen panel due to damage and with the new panel i d not have the wifi / antenna button. how do i switch on wifi now?

More replies
Answer Match 49.98%

I have hp 15 ac650tu. I cant use its wifi. I cant switch it on too. Please give me solution.

More replies
Answer Match 49.56%

I was playing a game on my laptop and decided to switch from wifi to ethernet. I plugged in the ethernet and turned off the wifi switch to ensure it switched over, but later when I tried to turn wifi back on, I see the wifi on/off switch is grayed out.

I went to my device manager to check for wifi network adapter driver updates, but everything seemed pretty up to date.

Any recommendations on how to fix this? Or at the least another method of turning the wifi on, like through command prompt or something?

Thanks

A:WIFI on/off switch is grayed out

So to fix this what I did was hit the airplane mode key on my keyboard. The wifi switch in the pic I posted would stop being grayed out for about 5 seconds, and I had to switch it on in that time.

I'll note that flipping the airplane mode switch right above the wifi switch didn't do this, so I don't have a clue how it worked out.

1 more replies
Answer Match 49.56%

Hi guys,

I'm new to this forum and my apologies if I have posted in the wrong field with this query...

I have a customers Packard Bell Easynote MX37 laptop that I have installed Windows 7 on... Original OS Vista Home Premium.

The problem I am faced with is the WiFi switch.

The WiFi switch will activate itself on start up and enable wireless connection, but if the switch is pressed it disables wireless and stays disabled, no matter how many times switch is pressed. Once laptop is restarted it will become active again...

I am stuck on how to proceed with this problem and any assistance is greatly appreciated.

Thanks guys.
 

A:WiFi switch disables...

8 more replies
Answer Match 49.56%

how do you tell xp which program you want it to manage your wireless network? a friend has installed d-links software and it has taken over managing the wireless connection. I would like to undo it and make it use windows built in wireless managment software

A:how to switch which which app is managing the wifi

If you goto Add/Remove programs and remove the DLink program it will probably revert to the original windows xp wifi manager.

2 more replies
Answer Match 49.56%

Hi guys,

I'm new to this forum and my apologies if I have posted in the wrong field with this query...

I have a customers Packard Bell Easynote MX37 laptop that I have installed Windows 7 on... Original OS Vista Home Premium.

The problem I am faced with is the WiFi switch.

The WiFi switch will activate itself on start up and enable wireless connection, but if the switch is pressed it disables wireless and stays disabled, no matter how many times switch is pressed. Once laptop is restarted it will become active again...

I am stuck on how to proceed with this problem and any assistance is greatly appreciated.

Thanks guys.
 

A:Wifi switch disables...

Did it work as expected with Vista? Maybe there is a Packard Bell WLAN utility you need to download from their web site? If no Windows 7 one maybe a Vista one that will still work.

Is the switch a toggle or slide switch?
 

2 more replies
Answer Match 49.56%

So the wifi switch on my computer is broken off, although i am unsure how it happened. The places I have taken it to with questions have only told me expensive solutions for it such as having to replace the entire motherboard (which seems strange to me just because of one switch) anyways, I have wireless internet in my house, but cannot use it on my laptop so for anything that involves internet connection the laptop is useless. I also bought one of those netgear wireless usb adaptors and am still not able to get internet.

Any help would be appreciated! Thanks
 

A:Wifi Switch Not Working

I may be wrong but the wifi switch should not affect an external USB adapter. What were the issues you were having when you installed the Netgear Wireless USB? Did you disable the internal wifi adapter (either in Windows or BIOS) prior to installing?
 

1 more replies
Answer Match 49.56%

Hi All,

I have a laptop (Lenovo Thinkpad) that is mounted in a docking station. In my house I have wifi, the docking station is connected to the router via hard LAN.

I have prioritized my connections to give preference to LAN over wifi (as I obviously prefer the fastest connection).



The Network sharing center now tells me I am connected to both LAN and Wifi, but the system tray tells me Wifi. How do I know through which I am now connected and how to I prioritize LAN? Please don't tell me to manually enable / disable ;-)



Thanks a lot!

M

A:How to switch between wifi and ethernet

Try ipconfig and see what your lan ip is
and then try
pathping 8.8.8.8
and if it goes threw you lan card ip first you will know it's working the way you want

1 more replies
Answer Match 49.14%

I have a Lat 5470 where I am trying to turn wifi on/off at will. I found where i can lock/unlock the FN active key by using FN + ESC key but when I press FN+PrtScr to turn wifi on/off, the only thing that turns on/off is Bluetooth.
Yes I have enabled this functionality in the BIOS but no change.
Thank you

More replies
Answer Match 49.14%

Hello I just bought a brand new computer 3 days ago. Haven't been using it that long. It's an HP Envy 810qe or something like that. The first day I played on it 77 windows updates were downloaded.

The computer has built in Bluetooth which I love but I noticed it was always-on and was wondering if there was an on/off switch. I searched Google and seen there is an on/off switch in PC Settings, PC Devices, Bluetooth. Unfortunately I do not have this. Also under PC Settings and Network I do not have an on/off switch for the wifi. I also don't have anything in PC Settings called Wireless. I talked with HP support (since I just bought this computer) their only option was to do a System Restore or Recovery. I talked to Microsoft support and their only option was to pay for a premium membership so they could use their 'advanced tools' to scan my system and find out the problem. (which is my long history of dealing with computers and support their answer would have probably been the same which was System Restore or Recovery, at which who even knows if this is going to fix the problem)

So now I come to this community my first time here (wave) asking for assistance. I temporarily disabled my Bluetooth in Device Manager because I don't know if it's safe to have it constantly on if I'm not using it. I've seen on here there are other people who have had the same problem but I didn't see a definite solution on the couple threads I read. Also just before disabling my Bluetooth I ran HP s... Read more

A:Bluetooth and Wifi no on/off switch in PC settings

Hi summerbear. I can try something that works on my MSI laptop (a great brand BTW), and I think most of todays' laptops.
Usualy there's an allin1 manager to all of the options you mentioned, and it is accessible through the start line in windows (at the bottom). Most of the time you don't see all the icons of programs running, and there's a little upward arrow in far right side of the start line, that if clicked reveals sound, storage, and allin1 managers installed in your system. In my laptop this manager program that includes control over volume, wi-fi, and bluetooth, is called SCM. I'm not sure that HP's has the exact same program but there's supposed to be some type of allin1. If you don't find any try typing "Bluetooth" in windows search (through the start button), and shutting down wi-fi is also possible by clicking the network bars in the far right, thus accessing the list of nearby wi-fi networks, choosing the one you're connected to, and clicking "disconnect".
Hope I helped, goodluck.
Amit.

5 more replies
Answer Match 49.14%

I have a 6 month old Yoga 500 and this is the second time this has happened.  The last time I was resigned to taking it back to the shop and the day I was going to do it I turned it on for one last time and it was working perfectly again! Here are the symptoms  Fan running at full speedKeyboard not responding - touch screen working fine and can log in and use WindowsWiFi showing as off with Red Cross on wifi symbol.  In settings, option to turn it on is greyed out.  Ive carried out a Windows restore to a date last week when everything was working fine I've disabled and enabled the wifi card through device managerI've uninstalled and reinstalled wifi card drivers The last time it happened I also carried out a full factory restore but this didn't work.  As mentioned above, it just started working again.  So I'm not going to go through the hassle of trying that again. Any suggestions before I take it back to the shop?

More replies
Answer Match 49.14%

Hi,
I run an Ethernet cable to my modem for my Windows 10 PC. But unfortunately I have a lot of drop outs where the internet just stops (something I am taking up with my provider) and I have a pocket wifi to use as a back up.

My PC can find the wifi and connect but the only way I can get it to connect is by pulling out the blue Ethernet cable from the actual pc. (When I say connect, I mean it is "connected" already but not in use, the small box appears for the ethernet cable rather than the wifi icon)

I would like to know if there is a way to either run the wifi simultaneously with the Ethernet cable plugged in or if there is a way to "turn off" the Ethernet connection from my pc when it goes down, so that I dont have to keep unplugging it.

I am not very technically minded and am worried if I go into advanced network settings etc that I might not be able to get the Ethernet working again once it is plugged in and back up and running.

Any advice would be appreciated, thanks.

A:How can I switch to WIFI from Ethernet instantly??

You can have both plugged in and still work. Each NIC is assigned a metric and the NIC with the lowest metric will be used. If in your are the wired NIC is still seen as available but in fact it's having problems the computer will still try and use it unless you unplug the cable. If your computer supports a feature called LAN/WLAN switching that may work in your case that may work or may suffer from the same problem in which the wired NIC is still detected as connected and it won't switch. If you are only having an issue with the wired connection why not just stay on wireless?

8 more replies
Answer Match 49.14%

I was using Windows 7 Home Basic preinstalled with the laptop since 2011. The laptop was working fine. After upgrading to Windows 10 the WiFi and Bluetooth is not working. Tried help from Microsoft remotely. According to them the drivers are not working and there is no updated drivers available for Windows 10 on HP website. The driver installed presently is "Broadcom 4313GN 802.11b/g/n 1x1 Wi-Fi Adapter".Please help and advise whether to stick with Windows 10 or to roll back to Windows 7 as I have an option to purchase a removable device to use WiFi and Bluetooth.I love the lightness of the new operating system. Please help!!!

A:Not able to switch on WiFi and Bluetooth after upgrading to ...

Hello @Banti2?, Welcome to the HP Support Forums! It is a great place to find the help you need, both from other users, HP experts and other support personnel. I read your post about the Windows 10 upgrade, and wanted to assist you!You can use the Go back to an earlier build option, in your System Settings: HP Notebook PCs - Upgrading to Windows 10Once you are back to your original Operating System, check to see if you are experiencing the same issue. If not, then you may consider holding off on the Windows 10 upgrade for a few weeks, until drivers can be updated. However, if you are able to get the WiFi and Bluetooth to work, using an external device, then you can continue to use Windows 10.  Keep in mind, that the rollback option is only good for the first 28 days, after installing Windows 10. Please let me know if this information was helpful by clicking the thumbs up below.Regards!

2 more replies
Answer Match 49.14%

When the WiFi button (F12) is pressed the LED show red and a message on-screen briefly says "Flight Mode ON" and the network connection icon in the notification area shows a red X. - this is expected - however When I press F12 the on screen message does breifly display "Flight Mode OFF", but the LED stays orange and WiFi is disbaled. If I click the network icon in the notification area the panel that appears says Flight Mode OFF, WiFi (OFF). I simply cannot re-enable the WiFi with the F12 key. If I go to Computer->Properties->Device Manager, select the Wireless Adapter I can switch the WiFi back on by going to the Advanced tab and selecting Radio->Enable. If I do this the let then goes white and WiFi is OK. So what is going on - why can't I simply toggle the WiFi off and on with the F12 key. Why to I have to resort to the device manager to switch it back on again?

A:New HP Pavilion G6 - F12 switches OFF WiFi but won't switch ...

Solved my own problem - if it help others ....the WiFi Driver update dated 25/09/12 caused the problem in my case.Right click on 'Computer' select 'Advanced' and open Device manager. Locate the WiFi Adapter and choose the 'Roll back driver option' to restore the previous driver - worked for me. You think someone would test drivers better than this !!!

9 more replies
Answer Match 48.3%

wifi switch on asus k55v not working. it used to work just fine till yesterday but when i tried it today the switch didnt work.the wifi is working though i just have to troubleshoot the network and sharing and it applies a fix to switch on wifi adapter then it works but the function-switch(f2) is not working

A:wifi switch on asus k55v not working

Hi gsk ... Welcome to Seven Forums ... Download the Function Key Software from the Asus website

1 more replies
Answer Match 48.3%

Hi, I have a Pavillion g6 - 1301TX running on windows 7, 64-bit. I cannot switch on my wifi and change the orange light. ive searched solutions for this, and most seem to be solved by installing drivers for the wifi card. and most seem to be solved by going into Device Manager / network adapters... and so on. but as i get to this stage my laptops device manager does not recognise a wifi card as being there!??? PLEASE HELP!?? I can only connect using ethernet. Kindly send me the drivers of wi fi for my notebook at my email id [email protected] Thanks  

More replies
Answer Match 48.3%

whenever i switch users, the internet connection gets disconnected on the previous users. Is there anyway i could set it so when i switch users, the previous user is still connected. like connected on aim. and switch users and ill still be on aim.
 

A:wifi connectiong disconnected during user switch ?

11 more replies
Answer Match 48.3%

Hi,

I think I know what I want, but I just wanted to check before I splashed the cash and made the wrong choice!

I have a Humax Freesat recorder and a Panasonic Blu-Ray player. Both of which have services that need internet access, but neither are WIFI enabled & are the wrong side of the room to be connected via cabled ethernet.

I believe that what I need is to wireless access point? I'd like one with a built in switch as well, as most seem to only come with only one port. The one I found has four, which would be useful as I could replace the poor wireless Xbox 360 dongle.

The one I was looking at was http://www.amazon.co.uk/gp/product/B004JV42A0/sr=1-1/qid=1325091993/ref=olp_product_details?ie=UTF8&me=&qid=1325091993&sr=1-1&seller=. This seems very cheap.

Can anyone tell me if this will do what I want & whether there is anything better without spending a fortune?

Many thanks in advance
Tom
 

A:WIFI Network Access Point with Switch

6 more replies
Answer Match 48.3%

Hi.

I have a pesky little brother who keeps switching off the WiFi switch on my laptop when I leave home without some downloads on. He does so that he can hog up all the bandwidth for himself.

Is there any way I could disable the WiFi switch so that my WiFi stays on at all times? I have a Lenovo Y560.

Thanks.

A:Disable WiFi hardware switch on laptop

If he can't turn off the WiFi what will stop him from just powering the system down?

There may be a way to catch the key using AutoHotkey. You would have to have a script running that echos the vk key codes as each key is pressed. Once you know the code for the WiFi key you can just intercept it with a one line script.

But he could still just close the program running the script or hold down the power button.

9 more replies
Answer Match 48.3%

I have a 3com Switch 4400 and a netgear BT internet router / modem (4 port)

BT router > 3com switch > PC's

I have around 10 Pc on my network, 7 of them are connected to the 3com and the rest via wifi.

i need the 3 com router to issue the ipaddrsses and give access the the internet via the BT modem / router / AP.

I have tried looking on many forums but no help, i can get the 3com to issue the ip addresses, but then i have no internet. Or set the d.gateway to the bt router but then i am unable to have the 3com to issue the ipaddress.

please if anyone can help
 

A:Bt wifi router/modem & 3 com Switch 4400

6 more replies
Answer Match 48.3%

Hi guys, I have a strange problem with one Lenovo ThinkPad Edge E145 notebooks. At first I was not able to start in windows the wireless but after multiple uninstall/install/update of the drivers I managed to do it. Still Windows shows WiFi on but in the same time off and I can't see any WLAN networks. The windows diagnose of the WLAN adapter shows - wireless capability is turned off The Lenovo Diagnostic Tools shows - Warning Hardware state is off I've checked BIOS, check the settings of the card and I don't have a hardware switch on the notebook. Is there any way that I could "reset" this lock or enable it somehow? Thanks in advance I forgot to add that the notebook is with Windows 10 64bit and there are not much apps and drivers for it.

More replies
Answer Match 48.3%

The title basically spells it out. I would like to know if leaving my WiFi switch on my laptop on all the time is a bad idea? Would I see any performance hit because my system is constantly looking for a WiFi signal?

A:Is it alright if I leave my Wifi switch on all the time?

I leave my switch on all the time and have never seen any performance hit. It would be mighty inconvenient to keep it switched off, then switch it on everytime I need to use the internet.

And your system is not constantly looking for a wifi signal. Once you've connected to your home network, it would stay connected to that.

9 more replies
Answer Match 48.3%

...but it's not.

Hi, I'm Antonio. About a month ago, while I was doing work, I tried to access Ubuntu from my jump drive to look at a certain application (don't remember what). Couldn't get the wifi working in Ubuntu (as had happened in the past), so I gave up. When I got back to Windows 8, the wi-fi was not working in Windows, either! It's still not working. Despite the wifi switch being clearly in the "on" position, it doesn't think the wifi is on. Toggling the switch with the Device manager open shows the Bluetooth drivers popping in and out, so the switch is physically working, at any rate. The wifi drivers stay put, and Device Manager thinks they're working fine.

Sony Vaio S series laptop (VPCSB11FX). Windows 8, 64-bit. I've tried:

-Deleting and re-installing drivers.
-Deleting and re-enabling.
-Doing a system refresh.

If I go back into Ubuntu (as I'm doing now), I can fire off an "rfkill unblock all" command, and the wifi works. Hardware swtich and all. How do I get Windows to think my switch is on, and that my hardware is working?

More replies
Answer Match 48.3%

I have experienced several sudden blue screen crashes, with apparently no advice. After several different conditions trials I reckoned it occures when the WiFi switch is on. So, it should be associated either to Bluetooth or Wlan.

Any suggestion how to go deeper? apparently I have last drivers (Windows 7 64)
Thanks, Guido

A:Tecra S11 - Blue screen when WiFi switch is on

Hi buddy,

Have you already checked the BIOS if you have installed the newest version? If not check this on Toshiba website and make a BIOS update. Maybe it helps?

But I had a similar problem last year and the solution was exchanging the WLAN card.

I think your Tecra S11 should be still under warranty and in such cases the repair would be for free. :)

2 more replies
Answer Match 47.88%

DELL Latitude E6510 wifi switch is not working

More replies
Answer Match 47.88%

Hi guys, I have a strange problem with one Lenovo ThinkPad Edge E145 notebooks. At first I was not able to start in windows the wireless but after multiple uninstall/install/update of the drivers I managed to do it. Still Windows shows WiFi on but in the same time off and I can't see any WLAN networks. The windows diagnose of the WLAN adapter shows - wireless capability is turned off The Lenovo Diagnostic Tools shows - Warning Hardware state is off I've checked BIOS, check the settings of the card and I don't have a hardware switch on the notebook. Is there any way that I could "reset" this lock or enable it somehow? Thanks in advance
 
I forgot to add that the notebook is with Windows 10 64bit and there are not much apps and drivers for it.
 
P.S.
I found the solution. I removed the BIOS battery for 5 Min and after this everything worked. Still if someone knows another approach it will be better.
 
 
Moderator comment: Model added to subject for clarity.

More replies
Answer Match 47.88%

I am unable to find the switch or keyboard key to enable WIFI on this system. I looked all around the cover and keyboard. Please help.

More replies
Answer Match 47.88%

Ciao,I have this problem with my ThinkPad X220 since I upgraded it from XP to Windows 7.If I switch off the wireless radio switch on the left, it works instantly and disables all radios (as expected). But in order to have the radios work again I can't just turn the switch back on. It never works. I have to restart Windows and then it works.Is there anything I can do to not restart Windows?Thanks 

More replies
Answer Match 47.88%

i Bought a  dell precision m4800 it came it windows 8 i updated it and now my wifi switch is not working it does'nt turmn off and now i can't turn the bluetooth on as well, it says that you need to turn on the wireless hardware but it is already on

A:Wifi switch not working Dell Precision M4800

Hi Shayashkar,

Have you checked first of all that the wireless switch is enabled on the right hand side? Also go in to the BIOS (F2 on startup) and check that the Wireless Switch is set to "ALL" and the Wireless Device Enable is set to "ALL"
If it is still not turning on, I'd suggest updating the Wireless Driver. Follow this link [View:] 
and choose Network and download the latest driver for your WLAN card. If you know the Service Tag enter that and it will list the drivers for your particular configuration. Let me know if the issue is resolved or if you are still having issues.

5 more replies
Answer Match 47.88%

I have an Asus U50F Laptop and the external wireless switch to turn the WiFi on/off isn't working. The splash screen will show up indicating I turned off my WiFi but then nothing happens and I still have a wireless connection.

A:External Asus WiFi Switch Doesn't Work

I managed to fix this by installing the Asus wireless console 3. Delete this thread please.

4 more replies
Answer Match 47.88%

Dear Forum,
I am working in an organization and i am IT support engineer. comimg to issue...we do have multiple SSIDs in our organization and this is happening to some of the users who are using HR(for example) SSID. wifi profile is missing everytime, when user switch from home wifi or another network. this is happening only for one SSID(HR) among 6 SSIDs. where, it(HR) uses the EAP-FAST module. And user can access internet only through this particular SSID(HR) and remaing SSIDs are used by other important users. when user comes to us with this issue, we are adding it manually in Network sharing and Center>Manage wireless>Add . when user connects this SSID(HR), it takes windows login ID and password as credentials. there is no issue with other SSIDs.
thanks

More replies
Answer Match 47.88%

Hey - my hardware wifi switch keeps breaking, thinking it's in the off position. I can temporarily fix it by opening up the laptop and jigger the connections, but this takes a full hour every time i do it, and it only seems to last a month or so, then it breaks again and i have to open up the computer again.  Is it possible to simply disable the hardware switch? 

A:Disabling T430 hardware wifi switch permanently

Welcome to the forum.
 
oxgaard wrote:
 
Is it possible to simply disable the hardware switch? 

Have you considered soldering a jumper across the switch?

2 more replies
Answer Match 47.88%

How can I fix this? When the side switch is in the "Off" position, my laptop is in Airplane mode and refuses to leave. When the switch is in the "On" position, I am told that the internet access is disabled due to the switch being turned off. I have tried disabling the switch in bios and this did not work. I do not know any potential solutions.

More replies
Answer Match 47.88%

Good afternoon,

I have a networking question.

Can I plug a 5 port Ethernet switch to my DSL modem, connect 2 PCs to the switch, run a cable from the switch to the far end of my house, connect a Wireless n router for WIFI access for my laptop/iPhone and connect another PC, one BluRay player and a couple DirectTV DVRs to the wireless router? Please see attached diagram.

Your help will be greatly appreciated.

Kind regards,

 

A:Solved: Ethernet Switch/WiFi Router Connectivity

12 more replies
Answer Match 47.46%

I have succesfully used a Hyper-V virtual switch connected to the wireless adapter in my laptop. All my VM's could access my LAN independently, and could get an ip address from the DHCP server. This means, AFAIK, that my wireless adapter can and does opererate in promiscuous mode.

This worked up to build 10586. Today, I upgraded to build 11102, and this setup no longer works. It appears that wifi adapters are simply not supported with Hyper-V virtual switches. Bummer.

When you try to configure a wifi adapter in a virtual switch, it is not simply grayed out, or otherwise made impossible, but it tries to go ahead and then gives an error message (see attachment)

This does not make sense. There is no other bridge or switch configured.

I found two work-arounds:

- configure the wired ethernet adapter to the virtual switch, and create a bridge connection between the wired and the wifi adapters. For me this does not work, because I get an other error trying to create the bridge connection, which I will report in an other thread.

- use ICS. This works, but has the huge disadvantage of having a NAT layer between the VM's and the rest of my network.

Has anyone experimented with this, too?

Bart

A:Wifi adapter no longer supported in Hyper-V virtual switch

I am now at build 14257. I am still not able to create a virtual switch which connects to my wireless adapter.

Bart

0 more replies
Answer Match 47.46%

I have an HP Zbook 14. I have had this laptop for almost a year and never had a problem connecting wireless.
The other day, my laptop froze up and was unresponsive. I rebooted it and noticed immediately a message about a hash mismatch, but the laptop continued to reboot. After coming up, I could no longer connect wireless, even though the light is on. Troubleshooting
efforts keeps saying to enable the wireless switch, which it is on.
I have done numerous tasks, disable then enable, press the wireless button on and off. Currently I am hardwired in and thought if I unplugged the Ethernet cable, it would pick up the wireless but it did not.
Any suggestions or advice?

Thanks

More replies
Answer Match 47.04%

I will be keeping the wireless turned off most of the time on my desktop, as I use it for live pro audio. Is there a registry hack to put the switch in there, even if the computer is not a laptop???

A:Show airplane mode switch on wifi menu on desktop computer

Airplane mode: ms-settings:network-airplanemode

Hi, you can use the above when creating a new shortcut, if that's what you need- I'm not sure.
Remember you can access Flight Mode ('Airplane Mode') from the Action Centre (icon in system tray in the taskbar).

Here are some more FYI:

Manage Wi-Fi: ms-settings:network-wifisettings


Mobile hotspot: ms-settings:network-mobilehotspot

Wi-Fi: ms-settings:network-wifi

6 more replies
Answer Match 47.04%

I will be keeping the wireless turned off most of the time on my desktop, as I use it for live pro audio. Is there a registry hack to put the switch in there, even if the computer is not a laptop???

A:Show airplane mode switch on wifi menu on desktop computer

Airplane mode: ms-settings:network-airplanemode

Hi, you can use the above when creating a new shortcut, if that's what you need- I'm not sure.
Remember you can access Flight Mode ('Airplane Mode') from the Action Centre (icon in system tray in the taskbar).

Here are some more FYI:

Manage Wi-Fi: ms-settings:network-wifisettings


Mobile hotspot: ms-settings:network-mobilehotspot

Wi-Fi: ms-settings:network-wifi

0 more replies
Answer Match 43.26%

I have gotten blue screen of death and i'm just trying to find things that could be wrong. i stumbled across this unknown file in my device manager, and it is saying unknown and not allowing me to update the driver, Hoping anyone can help. I use a Belkin wireless router, but i have my internet through an Ethernet cord into my computer.
Thank you.

More replies
Answer Match 42.42%

Hi guys! I'm new to this forum but I come here in the hope that you can help me figure out why is it that when I connect my TiVo to my linksys router(configured as a switch), I STOP HAVING WIFI! Don't know why... As soon as I turn the TiVo box off the wifi starts working(as soon as I reboot the router)... The TiVo works perfectly, no breaks and perfectly connected to the network, but that specific router switch where it is connected, stops functioning though wifi(can't even connect!)

The setup I wish to use(and that is currently working) is:

Modem router(Thomson)---through cable to another router(with dhcp and nat disabled)airporttime capsule)--- through cable to another router(linksys) also with dhcp and nat disabled... Everything works when not using the TiVo box...
The only switch that stops working is the linksys(the one to which the tivo is connected)
Help me pleAseeee
(I'm from Portugal-using an internet tv service)
 

More replies
Answer Match 39.48%

Need to no if I have this right

they have a dsl modem going to a Linksys router to a 24 port switch then to a little 4 port switch. sure, so then Would it be modem to router then router to any port on the big switch or is there an uplink port on the big switch it should go to? then you would hook a cat5e from one of the regular ports on the 24 port switch and run it to the uplink port on the 4 port switch need to no if the whole sequence is right. Hope someone can help, john will told me the cable would go from the big switch to the uplink on the small switch but I am wondering if I have it all right or not and wonderiing about from the router to the 24 port switch does the cable just go in a regular port in the big switch or if there is an uplink port does it go there. Hope you can understand my rambleing here. Thanks (please don't send me to a link) just need to no modem to router to regular port or uplink port on 24 port switch then from regular port on 24 port switch to uplink port on the 4 port switch. Thanks
 

A:Solved: Windows xp hookup question for modem, router, switch, to switch?

Router to uplink port on 24 port switch, and then normal port on the 24 port switch to uplink port on the second 4 port switch. An auto-MDX port on a device negates the need to worry about uplink ports for that particular cable connection.
 

3 more replies
Answer Match 39.48%

I have Windows 7 Professional on my PC. In the first load I had, the PC should automatically detect if the LAN cable was plugged in, turn off the wireless radio, and change the network icon in the right bottom corner to reflect the cable was now in use.
Unfortunately, I had to reload my PC, and since then I can't get it to do it again.
So, what I'd like to achieve is this: Have Windows automatically detect when the cable is plugged in, turn of the wireless radio, and change the network icon in the right bottom corner to reflect the cable is in use - and, obviously, vice versa.
Can someone tell me what I need to do, please?

A:Have Windows 7 automatically switch to LAN when cable is plugged in and switch to wireless when it's removed

Hi,
There are two methods can help you.
1. Go to <Network and Sharing><Change Adapter Settings> and right click your wired and wireless adapters one at a time to change the properties. Select IPv4, click <Properties>
then click <Advanced>. For each one, clear the "Automatic metric" check box and assign the metric value manually. Setting your wired adapter?s metric value lower than wireless adapter one, such as ?1? for wired adapter and ?2? for wired adapter.

2. Go to <Network and Sharing><Change Adapter Settings>,
hold down 'alt' to bring up the "File" menu, select "Advanced", select
"Advanced Settings" from the dropdown menu, adjust the priority of your wired adapter higher than your wireless adapter in the "Advanced Settings" window under the "Adapters and Bindings" tab.
Hope this helps.Please remember to click ?Mark as Answer? on the post that helps you, and to click ?Unmark as Answer? if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread.

3 more replies
Answer Match 39.48%

Am a new Networking BEE I had built a small network of 20 systems at my office and there I had connected a switch and router.

All the switch ports have been covered by all the systems and one port is given to the router
switch(20)----router(LAN)
|
|
|
HUB(8ports)

And also I connected a HUB to the switch ..

It works fine for my internet connections to all the systems but how do i make authentication of passwords and username to my network systems from one server which I use server 2003 at one system

let me know the detailed step by step procedure to build.........

I would feel very happy If at all any Suggestions for me to make my Business grow.....

As early as possible ................

Thanks in Advance

Smiles....[][]
 

A:Connection of Router to Switch and also a Hub to Switch - N/W systems internet share

>>I use server 2003 at one system

you need to enable Network Login, but that requires that win2003 have

a domain controller
a DHCP service
and a DNS service.
the Domain Controller is just another name for LDAP and it becomes the control point
for all systems.

get some books on Configuring Win2003 Server
 

4 more replies
Answer Match 39.06%

One question I need to know

If you go from DSL modem to Router then Router to switch
my question is then
If I wanted to hook another mini linksys switch into the bigger switch would you run the cat5e cable from the first switch to a reg port in the second switch or would you run it to the uplink port and then hook the 1 or 2 computers into the reg ports of the second switch.??
 

A:Solved: Windows xp-question of hookup switch to switch?

Obviously, run it to the uplink port if available.
 

3 more replies
Answer Match 39.06%

hi all,

system gets hang, pc configuration is intel 865bgf motherboard with PIV 3ghz ht processor with 80 gb samsung hdd and 266 mb ddr i reinstalled the operating system (xp pro) changed smps and changed 256 ddr but the problem still continues, when the system gets hang i am not able to use my keyboard or mouse i have to restart the system , please help me and also i have to know weather is this the hardware issue or the software issue, and also i am facing same problem with same configuration with the other customer pc .
warm regards,
pradeep
 

A:system gets hang (it freezes) only option is to switch off and switch on

12 more replies
Answer Match 39.06%

Hi everyone, I searched through the forums but couldn't really find what I was looking for.

Currently we have a DHCP server set up to a switch, that has a special line connecting to a switch in our shop which is just across our back lot, giving network access to the few computers over there. They recently put in a new machine that needs network access, but they have already accidentally cut two ethernet cords. I'm looking to provide a wireless solution for the machine, but I don't want to have to spend a few thousand dollars on a large wireless switch.

Can I plug a wireless router into the switch in our shop, and essentially turn it into a wireless bridge, or is there another, simpler way to do this?

If this has already been answered, sorry for missing it!

Thanks!
 

A:Solved: DHCP Server -> Switch -> Switch -> Wireless

While you could use a router, or even configure the router to act as an access point, why not just buy a true access point? They start at $27: http://www.newegg.com/Store/SubCate...ame=Wireless-AP-Bridges-Repeaters&Order=PRICE
 

2 more replies
Answer Match 39.06%

Is it possible to switch off a laptop screen - laptop runs Windows 7 - and prevent it being switched on again, without inputting a password?

I need to keep the laptop running, therefore I can't put it to sleep and logging-off has become a pain.

I've tried the Power Options, but the display comes on again when the mouse is nudged.

I've also tried "Fn + F6" on my Acer laptop, which switches off the screen, but an accidental key press brings it to life again.

Any ingenious little prog around? None I've seen have that crucial password privacy aspect.

A:How to switch off laptop screen & password protect switch on again?

a password is is used when you are out but if you are home you don't need a password.. unless you don't trust somebody...

3 more replies
Answer Match 38.22%

Hello,

I use windows 7.
When I turn on laptop (acer Aspire 5742) cannot connect to internet until I switch user and log in again. Soon as I touch any browser icon the rest of computer stops responding as well. It's only me on computer. Have virgin media security/ spyware/ virus protection. Tried CCleaner. After I switch user everything is fine.
Additional info; On 16th October had great difficulty getting my emails from Yahoo. Sometimes sign-in box appeared without my security signature and different style of writing for browser remembered log-on details.

Cheers,

Gordon.
 

A:Solved: have to switch user to continue after switch on

11 more replies
Answer Match 38.22%

I thought that I had this all figured out, but my dad just asked me a question about my setup, and I can't answer it.

The setup is like this:
[ip-phones + computers]-->[small switch]-->[managed L2 switch]-->[router]-->[modem]

I have several ip-phones and computers grouped into blocks of 8. Each set of 8 is a medley of phones/computers connected to a small switch http://www.linksys.com/servlet/Sate...nksys/Common/VisitorWrapper&lid=3681322279B34

Each of these switches, in turn, will be connected to a managed L2 switch http://www1.ca.dell.com/content/products/productdetails.aspx/pwcnt_3448p?c=ca&cs=calca1&l=en&s=biz that will create 2 VLANS: One VLAN will contain all of the phones, and the other will contain all of the computers. In turn, each VLAN will have its own router and DSL modem, thereby separating the network traffic.

I know that I can use this L2 switch to make the VLANS based on the MAC addresses of the devices. However, the smaller switches do not support 802.1q [VLANs]. Will it be a problem that the smaller switches do not support VLANs? Essentially, will this setup work to split up network traffic?

Thanks once again,
-Roger
 

A:Computer, switch, switch, router, modem

I have the same DELL switch for my phones. You PoE will not carry across the linksys switches, so that is the first problem.
Next are the computers attached to the phones? Or does each device get its own drop?

And whats this about 2 routers and modems? Thats a bit over kill!! QoS would do the trick.

I would run all the devices off the Dell and attach the computers to the Phones (most IP Phones have a passthrough port) Configure the Dell with trunk ports with the Computer VLAN passing untagged traffic making it the native VLAN. While having the phones on a Tagged VLAN(If you phones conig allows you to set the VLAN in its config great! If not you can bind the MAC to the VLAN). The you create a QoS policy giving the VoIP traffic priority!
 

3 more replies
Answer Match 38.22%

Hi Everyone.....
So, I just got Wireless Broadband hooked up in my business. I hooked the LAN to the Router and then hooked up a 16 port gigabit switch. I have three terminals coming out of it (in the bcak of the building) as well as a line running to the front of the building. At the front of the building I have the line going into another 16 port gigabit switch. I have 4 computer terminals coming out of that switch. I AM getting internet at the back of the building .....but nothing at any of the terminals after the second switch (front of the building). Can someone help?

Thanks!
 

A:Router to Switch to Switch.....No Internet at end terminals

7 more replies
Answer Match 38.22%

Can any one advised me

I want to implement network on 6 Floor , 12-12 Port on each portion in one floor, total 24 ports on each floor keeping in mind distance between the each floors how do i connect them with fiber cable (which fiber cable i required) so speed remain constant for all floors.

How is my Idea to implement...right from server room in 1 floor where all internet connection providing to each floor. Cascading from 1 to 2 , 2 to 3, 3 to 4, 4 to 5, 5 to 6. UPon this setup...do i get into a low speed bandwith comparing to 1 floor Network. Does Network Gets slow by connecting through Cat5 UTP cable in cascading example.

Please adviced me.

-Thank Q>
Shiraz
 

A:How Can i Connect Gigabyte Switch to Gitabyte Switch

15 more replies
Answer Match 38.22%

i have this sr224 switch and i like to connect it to my giga network sr2024 switch.
now, i plug a utp belden cat5e to port 1 of sr224 and the other end to port 1 of sr2024.
what i got is the whole panel lights of sr224 will blink very fast.
is this normal? or sr224 and sr2024 cannot be paired?

thanks in advance guys
 

More replies
Answer Match 38.22%

Hi, guys. I have connected Huawei switch S5700-24TP-SI-AC with Cisco switch 2960 using one single fiber with LX SFP. The port is up on one side (Blinking on Huawei side) and down on Cisco side...Please help.
 

A:Huawei switch vs Cisco switch, How to connect

What kind of 2960 switch do you have? Have you checked the interface to verify the switch recognizes the optic and all the stats report back as normal? Are you using a Cisco branded optic? Do you see light being shot out from the optic in the 2960?
 

2 more replies
Answer Match 38.22%

recently i was having major computer issues on my desktop, i did a full restore to factory settings and after doing a few windows updates i found that my network adaptor was not finding any signals. it does not show up in the change adaptor settings page or in the device manager page. when i troubleshoot my internet connection it says an ethernet cable is not properly plugged in. I have a desktop computer but it definately has a wireless network card. i used to get windows updates for it and it just stopped working one day. when i look in the BIOS the only option related to booting a network card is B03 D00 Yukon PXE. no matter when i boot it i still dont get wireless signals. when i go into the boot menu and try to boot this device it says " PXE E61: media test failure please check cable" i have opened the tower and the card is securely in its slot. i thought i would workaround by getting a usb wifi card. I installed it and connected to the internet and it alternated between having a connection to the internet and being connected to the network but not the internet. even when it is connected to the internet i cannot reach any web pages. my dropbox desktop files update very slowly (7kb/s). when i am connected with the usb card the network stops working for everyone else in the house. they can no longer reach web pages or continue downloads. please help.

gateway DX4300
AMD Phenom II X4 810 processor 2.60 GHz
8.00 GB DDRII RAM
windows 7 home premium

EDIT: additional... Read more

A:wifi adaptor not recognized, usb wifi hogging wifi resources

13 more replies
Answer Match 37.38%

Hi,
this is my first thead, i do believe im posting in the right place,if it has been asked before, and i dont speak english much so ill try to be clear, so sorry

I would like to know if there is a way to switch the position of my DVD player and second hard drive without physicaly changing them? By that i mean, switching my DVD which is D: to my HD ( which is E: ) so DVD becomes E: and HD becomes D:?

Hope you can understand me

Thanks in advance
 

A:HD and DVD position

This depends on your cables and motherboard. The motherboard may only support 2 pieces of IDE hard ware, or it may support 4. If you have 2 single cables, this is not really possible. If you have 2 cables of which at least 1 is a double one this should be possible. Just open up your computer and swap the cables around. Maybe the cables are not long enough and you'll have to get an extender. Good luck. Hope this helps,

Regards,

Korrupt
 

2 more replies
Answer Match 37.38%

hey i got a very strange problem,
when in keep my CPU(tower) in vertical position my harddisk are not detected, well as when i lay it down i.e. in horizontal position it does detect my harddisk.
i have 2 harddisk 40gb(master)+10gb(slave).
 

A:CPU position

9 more replies
Answer Match 37.38%

IE11.09600.17842 (KB 305851)

I am running Windows 8.1 Pro 64 bit when I view the home page that In set up the url is at the top which is how I like it but if I type another web url to go to another web page the url shows at the top but if I send that to my desktop icon and close the IE11 and click on the Desktop icon that I have create the url is at the bottom of the page.

How can I set IE11 by clicking on the icon appear at the top of the page?

A:IE 11 url position

Are you switching between Metro and Desktop to type the URLs ?

5 more replies
Answer Match 37.38%

Those in red text are the fans that are already in my casing CM 690 II Advanced

Those in blue text are the 120mm fans I intend to add for air intake into casing. I intend to add either 1 or 2 fans.

1) Is adding a 120mm fan to A or B better?
2) Is adding two 120mm fans to A and C better? or A and B better?

Other suggestions are welcomed.
 

A:Which fan position is better?

More fans in any position does not mean better cooling. Too many fans can actually cause more turbulence decreasing cooling. The fans you already have should provide the proper cooling. Additional help cooling would be Cable Management. Keeping cables Properly routed and unused cables tucked away out of the airflow path.
 

2 more replies
Answer Match 36.96%

I understand that a hub is more like a party line, where all devices hear and read data before sending it to next port, and a switch is advanced hub. But, what is a router. I know what a wireless router is, but they say a router is more advanced than a switch. Can you buy a non-wireless router?

Also, can you connect 2 switches together? So, Modem-----to Switch----to Switch----Computer

And both switches have other devices connected?

A:Hub vs Switch vs Router/ 2 Switch Story

you CAN buy a non-wireless router--but--the two I found on Amazon were only 10/100 (most modern systems use gigabit ethernet 10/100/1000) but wired are generally cheaper than a wireless router(the Cisco below is NOT cheap)--however--it's not necessary to use the wireless part of the wireless router as most have at least 4 ports (wired).

Yes you can connect switches together but they won't allow for multiple computers to connect to the Internet (at least not easily nor in a way that makes sense).

What devices are you trying to connect together?

wired routers:
Amazon.com: TRENDnet 4-Port Broadband Router TW100-S4W1CA (Black): Electronics

Amazon.com: Cisco-Linksys EtherFast Cable/DSL Router with 4-Port 10/100 Switch: Electronics

4 more replies
Answer Match 36.96%

hi

im connectiong a switch to a switch, what connection do i use straight or cross.


thanks
 

A:switch to switch straight or cross

standard rj45 cables
 

5 more replies
Answer Match 36.96%

Hello all

I just installed 4GB ram on my 32 vista and it only recognized 3GB in the os (vista 32) and all 4GB in the bios. so I decided to use the /3GB Switch, by using that command in bcdedit, it all worked good. The problem is now I have 3069 mb physical memory and ONLY 209 mb Kernal Memory!!! so I used the "bcdedit /deletevalue IncreaseUserVa" and bcedit said it worked successfuly so i restart my pc and it STILL had the same memory! so right now im stuck with only 209 mb Kernal memory! any ideas on how to fix this? I looked all over google and found nothing. Should I keep these settings or try and fix it?how do i fix it?
 

A:3GB switch will not switch back, vista 32!

I am not too familiar with those commands you speak of, but I do have a question: Is the video card built into the motherboard? If so, what amount of system memory is being shared with it? Besides that, I have no more ideas to offer you. Sorry
 

3 more replies
Answer Match 36.96%

Hi, i have a AIO B50-30 and I'm trying to connect via the hdmi input socket my TV satellite box. I have found out recently that there is a switch on the side of the unit that will allow you to switch to the input channels so allowing viewing of the box and other like units Xbox etc. My issue is that I'm pressing the switch but nothing is happening it's simply staying on my desktop on Windows 10. Can anyone please help to see if I'm doing this right or am I missing something ?.  Any help, suggestions would be gratefully received since there is very little on the subject in connection with this particular model .thanks in advance.

More replies
Answer Match 36.96%

We are moving to a new office location. The guys who will be setting our network is proposing the following equipment:

1. 3Com 24-port 10/100 mbps switch
2. 24-port Patch panel
3. 6u data cabinet
4. 1u cable management

The new office will be a 2-floor building with around 40 computers. I asked some of my friends who are more expert on network setup and told me typical switch (Linksys, Cisco) will do if we need to save some money.

What do you think? Thanks a lot!
 

A:Is 3Com 24-switch necessary or typical switch will do?

Well, first off, I'd be specifying a gigabit switch for expandability, I can't see investing in a 10/100 switch in 2010! If you don't need a managed switch, or need to save money initially, and unmanaged switch will probably be significantly cheaper.

In point of fact, if you want to go really cheap, you can get away for less than $100!

http://www.newegg.com/Product/Produ...igabit switch&bop=And&Order=PRICE&PageSize=20
 

3 more replies
Answer Match 36.96%

I am really impressed with IE8 and made it my default browser, its fast, stable and look good. Congratulations microsoft and well done.

More replies
Answer Match 36.96%

Hi All,

Can any one tell me what is the registry key that control's the position of taskbar on the screen in Win7

A:Taskbar Position

Hello Gopal, and welcome to Seven Forums.

You can also change the taskbar position from the Taskbar Properties page.

Taskbar - Move Location on Desktop Screen

Hope this helps,
Shawn

8 more replies
Answer Match 36.96%

hello i was wondering if there was a property with the same effect
thats supported by NS too
 

A:css:background-position

6 more replies
Answer Match 36.96%

Hello... Has any Hard Disk Drive manufacture stated which position is best when mounting a HDD? I was thinking of mounting a couple new Seagates on "Edge." Thats having the 4 mounting 6-32 screws in a vertical plane. Another way of saying it would be: One inch wide, 3.5 inch high and 5 inches deep when looking at it in a very small tower case. Thanks.. agpilot
 

A:HDD, Mounting position?

Hey,

Hard drives will work just as effectively upside down as it will normal-way up.

Edit: To be quite honest, it's hard to understand what exactly it is you are asking.

Nick.
 

3 more replies
Answer Match 36.96%

Has anyone experienced problems placing the Master drive at end of cable verses center connector and slave to center? I am aware old IDE UDMA specs refer to Master on center and Slave to end but I have heard the newer controllers are not as fussy.

Any thoughts on this or problems found.

Dave
 

A:IDE Connection position

6 more replies
Answer Match 36.96%

Hi,
While cleaning, jumper on motherboard was mistakenly removed. I am not sure on which 2 pins it was placed.
Its Allinone desktop pc of hp. Model Hp Omni Allinone 120-1111in

Kindly guide.

More replies
Answer Match 36.96%

Can any one please help a to link, nay not as much as link just a nod or a word will do I cannot resize and remember screens in both AOL or Firefox if I resize and move the window it will fly 15mm/ 1/2" left or right and the same top to bottom ie:has to be left or right or small enough to fit in the middle of the screen on re start it's back to either full screen or a six inch box I have reinstalled the software for both about five or six times now and going menta

Colin
 

A:Size and position

In IE, after you resize the window, hold the Ctrl key when you close the window.
In Firefox> Tools> Options> Content tab> click the Advanced button beside JavaScript
settings, and make sure that Move or resize existing windows is checked.
You didn't say, but if using Windows XP.
Go to kellys-korner and scroll down to line #30
Windows XP Doesn't Save User Settings
Instructions to run regedits at top of web page.
 

1 more replies
Answer Match 36.96%

ok, this doesn't seem to happen to anyone else but when my orb's taller than the height of the taskbar it doesn't sit on the base of the task bar anymore, instead, part of the orb is cut off like in the screencap (the tiny one).

can anyone mind telling me how to get the orb to sit on the taskbar properly, with the top of it above the taskbar? sorry, i can't really explain it properly.

btw, i used Windows 7 Start Button Changer v 2.6 to change my orb

A:start orb position

How to Create Custom Start Orb Image

Maybe this will shed a little light. imo

9 more replies
Answer Match 36.96%

So I'm not sure what genius at Microsoft thought hey let's remove programs name it all apps and put it underneath the power button. Cause you know in terms of what people are going to be clicking on the power button would be far more common that any program them might use Pretty much none of those things above I use other than file explorer, I don't even put documents in my documents and I don't think I ever have. Is there a way to rearrange these? I haven't figured it out yet.
 

More replies
Answer Match 36.96%

Can someone please tell me how to make a popup window appear where we want it on screen. When I want to read my mail the window always appear in the center bottom of the screen. I want it to appear on the upper left of the screen instead.

The other anoying thing on the net is the size of the windows. Why the hell the size is always changing. When I open a damn page, I want it full screen, not small in a corner.

Thanks
 

A:Popup position

With regard to your popup, next time you open it, drag the window to the part of the screen you wish it to appear, close the widow, and see if it opens there the next time.

With the "sizing" problem, one a widow opens, put your mouse cursor on either side of the window and drag it open to full screen, then close the widow. It should 'remember' next time. The problem comes in sometimes when a popup is the last 'opened' window and that size is what's remembered.
 

3 more replies
Answer Match 36.96%

hi friends

how can I add a new toolbar and add it on Top, or, at left, or,
at right position of my desktop

thanks very much
Carlos

A:New toolbar at top position

Hello Carlos, welcome to Seven Forums!


Right click the taskbar and select New Toolbar.

8 more replies
Answer Match 36.96%

Heres the deal: I have a second LCD that I have my desktop extended onto and I would like to put icons on it but when I do and shutdown my computer, the next time i startup the icons have moved back to the first monitor. I would like to have freedom to put my icons anywhere I want to on the second lcd. Any suggestions?

Is this normal?

A:Icon position on second LCD?

It's not normal, I'm on a dual screen setup too, and I do have some icons on the second screen when I start the computer every morning. I'm thinking either Windows only detecting the second screen a little bit later that it should, or something else, I'm going to look around to see if I can find something, but feel free to post more if you want to.

4 more replies
Answer Match 36.96%

"Anyone know how to fix this issue? Running windows 7..Whenever I right click on a link to open in another window...the window opens at the bottom of the page...how can i configure it to open in the middle? "

A:how to fix position of window

What program are you using when you open a new window?

I use Firefox and just tried Rt click / Open new window.
It opened a new window in the "Last saved position" for FF.

I normally open links by clicking the scroll wheel so they open in a new tab (for me).

9 more replies
Answer Match 36.54%

Hi, how can I change the start button position at 'xp an '98. I want it in the middle between those two quicklaunch buttons/icons.

||

BT

A:'xp and '98 start button position

Hello and Welcome to TSF

How to Move the Taskbar from Its Default Position

2 more replies
Answer Match 36.54%

When I hover over a question/reply number (in this forum), I see the link in the status bar and can use it to insert a link that would open the page in that position.
Example

How do I do that in other pages?
Example2
Example3

In those pages, I can't find any link hovering with the mouse over a specific section.

Thank you.

A:Link to a certain position in page

It appears to be based upon the number after the /, for example, changing the link to this page /350332-link-certain-position-page.html to /350311-link-certain-position-page.html takes you to a different thread/post on this forum and changes the text after the /350311 to show the new page. It must be associated to how the sites are created and pages written.

5 more replies
Answer Match 36.54%

We are using Windows XP on a MDG desktop with Samsung monitor. My daughter had started up Windows this am and was just starting to write a report in MS Word 2003 when the screen went black and then ~30sec later, the display went to horizonal. I have tried to reinstall the monitor drivers but it remains horizontal.
 

A:Screen position is horizontal

have you tried ctrl+alt+arrow key
works at my school.
 

2 more replies
Answer Match 36.54%

Is there a way to do this using Windows XP, without relying on some 3rd party utility? Currently, I want to move my icons where I want them on the desktop. (I uncheck auto-arrange and align to grid). Then, after rebooting, however, the icons all go back to the left hand side.

I found iconsaver (www.iconsaver.com) which allows me to restore the position of my icons when I reboot... but I'm just curious if there is an automatic way to do this without using this software.

Thanks.
 

A:Saving Icon Position

Hi .. I have my icons where I want them and I have a check mark on the following >> align to grid and show desktop icons . And they stay that way even after a reboot , So give that a try
 

2 more replies