Tech Problem Aggregator

Memory module/processor?

Q: Memory module/processor?

Helloes mates, ive got the following problem thats been annoying me for the last couple days.

I just bought brand new computer parts and im trying to get them to work together.
Ive gotten to a point where motherboard displays an error "C1" continuously(this motherboard has a small led display that shows error messages). Even tried resettin CMOS, changing places of memory modules, only using one module etc. but i still can't get it to work.
Also the memory modules seem to generate alot of heat during that time that motherboard is stuck at C1 phase. I haven't had the balls to keep it going for more than 5 minutes since at that point memory modules heat build-up seems to be too much.

Motherboards manual says for C1 code that:
Detect memory
-Auto-detection of DRAM size, type and EEC
-Auto-detection of L2 cache (socket 7 or below)
System:
Motherboard: Abit AB9 Pro Intel 965 LGA775 ATX
CPU: Intel Core 2 Duo E6600, 2,40Ghz, Socket 775, FSB 1066, 4MB Cache
Power: Nexus NX-4090 400W ATX
Video card: Club 3D 8600GT 512MB GDDR3 PCI-E DUAL-DVI TV
Memory: Corsair Twin2X 2x1GB DDR2 800Mhz kit

A: Memory module/processor?

POST error C1 indicates RAM refresh has failed.

Try the RAM in another bank or try a diff module. Check to make sure the banks are clear and free of obstructions.

2 more replies
Answer Match 52.5%

what is the difference in ecc and non ecc memory sticks and does it make a difference which one you can use in a dell optiplex 200. also does it make a difference if it is 40ns or 45ns? currently i have just 256mb and want to upgrage to 512mb. so i guess i need to know what is the correct sticks to buy that work with my dell. the stick in it now is 40ns.
 

A:memory module

Most desktop don't use ECC (Error Correction Code) Memory. However, this is a link to Dell with what they have available for sale for an Optiplex GX 200 if that's what you have. It is ECC memory. I looked at crucial.com, usually a good site to do a memory search and they didn't have anything listed, but suggested you might need "proprietary" memory.

Optiplex GX200
 

1 more replies
Answer Match 52.5%

Hi, i was just checking out a site that sells memory upgrades... http://www.comptick.com/cq-m266-1gb.html

I noticed that theyre selling 1 GB laptop memory for hp (it doesnt mention two 512mb sticks).
Im using a compaq m2000 laptop, is it possible to just buy a single 1GB memory stick to place into one slot or would i have to buy 2 x512mb? how many bytes can each slot hold?

thankz
 

A:1GB memory module?

The max ram for that model laptop is 1GB so the safest most reliable way to go would be to purchase 2x 512MB. read this page from 4allmemory.com
Good website for memory, I use it all the time.
 

3 more replies
Answer Match 52.5%

I have this laptop thats a bit old, I know it has a Pentium3 and 128mb ram. What I am trying to find out is the size,module of the ram? like if its PC100? or PC133? are there any programs out there that do this trick? thanks
 

A:memory module?

Make and model of the laptop would be useful. You can also go on sites like Kingston ,use their configurator and you will find exactly the memory you need.
 

2 more replies
Answer Match 52.5%

Hi Tech Guy,
Can you email me web URL's to buy a 1 GB Memory Module for a Dell OptiPlex GX270 with a Processor x86 Family 15 Model 2 Stepping 9 Genuiielntel ~2992 Mhz so I can upgrade my PC & OS ASAP
 

A:Where can i buy a 1GB Memory Module for my PC?

10 more replies
Answer Match 52.5%

My owners manual for Dell 2400 series desktop calls for a PC2700(333-MHz)DDR SDRAM (non-ECC) Memory Module

Will a Kingston 512MB PC2700DDR (KVR333/512R, KVR33350/512R) Memory Module be OK?

I'm confused can some one help?
 

A:Memory Module

13 more replies
Answer Match 52.5%

I have an NEC memory module with the following markings on each of the two chips:4318160-70 and 9451AU600. the back of the board has the markings: P7460 and P10-04B74600.

Can someone please advise me as to the capacity of the module and whether or not it is parity.
 

More replies
Answer Match 52.5%

By looking at a stick of memory how can you tell how much RAM it is please?

TIA
 

A:memory module

There should be a sticker on the module giving the specifications.
 

1 more replies
Answer Match 52.5%

Dear Sirs,
I recently put together a system that consists of:

Motherboard - Soyo K7VTA VIA KT133 chipset 200 FSB
CPU - AMD Athlon Thunderbird 900 Mhz
Memory - 1 Micron 256 MB, PC133
Hard Drive - IBM 40 GB ATA 66 7200 RPM
OS - Windows 2000 SP 2
Video - Gigabyte Geoforce2 MX400 64MB

This system has been running fine and without incident until I recently purchased an addition memory module. The memory module is identified on the chips as, Siemens HYB39S256400T-8(B). It was advertised as 512 MB Unregistered, PC133. I installed the memory into the next available DIMM socket (3 onboard). When I rebooted the computer several things happened.

1.) The PC booted through BIOS where the memory was tested and recognized (786,432 total memory) them memory and began to load Windows and then suddenly rebooted. This occured over and over.
2.) After booting into BIOS setup (Memory was recognized in BIOS) I exited and when the machine rebooted I received a STOP error.
STOP error = The ACPI BIOS in this system is not fully compliant with the ACPI specification. 0x000000A5, 0X00000011, 0X00000007, 0XEB8680C0, 0X0100000C

I then removed the new memory module and the machine booted normally.

Can you please offer me some suggestions.

Thank You,
Kelly Rudnick
[email protected]
 

A:Memory Module from .........

What happens if you put just the new module in? Any problems (could be a bad module)? If not:
Do you know if the new memory is ECC or non-ECC? What about the original memory?
Also, do you know if the original memory is also unregistered/unbuffered as opposed to registered/buffered?
If they are of different types, they may not play well together.
 

2 more replies
Answer Match 52.08%

When I checked my computer screen this morning it was stuck on Reset 2%. After shutting down, my system will not start, just displays hp with very slow blink. I was able to run a system check and received a failure ID: RGFX3F-78387E-QFFV61-402G03. MEMORY MODULE FAILURE. Oh, what to do, can anyone help?

More replies
Answer Match 52.08%

Sorry I am dim, but I can't figure out if the memory I have will work with the mobo i have.

mobo: Asus A7V400-MX
(from the supoprt manual: supports up to 2GB unbuffered PC2700/PC2100/PC1600 non-ECC DDR SDRAM)

Memory: 1 x 512 DDR 400 PC3200 UDIMM made by elixir.

I know the 'PC' numbers don't match, but i was assured twice by the tech guy that the memory is backwards-compatible with the mobo specs.

Unfortunately I am having problems with the new mobo, which may be due to the new memory, I'm not sure!!

The full problem I'll describe if I get past this issue. Don't want to bore you with it all stright up at first.

Ben
 

A:Does this memory module fit this mobo?

Yes it should work. It will just run at most 2700 (333MHz) or slower
instead of 3200 (400MHz), depending on the CPU FSB and your settings.
 

6 more replies
Answer Match 52.08%

I went to the Gateway site and found they recommend the following memory upgrade.

Infineon 512 MB PC2-4200 533 MHz Dual-Channel DDR2 SDRAM

When I place this in the search engine for Newegg, it comes up with nothing. I want to add 1 GB of memory. My computer is a Gateway GT5220.

According to the site I have 4 memory slots, 2 free (512+512+0+0)

With the information above, can you tell me what I need to look for online to order the correct memory for my computer?
Thanks
Peg
 

A:Solved: What memory module do I need

Here you go http://www.newegg.com/Product/Produ...080+1052408147+1052308476&name=1GB+(2+x+512MB)

Kingston, Corsair and Crucial are all good brands.
 

2 more replies
Answer Match 52.08%

my laptop is not starting and caplock key is blinking 3times between a pause it means it has a memory failure. I'm using original memory, tell me how to reseat my device.

More replies
Answer Match 52.08%

memory module not functional led blinks three times tried other rams still not bootingwifi f12 button blinks simultenuoslyhow to repair

More replies
Answer Match 52.08%

Memory Test FailedFaiure ID: 90931T 64P84A QFPK1G 407K03Product ID: A5F74AV Memory Module Hi, I am trying to figure out what is wrong with my laptop and see what I need to fiix or replace. When you try and boot it, it goes in circles trying to do the "Preparing Automatc Repair" but it always fails and says the PC did not start correctly. Upon hitting restart the process repeats. Ocassionally ading the step of diagnosing PC but nothing else happens.  I am unable to get passed the booting process. Any help or advice would be great!

A:A5F74AV Memory Module

You have a dv6t-7000 model and you have a bad memory module. This is a little fuzzy but watchable. See at 2:50 into the video how there are 2 modules. Try each module by itself in each slot and see if you can boot the machine and also run the test. That should isolate the bad memory module and all you would need to do is replace it. Will also diagnose if a slot is bad if modules work in one slot but neither works in the other slot.  Post back your fuindings and we can go from there.  https://www.youtube.com/watch?v=Xnw3lnSMXEg

1 more replies
Answer Match 52.08%

Hi Guys,
Thought i'de upgrade my 2 half gig ddr 266 memory sticks, too
2 one gig ddr 266 memory sticks.
when i installed the sticks the system soon started rapid bleeping, and the moniter display the no video input message. I reinstalled the old memory, back to normal. Any ideas would be appreciated.
All the best.
Cos.
:chef:
 

A:Memory Module Issues

What is the make and model of the new memory?
 

19 more replies
Answer Match 52.08%

Hi I have recently purchased inspiron 5567 laptop and I think I would need to add more RAM to it.
in India I don't find anywhere on the Dell official site, an option to purchase a memory module.
So I wanted to know from where I can purchase a compatible RAM for Inspiron 5567? (do I have to look for any specific brand for memory module?)
Is it okay to purchase from a local computer store or from online store like Amazon or Flipkart?
Secondly, do I have to take my laptop to the service center to replace the module or I can replace it at my home itself?
If I replace it at my own, will it affect my laptop's warranty?

A:Upgrading Memory Module

It'll take up to 2X8G DDR4-19200 modules; yes, you can purchase the memory and install it yourself (simply requires removing the base cover).
Disconnect the battery and unplug the system before upgrading.

1 more replies
Answer Match 52.08%

i just installed a Kingston 64MB PC100 in the next slot to the one already holding a 64MB PC100...... restarted...... no monitor..... black....... took the emodule out again... rebooted....... everything back to normal.... what is going on? Did I miss something? What else do you have to do besides insert the memory into the slot and make sure it's seated and the claps are closed? The Ram is new.
 

A:New Memory Module = Problems

11 more replies
Answer Match 52.08%

I have read some data that says that Windows Seven has problems with mixed sizes of memory modules. In my system I have three 2 Gig modules and one 1 Gig module. Can this cause any problems. The memory came preinstalled in my system so I assume it is of same type and manufacturer. Still trying to chase a problem with desktop heap allocation failure at boot up.

A:Memory module size

  
Quote: Originally Posted by arliedog


I have read some data that says that Windows Seven has problems with mixed sizes of memory modules. In my system I have three 2 Gig modules and one 1 Gig module. Can this cause any problems. The memory came preinstalled in my system so I assume it is of same type and manufacturer. Still trying to chase a problem with desktop heap allocation failure at boot up.


The size of the module shouldn't matter as long as they are exactly the same specs. If you think the heap problem is caused by memory download and run memtestx86 for several hours at least.

You can also check in event viewer (type event vwr in search) for log entries. Go to windows logs>application tab (and system)and look for errors (red in the left hand colum) relating to the problem. When found note the event ID and source codes and relay them to us

Let us know if you need help

Ken J+

3 more replies
Answer Match 52.08%

I'm currently running my system on a puny (it seems) 512 MB of DDR SDRAM (2 sticks of 256).
However, I've just bought 1GB PC3200 DDR SDRAM 1 stick 400mhz to upgrade it & have heard a horror story from a friend that this won't work as I need to buy 2 matching sticks of the same memory for it to work.
Is this true?
 

A:Memory module query

9 more replies
Answer Match 52.08%

hi everyone wondering if anyone can help me please,i have ran malwarebytes and it has picked up two virus and says will delete on reboot but they wont go away it makes my computer bleep now and again and its definitely not running right,slow and keeps messing internet pages and desktop icons in toolbar area not present as to what they were before so on... well i dont want anything thats not supposed to be in there you know what i mean i ran avg and that has picked them up but still when i run malware it still finds the same two trojans and in the log file this is what it says...\\?\globalroot\systemroot\system32\hjgruixjetaspb.dll (Trojan.TDSS) -> Delete on reboot. the second one is....\\?\globalroot\systemroot\system32\hjgruixjetaspb.dll (Trojan.TDSS) -> Quarantined and deleted successfully. but like i say avg has done full scan and then malware keeps finding them and theyre still there... anyone help please??

A:memory module virus

Hello and welcome to Bleeping Computer.Please subscribe to your topic so that you will be notified as soon as I post a reply, instead of you having to check the topic all of the time. This will allow you to get an email notification when I reply.To subscribe, go to your topic, and at the top right hand corner by your first post, click the Options button and then click Track this topic. The bullet the immediate notification bubble. Then press submit.I am sorry to be the bearer of bad news but: One or more of the identified infections is a backdoor trojan. This allows hackers to remotely control your computer, steal critical system information and download and execute files.I would counsel you to disconnect this PC from the Internet immediately. If you do any banking or other financial transactions on the PC or if it should contain any other sensitive information, please get to a known clean computer and change all passwords where applicable, and it would be wise to contact those same financial institutions to apprise them of your situation.Though the trojan has been identified and can be killed, because of it's backdoor functionality, your PC is very likely compromised and there is no way to be sure your computer can ever again be trusted. Many experts in the security community believe that once infected with this type of trojan, the best course of action would be a reformat and reinstall of the OS. Please read these for more information:How Do I Handle Possible Identity T... Read more

1 more replies
Answer Match 52.08%

Hello,
I am trying to reformat a friends computer. It is a real mess, so I do not want to clean it out. But when I try to run the xp-setup, it gives me a bsod with different messages, all including setupdd.sys. I can boot normally, setup loads files, I am asked what I want to do, press enter to setup, accept license agreement. When it asks me where I want to set up windwos, partitions etc, it show 4 unknown devices with unknown size, no harddisk, no partitions, after that, whatever I do, a bsod.
I googled this up and it seems to have to do with bad ram. My computer shows all disks and partitions without problems, so I figure it is not a hardware problem, but malware, preventing me from formatting/re-installing windows xp.
The problem is, that all works fine, ram test is fine. I ran several antimalware tools and mbam gave me one time (not the first scan) an infected memory module with a win32 trojan. It said delete on reboot, I rebooted and reran the scan and now it says the same. Sorry, I did not include the log, but I am afraid to use my usb-stick to copy the log, after what I was on that PC, I became a little paranoid.
Malwarebytes, run in normal mode, quick scan, reports memory module infecten with trojan downloader, c:\wiindows\system32\wmimgr32.dll and the file c:\windows\system32\wmimgr32.dll.
When I run the scan in safemode, it does not detect a thing.

I appreciate any help!!

A:Memory module infected

In time I also ran dr. Web, some 2000 infected files with win32.hllp.neshta and win32.sector.204800, file infectors, very nasty, but apparently cured. I ran windows memory test, no errors found. I ran also checkdisk, inclusive surface scan and it found some problems (as a result of file intection?). The problem still remains, I start windows setup, it still does not recognize any partitioned/unpartitioned space (I checked in my computer, 50 Gb partitioned and 100 Gb unpartitioned) and after any choice I make there (create, delete, setup) a bsod.

2 more replies
Answer Match 52.08%

Hey there,
I checked to c what memory would b suitable for my laptop ( HP Compaq nx6110 ), and it seems i need DDR PC2700..
I was wondering if it matters if i use PC2700,2100 or some other ...
Does anyone know if my system would function with any of the other PC speeds?

Greetz,

Pendejo
 

A:Memory Module question

Usually, faster speeds are OK (it will just run at the motherboard speed or the speed of any other RAM module also installed, whichever is the slower)

But if you install slower RAM (2100) then all RAM, including any original module that may be faster will run at the slower speed.

I have not experienced issues using faster RAM, but very rarely timing issues may arise and it will fail to work. But it's rare.
 

3 more replies
Answer Match 52.08%

Hello Windows Vista Forums,

I would like to upgrade my Random Access Memory (RAM). I am thinking to put 2GB RAM cards into my machine. I have a small problem though. I don't know what type of memory my I should put into my machine. I own a Alienware Area 51 7500. Here are the system specs:

System Manufacturer/Model Number Alienware
OS Vista Ultimate x64
CPU Area 51 7500
Motherboard MB-EVGA122CKNF68B1
Memory 8GB ElPIDA DDR2 PC2-6400 U-DIMM 800MHZ
Graphics Card(s) NVIDIA GeForce 8600 GTS
Sound Card EAX3
Monitor(s) Displays SAMSUNG 23" GAMERS CHOICE
Screen Resolution Primary 1680 X 1050, Secondary 1920 X 1080
Hard Drives ST3250410AS
Model: ST3250410AS
Size: 250GB
PSU CoolerMaster 1000
Case Alienware Black Head Chasis
Cooling Noctua NH-U12P x 1x120mm fan, 6x120mm case fans
Keyboard Alienware M51 Standard Keyboard
Mouse Alienware M5 Standard Size Mouse
Internet Speed 54.0 MBPS
Other Info Bought in October of 2007 from Alienware.

If anyone can reccomend a type of RAM for machine and where to purchase for a good reliable price, that would be fantastic! All help is appreciated! Thanks!

Regards,
alienware

A:RAM Memory Module Upgrade

Pretty sure you'll be good with 240 pin DDR2 modules. Best to install in pairs, so keep that in mind. While newegg isn't guaranteed to give you the best price, they've always been reliable wherever I am in the world when it comes to shipping.

Newegg.com - Computer Hardware,Memory,Desktop Memory,240-Pin DDR2 SDRAM

Those are the modules for your board sorted by rating. I personally have Mushkin brand in my tower, but I'm not partial to any brand. Check out the reviews. Maybe someone else here has the same mobo as you and can offer some first hand experience on what you should get. Good luck.

Also for future reference

http://www.crucial.com/

You can go there and find the proper ram size/timings and then use that info to do a search on newegg or your favorite shopping site.

According to them here's the ram you need (http://www.crucial.com/store/listpar...AREA-51%207500)

Package: 240-pin DIMM
Feature: DDR2 PC2-5300

7 more replies
Answer Match 51.66%

have CQ60-101AU laptop. I'd like to buy Corsair Memory ? 2GB DDR2 SODIMM Memory (VS2GSDS800D2). Is it compatible with my laptop?
 

A:CQ60 memory module (RAM) compatibility

http://www.crucial.com/upgrade/compatible-memory-for/HP+-+Compaq/Presario+CQ60-101AU/list.html
 

3 more replies
Answer Match 51.66%

Hello,
 
I have a Dell Studio 1737 laptop, Runs Vista. Bought in 2009.
 
A month or more ago, the battery stopped working. I haven’t replaced it yet, because, 1. It went from working to not working very abruptly, and I’m not sure that’s how batteries die. 2. Checking online, I read it might be my BIOS. 3. I know someone who replaced her battery and it only worked for a week or so. So her computer must have another issue going on, maybe mine does too.  
 
The last 2 weeks, the laptop has been freezing at random times.
 
When it’s not freezing, it’s running great. I run virus and malware checks often. Paid Avast, free Malwarebytes, ADWcleaner, CCleaner, and I ran Windows Repair All in One.
 
I ran a diagnostic test at Dell, it found a critical hardware failure--my memory module isn’t working properly and should be replaced. My System Info says that my -- RAM is 4.00 GB, Total physical memory - 3.96 GB, Available physical memory - 2.58, Total virtual memory - 8.12 GB, Available virtual memory - 6.62 GB.
 
Question-could this memory module issue cause the battery issue and/or the random freezing?
 
I also attempted to update my BIOS at Dell, which was a recommended update. It wouldn’t allow me to complete the update, because there was no battery.
 
 
Any advice would be welcome.
 
Thanks.
 
marber
 

A:Battery, BIOS or memory module?

Hello - Yes batteries can die abruptly.. normally you would see a decrease in how long it stays charged and then it would simply fail.  But it could be yours just decided to die.  Also your computer's freezing can be attributed to bad memory and if their memory tester found a problem you may indeed have failing memory, but I would try replacing the battery first ( just in case somehow the lack of battery is affecting the memory circuit. (unlikely but possible).

23 more replies
Answer Match 51.66%

Hello everyone: A few weeks ago I pushed the button to start my PC. It started with its usual routine but then stopped booting up and just started beeping at me. After several attempts at forcing it to shut down then starting it again only to have it beep at me I just left it off and used the laptop to do some research about the beeping. Seems it had to do with a memory problem which I managed to locate by removing the memory modules one at a time and replacing them in the same location they came from. I managed to isolate one module that when installed, caused the machine to beep and boot no further, and when removed, the machine booted up o.k. although it was a bit sluggish and acted like it wasn't to sure about what it was supposed to do with itself. It just so happened that it was in an end socket and when I removed a module from the opposite end and placed it in the suspect socket, the beeping started again, so I put that module back in it's place at the other end and left the other socket empty. I'm actually using the PC in question to make this post, it seems to run satisfactorily without the one module in place, but at times seems to loose its bearings. Sorry about running on, my question is. "Is the the memory module the problem, or is it the socket that the memory module plugs into the problem, and what is the solution either way? On this particular machine a H.P. a1250n Media Center desktop; I can install up to 4 1-gig modules, I'm using the 2 512 MB modules i... Read more

A:Memory Module or System Board?

Hello,

Since the beeping starts when using a known good module in the "suspect" slot it

would seem to indicate a problem with the slot.

You can try testing using one working module in all slots to make sure that the issue is the slot.

If the slot is determined to be defective the board would have to be replaced.

This can be an issue with OEM unless the board is replaced with the same board.

7 more replies
Answer Match 51.66%

Hello!

How to remove the memory module?

Get the following message and for me this means that one of the modules is broken:

Memory Error
Address = 00034000H
Read Date = 28034000H
Write Data = 00034000H

For my opinion the computer should boot again when I remove the broken memory slice?

Cheers Australia

A:Tecra R10 - How to remove memory module?

Hi

You can remove easily the memory modules.
I think the bay is placed at the bottom of the unit.
You have to remove the screw securing the bay and you will get a access to the module.

Here is a video how to do this on another notebook Satellite L500. But the procedure is not very different on Tecra R10
http://forums.computers.toshiba-europe.com/forums/ann.jspa?annID=81

Hope this helps a little bit

3 more replies
Answer Match 50.82%

I get this message whenever I log on; try to run regedit or msconfig. I'm frustrated trying to find out what the problem is...can you help???

Each time the @ # is different...i.e., ". . . in module kernel32 at 5443:91271892" these numbers change each login.

I can't see what is running on startup because this message occurs and never goes into msconfig.

HELP!!
 

A:Memory Access Violation in Module Kernel32 @ . . .

7 more replies
Answer Match 50.82%

Hello,
I have a Dell Dimension 4550 which currently has 512mb of RAM on board.
I want to add another 512 module.
The Owners Manual states that I should remove the AGP CARD before adding a new module. It doesn't say that I should replace it when the new memory is inserted.
Can anyone tell me what is the function of the AGP card and if it is necessary to remove it before adding the new memory module?
Thanks.
Cobh Rambler.
 

A:Is it necessary to remove AGP CARD before adding memory module?

There is no reason to remove an AGP card if you are adding more memory. Unless the AGP card physically blocks the RAM slot (not allowing you to put the RAM in), you need not worry about the AGP card.
 

2 more replies
Answer Match 50.82%

This is supposedly what happened to my computer. Is there some way to prevent this or find out early enough to prevent drive erasure?
 

A:Can bad memory module erase hard drive?

12 more replies
Answer Match 50.82%

Hello members, this is my first day as a member and i got a problem.
I have a ASROCK K7VT2 motherboard with a Athlon 2000 cpu and 256 mb of 266ddr ram, but i have decided to upgrade so i have lobbed the 256 mb of ram out and replaced it with a single stick of 1gb of 266 ddr ram.
Noweverything works and it is faster BUT its only showing as 512mb of ram, the BIOS is fully updated and i have tryed the ram in the second slot to no avail. Have looked in the manual and the board says it takes 2gb of ram and it has 2 slots so 1+1 = 2 YE only this board dont wanna play i have tryed emailing asrock but go no reply so HHHEEELLLPPP can anyone help me please

dave
 

A:Asrock K7VT2 memory module not recognized!!! HELP

this will definitely not solve your problem, but please read the contents of this link http://forums.techguy.org/t337978.html

it says how much asrock sux. sorry man.

by the way

Hello and Welcome to Techspot
 

5 more replies
Answer Match 50.82%

Hi,

I've just bought a Toshiba NB 510-10D and I can't find where do I have to change the RAM memory,

Can anyone help me?

Thanks!

A:Replace the memory RAM module of TOSHIBA NB510

Hi

I found very nice YouTube movie How to replace the RAM for Toshiba NB500, NB520, NB550D Series
http://www.youtube.com/watch?v=6mnQQbladnA

Check this.
The plastic cover at the bottom of the unit needs to be removed? there you will see the HDD and the memory modules. Spread out the two memory lock latches so that the memory module pops up. Pull the memory module up and out at an angle, using care to avoid touching the connectors. Remove the memory module.

That?s all.

2 more replies
Answer Match 50.82%

Hi. I done a report on my pc using EVEREST because I wanted to upgrade my RAM. It says:

[ Memory Controller ]

Memory Controller Properties:
Error Detection Method None
Error Correction None
Supported Memory Interleave 1-Way
Current Memory Interleave 4-Way
Supported Memory Speeds 70ns, 60ns
Supported Memory Types DIMM, SDRAM
Supported Memory Voltages 3.3V
Maximum Memory Module Size 256 MB
Memory Slots 2

It says maximum Memory Module Size 256MB. Does this mean I cannot put a 512MB memory module in or does it mean the most ive got in it is 256mb?
 

A:EVEREST - Maximum Memory Module Size

9 more replies
Answer Match 50.82%

I know you're not supposed to mix memory modules, but I have an extra 256 mg module that's a different brand from the modules now in my system. My mb (ASUS) manual says "For dual channel configuration the total size of memory modules installed per channel must be the same for better performance" which I have now w/the 2 512 mg modules installed (Patriot). It also says "Always install modules w/the same CAS latency".

My questions:

1) Could installing the 256 mg module actually weaken performance of the "dual channel configuration"?

2) If it is a different CAS latency, could it harm the mb or other memory modules in any way?

I figure if it doesn't work, the system just won't boot and I'll remove the extra module. But if it does boot, I want to be sure no harm is done to the mb, the other modules, and that it won't actually degrade the dual channel performance of the other 2 modules.

Thanks much,
Harold
 

A:Solved: Can This Memory Module Harm my System?

7 more replies
Answer Match 50.82%

Hello,
I've posted this already but I was wondering if there was anyone else had an opinion on this.
I have a Dell Dimension 4550 which currently has 512mb of RAM on board.
I want to add another 512 module.
The Owners Manual states that I should remove the AGP CARD before adding a new module. It doesn't say that I should replace it when the new memory is inserted.
Can anyone tell me what is the function of the AGP card and if it is necessary to remove it before adding the new memory module?
Thanks.
Cobh Rambler.
 

A:Is it necessary to remove AGP CARD before adding memory module?

The AGP card would be your video card, you'd definitely want to put that back in or your computer won't work. Normally you don't remove the video card to install more memory.

The only reason I see for doing that, since its not a normal procedure, is that the card may be in the way of the latches on the side of the memory slots.
 

2 more replies
Answer Match 50.4%

I have the small Inspiron 3250 Desktop.  Processor information:  Intel(R) Core(TM) i5-6400 CPU @ 2.70GHz (CPU:0).  Memory type:  DDR3 (1600 MHz).
I want to add another 8gb memory module.  I have asked Dell representative 5 times about which module to order.  I have received 4 different recommendations and one "your PC can't be upgraded).  I do know that my PC has two slots for memory and is only using 1 8gb module so I know it can be upgraded.  I just don't know which module is best suited for my PC.
Any suggestions??  Thanks in advance

A:Inspiron 3250 Small Desktop Memory Module

Have you called Dell Spare Parts directly (totally separate from Dell tech support) and given them that part number?
You can look at Crucial.com. They have 2x8GB RAM for this system model for ~$94. The good thing about Crucial is they guarantee it works in whichever system they recommended it for or they take it back. Many people around this forum buy from Crucial.
But do yourself a favor. Start at Crucial's home page and work through their product finder on the left side so you know you looking at RAM for your system. Don't just rely on the link I posted, because -after all- it is your money.  
You will have to click the "Show more" button when you get to the page for your model to see the 8 GB modules.
And I guess you could sell the Hynix module on eBay etc to recover some of the cost of a new pair...

3 more replies
Answer Match 50.4%

Please help.
Does anyone have a *photo or physical description* on the original 128 Meg module that went in the the 3440CT.

I know the part number and specification I'm specifically trying to identify if the one in my 3440CT is a Toshiba part and therefore under the 10year guarantee. Its faulty.

Paper Label Printed with:-

* square "3d" bar code
* 128MB PC-133
* MTGA83S-86KI3
* EAE
* S/N:S36000801096
* WARRANTY VOID IF LABEL REMOVED

The chips are KTI
TSV864T4I1A

it has 4 chips on each side and is a Micro Dimm 144 pin.
Printed on board is T3-0196 REV:1.0

I hope this link works. This is one on Ebay in Poland
http://i8.ebayimg.com/01/i/000/d1/ae/cd1e_1.JPG

Thanks
Neill

Message was edited by: neill.bird

A:Portege 3440CT: What is a orginal memory module spec

Hi

Portege 3440 supports 64Mb of internal memory and this memory cannot be removed.
So only one slot is available.

As far as I know Toshiba recommends using these modules for an upgrade:

*SDRAM 64MB (PA3033U-1M06)*
*SDRAM 128MB (PA3034U-1M12)*

I think you could google for these single numbers and you should get a photo or all needed details about these modules?


Bye

8 more replies
Answer Match 50.4%

Hi my name is Richard.I got a pc here and we got a major problem.   203 - Memory module failed self test and failing rank was disabled (slot 3) I know this a ram , motherboard problem but I don't know how to fix it. My devices does not work, it said LSI Raid error, my keyboard, mouse does not work. I tried to spam f10 for bios but It still showed up the error message. I dont wanna spend too much money on this. I really need to fix this problem before I ever get in trouble. I believe my ram comes with the motherboard because I don't see any ram sticks inside my pc. I tried to reboot but nope, it still gave me the message. This really scared me, I could not get any devices working, I could not go to bios, I dont have a clear disk to diagnose on. I've seen forums thesame as this but non of them worked. Please help us. I will try to be active as soon as possible.  Any replies will be replied and, Please help us and tell us the solution for this. I only saw HP users have this. I don't want to spend $500 bucks for a new pc.  Specs: PC: HP Workstation x8600DDR3 Memory: 6 gbPciE: Zotac Geforce GT 610  Any further replies will be replied as fast as possible. I will try to be active as soon as possible.   Thank you staff, volunteers and members for reading this thread. I've tried everything i could do to fix this, nothing seems to be working.                 &nbs... Read more

More replies
Answer Match 50.4%

I have a Dell Inspiron 5521 Laptop having 4 GB RAM. I am planning to add additional 8GB RAM.
So, the Total RAM would be 4+8= 12 GB.

I found the following information in Dell Specifications User Guide:

Memory
Connectors:
Inspiron 5521 Two internally-accessible DDR3 SODIMM connectors
Inspiron 5537 Two internally-accessible DDR3L SODIMM connectors
Capacity Up to 16 GB
Type:
Inspiron 5521 Dual channel DDR3
Inspiron 5537 Dual channel DDR3L
Speed Up to 1600 MHz
Configurations supported 2 GB, 4 GB, 6 GB, 8 GB, and 16 GB

I found the following Memory Module information by running Command on my Laptop: 
Total Width: 64 bits

Data Width: 64 bits

Size: 4096 MB

Form Factor: SODIMM

Set: None

Locator: JDIMM2

Bank Locator: Not Specified

Type: DDR3

Type Detail: Synchronous

Speed: 1600 MHz



Question 1: Is it possible to add 4+8= 12GB configuration in this Laptop?
Question 2: Should i use DDR3 instead of DDR3L RAM in this Laptop?
Question 3: Which RAM is best supported with this Laptop, Kingston or CORSAIR Vengeance?

Note: I am using Ubuntu on this Machine.

A:Dell Inspiron 5521 | RAM Upgrade | Memory Module

1. Yes, albeit at a performance penalty.  It's designed for a pair of matched modules.
2.  Either will work by itself.  Don't mix DDR3 and DDR3L though -- if you have DDR3, use that; if L, use that if you're adding a module.
3.  Crucial is hard to beat particularly given its compatibility guarantee when purchased through its memory configurator.  Anything else- ask the vendor about compatibility guarantees (or be sure you understand the possible restocking charge if a return is required).

1 more replies
Answer Match 50.4%

Good day to all. Can someone please assist me, advance thanks..

I bought a PC with MSI mainboard, N430GT, with 2-2GB Kingston KVR1333D3N9/2G installed RAM (=4GB), 500GB HDD.
Everything works smooth until I read that I could upgrade memory up to 16GB max. BTW my OS is Win7 64 Ultimate.

So I decided first to buy and install 2pcs-4GB Kingston KVR1333D3N9/4G (=8GB), for a few days everything works fine as expected, I shut it down one night and the following day restarting my PC, it turned BLUE with messages., and then on as often as every 5 minutes or less it turns BSOD.

I asked my friends and told me to do a clean OS reinstallation and I did that, but the problem persisted as if nothing changed.

So I did a memory diagnostic and It noted that possible hardware problem.

I did immediately changed and swap back my original 2pcs-2GB memory, and surprisingly until this thread writing it is ok.

My mainboard supports dual channel (two slots only) and I want to know how could I checked which one of the two 4GB memory modules is not working, or is it safe to install only one 4GB memory to checked which of the two is working or both are not working?

Any immediate response is of great help. thanks.

A:BSOD after upgrading &/or installing new memory module on brand new PC

The Kingston Value Ram (KVR) is known to be marginal and not even work in some PC's. The regular Kingston memory is usually OK but none of the techies that I know will use or recommend the KVR.

Check the MSI (or whoever the motherboard vendor is) site for your motherboard model (you didn't list it so I can't check for your). The N430GT is your video card, not the motherboard. Most motherboard vendors list compatible memory for their motherboards. Best to use memory that has been certified for the specific motherboard.

6 more replies
Answer Match 50.4%

Hi,

I have a Tecra 8200 p3 (850 i think) that currently has 2x 128MB RAM.

The laptop only registers 128MB, so I think one of the sockets may be faulty.

I understand the maximum memory the tecra 8200 will address is 512MB, but can this be in a single Dimm, or must it be in 2x256?

Thanks

Ian

A:Tecra 8200 recognizes only one 128MB memory module

Hi

You can use 2 x 256MB memory modules 144-Pin PC133 SODIMM or 144-Pin PC100 SODIMM

Best regards

1 more replies
Answer Match 49.98%

Hello, I have a dell 8250 that i am pretty happy with but have noticed that i need more ram. I have 512 now but several programs that i run suck up much of it. I have just purchased 2 new 512 modules for this thing and plan on pulling the 256 sticks out and replace them with the new ones. My question is i know i need to put rambus in matched pairs but can i have a pair of 512 and a pair of 256? any ideas? also i was thinking about wiping out my main drive for a complete clean reinstall. Is that a little overkill? opinions requested. thanks for your time.

specs:
Motherboard:
CPU Type Intel Pentium 4A, 2400 MHz (18 x 133)
Motherboard Name Dell Dimension 8250
Motherboard Chipset Intel Tehama i850(E)
System Memory 512 MB (RDRAM)
BIOS Type Phoenix (04/22/03)
Operating System Microsoft Windows XP Home Edition
OS Service Pack Service Pack 1
Internet Explorer 6.0.2800.1106 (IE 6.0 SP1)
DirectX 4.09.00.0904 (DirectX 9.0c)
 

A:Solved: Rambus Inline Memory Module, 256, 533mhz, 128x16, 8c

rrlr420 said:

Hello, I have a dell 8250 that i am pretty happy with but have noticed that i need more ram. I have 512 now but several programs that i run suck up much of it. I have just purchased 2 new 512 modules for this thing and plan on pulling the 256 sticks out and replace them with the new ones. My question is i know i need to put rambus in matched pairs but can i have a pair of 512 and a pair of 256? any ideas? also i was thinking about wiping out my main drive for a complete clean reinstall. Is that a little overkill? opinions requested. thanks for your time.

specs:
Motherboard:
CPU Type Intel Pentium 4A, 2400 MHz (18 x 133)
Motherboard Name Dell Dimension 8250
Motherboard Chipset Intel Tehama i850(E)
System Memory 512 MB (RDRAM)
BIOS Type Phoenix (04/22/03)
Operating System Microsoft Windows XP Home Edition
OS Service Pack Service Pack 1
Internet Explorer 6.0.2800.1106 (IE 6.0 SP1)
DirectX 4.09.00.0904 (DirectX 9.0c)Click to expand...

Good question--try it--I don't think it will work, but all it can do is not boot.
 

2 more replies
Answer Match 49.98%

I boot my Hp machine, nothing shown on screen and "capslock & numlock 3 times blink"i tried hard reseting it / AC adapter and battery does not seem to be the reason of this issue. is it memory module error? how to fix it?

A:Memory module error capslock & numlock 3 times blink

@usmanm27? Try reseating the memory boards first."Just remove them and reinsert them." HP EliteBook 8530w Mobile Workstation - Remove/Replace Videos http://h20464.www2.hp.com/results.htm?SID=3781677&MEID=C773CE52-9448-4212-9A06-3FF8E456DBA7 REO

1 more replies
Answer Match 48.72%

I have upgraded one of my old computers from 512MB RAM to 1GB by buying another PC3200 DDR400 512MB module. Upon booting Windows XP after the installation of RAM, BSODs with various errors show up (sometimes before loading to the desktop, sometimes after the desktop has loaded). Some of the errors include: IRQL LESS THAN EQUAL error, and another error that has the word 'Page' in it (I forgot if it is Page fault or Page file).

I have traced this down to the BIOS Memory settings. Before the upgrade, I have set other settings to the optimal setting that the BIOS can allow me, by reading this guide: http://www.techarp.com/freebog.aspx , without any problems. Upon upgrading, setting the DRAM Command Rate to 2T will prevent the BSODs (before the installation of the new module, this setting was set to 1T and my system worked fine without any BSODs).

I am wondering if there is another way I can get my system to work while still setting the DRAM Command Rate to 1T. As I have seen from various websites like this one: (Techwarelabs.com)
http://www.techwarelabs.com/reviews/memory/memory_timings/index_3.shtml , there is a performance increase if the DRAM Command Rate is set to 1T. I also would like to know if the performance gain is not that significant and if it is better if I just leave it at 2T?

I am also wondering if module order matters (based from closeness to the processor) in performance and stability. I have found out thru Everest Home Edition that the ne... Read more

A:DRAM Command Rate BIOS setting Problem with Installation of New Memory Module

Put the slower one into Slot 1 - that ought to ensure it runs at that speed, not the faster sticks timings..

You could try resetting it to 1T if that proves stable. A slight bump in Ram Voltage probably wouldn't hurt - if your board has that Facility in the BIOS.

A quick way to test stablility is to run a 2m SuperPi - it's not foolproof, but if it passes, you know you're on the right track. If you get errors, it's still suss, and you might want to run a MemTest on each stick individually - although it's new, it may still be faulty!
 

3 more replies
Answer Match 46.62%

I have an athlon xp2200 (266) and I had 512MB pc2100 (266) and everything was great. I replaced the memory with kingmax pc2700 (333) which i know is supported by my 7VJL deluxe apogee with KT400 chipset, but ever since then, it periodically locks up on me.

Any ideas? Maybe just bad memory?
 

A:is it bad to have 333 memory and 266 processor?

sounds like you may have bad memory. you can check by downloading memtest and running it.


http://hcidesign.com/memtest/download.html
 

7 more replies
Answer Match 46.62%

$1000 is my cap on a laptop. It's came down to either 1GB of memory and an Intel Core 2 Duo 5300 or 2GB of memory and an Intel Core Duo 2350. Which would you choose?
 

A:Would you buy a better processor or more memory?

I'd probably go for the memory.
 

1 more replies
Answer Match 46.62%

I recently upgraded to an AMD 3800 X2 (from sempron 3000)
I had 1.25 gig before.
Would it be sensible to upgrade to 2.25 gig?

I just noticed it seem to be using more memory.
However there is no real reason for this?

Or is there?

I have already ordered an extra gig so it's bit of a mute point.


Interesting I was just looking at memory usage

I have total 1309mb
available 118mb


Now I used to have a about 700mb available on the single core IIRC. It had been creeping up though.
 

A:More memory for a X2 processor

I'm not sure why your memory usage has increased so sharply. Was there any software new software installed?

However, an extra gig of RAM will not hurt.
 

2 more replies
Answer Match 46.62%

I finally decided it's time to throw in another stick of ram and while I was browsing, I talked myself into a new processor too

current setup:

epox 8rda+ (non-pro) motherboard
crucial cmx512-3200c2
amd athlon xp 2100+ w/ huge copper heatsink & ys tech 80mm variable speed fan

I'm getting another stick of the crucial and an athlon xp 3000+ - but what I want to know is will the current hs/fan combo work, should I get something new, or go with the retail hs/fan that comes with the processor?

thanks in advance
 

A:new processor and memory

11 more replies
Answer Match 46.62%

Hi,
I have an Asus M2N32 SLI Deluxe mb, an Athlon 64 X2 5000+ processor, an OCZ 700W PSU, 4GB RAM, and an Nvidia 8800 GTX 768MB video card. The system is 1-1/2 years old. Recently I've experienced getting no video upon reboot, so I disconnect the cable from the video card until I see that the computer is ready for log in, then reconnect the cable, and I get high resolution video (even in safe mode). The computer worked beautifully for 18 months. Now, if I try to install the video drivers, I get an error message saying that Nvidia can't locate the drivers for my hardware, and quits. I got the video drivers to install in safe mode, but then when I boot up, the resolution changes to 8 bit color, and 640X480 max. As soon as I uninstall the video drivers, the resolution changes back to 32 bit color, and 1280X1024. I've RMA'd the MB, the video card...tried to put a different video card in, tried both PCIe slots, and so far no luck. I even bought another MB (same type). No tech support has been able to diagnose this. I'm also noticing that when I boot up now, I get the usual single beep followed by 4 quick ones. I'm really frustrated, and don't want to keep shelling out money for equipment that's not old enough to replace!

Thanks for any input!
5245
 

A:MB, processor, memory, or PSU?

The only thing I can think of that might be problematic is running all 4 gig of RAM (if its a 32 bit system). Have you tested the memory and have you tried setting the whole system up on just 2? Using all 4 sets up the potential for conflict between RAM and reserved video address space if all is not right.
 

2 more replies
Answer Match 46.2%

 Hello , Product  : HP ENVY Ultrabook 4-1046txCurrent Wifi Module : Broadcom 802.11 b/g/n I need to upgrade my wifi module to a new dual band module preferably the Intel one.http://www.intel.com/content/www/us/en/wireless-products/dual-band-wireless-ac-7260-bluetooth.htmlCould anyone confirm that whether my laptop is Whitelist or not ?  Thanks in Advance !

A:Upgrade Wifi Module to a new Dual band module

Hi, Your machine was built long way before mid 2014. The chance to change wireless card is from slim to none. Do you know the whitelist story don't you ? Regards.

2 more replies
Answer Match 46.2%

When I boot up, the fans, cd-rom and everything runs, the cd-rom will open and close and I've taken the hard drive out and installed it into another case and it worked perfect. But there isn't anything but a black screen on my monitor. I've replaced the power supply box and it's still doing the same thing as before.

Attribute
Properties

Video graphic
PCI local bus

Controller
Intel 810

Video memory
10 MB shared system memory, integrated graphics, Not upgradable

Any help would be appreciated...Thanks

One more thing, how do I reseat the processor?
 

A:Reseat the Processor and Memory

6 more replies
Answer Match 46.2%

Hi, im finally going to upgrade my system in July and was wondering if anyone can suggest a new mainboard, CPU and memory. My budget is £150 for my mainboard, £230 for a new CPU and £100 for memory. I am leaning toward the Intel Core I7-2600 socket LGA1155 for my CPU choice. Anyone got any suggestions on what motherboard and memory would go good with my CPU choice?
 

A:Looking for new mainboard, processor and memory

How do you convert pounds into US dollars?
 

4 more replies
Answer Match 45.78%

I did a test at pc pitstop and it show that I have very poor disk performance, low processor performance, low memory performance, and low video performace. (23 FPS)

I have a HP Pavilion 6350 (WIN98) with a AMD-K6-2/333 processor a Gforce2 MX400 with 256 MB of ram and Road Runner. My comp runs really slow and every time i try to play a game like counter strike I run on around 23 frames per second, the lag is really bad. I have tryed defraging and that doesnt work. I did the PC pitstop test and it said my disk speed is bad would that effect it and how could i fix it? I can send u the resualts of the test if you want them.
 

A:low disk performance, low processor per., low memory per., low vid per.(23 FPS)?

16 more replies
Answer Match 45.78%

Hello,
Could someone please help me? I am looking to upgrade my pc but have a conundrum.

I am torn between an

Intel Q9550 Core 2 Quad Proccessor - 2.83 GHz,12MB L2 Cache,1333MHz and

the AMD Phenom II X4 955 Black Edition Quad-Core Processor - 3.20 GHz,8MB Cache,Socket AM3,125W,45 nm

Which is better do you think?

If I opt for the AMD the I have to revamp the memory to DDR3 to go with the AM3 motherboard (790gx has been recommended). I have seen ddr3 advertised "for i7 motherboards" in the blurb. Is it true that all ddr3s will fit in any ddr3 compatible motherboard or are there specific types for specific boards and processors?

I know that the intel will need a new motherboard (775 socket-ish?) but assuming that it will still use ddr2 mem. - the memory i already have...

Though i know very little about the subject I am rather interested in your opinions and facts etc.
Thank you in advance.
 

A:Solved: Which processor... memory... board?

10 more replies
Answer Match 45.78%

At the moment my kit stands at:

ECS KV1 Deluxe
AMD Athlon 64 Processor 3000+
Corsair Value Select 1GB PC3200 Non-ECC 184Pin CL3
Radeon x700 Series
Seagate Barracuda 7200.9 Hard drive - 250 GB
Sony DVD RW DRU-810A
Sony CD-RW CRX230EE
WinTV-NOVA-T
Hiper Type R 580W
View Sonic VX924
Thermaltake Damier V5000A Black Series

I am looking at upgrading my motherboard/processor/memory only, have been looking at some motherboard bundles on Novatech.co.uk for around the £150-£200 mark but nothing really takes my fancy.

I've like something with a dual core processor, lots of USB ports (both externally and internally as I have two USB ports on the outside of my case) , firewire ports (again inside and out), and can support all my current hardware.

Any suggestions?
 

A:Upgrade Motherboard/Processor/Memory Only

8 more replies
Answer Match 45.78%

This is kind of bothering me. My CPU usage always seems to be under 10%, while my Memory is always over 50%. In Vista my CPU usage was much more (30-40%) and my memory was lower (35-45%).

Is this 7 just being better with the processor and worse with the memory, or is it just reading it wrong?

A:Super Processor, or Slow Memory?

  
Quote: Originally Posted by mSeliga


This is kind of bothering me. My CPU usage always seems to be under 10%, while my Memory is always over 50%. In Vista my CPU usage was much more (30-40%) and my memory was lower (35-45%).

Is this 7 just being better with the processor and worse with the memory, or is it just reading it wrong?


im guessing worse with the memory but i dont see how it could be taking up that much without running a lot of extra programs

9 more replies
Answer Match 45.36%

Just wondering if possible to upgrade my memory and processor.......  hp pavilion dv7 1260us?????

More replies
Answer Match 45.36%

Hi all,
Previously I Installed Windows 8 Pro on my PC and another Same PC of my brothers.... Both PCs are exactly same
i.e. Compaq Presario SR1924IL except our RAMs and Hard Disk... He has 1.43 GB Ram and I have only 1 GB... He has 160 GB hard drive and again, I have 80 GB Hard Drive but when We installed Windows 8 Pro on our PCs the System Properties Are Different... We have Pentium D processor which in His Case is 2.80 GHz and in my case it's 2.67 GHz.. Can Someone Please Let me know what is gone wrong??? I am irritated with this processor memory... Please Someone Give me a Solution.... ...

Thanks For Reading.....

A:System Properties Showing Low Processor Memory !! ?

Processor memory, what's that ? Are you running 32 bit or 64bit windows ? With so much RAM you should be both using 32bit version. The rest of it I don't understand what you are talking about. How much physical memory do you have on each computer. Also check BIOS in both of them and make sure they are both set identically.

9 more replies
Answer Match 45.36%

This is a Dell N5030 laptop running Windows 7 sp1 with dual pentium at 2.3 gHz and 3gb of RAM.  Conventional methods have failed to identify the problem, which is that while at full idle, cpu usage runs around 50% and physical memory usage is around 97%.  Please help with this slower than molasses computer!  Here's the log:
 

DDS (Ver_2012-11-20.01) - NTFS_AMD64
Internet Explorer: 10.0.9200.16576  BrowserJavaVersion: 1.6.0_30
Run by Amie at 22:23:34 on 2013-05-26
Microsoft Windows 7 Home Premium   6.1.7601.1.1252.1.1033.18.3034.71 [GMT -4:00]
.
AV: avast! Antivirus *Enabled/Updated* {2B2D1395-420B-D5C9-657E-930FE358FC3C}
SP: avast! Antivirus *Enabled/Updated* {904CF271-6431-DA47-5FCE-A87D98DFB681}
SP: Windows Defender *Enabled/Updated* {D68DDC3A-831F-4fae-9E44-DA132C1ACF46}
.
============== Running Processes ===============
.
C:\Windows\system32\lsm.exe
C:\Windows\system32\svchost.exe -k DcomLaunch
C:\Windows\system32\svchost.exe -k RPCSS
C:\Windows\System32\svchost.exe -k LocalServiceNetworkRestricted
C:\Windows\System32\svchost.exe -k LocalSystemNetworkRestricted
C:\Windows\system32\svchost.exe -k LocalService
C:\Windows\system32\svchost.exe -k netsvcs
C:\Windows\system32\svchost.exe -k GPSvcGroup
C:\Windows\system32\svchost.exe -k NetworkService
C:\Program Files\AVAST Software\Avast\AvastSvc.exe
C:\Windows\System32\spoolsv.exe
C:\Windows\system32\svchost.exe -k LocalServiceNoNetwork
C:\Program Files\Realtek\Audio\HDA\AERTSr64.exe
C:\Prog... Read more

A:Virus hogging processor, memory usage.

Hi n8jk, to Bleeping Computer.
My name is Jason and I'll be helping you with your computer problems. You can call me by my screename jntkwx or Jason is fine.
Some things to remember while we are working together.
Do not run any other tool untill instructed to do so!
Please do not attach logs or put logs in code or quote boxes (unless explicitly asked to)
Tell me about any problems that have occurred during the fix.
Tell me of any other symptoms you may be having as these can also help.
Do not run anything while running a fix.
If you don't understand a step, please ask for clarification before continuing with any future steps.
In the upper right hand corner of the topic you will see the Follow This Topic button. Click on this then choose Receive Notification Immediately and then click Follow This Topic and you will be sent an email once I have posted a response and make the cleaning process faster.Note to others: The instructions here are intended for the person who began this topic. If you need help, please create your own topic in the appropriate forum.
 
 
It appears Combofix has been run. Please post the Combofix log.  If it exists, the log will be located at C:\Combofix.txt 
 

14 more replies
Answer Match 45.36%

The explorer.exe process at time starts to use a constant of 50% CPU usage and over 300MB of physical memory....every time this occurs i have to end and restart the process...
Any thoughts on that? No virus has been detected by Kaspersky Antivirus 6
 

A:High Processor and memory usage by Explorer.exe

8 more replies
Answer Match 44.94%

One for all you "Experts"

Hey all, I'm new around here, and I joined because I have bad computer trouble, and maybe someone could identify my problem. The other day, I opened up my computer to put a stick of 512 Mb DDR Ram into it, and i found two 128 Mb DDR sticks already in there. So I took one of the 128 Mb Chips out, and put the 512 Mb in, mixing them up with each other. Anyways, when I turned on my computer to boot it up, it made a bunch of wierd noises, like beeps, so I turned it off fairly fast. I took out the 512 Mb and put back in the old 128 Mb stick. Now whenever I push the button for my computer to come on, It will only make a long beep, pause for a second, then keep making the beeps, over and over again, the screen does not light, the LED stays orange. If anyone could help, anything is appreciated, Thanks.

- Thread moved & title edited
Didou
 

A:Installing new memory module (One for all you "Experts")

Take out all the sticks of ram, and then out in the 128 and 512. Be sure to take all of them out first though, and they are pushed ALL the way down, it requires some force.

What I do is, line up the RAM with the slot, then just push down hard on the ram until the clips at the side automatically come up and clip the ram into place
 

11 more replies
Answer Match 44.52%

Hi folks! I would like to know what is the fastest processor supported by Pavilion dv4-2173nr laptop. I would also like to know what is the maximum RAM memory that can be installed in this same laptop. Thanks in advance for the answers.

A:Pavilion DV4-2173nr fastest processor and memory upgrades

Hi, Please use Maintenance and Service Guide (second manual) on the following link:      http://support.hp.com/us-en/product/HP-Pavilion-dv4-Entertainment-Notebook-PC-series/4074361/model/4... Pages 1 to 3 should give all information you need. Regards.  

1 more replies
Answer Match 44.52%

Hello,

My laptop has a monitor problem. So I have now Dell c640 but would like to change some stuff like memory and processor from that other computer. I would like to know if it will be compatible with the dell device.

The processor from the other computer that I have is a Intel Core Duo (2M Cache, 2.00A GHz, 533 MHz FSB)

And the memory is SAMSUNG 1GB 2RX8 PC2-5300S-555-12-E3 DDR 2

can i use it in the dell computer?

the motherboard of the dell computer is:
Model: Dell Latitude C640
Chipset: Intel845D/MP (Brookdale) + ICH3-M
The Central Processor right now on the dell computer is: Intel Pentium 4-M-1800 (1800.0 MHz)
 

A:Add new Processor and memory to Dell c640 form another laptop

No.
 

1 more replies
Answer Match 44.52%

I would like to upgrade my Compaq Presario 2286 by increasing memory from 96 RAM to 256 RAM...and also to increase the clock speed as high as my computer will permit. I believe the max speed it will take and operate properly is 1.08 -- but wonder if I can go higher. Also, would like to know what processors and memories are compatible with my model. Any particular recommendations?
 

A:UPGRADING COMPAQ PRESARIOI 2286 processor and memory

11 more replies
Answer Match 43.68%

DR3-1333 Or DR3L-1333

Where can i obtain the exact same model of memory for CHEAP price? I read online someone got 4GB for 5$!! But i only finding some that cost 134$ of this kind??? What is this ridiculousness??

A:Memory upgrade for Celeron j1900 Processor 1x4GB DR3L-1333?

Anyone? Help? Is there no reasonably priced memory for this computer model worth getting? I dont need 200$ workstation server memory! just basic home user computer memory

2 more replies
Answer Match 43.68%

Hello,
 
My computer is running very slow, with over 50% of the ram and processor being occupied when I am not running any programs.  I've run Malware Bytes and Spybot S&D but the problem persists.  If any one could help me identify the issue, it would be greatly appreciated.
 
Thank you so much!

A:Spybot SD and Malware bytes not removing problem. Huge memory and processor use

Hello, Welcome to BleepingComputer.I'm nasdaq and will be helping you.If you can please print this topic it will make it easier for you to follow the instructions and complete all of the necessary steps in the order listed.===Open notepad (Start =>All Programs => Accessories => Notepad). Please copy the entire contents of the code box below.
start

CloseProcesses:

Winlogon\Notify\SDWinLogon-x32: SDWinLogon.dll [X]
ShellIconOverlayIdentifiers: [00avast] -> {472083B0-C522-11CF-8763-00608CC02F24} => No File
FF Plugin: @microsoft.com/GENUINE -> disabled No File
FF Plugin-x32: @microsoft.com/GENUINE -> disabled No File
FF user.js: detected! => C:\Users\Jasmin\AppData\Roaming\Mozilla\Firefox\Profiles\e2f3yfx5.default\user.js
CHR StartupUrls: Default -> "hxxp://gmail.com/", "hxxp://www.trovi.com/?gd=&ctid=CT3324790&octid=EB_ORIGINAL_CTID&ISID=MDFF64E6D-13EC-47EC-82E4-165202982C05&SearchSource=55&CUI=&UM=5&UP=SPED3792B9-86B8-411D-A2C5-15BD26359EC7&SSPV=SP21511A_sp_ch"

End
Save the files as fixlist.txt into the same folder as FRSTRun FRST and click Fix only once and wait.Restart the computer normally to reset the registry.The tool will create a log Fixlog.txt please post it to your reply.===Please download AdwCleaner by Xplode onto your Desktop.Close all open programs and internet browsers.Double click on AdwCleaner.exe to run the tool.Click the Scan button and wait for the process to complete.Click the Report butto... Read more

2 more replies
Answer Match 40.74%

I ran Malwarebytes several times and always get two infections. One is Trojan.TDSS with the Catagory: Memory Module and Items: \\?\globalroot\systemroot\system32\SKYNETnpoysrwi.dll. The other is Trojan.TDSS with the Catagory: File and Items: \\?\globalroot\systemroot\system32\SKYNETnpoysrwi.dll. I make sure they are checked, remove them, restart as prompted, rescan and get the same result. I have repeated this process several times. I tried another method from another site of getting rid of these by disabling the driver in the device manager and running "Avenger" to delete the driver and then I believe reinstall it. It is currently still disabled and the icon has an exclamation on it. I hope this helps you. Thanks.
DDS (Ver_09-06-26.01) - NTFSx86
Run by Mr. Amazo at 11:04:21.00 on Sun 06/28/2009
Internet Explorer: 7.0.5730.11
Microsoft Windows XP Professional 5.1.2600.3.1252.1.1033.18.1014.253 [GMT -4:00]

AV: AVG Anti-Virus Free *On-access scanning enabled* (Updated) {17DDD097-36FF-435F-9E1B-52D74245D6BF}

============== Running Processes ===============

C:\WINDOWS\system32\svchost -k DcomLaunch
svchost.exe
C:\WINDOWS\System32\svchost.exe -k netsvcs
C:\Program Files\Intel\Wireless\Bin\EvtEng.exe
C:\Program Files\Intel\Wireless\Bin\S24EvMon.exe
C:\Program Files\Intel\Wireless\Bin\WLKeeper.exe
svc... Read more

A:Infected with Trojan.TDSS Memory Module and Trojan.TDSS File

Reformated drive, so no reply is neccessary. However it would be nice to know what is required for this fix. Thanks.

2 more replies
Answer Match 39.06%

I have a motherboard that has a FSB of up to 400MHz.
My processor is an AthlonXP 2200 which can only run at 266MHz
My memory is 256MB DDR DRAM PC2700
SisSoftware Sandra testing tells me my memory speed and processsor speed do not match. Question is: Does this really matter? I know a processor upgrade would sort it but a)the computer seems to run fine and b) I daren't try to sneak ANOTHER pc purchase past the wife! (just yet);-)
 

A:Memory speed faster than processor speed

7 more replies
Answer Match 37.8%

So, i got this message after i upgraded my Asus Notebook to Windows 10 Home from 8.1. What got me to check this was having my laptop Hard Shutdown when the power was at 100% and the laptop had been on the charger all day, plus the CPU temperature was normal. I went into event viewer to see if there was any ACPI error's listed and this came up.

The exact Error that's provided via Event Viewer: Collaborative processor power controls on processor 5 in group 0 are disabled due to a firmware problem. Check with the computer manufacturer for updated firmware. This message is provided for each of my Processor Cores

Unfortunately, there are no new Firmware Updates for my laptop model from Asus. Last one was pushed in October 2014. Very odd seeing as i got this new in December 2014.

I want to know if this is something serious, or if i should just ignore it. An error having to due with Kernel Level Power Controls seems serious to me.

System Info:

Asustek N56JN-MH74 Notebook
Processor: Intel(R) Core(TM) i7-4710HQ CPU @ 2.50GHz, Intel64 Family 6 Model 60 Stepping 3 4Core 8 Thread
Ram: 8GB (8075 MB)
Video: Intel Onboard 4600 1024 MB / Nvidia GeForce 840m
OS: Windows 10 Home Upgraded from Windows 8.1

So is there anything that i can do, or do i just have to wait for asus to publish a new Firmware Update, even though it's probably likely they won't. Thanks in advance guys.

A:Collaborative Processor Power Controls for Processor are disabled after upgrade

Hi and Welcome to TSF!

See if this finds any new drivers:

Intel? Driver Update Utility

1 more replies
Answer Match 37.8%

So, i got this message after i upgraded my Asus Notebook to Windows 10 Home from 8.1. What got me to check this was having my laptop Hard Shutdown when the power was at 100% and the laptop had been on the charger all day, plus the CPU temperature was normal.

The exact Error that's provided via Event Viewer: Collaborative processor power controls on processor 5 in group 0 are disabled due to a firmware problem. Check with the computer manufacturer for updated firmware. This message is provided for each of my 8 Processor Cores

Unfortunately, there are no new Firmware Updates for my laptop model from Asus. Last one was pushed in October 2014. Very odd seeing as i got this new in December 2014.

I want to know if this is something serious, or if i should just ignore it. An error having to due with Kernel Level Power Controls seems serious to me.

System Info:

Tech Support Guy System Info Utility version 1.0.0.2
OS Version: Microsoft Windows 10 Home, 64 bit
Processor: Intel(R) Core(TM) i7-4710HQ CPU @ 2.50GHz, Intel64 Family 6 Model 60 Stepping 3
Processor Count: 8
RAM: 8075 Mb
Graphics Card: Intel(R) HD Graphics 4600, 1024 Mb (NOTE: my laptop has an Nvidia GeForce 840m Chip as well, but it did not detect that for some reason)
Hard Drives: C: Total - 381546 MB, Free - 260544 MB; D: Total - 550702 MB, Free - 543877 MB;
Motherboard: ASUSTeK COMPUTER INC., N56JN
Antivirus: Windows Defender, Disabled (Have not had time to get antiviral software yet)

So, is there anything i ca... Read more

More replies
Answer Match 37.8%

I recently upgraded to a HP,Media Center editon pc, Windows XP, AMD Athlon 64 3800+2.4 GHz Processor.

When trying to install Photoshop Album 1.0, I receive this message, "This operating system is not supported by Adobe Photoshop Album. We support Windows 98SE, ME, 2000 , XP Intel Pentium III or 4 processor".

Could my problem with installation be the Athlon processor? When purchasing this computer, our salesman convinced us that the Athlon was just as good as the Pentinum Processor. Any thoughts on this? My computer is less than a week old and having serious thoughts about returning it. I have had problems with other installations. Am I to expect more problems with software and the Athlon processor. Any helpful suggestions will be appreciated. I am getting desperate for advice about the processor.
 

A:Athlon Processor versus Pentinum Processor in Windows XP

What the message is telling you is that Windows Media Center Edition 2005 is not one of the operating systems that Adobe Photoshop Album 1.0 supports. It has nothing to do with whether an Intel processor or an AMD processor is installed. I checked the system requirements for the newer version 2.0, and it also is not supported by Windows MCE 2005.

By the way, Adobe Photoshop Album 1.0 has a 13.5 MB patch for it and will upgrade it to version 1.0.1. You can get it from here.

-------------------------------------------------------------------------------------
 

3 more replies
Answer Match 36.96%

I need to order a new desktop for my office to replace a 3 year old machine that runs at 3.2 Ghz. The new machines that Dell offers only has this option:

Intel® Core™2 Extreme QX6700 (8MB L2 Cache,2.66GHz,1066 FSB)

I don't think there is a standard measuring stick that is used to compare all the processor speeds that I can find or understand. I work with CAD programs that use up a lot of resources and I typically get the fastest available and max the RAM. With all the latest software that I have to install, I need the new machines to run faster than the ones they replace.

Can anyone tell me how this 2.66GHz processor compares to my current machine? I don't have the exact specs for it, this is what it lists on the dell support site for my system - PROCESSOR, 80532K, 3.2GHZ, 1M, 533, M0.
 

A:How does this processor speed rate against a 3.2Ghz Processor

9 more replies
Answer Match 36.96%

Quad processors are darn expensive. You can have a hand in helping me build my new laptop.

Speed is a priority: when I use my computer for PLEASURE, I can deal with an occasional slowdown. When I use my computer for a WORK or a SCHOOL project and I experience a slowdown, I feel like breaking bodies or punching a hole in the wall.

I'm buying a new laptop. I'll be using it primarily for work and school. I'd say 80% of the time that I use the laptop it will be used for serious 9-5 business stuff, primarily work and school.

That's why when I customize my new laptop I'm going to customize it with 8 gigs of RAM and a quad core processor, to have as much speed as possible and as high a flow rate as possible. Is that a good build strategy?

My work/school laptop will:

>be used for heavy Internet duty

>be used heavily for programs like Dreamweaver, Photoshop and Flash

>i will not be using it for computer games but note: if i have to sell the laptop on Craigslist in a year or two I'd like this laptop to appeal to gamers so I can sell it quicker, faster

>i don't have a lot of disposable income. The quad processor costs a few hundred dollars more. Since I'll be using my computer for work and school, and since I might be making more money a year from now, If I have to (and with your advice) I'll pay the extra cost
 

A:Decision time: should I buy a quad processor or a duo processor?

6 more replies
Answer Match 36.96%

Can any body tell me the main diff between the core 2 duo processor and core 2 duo processor with centrino.

Thanks
_______
 

A:Diff between centrino processor and core 2 duo processor

In a word nothing, the centrino branding does not refer to any specific additions to the processor, it is simply a label that is attached to laptops which use intel branded processor, integrated graphics and wireless chips.

Centrino is more of a marketing tool that Intel use to boost sales of their graphics and wireless chips, so you can pretty much ignore it
 

2 more replies
Answer Match 35.7%

Hello everyone,

I want to build a new system, and I was wondering just what the differences between a sever processor and a desktop processor are.

Would I see gaming performance decrease by using a Quad Server Core or a Quad Desktop Core?

I wanted to build a dual socket server core and have 8 physical cores.

Thoughts?
 

A:Server Processor Vs. Desktop Processor

I dont think any games are designed to take advantage of a dual socket setup. Windows Server OS's are designed to take advantage of dual socket setups. Some newer games are coming out which take advantage of single socket dual or quad core setups on desktops. A server based PC would not gain any performance for games IMO. You are better off investing the extra $ in a good video card.
 

5 more replies
Answer Match 34.02%

---------------
Display Devices
---------------
Card name: NVIDIA GeForce 8600M GT
Manufacturer: NVIDIA
Chip type: GeForce 8600M GT
DAC type: Integrated RAMDAC
Device Key: Enum\PCI\VEN_10DE&DEV_0407&SUBSYS_15151043&REV_A1
Display Memory: 2028 MB
Dedicated Memory: 237 MB
Shared Memory: 1791 MB
Current Mode: 1920 x 1200 (32 bit) (62Hz)

------------------
System Information
------------------
Time of this report: 4/22/2008, 14:37:30
Machine name: NICK-PC
Operating System: Windows Vista™ Ultimate (6.0, Build 6001) Service Pack 1 (6001.longhorn_rtm.080118-1840)
Language: English (Regional Setting: English)
System Manufacturer: ASUSTeK Computer Inc.
System Model: G2S
BIOS: Default System BIOS
Processor: Intel(R) Core(TM)2 Duo CPU T7700 @ 2.40GHz (2 CPUs), ~2.4GHz
Memory: 4094MB RAM
Page File: 1506MB used, 6857MB available
Windows Dir: C:\Windows
DirectX Version: DirectX 10
DX Setup Parameters: Not found
DxDiag Version: 6.00.6001.18000 64bit Unicode

A person in my thread here: http://forums.worldofwarcraft.com/thread.html?topicId=5784544444&postId=59801079620&sid=1#24

said:

That doesn't look right , my 8800GTS 512 displays

Memory:512 MB
Dedicated Memory: 512 MB
Shared Memory: 512 MB
Could you have bad videocard memory? Or maybe reinstal direct X? Click to expand...

So I'm not sure where to start and I'm hoping someone here can point me into the right direction as to what it is I need to do to fix this problem I've been having wit... Read more

A:Display Memory,Dedicated Memory,Shared Memory not consistant

6 more replies
Answer Match 32.34%

Hello Everyone,

I have recently purchased Easy Media Creator 7.0 to download some files on a CD disk. I have a Dell 4100 Inspiron Notebook, XP home edition windows system.

I installed the easy media Creator 7.0 on my notebook. I used the "copy files to disc. " I dropped all the files down in the loading area and then , put in a CD-R disc in the disc holder re: the 24XCD-Rom Module, and Hit "Burn". There is a sign that come up " no recorder".

I couldn't get it to record and burn any of my files. So I thought I had the wrong CD. So I purchased a CD-RW and inserted it into the D Drive (re: CD-Rom Module) in my notebook and I still got the sign, "no recorder". The "No recorder" shows up on the little Icon of the drop and drag thing that is setting on the desktop.

I looked under the Media Manager and also the Disc Copier re: under the "Selecting the destination". I notice when I tried to burn the CD, there was no destination printed on it. I went back under the disc copier window and tried to enter in the "recorder" information under the Destination area but it wouldn't let me enter in any information here. It was a gray area and no where to input the info.

I am totally confused!!

Question: My notebook came with a 24XCD-Rom Module only (re: LG CD-Rom Crn8245B), and this is what I am using to try to record things. Is this strictly for playing and not recording?

I am convinced I don't have... Read more

More replies
Answer Match 32.34%

I have a 4 year old HP Laptop. This summer the dreaded blue screen came on briefly and then the computer went blank. Screen was on but no icons. Shut off computer it would not come back on. Just the screen, no icon. Took it for repair and the tech took out one of my 256 Ram modules. He said it was bad and suggested I return it back to Kahlon co. I had it in for two years with no problems. I returned it to Kahlon with explanation and have not heard from them. That was in September. Called a few times and could only get promises. Module had lifetime warranty. Still waiting. Ordered new 256 RAM Module from OEM. Put it in slot and the same thing happened. E-mailed OEM for suggestions. The Rep. said to remove RAM Module that came with computer and put in new Module. I did and the computer works fine, but only on 256 RAM. Took a chance and put old Module in the other slot and bingo computer goes off. My question is: Can the slot be bad or is it a BIOS setting or what? Also, how do I rectify the situation without purchasing a new Laptop. Hate to do it, but thought I would ask first.
Also, cannot recommend dealings with Kahlon. I need the speed of 512RAM for my photography.
Thanx
 

A:Ram Module

Well if it was working fine then you put the old back in and it caused the problem again Its bad. would say it has nothing to do with the bios
 

1 more replies
Answer Match 32.34%

Hi peeps, merry xmas to you all ;p

I just installed 2 strips of DDR2, the exact make my Asus MB requires as the old ram that was in it was different speeds.

Originally it had 1.5gig so i repleced the 2 strips for 2x1gig strips of matcjing everything.

So switched PC on and now windows tells me i onlyhave 1 gig installed !

Cpuz tells me both are there and tells me the exact info that is required but windows only tells me i have 1 gig now when it said i had 1.5gig with miass matched ram ??

Puter seems smoother so my question is, :-

Is W7 32bit using 2gig or is it not ?

Why cant thing just work lol lol lol also on the ram it states it is PC2-4200 DDR2 Memory RAM DDR2-533 533MHz but if you check the cpuz file it states different .

Dont know what to do now. is the ram faulty ? miss labeld ? or what ?

Thanks for any ideas.

Here is the cpuz file.
 

A:Win 7 can't see one module of RAM

Ok hold the horses lol I took the slots out and swapped them round and proper made sure they were in, so now W7 tells me i have 2gig yey but cpuz still telss me they are PC2-5300 (333 MHz) and not PC2-4200 (533MHz) as the label says on the moduels.

Is Cpuz right or are the stick right ? i bought these off ebay from a reputable dealer so if there is an issue i need to resolve it cos if i paid for 533MHz and i only got 333MHz then i need a refund os some sort dont i ?

Thanks again.
 

2 more replies
Answer Match 32.34%

Hello, Someone please help me. I can not connect to Internet. I called ATT (SBCGlobal) they say there is no problem that my connection is fine. I log in and get a "YPC Module has encountered a problem and needs to close sorry for the inconveinence.
What is this?How do I get rid of it so I can get back online?
Help
Please
Michele

A:Ypc Module

This has to do with Yahoo parental control. Maybe turn it off? look here. http://www.google.com/search?hl=en&q=y...mp;aq=f&oq=

1 more replies
Answer Match 32.34%
Q: Module

I am having a problem with my one of my dll's or modules i'm not sure. I get a message saying Error loading c:\progr~1\yahoo!\common\YMMAPI~1.DLL

The specified module could not be found.

How can I fix this problem? Thanks for taking the time to read thes thread and the time for helping me.

A:Module

You probably just need to reinstall whatever yahoo devices you are using (yahoo toolbar, yahoo messenger, etc...) and if you dont' want them install them, then uninstall them properly through Add/Remove Programs

1 more replies
Answer Match 32.34%

My Zb Module has stopped working. What must I do to get it working again. This happens when I try to open Canon ZoomBrowser.

Henyhaus
 

A:Zb Module

Henyhaus said:


My Zb Module has stopped working. What must I do to get it working again. This happens when I try to open Canon ZoomBrowser.

HenyhausClick to expand...
 

1 more replies
Answer Match 32.34%

I was trying to upgrade my Gateway SOLO 1450 from by adding a 512 MB chip to the already existing 128 MB. I called Gateway and also went through the crucial.com memory chip selector to make sure I got the right one.

I purchased a KINGMAX 512MB PC133 chip from newegg. When I put the chip in along with the 128 chip. It starts to boot and then I get the following blue screen of death message:

STOP C0000218 {Registry File Failure} The registry cannot load the hive (file): \systemroot\system32\sonfig\DEFAULT or its log or alternate. It is corrupt, absent, or not writable. Beginning dump of physical memory.
Physical memory dump: (countup) Contact your system admin or technical support group for further assistance.

If I take the upgrade ship out then the computer boots fine with the message that it recovered from a serious error:

BCCode : 1000007e BCP1 : C0000005 BCP2 : 80608809 BCP3 : F8A45A08
BCP4 : F8A45708 OSVer : 5_1_2600 SP : 0-0 Product : 768-1

I haver tried swapping the memory around and the same thing happens. I have tried booting with only the 512 memory and I dont even see a boot screen. When both modules are in the BIOS reads Slot1: 128MB Slot2: 512MB.

I have also tried to upgrade video drivers and repairing windows from a boot disk. When I tried to repair the drive, a message said the the C: drive was corrupt and unrepairable.

I was wondering if I just have a bad module or is it some other problem?? If it is a bad module, would the BIOS be able to read that it ... Read more

A:Is my RAM module bad?!?

I'm leaning toward a bad module, your spec say it can take 1024mb of ram in two slots, so i have to think a 512 stick is ok, if you tried the 512 stick alone in both slots and still no joy I would send it back for a refund.
 

1 more replies
Answer Match 32.34%

im having some trouble with my zoombrowserEX every time click into it it says zb module stopped working. in have windows vista basic.my computer skills are very basic.
thanks a mill
deetrav
 

More replies
Answer Match 32.34%

I want to create a PC Hardware Review link in the modules section of my PHP website. I, being a complete newbie at this, don't have the slightest clue what to do, and how to do it. I already have a PC Game Review link in the Module, and want to add the hardware one in with it. This is my website
 

A:PHP Module ?

6 more replies
Answer Match 32.34%
Q: Module

i was wondering how you made a for open automaticly when you open the acces file i tried by puting in the option explicit command and function openshiprec and also openform_shiprec
then the end function and it doesnt work what am i missing
 

More replies
Answer Match 32.34%

How do i find the driver for Intel(R) Pentium(R) processor N- and J-series / Intel(R) Celeron(R) processor N- and J-series EHCI USB - 0F34

More replies
Answer Match 32.34%

i had the same problem and i came across this page, these are the txt files
 

A:CPX.MODULE/CPX.EXE/Smart CPX

Hello,

They call me TwinHeadedEagle around here, and I'll be working with you.

Before we start please read and note the following:

At the top of your post, please click on the "Watch thread" button and make sure to check Watch this thread...and receive email notifications. This will send an email to you as soon as I reply to your topic, allowing me to solve your problem faster.
Please do not install any new software during the cleaning process other than the tools I provide for you. This can hinder the cleaning process. Please do not perform System Restore or any other restore.
Instructions I give to you are very simple and made for complete beginner to follow. That's why you need to read through my instructions carefully and completely before executing them.
Please do not run any tools other than the ones I ask you to, when I ask you to. Some of these tools can be very dangerous if used improperly. Also, if you use a tool that I have not requested you use, it can cause false positives, thereby delaying the complete cleaning of your machine.

All tools we use here are completely clean and do not contain any malware. If your antivirus detects them as malicious, please disable your antivirus and then continue.
If during the process you run across anything that is not in my instructions, please stop and ask. If any tool is running too much time (few hours), please stop and inform me.
I visit forum several times at day, making sure to respond to everyon... Read more

1 more replies
Answer Match 32.34%

Hi Everyone,

I rebooted my Window 7 machine yesterday and on restart, I got that old message "Specified module cannot be found" about a DLL named "nlpchulp.dll". I ran HijackThis to see if I could find out more about it but I didn't get much.

Here is what I got from the startup file...
Yfunofikahasafox = rundll32.exe "C:\Users\William\AppData\Local\Nlpchulp.dll",Startup
And here is what I got from the AnalyzeThis file...
O4 - HKCU\..\Run: [Yfunofikahasafox] rundll32.exe "C:\Users\William\AppData\Local\Nlpchulp.dll",Startup

Not a lot of help so far. Anyone have a clue what application this DLL is actually associated with? (probably a trojan or worse). I can post the logs if you think that would help, but there doesn't seem to be much else in there.

Thanks,
Tahoe

PS The first person that criticizes how I posted or what forum I posted in is getting one "upside the head"!

A:Specified module cannot be found

Hello and welcome to Bleepingcomputer.

I see where you posted about this same issue on another forum...google works wonders doesn't it?

I would like to say to you first of all Bleepingcomputer is a friendly forum where everyone here is treated with respect and as one of the family.

So with that being said you came to the right place for help with the respect you deserve.

If you permit me a few minutes to return with a reply for you that would be great, I just wanted you to know someone here is always willing to help you with a smile.

Bruce.

3 more replies