Tech Problem Aggregator

Printer test page half printed

Q: Printer test page half printed

Hi all

I have a HP officejet v45, which has had new hp cartridges installed recently. Alignment page printed and aligned. Colours on tis page where as normal. After this I could only print about 30% of a page going across the page. Tried printing test page which again only printed about 30% of normal. Have uninstalled printed removed drivers and software via ADD/REMOVE PROGRAMS in Control Panel.

Have used both the installation disc and a downloaded set of drivers and software from the HP website to reinastall the drivers to no avail.

I need the printer to print off CV's for an interview for a new job over the next few days.

HELP please........

Tahnks for any help on this matter. I am using XP SP3, recent updated via microsoft website.

A: Printer test page half printed

7 more replies
Answer Match 74.34%

thanks for your guide

how can I create a task to 'open a printer, print the test page at that specific printer and then shut down the printer' ?

I want to do this, so that the printer will be maintained and not break due to inactivity

thanks!

A:Create task to open printer, print test page, and shutdown printer?

Not understanding this part of your question ........ "not break due to inactivity"

7 more replies
Answer Match 72.24%

windows xp p4 256ram .....Epson stylus 600 I have to use the xp 's drivers, Epson has not updated. The printer ran fine For a month. Tonight halfway through a page it stopped. If I restart the pc it then does the same.... any ideas?? Thanks
 

A:printer quits half way through page

Does anything print or does the paper just hang half way through?
 

1 more replies
Answer Match 72.24%

I just hooked up a printer while we take our other in for repair. The printer we just hooked up is a Canon BJC-240. It is printing everything small and only on half of a page. IT's the entire document but, squeezed onto 1/2 of the page!
Any help appreciated.

Anne
 

A:Printer printing on half of page!

Did you go thru the add printer function and install the correct drivers for this printer, or did you just unplug the old one and pop this one in its place?
 

2 more replies
Answer Match 71.82%

I have an HP LaserJet 1020 attached to a WinXP Pro workstation via USB. I have an Intel iMac networked with the PC wirelessly. I can detect the LaserJet on the iMac just fine, and on the iMac, documents spool and even say they have printed (they show up in the "completed" section of the printer control panel).

So, the iMac thinks the document printed, but it never did. When I look at the print queue on the Windows machine, I see "Remote Downlevel Document" in it. I assume that the iMac is printing to a port instead of starting the Windows Print Spooler, and this is why it is showing up with this name.

When viewing the LaserJet's queue on WinXP, the downlevel document is "Printing," and "113k/113k" has been transferred. But the document never prints - if I try to "cancel" the document in the Windows print queue, it says "deleting" for a verrrrry long time. Documents can be printed just fine locally on the Windows workstation.

Thanks in advance!
 

A:Shared Printer says "completed," but no page printed

are you using windows workgroup printing? How are you connecting to the printer?
 

2 more replies
Answer Match 70.56%

i have hp laserjet 1005 MFP, it was working okay but suddenly while printing a number of pages, it started to erase the middle of the pages while the sides were pretty good!!!
it's still new so am pretty sure that the cartridge doesnt need to be replaced yet! and its the original cartridge by the way
i removed the cartridge and put it back and it printed again normally like 5 pages and then the old story!
the problem is that even if i take out the cartridge and put it bak in (which i have no idea how it helped b4) now it's no use!
this problem is now both while printing or photocopying!.. and when photocopying it greys the sides of the paper
so this is like really messed up! is there any help soon plz......
(well am not sure if this is the right place to post so if its not plz tell me)
 

A:Solved: HP Laserjet printer prints only half the page!

Actually, it's almost certainly the cartridge. If this is a new printer, you may have gotten the "starter" cartridge that doesn't have that much toner, yet another ploy to get you buying expensive consumables for the printer.

Take it out and gently rock it side to side, then back and forth, put it back in, and see if it prints a few pages again.
 

3 more replies
Answer Match 70.14%

I have an offiejet 7310. Printed the sample page (gourd in a basket on a tablecloth). Problem is how do you know what it "should" look like? There isn't an example on the screen saying this is what is originally intended. Hard to tell what those pumpkins and squash should look like since they come in many colors and the same with a tablecloth. I tried to find that picture online but good luck with that (unless someone else can post it)

A:printer test page question

I think those test pages are intended to see if you get a full print, if the ink is smeared, are the lines clean, etc.

Even if you found the pic, the color accuracy of your monitor would effect how close of a match you got.

2 more replies
Answer Match 69.3%

Hi all,

I have a 'Brother' Printer model HL 2040.
After downloading and installing updated driver, the printer prints the Test page. But upon trying to print a word document or copy of file from quickbooks, the printer sends out empty pages.

I tried this several times but same happens again.

All solutions appreciated.
 

A:Problem: Printer prints test page but Nothing else

Hi,

When I have installed printers in the past, the printer needs to be disconnected from the USB port until after the installation of the software. If you have not done this then I suggest that you uninstall the drivers and reinstall ( with USB cable disconnected )

Assuming that you have XP - is this the software that you have downloaded?
 

1 more replies
Answer Match 69.3%

Hi!
I have an HP Deskjet 940C printer. It only prints color when I print a test page; everything else I try to print is black and white only. Any suggestions?
Thanks!
 

A:printer prints color on test page only

9 more replies
Answer Match 69.3%

I have WINDOWS VISTA HOME PREMIUM 64 BITS and everytime that I turn on my printer (HP PSC1500 SERIES) a TEST PAGE IS PRINTED. This is turning annoying and wasting may INK and PAPER. If theres is something that you can help me to stop this, I will really apreciate it!!!!
Thanks in advance!!!!
 

A:Printer prints test page everytime....

http://h10025.www1.hp.com/ewfrf/wc/...c=en&product=1146336&tmp_track_link=ot_search
 

2 more replies
Answer Match 68.88%

*Note: I am not sitting at this computer, and can provide only limited information about it, as it is not in my state. I have some info, but not much.
We have a new network printer, an HP LaserJet P4515, which is on our network. We added it today, and installed it via adding a new TCP/IP port, the usual way that we install network printers. It works for three out of four users that we installed the printer with. The fourth user is not able to print the test page, it just says pending, then error- failed to print.
Please advise so these people can finish their daily work.
Thanks,
Nemesis General

A:[SOLVED] New Printer won't print test page for one user

*Bump*

4 more replies
Answer Match 68.88%

Hi,
I was wondering if someone could help me out with this issue im having with printing redirection. On my workstation computer I have installed an HP printer which works perfectly. Now I wanted to try Remote desktop printing redirection on my windows server 2012r2, it recognizes but when i try to send a print test page it would sent it then immediately vanishes i then tried giving the folder spool full permission which i did.I am completely stumped. I was wondering if someone had this issue or if someone could guide me what im doing wrong

Thank you.

A:printer redirection vanishing print test page

EDIT:
I ended up installing a virtual machine on the server with windows 8.1 the i RDP to the virtual machine and worked flawless no drivers were even needed to install. What i think might be the problem on the windows server is it uses the easy driver first rather then the driver of the device. But it was much easier putting a new virtual machine acting as a print server

1 more replies
Answer Match 68.88%

I have a home network with an XP system with a printer attached and shared. A Windows 7 laptop and my old XP laptop from work can print fine, but a new Windows 8 laptop won't print. Sharing from the XP system works as I can read files from the XP system on the new Win8 system. When I do an Add Printer on the Windows 8 laptop, I can see the network printer and install it and the driver so the printer shows up as installed on the Win8 system. The Print Test Page does not work nor printing from WordPad. I turned off the Firewall on the XP system in case that was the problem. I don't know what else to try.

A:Can add network printer, but Print Test Page does not work

Does the test page dissapear from the print queue as though it has been sent to the printer or does it just sit there waiting?

What port does it show under printer properties?

6 more replies
Answer Match 68.04%

This old printer worked wonderful. I would like to re-install it. When I send a test page to it Printer Settings reports One document in Que, Status Printing, but it doesn't print.

I have connected the printer with a parallel cable and in the printer window it said Ready Standby.

I download driver R166996 and unpacked it to C:/Program Files/Dell/Win32/PCL/English/dixblzi and clicked Open. It said Installation completed successfully.

I went to Devices and Printer, clicked on Add a Printer, selected Add a Local printer use Existing LPT1, Dell Laser Printer 3000cn PCL6; have Disk, and then I browsed to where I unpacked the driver. The installation Completed successfully.

Why can't I print a test page? I shut off the printer I ran Problem Solver. It cleared Que. I tried to print a test page again and it sent the Test page to the printer but it still didn't print.

I unplugged the printer, rebooted the system, plugged it in and tried to send a test page again. It still didn't print. How can it be that Windows 7 sees the printer, the printer reports everything is Ready and yet it doesn't print?

I believe the printer is in working order but something is wrong with the communications. Can someone help me.

A:Dell CL Printer model 3000CN will not print test page

Try to print form an application, like Word. If it doesn't work please post with detailed explanation of what didn't work, for example Printer not listed in available printers, File sent to printer but operation doesn't complete, a specific error message....

3 more replies
Answer Match 61.74%

Hi, I just purchased an used computer with Windows 7Home Premium x64, this is an HP Slimline s5610f. The problem that I have is with a Brother HL 2040 series printer. It gave me a really hard time to install the drivers that I downloaded from the Brother website I kept getting a "0x00000057" error and "could not find suitable driver for this printer" error. Finally I decided to take the driver folders for this printer from my wife's computer and copied them to my computer and put them in the drivers repository under System32 and was able to install the printer after that with no problems.

The problem that I have right now is that the printer won't print, even though it told me that the driver installation was successful.

1-the print button is grayed out
2-If I click "printer properties" it tells me that the drivers have not been installed and asks if I want to install them.
3-If I install the drivers at this prompt it tells me that the drivers have been successfully installed.
4-Now it lets me access the printer properties but when I click "print test page" either nothing happens or it tells me that it failed to print and access is denied
5-If i close printer properties and try to access it again it tells me that the printer drivers have not been installed.

I get the same results with the printer connected locally trough USB or on another computer through the network.
All the other computers in the house print to this printer witho... Read more

A:Printer problems print button grayed out - test print page fails

Hello and welcome Manuel. Now probably too obvious mate but is the printer showing up ticked as the default device in Printers and Devices? while 7 is up and running?.

5 more replies
Answer Match 61.74%

My dads H.P.printer, All in one PSC 1350 prints a test page every time he turns the printer off and on. It wastes so much color ink. I've searched all over the properties and cant see where there is a place to stop the test page. Other than leaving the printer on, is there a way to stop the test page from being printed? He only uses the printer once in a while, thats why he turns it off when he's not using it.
 

A:H.P. Printer - 1350 PSC - Help stop "test page" printing at startup

A little more information: He's using Window's Vista and has all the updated drivers.
 

1 more replies
Answer Match 60.9%

Hi

I suspect this might be a fairly common problem. Whenever I print there also seems to be a block of about 5 fine lines printed over the text for about ever new line of text. Now I recently bought a new (high capacity) cartridge which costs a fortune, so I'm not too keen to buy another if it is the printer (about 6 years old) which is the problem.

Has anyone else had the same sort of problem?
 

A:Solved: Lines through printed page

Try cleaning the print heads, this is the normal solution to this problem.
 

2 more replies
Answer Match 60.48%

Three days ago when I tried to print from the web and then WORD there was no installed printer. I checked and the printer was still installed but when printing a document the print screen said their was no printer installed. I checked and the print spooler was not working. So I downloaded the Microsoft tool MicrosoftFixit.Printing.Run.exe. I ran it and presto the printer worked but only once and when I went to print again, again the print box showed that there was no printer installed. So I have to run the Microsoft.Fixit.printing.run.exe tool every time I want to print a page then restart the computer. A royal pain and time waster.

Something is turning the spooler off and not allowing individual programs to see the installed printer and therefore reports that there is no installed printer.

2nd issue. this is a new laptop (ACER) and there is no LED light to show "Caps Lock". I did find a setting that flashes the screen and makes an audible beep. However, my wife has the exact same computer and hers has a 2" x 2" box appear each time she puts cap Lock on. Which is way less distracting than audible beeps and flashing screens. Is there a setting for this? I have not found one in the Microsoft website for Windows 7.

Help,
yarlac

A:Print Spooler turns off after each printed page

Stop the print spooler servicePress Windows+R key and copy this path%WINDIR%\system32\spool\printersclick okDelete the files in the folderRestart the PC and try to print nowFor second issueDid you install ACER launch manager? It is responsible for caps lock notifications

5 more replies
Answer Match 60.48%

When I print I am getting a blank page between each printed page. Even if my document is one page it prints a blank page after it. I can also print a selected page, as in "print page 2" but it still prints a blank after it. The blank page does not show up on the preview.

I have a HP Deskjet D1300 and am running Vista Home using Word 2007. Is it a printer problem or a Word 2007 problem? Any suggestions?
 

A:Getting un-wanted blank page between printed pages

I think you may have the printer set to print separator pages.

Look around in your printer properties (Control Panel>Printers>Printername>>Right Click>Properties) and disable.
 

1 more replies
Answer Match 60.48%

is it possible to print both sides of a page without manually putting the page thru twice?  Or is a duplexer required to be added to the printer.

More replies
Answer Match 60.48%

I use two printers at two locations w/different computers and have the same problem on both. Many (most?) web pages have info on left side of screen that I do not want to print (such as at this web site). When I print the page I get the left side panel and letters or words on the right are cut off which I need to fill in by hand. Some sites offer "printable view", but I don't recall having a problem with that. Probably not.
Is there a way to adjust the page so that all desired text is printed?
 

A:printed text cropped off at R side of page

9 more replies
Answer Match 60.06%

When i try to print something the documents appear in my print queue then are deleted before they even begin to print, my printer was working fine until yesterday and now this

Please help

Steve
 

A:Printer deletes documents before they are printed

G'day steviejay, sounds like you have an intelligent printer that is censoring your output!
That is a worry, I haven't seen that problem previously.
You might try having a look in your control panel, system, devices or device manager, with a bit of luck when you scroll down through all your devices you will find a USB printer, (assuming yours is usb) if you open that item you should see something like "this devise is working properly" which is a good start for troubleshooting.
There should be no yellow exclamation marks on this item.
Are you quite sure your print queue in the print manager is being actually deleted?
What kind of printer is it?
The assumption is that it is a PC using a windows variant.
Cheers, qldit.
 

1 more replies
Answer Match 59.64%

I created a simple two column daily schedule for work. when I printed it, there were crooked triangles that appeared...yet they were not seen on my work before printing. There are 4 of them.
Any ideas how to get rid of them? thanks!
 

More replies
Answer Match 59.64%

I have a HP C4850 configured to work through the wireless. I can ping the printer and access its internal web page. Network configuration prints out no fails or errors so as far as I can tell everything is configured correctly. If I send it a print job, a small notepad document with the text "test" in it, it won't print. Eventually it just seems to forget the print job is there. However if I send the job, then print the network device configuration, the print job will print immediately after. I did this 3 times and it was consistent in its behavior. I'm at a complete loss, any ideas?
 

A:HP C4850 won't print until network status page is printed

Any ideas of where to start?
 

1 more replies
Answer Match 59.64%

hi my name is Sam i have had a printer brought me from parents all time i have had it has never printed. ink miss prints and bad quality i have read reviews which sound very positive but why is mine really bad

A:kodak all in one printer has nerver printed correctly

Did it ever print ok? Have you tried cleaning the print heads - there should be feature in the printer properties or Kodak monitor program to let you do this. Clogged heads are most common cause of bad quality printing. If it doesn't improve after several cleans, then best throw it away - printers are cheap, repairs are not.

3 more replies
Answer Match 59.64%

Hi, one of my clients is using the Epson ex 330 dot matrix printer on a windows xp sp 2 machine. Now this printer stopped working on this machine since the 24 pin port on the motherboard got spoilt. So I tried to connect this printer to this machine using a USB to parallel port converter. Now the thing is that the printer is added but when I try to give a test page print or any other print the print spooler shows 1 doument printing. But within 3 seconds it disappears and prints nothing with no error message. Another thing is that this printer used to run on the Epson LX 800 driver since there is no EX 300 driver is the default drivers list. And now I have added it on the same i.e LX 800 driver. But I don't think this should be any sort of problem. Expert help is appreciated. Thanks!!
 

More replies
Answer Match 59.22%

I have graphics that I would like to print, but the address, date & time are printed on the page. Is there a printer setting that would remove those?
Many thanks!
 

A:Solved: Remove address,date & time from printed page ??

10 more replies
Answer Match 59.22%

Hello everyone

I recently installed Outlook 2010 and I have got the following strange problem and I was wondering
whether anyone else had the same problem and found a solution.

Whenever I print an Outlook email, the pages come out in reverse order (page 2 then page 1) with a blank cover page which sometimes has "Microsoft Outlook - memo style OUTLOOK.EXE" printed
on the middle of it, and a blank sheet between each page of the message.

It only happens with Outlook. Printing is normal with Word, Excel, etc.

Any suggestions, please?

A:Outlook 2010 emails being printed with blank pages between each page

In Outlook please go to File - Print, highlight Memo Style, then click Print Options button above. In a new window Print, hightlight Memo Style again. Click Define Styles... In a new window, make sure that Memo Style is hightlighted and click RESET button.

If this wont help, click Edit button in the same window, and make sure all the parameters make sense and are correct (page size, etc.)

3 more replies
Answer Match 58.8%

I have an Access database used on daily basis to enter and print the maintenance work order in a report format. I have assigned a command button to print the required record. On clicking the button in the Form, a parameter query will run asking the user to put the record number to proceed. Once the correct record number is entered in the parameter text box, the report is previewed and the user click on the print button to print the same.

My question is as follows:

Is there any method to find out the record i am going to print now was already printed before? A kind of record keeping for the printed records.

Also, a message box should warn the user saying incase if the record was already printed, “The record was previously printed, do you want to continue printing again?”

Please tell me a way to perform the above in my Form.
Thanks,
Hash
 

A:Record keeping of the printed records & warning user when printed more than one time

could't you just add a field in the record for printed?

Then if printeed true, show warning, else show printable form.
 

2 more replies
Answer Match 58.8%

I am accessing an HP Laserjet 4650 via network and everything works great except for when I try to print out 2 or more copies of a 36-page PowerPoint presentation. I have both checked and unchecked the Collate box when I'm about to print, but neither seems to actually collate the printouts; it always prints out pages like 1, 1, 2, 2, 3... etc.

Any insight on this would be greatly appreciated.
 

A:HP4650 LJ Printer - Will not collate printed PowerPoint slides...

I tried the same in other programs, and no matter which program I print from, it neglects to collate the pages, whether or not I select Collate or not.
 

1 more replies
Answer Match 53.76%

Hello Everyone,
I have tried searching and searching for this problem but nothing seems to come up with this particularly odd problem. I'm actually running 3rd party software hosted on an AS/400 system but from a Windows 7 32-bit computer. If I right-click the title-bar of the window and select print, the print dialog box comes up asking for the printer I want to use. I select one, then click "Print" and the following comes out on the page....
<See Sample.jpg> (Of course, that's not an actual page, it's a representation of what you'd see on the page, but it's accurate despite the fact that it's color. Anyway, the print screens come out light and don't scan in well.)
As you can see, the print dialog box is clearly visible on the page. This seems to randomly crop up only on Windows 7 boxes and once it starts, we seem to have no way to stop it.
HEEEEyyyUUULLPP!!!
Thanks,
 

More replies
Answer Match 52.5%

only getting half of a page . How do I get the whole page ??

A:half of a page ???

Put two halves together? Be more specific.

3 more replies
Answer Match 52.5%

each time I click off a page , there is still some of the page remaining . how can I fix that. thanks , windows 7 ie 8 HP laptop . Roz

A:only half a page

Try resetting IE8 - http://support.microsoft.com/kb/923737

Update video drivers.

Check temps - may be overheating - http://www.almico.com/sfdownload.php

Is Vista SP2 installed - http://sysnative.com/0x1/Vista_SP_Prepwork.html

How much RAM do you have?

Regards. . .

jcgriff2

`

3 more replies
Answer Match 52.5%

Everytime I go to a web site I only get half a page. What is the problem?

A:Half page only.

G'Day suzo46, and Welcome to BC !
 
In the top right hand corner of any web page there are three symbols   ...
 
-  which reduces the page to the taskbar
(two tv screens overlapping) which when clicked cause the page to fill the screen  (sorry I could not find the actual symbol )
x    which when clicked , closes the current page
 
Does this answer your question.....or are you having a download issue where only a portion of the page is downloaded...??

2 more replies
Answer Match 52.08%

I have IE 6.0 and WXP
An original web page opens full size but if I click on a URL in the body of the page, the new window opens at half size. I can't find any Internet Option to correct this so that these new pages open at full size. So each time I have to hit the Maximize button to get the full size page.
 

A:Half size web page in IE

9 more replies
Answer Match 51.66%

hai everyone...

could u guys help me...?....
i use the usb printer (canon pixma ip1700)...
my prob, that printer do the print jobs just in half way...
it did't finish the print jobs for file type of pdf and doc...
in half way of print the file, the paper just pause in the printer...
sometimes it print normally and somtimes the prob occur...

actually, what the prob and how to solve it?...

p/s...sori for my bad english...
 

A:printer do job in half way

Why don't you simply uninstall the printer driver and reinstall it? Do you have the CD that came with it?
 

2 more replies
Answer Match 51.24%

Dell Inspiron 5110 Win 7 64 Home
Canon Pixma iP100
Canon BU30 Bluetooth adapter

Printer added successfully as Bluetooth - status shows "Ready"
Bluetooth printing service running
Bluetooth Printing Support is displayed under Bluetooth Radios

Print MS Test Page or anything else and only top half of page prints then printer hangs until it times out

Bluetooth printing works normally from my other computer so I assume printer and dongle are working nominally

Spent 45 minutes with Canon support to no avail.

Any help would be greatly appreciated

John

A:Bluetooth prints only half page

Does the page print fully using WIFI or a USB cable? Have you tried that to rule out a bluetooth issue?

5 more replies
Answer Match 51.24%

out the blue when i click on a new web site it comes up half the size on the screen yahoo comes up full size tech guy full size. some full some half. running windows xp home edition need help
 

A:size of web page shrunk to half

7 more replies
Answer Match 51.24%

This just started today. It's driving me nuts. When I click on link here or other places which will open up a new window, the page opens up to fill the top half of the screen. It does NOT happen if the link opens in the same window, because the page is already full size.If I click a link in my email, whether web based mail or Windows Live Mail, the page opens half screen.Opening up IE from the icon next to the Start menu opens full size.Using the desktop icon, sometimes full size, sometimes half size. I've done this several times, didn't work: Drag the corners of the window until it completely fills the screen. Hold down the Ctrl key, and while holding it down used the mouse to click File and then Exit on the toolbar.I tried it using the Shift key.Had this problem once on my XP system, dragging the corners, File/Exit did work on that one. No changes have been made to the computer. No new programs installed. Malware and virus scans have found nothing. It doesn't do it in SeaMonkey. I went to my daughter's desktop, and it does do it when clicking the IE icon next to the Start Menu. Screenshot of how it looks:All suggestions, advice, and clues on how to resolve this annoying thing will be much appreciated.

A:Page Opening Only On Half Screen

One of the features of Windows 7 is its areo snap. It can split either vertically or horizontally.I'm not sure if this is what you are experiencing, but this article explains how to disable it.

6 more replies
Answer Match 50.82%

Suddenly, whenever I open a new link - the page is only opening up in a half-size instead of as a new full page. What can I do to correct this ?

A:Links are only opening as a half page size.

i think the computer remembers the size of the last closed window, you can just hit "restore" (the button next to the "x" in the top right corner) then close it, i think then all windows of that program will open in full size.... or at least that is how it works for me (vista, IE 8)

1 more replies
Answer Match 50.82%

I KNOW it can be done. They did it here: Solved: Automatic information saver - Page 3 - Tech Support Guy Forums

However, I cannot get this to work. And it is exactly what I am trying to do: copy muzak playlists to notepad every half hour.

I have no way of contacting the person because of restrictions on the thread and I am not allowed to PM.

Can anyone help?

A:Automatically Save a Web Page every half hour?

Did you read through the entire thred, starting on page 1? All the info is in there, including download and install of AutoHotKey.

If it were me though, I'd use Wget and a batch file to read the web pages every so often. Wget is extreamly powerful and will take some time to learn but you can do amazing things with it.

3 more replies
Answer Match 50.82%

hello all i go to CBS everyday, to watch my game show since its on during the day, i keep the window small as i am doing other stuff and all of a sudden half of the page is white, but when i have the window fully maximized its fine how can i fix this

A:half page white on a webpage in chrome

Did you try another browser.

2 more replies
Answer Match 50.82%

When I go to Amazon the pages are loading only half a page. Amazon says its my problem . What is wrong ? Can it be fixed ? I have windows XP, DSL , IE broswer. thank you .

A:[SOLVED] Pages only loading half a page ???

Does this happen with other browsers like Firefox? What version of IE are you using? If it is older, upgrade to at least version 7. What kind of internet connection do you have? Is this a problem with every website or only some? What happens when you go to www.google.com, for instance?

3 more replies
Answer Match 50.4%

I have a HP 750ncomputer, my mouse S/N:LZE14570347. First noticed when scrolling on e-bay, that one side of the page scrolls slower than the other half. Checked the internet,it does the same. mauie
 

A:When scrolling, oneside of page scrolls faster than the other half.

Hiya and welcome

Lets do a 'spring clean' first:

Go to Tools | Internet Options. General tab. Under Delete Files, delete offline content. Also, clear the History.

Content tab, under AutoComplete, clear Forms and Passwords.

Advanced tab, under Browsing, look for Enable Insta on Demand. Untick.
Under Security, look for Empty Tempory Internet... Tick.
Apply and OK

Go to Run and type MSINFO32
On the left choose Software Enviroment, then Startup Programs. Copy/paste the list here.

Download Spybot - Search & Destroy from http://security.kolla.de

After installing, first press Online, and search for, put a check mark at, and install all updates.
Next, close all Internet Explorer and OE windows, hit 'Check for Problems', and have SpyBot remove all it finds.

Then, Go here for the free Ad-aware 6 Personal Build 181: http://www.lavasoft.de/support/download/

Then please launch the program ... on the start-up screen, you will need to first run the Webupdate Feature (globe at the top), or click "check for updates" on the start screen to get the Reference File up to date.

Please use either the Custom Scan with Memory and Both registry scans ON. Also.... make sure that you activate IN-DEPTH scanning.

Then, see that you have these options checked:
Under Ad-aware 6 Settings, Tweaks, Scanning Engine:
"Unload recognized processes during scanning."
Under Ad-aware 6 Settings, Tweaks, Cleaning Engine:
"Automatically try to ... Read more

1 more replies
Answer Match 50.4%

I'm doing some thread cycling, new questions for all you nice people out there.

Whenever I open my laptop back up, and hit the power button, it takes about 60 seconds to reach the password page. Once I type in my password, my computer hangs for about 2 minutes.

I had a Vaio VGN-NW265D laptop, with a bluray drive. I've used my bluray drive a handful of times within the last 1.5 years, and I'd rather have the performance. How would I go about putting in a SSD and installing windows 7 on that? I'm somewhat new to mods, but I'm affluent with computers.

A:Taskbar takes up half my page (autohide right side)

Rightclick in the taskbar and make sure "Lock the taskbar" isn't selected.
Now go to the borderline between desktop and taskbar until that little Arrow left/right appears.
Hold down the left mouse button and pull the task bar back to the size you desire.
Rightclick the taskbar and select "Lock the Taskbar"

-DG

9 more replies
Answer Match 50.4%

Hello. This is an odd one. On my office computer Firefox will freeze and not respond. After forcing it to close when I reopen it only a portion of a blank page appears. My office IT are preoccupied with more critical matters. Any ideas on what could be wrong? Thanks.

More replies
Answer Match 50.4%

page number is half visible office 2003? any experience in this issue from you guys? just got stuck to this problem today.. i have a know how to fix not visible page numbers but really had trouble with this "page number half visible office 2003"?

A:page number half visible office 2003

Hi Jaen,

Welcome back!

Double click on the footer and drag the line up to increase the size, this should allow the page number to display correctly!

3 more replies
Answer Match 49.98%

I have a Dell All in One printer Model 924, using in Windows 7. It worked fine until I changed the black ink cartridge. I used a refiiled one, which I suspect may be what is causing my problem. My problem is that it printed the test page fine, and now when I go to print anything at all in black it has the message that ink is low and do I want to use the option of using the color cartridge to print the black. I say "no" to print from the black cartridge. It just prints another test page and refuses to print the document it was supposed to do. The test page prints fine. No where in the manual does it give any information on the problem I am having. Does anyone have any idea what is going on?? I have used refilled cartridges before with no problem.
 

A:Solved: Nothing beyond test page

Have a look here & see if it solves your prob.

http://en.community.dell.com/suppor...article-on-refilling-dell-ink-cartridges.aspx

And maybe: http://en.community.dell.com/dell-groups/new-to-community/f/3511/p/19300811/19575253.aspx
 

3 more replies
Answer Match 49.98%

Hi all,

I am a newbie to this forum and I have looked at previous posts but it doesn't seem as though my particular problem has been answered as of yet...

Basically, I am running XP and have just installed a Netgear Wireless internet card as well as AVG Free 8.5.

All of a sudden last night I got a pop-up message out of the bottom right corner saying "Security Center Alert - You have a virus" or words to that effect... I click on it and get a IE window saying "Apache 2 Test page...powered by Centos". Then some stuff about the web domain and owner etc etc.

When I try to exit the window I get an error message saying my computer is infected with a virus and it won't let me close the window...It eventually closes itself a little while later, only to pop back up a couple minutes later. This is all accompanied by a little red X in the bottom corner of the tray...

So, I'm after some help really. I've googled around and found some references to the computer being hijacked? When I read that I turned off my router...

Can anyone help with this and tell me what I need to do??

PS - I should add, I found this website as I am having a problem with fast user switching and the mrvgina.dll (from Netgear) disabling it. I am working through fixing that too...just thought I should mention it in case it might be related??

Thank you all very very much in advance!!

A:Apache 2 Test Page

Hello and welcome to TSF.

We want all our members to perform the steps outlined in the link given below, before posting for assistance. There's a sticky at the top of this forum, and a
Quote:




Having problems with spyware and pop-ups? First Steps




link at the top of each page.

Please follow our pre-posting process outlined here:

http://www.techsupportforum.com/f50/...lp-305963.html

After running through all the steps, you shall have a proper set of logs. Please post them in a new topic, as this one shall be closed.

If you have trouble with one of the steps, simply move on to the next one, and make note of it in your reply.

1 more replies
Answer Match 49.98%

I have a HP LaserJet 1200.
Every time I turn the printer on, it prints a test page.
This creates a lot of wasted paper and toner.
How can I stop the printer from printing this test page???
 

A:Test Page Problem

There should be a setting somewhere in the printer settings to stop that from happening.
 

1 more replies
Answer Match 49.98%

Hello,

I am trying to make all of my machines to talk to each other (On my home network) as well as share a printer on one machine (wired via USB). I am running Windows 10 Pro on the machine with the printer.

The other machines are running Windows 7 Pro. All machines are are part of the Workgroup called Workgroup. Also I have Uverse as my Internet/Router (NVG599).

Currently all machines see all folders and the printer. The problem is I am unable to access files or drives. For example one of my machines is "Office (Windows 7 Pro)" and my other is "Studio (Windows 10 pro)".
"Studio" is set to Private Network , and all other machine are set as Public. All machines can use the printer on "Studio" which is hooked up via USB.

When I am at my computer "Studio" and try to access files on "Office" I get the following; "Windows is unable to access \\Office-PC\Documents" (Documents being the shared folder, with full access privileges). This example applies to these machine an all others I have at home; printer share works (I can print from all of my computers) but file/drive share does not


Any and all help welcome very much.

Thank You,
RH

A:Printer and File Sharing... half works. Please help.

Hi can you use your printer via WI-FI as that is how I have mine set up and all other OS including smart phones can access it and use it.

1 more replies
Answer Match 49.98%

I'm having some issues with a dot matrix printer when printing through a DOS based application. When trying to print through the DOS based application the printer starts printing and then suddenly stops half way through and does not give any kind of error message. Another thin is that when printing through this application it starts printing in condensed mode and then goes haywire. Dunno what the problem could be. But it prints fine through MS office and other applications.
Any help is appreciated. thanks
 

A:DOT matrix printer stops printing half way

which model? i believe the panasonic models have dip switches on the back
for windows / dos applications. also disable ecc in bios and might help it work in dos
 

2 more replies
Answer Match 49.98%

I'm running Windows 98 with Office 2000. One of my powerpoint files appears to be demon-possessed. Most of it will print normally, one slide (which appears in modified form 4 times in the 30 total slides) prints differently each time. It contains several shapes inside shapes (pentagons inside a circle). The pentagons come out of the printer totally black! The crazy part is that of the 8 pentagons, a different combination is blacked out each time I print. Sometimes, the top two, sometimes the side three, sometimes the bottom four. It prints erratically in the handouts (six to a page) style too. Every other slide in the file, however, prints totally normally.
Help?
 

A:printer prints one slide half blacked out

Since all else is well with the printer, this has to be a software issue.

I am moving this to the Applications forum where, hopefully, someone who knows about PowerPoint can help you.
 

1 more replies
Answer Match 49.98%

I'm running Windows 98 with Office 2000. One of my powerpoint files appears to be demon-possessed. Most of it will print normally, one slide (which appears in modified form 4 times in the 30 total slides) prints differently each time. It contains several shapes inside shapes (pentagons inside a circle). The pentagons come out of the printer totally black! The crazy part is that of the 8 pentagons, a different combination is blacked out each time I print. Sometimes, the top two, sometimes the side three, sometimes the bottom four. It prints erratically in the handouts (six to a page) style too. Every other slide in the file, however, prints totally normally.
Help?
 

A:printer prints one slide half blacked out

Since all else is well with the printer, this has to be a software issue.

I am moving this to the Applications forum where, hopefully, someone who knows about PowerPoint can help you.
 

1 more replies
Answer Match 49.98%

Hi
My printer stops printing when I am half way through a print job. I tried turning it off and back on to clear some cache but still no luck.

Windows XP; 256 MB RAM

Could this be a memory problem?

SR
 

A:Printer stops printing half way through a print job

7 more replies
Answer Match 49.98%

Hi,I noticed this morning that none of the web pages where getting downloaded fully in the browser. I have ran superAntiSpyware to find a fix the issues but i'm not convienced that it worked. Heres the HJT log. Would really appreciate if someone can have a look and suggest how to fix the issues.Many ThanksLogfile of Trend Micro HijackThis v2.0.4Scan saved at 14:53:09, on 28/06/2010Platform: Windows XP SP3 (WinNT 5.01.2600)MSIE: Internet Explorer v8.00 (8.00.6001.18702)Boot mode: NormalRunning processes:C:\windows\System32\smss.exeC:\windows\system32\winlogon.exeC:\windows\system32\services.exeC:\windows\system32\lsass.exeC:\WINDOWS\system32\nvsvc32.exeC:\windows\system32\svchost.exeC:\Program Files\Trusteer\Rapport\bin\RapportMgmtService.exeC:\windows\System32\svchost.exeC:\Program Files\Ahead\InCD\InCDsrv.exeC:\windows\system32\svchost.exeC:\windows\system32\spoolsv.exeC:\Program Files\Common Files\Apple\Mobile Device Support\AppleMobileDeviceService.exeC:\Program Files\Bonjour\mDNSResponder.exeC:\Program Files\ESET\ESET NOD32 Antivirus\ekrn.exeC:\Program Files\Intel\Intel Matrix Storage Manager\iaantmon.exeC:\Program Files\Java\jre6\bin\jqs.exeC:\Program Files\Marvell\61xx�... Read more

A:PC running very slow and browsers stops download page half way

Hello and welcome to Bleeping ComputerWe apologize for the delay in responding to your request for help. Here at Bleeping Computer we get overwhelmed at times, and we are trying our best to keep up. Please note that your topic was not intentionally overlooked. Our mission is to help everyone in need, but sometimes it takes just a little longer to get to every request for help. No one is ignored here.If you have since resolved the original problem you were having, we would appreciate you letting us know. If not please perform the following steps below so we can have a look at the current condition of your machine. If you have not done so, include a clear description of the problems you're having, along with any steps you may have performed so far.Upon completing the steps below another staff member will review and take the steps necessary with you to get your machine back in working order clean and free of malware.If you have already posted a DDS log, please do so again, as your situation may have changed.Use the 'Add Reply' and add the new log to this thread.Thanks and again sorry for the delay.We need to see some information about what is happening in your machine. Please perform the following scan:Download DDS by sUBs from one of the following links. Save it to your desktop.DDS.scrDDS.pifDouble click on the DDS icon, allow it to run.A small box will open, with an explaination about the tool. No input is needed, the scan is running.Notepad will open with the results.Foll... Read more

2 more replies
Answer Match 49.56%

...view the print troubleshooter for assistance? Operation could not be completed.

This is the error message that I've been getting. This is a WORKING network printer. Other people can print to it.

My specs:
Dell GX270 (P-4 2.8GHz)
512 DDR RAM
Windows XP with ALL the updates (Not SP2, though)
Trying to print to a WORKING network printer.

Whats been done so far:
The printer is ONLINE
I have reinstalled the Printer on my PC. No luck.
 

A:Test page failed to print. Would you like to....

Howdy aerain...

Just a few questions...

What type of printer is it?

If it is a true Network printer ( not one that is shared out from another work station ), try opening a command prompt an see if you can ping it...

Also try, uninstalling the printer ( if you can ping it ), then go to C:\WINDOWS\system32\spool, and delete all the drivers/files associated to that printer ( sometimes during the uninstall these don't get deleted ), check all the folders that are in the Spool folder for the drivers/files...
 

1 more replies
Answer Match 49.56%

One of our windows 7 has a print problem. Whenever I send a test print page, it says

"Test Page failed to print". I have tried these
1. Uninstall and reinstall the printer drive.
2. Restart printer spooler service and computer.
3. Try different user account including administrator account.
4. Turn off and then turn on the printer.
5. Try to add different printers such as HP, canon and Lexmark. All have the same problem.
Any suggestions?

Bob Lin, MCSE & CNE Networking, Internet, Routing, VPN Networking, Internet, Routing, VPN Troubleshooting on http://www.ChicagoTech.net How to Install and Configure Windows, VMware, Virtualization and Cisco on http://www.HowToNetworking.com

More replies
Answer Match 49.56%

I am trying to create a shortcut on the desktop for print test page.
I have tried a couple of different googled solutions and cannot find one that works...
First I tried - 
cscript C:\Windows\System32\Printing_Admin_Scripts\en-US\prnqctl.vbs -e -p "Brother PJ-622"


I tried this from both a normal and elevated command prompt - logged in user is a local admin - both resulted in 
Failed Print Test Page Win32 error code 5

I tried the same command using a -u and -w command to specify the local admin account.  This didnt work either and  
I also tried 
print /d:printer textpage.txt
just to get something to print... this didnt work..



Ok I had all this typed out and found a powershell solution that works so I am going to go ahead and post this anyways for anyone else to use.  There was alot of ways with powershell 4 using invoke but i found a simpler way with a couple lines to print
to default printer.  This works on powershell version 2.

Create PrintTestPage.ps1 in notepad and save as ps1 file...

$printer = Get-WmiObject -Query " SELECT * FROM Win32_Printer WHERE Default=$true"
$PrintTestPage = $printer.PrintTestPage()  




Edit - obviously for the shortcut I just modified the target to the path of the script.

%SystemRoot%\system32\WindowsPowerShell\v1.0\powershell.exe -ExecutionPolicy Bypass -File C:\MDT\Powershell\PrintTestPage.ps1

A:Print Test Page Shortcut

AFAICS the VBScript you used no longer works under Windows 7 even though it is still included. Howerver, this command does work:
rundll32 printui.dll,PrintUIEntry /k /n "\\%ComputerName%\SharedPrinterName"

5 more replies
Answer Match 49.56%

Try to print from my documents. Printer window opens says its printing lasts about 5 sec then says printing complete. Tried making a new document same thing. Open window thru start menu click test page and it prints that.
What's up with this? was working fine earlier.
 

A:Ij600 only prints test page

But what software program are you "printing from" when it fails to work?
 

1 more replies
Answer Match 49.56%

Hi,  My printers connection states Idel as the staus and will not connect to my mac wich is currently running macOS Sierra 10.12.1.  My printer will only print from my Mac when I email it or connect directly to the printers wifi, which means I cannot use other internet programms while im connected.  My printer is a hp Envy 4520 All-in-on printer.  Thanks Ellie. 

More replies
Answer Match 49.56%

I have a windows 7 machine that I can print a test page and print from notepad normally, but the machine will not print anything from other applications such as word or excel. I monitor the print que, and the test page shows up, but when I print something from word nothing comes up.

I have deleted the printer, remove the print drivers, install a totally differenet printer and have the same issue. I have tried to print from differenet user profiles with the same issues. The printers work great on other computers.

This is happening to both local printers and network printers. The printers are recognized and test prints works fine.


Any ideas?

A:Can not print anything except from notepad or test page

Some things to try:

Stop and restart the print spooler service

Services - Start or Disable

Scroll down to Print Spooler. It should be started and set to automatic. If it is, stop the service and restart it and try to print.

Start> In search box type Devices and printers> Enter> Confirm your printer is set to default, and not the Microsoft XPS Document writer

If not, right click the printer and choose Set as default printer

Start> All programs> Administrative tools> Computer management> Device manager> Expand printers and look for yellow exclamation marks

Start> In search box type troubleshooting> Enter> Under Hardware and Sound> Use a printer> When the troubleshooter opens, click on next and follow instructions

A Guy

1 more replies
Answer Match 49.56%

I have a desktop with xp pro and a lexmark c530dn that i am trying to connect locally. The driver installs, but i can't print a test page, much less anything else. The documents just stack up in the queue, and i get a message that says "this document failed to print." I've deleted and re-downloaded the driver several times, tried turning off the firewall, and replaced the cable. The printer will print the settings from its menu. I've hit the bonk. Please help.
 

A:lexmark won't connect - no test page

It was the port setting.
 

1 more replies
Answer Match 49.56%

Hi, I'm new in this forum and I really don't know where I should put this and I tried searching the forums via the Oh-so-helpful search button, but no luck. I'm getting this camera and printer icon popping up on my taskbar which causes games to minimize. At first I didn't know what that icon was, so I tried scanning my computer with MSE and found nothing. So I tried to screenshot the thing and got a decent screenie. I also found out that it pops up every minute, and it only appears for about half a second. Any tips on how to remove this and what caused this problem? Thanks.


Here's the screenie I took:



Thanks in advance guys.

A:Camera and Printer Icon, pops up for half a second and disappears

Camera and Printer Icon, pops up for half a second and disappears - Google Search
Google has plenty of info,Hope it helps you out.Good luck.

9 more replies
Answer Match 49.14%

What is the best way to test a printers quality.

I have an Epson Stylus Photo R300 and I am trying to test it before and after I do a load of maintinance on it to see if it makes much difference.

Any Help apreciated

thanks Jack-O-Bytes.
 

A:Solved: Best printer test?

Print a picture that has all the primary colors.
 

3 more replies
Answer Match 49.14%

i own a xerox workcenter 450c, which is an all in one (fax,printer, scanner, etc) My problem is i don't use it as a fax machine so i don't keep it plugged into a phone jack. However, the printer prints a test report each time i turn it on telling me that there is no dial tone--how can i make it so it doesn't do this?
 

A:Printer Test Reports

Being an ex-salesman at Staples - the Business Depot I would instruct you to call the Xerox. You can also go through the function setup and turn it off in there but I do not recall how. It's been a long time.

Cheers
Macky
-----------------------
"AArgh" - (Ten Thirteen Productions)
 

1 more replies
Answer Match 49.14%

So I just got this random idea and checked google but found nothing. Can the image that prints on the printer test page be changed, and if so, how?

I'm on windows 7 64 bit

[edit]

Ok, people don't seem to get my point. You know the page that comes out with the windows logo image and a list of the drivers being used on it when you click print test page from printer properties in windows? That's the one I want to change.

A:Changing the print test page image

After using the print test on a HP many years ago I now just print a small text file to see it the printing is OK.

The HP print test printed out a FULL page coloured print. Never again.

Doesn't help you but I had to say something.

2 more replies
Answer Match 49.14%

I posted a similar thread the other day, but I am now doing it properly with attachments etc

*****************************************************

I have just installed a Netgear Wireless internet card as well as Sky Broadband and that's when my problems started!

Following that I installed AVG Free 8.5...

First of all, I've been getting a pop-up message out of the bottom right corner saying "Security Center Alert - You have a virus" or words to that effect... I click on it and get a IE window saying "Apache 2 Test page...powered by Centos". Then some stuff about the web domain and owner etc etc.

When I try to exit the window I get an error message saying my computer is infected with a virus and it won't let me close the window...It eventually closes itself a little while later, only to pop back up a couple minutes later. This is all accompanied by a little red X in the bottom corner of the tray...

I've googled around and found some references to the computer being hijacked? When I read that I turned off my router...

Secondly, my computer takes a good 5 minutes to start up and actually be ready to use. If I try and open something before it's completely finished loading (even if all the icons have appeared and it looks ready to go) then it runs incredibly slowly...

So, both of these problems have occured since I installed Netgear and the Sky Broadband software. Any help that someone maybe might be able to give me would be AMAZING!
... Read more

A:Apache 2 test page and sloooow start up

Hi,

Please do the following:

Download ComboFix from one of the following locations:
Link 1
Link 2

VERY IMPORTANT !!! Save ComboFix.exe to your Desktop

* IMPORTANT - Disable your AntiVirus and AntiSpyware applications, usually via a right click on the System Tray icon. They may otherwise interfere with our tools. If you have difficulty properly disabling your protective programs, refer to this link here Double click on ComboFix.exe & follow the prompts.
As part of it's process, ComboFix will check to see if the Microsoft Windows Recovery Console is installed. With malware infections being as they are today, it's strongly recommended to have this pre-installed on your machine before doing any malware removal. It will allow you to boot up into a special recovery/repair mode that will allow us to more easily help you should your computer have a problem after an attempted removal of malware.
Follow the prompts to allow ComboFix to download and install the Microsoft Windows Recovery Console, and when prompted, agree to the End-User License Agreement to install the Microsoft Windows Recovery Console.
**Please note: If the Microsoft Windows Recovery Console is already installed, ComboFix will continue it's malware removal procedures.


Once the Microsoft Windows Recovery Console is installed using ComboFix, you should see the following message:


Click on Yes, to continue scanning for malware.
When finished, it sh... Read more

13 more replies
Answer Match 49.14%

I am having the hardest time finding a code that works.... please help i have been searching for days ... my level is novice

thank you

A:printing a test page from the command prompt

Specifically, what are you trying to do?

3 more replies
Answer Match 49.14%

I've got a stubborn infection that just won't go away. I've installed and run ADWCleaner, MalwareBytes, Spybot, rkill and Windows Defender. The infection did used to be worse w/ popups for fake tech support and such. I've eliminated most of it. However, throughout the course of the day, IE will randomly open and load the aforementioned page. IE won't load the page as it's deemed to be unsafe, but it just keeps happening. I must be missing something.
 
Here is the popup that keeps happening:
https://www.dropbox.com/s/aivnee0gue24qwk/screenshot.png?dl=0
 
Logs:
 
Scan result of Farbar Recovery Scan Tool (FRST) (x64) Version: 21-09-2016
Ran by foxte (administrator) on DESKTOP-SLRRCRP (23-09-2016 00:00:22)
Running from C:\Users\foxte\Downloads
Loaded Profiles: foxte &  (Available Profiles: foxte)
Platform: Windows 10 Home Version 1511 (X64) Language: English (United States)
Internet Explorer Version 11 (Default browser: Edge)
Boot Mode: Normal
Tutorial for Farbar Recovery Scan Tool: http://www.geekstogo.com/forum/topic/335081-frst-tutorial-how-to-use-farbar-recovery-scan-tool/
 
==================== Processes (Whitelisted) =================
 
(If an entry is included in the fixlist, the process will be closed. The file will not be moved.)
 
(IObit) C:\Program Files (x86)\IObit\Advanced SystemCare\ASCService.exe
(Intel Corporation) C:\Windows\System32\igfxCUIService.exe
(Intel Corporation) C:\Windows\SysWOW64\IntelCpHeciSvc.exe
(Hewlett-Packa... Read more

More replies
Answer Match 48.3%

hi everyone i cant print fom word 2007,wordpad and even a windows test page.i have a hp 125nw mfp configured as wireless.it was working fine but few days back when i try to print it doesnt print at all.i can only print via notepad.i have the latest drivers and i have a windows 7 home basic x64.the printer is working fine on other laptops and pcs running windows 8 and windows 7 with office 2007,2010 and 2013 around me in my office on the same printer and same wireless network.i have followed the steps here

More replies
Answer Match 48.3%

What is the usual diagnosis or outcome when an HP C6280 AIO won't print a correct Self Test Diagnostic from control panel? It printed it one (won't print another because of multiple errors); was missing ALL data from boxes & sections of 2 pg. report - except color print test boxes (looked fine). Just printed report sections headers & data boxes.

Gone through usual printer reset steps: power reset; clearing hardware error codes via "secret menu," then unplugging & waiting 60 sec.
That clears 1 (or more) errors, but they re-appear. The errors just rotate; clear 1, another pops.

Carriage or paper jam (neither true); carriage moves easily by hand - isn't "jammed" when reports it. Hitting OK starts carriage moving again.
No paper or bits. Took lid & top cover off. No paper bits that are visible - front, back, inside paper tray area, w/o dismantling entire unit.

Ink system failure: printed perfect text, lines & color boxes on the partial self test, after that error appeared & was cleared - several times;

Pump Motor Stalled: DON'T think ink motor is stalled or not working. Printed perfect lines, headings & color boxes on the one self test (lacking data). With top cover off, can see all pump gears, belt turning normally in warm up. Pump sounds normal during printer prep.

Paper pick up rollers NOT turning - that's true (except for ONE self test w/o the data). They turn easily by hand; not dirty - just don&#... Read more

A:HP printer not printing self test diagnostic; many errors

Seems toast to me. You've been pretty thorough.
 

2 more replies
Answer Match 48.3%

I installed a new cartridge in HP PSC 1510, and now it prints a Test Page before every print job. I have tried EVERYTHING to make it stop. Wastes lots of time and ink. Please, someone assist.
 

A:HP Printer won't stop printing Test Pages

7 more replies
Answer Match 47.88%

I have firefox v49 (portable version from portableapps.com) and when I choose print and select MS print to pdf, it goes through the motions but the file does not get created.

I can use the test print function with success and also it worked from edge and notepad. Could it be firefox (or my portable version) that is the issue?

Anyone else see this or any ideas how to get it to work with Firefox?

More replies
Answer Match 47.88%

Epson XP 400 - Test Page - Printing Color - Why? - How Do I Fix.

Hello, I was testing out some ink on my Epson XP-400 Printer.

http://www.epson.com/cgi-bin/Store/jsp/Product.do?sku=C11CC07201

Anyway, I had to clean ink head, even though I periodically do it anyway. Yes I know that it is recommended in the tech community. Then print test page, which came out fine. However, I accidentally left the color enable. So turned it off. Printed another test page. The color came out, you where the Windows Logo is on the corner.

Computer Specs: Lenovo V570 Windows 7.
 

A:Epson XP 400 - Test Page - Printing Color When Set to Black&White - How Fix?

Print Only in Black and White:
• Click Start > Settings > Printers and Faxes.
• Left click on Laser to highlight.
• Click File > Printing Preferences.
• Click on the Color tab.
• Click on the circle by Grayscale to move the bullet to that selection.
• Click Apply and OK.

to switch from "colour" printing to "black".

So, "unclick" the 'Grayscale' setting.
hope this helps.
 

2 more replies
Answer Match 47.88%

Which is the recommended location to maintain Product Regression Test Suite ? Would it be QC Test Plan or Test Lab ? (specially for applications that tend to change consistently over time which might require us to update core regression suite as well as functional test cases regularly)  

More replies
Answer Match 46.2%

I am printing a Microsoft Word 2007 document and the numbers are cut off at the bottom of the page. This is using an HP7100 inkjet. Part of the footer is lost as well.

When I change the printer, and print from our Canon ir2018 LASER, everything is printed in its entirety. There are no problems, and that's with me not altering the Word file whatsoever.

I am able to print an Excel spreadsheet using the HP7100 until about 1/4" of the bottom of the page. These page numbers in the Word 2007 are much higher up (physically) and should not be out of the range of the printer considering what it can do for the Excel file.

Lastly, when viewing the document in "Print Preview" in Word, if I have the HP7100 set to print, it does not show that the footer will be printed. If I change the Printer to the Canon, the footer returns. So Print Preview accurately tells me what will be printed based on which printer I select to print from.

Is this an issue in Microsoft Word? How can I print these footers and page numbers from my HP7100?

Chris
 

More replies
Answer Match 44.1%

Hello, entire 7F community,

I put this problem here because it relates not just to theme files, but is also about system files and/or advanced solutions. I know that this question (or at least its other variant) has been asked before, but I didn't manage to find the solution.

The problem is:
After failed boot with incompatible firewire card (tried WinXP drivers as legacy hardware driver, etc) I removed it and just to make sure that the PC would boot I've copied whole system32 from Win7 installation disk (X:\Windows) directly to original windir (C:\windows) using "xcopy /E /H /R /Y" thus attempting to fix somehow incorrect and not included in C:\windows IEEE 1394 driver in the process. The PC booted. But now I noticed that the taskbar was in classic style with aero top edge (see here) and any explorer window looks like this (notice the edges of the window and compare it to organize/system properties/etc bar).

Steps I have taken since then (in order):Ran chkdsk /f /r
Ran sfc /scannow
Done an in-place upgrade
Set visuals to maximum quality (best appearance)
Reinstalled GPU drivers
Restarted themes and uxsms many times (aero/basic themes become grey until reboot)
Ran Fixit troubleshooters

None of those helped.

I didn't set up system backup/recovery, so this option won't help me a bit.

A:Theme glitch: half aero, half classic

Hello Paulius5, and welcome to the SevenForums,

Please patch your system with Universal Theme Patcher by following step one to six of this tutorial and reboot afterwards.
If the Aero theme still resembles the Windows Classic theme, please report back to us.
Good luck and keep us posted,
Nommy

9 more replies
Answer Match 44.1%

Purchased a new Hitachi/LG Combination burner/dvd (player) installed with a second streight cd dom drive connected in master/slave config. The dvd side of the drive using Cyberlink PowerDVD installed and plays fine. But anything else, a data disc, music, installation of Nero 6.0 (recommended for the drive)
will not work. Does the cdrw side of the drive sound bad? (the second streight cd drive works fine and performs all function it should)-

The only other event during dvd install (done first) was an intial WMA
change when first installing the dvd software, but the change took and the reinstall indicated that the change was successful. I've done this on others combination drives before without creating any issues like this, so I either did something with the WMA change or it's a bad cdrw....would anyone care to speculate??? I would appreciate it! (if this is a bad drive, I can get it repaced).

FYI...uninstalled and reinstalled both the combination as well as the streight cd drive and both continued to function as before-

Many thanks in advance for the help-
Webz
 

A:New dvd/cdrw combo half works....half doesn't???

R E S O L V E D ! ! ! !
 

1 more replies
Answer Match 44.1%

My laptop has windows 10. When i power on my laptop often these days I see this screen comes up. After few seconds It starts beeping sound. I power off the laptop, then power it on again until the laptop boots up normally. Usually in two to three chances it boots up normally. After it boots up it doesn't give any problem it functions normally, its only when I power it on 70% of the time it shows this screen. It starts from the top and runs to the bottom those lines. What might be the problem ? I am using windows 10 on inspiron 15r SE 7250 I updated chipset and bios driver few week back and also changed the thermal paste on cpu and gpu

A:Half white and half black screen during booting

When this happens after a few seconds it gives Beep sound. I counted the beeps and it was total 8 times.
8 times beep then after a little pause it starts again. Does it means 8 beeps ie; LCD failure ? If yes then what should I do

1 more replies
Answer Match 43.68%

I am not a script writer. In fact, the last time I wrote a script it was by creating a .bat file to run on an old MS-DOS 5 machine. But I sure would appreciate help with instructions on setting up a printer script for the printers on my Vista home network.

I have four PC's, 3-Inkjets and 1-Laser printer on my network. To keep the inkjet ink cartridges from drying up from non-use, I'd like to setup a routine on one of the Vista PC's to automatically issue a "Print Test Page" command to each of the inkjet printers once every week. Can this be done, and if so, how?

Thanks in advance for your assiatance...

A:Help Creating Vista "Print Test Page" Script

Either I posted this at the wrong website/forum, or perhaps what I am trying to do cannot be done in Vista. Would appreciate some direction from an administrator or one of you scripting experts, please.

1 more replies
Answer Match 43.68%

When trying to browse the homepage of www.aami.com.au I'm getting redirected to http://www.aami.com.au/boost-gzip-cookie-test.html after seeing the homepage for 1 second.

I've read the other forum post (http://forums.techguy.org/web-email/959278-what-boost-gzip-cookie-test.html?highlight=boost) that says this is related to IE6 as an out of date browser but I'm using IE8

Others in my organisation can access the site OK on the same IE version. Can anyone help?

_____________________________________________________________________________________
Tech Support Guy System Info Utility version 1.0.0.2
OS Version: Microsoft Windows XP Professional, Service Pack 3, 32 bit
Processor: Intel Pentium II processor, x86 Family 6 Model 37 Stepping 5
Processor Count: 4
RAM: 2991 Mb
Graphics Card: ConfigMgr Remote Control Driver, 1024 Mb
Hard Drives: C: Total - 238472 MB, Free - 217093 MB;
Motherboard: Hewlett-Packard, 7008
Antivirus: Trend Micro OfficeScan Antivirus, Updated: Yes, On-Demand Scanner: Enabled
 

More replies
Answer Match 43.26%

I just formatted the hard drive and installed the OS. Downloaded the printer driver from Canon's website and installed it. I'm able to print a test page and align the printer heads, but when I try to print from any application, it comes back with this message:

"An error occurred during this operation"

I hit OK and then it closes. No print dialogue box.

Everything is fine in device manager.

Ideas?
 

A:Can print a test page, but can't print from any application; fresh system

In Control Panel, "Printers" is the Canon setup as the default printer?
 

2 more replies
Answer Match 43.26%

Today i booted up my computor and some updates were automatically done and then i had to restart. when i began working on my project again the function of assigning one pane to one side and the other half of the window. i am running a sony vaio and originally it had a thing at the top of the desktop screen, a toolbar i think. any way to get this function back?
all help appreciated.
cheers

A:half half windows function not working

i think this is what you are referring to: Aero Snap - Turn On or Off

2 more replies
Answer Match 43.26%

Hi All,

Trying to print out a newletter (in a book form) where i want the front and last pages in colour but the rest in b&w.

All images etc through out the entire document is in colour. Just wondering if you can possibly specify which pages to print in colour and which ones in b&w from within MS Publisher 2000, 2002 or 2003.

I cant do it from the print driver thus me asking if i can do it from within the application. Any thoughts would be great. thanks in advance.

Regards

Steve
 

A:Printing a Newsletter - Half in Colour and Half in B&W

7 more replies
Answer Match 43.26%

I have an annoying problem which occurs very infrequently. For some reason there are times when the scroll bar on the righthand side of my screen is at least half off the screen. How do I resize my screen so that the entire bar and the up and down arrows are back onscreen? I tried dragging, but that didn't work. I'm sure there has to be a very simple answer to this minor problem. Thank you.
 

A:Solved: Why is my right scroll bar half-on and half-off my screen?

Use the positioning and resizing controls on your monitor itself
 

2 more replies
Answer Match 43.26%

It confuses me so much... ._.

How do you reset it? I tried changing themes, that didn't really work...
Can someone... please... help...

A:Theme being half-aero half-classic.... uhh what

  
Quote: Originally Posted by Bonzomi


It confuses me so much... ._.

How do you reset it? I tried changing themes, that didn't really work...
Can someone... please... help...


That looks like you have it in Classic mode instead of Aero. Your Start button says "Start". Mine is round and does not say Start. == Right click on the desktop and then click "Personalize". Go into Themes and pick one that says "Aero". Let us know if that helps.

2 more replies
Answer Match 43.26%

Ok here is my issue; i had a health computer until a few days ago, we usually play World of Warcraft, and one of my friend took a break, and he is playing on some private server just to spend some free time of his. Anyway i was playing WoW on official server, then my friend came, i logged off, changed realmlist.wtf file to join the private server (cleared cache etc. so i am sure its not a game based issue) i created a character played a few minutes then logged off to disable an addon (here it starts) when i logged in, the milisecond i saw my character my computer froze. i am using a wireless logitech keyboard and a4 tech x7 mouse, when i press the numlock the numlock led on the receiver was working(its on ps2) but the led on my mouse was off, just like i unplugged it. restarted retried to join the private server, same thing happened...and again and again and again... i changed realmlist back to original and voila, i was able to play on official wow.

i thought it is something about the heat, and i expected it is caused by the gpu, downloaded some sensor softwares and everything but AUX was normal,it was changin about 65-80 C degrees.and the sensor which is sensing that "AUX" was on motherboard so i thought it is the "bridge-way" or whatever that called in english (the cooler right next to pci-e slot) and it was a bit loose when i touched it (it wasnt exactly loose but i could shake it easily by touching with a little force), opened my case, brought a huge ... Read more

A:Computer Freezes Half-Randomly Half-Not

i forgot to add system details and here is the motherboard picture;

Motherboard: Gibabyte S-Series GA-M56S-S3
RAM: 2x 2 GB Kingston DDR2 800 (Dual)
Processor: AMD Athlon(tm) 64 X2 Dual Core Processor 5000+ (2612 MHz)
Operating System: Windows 7 Ultimate, 64-bit
GPU processor: GeForce 9600 GT
GPU Driver version: 257.21
 

3 more replies
Answer Match 43.26%

Hi,
I use the photography website 500px.com, and recently for some reason part of it has translated itself into German (http://imgur.com/l8bxzs7) I recently started to use a VPN so that could be the issue. Any ideas? Thanks, Ron.

A:Half of website in German, other half in English

I recently started to use a VPN so that could be the issue.
That's quite possible.  Some websites automatically detect your language settings and adapt to suit.  Where is your VPN terminating?  Does the same thing happen when you visit the site without activating the VPN?

1 more replies
Answer Match 42.42%

My lexmark P4350 has worked for years and now for some reason today, after installing a new black ink cartridge it now refuses to print more than one page.

If you select to print a document (of say 4 pages) it will print the first page and then automatically stop for no reason and refuses to print any further pages of the document.

I am on Windows vista and have already tried uninstalling and reinstalling the printer. I use a USB to connect the printer to the computer.

Please help as I love this printer and am thoroughly fed up having to print one page at a time!!

Alex
 

A:Help Help...why will my printer only print one page!!

Does it work if you put the old cartridge back in?
 

2 more replies