Tech Problem Aggregator

Why BIOS does not recognize new HDD in Compaq Presario Computer?

Q: Why BIOS does not recognize new HDD in Compaq Presario Computer?

Hello! I'm new here to these forums hoping to find a solution to this problem that has been bugging me for days and keeping me from setting up my computer.

Basically after several years, I am finally dealing with the loss of my Hard-Disk drive that came with my computer. I have bought a new Samsung Spinpoint F3 HD502HJ as a replacement, and I am having trouble setting it up. Here are a few Specs for my computer:

Compaq Presario SR1303WM
AMD Sempron 3000+
BIOS Revision 3.11
Mother Board: ASUS A7V8X-LA

It's a bit of an older computer. The HDD that failed me used the old ATA standard, and I am going from that to SATA II (3 Gb/s). My motherboard does have two SATA ports on it, but I don't think the motherboard supports 3 Gb/s transfer rate. Only 1.5 Gb/s. I have an SATA cable that connects directly from the HDD to the MoBo as well as a power converter that I use to connect power to the new HDD. I am using a jumper on the fifth and sixth pins ::[:]: <--- looks like that. The reason I am using a jumper is because I have read by other people that this puts the device into the 1.5 Gb/s mode, although I'm not entirely sure. The Samsung manual my HDD came with says that in order to put the drive into this mode, you must download and use their software from their site, www.samsung.com/hdd which I have tried and failed. When I run Samsung's software, I get the error: "Error reading from drive L: data area: drive not ready (A)bort, (R)etry, (F)ail?". I'm not sure why it does this, but again I'm not even sure if I need to use the software when I have the jumper... I must say with everything connected and with the jumper in place or not, my BIOS will not recognize my drive at ALL. I have tried using the IDE HDD Auto-Detection like the Samsung manual says to do with no effect. I have made sure Parallel Port and Serial Port A are enabled under I/O Device Configuration in the BIOS. It does give me certain options underneath that talking about a location or something like that...

I'd really appreciate if somebody could help me out here. If it matters, I'd like to put Windows 7 or XP on the drive. As far as I know all the cables are working fine. I can hear the HDD when I turn on the computer, but again it is not recognized.

Thanks!

Person Having Similar Problem, but no solution: http://forums.techguy.org/all-other-software/483231-sata-drivers.html

P.S. Plug-And-Pray - Indeed

A: Why BIOS does not recognize new HDD in Compaq Presario Computer?

9 more replies
Answer Match 86.52%

Ok. Trying to fix a friend's computer, and seem to have run into a rather strange snag.  Problem:  The computer will not boot past the bios screen. Details:  When you power on the computer, the compaq logo with intel inside shows up and has the <F1 Setup> and <F10 System Recovery> options listed as well.  And this is about as far as the computer gets.  After this the whole computer is just locked up, no buttons work on the keyboard no lights come on the keyboard ect ect.  I've tried mashing on the F1 key as soon as I power on the computer and I can manage to get it to say *entering setup* but it still freezes after this point.  I've already tried eliminating possible sources of problem, all expansion cards removed, HDD and Dvd Rom disconnected, single memory module (256mb ddr 2700), only power, vga, and keyboard connected.  Ive also used the jumper on the motherboard to clear the cmos hoping that would solve the problem, to no avail.  I've tried using a different stick of memory and different memory slot as well...  Tried using both a ps2 and a usb keyboard... Ive even tried pulling out the jumper for the bios password protection (even though it didn't have a password on it, just trying anything I can think of).  The installed bios version is 3.1, and that is about all I know about the computer at this point, other than what the website tells me of it.   http://h10025.www1.hp.com/... Read more

A:Computer will not boot past bios screen, Compaq Presario SR...

Try clearing the CMOS again but this time remove the CMOS battery and hold the power button in for a few seconds. Then replace the battery and try booting up again.  On the back of the pc is the PSU condition led green or flashing?

10 more replies
Answer Match 77.28%

I have a compaq presario. The bios are poop. Does anyone know if there is a way to update the bios with areal manufacturer? Or am I stuck with compaq's bios? It would be really nice if there was a way to find out who makes the bios for them and update it. Any info would be great. Thank you in advance!
 

A:Compaq Presario Bios

You need to get the BIOS from Compaq. While the board maybe MADE by another company, who knows what slight changes to the specs were made.

When you do your next upgrade, build your own and get a real BIOS.

Like working on a NEW Dell PC, almost NO Options, no Temp monitors nothing.. junk... its a DELL!
 

1 more replies
Answer Match 76.44%

Hey guys, I have a Pentium 2 Compaq Presario 233MHz system. I was wondering if ANYONE know's hot to get into this systems BIOS. I have been trying and trying but when I hit F10 at the beginning I just get into the COMPAQ diagnostics and setup, and it says nothing about BIOS. My plans are to overclock it to see how it works, just for hands on experience, if you have any tips on that you could help me out with that also. Thanks for your guys help and I hope someone can help me. email me at [email protected] OR send me an AOL instant message at Daws202 which is my screen name. Thanks people!
-Adam-
 

A:Compaq Presario 233MHz PII BIOS

Just went threw the same missery
There is a pass word to the BIOS and you need to take out the motherboard battery to erase it. Leave it out for 5 secs, unplug the computer and turn it on unpluged to drain all the power out of it. then reinstall the battery and reboot.
You m,ay have to remove some of the perifs CD burner, JS Ect if it dosent work the first time to drain the power out of everything

Yes it sucks.
 

1 more replies
Answer Match 76.44%

Does anyone know how to get into the bios on a Compaq presario with a model number of 5340 ?? I have tried pressing delete key.. no affect, tried pressing
F1, F2, and escape, (one at a time) but the bios don't want to open up..
It shows nothing on the screen but the COMPAQ logo when started up. Then goes imediately to the windows 98 logo, then opens up windows 98.. It works ok, but I need to get into the bios to check some settings.
Thank You..
 

A:How to Access bios on Compaq presario

8 more replies
Answer Match 76.44%

hi folks, need help fast,

hi hope you can help i have a presario compaq which when i brought i went into some set up and where as when it loads it asks for a password before it loads.. i now want this off as its just annoying!!! i have the password luckily but whenever i go into it before it loads by pressing esc and try and disable it, and save config its still asks for it when i reboot any help or advice im really willing to pay i even have tried to defualt it and save but still asks any help would be amazing
 

More replies
Answer Match 75.6%

System error says 53607277 please help

A:compaq presario cq62 bios password

@robwall? Enter   42765879

1 more replies
Answer Match 75.6%

Hola buenos dias, Tengo una notebook Compaq Presario 21-N0F3AR la cual al estar encendida y quedarse sin bateria, dio un error de windows  (File:\BCD Error codexc0000034).Al querer entrar a la bios para poder cambiar el oredn de bootea para reparar dicho error, me encuentro que me pide un password de administrador, el cual nunca se configuro.Luego de los 3 intentos fallidos me da el codigo ERROR System Locked 0949F6ABHe ledio en varios foros y a mucha gente le ha pasado lo mismo. he tratado con todos los programas que hay en la web para tratar de sacar el codigo invertido pero todos sin exito.Por favor me podran dar una solucion?Muchisimas graciasDiego  

More replies
Answer Match 75.6%

I just restored this computer with the factory reset and I need help with the bios password the system diabled key is 59036668. Any help would be great.













Solved!

View Solution.

A:Compaq Presario C700 bios password?

Hi, Please try:     46994268 Regards.

4 more replies
Answer Match 75.6%

Can I know the BIOS Password for the laptop HP Compaq Presario C506TUIts shows the message as "System Disabled [13674]"

A:Need Bios Password for HP Compaq Presario C506TU

@Ponkanagaraj? Enter     zulquvm                       or                   cxgqu Regards, DP-K

1 more replies
Answer Match 75.6%

Can anyone tell me how to get to the BIOS
 

A:{Solved} accessing BIOS on a compaq presario

6 more replies
Answer Match 75.6%

First I want to say hello,as I just registered here on this forum.

I hope I haven't violated any of the rules.
The reason I'm adressing you is because of my (now old) computer (Compaq Presario 14XL242) that i wish to upgrade my computer to windows xp. In order to do that i need to update the BIOS.How do I do that?

Thank you


 

A:Compaq presario 14XL242 Bios update

Greetings, and welcome to TSG!!

Look on the manufacturer's Web site for the BIOS update. There should also be instructions on how to do so.

Try: http://h10025.www1.hp.com/ewfrf/wc/document?docname=c00034791&cc=us&lc=en&dlc=en&product=95128
 

1 more replies
Answer Match 75.6%

HI everyone! i need some help! i got COMPAQ PRESARIO V5206OM, and i forgot the bios password, when i give 3 times the bad password the laptop show me the next error: SISTEMA DESACTIVADO [01130], if somebody can help me i will be happy! thanks to much! 

A:COMPAQ PRESARIO V5206OM BIOS PASSWORD

Hi, Enter    yhtiwp                   or              ehejsej Regards, DP-K

1 more replies
Answer Match 75.6%

I erased the bios on a Compaq Presario 5340. Now I need to find a bios for it again. Compaq's site is no help at all.

Does anyone know where I could find one?

(my problem is that it will not boot to the HD. it will only go to the floppy disk with a program called KillDisk on it. i connected the HDs to a different computer and it worked fine without the floppy and booted to the OS. and yes the HD is first for boot order.)
 

A:Solved: BIOS for Compaq Presario 5340

15 more replies
Answer Match 75.6%

Cant get into my bios on my Compaq Presario 5304. I tryed delete and f8 but it just gives me to option to boot in safe mode. My CD rom drive wont work and i switched it out with another one but still wont work. I am not sure if they are both bad but I imagane that they arnt. Please help.
 

A:(Resolved) Bios Help Compaq Presario 5304

6 more replies
Answer Match 75.6%

my dad's old laptop was recovered after long time, but, it asks for bios password and we cannot able to remember any.. My dad said he wasn't sure it was there in the first place. it shows SYSTEM DISABLED 07437 if we try to guess the password for 3times. can anyone provide right code for the bios..?

A:Compaq Presario V3000 Bios password

@AshwinRuffian? Enter:      otrquj                      or                  toooa Regards, DP-K

3 more replies
Answer Match 75.6%

can someone unlock my bios hidden (advanced) features i need it i'm advanced user i need those tabsand all hidden functions unlockedbut if there's only hidden advanced and power tab and no more hidden settings send me the unlocked bios to flashModel:Hp Compaq CQ58Bios:InsydeH2O Setup Utility Rev 3.7 (after update)Bios Version:F.29tabsMain (shown)Advanced (Hidden)Security (shown)System Configuration (Shown, it have hidden features but the tab is shown)Power (Hidden)Exit (Shown)Please Unlock And send me to flash it!!!!!!!

More replies
Answer Match 75.6%

I just restored this computer with the factory reset and I need help with the bios password the system disabled key is 59196419. Any help would be great.Thanks so much.Spoiler (Highlight to read)     

A:Compaq Presario C700 bios password?

Please try-46894439  Hope this helps, for any further queries reply to the post and feel free to join us again  **Click the White Thumbs Up Button on the right to say Thanks**Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem. Thank You,GBL84I am not an HP Employee

2 more replies
Answer Match 74.76%

I have a Compaq Presario 2200 model laptop.

I have an issue where every time by laptop batter discharges the time clock resets. I believe that this is realated to the bios battery. I have taken the laptop appart properly via guide provided on compaq website. This is the maintenance guide with all the spare part numbers listed. However, this laptop is out of warranty.

My problem is that I cannot locate the bios battery anywhere on the board. Could someone with some experience pleae review the diagram for this model and tell me where the battery is?


Thanks,
Darmin
 

A:Presario 2200 Compaq - CMOS/BIOS battery?

First of all.

Have you tried to calibrate the battery by BIOS? < This might help a lot of problems.

Second

Have you updated your BIOS ?
 

2 more replies
Answer Match 74.76%

Hello, I am attempting to access the BIOS on my HP Compaq Presario CQ62. It prompts me for a master BIOS password (which I do not know), and reports an error "System Disable. Key: 87231156"Other threads indicate that this is a common issue. May I please have my master BIOS password? And is there any other way to recover this? Thank you so much!Brandon

A:Master BIOS password - Compaq Presario CQ62

@Brandon_S1? Please enter    38199198 Regards.

1 more replies
Answer Match 74.76%

Hi, cant enter bios setup, got error code: 56085878. Help please. Thanks

A:compaq presario CQ57 needs BIos administrator password

Enter the followng unlock code; 49983278

2 more replies
Answer Match 74.76%

After rebooting my system I now come to a screen to enter system password. Only thing is.. I never set this and there is no way around it.I have tried the take battery out reset CMOS trick that used to work in desktops to no avail. this is the message I get after too many password attempts. system disable key 92931076











Solved!
View Solution.

A:Compaq Presario CQ61 BIOS Password Unlock

Chick try. 23699078 Use that code to go into the BIOS.Disable all passwords that are enabled.If asked for the CURRENT password use that code.If asked for NEW password just hit enter.If asked to VERIFY password just hit enter.Save and exit. REO I must inform you that these services are not endorsed by HP, and that HP is not responsible for any damage that may arise to your system by using these services. Please be aware that you do this at your own risk.

8 more replies
Answer Match 74.76%

Sir,My compaq presario cq 60 i have forgot the bios password (Enter Administrator password ?). after 3 attempts i got a code 63186857 Please help me .











Solved!
View Solution.

A:Compaq Presario CQ60 - How to reset the bios password?

Hi Enter: 72884299

9 more replies
Answer Match 74.76%

Forgt the bios password to my presario CQ56 LAPTOP the errcode is 59091082 please help

A:forgot bios password's compaq presario CQ56

@n8kdg Please enter     46999004 Regards

1 more replies
Answer Match 74.76%

Hello sir, I have a problem in bios password. I tried to reset cmos by removing rtc battery. But i can't remove password. System disabled code is 03218. Thanks,Moewin

A:Compaq Presario v3000 BIOS Password Reset

Hi, Please try (lower cases)    ebceyfd   or mpf Regards.

9 more replies
Answer Match 74.76%

I can not use my pc .. I misspelled my bios password and now sends me an error code .. you poede give me an unlock code please. Error Code:  21501 first of all, Thanks  

A:Re: Compaq Presario v3000 BIOS Password Reset

Try entering the following unlock code: ckhi

1 more replies
Answer Match 74.76%

Says system disabled after 3 attempts at administrator password. Code is 63494577 please help!

More replies
Answer Match 74.76%

Hello sir,I have a problem in bios password. I tried to reset cmos by removing rtc battery. But i can't remove password. System disabled code is 09565.Thanks,MNK











Solved!
View Solution.

A:Compaq Presario v3000 BIOS Password Reset

When asked for password try nddo or vrckh

4 more replies
Answer Match 74.76%

Hi,I need my bios administrator password for a compaq presario cq57.I get system disabled error 61596522.Thanks.

A:compaq presario CQ57 needs BIos administrator password

Hello @kodoku Welcome to the HP Support forum. Please, try to enter this >> 74494504as a response code. This should let you enter BIOS, start your PC, unlock your BIOS and/or reset security settings. Let me know if this works for you

1 more replies
Answer Match 74.76%

Well, last week was going good until my computer decided to melt down. I reworked a Compaq Presario 4712 as a backup, but I can't figure out the bios setup sequence. Can someone please help me. I'm in the middle of backing my web site up, so I can move it to a secure server.
 

A:[SOLVED] Compaq Presario 4712 bios setup

13 more replies
Answer Match 74.76%

how to run the system bios in laptop Compaq Presario CQ57 with Windows 10?

A:how to run the system bios in laptop Compaq Presario CQ57 wi...

ANAKONDA wrote:how to run the system bios in laptop Compaq Presario CQ57 with Windows 10?Hi, Sorry, what are you trying to do ? We don't run the system BIOS. And from your question, all I can say: Please don't touch to BIOS, this is the shortest way to brick your machine. Regards.

1 more replies
Answer Match 74.76%

I have an older compaq presario CQ62 that i'm trying to get running for my father. It will not load stating "Windows failed to start. a recent hardware or software change might be the cause" Status: 0xc000000f Info: the boot selection failed because a required device is inaccessible. I have windows 7 on a bootable USB drive but it gives me the same error when trying to boot from the usb drive. when i try to enter bios to rearrange the boot order it's asking for a password and i have no idea what it is. It's giving me a code # 54391904 any way i can reset password or still boot from USB drive? thank you in advance

A:forgot compaq presario CQ62 BIOS password

 Hi, Enter: 41099320

5 more replies
Answer Match 74.76%

Need a bios password for a Compaq Presario CQ62-209WM System Disabled KEY: 5503579 Please Help. 

A:Need a bios password for a Compaq Presario CQ62-209WM

@curtism49? Check the code you've posted - it should contain 8 digits. Regards, DP-K

1 more replies
Answer Match 74.76%

When I start the computer up it goes to bios screen. It will not let me continue by pressing f2. F1 takes me to help screen, but when I exit that it is right back to bios screen and f2 does nothing.

A:compaq Presario s5200nx won't go past bios screen

Mcdolemom, welcome to the forum. Based on the age of the computer, I suspect a failed power supply unit (PSU).  Here is a guide to help you troubleshoot it. Please click the Thumbs up + button if I have helped you and click Accept as Solution if your problem is solved.

1 more replies
Answer Match 73.92%

Hi all,I have a Compaq Presario CQ61-310SV notebook that does not want to start ? the screen does not turn on and always remains blank. At startup, when I press power button:Lit only leds for Power, WiFi (orange color) and Touchpad;The fan turns on, but the screen remains blank;Caps Lock and Num Lock keys blink 2 times in a sequence;According to these data, I found that there was an error, indicating to failure of the BIOS. But, despite the fact that on the forum I found many of similar cases, no advice did not help me solve this error. So I decided to ask you for help, describing in detail what I tried hoping that you will point to my mistakes and help me to solve the problem.So:First of all, I tried to perform a hard reset by:Disconnecting the AC adapter, battery and all external peripheral devices;Pressing and holding down the power button for about 1 minute;Plugging the AC adapter back into the notebook;Trying to turn on the notebook;Also I removed the CMOS battery for a few minutes ? no result.Next, I tried to recovering the BIOS using key press combination «Win+B» hoping that my notebook has the emergency BIOS recovery feature enabled. But the notebook silently restarts automatically after few seconds after I released the power button. How I tried to do it?I turned off notebook and I unplugged AC adapter;I disconnected the battery and all external peripheral devices;I plugged AC adapter back into the notebook;Holding «Win+B» I pressed power button and I rel... Read more

A:Compaq Presario CQ61-310SV: BIOS corruption failure

I noticed that no one can/wants to try to help and I do not know why... If I did something wrong or you need more information about my problem ? please tell me about this and I certainly will update the post.

9 more replies
Answer Match 73.92%

I went to change the boot sequence to boot from my integrated DVD so I could reload my OS. After making the change I attempted to save the BIOS settings but the system locked up during the process. Now no boot, no screen, no effect when trying to get back into the BIOS. How do I (can I) clear the BIOS?
 

A:Compaq Presario X1000 (DK454AV) BIOS corrupted – no boot

7 more replies
Answer Match 73.92%

I just reformatted a friends Compaq Presario 3000 laptop with win xp pro. Everything was working fine on it until I updated the bios. Now the computer starts to come on and then shuts down after about a second. I have tried draining all the power but get the same result. All ideas welcome. Thank you.
 

A:Compaq Presario 3000 wont boot after bios update

9 more replies
Answer Match 73.92%

how to reset my bios passwords hp v3000

A:Re: Compaq Presario v3000 (V3230AU) BIOS Password Reset

Hi vikassingh, If you post the code that it gives you here,  then I will try to help you. -erico

9 more replies
Answer Match 73.08%

I was working on a customer's laptop, a Compaq CQ60, that refused to boot into windows and System Recovery disabled all recovery options except for Command Prompt.

On a hunch, after pressing Escape during BIOS boot, I selected HDD Test. The test ran and failed with "Replace Hard Drive." OK.. the laptop sat there for a few minutes and never did anything else, so I tried to get out of that screen. Nothing responded, so I just held the Power button to turn the computer off.

When I pressed Power again to turn the computer back on, the Power and Wireless LEDs comes on, the CD drive is accessed and then the HDD LED lights up for a second and goes out. The screen never comes up nor do the backlights.

I have tried hooking up an external monitor, but that never shows anything either.

I have tried taking the memory out, cleaning the contacts, putting them back in, swapping the modules around, booting with one or the other.... No effect.

I pulled the battery and the CMOS battery, unplugged AC and let it sit for a good half hour. I held the Power button for thirty seconds. Plugged the CMOS battery back in then the AC. Turned it on and still no go.

I cannot figure out WHAT could have happened!? Any other ideas? Thanks...
 

A:Compaq Presario CQ60 black screen no BIOS boot after HDD test

16 more replies
Answer Match 73.08%

I have a Compaq Presario CQ57-339WM and it won't boot.I tried to restore it, but I can't get into the bios to let it boot from CD.It says system disabled 67912930 after 3 failed attempts. Help!











Solved!
View Solution.

A:Compaq Presario CQ57-339WM bios password system disabled

Try >> 78670316

7 more replies
Answer Match 73.08%

hey i recently got a compaq presario v6000 from a friend and when i turned it on for the first time i noticed that it made 3 short beeping sounds which i found out that it doesnt have a bios image but anyway the power light a battery light flashes and then reboots but i cant see anything on the screen at all when its powered on. also the fans power on for at least 2 seconds then they turn off. i dont have a hard drive but i need to at least get to the bios so i can reinstall the os using usb drive.

any help would be great and aslo people have been telling me that my motherboard could be warped how would i fix this without buying a new one because i have no money at all for the laptop.

A:compaq presario v6000 wont display bios and screen is black

It looks like you may have Bad Ram: Compaq BIOS Beep Codes - BIOS Central.
Computer Does Not Start and Emits an LED or Beep Code Compaq Presario SR5510F Desktop PC - HP Customer Care (United States - English) Or it could be the Video adapter on the motherboard. Try removing one stick of RAM and get to the Bios. You can also download the ISO image for Memtest in my signature burn the image to CD with IMGBurn also in my signature or USB and boot off of the disc and run the tests on each stick of RAM separately.

3 more replies
Answer Match 72.66%

NOTE: THIS IS A COPY OF MY POST ON THE COMPAQ FORUM...getting desperate.

Hi, i bought a 6150b from a company auction. Everything worked perfect for the longest time. Then last week i went to go turn it on, and all it does is run the CPU fan for a couple seconds, flash the AC LED about 7 - 8 times, and while thats flashing the power and hard drive LED’s stay solidly lit. Then it completely turns off. This all lasts about 3 seconds at the most. That’s what happens when on battery power.

When on AC power, the same thing happens, except it continues doing the cycle over and over again until I unplug it.

I think it might have something to do with the LCD monitor, since it does not even show a slight flicker at all. No color change like it would from when turned off to a black back lit screen when turning on….simply nothing.

I opened her up (no warranty anyways) and checked all the connections for the keyboard, monitor, DVD drive etc....also reseated them as well, with no luck.

Pulled the both RAM modules and reseated them as well, nothing.

Pulled the battery as well, no change. Still cycles the same over and over again while on AC

There are no audible errors codes (real nice HP...), and im lost at this point.

Any and all suggestions are greatly appreciated.
 

A:Compaq Presario 6150b wont boot - no BIOS screen - powers on and off repeatedly

I think instead of just pulling and replacing the CMOS battery you might purchase a new one and install it. Proceed from there. If you get a screen and it's still has a problem try a new PSU. Jazz
 

2 more replies
Answer Match 72.66%

Hello all great website!

Compaq Presario 7000 series (model #7QSM11) using Windows ME, AMD 1332 mhz processor. My sister's computer. Hard drive was a 60GB, but it died. So I bought a new hard drive actually tried a 160GB first but thought the 137GB issue was the problem so now I am trying a 120GB western digital Caviar.

I found and successfully flashed the latest bios. (ROM date 3/28/02-786K2 Family). I checked the bios and it does see all 120GB. But when I goto partition it, I run into problems. Three methods tried: I tried to use Western Digitals included CD-ROM, even created the DOS boot floppy that they recommended on another system. Doesn't work keeps coming up with an error that something like A:\Auto???.exe not found. I checked the floppy that file is there?? Comes up whether I am booting from the floppy or from the CD-ROM.

So I tried fdisk from a Windows ME boot disk. Fdisk will only find/or report 24GB. I cleared the partition and tried using the Compaq restore disks but they came up with the same problem.
Am I right in thinking that this is a Windows ME issue?
Can you tell me how to fix this problem?

My computer is a Dell 8100, also running Windows ME but with a Intel P4, I installed a 200GB hard drive and had to flash the bios, and then I am not sure if it was Maxtor's DDO dynamic disk overlay or Intel's application accelerator, or the Flashed Bios, but Windows ME sees the whole hard drive.

I am so frustrated, I am not completely stupi... Read more

A:Compaq Presario - Installed a new hard drive 120GB; Bios sees all of it but Fdisk

15 more replies
Answer Match 68.04%

hi guys,

i recently discovered my firewall had been disabled and my computer was running slow. A few months ago, I had a google redirect virus that has not only returned, but has also caused my computer to load the system32 folder when i start my computer.

i also seem to have trouble installing programs like hijackthis, which i had to transfer from another computer.

thanks in advance!

oh and i'm running windows xp with at least service pack 2. i think i installed 3, but can't remember.

A:Computer problems Compaq Presario Laptop

btw, there are a noticable amount of viruses present on my computer that have replaced system files, added programs that cannot be removed from the add/remove programs list, and otherwise cannot be erased/fixed by ant-virus (avg and windows defender) or by conventional methods (trying to scan and replace system files)

this isn't really a shameless "keep me on page 1 instead of 12" bump, but i assumed this information would be more vital in having someone actually look at my HJT log, as my prior complaint hadn't garnered enough reason to justify more than one view.

thanks again

13 more replies
Answer Match 68.04%

windows wont start. message saying windows failed to start,put in windows installation disc.(i have no disc.)

A:compaq presario computer wont start up

Don't mean to insult your intelligence but can you Tap F8 before that message appears to get into
safe mode?

5 more replies
Answer Match 67.2%

I purchased a Compaq Presario s3310 om (2600 + amd athlon with XP Home Edition. S# 31316953) When I boot up the computer the computer Beeps continiously and nothing happens after that. I have done some research and want to confirm that this is a RAM Issue. The original Ram was 512 mb ddr sdram memory. I did a search on Diagnostic Compaq Bios Beep codes and a continiously beeping indicates Memory error - Reseat or replace and re test. Am I on the right track?  











Solved!
View Solution.

A:On startup the computer beeps continiously - Compaq Presario...

Nothing is lost by air dusting the RAM slots.  Not sure you interpretation of beep codes are correct.Beep codes: http://support.hp.com/us-en/document/bph07107 What is more bothersome is the purchase of a vintage 2003-04 machine that did not work. Also, reseat any other cards. You might also try a non-destructive System Recovery  http://support.hp.com/us-en/document/c00007689 

4 more replies
Answer Match 66.36%

I have the quickrestore disk, but I'd rather leave the programs on it. I just want my personal stuff gone.

Thanks!
 

A:Have a compaq presario 7550, bought a new computer, how do I wipe my info?

In a nutshell
Create a New User Account with admin rights
login to this new account
remove your user account and delete user files
delete any other files / folders you have created on the drive
Download and install Eraser
open Eraser's properties and set the secure wiping as required
run eraser and wipe the free disk space of your hard drive
that should do you
 

1 more replies
Answer Match 66.36%

My computer crashed yesterday.  I think thats the term for it.  Its running windows xp.  Well, I shut it off at night, and when I tried to turn it on in the morning, the computer came on , the fan started spinning, lights came on, but the hard drive kept making clicking noises.  So, I hurriedly took out the hard drive, and retrieved my data from the hard drive through that IDE-USB adapter.  So, at least that was safe now
 
I think the disk is bad, and I need to replace it.  However I dont really want to pay for a whole new operating system.  Is there a way to transfer the operating system from the old drive to the new drive with its activation status, so that I dont start gettting those pesky activation notices?
 

A:my computer crashed compaq presario sr1630NX. its the hard drive

You can use disk imaging software, such as Macrium Reflect FREE Edition, to clone the old hard disk to a new one.  Once the new cloned disk has been installed, you will be asked to restart your system after you first boot it, so that Windows can reconfigure for the hardware change.  You will not need to reactivate Windows if you do this.
 
One thing to watch out for is that if the new disk is a different size to the old one and you have more than one partition on the disk, the software may dynamically resize the partitions and if you have diagnostics and/or recovery partitions you might want to keep the size of those the same as on the old disk.

3 more replies
Answer Match 66.36%

I'm having sound problems on my old Compaq Presario 1255 laptop computer. A friend had sent a music file over AIM for me to listen to and I was trying to listen to it, but all I got was static.

Can anyone give me a suggestion? I'll go turn that computer on so I can use it via my networking setup and then I can try any fixes or ideas you can give me. I tried looking for a new integrated sound driver, but so far no luck.
Thanks to anyone who can help me!
 

A:Sound problems on a compaq 1255 presario notebook computer

Do you get this static sound all the time? or just with that one file? What type of file is it?
 

2 more replies
Answer Match 65.1%

I have a Compaq Presario Notebook computer with a 137GB hard-drive. I would like to install a larger hard-drive in the computer, 500GB or larger. Does anyone know the best way to do this? Also, I was told that I need to put the operating system, Vista Home Premium, on the new hard-drive once I install it. If this is true, how can I make a copy of the operating system on a CD or thumb-drive? Thanks in advance for any and all suggestions.
 

A:Solved: How to install a new hard drive in a Compaq Presario C700 Notebook Computer?

9 more replies
Answer Match 65.1%

Hi, My Computer a Compaq Presario SR1810NX with Windows XP Home Edition SP2 is having an issue with it wont get past the Compaq Logo Screen, like, I press the power button the PC powers on, Fan Speeds up and then slows down as normal, keyboard lights flash as normal and the Compaq Logo along with the v3.48 and ESC = Boot Menu options appear on screen, the things is that it wont get past this screen, it just sits there at the Compaq screen, the keyboard and mouse dont seem to be interacting with the PC since I press ESC or F10 for boot mode or system recovery but the PC wont answer at all, I've already Disconnected power source unplugged mouse, keyboard all but PC is doing the same thing just sitting at the Compaq Logo Screen, the computer doesnt make any sound at all no beeps or anything, it wont let me access Windows at any time, recent installations well could be that I just installed a Mobile Bandwidth Card just a couple of weeks ago, and also just a few days ago I connected my iPod Shuffle 2nd Gen to the computer and the computer wont recognize it at all, not even charging, I know this might be a virus or malicious software, but my computer has barely connected to the internet in the last weeks (I couldn't pay the Internet and I had to use my friend's Mobile Bandwidth Card I mentioned before) all I did while in Internet with the Mobile Bandwidth was some schoolwork and youtube videos, I need help urgently with this since I have to deliver a very important proyect for scho... Read more

A:Compaq Presario SR1810NX Not Getting Past Compaq Logo Screen

Try a power drain.
1. Unplug power cord
2. Hold power button in for 60 seconds or more then let go
3. Plug in power cord
4. turn on the power and try to boot to setup (BIOS)

If it enters the BIOS then you should be able to just press F5 to reset to defaults and then F10 to save and exit. The PC should work now.

However, if after the power drain you still can not get in the BIOS than there is a MAJOR problem which would require some type of repair.

1 more replies
Answer Match 65.1%

i dont know anything about computers so i will need a detailed explanation and i need to know how to fix it!! it just stays on the compaq screen

A:My Compaq Presario 2500 wont go pass the compaq screen

Hello lilevee22,

Before the problem started was anything added to or installed on the system?

Try booting to Last Known Good or Safe Mode.

Restart the computer during the boot process repeatedly tap "F8" you should get

the Advanced Options.

Let us know if able to get the system to boot with either option.

1 more replies
Answer Match 64.26%

Cant find the neccessary drivers for the internet have been here

http://h10025.www1.hp.com/ewfrf/wc/...en&cc=us&dlc=en&sw_lang=&product=3559331#N337

None of the drivers for ethernet or my wireless card work ???

This is a friends latop they had a virus so i reformatted and now no internet via wirless or wired
any help appreciated.

The virus was a virut file infecter virus so i was afraid to save any of the drivers for fear of reinfection.

Edit:

Tech Support Guy System Info Utility version 1.0.0.1
OS Version: Microsoft® Windows Vista&#8482; Home Premium , 32 bit
Processor: Intel(R) Pentium(R) Dual CPU T2330 @ 1.60GHz, x64 Family 6 Model 15 Stepping 13
Processor Count: 2
RAM: 1525 Mb
Graphics Card: Standard VGA Graphics Adapter, 5 Mb
Hard Drives: C: Total - 102547 MB, Free - 89975 MB;
Motherboard: Hewlett-Packard, 30D9, 83.21, CND80437PP
Antivirus: None

If any more info is needed let me know!!!
 

A:Solved: Laptop Compaq Presario C700 (from HP Compaq)

14 more replies
Answer Match 57.12%

How do you open the casing on compaq presario 5304. I don't want to breakit.\

Thanks.
 

A:compaq presario

Link to tell you all about your computer. http://h10025.www1.hp.com/ewfrf/wc/...ry&tool=prodinfoCategory&dlc=en&product=93186
 

1 more replies
Answer Match 57.12%

ok when i start up it shows the compaq logo then theres some beeps and it goes to a black screen. Any help? any way to reset all my stuff? i press f11 and it goes to some bios thing and i really dont know what to do. Thanks
 

A:Compaq presario help

16 more replies
Answer Match 57.12%

I friend of mine purchased this Presario in 2004. She hasn't had internet since about 2006, so she hasn't had any of the updates since then. I brought her tower home with me since I have internet to load her updates. We're trying to get it internet ready. When I brought it home last week nothing would open. So yesterday she gave me the system recovery disc. I started with the Standard Recovery, but there were too many files that it couldn't recover. So I then decided to do a full recovery. After the full recovery it was rebooting and it told me that not all the system could reload and I couldn't hit okaybecause it wouldn't read / acknowledge my mouse. So, I unhooked her computer and rehooked mine to see what her alternatives were. I found a website, they wanted to know all the things it wouldn't oload. All I can remember is that it was things that could me downloaded later like: Norton, AOL, Adobe, MSN, and QuickTime.

So, I unhoked mine and rehooked her's up (and booted up my laptop). When her's came back up it's saying: NTLDR is missing Pres Control + Alt +Delete to Restart

My question for you is there anyway I can save her conputer? She doesn't have a lot of funds, being a singe mother of a 7 yr old and I'm just a good friend trying to help her out.

Thank you in advance for any help you can provide

A:Compaq Presario

I decided to see what happened when I ctrl alt delete and then decided to do another recovery. Here's some more info (could not recover errors):
1. C:\WINDOWS\Help\SB\Training\WXPPer\Content\Wave\[email protected]
2. C:\WINDOWS\System32\ntdll.dll
3. C:\WINDOWS\System32\ntkrnlpa.exe
4. C:\WINDOWS\32\dllcache\dinput8.dll
5. C:\Windows\systme32\dllcache\licdll.dll
6. C:\WINDOWS\system32\dllcache\locator.exe
7. C:\WINDOWS\system32\viaservc.dll
9. (Black screen instead of error message)
9. C:\WINDOWS\Installe152ec/msi
10. C:\WINDOWS\Installer\1b2cc.msi

then all of after about 20% a big blue screen with following:
A problem has been detected and windows has been shut down to prevent damage to your computer.

IRQL_NOT_LESS_OR_EQUAL

If this is the first time you've seen this stop error screen, restart your computer. IF this screen appears again, follow these steps:

Check to make sure new hardware or software is properly installed.
If this is a new installation, ask your hardware or software manufacturer for any windows updates you might need.

If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use safe mode to remove or disable components, restart your computer, press F8 to select Advanced startup... Read more

3 more replies
Answer Match 57.12%

ok I hace a compaq that is all messed up. lets see one day the monitor would not work after a storm. Bought another, For a while the screen would be blue but change back to normal. The pc also would have a hard time starting up after it was in idle. We would do a hard start and for a while that worked. Now when I try to start it it turns on but the monitor says no vga/dvi input. There is also none of the preverable beeps that are supposed to be there so in short (well long)the motherboard is fried? So do I use it as a planter in the yard or is there a way to get it up and running. It runs on XP media center it has a micro ATX form factor motherboard it is also an AMD 64 Anthlon. ram is 256 mb 1Rx16 pc 4200 ddr2 533 mhz. With all that said can I just replace the motherboard and reinstall the reinstallation disks and be up and running? ( if it could only be so easy) What about the cpu. i know many questions here thanks for patients. Please help me. Tina
 

A:compaq presario

does your system have agp or pciex (or even pci) slot free? Is the graphics on board? It sounds like a graphics card problem, even if it is onboard. I'd try a replacement card (even if it's just a pci card) and see what happens...
 

1 more replies
Answer Match 57.12%

Hi. Does anyone know if a Compaq Presario SR1150NX does the display system support component video (Y, Pr, Pb) signal output function? Thanks
 

More replies
Answer Match 57.12%

How do you access the Bios on a Compac Presario 4110. I keep getting the message 162 Sytems Options not set. 163 Time and Date not set. Having visited Compac they were not a lot of help. Downloading the software recommeded by them was a waste of time, still got the above message. Tried all the usual keystrokes etc no good. Any suggestions would be appreciated.
 

A:Compaq Presario

9 more replies
Answer Match 57.12%

sir, can u help me, i can't fint my driver for compaq presario v3760TU
previously, i used vista home basic but i convert to window seven.. but i can't find my driver in hp/compaq driver web.. plzz help me..
-sory for my english so bad..

A:compaq presario

Were you at this Hp/Compaq download page ?


Software & Driver Downloads Compaq Presario V3760TU Notebook PC - HP Customer Care (United States - English)&

6 more replies
Answer Match 57.12%

I have purchased a Compaq Presario 600 with an Athlon XP 2200+ processor. I do not have a copy of Windows XP to wipe it with. Is there any way with the installed XP that I can refresh this system and remove data frome previous owners? Or Can I load Win 98?
 

A:Compaq Presario 600 ??

Compaqs usually have a hidden partition with all the factory loaded software on it in an image format. As long as it does and you can figure out how to access it you could probable do that - but you almost likely need the XP Product key and may need to reactivate XP after the recovery. XP can only be install on one machine at a time - so if they are still using it you are out of luck.

Watch the boot up for any recovery messages or take a trip to www.Compaq.com and look up the info for your make/model.
 

1 more replies
Answer Match 57.12%

I have a compaq presario. I have 2Gig memory. I changed services from ATT to comcast internet. now my pc needs to be wiped clean and set up again but when I got the computer I did not get the discs. how can I do this without discs> it wont open up the internet even though I am connected.

Please help
 

A:compaq presario pc

8 more replies
Answer Match 57.12%

my compaq presario cq57 says system disabled 62359871..plz help. thank you











Solved!
View Solution.

A:compaq presario

@sharp66? Enter   73031277

3 more replies
Answer Match 57.12%

Hi
I've been trying to figure this out on my own for about 4 years but I GIVE UP!!!
4 yrs ago I was doing a reformat from my OS CDs and the process got to a certain point (and I don't remember exactly where,sorry)and it just stopped formatting the OS. There are several software programs that came with my laptop that I WAS running before the reformat that never got formatted. One of them was MS Works and also MS Money and Cds have not been recognized since. Maybe all of the optical drive files/registry keys didn't install and I'm missing files/registry keys??????

I don't know if any of the following information will help and/or save time but these are just some of the things I've tried/come across in the last 4 years.

1. This is what happens after I insert a CD: after I hear it whirring, I go to the D:\ screen from MY Computer and click on the File button, there is not an option in that list that pops up for PLAY like there was befor the reformatt. There is only an option to "Write the Files to CD"....
Well, that wasn't what I was trying to do but clicked on it anyway and it tells me to insert disk. There is already one in there whirring !!

2. After inserting a music CD I've even gone to Start\Run and entered D:\
While the CD is whirring a small CD-looking icon will periodically flash but nothing ever happens. Just whirring. Like it connects but is missing a file/registry entry that makes it actually PLAY. Maybe?????


3. I've Live Chatted with both... Read more

A:Presario 900 DVD plays,won't recognize CD

Hi, and welcome to TSF!

It might be a failing optical drive. How many different CDs have you tried? Does it burn CDs successfully?

12 more replies
Answer Match 56.7%

Hi, i'm having a problem turning on my laptop. I'm using a Compaq Presario C502US. I've been using the AC adapter that came with the laptop but eventually the AC adapter became loose and broke. The charging icon (lightning symbol) wouldn't turn on anymore and I think the laptop has now run out of power. I've finally received a new adapter and when i plug it in the charging icon lights up. However the laptop still won't turn on. I've waited for about 2 hours but it still won't turn on. When i click the power button, the Power turns on and then it blinks. The Fan turns on for about 3 seconds but then it goes off and the power light blinks and the monitor won't turn on. Can anyone help me with this problem?
 

A:Compaq Presario won't turn on

Remove battery and power adaptor (ie all power out)

Hold down the ON button (to disperse all internal power)
Plug the power adaptor back in only (and to wall socket!)
Turn on!

If it works, turn back off, and re-install battery, turn On
 

5 more replies
Answer Match 56.7%

Okay. At work I have 2 Compaq Presario PC's. One is model SR1010NX and the other is S5010NX. They're fairly old. I have a Ubuntu 10.04 server set up that acts as my DHCP/TFTP/Samba server for booting with PXE, then installing the selected system and my custom application suite using only literally 2 minutes of my time to type in such details as the CD Key, Computer Name, etc.

So anyway, back to my Presario problems. Both computer conveniently do not have a Network Boot ROM (for example nVidia Boot Agent). So if I try to boot from network, Ill get a "Disc Failure". The S5010NX will not boot with a USB drive plugged-in period. It will get stuck on the red "Compaq" screen. If I unplug the device, it boots into BIOS/OS perfectly fine. If Im in the BIOS, and I plug the device in, the BIOS turns non-responsive, when I remove it, it starts responding again. Weird.

Here the 2nd chat session I've had with HP Professional Support (or whatever it's called). All I have to say is, I knew more about computers when I was 12 then these guys do.





Print active chat
[Tuesday, September 07, 2010 5:44 PM] -- Automatically generated message:
A support specialist will be with you shortly.
[Tuesday, September 07, 2010 5:44 PM] -- Automatically generated message:
You are now chatting with support specialist Priya K.
[Tuesday, September 07, 2010 5:44 PM] -- Priya K says:
Welcome to HP Total Care for Desktops. My name is Priya. Please... Read more

A:Compaq Presario headaches

Whoa! You're using this dinosaur? o_o
 

2 more replies
Answer Match 56.7%

Have a Compaq Presario 1020 - laptop. Info is as follows -
Series 2900A
Model FBV1433VQL1J
Serial V644HZD50299

Need a maintenance manual. Any help would be appreciated. Thank you.
 

A:Compaq Presario 1020

http://h10025.www1.hp.com/ewfrf/wc/product?product=94911&lc=en&cc=us&dlc=en&lang=en&cc=us
 

3 more replies
Answer Match 56.7%

I've searched this site, I've asked HP/Compaq, and I've checked search engines but still don't have an answer, so wondering if I can find it here.
I have a Compaq Presario 700 with what I believe is a dead hard drive. I want to replace it, but not sure if it is necessary to copy the files from the drive first. I don't think it's possible, as the drive doesn't seem to work at all. Can I replace it with a new (upgraded) hard drive and just run the original Windows QuickRestore discs, or is there something more to it that I would need?
Here's what happens: I switch the laptop on and it wants to start up, but then, before Windows is running, the hard drive begins it's lovely scraping and clunking noises and I eventually get a black screen with plain text saying windows had to shut down... and is beginning dump of physical memory. Of course, this all started after some fool (maybe me, maybe not) dropped the laptop.
Every site I've checked says I'll need to create a backup of all files before replacing the hard drive. I didn't have anything on there that I need to save, so am wondering if I can just run the QuickRestore and get back to business as usual.
 

A:Compaq Presario HDD replacement ?s

Welcome to the TSG forum.
Which Compaq Laptop ???
http://h20180.www2.hp.com/apps/Look...ery=Compaq+Presario+700&submit.x=9&submit.y=3

Have you backed up all your personal Data ??

Yes .. just put in a new HD .. and run the recovery CD/DVDs
This'll put it back to the way you bought it .. assuming no other problems.
 

2 more replies
Answer Match 56.7%

I have an older compaq presario 5000 (5wv260), i want to upgrade the memory in it. I know it takes sdram, 168 pin, but i dont know if i need parity or non-parity. OR ecc or non-ecc... anyone know what this computer takes?
thanks
 

A:compaq presario memory help..

6 more replies
Answer Match 56.7%

Hey everyone I am having the same problem again as I was having before with my Compaq Presario 5000. It seems to just freeze up when I am on it or not. Sometimes I try to move the mouse to get back into Windows from the screen saver and it does nothing. At all! And sometimes in the middle of surfing the web and listening to music it just freezes up again and I have to hit the power button just to get it back up and running. Can anyone help out with this? I was asked to run MemTest before but I have no idea how to do this, so could someone help out? Also, since I am not a complete newbie, but darn close when it comes to the whole hardware side of computing, how can I tell what is causing interference with what when it comes to the hardware I am running and wether or not the latest drivers are installed? Thanks again and hope to get this resolved quickly.

Compaq Presario 5000
UWAVE Motherboard
832MB RAM
AMD Athlon 901Mhz
eVga GeForce2 mx 400 64MB PCI
Sound Blaster Audigy 2 ZS Platinum
Sony DRU-530 DVD +-Drive
Windows XP Home SP1
 

A:Compaq Presario Freezing up again!

13 more replies
Answer Match 56.7%

I replaced my LCD cable (with two different cables) from the the stock one because it wouldnt fully display if not pushed all the way back. When I replaced the cable I put it all back together and it comes on without the previous problem but now it displays 4 identical screens like. 1 23 4I have tried updating the drivers for the video chooser and have even loaded previous drivers but to no avail still 4 screens. Can anyone help me out?

More replies
Answer Match 56.7%

Hello:
I'm making some changes to a compaq presario 4660 (dinosaur) and it's running windows 98. I cannot get into bios. F2, F1, delete and Tab do not get me in. I searched on google and really didn't receive good results. Well it did say that F2 would get me in, but it does not. Seemed to me there was another way to get into bios?
 

A:compaq presario 4660

16 more replies
Answer Match 56.7%

I have a Compaq Presario 1200 laptop that won't come out of hibernation. With either the battery or A/C cable the power on light on the keyboard will come on after the power switch is pressed and a couple of seconds of clicks from the vicinity of the 3 1/2 floppy or the hard drive area but nothing else - no beeps or anything on the screen.
I talked to Tech support (I am out of warranty) and tried their suggestions - removing all power and pressing the power button and then reinserting the battery; turning it off, removing power for 24 hours and then turning it back on.
One suggestion I had from another source was to remove the CMOS battery but I can not figure out how to access that part of the case. I can get to the hard drive but not the battery.
Any suggestions or directions on removing the CMOS battery?
 

More replies
Answer Match 56.7%

i have a lap compaq presario v3417la i used win vista , then i move to win 7 ultimate , and disconect sound device , can you help me ? please

-[ EVEREST Home Edition (c) 2003-2005 Lavalys, Inc. ]------------------------------------------------------------

Versión EVEREST v2.20.405/es
Sitio Web http://www.lavalys.com/
Tipo de informe Asistente de informes
Ordenador LUISGUZMAN-
Generador Luis Guzman
Sistema operativo Windows 7 Ultimate Media Center Edition 6.1.7601
Fecha 2011-08-19
Hora 12:59
--------[ Resumen ]-----------------------------------------------------------------------------------------------------

Ordenador:
Sistema operativo Windows 7 Ultimate Media Center Edition
Service Pack del Sistema Operativo Service Pack 1
DirectX 4.09.00.0904 (DirectX 9.0c)
Nombre del sistema LUISGUZMAN-
Nombre de usuario Luis Guzman

Placa base:
Tipo de procesador Mobile , 2000 MHz
Nombre de la Placa Base Wistron 30D6
Chipset de la Placa Base Desconocido
Memoria del Sistema 960 MB
Tipo de BIOS Phoenix (11/27/08)

Monitor:
Tarjeta gráfica GeForce 7150M / nForce 630M
Tarjeta gráfica GeForce 7150M / nForce 630M
Monitor Monitor PnP genérico [NoDB]

Almacenamiento:
Controlador IDE Controladora estándar PCI IDE de doble canal
Controlador IDE Controladora estándar PCI IDE de doble canal
Controlador IDE Ricoh Memory Stick Controller
Controlador IDE Ricoh MMC Host Controller
Controlador IDE Ricoh xD-Picture Card Controller
Disco duro WDC WD1600BEVS-60RST0 ATA Device
Lector óptico MAT... Read more

A:Compaq presario v3417la

Not too sure what you need help with.
Do you mean the sound does not work since upgrading to Windows 7?

This is because the existing audio driver is not compatible with Windows 7, and unfortunately HP/Compaq do not have any Windows 7 drivers for the Presario V3417LA. The Windows Vista driver might work. You can download it from here:
http://h10025.www1.hp.com/ewfrf/wc/...3&lc=en&cc=us&dlc=en&sw_lang=&product=3437668

Click the 'plus' symbol next to "Driver - Audio", then click "Connexant high-defintion audio driver".

If this driver does not work you will have to use Google Search to try and find one that does.
You really should have checked what drivers were available from the Compaq website before upgrading to Windows 7.
Some older laptops are just not suitable for upgrading to Windows 7 because of possible driver issues.
 

1 more replies
Answer Match 56.7%

Wont turn on at all no lights no nothing any ideas?
Thanks
Perry

A:Compaq presario c300

Compaq Presario C300 General Troubleshooting guide:

http://h10025.www1.hp.com/ewfrf/wc/document?docname=c00372748&lc=en&cc=us&dlc=&product=3213867&rule=2144&lang=

3 more replies
Answer Match 56.7%

I have the best luck with computers ever. My brother wanted me to format his oldschool compaq presario 5000 computer so I formatted with the win XP setup disk, when I went to restart to start installing windows after the format it takes me to a blank screen that reads:
"Couldn't open drive multi(0)disk(0)rdisk(0)partition(1) NTLDR: couldn't open drive multi(0)disk(0)rdisk(0)partition(1)"

I have booted with floppy and fdisk, fdisk /mbr, formatted about a million times using FAT and NTFS file systems, I have deleted all partitions, did everythinig I can think of.

Does anyone have any idea of how I might solve this and install windows? I know the HDD isn't shot because I can put it in my other comp and actually do a full win install, but when I place it back in the compaq, it brings me to the same error screen.

Any help would be greatly appreciated. Thanks guys.

one more thing, I am kinda a n00b at this sorta stuff so any ideas please give me the *hold my hand* explination and guide me what to do with step by step instructions, thanks again guys!

A:Compaq Presario problems PLZ HELP!

Check in your BIOS and make sure you have the right HDD displayed. It would be best to set it to auto. Also you could try setting the BIOS back to the default values.

3 more replies
Answer Match 56.7%

A friend has a Presario X1300. It has a small problem. The power button only works once in a while (perhaps 1 in 20 presses). I thought perhaps it was a cold solder joint but even after touching up the button's pads its still has the problem.

It could be a bad switch, it looked like the switch had previously been replaced (although he hasn't had it serviced except to put in a new hard drive about a month before the switch went bad).

I found a post that indicated that someone found schematics for the motherboard and I was hoping that someone here would be able to point me in the right direction. I didn't find them on google. I'm going to replace the switch first, but if that doesn't work I have to assume there's some other problem that will need debugged.

I hate to see such a nice laptop go to waste because of a stupid power on problem.

I have found the service manual online. Its great, but has no schematics.

Thanks for any ideas you can offer.

Raydude
 

More replies
Answer Match 56.7%

Installed with Vista Premium, i've realised that it has a Recovery Partition and im not sure how to use it. my computer came with a windows vista disc, but im trying to recover Vista and im not sure how to do it. maybe someone can give me a heads up on how to do it.
 

More replies
Answer Match 56.7%

Compaq Presario 3000+ AMD Sempron processor
Windows XP SP3
1 gig PC2700 memory
80 gig IDE HD
430 watt OS
Video and sound add in cards

On power-on the power light comes on, and the fans run, monitor is black.
 

A:Compaq Presario - no boot

16 more replies
Answer Match 56.7%

My compaq was working fine until one day it just went off during a user session. Pushing the power button made it try to start but when it began to load windows 98 it quit again. After serveral retries it finally started up again. It ran OK for about one week , then just went off again. This was during a user session.(user session meaning it was in use at the time). I tried to restart it but it would not restart. Finally it tried to start, then said press F2, then the video went out. Nosthing shows up on the screen now. When powered on you can hear the hard drive start up but that's about it. The three year warantee lapsed about a year ago . I was wondering whether or not this has something to do with the cmos battery. Apparently several people I know who purchased a Compaq laptop have run into the same problem. I have a friend who owns an IBM thinkpad which has done precisely the same thing. Any suggestions.
Sincerely
Frank
 

A:Compaq presario 1200XL111

It is possible for the cmos battery to cause similiar problems, but from what you are saying it looks like a processor problem. For the system to just shut off in the middle of being used and unable to start up again, shows the possibility that the processor has overheated and the machine has powered off, however because the machine is still too hot it wouldnt fully start up again.
To say that your video has then gone, could mean the processor is completely knackered, signs of life can still be seen from the machine but nothing will appear on the screen, in most cases the monitor will stay on standby even when the machine is powered on.

I suggest a new processor, with new heatsinc and fan.
 

3 more replies
Answer Match 56.7%

I have a f560US AMD Sempron 3500+ 2.8 GHz 1.5 GB Ram 32 bit and I am trying to boot to Linux from a USB thumb drive. I installed Ubuntu using Unetbootin on my 8 GB stick but I can't seem to make this laptop boot from the USB. I've gone into the bios and tried but have failed. Help me, please.
 

A:Compaq Presario won't boot from USB

Does your laptop allow booting from USB? Did you see the USB flash drive listed in the boot order screen?
 

1 more replies
Answer Match 56.7%

I have a problem with my laptop screen. The screen is dark, however, the data is still there. Can't turn lamp on, or change anything, but can hook up to a monitor and it works. Can I fix the screen to work again? If I hit the button that turns the screen off and closes the computer down, the picture pops up for a few seconds and it is slightly red.
 

A:Compaq presario R3000

Its most likely that the backlight has failed. It can be fixes but it costs a upwards of $100 to do by a professional. You could try buying the parts online and doing it yourself though if you are technically inclined.

Here's how: http://www.laptoprepair101.com/laptop/2007/12/09/replace-laptop-backlight-ccfl-lamp/
 

1 more replies
Answer Match 56.7%

i have a compaq presario SR5210NX with windows vista home premium ,it has a problem in/windows/system32/ntkrnlpa.exe,the state is 0xc0000225 and the information says the kernel doesnt responde or isnt working .it says introduce the installation disk windows ,but i dont have it and i couldnt enter to the recovery system

More replies
Answer Match 56.7%

Hello! I am attempting to change a 80mm fan in my Compaq computer. The fan I want to change is, I believe, called the CPU fan. It has a lever next to it and 4 screws holding it down. My question is this: Do I have to move the lever on the side of the fan in order to pull the fan up and proceed to remove the screws or do I just remove the 4 screws?  Also, how do I remove the screws considering the awkward position they are in? (I've been working on trying to remove the screws; however, it is difficult to maneuver the screwdriver into the top of the screws to remove them. This is because part of the fan case is above the screws making it necessary to place the screwdriver sideways in order to remove the screws.) Thank you for your response.  

More replies
Answer Match 56.7%

I was wondering how people thought of the Compaq Presario laptops as i am thinking of purchasing
 

More replies
Answer Match 56.7%

I just bought and set up a new computer system, and am now trying to get my old one to boot, so that I can migrate the files needed for the new system. The monitor doesn't come on, and all I'm getting is a fast blinking green light on the tower. I've un/replugged all cables and power cords, and I know the monitor is OK because it belongs to my husband's matching computer, but my old one won't boot.

Help!!!
 

A:Compaq Presario won't boot!

I'm desperate, guys! Is there any other information I can give you to help resolve my problem? I have the Easy Transfer Cable for Vista all ready to go (and the software loaded in the old computer before I disconnected it and moved it to the card table), but I can't get my Compaq to boot.

If you can't help me, I guess I'll take it to Best Buy tomorrow and let the Geek Squad have at it...
 

3 more replies
Answer Match 56.7%

My laptop wants an administrator password that I don't know. Shows a system disabled code of 91550023. What do I do?

More replies
Answer Match 56.7%

I hit the power button this morning and nothing happened. Tried unplugging and holding power button in and still nothing.
 

A:compaq presario will not turn on

Please post your system specs, exact model Presario, include any upgrades or modifications please.
 

1 more replies
Answer Match 56.7%

If any here has an HP Pavilion or Compaq Presario PC or Notebook (current models), they will notice that the fan kicks in when needed. The fan doesn't really annoy me as much on my Compaq laptop, but on my HP desktop it is really annoying and loud. I think it forgot that it was only supposed to come on when needed because it is now on almost all the time. Can someone explain to me how this fan works in more detail and how I can possibly adjust when it comes on or at least the fan speed, SOMETHING!!! Thanx in advance.
 

A:HP/Compaq Pavilion/Presario Fan

If the fan kicks in more then it used to it might mean that the computer needs a cleaning. These fans are temperature controlled and only kick in when a sensor detects the temperature to be at a certain level. Sone fans need to be on at all times - like the one on the CPU - but it may be possible to control it speed with software or BIOS settings.

Speedfan comes to mind, do a google search for it. It will list the motherboard temps and allow fan speed adjustment if the board supports it. If you have a case fan you can control its speed, as for the CPU fan - thats best left on a full speed.

First, open up the case and see if it needs a cleaning. You can also replace stock fans with quieter ones if they are too loud or wearing out.
 

2 more replies
Answer Match 56.7%

Recently took some hits on my Compaq Presario 7478 system. Got two or three nasties via the 'Net. After McAfee's virus scan and removal, began experiencing weird happenings, such as system closing down and restarting. Then just not starting. Tried a few remedies [probably inadvisedly], and finally the system seemed to hang on my restore at the same place repeatedly.
Ultimately the system could no longer establish my OS. Restore failed.
Bottom line: Could not invoke computer restore. Could do nothing with this computer.
Q... Being compaq is the BIOS set to a certain condition that would prevent my reformatting the hard drive and restablishing an OS? Is this an option I can override? If I were to piggy-back the existing hard drive onto an operating hard-drive and reformat would that solve this problem and permit me to then create or repair the hard drive subsequently to get my compaq back?
Sorry this is so wordy...
 

A:Compaq Presario dead

Have you tried disabling System Restore; then re-enable for a fresh start?

Failing that, format and install OS per instructions in your manual or the CD which came with your computer. If no CD, the OS should be installed in .cab files in Windows Explorer.

The BIOS should already be properly set
 

3 more replies
Answer Match 56.7%

I am upgrading a Compaq Presario 5000 model #5WB220 with a very low 15 GB hard drive for a friend. It currently has Windows ME and there is no Compaq Restore CD.

I have increased the memory to 320 by adding an additional 256 MB RAM.

I am wanting to totally replace the 15GB hard drive with an 80 GB hard drive and load Windows XP Home.

The problem I am finding out is that Compaq has propriertory info on a partition within the existing drive. From what I understand without the Restore CD, I can't put the new drive in.

I'm wondering if there are any other alternatives to doing this.

Can I install XP on the existing drive and then transfer all the data (to include the compaq proprietory info) to the new drive in a slave position?
 

A:Upgrade Compaq Presario

10 more replies