Tech Problem Aggregator

Solved: SATA HD power adapter

Q: Solved: SATA HD power adapter

Recently bought a SATA HD adapter to read an old 3.5" HD. for some reason it only shows 53 GB instead of 120 GB. Also cannot see any old files that i had on there previously. Any way i can retrieve all the data?

A: Solved: SATA HD power adapter

9 more replies
Answer Match 68.46%

I made a service call today to set up a new Dell workstation. It had no PATA drives, only SATA, and no 4-pin molex connectors on the power supply. We need to connect his 500-Gigabyte PATA (aka old IDE) disk. I have already installed an IDE (PATA) controller.

I cannot find a power adapter that will take me from the new SATA power supply to a 4-pin molex.

Anyone know where I might find one?
 

A:Need power adapter from SATA to 4-pin molex

11 more replies
Answer Match 59.64%

I recently purchased an IDE to SATA adapter. I plugged the IDE end into the harddrive but when i tried to plug the SATA end into the mobo the SATA connectors were "above" the connections on the mobo this is on a Toshiba laptop.
Are there certain adapters for certain laptops? I`m new to these and thought they would all be the same as the research i did on the net said nothing about there being different adapters for different laptop mobo`s.
The only reason i bought one was because my hdd died and i have a few spare ide hdd`s and instead of buying a new hdd i thought i`d try an adapter.
All info greatly appreciated.
 

A:Solved: IDE to SATA adapter

10 more replies
Answer Match 58.38%

I'm looking to purchase in the UK a powered USB to IDE/SATA lead and having looked on ebay and amazon, I have not seen a unit with a decent set of reviews and UK plug

anyone actually purchased on of these units and could recommend a good quality unit.
I intend to use on customer provided harddrives, to attempt to recover data, so do not really want a low quality unit - read about a couple damaging the harddrive - which is the last thing I need

any now compatible with USB3

thanks
 

A:Solved: USB to Sata/IDE powered adapter recommendations

6 more replies
Answer Match 57.54%

I want to transfer data from my hard drive in my laptop (Lenovo Y480) to a hard drive in my desktop. the cables for the sata adapter do not fit the hard drive from the laptop. Is there a different form for a 2.5 hard drive and a 3.5 hard drive?
 

A:sata to usb adapter cable dosen't fit sata hard drive in laptop?

Does the drive have an adapter need to remove to expose the SATA conenctors? I don;t see anything about the Y480 not having a standard SATA drive and laptop and desktop SATA connectors are the same.

Maybe post pictures of both the drive and your SATA cables.
 

2 more replies
Answer Match 56.7%

I wanted to know if there is a way to connect a SATA hardrive to an older motherboard that has no SATA connection
 

A:Adapter to connect SATA HD to motherboard with no SATA connection?

You can always use one of these PCI SATA adapter cards: http://www.newegg.com/Product/Produ...ESTMATCH&N=-1&isNodeId=1&Description=pci+sata

A computer as old as you're describing will likely have an old type standard PCI slot, and NOT a PCI-E (PCI express). be certain to verify which slot you have, before you make a purchase. These are two entirely different interfaces, which are not interchangeable.
 

1 more replies
Answer Match 56.7%

The mother board is an ASUS P5Q? I know the adapter is working because I can hook the cable that comes from the case to another sata slot shut down turn the enclosure on and boot and I have a third hard drive. But that is not how I would like to do it. If the mother board would recognize the enclosure it would give me an icon in the tray to shut it off and I would not have to reboot to back up something.


Thank u for any help
 

More replies
Answer Match 55.86%

Hello, I've bought a lenovo 510-15isk laptop, so far, great laptop!But i have a question. Where normal the dvd drive is now a empty tray, i knew that when i purchased the laptop.You can insert there a another hdd in the plastic housing. ( there are holders inside for the hdd and you can read the maxium thickness of the hdd)But you need a sata and power adapter from the hdd to the motherboard. My question, is there a adapter from lenovo, and does someone have a serialnumber?I've searched online and read the manual but couldn't find anything so far. Best regards,  

More replies
Answer Match 55.44%

I was given this case from a friend (Asus TA881 ATX Mid Tower) as he couldnt sell it on ebay I though what the heck I have a PC where I dont really like the case anyway so I swapped them over..Problem is on this PC I have 2 sata Devices Pioneer DVD burner and WD Sata 2 HDD I thought no problem till I saw the PSU its only 300w with 1 sata power connector normally this wouldnt be a problem just take the PSU from my old case and put it into the new case except that PSU dosnt fit its too big for the case and Im not going to carve the case to make it fit..

I see only 2 options,

1)Get a PSU that fits
2)Get an IDE version Poneer Burner

Maybe #3? Is it possible to get a IDE power connector and convert it to one that suits Sata Devices. ?? Im thinking no but Im not really sure..

Thanks to anyone who can help..
 

A:Solved: Only 1 Sata Power Connector

http://www.tigerdirect.ca/applications/SearchTools/item-details.asp?EdpNo=570342&CatId=468
Is this all you need?
 

2 more replies
Answer Match 55.44%

I'm going to be installing a Western Digital "Raptor" SATA hard drive into an Asus P5Q motherboard. The drive came with a data cable, but no power cable.

The hard drive itself can accept a SATA-style power-cable, a four-pin (molex) connector, or both (seems like overkill though).

I have two cables on hand: one is a four-pin (molex) to SATA-power connector cable, the other is a six-pin to SATA-power connector.

Can I use one of those cables to connect power to the hard drive and if so which one is preferable, the four-pin molex or the six-pin? I'm pretty sure I'll have both types of connections available from the PSU (lots of left over connectors) so I can use either.

Or... could I bypass the SATA-style power connector altogether and just plug in one of the molex connectors since the drive has a four-pin (molex) "socket"?

I'll go with whatever is best. Input appreciated!!

Thanks in advance.
 

A:Solved: SATA HD Power Connection... 4 Pin? 6 Pin?

I think the molex is there because some PSUs didn't supply enough SATA power connectors.
Either will work, but on my older ASUS board I prefer the molex because they seem to have a better connection.
 

2 more replies
Answer Match 55.44%

Hi, is the black connector to the right in the first picture a SATA power connector? The reason why I'm asking is because I noticed that molex was printed on the connector, but it looks different then a molex connector. Also, I'm not sure if this would help answer the question or not, but the other end of the cable (featured in second picture) has what looks like a molex connector, which is connected to a device other then the power supply. At least, that's what it looks like, I've looked at the connectors and cables carefully many times.
 

A:Solved: is this a SATA power connector?

6 more replies
Answer Match 55.02%

Hello!

I received the following message when I am booting up my Dell ATG Laptop. Does this mean I need a new power cord? If so, is there anywhere recommended to purchase or do I just go to the dell website?

The AC Power Adapter Wattage and Type cannot be determined. The battery may not charge. The system will adjust the performance to match the power available. Please connect a Dell 65W AC adapter or greater for best system performance. To resolve this issue, try to reset the power adapter. Strike the F3 key (before F1 or F2 key) if you do not want to see the power warning again.

Strike the F1 to to continue. F2 to run the setup utility, Pree F5 to run onboard diagnostics.
Thank you so much for the assistance!

Baxter
 

A:Solved: AC Power Adapter

It may be the AC Adapter, or the internal battery has died.
 

3 more replies
Answer Match 54.6%

I just bought a Western Digital Caviar Black WD1001FALS 1TB and I went to hook it up and the SATA power cable is backwards compared to the others. The other power cables form an L shaped like this -----
I ....that is it if you're looking at from the back, the L goes down on the right side. On the WD drive, it dips down on the left side?!? I didn't realize there was another type of power cable for a SATA drive.

The cable connector on back on the WD is like this ------
I

I have a Corsair HX620 modular PSU...I wonder if there is some type of adapter I need or something without going through Corsair. I've emailed them too but no telling how long that will take.

Kevin Palmer

Apparently my attempt at showing you didn't work on here.....at any rate it's like I said...on normal SATA power connectors, the corner goes down on the right, but on the WD, it goes down on the left.
 

A:Solved: Weird Power SATA Cable....

I'm an idiot! I'm just saying it so no one else has too....NEVERMIND....SIGH......
 

3 more replies
Answer Match 54.6%

Many SATA disks have pinouts for both SATA and ATA/133 (IDE) for both the data and power connectors.

I saw a system today where a SATA disk was connected using the SATA connector and cable for the data but the IDE connector and cable for the power.

Is it OK to do this? Seems strange, or do the power connections merge on the pc-board so that it does not matter which connector is used?
 

A:Solved: SATA disk power connections

6 more replies
Answer Match 54.6%

I'm looking to add three drives to my system. However, I only have two SATA power connectors.

1. SATA-II 320 GB (OS installed)
2. SATA-II 1TB (Caviar Green WD10EARS)
3. SATA-II 1TB (Caviar Green WD10EARS)

I have enough spare molex connectors. when I connects my third drive using SATA power connector (4 pin) system start hanging/freezing and in worst case my third drive disappeared.

Note: I have changed many sata power connector (molex to sata connector) but the result is the same

PC Specifications
Processor: [Intel(R) Core(TM)2 Duo E8400 @ 3.00GHz
Motherboard: P5E-VM DO
RAM: 2GB (667MB)
Super Drive: disconnected
using built in VGA
PSU:TOWERS power Supply AT-400 watt
what should i do?
Is 3.3V necessary for SATA-II.

My question is why molex to sata connector 3.3v orange cable missing. Lets say if i cut SATA connector (including orange 3.3v cable) from other faulty PSU can i use it for third HDD.
This guy says you can do it.
http://www.tomshardware.com/forum/291776-28-make-molex-sata-adapter
 

A:Solved: Adding new WD HDD using SATA Power Connector

6 more replies
Answer Match 54.6%

I have a three port SATA controller PCI card, into which I successfully ran two 500GB SATA HDDs. One of them had the old-style 4-pin power socket (PATA IDE drives), while the other needed an adapter cause it was a SATA power connector only.

Anyway, all was fine until I purchased a third SATA drive and plugged it into the remaining slot, situated on the out-facing metal plate of the controller card. This one also needed a power adapter for my old-style PSU. The new drive worked fine, but the second of the two original drives fails to load.

First of all, am I right in guessing that it's not a power issue? The reason I think this is because in the past when I've plugged an unpowered drive into the SATA controller, it renders the SATA controller useless, and none of the SATA drives appear in My Computer. So, because I can get two out of the three drives to work simultaneously, am I right in thinking that it's not the power?

Is there some sort of SATA BIOS that I need to tap into to enable something? How is this done?

Any ideas?
 

A:Solved: SATA HDD #2 fails to power up after plugging in HDD #3

Should I just accept that this is infact only 2 port, and that the 2nd and 3rd slot are shared between one inward facing slot and one facing out of the computer case? Or is there some way to enable the 3rd port?
 

2 more replies
Answer Match 54.6%

I just bought a wireless highpower adapter since my room is so far away from my router/modem.

I used the software that came along with my adapter to scan the surrounding network, but it didn't pick up on my net work no matter how many time I scan it. But it does pick up a few of my neighbors' wifi signal.

But I could connect completely fine with my laptop itself.

OS: Window 8
adapter: Prolink PAN2001
 

A:Solved: Wi-Fi High-Power adapter

8 more replies
Answer Match 54.6%

Hi all. I'm semi-reliably informed that my main board is dead.

If my HD survived whatever traumatic event caused the above, I'd like to attempt to salvage some of the data from it. It's a Maxtor DiamondMax Plus 9 80GB ATA/133, 3.5 series.

So far, Ive found this adapter which seems like what I'll need to connect the HD to a laptop via USB in order for it to show up as a removable drive from which I can pull files. Note: I don't want to open the laptop & connect directly vice the DVDRW as it's still under warranty.

So, my question is ... what's the power source on the adapter for? Is it in case you want the connected drive to function as a working drive as opposed to just a storage device?

(sorry, no doubt this is a really dumb one, hardware's just not my thing )

Any advice on this specifically, or any general comments on the likelihood of success of this operation, gratefully received. TIA,

bomb
 

A:Solved: USB > IDE adapter; Power Source is for what?

15 more replies
Answer Match 54.18%

i am in the process of ordering parts to build my 1st computer but i am not sure about the sata hard drive power connection. do i need a special power supply to run the sata drive as the case i am ordering has a 400 watt supply in it or is there an adapter that i can purchase to adapt the supply i have to power the sata drive? any info will be a great help. thanks in advance.
 

A:Solved: sata hard drive power connection

9 more replies
Answer Match 54.18%

So i found an old sata hardrive that was stored for about 2 years.
While the computer was on, i tried to plugged the Hardrive in the SATA power connector cable, as soon as i plugged it in the power connector there was smoke coming from the connection and my computer immediately shutdown.

Can someone explain what happened? I though you could connect devices while the computer was on without any issues?

More replies
Answer Match 53.76%

The situation: Dell Inspiron 600M. Laptop won't turn on, when I press the power button, no response (at all). I think it's either the power supply or the adapter. The only reason I think it is the adapter is because the green LED doesn't come on, but the user said it hadn't been coming on for some time before the laptop stopped working altogether. The user has already gotten a new computer and really only cares about the data. I'm trying to decide the best direction to go: Adapter or SATA/ATA to USB converter? I'm pretty set on the converter, but want to make sure I won't have to reformat the HD for it to work with the adapter. I think the laptop has a PATA HD connection. Will it work on most of the converters?
Another side note: I have had no success yet finding another adapter that worked. I did try an adapter for an Inspiron e1705 (90W) and when I plugged it in it reset the adapter. I thought the adapter for the 600M was also 90, but I guess not.
 

A:Solved: Laptop-Power Supply or AC Adapter

11 more replies
Answer Match 53.76%

I bought my acer aspire one back in March of 2009. A couple days ago, the adapter started to go out on me, and when i move the cord a certain way, it disconnects and goes to battery. If i move it again, it works again.

Considering that i unplug and replug in the laptop at least once every day, is this the average life of the cord or is there something wrong with the cord itself?
 

A:Solved: Acer Aspire One Power Adapter

8 more replies
Answer Match 53.76%

Hello.

I'm having difficulties finding adapters for my 2 x 5V 2A Belkin routers.
I know the Sony PSP adapters fit so I ordered 2 from ebay but they have been wrongly described and are actually 5V 500mA.
They power up the routers but are they OK to use long term?

Best regards,
SNB
 

A:Solved: Belkin Router Power Adapter

Welcome to TSG!!

I'd continue looking for the proper output power supplies. The 500mA may work for a while, but they may be being overstressed and will likely burn out prematurely.
 

2 more replies
Answer Match 53.76%

For sometime my laptop ac power adapter has been making a squealing noise and getting very hot. Now it does not work at all. The laptop will not run off it and battery will not charge. There is nothing wrong with the laptop.
I also noticed that the adapter provides 18.5V 3.5A output
The laptop requires 18.5V 4.9A input.
Is this normal?
 

A:Solved: Has my Laptop ac power adapter blown?

Yes just get another powersupply....there are some generic ones that will work ...
 

2 more replies
Answer Match 53.76%

I was given a notebook (Dell) that needs a power adapter. Two are listed. Output the same, but one is 65W the other 90W. Since I already have a 65W one from another laptop I'm using it and I haven't noticed any problems, but when I boot up there is a message that because of the 65W adapter I may not get the full potential of the sytem. Could someone explain the message?
 

A:Solved: Notebook power adapter message

8 more replies
Answer Match 53.76%

I'm looking for a Balance laptop power adapter. I don't know anything about this computer except that it needs a power cord. The battery pack is a Li-ion EM-520P4G Lithium ion battery pack. It says 14.8V. Does anyone know what I need to get? A picture of one would help also.
 

A:Solved: Balance Laptop power adapter

6 more replies
Answer Match 53.34%

I seem to have bad luck with power cords. I went through 3 on my Toshiba laptop. Now my "new" (2 year old) DELL is starting to flicker off and on between AC and battery. Is there a way to find out where the problem is...in the cord or the inner workins of the socket? This problem is getting expenive as replacements cost run between $70 to $100+...
Thanks for any advice you can offer.
 

A:Solved: Dell power cord adapter problem

9 more replies
Answer Match 53.34%

My laptop will not stay on adapter power unless the adapter plug is pressed hard against the port. I bought a new adapter but the problem still remains so I guess it's the port's problem but I have no idea how to have it fixed. The laptop is no longer under warranty. Where can I buy a new adapter port and would it be too much like brain surgery to try to do it myself?

Thanks for any help,
Tim
 

A:Solved: Power adapter port on laptop - how to replace?

These ports are soldered to the motherboard. Replacing/repairing them consists of removing the motheboard from the laptop and soldering a new powerconnector on.

Definately not a do it yourself type thing. I would suggest a competent local computer shop. This service usually runs around $100 in my area. The challenge will be finding someone willing to work on laptops anymore.
 

1 more replies
Answer Match 52.5%

Hello again,

I have seen these adapters that you can plug into a cigarette lighter outlet in a car, and use as the power source for a laptop. I tried before with one, but am not sure if it was the right wattage or what not.

My question is, where will I find on my laptop to see what type I will need? What number am I looking for to match up with the adapter? Also, are these adapters good?

Thanks.
 

A:Solved: Cigarette Lighter Adapter power source for laptop

7 more replies
Answer Match 52.5%

Hi. My power adapter cable recently broke, so i replaced it. But I accidentally got the 90 W one when I was meant to get the 130 W. When I plugged it in, for some reason, i couldn't access the internet or my home network anymore.

A lot of the network adapters in device manager have exclamation marks next to them:
I tried updating the wireless device driver, but it didnt change anything.

Any ideas what I might be able to do to get it working?
 

A:Solved: Cant access internet or network after plugging in different power adapter

16 more replies
Answer Match 50.4%

My laptop will no longer turn on.  When the AC adapter is plugged in, the LED light is white indicating power is arriving at the laptop. However, nothing happens when I push the power button. Troubleshooting steps I have completed already include: Hard reset (several times including after each step below)Tried starting without the batteryRemoved all removable components and reseated themRemoved all removable components as well as bottom cover. Cleaned with compressed air. Put everything back.Nothing appears wrong and nothing happened between the last time it turned on and this time that I am aware of. The laptop is out of warranty, and I am pretty handy with computers. Is there anything that can be suggested short of a hardware replacement that would help get this resolved? TIA

More replies
Answer Match 50.4%

The tips I got with this Kensington 33197 power adapter have numbers stenciled on them like N3, N5, N19, etc. The tips sold on their web site make no mention of the "N" numbers and have numbers like K20059, K20050, etc. and there is no cross reference.

You can also see a complete reference for "N" numbers to all the laptops they support at the above link. Again, no mention of the numbers Kensington uses on their site.

I need a cross reference for these kinds of numbers.

Kensington referred me to their telephone tech support; but, there is a language or cultural barrier that prevents their understanding what I need.

Does anyone know of such a reference?
 

A:Need power tips reference for Kensington laptop power adapter

6 more replies
Answer Match 49.56%

I just picked up the above adapter. I comes with its own power source. I picked this up to get the info off of a hard drive from my old computer that is dust. The mb is shot but the hd is fine. Now when I hook up a cd/dvd rom drive to this adapter and plug the usb into my new machine with Vista, it detects it and shows the drive and it works, no problem. But when I try the hd it detects it, installs the drivers and then says it is ready to use but the drive or a new mass storage drive letter does not show up. Under device mgr it just shows the title of usb device not mass storage. Again, the attached hd does not show up under my computer so I have nothing to double click on or open to get to my files. Any ideas? My new computer all updated bios and chipset drivers so I'm pretty much set there.
Thanks for any help.
 

A:IDE/Sata to USB 2.0 adapter

go to control panel, admin tools, computer management, disc management

after plugging in the drive, select assign letter or add drive letter.
 

1 more replies
Answer Match 49.56%

I am trying to use a usb adapter to move files off my old hard drive (ide) onto my new system (sata). It does not show up in windows explorer but does in disk management. It wants to initialize the drive which brings me to the question of whether or not that will erase my files on old drive which I am trying to access. I have read thru several forums and have seen some yes some no answers, at this point I am totally confused, I can not afford to lose the files on the old drive. Any help will be greatly appreciated. Thank you in advance.

A:Ide/Sata usb adapter

  
Quote: Originally Posted by alibren


I am trying to use a usb adapter to move files off my old hard drive (ide) onto my new system (sata). It does not show up in windows explorer but does in disk management. It wants to initialize the drive which brings me to the question of whether or not that will erase my files on old drive which I am trying to access. I have read thru several forums and have seen some yes some no answers, at this point I am totally confused, I can not afford to lose the files on the old drive. Any help will be greatly appreciated. Thank you in advance.


Old drive (with data) is initialized (what OS?) and so should not be or you will lose the data. New drive (empty) may need to be initialized before use.
Ken

6 more replies
Answer Match 49.56%

I have a good connection from HD thru the adapter to this computer, both Vista home premium. What I want is the Photos that were on my desktop. What should I be looking for in the hard drive to get these. I back up every couple weeks but went to an air show and didn't back these up and would like to get them.Where would they be
 

A:SATA Adapter to HD

10 more replies
Answer Match 49.56%

ok here's the deal. I have built my own computer. It's not great, but it does everything I need it to. The only problem I have with it is it only has one ide slot. It has four sata slots open, but none of my stuff has sata plugins. They all have ide. Is there an adapter out there that will convert the sata slots on my motherboard into ide slots? If so what is a good one to use.
 

A:sata to ide adapter?

I think a good solution would be to get a PCI card with IDE controllers. Of course, you need a free PCI slot but the card should have two controllers (connectors) that will handle two IDE devices each.

Click here to see an example of such a card. Mind you, I'm not endorsing this exact card since I don't have one. However, it's to show what I'm talking about.
 

10 more replies
Answer Match 49.56%

Hello,

I recently bought a USB to SATA/IDE adapter so I could backup data from several old laptop IDE HD's. Worked great! Now I am trying to use on standard IDE hard drives and I can't veiw the data. The system i'm using is running XP. Would anyone now why these hard drives show up in Device Manager as being seen as hardware but no data can be viewed?

Thanks in advance for any support on this matter!

Jack
 

A:USB to SATA/IDE adapter

9 more replies
Answer Match 49.56%

Im lost. I have an external hard drive that I use for school. I need to connect it to my computer at home. It has IDE cables. Im not sure which to get for it. Help?
 

A:SATA Adapter

Cheaper than an actual adapter (and faster)would be a PCI SATA controller card. This one has IDE connections as well. http://www.newegg.com/Product/Product.aspx?Item=N82E16816124009
Note that versions costing less than 35$ only come with SATA1 speed.
 

1 more replies
Answer Match 49.56%

I just purchased an adapter to convert a sata hard drive to be used with an ide controler. When i go to install windows XP it recognizes a hard drive but can only see an unknown disk of unknown size. The adapter is an RXD 629A, the hard drive is a seagate baracuda 250GB
 

A:ide to sata adapter

Most of those adapters don't work right, sorry to say.
 

3 more replies
Answer Match 49.56%

He guys today i buy new optical bluray drive.but its interf with sata and i have ide port..

And i only want to know that the sata to ide adapter will it slow the transfer speed or burning speed..
Pls reply fast

A:sata to ide adapter

if their is only ide then then you will need an adapter so if it slows transfer speed not much you can do about it but get new motherboard. burn speed you will want to burn at the lowest speed anyways to get the best quality burn.

4 more replies
Answer Match 48.72%

Hi,
I have a brand new core 2 duo system i'm building with an Intel DG965WH board. The only HDD I have and would like to use is IDE/ATA. This is a problem on my board because it is an SATA board. I'm using the only PATA/IDE channel for my optical drive and tried putting the harddrive on that channel as a secondary drive but that gave me alot of problems. A friend recently gave me an adapter that connects to my IDE harddrive and allows me to connect the drive using a SATA connnector. I powered the drive and the device using a floppy power connector in the adapter. When I boot the machine, before I even get a chance to go into BIOS, the system freezes with a black screen and gray solid cursor that doesnt blink. If I disconnect the device, the system boots fine without the harddrive. Any ideas or suggestions? Any help would be greatly appreciated.
 

A:IDE to SATA adapter problems

11 more replies
Answer Match 48.72%

I had troubles connecting my 3rd IDE hard drive (Seagate 80GB) to my new motherboard (Asus P5K). I bought a SATA->IDE adapter since the motherboard has only two IDE slots. That adapter was a cheap one. It didn't work. Strangely, once out of dozens of tries it did work, but only for one bootup (no idea why, tried everything).

Then I bought a new adapter, similar, but a bit more expensive and with some more leds on it for status reporting. It is also a basic attach-to-the-IDE-drive-model. The new adapter does actually work. This time, it fails to be recognized at every 10th boot or so though. The BIOS SATA recognition times out and the drive is not recognized. It will be recognized if I just reboot again (soft reset is ok).

What could cause this strange "random" behaviour? I have two main suspicions myself: the motherboard is faulty or the power supply is just at the limit. The latter is kind of not valid though in the sense that I think it doesn't matter if I add or remove peripherals, the behaviour will stay the same.

I don't think the drive is faulty since it worked fine with the previous system (different motherboard and power supply, no SATA to IDE adapter).

Now I also encountered a new problem: I get "Delayed Write Failed" in WinXP when installing a game. The drive will vanish from My Computer after that failure. I found many solutions to that and I have to try them one by one. But I was wondering if someone could connect the dots... Read more

A:SATA to IDE adapter not always recognized

I'd go with your assessment of an underpowered power supply. Do try disconnecting extra drives for a test.
 

1 more replies
Answer Match 48.72%

Howdy gents,
I've been browsing everywhere on the internet, but I just cannot, for the life of me, find a SATA power supply header to molex adapter. (As in, SATA female to molex male.) Do they even exist, or is there some voltage issue that renders such an adapter not possible?
Backstory, if you're interested:
I bought a new power supply while trying to address my Machine_Check_Exception issue I was having a while back. (FTR, it did turn out that that's what was causing the problem after all.)

Now, it's a nice Antec 400w that had a super-fat rebate, but I swear, nowhere on the box did it say it had four SATA headers. I expected one or two, maybe three at most... but this thing has four. I don't have any SATA devices, and I'm going to order some new case lighting and I really don't want to start using splitters or go ballistic with pass-through connectors. I should have done my homework before buying this PSU, but the rebate deal on this thing ended the next day.
 

A:SATA/Molex Adapter

9 more replies
Answer Match 48.72%

I just got my new Vantec IDE/SATA to 2.0 USB Adapter installed. I use it on my laptop to give me extra storage space.. or plan to.. this drive already has a good copy of Win 7 installed and i'd like to boot into it from the USB adapter so it will be easier for me to find out what i need to back up.

I did try to boot from USB and windows does start to load then crashes.. I don't know if it's due to the Vantec unit or if I just need to repair the MBR on the drive. The drive has been sitting in a safe place for about 8 months not being used.

A:Can you boot Win 7 from a Ide/Sata to UBS adapter?

There is a way but its not worth it if you ask me, Use the Drive as storage or send it to me, Ill use it.

7 more replies
Answer Match 48.72%

I have a Samsung SATA 250 gb HDD. I used a IDE to SATA adapter to attach the HDD to my Main boards IDE port. When I start the PC everything is fine, Windows loads normally and so on. But after 2-3 minutes the system totally hangs and then screen goes black. I had to unplug to restart the pc. Can anyone help me with this.
 

More replies
Answer Match 48.72%

I have just recieved the dvd rewriter drive I purchased on ebay I dont know if I was careless reading the write up, but the back socket looks like a sata socket is there such a thing as an adapter to change sata to ide. Thanks.

A:dvd drive adapter sata to ide

Heres one; http://www.newegg.com/Product/Product.aspx?Item=N82E16812186007

Or shop around with keywords "SATA to IDE adapter" at pricewatch.com and tigerdirect.com.

4 more replies
Answer Match 48.72%

First of all, I know this is a really long post, but I tried to include all the information I've acquired so far. Thank you in advance for reading through this whole thing to help me

In anticipation of a new HD I'm going to be getting soon for my laptop (I hope) I've been trying to decide what to do with my current laptop HD. I want to use it as an external HD for storage (or maybe to boot other OS's off of, I haven't decided yet). So I searched through eBay and basically found two solutions to use it as an external HD: A SATA/IDE to USB adapter, or a HD enclosure, with different pros and cons for each. I also have several older internal desktop HDs around my house that I'd like to use as external storage devices as well, so that plays a part into what I want to get. I'm going to list the pros and cons of each possible solution that I can think of, and then if anyone has anymore that I didn't think of or more information about which setup is best or the questions I have, I'd appreciate it. I'm trying to decide which one is going to be best solution.

What I want: A way to interchange and connect internal laptop and desktop HDs with sizes up to 1TB to my computer through the USB ports. If the 1TB support isn't possible for my price range (Trying to keep it to $5 on eBay; no more than $10) then at a minimum it should support a laptop HD up to 500 GB. Preferably something hot-swappable, with as few cables as possible.Also, the more support for different types, connection type... Read more

A:IDE/SATA Adapter vs. HD Enclosure?

Sorry Adam, but I'm not very good on hardware so I wont be much help here. I've posted this exact thread over at TSF so you can benefit from the combined knowledge of the two forums:

IDE/SATA Adapter vs. HD Enclosure? - Tech Support Forum

Tom

16 more replies
Answer Match 48.72%

Hi all,

I just finished building my new PC, And a stupid error on my part, I just noticed I only have 1 IDE slot, the rest are SATA. Now i'm looking for an adapter or two to hook up my DVd drives...I tried a PCI Card with the option for IDE..but the dirvers would not install, plus i'm running Vista.

So bottom line can anyone suggest a good Adapter to plug in my IDE drives to my SATA ports

THANKS!
 

A:Recomindations for a IDE to SATA ADAPTER

6 more replies
Answer Match 48.72%

okay.. some partitioning with PartitionMagic went wrong a few days ago on one of my computers, and it won't boot anymore. In Winternals Disk Commander off of a bootable CD, I can see all of the files that I would like to recover off of my hard drive.. but it won't let me back the data up to anything but a floppy, which obviously isn't an option.

Anyhow.. what I want to do, is to use another hard drive I have, which has XP installed on it, to boot off of, and then rescue the files from the failing hard drive. My motherboard only has SATA connectors though.. and the spare hard drive is IDE. I got an IDE to SATA converter (Syba).. but it's not working.

When I connect the IDE with the adapter, the hard drive is set to master.. all cables are connected.. all power plugged in, but I get an error message.. something like, "Media Check failed. Please check cables."

Anybody know what's going on? I know the hard drive is fine.. I can boot off of it fine on another computer, where the mobo supports IDE drives... Could the converter be the problem?

I can't see the drive in the bios either... I've tried changing a few settings, but nothing seems to remedy my little problem.

Any ideas? I'd be thankful
 

A:IDE to SATA Adapter Problems..

You're saying you don't have any cdrom drives in your computer? That's strange. If you do, remove the cable from one of those and attach the IDE as a slave or if only one cd drive, attach the IDE to that cable as Master.
 

3 more replies
Answer Match 48.72%

Can't get new drive on External USB to Sata adapter to boot

I just did a clone of my hard drive (250GB) to a new hard drive (500GB) using Clonezilla.

The dirve appears to have copied correctly except for signature conflict since I now have
two HDs with the same signature.

I took the 250 drive offline (physically) and attempted to boot the 500GB drive using the
external USB to SATA connector.

Window 7 logo came up, then gave me choice to "Start Normally" or "Repair"
Start Normally showed Windows Icon and then threw me back to BIOS.
"Repair" locks up (freezes) as doesn't recognize my keyboard.

Putting the 250 drive back, system boots as before.

QUESTIONS:
1) With all this new "Secure Boot" and UEFI is their anything I need to do differently -- BIOS setting since drives are Not the same size?
2) Any idea what's up?

THanks
David

A:Booting HD through USB to SATA Adapter

If that is a W7 system, it should boot. I cloned my system the other day (with Macrium) and that booted immediately from my external drive.

A UEFI system is another matter though. With UEFI and on the high seas you never know what is going to happen, LOL.

7 more replies
Answer Match 48.72%

Hi,
I have an old 80GB WD hard drive (IDE) and I want to use it on my newer PC, which uses SATA. I got a IDE to SATA adapter on eBay, and before I try to hook it up, I wanted to know if there's a high probability of some sort of short circuit or something that may fry my power supply.
I'm not at all concerned about what may happen to the old hard drive, but I am concerned about the rest of my PC.

Thanks for any info on this.
 

A:IDE to SATA adapter - can cause malfunction?

16 more replies
Answer Match 48.72%

Hello, I am trying to connect my SATA DVD drive to my Dell PC Via "3 PORT SATA SERIAL ATA + 1 IDE VIA 6421A PCI CARD". My Dell Is an XP Home edition 2004 and when i Connect everything together the PC will not fully boot. I have tried connecting it through all three IDE plugs, i have tried unplugging all other IDE plugs and only using the SATA Adapter's and the Mother boards and i have tried using the USB's IDE plug but when i Boot the System it says that the primary drive 0 seconadry drive are not found. I have a way of powering the DVD drive Via Molex CK3 mini and have tried booting both with the drive on and the drive off. Once before, I had gotten the PC to boot by using the secondary drive's IDE and leaving all other IDE ports in tact and the PC booted but now i have tried everything and i can't get it to Boot again.

How do i get the PC to boot and detect my SATA DVD drive through my SATA IDE Adapter?
 

A:IDE to SATA adapter not working

SATA to IDE adapters typically do not work (or work properly) for CD/DVD drives.
 

1 more replies
Answer Match 48.72%

This is a common problem (I see lots of posts)
The problem source is the [Dell] AC adapter.  PA-21 Family, 65W, P/N: NX061.  It is made in China.
I have an XPS M1330.  Using Dell after warranty service, replaced the Mother Board twice, replaced the battery twice, replaced the AC adapter twice - not fixing it.
Turns out the power warning message is very informative.  It states "Please connect a Dell 65W AC adapter or greater for best system performance".  So, I plugged in my Dell 95W adapter - WOW Problem Solved.
A lab test of my new Dell 65W AC adapter shows it to be 64.6 watts.  If this unit gets hot (like after several hours of use), it may not put out the full 65 watts - the system may not recognize the adapter, it may power the system ok, but won't charge the battery.
These units burn out after only a few months of use. Their cables are too fragile. If Dell's or their supplier's Quality Control can't produce a reliable 65W product - I found seveal "Made In USA" universal adapters.
 

A:AC Adapter - Alert - "AC power adapter wattage and type cannot be determined"

Well my solution was simple.
I just removed the battery pack and powered up my notebook. Then I turned off the notebook replaced the battery pack and VOILA. The error message was gone.

10 more replies
Answer Match 48.3%

I have one Hiitachi Hard drive with data on it from my old computer.
I would like to transfer the data from this hard drive to my new computer.
For that I bought a USB IDE/SATA adapter from VZTEC, VZ-UA2259.

The old hard drive has two partitions. On the first Partition is Windows 7 Home Premium 64 bit. The second partition contains no system, just data.

Problem: I connected the Adapter with the old hard drive, plugged it in and I saw the two partitions. I was able to download some data. Automatically a driver was installed for the new hardware.
I disconnected the old hard drive to continue the next day.
Next day, I connected the old hard drive to my new computer and the partitions were not shown. Instead I got a message asking me to format the two partitions.
I disconnected the drive and re-connected it...Same problem.

I went to my second computer, also W7 HP64bit, Connected the hard drive.
First time worked, I saw the two partitions of my old hard drive. All following attempts failed to connect the disk.

What am I doing wrong?

A:USB IDE/SATA adapter, Connection problem.

If you can locate the HDD in "MyComputer" (WinKey + E) , then "Right-click" - "Properties" - "Tools" and schedule a CHKDSK for the faulty HDD after repairs has been made remove & reinsert.Post back!!

9 more replies
Answer Match 48.3%

My old laptop died of a bad hard drive controller but I managed to rescue the hard drive, so I thought I'd save money and scrounge up a laptop that didn't have a hard drive and stick the old one in. And without thinking about it any further, I bought one that required a SATA hard drive and mine was IDE. So far I've been unable to find anything so I have to ask: does an adapter to use a 44-pin IDE hard drive in a SATA notebook exist? I'd really appreciate any help anyone can give me.
Thanks,
Chris
 

A:Does it exist: Notebook IDE to SATA adapter

6 more replies
Answer Match 48.3%

All the other problems seem to be the other way around.

My 2 DVD writers are on the primary IDE port. Had 2 x 80GB HDD's on the 2 SATA ports. Upgraded 2nd HDD to 320GB. No problems. Decided to use left-over 80GB HDD as backup disk. Installed an adapter. Plugged into secondary IDE port on motherboard. Did CMOS changes.

Booting up has three (seemingly random) results:
1. Boots up normally
2. Boots, but takes 6 minutes from "Starting Windows" to password screen
3. Never gets past "Starting Windows". This is the most common.

When it boots up normally I can use the drive. Formatted it. Changed label. Did system image.

Anybody had any success doing this?

Later edit: Tried with PCI SATA adapter and that works 100%.

A:SATA drive on IDE port with adapter

is Sata <-> IDE adapter set to master/slave or cable select? may help

3 more replies
Answer Match 48.3%

Hi all

I've searched for the answer to this query, but haven't found exactly what I'm looking for. Apologies if this is a duplication and I've missed it.

The HDD died in a spare PC a while ago and when I finally got round to buying a replacement I unfortunately bought a SATA one instead of an IDE. In an attempt to prevent more money wastage, I decided to try an adapter to try and get the new HDD working.

I've connected it all up, but when I try and install an OS the HDD is not recognised. Can some kind soul please talk me through any possible solutions or have I just cocked up (again ) and wasted my money.

Thanks in advance
Sue
 

A:SATA drive to IDE via adapter - HDD not recognised

XP does not natively support much new hardware, including SATA drives.

If you have an adapter, then none of the BIOS tips in what follows apply to you. You need the driver.

Installing XP on a SATA drive
Install Windows XP on SATA without a Floppy
Resolving "Setup did not find any hard disk drives" during Windows XP Installation
"Many newer BIOS allow an Alternate method for SATA . . Go into the BIOS and check the 'Sata Operation' setting, change it to 'Raid Autodetect/ATA' if it is not already. Now try to install XP (Verbiage will vary by manufacturer)" - Courtesy of simpswr.

BIOS settings to try:
Claymore said:


you can change the controller settings in the BIOS.

Restart the computer and enter the BIOS.
The location and type of setting will vary with the make and model of the motherboard.
Here are some:

MAIN menu
SATA Mode
Select IDE Mode instead of AHCI Mode

====================

ADAVANCED or ADVANCED (BIOS) SETTINGS menu
SATA Drive Configuration
Select Compatibility (Mode) instead of AHCI (Mode)

====================

(BIOS) ADVANCED menu
SATA
Disable Auto
Enable Combination

====================

Set to PATA mode

====================
INTEGRATED PERIPHERALS menu
IDE Function Setup
OnChip IDE => Disabled
SATA DMA transfer => Enabled

INTEGRATED PERIPHERALS menu
Onboard Device
SATA => Disabled

===================Click to expand...
 

1 more replies
Answer Match 48.3%

I was looking at this and a question came up about which I know nothing. What is the difference between these:
SATA to PCMCIA adapter
Expresscard eSATA
eSATA
The intended use is to connect an SATA hard disk or SATA burner temporarily to a PCMCIA card for data recovery or burning an image of a laptop hard disk when the laptop doesn't have a DVD burner of its own.
 

A:PCMCIA to SATA adapter question

6 more replies
Answer Match 48.3%

Hey everyone. I have a notebook that recently died on me, and I'm trying to back up the data from this drive. The drive is a: "40.0GB SATA II hard disk drive - 5400 RPM, 2.5-inch form factor, 9.5MM thick - with bracket". I purchased a SATA to USB adapter kit, which claimed to support all sizes of SATA and IDE drives. Unfortunately, the provided adapter does not fit the drive. I tried to take a picture of the problem, but it's a bit blurry, so this may or may not help.

Point is, the connector on the hard drive does not appear to be a typical SATA connection. Nor is it an IDE of some sort. The only difference I can think of is that the HDD is a SATA II drive. . .are the connections for SATA II a different size/shape than standard SATA?

Anyway. I'm not sure what the issue is, so if you can point me in the right direction, I'd be much obliged. Thanks!
 

A:Problems with notebook SATA to USB adapter

9 more replies
Answer Match 48.3%

Hi,
I am not sure if this is in the correct section. I apologize if it is not.

I am trying to install windows xp on a brand new hard drive for my desktop (the old harddrive fried). The thing is the desktop is an older model and only has the cables for ide hard drives, not sata. So I am trying to install xp on the sata harddrive via the usb adapter.

i tried installing it using the desktop and i got an error message saying your computers start up program cannot gain acess containing the space you choose...etc

So i tried installing it using my laptop and everything went fine until at the end i got an error message. i plugged it into the desktop and booted from the install cd again and it did recognize the drive and the newly partitioned space. So how do i get the desktop to boot from the usb harddrive. Or can it simply not even use the sata drive?

thank you
 

A:installing os on sata harddrive via usb adapter

i'm confused. how can you plug it in your desktop when it has no cables for it (or even supports it in general) are you using an hard drive enclosure on the sata drive and connecting it via usb and then trying to boot from it?
 

3 more replies
Answer Match 48.3%

I purchased a used Latitude E6230 laptop from my employer. They took out the HDD and I have a new one to install. Apparently an adapter is needed to convert the HDD SATA (horizontal) to the motherboard SATA (vertical).
Unfortunately I can't find it on DELL's site. Any idea how I can solve this? Thanks.

A:Latitude E6230 HDD SATA adapter

Hello.
You need a HDD SATA interposer: Y5GVV - BRIDGE, CONVERTER, SATA TO MB, E6220
I've ordered a compatible one here: www.aliexpress.com/.../32661417091.html
And it works fine.
P.S.: Or you could search "hdd interposer E6230" or "SATA interposer E6230" or even "E6230" and choose needed part from one of the stores you like.

2 more replies
Answer Match 48.3%

I am putting lights inside of my XBox 360 case but I need a molex power cable.
The DVD drive inside the XBox is SATA powered.
Can someone help me find a cable that will allow me to still power the DVD drive, but also power some Molex components?
I think what I need is a SATA pass-through cable with some Molex connections. I have no idea where to look. I've tried some google searches but they haven't helped. I will be very grateful if someone can help find me an appropriate cable.
Thanks a lot,
TRBMan
 

A:where can i find a SATA to Molex adapter?

16 more replies
Answer Match 48.3%

Hello

I recently purchased a SATA to USB adapter in order to get some files from my old hard drives to my new laptop. The adapter works fine and I can access all the files of my old HDD's.

I also want to boot to my old hard drive but there seems to be something wrong. I changed the boot order in BIOS and selected the SATA to USB device as first option but when my laptop tries to boot, I only get the Windows 7 logo and then it restarts and asks to 'Repair computer' or 'Start Windows Normally'. I selected both options but it always ends up doing the same thing over and over. What could be the issue for that since my hard drive was booting just fine on my old computer?

Thanks

More replies
Answer Match 48.3%

I have an Inland Sata Ide Cable Adapter, trying to retrieve pictures and video from harddrive when I dock it to tower it does not work. I hear humming but no pop up box to or anything.
 

A:Inland Sata Ide Cable Adapter

Are you supplying enough power to the disk?? Many hard drives need more than can be supplied though USB.
 

2 more replies
Answer Match 48.3%

Hello, hi, I hope someone can help me too.

I have an external hard drive that no longer works. I have taken out the hard drives from the enclosure (there are actually two 500gb SATA hard drives inside, but the computer reads them as one 1tb drive) and they can be read by an external dock that I already own (so I know that the hard drives still work at least).

My problem is that because of how the drives worked inside the enclosure they originally came with, the data is spread across both drives meaning I can't open or move the vast majority of it, because I can't connect both drives at once.

Does anyone here know of an adapter, or dock, or cable or converter that would allow me to connect both drives, but most importantly, have read the computer read them as one drive? I've found docks that have two slots, but I can't find any confirmation that these would read two drives as one. Is what I'm looking for even a thing?

Thanking you in advance.
 

A:Twin (2) SATA Adapter/Connector

Some pics would help..........
 

1 more replies
Answer Match 48.3%

am looking for anyone who has had the need to take a sata h.d. and connect to an ide system via usb.

i am getting sata drives with problems and i need to move the data off the drive but my problem is my systems are still ide. would be nice to find an enclosure that the sata drive can snap into and then with a usb cable i can connect it to my existing system.

anyone have any recommendations.
 

A:sata to usb adapter or converter or enclosure

To my knowledge external enclosures only fit IDE drives.
You could install a pci sata controller card in your pc to access the drive.
 

3 more replies
Answer Match 48.3%

I have a mini pcie mSATA card that I want to use for a desktop of mine. Kingston sm200s3 60GB

I believe there are only 2 options.
1. SATA > SATA adapter > mSATA card
2. PCIe slot > PCI adapter > mSATA card.

As far as 2. goes; I have found a card that fits into a PCIe slot which has an input for the mSATA card.

I know that this is not the ideal way to hook up the card but I don't see any more options.

Which is there better way to go or what am I missing?

A:Mini PCIe and adapter VS. SATA

Whatever has an mSATA interface for it will work.

From here SSD Kingston 60GB SM200S3/60G mSATA p/ Ultrabook,tablet - Atera Inform?tica

its a SATA 3 device, so for optimal performance you should use something that can guarantee enough bandwith to not bottleneck it.

PCIe bandwith depends from number of lanes used (a x1 card has one lane, a x2 card has two and so on) and the PCIe revision/version of both devices. The panel on the right here gives all speeds https://en.wikipedia.org/wiki/PCI_Express so just multiply that by the number of lanes the card has and you will find out its bandwith. SATA 3 has 6 GB/s of theoretical max bandwith, although actual transfer speed does not go above 1 GB/s afaik.

This Mini PCIe PCI E mSATA Intel Samsung SSD SATA 3 III Adapter Card with Case | eBay

this SATA III Dual Port to mSATA X 2 w/ PCI-e Bracket | MSATA-2XS3-BKT

are examples of what you listed as 1, and stuff I would orient myself towards if my mobo had SATA 3 connectors already. Because... hey, why waste PCIe slots for that?

9 more replies
Answer Match 47.88%

I'm looking for help in understanding why my external 3TB WD My Book is working just fine with Win7 Pro 64bit. My PC is a Dell Precision 690, and only supports USB 2.0.

I have a new 3TB WD Green "internal" drive. Plugging it in to the PC I hit the "only 746GB seen" issue one can Google about. I expected this. The BIOS doesn't support larger than 2TB. But when I plug the drive in via a USB-SATA adapter, I still only see 746GB. I've been using these types of USB-SATA adapters for years. Internal drives are cheaper and I never need more than one plugged in at a time. The drives are mostly for backup, and (for <= 2TB) like the flexibility of being able to plug them in for higher speeds when needed.

The USB-SATA is USB 2.0 only. I'm _guessing_ that's the issue, but rather check with others here. Before I go an get an USB 3.0-SATA, someone might be able to clue me in on other things to look out for.

Given the PC itself can only support USB 2.0, now I'm curious why the MyBook 3TB even works. There is important data backed up on it.

Any ideas?
Thanks

A:Why WD 3TB USB MyBook works, 3TB via USB-SATA adapter doesn't

Quote:
Given the PC itself can only support USB 2.0, now I'm curious why the MyBook 3TB even works.


USB 3.0 is backwards compatible. MyBook will just operate at the lower limits of USB 2.0.

Are you seeing the same size limit on your MyBook as your Green?

2 more replies
Answer Match 47.88%

When I installed a TF III GTX 570 video card I lost my PCIE-X1 slot and 1 SATA port on the Inspiron 530 Foxconn G33-M03 MOBO I am still running. Now aside from the fact that I need to upgrade the MOBO...

I added a Rosewill RC-209-EX PCI-SATA adapter (SiL3114) to gain back 4 SATA ports.

The card is working fine. It is slow compared to the MOBO SATA ports but I expected that. I have a Seagate 500GB HDD and an Optiarc DVD R/W drive attached to it.

BUT..... I can not boot from either device. They do not appear in the boot options....

Based on my reading I got the "NON-RAID" (IDE/ATA emulation) BIOS from Silicon Image and flashed the card's BIOS since I will not be using it for RAID. It is just for more SATA ports.

Should I be able to "see" the PCI-SATA card and its attached devices in the 530's BIOS Setup Screen? Is it a limitation of my Dell neutered BIOS?

The RC-209-EX documentation specifically states it "supports" CD/DVD drives.

There is plenty written about booting from a RAID array configured to the RC-209-EX but very little about booting from single device.

Any input would be appreciated. I have already tried several things but with no luck.

A:Cannot boot from devices on RC-209-EX (SiL3114) PCI-SATA Adapter

Well to answer my own question.

The RC-209-EX PCI-SATA controller requires a MOBO with a BIOS that supports booting from a SCSI Contoller. It would seem that the Dell Inspiron 530 FoxConn G33-M03 MPBO does not.

Now that that is settled I can just configure it for the additional storage which is what I really need anyway.

As a side note, Rosewill technical support said that not all OD devices will work with it even though the documenation states that the RC-209-EX "now supports DVD/CD drives". I can state that my Optiarc DVD/RW drive seems to work fine with it though I will move it back to a MOBO SATA port in case I do need to boot from it.

3 more replies
Answer Match 47.88%

I have an old machine with only 2 SATA connectors and 2 PATA connectors. I need to install 3 hard drives. I don't have any PATA hard drives so I got an SATA->PATA adapter. I installed Win 8 on the hard drive connected to the adapter and it was running fine. I decided to replace the OS hard drive with a SanDisk 64G SSD and ran into problems.

So I decided to go for a fresh installation. I booted via a USB drive and installed Win 8.1 on the SSD. After reboot, it goes directly into recovery and reports an IO error. Has anyone seen this before? Thanks.

A:Boot goes to recovery. SSD via SATA->PATA adapter

Windows 8.1 is not happy on older PC's.
New Windows 8.1 requirements strand some users on 8

1 more replies
Answer Match 47.88%

Just built a moderate spec gaming PC from scratch, and all has went according to plan except when I try to install Windows 7, my hard drive won't show up.
My new motherboard doesn't have any IDE slots, but I only have an IDE hard drive. I am using a 'Pluscom Serial ATA PCI Adapter' to connect my hard drive to the computer as it has 1 IDE slot on it. I don't have a disc for drivers and don't know where to start.
I am running Ubuntu on it at the moment so I can download any drivers I may need.
Thanks for any help in advance

A:Installation won't detect my PCI adapter for IDE & SATA drives

Does the hard drive show up in the BIOS? That card may have its own BIOS menu that you will have to access to set the correct boot order. My IDE RAID card had its own BIOS setup menu that I had to access during boot up. It had its own drive detection etc. Watch your screen during boot up and you may see a message telling you what key to press to enter its setup menu. Did it come with any documentation or a driver disk?

9 more replies
Answer Match 47.88%

I just brought this product to get access to one of my hard drives and I am simply unable to get it working on my windows 7. the directions are useless, theres nothing about windows 7, only xp and vista. I seriosly hope theres a answer to getting this functioning for me. thanks for your help

A:sabrentz usb 2.0 sata/ide hard drive adapter

Hi frusterateDUDE, welcome to the forum
Have a look here; SABRENT USA / Computer peripherals and accessories / Product support page and see if they have newer drivers

I guess it is a cable device? more details would help

1 more replies
Answer Match 47.88%

ok my friend has a device to be able to use a IDE internal drive externally
via the usb port i was wondering would something like that be able to be found for a sata drive. The case i have only has 2 slots for sata and it came with a dvd lite scribe burner and a HD both sata but I unhooked the burner for now so i can use my other sata drive that already had my apps and music,movies on it from another pc. the cd burner that is hooked up is a reg ide I dont know what the name of the device he is using or if it even has a name but its pretty neat has a power cord for it and you put the hard drive in it well slide it in and he hooks the internal drive to the usb port thru it.
 

A:SATA hard drive external adapter

This one.

http://www.usbsataadaptercable.com/

Mike
 

3 more replies
Answer Match 47.88%

...to allow me to view internal hard drives on my laptop

I bought awhile back a sata/ide to USB adapter. It seems to be a pain to get drives to show up in explorer a lot of the time, it doesn't simply show up right away, so I start replugging things trying to get the particular drive to show up. Is there some item out there (inexpensive) that will allow me to connect 3.5 and 2.5 inch internal drives via USB to my laptop that isn't as bad as the adapter I use?

A:Best inexpensive SATA/IDE internal to USB adapter device?

What adapter do you use?

7 more replies
Answer Match 47.88%

i have a Dell 280 with a IDE Hard drive. I want to change to a Sata drive using one of these adapters. Dell has one for $17.99. Do these things actual work without reducing H/D speed and has any one used/ tried one?

A:Male ide hard drive to sata adapter

Add your link to the adapter, please.

8 more replies
Answer Match 47.88%

I have been trying to recover files from a corrupted hard drive. No OS will boot on it, scandisk freezes on trying to correct index errors, HDD Regenerator shows no bad sectors.

The only option left that I can see is using an adapter and trying to pull the files off through a pc, but this hard drive, Seagate Momentus ST9160821AS, has a interface that I am not farmiliar with.

I do have an IDE converter for laptops but it interfaces with pins, and I cant find a converter that fits with this one, probably because its SATA NCQ. Is there another name for this kind of adapter that i can't find?

Here are some pictures of the interface, hope somone can give me some info on it.



 

A:SATA/NCQ Laptop Hard drive adapter

You could buy an external USB Sata enclosure for the notebook drive, and access it that way. This Seagate drive should be replaced under warranty (5 year)
 

4 more replies
Answer Match 47.46%

Hello all,
I am trying to access my wife's macbook hard drive via my Windows computer using the Vantec SATA/IDE to USB 2.0 Adapter. The Apple techs said they could not get the drive to register when they hooked it up. However, we gave it a good drying with blow dryer.

The adapter works fine and all the correct drivers installed.

I am in disk management and the 250GB drive seems to be showing up. However, it is not showing up in My Computer and right click shows "assign a letter" is grayed out.

Please check out the photo:

http://s1150.photobucket.com/albums/o620/hawkpacific/?action=view&amp;current=Capture.jpg" target="_blank"><img src="http://i1150.photobucket.com/albums/o620/hawkpacific/Capture.jpg" border="0" alt="Photobucket

A:SATA USB Adapter With Macbook Formatted Hard Drive

You are going to need a utility like MacDrive
to read the files. About all you can do directly from the windows management in this instance is format the drive. (which would result in the complete loss of data on the drive)

Also if any of the apparent moisture involved got inside the housing it's very possible the data is damaged beyond recovery. Since hard drives save data to the disk by creating what is essentially rust (iron oxide) manipulated magnetically on the surface.

There is likely a free utility out there that does the job. I just don't deal with mac's very often personally so it's not something I would be aware of, you might try google.

2 more replies
Answer Match 47.46%

In the past I've migrated 7 from one hdd to another by doing a backup to a usb drive, then swapping the drives and restoring to the new one.

What I need to do now is a twist on that. My MB is one of the new p67s that has the faulty intel sata ports, and will eventually be recalled. The 4 6Gps sata ports on the board are not affected by the chipset problem, so i plan on just using them instead(plus i just got a 6G seagate drive that I wanted to use anyway).

What I envision happening is restoring to the new drive on an entirely different sata adapter and port #, and the system not booting. I assume i could get around this by booting to a command prompt and using bcedit, but am not 100% on that.

Can someone recommend a good way to do this, or if my idea sounds fine, confirm it?

thanks!

A:Need advice moving a win7 install to a new HDD and sata adapter.

  
Quote: Originally Posted by dronf


In the past I've migrated 7 from one hdd to another by doing a backup to a usb drive, then swapping the drives and restoring to the new one.

What I need to do now is a twist on that. My MB is one of the new p67s that has the faulty intel sata ports, and will eventually be recalled. The 4 6Gps sata ports on the board are not affected by the chipset problem, so i plan on just using them instead(plus i just got a 6G seagate drive that I wanted to use anyway).

What I envision happening is restoring to the new drive on an entirely different sata adapter and port #, and the system not booting. I assume i could get around this by booting to a command prompt and using bcedit, but am not 100% on that.

Can someone recommend a good way to do this, or if my idea sounds fine, confirm it?

thanks!


Hello dronf, and welcome to Windows Seven Forums.

You have left out lots of info that would help answer your question. Is this a Desktop Computer? A laptop?

With my desktop, I use a second hard drive to save an image created by Windows Seven backup utility. When the OS hard drive failed, I just swapped for a new hard drive, booted to my 7 install DVD, and restored the OS to the new hard drive.

You could do something similar and just as easy. You have the choice of saving the image on either the old hard drive or the new hard drive. If you do not have an install DVD, have Windows 7 make you a repair CD for ... Read more

6 more replies
Answer Match 47.46%

Hello! I have a SATA dvd writer (Liteon iHAS524-32) that I would like to use as an external unit by connecting it to a SATA-USB adapter. Problem is that I keep reading that such adapters may give various errors when the optical drive is trying to write. Apparently, the JMicron chips inside these adapters is to blame, but it seems that in some cases it works OK and in some other it doesn't (?!) I couldn't find out more. Also, all the adaptors about whose chip I could find something use a JMicron, all of them.

The main candidates atm are (considering also the local availablilty):
1. Digitus DA 70-148-1 digitus.info/en/products/accessories/?c=1209&p=3534 . Main positive argument: I have seen one working ok with my dvd writer (wrote 2 DVDs without problems). Cons: I know it uses a JMicron chip and some users have commented it worked OK as well but others complained about optical drive problems (see user reviews on amazon.de); only HDDs are mentioned in the manual and datasheet.
2. Manhattan 179195 manhattan-products.com/en-US/products/8847-hi-speed-usb-2-0-to-sata-ide-adapter . Main positive argument: the old version that you can see in the picture on the box in the above link as well as here: conectica.ro/display/1-63-15480-Adaptoare/Adaptor_portabil_USB_2.0_-_SATA_IDE_Manhattan.html was specified to work with optical drives as well. Maybe I could still find the old version on stock, but I kind of doubt it. Also, it has lifetime warranty.The new version, h... Read more

A:Please suggest a SATA-USB adapter compatible with optical drives

Nobody knows?
 

3 more replies
Answer Match 47.46%

Hey all,

I'm upgrading my SSD from an Intel SATA II 320 120GB - which has worked very well for me - to a Samsung SATA III 840 EVO 250GB. My computer doesn't have any native SATA III hookups, but I do have several PCIe 2.0 slots that are open and ready to be used. As such, I've decided to purchase a PCIe to SATA III adapter so that I can run the drive through the adapter, and hopefully get better performance than using SATA II.

My first question is, is there a recommended controller or card that anyone here has used? I've heard that while sub $100 cards can work, most use Marvell controllers which have mixed performance. However I'm still unsure. For example, here's an affordable SATA 3 card, and the reviews are mostly positive, but it is a Marvell controller. I've read that LSI is a reliable brand that makes excellent controllers, but the cost is prohibitive for most upgraders.

I know that if I get any PCIe card, the first thing I should do is get at least a dual lane x2 or x4 card. Anything higher than that will be overkill, but x1 will probably be too little bandwidth.

To clarify, I'm not going to be running RAID with any of my drives. I have a standard 500GB HDD that I'm going to leave on the SATA II port on the mobo. I'm not sure if I should use HyperDuo mode or not if I get a card that sports such a feature. I've read that while HyperDuo is a convenient feature, SSD performance does take a dive, as opposed to a manual SSD+HDD setup.

I've also checked ot... Read more

A:Need advice on purchasing PCIe to SATA 3 adapter card

My Gigabyte motherboard has SATA III Marvell 91xx controller. Not having any problems with that.

Here is the benchmark for my OCZ Vertex 4 SSD. and my Intel 520 SSD. The OCZ is for Win 8.1 and the Intel is for Win 7 64 bit (dual boot). It shows as "SCSI" but not sure why (all the drives whether SSD or conventional are showing as SCSI).

3 more replies
Answer Match 47.46%

Hello,
I have a SATA 250Gb Seagate HDD from my desktop. Since I am away from home I brought the HDD to use with my laptop. I bought a SATA to USB adapter and was unable to use it. I don't think enough power was being provided by the power supply that came in the adapter box. The head used to spin up and then spin down over and over again. The HDD would work for no more than 3 minutes and would spin down.
Today, after about 3 months, I tried using the adapter and smoke came off the controller card as soon as I tuned on the power. I tried twice and the same repeated. Then I took the HDD to a friend's place and connected it to his pc as a SATA drive. The computer would not even power up unless I disconnected the drive.
Is there a way to get my HDD working again? Since I am a student I don't think I can afford paying a company to recover my data although I have invaluable stuff in it.
Thanks people.
 

A:SATA HDD attached to USB adapter emits smoke when tuned on

Once an electronic device smokes you are pretty much screwed.

You could buy that exact same drive and try swapping the PCB, provided you didn't blow up the motor or damage anything actually inside the drive that will work.
 

13 more replies
Answer Match 47.46%

Hey guys, I have used all my SATA ports on my motherboard (4 HDs on them), but i wanted to use my dvd burners, so I bought a IDE to SATA connector, to use on the DVD burners, the PC turns on and boots fine, but my monitor LG L192WS wont turn on, with the connector connected, what could be the problem.

A:monitor wont turn on after installing ide to sata adapter

Here is my confusion:
If the monitor will not turn on, how do you know the PC "boots fine"?
What do you see? Are there any error messages? How could you tell if there is no output on the monitor?

Do you mean that you eventually hear the Windows startup sound, but with nothing on the screen?

If so, then your new device may be conflicting with your video card. I assume if you remove it, all works normally?

If this is so, then try installing the new card in a different slot on the motherboard.

Let us know what is going on here!

6 more replies
Answer Match 47.46%

Hi there

Now these exist (SATA USB3 connectors) you've now got extremely FAST external laptop PC drives !!!!

If you've replaced a laptop drive with an SSD don't ditch the old drive unless it's REALLY old. If your machine has USB3 use a SATA==>USB3 cable to the PC laptop drive and have it as an external drive -- works SOOOOOPER FAST.

(SATA to USB2 is fine too so in any case don't "Bin" the old drive --use it for backups etc).

Cheers
jimbo

A:Sata==>USB3 adapter Now really GREAT use for old laptop drives

this adaptor is the best way to broke the connectors on the drive. If you want to use an external HD, better use an enclosure like this one, it cost only $ 19 ;

if like me you need a bench r solution to transfer info for many drive , a dock station is the best for not damage the connectors

5 more replies
Answer Match 47.46%

some people change ide to ahci in the bios then it worked.

some people put drive on master, hey then it worked
Second PATA hard drive not detected in the BIOS? - Yahoo Answers

some people put drive on cs, hey then it worked
SATA to IDE Adapter, Drive Not Detected in BIOS - Hard Drives - Storage

What do I do to make it work for me?
The yellow led lights up
the sata cable plugged into sata port and tried multiple ports.
Under sata configuration I tried AHCI which caused windows to BSOD
I switched that back to IDE

This Asus p5qc has a PATA DVD drive lugged into MB IDE port
And a sata drive plugged into sata port.
And a sata drive plugged into sata port.

A:sata to ide adapter do not see PATA hard drive in the bios?

Following this guide, i made it so windows boots ok with bios setting to AHCI
AHCI : Enable in Windows 7 / Vista

Still the bios does not show drive with adapter connected.
I have tried 4 HD and a dvd drive.

2 more replies
Answer Match 47.46%

I am using an HP Pavilion dv6 running Windows 10.

I have retrieved a 500GB Western Digital Scorpio Blue HDD from another Windows laptop. This is the main hard drive with the OS installed.

When still in that laptop, the computer won't boot up at all. It brings up the very first screen for about five seconds, and then the entire laptop powers down, then repeats infinitely.

I am using a Apricorn brand USB to SATA adapter to read the HD externally. The adapter works and is working properly, having tested with another drive.

When I plug the adapter in, the drive spins up almost immediately a "G" partition appears in "Devices and Drives" on my laptop. This partition is labeled "System Reserved" and is 100MB in size with no data on it.

A minute or so later an "H" partition appears, but that's the extent of it. A green loading bar starts at the top, fills, and just sits there loading. If I try to click on the H drive to open it, a spinning wheel appears and it seems to try but nothing happens. If I right click on the drive and click properties, nothing comes up.

If I try to open Disk Management while the disk is plugged in, the window opens but it just hangs at "Loading Virtual Disc" but won't open up.

I attempted to run ChkDsk from the dos prompt. When I type CHKDSK G: it says it finds no problems. When I type CHKDSK H: it just hangs there (surprise surprise.)

At this point I don't know what to do and I�... Read more

More replies
Answer Match 46.62%

HI,

I purchased an adapter on Ebay that was supposed to allow me to connect my ide hard drive to my sata mobo connectors. My mobo has primarily sata but it has one ide which is already connected to my ide hard drives.

I have tried everything I can think of. connecing this and that, reversing connections, nothing workd. The instructions I was given were awful and the person I purchased is not helpful in answering questions. He hasn't responded.

Once connected I can't get it to show up in the bios The hard drive is an IDE Seagate 400gb drive. I am connecting to a sata connector on my mobo. I already have two other sata devices connected, they are two dvdr's .

My computer specs are listed above in the computer icon. The converter I purchased is listed here:
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=300473666570&ssPageName=STRK:MEWNX:IT

Is there a trick to doing this?

Thanks.
 

More replies
Answer Match 46.62%

hello alll
im new here and hope you can help me fix my problem
basicly iv got a adapter for a sata hard drive to go to ide on my motherbourd in the bios it picks it up, but when i let it run i get the primary master hard drisk fail message, im not sure what to do.

im using a asus x series motherboard

cheers inn advance for the help
 

A:sata hdd to ide hdd adapter-primary master hard drisk fail

Might check the adapter for a master/slave jumper.
If it is the only drive on the cable,set it to master.
 

2 more replies
Answer Match 46.62%

Interaction (interface?) between a Sabrent USB 2.0 to SATA/IDE Hard Drive Adapter Product Code: USB-DSC5 and my Windows 7 Home Premium 64-bit

I am having an issue with the following situation:
When connected to IDE Drives Maxtor and Western Digital, and through the usage of Windows 7 it tellls me that the Hard Drive "is not ready". Is that a message originated by the Windows 7 software?
If so how do I go about "getting the disk ready" so i could change disk type or number or sizes of each partition and/or reformat?
I would appreciate your support to help me solve this unexpected report from the Windows 7 interaction with this adapter and the Hard Drives it holds, 40 GB and 80 GB IDE drives Maxtor and Western Digital. I am trying to use Windows (or some other third party software) to resize the partitions, change the disk type and eventually reformat.

Thank you kindlly

A:Clash between Sabrent 2.0 to SATA/IDE Hard Drive Adapter with Windows

Check the power & DATA cables.
When using IDE HD Drives, make there are set to master.
http://sabrent.com/product-manuals/USB-DSC5_Manual.pdf

1 more replies
Answer Match 45.78%

For the last two weeks, every time I start my Dell INSPIRON E1705 while using the power supply I am greeted with the following message. "The AC power adapter type cannot be determined. Your system will operate slower and the battery will not charge. Please connect a Dell 90W AC adapter or higher for best system operation". I press the F1 Key and everything works fine. I've read about this on other websites and most say it's a design flaw in the power supply after the cord has been properly wound around the supply as designed. Apparently a few of the cords internal wire strands become broken and cause this message. My computer is from June 2006 and shouldn't be having this issue so early...or ever. This seems like a flaw that should have created some type of manufacturers recall since so many people are having this issue. I'm of course out of warranty, will Dell replace this free of charge?
 
`

A:Power Supply - "The AC power adapter type cannot be determined....."

You are correct, the failure is due toloss of the power supply ID signal. Sometimes this happens because of strain on the plug, which breaks the signal wire. Some even are so severe that the insulation breaks away from the plug; this is due to rough handling. The other cause is one or more of the power socket solder connections to the system board become broken. This also is related to severe handling. I have seen one case where all three power connections and three of four mechanical connections were disconnected. If the power supply is bad, a replacement will cure the problem. If not, then the socket is bad, and this will require a system board replacement. If you are experienced, you can try to resolder the connections. I am experienced and was not able to get my daughter's E6000 to work by resoldered. More recent Dells are using a replacable power connection board which is a much cheaper repair.

64 more replies
Answer Match 45.78%

Here's what you X58 guys can look forward to in the near future.

[ame="http://www.youtube.com/watch?v=s8kSW5i3FS8"]YouTube - Exclusive preview of the GIGABYTE EX-58 EXTREME2 motherboard[/ame]

A:USB 3.0 - SATA 3 - and 3X USB power for X58

Its so pretty!

2 more replies
Answer Match 45.36%

Even though the following is a question, I do welcome opinions on what the right answer is to my situation: I have an IDE type motherboard. The motherboard model number is SV266M (See http://www.newegg.com/Product/Product.aspx?Item=N82E16813183009 [Date accessed: 02-28-2015 @ 7:37 PM]). I am not sure but I believe my motherboard was made in 2004. Is there a way I can connect a 1 Terabyte Sata Hard Drive to my SV266M motherboard? I have heard of a Sata Bridgeboard (SATA to IDE). I have not used one before. A matter of fact, I have only seen the Youtube Video below.
How to connect SATA devices in a PATA (IDE) only PC system
https://www.youtube.com/watch?v=BwRClahcUCI
(Date accessed: 02-28-2015 @ 7:40 PM)

They even sell this bridgeboard (SATA to IDE) online.
Kingwin SATA to IDE Bridge Board ADP-06
http://www.amazon.com/Kingwin-SATA-Bridge-Board-ADP-06/dp/B002SZDOM6
(Date accessed: 02-28-2015 @ 7:45 PM)
The bridgeboard above above has a 3.7 out of 5 stars. However, I am not sure if this bridgeboard would be compatible with my motherboard. If there is a better bridge board (SATA to IDE) that you know of, please let me know. Do you think the Bridgeboard (SATA to IDE) would work with the SV266M motherboard?
 

A:Solved: Will Sata Bridgeboard (SATA to IDE) work on IDE Motherboard

They sometimes work and sometimes they don't. To make things worse your motherboard is really old and uses a VIA chipset which had a lot of compatibility issues.

You may want to look into a PCI SATA Controller card instead if you need to use this dinosaur: http://www.newegg.ca/Product/ProductList.aspx?Submit=ENE&IsNodeId=1&N=100007863 600022728
 

1 more replies